[media] DocBook/dvb: Use generic descriptions for the frontend API
Move generic stuff into gen-errors.xml, and remove them from
DVB API. While here, removes two bogus error codes that aren't
supported or used on Linux: EINTERNAL and ENOSIGNAL.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] dvb-bt8xx: Don't return -EFAULT when a device is not found
When a device (or their PCI structs) are not found, the error should
be -ENODEV. -EFAULT is reserved for errors while copying arguments
from/to userspace.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove generic errors from ioctl() descriptions. For other ioctl's,
there's no generic section. So, just keep whatever is there.
Also remove the EINTERNAL error code, as no DVB driver returns
it, and this error code is not defined on POSIX or on Linux.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just like the V4L, MC and LIRC API's, point to the generic error
chapter for ioctl's. This will allow moving generic error codes
to just one place inside all media API's.
A latter patch will remove the generic errors from each specific
ioctl.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] DocBook: Use the generic error code page also for MC API
Instead of having their own generic error codes at the MC API, move
its section to the generic one and be sure that all media ioctl's
will point to it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] DocBook: Add a chapter to describe media errors
There are several errors reported by V4L that aren't described.
They can occur on almost all ioctl's. Instead of adding them
into each ioctl, create a new chapter.
For V4L, the new chapter will automatically be listed on all
places, as there's a macro used everywhere there.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 14 Jun 2011 13:04:06 +0000 (10:04 -0300)]
[media] v4l2-ctrls: improve discovery of controls of the same cluster
The implementation of VIDIOC_G/S/TRY_EXT_CTRLS in the control framework has
to figure out which controls in the control list belong to the same cluster.
Since controls belonging to the same cluster need to be handled as a unit,
this is important information.
It did that by going over the controls in the list and for each control that
belonged to a multi-control cluster it would walk the remainder of the list
to try and find controls that belong to that same cluster.
This approach has two disadvantages:
1) it was a potentially quadratic algorithm (although highly unlikely that
it would ever be that bad in practice).
2) it took place with the control handler's lock held.
Since we want to make it possible in the future to change control values
from interrupt context, doing a lot of work while holding a lock is not a
good idea.
In the new code the algorithm is no longer quadratic but linear in the
number of controls in the list. Also, it now can be done beforehand.
Another change that was made was to so the try and set at the same time.
Before when S_TRY_EXT_CTRLS was called it would 'try' the controls first,
and then it would 'set' them. The idea was that any 'try' errors would
prevent the 'set' from happening, thus avoiding having partially set
control lists.
However, this caused more problems than it solved because between the 'try'
and the 'set' changes might have happened, so it had to try a second time,
and since actual controls with a try_ctrl op are very rare (and those that
we have just adjust values and do not return an error), I've decided to
drop that two-stage approach and just combine try and set.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 18 Jun 2011 10:02:20 +0000 (07:02 -0300)]
[media] v4l2-event: add optional merge and replace callbacks
When the event queue for a subscribed event is full, then the oldest
event is dropped. It would be nice if the contents of that oldest
event could be merged with the next-oldest. That way no information is
lost, only intermediate steps are lost.
This patch adds optional replace() (called when only one kevent was allocated)
and merge() (called when more than one kevent was allocated) callbacks that
will be called to do this job.
These two callbacks are implemented for the V4L2_EVENT_CTRL event.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 13 Jun 2011 22:24:17 +0000 (19:24 -0300)]
[media] v4l2-event/ctrls/fh: allocate events per fh and per type instead of just per-fh
The driver had to decide how many events to allocate when the v4l2_fh struct
was created. It was possible to add more events afterwards, but there was no
way to ensure that you wouldn't miss important events if the event queue
would fill up for that filehandle.
In addition, once there were no more free events, any new events were simply
dropped on the floor.
For the control event in particular this made life very difficult since
control status/value changes could just be missed if the number of allocated
events and the speed at which the application read events was too low to keep
up with the number of generated events. The application would have no idea
what the latest state was for a control since it could have missed the latest
control change.
So this patch makes some major changes in how events are allocated. Instead
of allocating events per-filehandle they are now allocated when subscribing an
event. So for that particular event type N events (determined by the driver)
are allocated. Those events are reserved for that particular event type.
This ensures that you will not miss events for a particular type altogether.
In addition, if there are N events in use and a new event is raised, then
the oldest event is dropped and the new one is added. So the latest event
is always available.
This can be further improved by adding the ability to merge the state of
two events together, ensuring that no data is lost at all. This will be
added in the next patch.
This also makes it possible to allow the user to determine the number of
events that will be allocated. This is not implemented at the moment, but
would be trivial.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 13 Jun 2011 21:55:58 +0000 (18:55 -0300)]
[media] v4l2-ctrls/event: remove struct v4l2_ctrl_fh, instead use v4l2_subscribed_event
The v4l2_ctrl_fh struct connected v4l2_ctrl with v4l2_fh so the control
would know which filehandles subscribed to it. However, it is much easier
to use struct v4l2_subscribed_event directly for that and get rid of that
intermediate struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 13 Jun 2011 20:44:42 +0000 (17:44 -0300)]
[media] v4l2-events/fh: merge v4l2_events into v4l2_fh
Drivers that supported events used to be rare, but now that controls can also
raise events this will become much more common since almost all drivers have
controls.
This means that keeping struct v4l2_events as a separate struct make no more
sense. Merging it into struct v4l2_fh simplifies things substantially as it
is now an integral part of the filehandle struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andrew Chew [Thu, 23 Jun 2011 23:19:41 +0000 (20:19 -0300)]
[media] V4L: ov9740: Fixed some settings
Based on vendor feedback, should issue a software reset at start of day.
Also, OV9740_ANALOG_CTRL15 needs to be changed so the sensor does not begin
streaming until it is ready (otherwise, results in a nonsense frame for the
initial frame).
Added a comment on using discontinuous clock.
Finally, OV9740_ISP_CTRL19 needs to be changed to really use YUYV ordering
(the previous value was for VYUY).
[media] V4L: soc-camera: remove several now unused soc-camera client operations
This patch removes .enum_input(), .suspend() and .resume() soc-camera
client operations.
Functionality, provided by .enum_input(), if needed, can be implemented
using the v4l2-subdev API.
As for .suspend() and .resume(), the only client driver, implementing
these methods has been mt9m111, and the only host driver, using them
has been pxa-camera. Now that both those drivers have been converted
to the standard subdev .s_power() operation, .suspend() and .resume()
can be removed.
[media] V4L: mt9m111: propagate higher level abstraction down in functions
It is more convenient to propagate the higher level abstraction - the
struct mt9m111 object into functions and then retrieve a pointer to
the i2c client, if needed, than to do the reverse.
[media] V4L: pxa-camera: try to force progressive video format
The pxa-camera driver only supports progressive video so far. Passing
down to the client the same format, as what the user has requested can
result in interlaced video, even if the client supports both. This
patch avoids such cases.
Hans Verkuil [Tue, 7 Jun 2011 09:47:18 +0000 (06:47 -0300)]
[media] v4l2-ctrls: add v4l2_fh pointer to the set control functions
When an application changes a control you want to generate an event.
However, you want to avoid sending such an event back to the application
(file handle) that caused the change.
Add the filehandle to the various set control functions.
The filehandle isn't used yet, but the control event patches will need
this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 10 Jun 2011 08:44:36 +0000 (05:44 -0300)]
[media] v4l2-ctrls: add v4l2_ctrl_auto_cluster to simplify autogain/gain scenarios
It is a bit tricky to handle autogain/gain type scenerios correctly. Such
controls need to be clustered and the V4L2_CTRL_FLAG_UPDATE should be set on
the autofoo controls. In addition, the manual controls should be marked
inactive when the automatic mode is on, and active when the manual mode is on.
This also requires specialized volatile handling.
The chances of drivers doing all these things correctly are pretty remote.
So a new v4l2_ctrl_auto_cluster function was added that takes care of these
issues.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 10 Jun 2011 08:43:34 +0000 (05:43 -0300)]
[media] v4l2-ctrls: fix and improve volatile control handling
If you have a cluster of controls that is a mix of volatile and non-volatile
controls, then requesting the value of the volatile control would fail if the
master control of that cluster was non-volatile. The code assumed that the
volatile state of the master control was the same for all other controls in
the cluster.
This is now fixed.
In addition, it was clear from bugs in some drivers that it was confusing that
the ctrl->cur union had to be used in g_volatile_ctrl. Several drivers used the
'new' values instead. The framework was changed so that drivers now set the new
value instead of the current value.
This has an additional benefit as well: the volatile values are now only stored
in the 'new' value, leaving the current value alone. This is useful for
autofoo/foo control clusters where you want to have a 'foo' control act like a
volatile control if 'autofoo' is on, but as a normal control when it is off.
Since with this change the cur value is no longer overwritten when g_volatile_ctrl
is called, you can use it to remember the original 'foo' value. For example:
autofoo = 0, foo = 10 and foo is non-volatile.
Now autofoo is set to 1 and foo is marked volatile. Retrieving the foo value
will get the volatile value. Set autofoo back to 0, which marks foo as non-
volatile again, and retrieving foo will get the old current value of 10.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 7 Jun 2011 07:40:04 +0000 (04:40 -0300)]
[media] v4l2-ctrls: simplify error_idx handling
The lower-level prepare functions just set error_idx for each control that
might have an error. The high-level functions will override this with
cs->count in the get and set cases. Only try will keep the error_idx.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] Stop using linux/version.h on the remaining video drivers
Standardize the remaining video drivers to return the API version
for the VIDIOC_QUERYCAP version, instead of a per-driver version.
Those drivers had the version updated more recently or are SoC
drivers. Even so, it doesn't sound a good idea to keep a per-driver
version control, so, let's use the per-subsystem version control
instead.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] ivtv,cx18: Use default version control for VIDIOC_QUERYCAP
After discussing with Andy Walls on irc, we've agreed that this
is the best thing to do. No regressions will be introduced, as 3.x.y
is greater then the current versions for cx18 and ivtv.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changing it to 3.x.y won't conflict with the old version.
There's no namespace conflicts in any predictable future.
Even on the remote far-away case where we might have a conflict,
it will be on just one specific stable Kernel release (Kernel 10.0.12),
if we ever have such stable release.
So, it is safe and consistent on using 3.x.y numering schema for
it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] Stop using linux/version.h on most video drivers
All the modified drivers didn't have any version increment since
Jan, 1 2011. Several of them didn't have any version increment
for a long time, even having new features and important bug fixes
happening.
As we're now filling the QUERYCAP version with the current Kernel
Release, we don't need to maintain a per-driver version control
anymore. So, let's just use the default.
In order to preserve the Kernel module version history, a
KERNEL_VERSION() macro were added to all modified drivers, and
the extraver number were incremented.
I opted to preserve the per-driver version control to a few
pwc, pvrusb2, s2255, s5p-fimc and sh_vou.
A few drivers are still using the legacy way to handle ioctl's.
So, we can't do such change on them, otherwise, they'll break.
Those are: uvc, et61x251 and sn9c102.
The rationale is that the per-driver version control seems to be
actively maintained on those.
Yet, I think that the better for them would be to just use the
default version numbering, instead of doing that by themselves.
While here, removed a few uneeded include linux/version.h
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] drxd, siano: Remove unused include linux/version.h
Both drxd and siano drivers were including linux/version.h without
any reason. Probably, this is due to some compatibility code that
used to exist before having their support added into the Linux
Kernel.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] v4l2-ioctl: Add a default value for kernel version
Most drivers don't increase kernel versions as newer features are added or
bug fixes are solved. So, vidioc_querycap returned value for cap->version is
meaningless. Instead of keeping this situation forever, let's add a default
value matching the current Linux version.
Drivers that want to keep their own version control can still do it, as they
can override the default value for cap->version.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core driver can now operate in either vmalloc or dma-contig modes;
obviously the latter is preferable when it is supported. Default is
currently vmalloc on all platforms; load the module with buffer_mode=1 for
contiguous DMA mode.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Mon, 20 Jun 2011 19:14:36 +0000 (16:14 -0300)]
[media] marvell-cam: convert to videobuf2
This is a basic, naive conversion to the videobuf2 infrastructure, removing
a lot of code in the process. For now, we're using vmalloc, which is
suboptimal, but it does match what the cafe driver did before. In the cafe
case, it may have to stay that way just because memory is too tight to do
direct streaming; mmp-camera will be able to do better.
Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manjunath Hadli [Fri, 17 Jun 2011 07:01:34 +0000 (04:01 -0300)]
[media] davinci vpbe: VENC( Video Encoder) implementation
This patch adds the VENC or the Video encoder, which is responsible
for the blending of all source planes and timing generation for Video
modes like NTSC, PAL and other digital outputs. the VENC implementation
currently supports COMPOSITE and COMPONENT outputs and NTSC and PAL
resolutions through the analog DACs. The venc block is implemented
as a subdevice, allowing for additional external and internal encoders
of other kind to plug-in.
This patch implements the functionality of the OSD block
of the VPBE. The OSD in total supports 4 planes or Video
sources - 2 mainly RGB and 2 Video. The patch implements general
handling of all the planes, with specific emphasis on the Video
plane capabilities as the Video planes are supported through the
V4L2 driver.
Manjunath Hadli [Fri, 17 Jun 2011 07:01:32 +0000 (04:01 -0300)]
[media] davinci vpbe: VPBE display driver
This patch implements the core functionality of the display driver,
mainly controlling the VENC and other encoders, and acting as
the one point interface for the main V4L2 driver. This implements
the core of each of the V4L2 IOCTLs.
Manjunath Hadli [Fri, 17 Jun 2011 07:01:31 +0000 (04:01 -0300)]
[media] davinci vpbe: V4L2 display driver for DM644X SoC
This is the display driver for Texas Instruments's DM644X family
SoC. This patch contains the main implementation of the driver with the
V4L2 interface. The driver implements the streaming model with
support for both kernel allocated buffers and user pointers. It also
implements all of the necessary IOCTLs necessary and supported by the
video display device.
Tejun Heo [Wed, 15 Jun 2011 13:32:06 +0000 (10:32 -0300)]
[media] dvb-usb/technisat-usb2: don't use flush_scheduled_work()
flush_scheduled_work() is deprecated and scheduled to be removed.
technisat-usb2 already sync-cancels the only work item it uses and
there's no reason for it to call flush_scheduled_work(). Don't use
it.
projects / linux-beck.git / log