Theodore Ts'o [Sun, 14 Aug 2011 23:01:05 +0000 (19:01 -0400)]
ext4: fake direct I/O mode for data=journal
Currently attempts to open a file with O_DIRECT in data=journal mode
causes the open to fail with -EINVAL. This makes it very hard to test
data=journal mode. So we will let the open succeed, but then always
fall back to O_DSYNC buffered writes.
Clemens Ladisch [Tue, 21 Jun 2011 20:09:50 +0000 (22:09 +0200)]
mm: fix wrong vmap address calculations with odd NR_CPUS values
Commit db64fe02258f ("mm: rewrite vmap layer") introduced code that does
address calculations under the assumption that VMAP_BLOCK_SIZE is a
power of two. However, this might not be true if CONFIG_NR_CPUS is not
set to a power of two.
Wrong vmap_block index/offset values could lead to memory corruption.
However, this has never been observed in practice (or never been
diagnosed correctly); what caught this was the BUG_ON in vb_alloc() that
checks for inconsistent vmap_block indices.
To fix this, ensure that VMAP_BLOCK_SIZE always is a power of two.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=31572 Reported-by: Pavel Kysilka <goldenfish@linuxsoft.cz> Reported-by: Matias A. Fonzo <selk@dragora.org> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: 2.6.28+ <stable@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Mack [Sun, 14 Aug 2011 09:31:16 +0000 (11:31 +0200)]
ALSA: snd_usb_caiaq: track submitted output urbs
The snd_usb_caiaq driver currently assumes that output urbs are serviced
in time and doesn't track when and whether they are given back by the
USB core. That usually works fine, but due to temporary limitations of
the XHCI stack, we faced that urbs were submitted more than once with
this approach.
As it's no good practice to fire and forget urbs anyway, this patch
introduces a proper bit mask to track which requests have been submitted
and given back.
That alone however doesn't make the driver work in case the host
controller is broken and doesn't give back urbs at all, and the output
stream will stop once all pre-allocated output urbs are consumed. But
it does prevent crashes of the controller stack in such cases.
See http://bugzilla.kernel.org/show_bug.cgi?id=40702 for more details.
Signed-off-by: Daniel Mack <zonque@gmail.com> Reported-and-tested-by: Matej Laitl <matej@laitl.cz> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Takashi Iwai <tiwai@suse.de>
Theodore Ts'o [Sun, 14 Aug 2011 02:43:25 +0000 (22:43 -0400)]
ext4: don't give the "disabling delalloc" if not explicitly specified
If both delalloc and data=journalled are enabled, then a warning
message that delalloc will be disabled is displayed at mount time.
Since delalloc is the default, this means this warning is always
printed which really isn't necessary. So disable the warning message
unless the user explicitly asked for delalloc.
Theodore Ts'o [Sun, 14 Aug 2011 02:16:38 +0000 (22:16 -0400)]
ext2,ext3,ext4: don't inherit APPEND_FL or IMMUTABLE_FL for new inodes
This doesn't make much sense, and it exposes a bug in the kernel where
attempts to create a new file in an append-only directory using
O_CREAT will fail (but still leave a zero-length file). This was
discovered when xfstests #79 was generalized so it could run on all
file systems.
Randy Dunlap [Sat, 13 Aug 2011 19:34:52 +0000 (12:34 -0700)]
Documentation: kernel-parameters.txt cleanups
General cleanups to kernel-parameters.txt:
- add missing $ARCH that are being used/referenced
- alphabetize the parameter restrictions list
- spell "IA-64" as listed in arch/ia64/Kconfig instead of "IA64"
- remove trailing whitespace
- use hyphen in 32-bit etc.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Boyd [Sat, 13 Aug 2011 19:34:50 +0000 (12:34 -0700)]
Documentation: add ARM user_debug to kernel-parameters.txt
Usually kernel parameters are documented in kernel-parameters.txt
but user_debug is only documented in the Kconfig. Document the
option and point to the Kconfig help text for more info.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation: drop Linux Source Driver from kernel-docs references
Dropping LSD (Linux Source Driver) since it hasn't been available
for a long time.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wang Shaoyan [Thu, 11 Aug 2011 17:07:25 +0000 (17:07 +0000)]
gianfar: reduce stack usage in gianfar_ethtool.c
drivers/net/gianfar_ethtool.c:765: warning: the frame size of 2048 bytes is larger than 1024 bytes
Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com> Reviewed-and-tested-by: Sebastian Pöhn <sebastian.poehn@belden.com> Signed-off-by: David S. Miller <davem@davemloft.net>
error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_eth_interrupt'
error: implicit declaration of function 'request_irq'
error: 'sh_eth_interrupt' undeclared (first use in this function)
error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1386: error: for each function it appears in.)
error: 'IRQF_SHARED' undeclared (first use in this function)
error: implicit declaration of function 'free_irq'
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In this code, the failure_cleanup label calls the function
plx_pci_del_card, which frees everything in the card->net_dev array. dev
is placed in this array immediately after allocation, so the two subsequent
jumps to failure_cleanup should not also call free_sja1000dev, but the
second one does.
If plx_pci_check_sja1000 fails, then free_sja1000dev is also called on
dev. Because dev is already in the card->net_dev array, this implies that
when plx_pci_del_card is later called, it may get freed again. So that
entry is reset to NULL after the free.
Finally, if there is a problem with one channel, there will be a hole in the
array. card->channels counts the number of channels that have succeeded,
and does not keep track of the index of the largest element in the array
that is valid. So the loop in plx_pci_del_card is changed to go up to
PLX_PCI_MAX_CHAN, which is only 2.
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Boyer [Mon, 8 Aug 2011 02:34:07 +0000 (02:34 +0000)]
usbnet/cdc_ncm: Don't use stack variables for DMA
The cdc_ncm driver still has a few places where stack variables are
passed to the cdc_ncm_do_request function. This triggers a stack trace in
lib/dma-debug.c if the CONFIG_DEBUG_DMA_API option is set.
Adjust these calls to pass parameters that have been allocated with
kzalloc.
Signed-off-by: Josh Boyer <jwboyer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Sun, 7 Aug 2011 23:15:47 +0000 (23:15 +0000)]
vmxnet3: Don't enable vlan filters in promiscuous mode.
The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan. In promiscuous mode the filter table is cleared to in
order to disable filtering. However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it. As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.
CC: Scott J. Goldman <scottjg@vmware.com> CC: Shreyas Bhatewara <sbhatewara@vmware.com> CC: VMware PV-Drivers <pv-drivers@vmware.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Seungwon Jeon [Fri, 5 Aug 2011 03:35:03 +0000 (12:35 +0900)]
mmc: dw_mmc: Fix DDR mode support.
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Andy Shevchenko [Wed, 3 Aug 2011 15:36:01 +0000 (18:36 +0300)]
mmc: sdhci: use f_max instead of host->clock for timeouts
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Andy Shevchenko [Wed, 3 Aug 2011 15:35:59 +0000 (18:35 +0300)]
mmc: sdhci: check host->clock before using it as a denominator
Sometimes host->clock could be zero which is a legal situation. This
patch checks host->clock before usage as a denominator when timeout is
calculated. A similar patch is applied for mmc core (see commit e9b8684,
"mmc: fix division by zero in MMC core").
Without this patch, the execution of the sdhci_calc_timeout could end up
with a backtrace:
Reported-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c7764, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Fix below compile warning:
CC drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: dw_mmc: Fix mask in IDMAC_SET_BUFFER1_SIZE macro
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Andy Shevchenko [Fri, 22 Jul 2011 13:13:36 +0000 (16:13 +0300)]
mmc: mmc_test: avoid stalled file in debugfs
During card removal and inserting cycle the test file in the debugfs could be
stalled until the host driver removes it. Let's keep the file in the linked
list and destroy it when card is removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Per Forlin <per.forlin@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Aaron Lu [Mon, 11 Jul 2011 05:27:11 +0000 (13:27 +0800)]
mmc: sdhci: fix retuning timer wrongly deleted in sdhci_tasklet_finish
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.
Signed-off-by: Aaron Lu <Aaron.Lu@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Kalle Valo [Fri, 12 Aug 2011 18:45:44 +0000 (21:45 +0300)]
staging: remove ath6kl
ath6kl is now in drivers/net/wireless/ath so the staging driver
is not supported anymore and should be removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Greg KH <gregkh@suse.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug has been introduced by: d593411084a56124aa9d80aafa15db8463b2d8f7
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Mon Jul 11 10:48:51 2011 +0300
iwlagn: simplify the bus architecture
Revert part of the buggy patch: dev_get_drvdata will now return
iwl_priv as it did before the patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jiaying Zhang [Sat, 13 Aug 2011 16:17:13 +0000 (12:17 -0400)]
ext4: call ext4_ioend_wait and ext4_flush_completed_IO in ext4_evict_inode
Flush inode's i_completed_io_list before calling ext4_io_wait to
prevent the following deadlock scenario: A page fault happens while
some process is writing inode A. During page fault,
shrink_icache_memory is called that in turn evicts another inode
B. Inode B has some pending io_end work so it calls ext4_ioend_wait()
that waits for inode B's i_ioend_count to become zero. However, inode
B's ioend work was queued behind some of inode A's ioend work on the
same cpu's ext4-dio-unwritten workqueue. As the ext4-dio-unwritten
thread on that cpu is processing inode A's ioend work, it tries to
grab inode A's i_mutex lock. Since the i_mutex lock of inode A is
still hold before the page fault happened, we enter a deadlock.
Also moves ext4_flush_completed_IO and ext4_ioend_wait from
ext4_destroy_inode() to ext4_evict_inode(). During inode deleteion,
ext4_evict_inode() is called before ext4_destroy_inode() and in
ext4_evict_inode(), we may call ext4_truncate() without holding
i_mutex lock. As a result, there is a race between flush_completed_IO
that is called from ext4_ext_truncate() and ext4_end_io_work, which
may cause corruption on an io_end structure. This change moves
ext4_flush_completed_IO and ext4_ioend_wait from ext4_destroy_inode()
to ext4_evict_inode() to resolve the race between ext4_truncate() and
ext4_end_io_work during inode deletion.