Frank Blaschka [Thu, 12 May 2011 18:45:01 +0000 (18:45 +0000)]
qeth: convert to hw_features part 2
Set rx csum default to hw checksumming again.
Remove sysfs interface for rx csum (checksumming) and TSO (large_send).
With the new hw_features it does not work to keep the old sysfs
interface in parallel. Convert options.checksum_type to new hw_features.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Added code to take FW dump.
o Driver queries FW at the init time and gets the dump template
o It takes FW dump as per the dump template
o Level of FW dump (and its size) is configured via dump flag
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Thu, 12 May 2011 19:32:16 +0000 (19:32 +0000)]
be2net: fix mbox polling for signal reception
Sending mbox cmds require multiple steps of writing to the DB register and polling
for an ack. Gettting interrupted in the middle by a signal breaks the mbox protocol.
Use msleep() to not get interrupted.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Added code to take FW dump via ethtool. Dump level can be controlled via setting the
dump flag. A get function is provided to query the current setting of the dump flag.
Dump data is obtained from the driver via a separate get function.
Changes from v3:
Fixed buffer length issue in ethtool_get_dump_data function.
Updated kernel doc for ethtool_dump struct and get_dump_flag function.
Changes from v2:
Provided separate commands for get flag and data.
Check for minimum of the two buffer length obtained via ethtool and driver and
use that for dump buffer
Pass up the driver return error codes up to the caller.
Added kernel doc comments.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Orishko [Fri, 6 May 2011 03:01:30 +0000 (03:01 +0000)]
CDC NCM: Add mising short packet in cdc_ncm driver
Changes:
- while making NTB, driver shall check if device dwNtbOutMaxSize is higher than
host value and shall add a short packet if this is the case
- previous temporary patch for this issue is replaced by this one
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Tue, 10 May 2011 12:46:05 +0000 (12:46 +0000)]
ipvs: Remove all remaining references to rt->rt_{src,dst}
Remove all remaining references to rt->rt_{src,dst}
by using dest->dst_saddr to cache saddr (used for TUN mode).
For ICMP in FORWARD hook just restrict the rt_mode for NAT
to disable LOCALNODE. All other modes do not allow
IP_VS_RT_MODE_RDR, so we should be safe with the ICMP
forwarding. Using cp->daddr as replacement for rt_dst
is safe for all modes except BYPASS, even when cp->dest is
NULL because it is cp->daddr that is used to assign cp->dest
for sync-ed connections.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Sun, 8 May 2011 06:51:48 +0000 (06:51 +0000)]
tg3: Allow ethtool to enable/disable loopback.
This patch adds tg3_set_features() to handle loopback mode. Currently the
capability is added for the devices which support internal MAC loopback mode.
So when enabled, it enables internal-MAC loopback.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Virdi [Thu, 12 May 2011 01:04:40 +0000 (01:04 +0000)]
net/irda/ircomm_tty.c: Use flip buffers to deliver data
use tty_insert_flip_string and tty_flip_buffer_push to deliver incoming data
packets from the IrDA device instead of delivering the packets directly to the
line discipline. Following later approach resulted in warning "Sleeping function
called from invalid context".
Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Mon, 9 May 2011 11:53:27 +0000 (11:53 +0000)]
net: group FCoE related feature flags
Michał Mirosław's patch (http://patchwork.ozlabs.org/patch/94421/) fixes the
issue (http://patchwork.ozlabs.org/patch/94188/) about not populating FCoE related
flags correctly on vlan devices. However, only NETIF_F_FCOE_CRC is part of the
NETIF_F_ALL_TX_OFFLOADS right now, where weed NETIF_F_FCOE_MTU and NETIF_F_FSO
as well.
Therefore, add NETIF_F_ALL_FCOE to indicate feature flags used by FCoE TX offloads.
These include NETIF_F_FCOE_CRC, NETIF_F_FCOE_MTU, and NETIF_F_FSO and add them to
be part of NETIF_F_ALL_TX_OFFLOADS. This would eventually make sure all FCoE needed
flags are populated properly to vlan devices.
Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michał Mirosław [Fri, 6 May 2011 07:56:29 +0000 (07:56 +0000)]
net: Fix vlan_features propagation
Fix VLAN features propagation for devices which change vlan_features.
For this to work, driver needs to make sure netdev_features_changed()
gets called after the change (it is e.g. after ndo_set_features()).
Side effect is that a user might request features that will never
be enabled on a VLAN device.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Franco Fichtner <franco@lastsummer.de> Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 12 May 2011 21:46:56 +0000 (17:46 -0400)]
garp: remove last synchronize_rcu() call
When removing last vlan from a device, garp_uninit_applicant() calls
synchronize_rcu() to make sure no user can still manipulate struct
garp_applicant before we free it.
Use call_rcu() instead, as a step to further net_device dismantle
optimizations.
Add the temporary garp_cleanup_module() function to make sure no pending
call_rcu() are left at module unload time [ this will be removed when
kfree_rcu() is available ]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3: Use single tx queue when CONFIG_PCI_MSI not defined
Resending this patch with few changes.
Avoid multiple queues when MSI or MSI-X not available
Limit number of Tx queues to 1 if MSI/MSI-X support is not configured in
the kernel. This will make number of tx and rx queues equal when MSI/X
is not configured thus providing better performance.
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 11 May 2011 18:22:36 +0000 (18:22 +0000)]
l2tp: fix potential rcu race
While trying to remove useless synchronize_rcu() calls, I found l2tp is
indeed incorrectly using two of such calls, but also bumps tunnel
refcount after list insertion.
tunnel refcount must be incremented before being made publically visible
by rcu readers.
This fix can be applied to 2.6.35+ and might need a backport for older
kernels, since things were shuffled in commit fd558d186df2c
(l2tp: Split pppol2tp patch into separate l2tp and ppp parts)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com> CC: James Chapman <jchapman@katalix.com> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Start/stop TX queue is controlled by TX queue "used" counter.
It is incremented while WRBs are posted to TX queue and
decremented when TX completions are received. This counter was
getting decremented before HW is informed about processing of TX
completions. As used counter is decremented, transmit function
posts new WRBs and creates completion queue full scenario in HW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In Lancer if a frame is DMAed partially due to lack of RX buffers,
an error completion is sent with packet size as zero and num_recvd
indicating number of used buffers. These buffers need to be freed
and packet dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Tue, 10 May 2011 20:12:30 +0000 (13:12 -0700)]
slcan: fix ldisc->open retval
TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Mon, 9 May 2011 07:43:20 +0000 (07:43 +0000)]
net/usb: mark LG VL600 LTE modem ethernet interface as WWAN
Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm: Don't allow esn with disabled anti replay detection
Unlike the standard case, disabled anti replay detection needs some
nontrivial extra treatment on ESN. RFC 4303 states:
Note: If a receiver chooses to not enable anti-replay for an SA, then
the receiver SHOULD NOT negotiate ESN in an SA management protocol.
Use of ESN creates a need for the receiver to manage the anti-replay
window (in order to determine the correct value for the high-order
bits of the ESN, which are employed in the ICV computation), which is
generally contrary to the notion of disabling anti-replay for an SA.
So return an error if an ESN state with disabled anti replay detection
is inserted for now and add the extra treatment later if we need it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm: Assign the inner mode output function to the dst entry
As it is, we assign the outer modes output function to the dst entry
when we create the xfrm bundle. This leads to two problems on interfamily
scenarios. We might insert ipv4 packets into ip6_fragment when called
from xfrm6_output. The system crashes if we try to fragment an ipv4
packet with ip6_fragment. This issue was introduced with git commit ad0081e4 (ipv6: Fragment locally generated tunnel-mode IPSec6 packets
as needed). The second issue is, that we might insert ipv4 packets in
netfilter6 and vice versa on interfamily scenarios.
With this patch we assign the inner mode output function to the dst entry
when we create the xfrm bundle. So xfrm4_output/xfrm6_output from the inner
mode is used and the right fragmentation and netfilter functions are called.
We switch then to outer mode with the output_finish functions.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com> Reported-by: Einar EL Lueck <ELELUECK@de.ibm.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We should call vlan_gvrp_request_leave() from unregister_vlan_dev(),
not from vlan_dev_stop(), because vlan_gvrp_uninit_applicant()
is called right after unregister_netdevice_queue(). In batch mode,
unregister_netdevice_queue() doesn’t immediately call vlan_dev_stop().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 10 May 2011 03:55:03 +0000 (20:55 -0700)]
net: fix two lockdep splats
Commit e67f88dd12f6 (net: dont hold rtnl mutex during netlink dump
callbacks) switched rtnl protection to RCU, but we forgot to adjust two
rcu_dereference() lockdep annotations :
inet_get_link_af_size() or inet_fill_link_af() might be called with
rcu_read_lock or rtnl held, so use rcu_dereference_rtnl()
instead of rtnl_dereference()
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 May 2011 22:13:28 +0000 (15:13 -0700)]
ipv4: xfrm: Eliminate ->rt_src reference in policy code.
Rearrange xfrm4_dst_lookup() so that it works by calling a helper
function __xfrm_dst_lookup() that takes an explicit flow key storage
area as an argument.
Use this new helper in xfrm4_get_saddr() so we can fetch the selected
source address from the flow instead of from rt->rt_src
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 May 2011 20:28:22 +0000 (13:28 -0700)]
ipv4: icmp: Eliminate remaining uses of rt->rt_src
On input packets, rt->rt_src always equals ip_hdr(skb)->saddr
Anything that mangles or otherwise changes the IP header must
relookup the route found at skb_rtable(). Therefore this
invariant must always hold true.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Fri, 22 Apr 2011 01:34:03 +0000 (20:34 -0500)]
tipc: Revise timings used when sending link request messages
Revises the algorithm governing the sending of link request messages
to take into account the number of nodes each bearer is currently in
contact with, and to ensure more rapid rediscovery of neighboring nodes
if a bearer fails and then recovers.
The discovery object now sends requests at least once a second if it
is not in contact with any other nodes, and at least once a minute if
it has at least one neighbor; if contact with the only neighbor is
lost, the object immediately reverts to its initial rapid-fire search
timing to accelerate the rediscovery process.
In addition, the discovery object now stops issuing link request
messages if it is in contact with the only neighboring node it is
configured to communicate with, since further searching is unnecessary.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 21 Apr 2011 21:28:02 +0000 (16:28 -0500)]
tipc: Enhance sending of discovery object link request messages
Augments TIPC's discovery object to send its initial neighbor discovery
request message as soon as the associated bearer is created, rather than
waiting for its first periodic timeout to occur, thereby speeding up the
discovery process. Also adds a check to suppress the initial request or
subsequent requests if the bearer is blocked at the time the request is
scheduled for transmission.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 21 Apr 2011 18:58:26 +0000 (13:58 -0500)]
tipc: Enhance handling of discovery object creation failures
Modifies bearer creation and deletion code to improve handling of
scenarios when a neighbor discovery object cannot be created. The
creation routine now aborts the creation of a bearer if its discovery
object cannot be created, and deletes the newly created bearer, rather
than failing quietly and leaving an unusable bearer hanging around.
Since the exit via the goto label really isn't a definitive failure
in all cases, relabel it appropriately.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 21 Apr 2011 15:50:42 +0000 (11:50 -0400)]
tipc: Introduce routine to enqueue a chain of messages on link tx queue
Create a helper routine to enqueue a chain of sk_buffs to a link's
transmit queue. It improves readability and the new function is
anticipated to be used more than just once in the future as well.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 21 Apr 2011 15:42:07 +0000 (10:42 -0500)]
tipc: Avoid recomputation of outgoing message length
Rework TIPC's message sending routines to take advantage of the total
amount of data value passed to it by the kernel socket infrastructure.
This change eliminates the need for TIPC to compute the size of outgoing
messages itself, as well as the check for an oversize message in
tipc_msg_build(). In addition, this change warrants an explanation:
- res = send_packet(NULL, sock, &my_msg, 0);
+ res = send_packet(NULL, sock, &my_msg, bytes_to_send);
Previously, the final argument to send_packet() was ignored (since the
amount of data being sent was recalculated by a lower-level routine)
and we could just pass in a dummy value (0). Now that the
recalculation is being eliminated, the argument value being passed to
send_packet() is significant and we have to supply the actual amount
of data we want to send.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Tue, 20 Apr 2010 21:58:24 +0000 (17:58 -0400)]
tipc: Abort excessive send requests as early as possible
Adds checks to TIPC's socket send routines to promptly detect and
abort attempts to send more than 66,000 bytes in a single TIPC
message or more than 2**31-1 bytes in a single TIPC byte stream request.
In addition, this ensures that the number of iovecs in a send request
does not exceed the limits of a standard integer variable.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Wed, 20 Apr 2011 21:24:07 +0000 (16:24 -0500)]
tipc: Strengthen checks for neighboring node discovery
Enhances existing checks on the discovery domain associated with a TIPC
bearer. A bearer can no longer be configured to accept links from itself
only (which would be pointless), or to nodes outside its own cluster
(since multi-cluster support has now been removed from TIPC). Also, the
neighbor discovery routine now validates link setup requests against the
configured discovery domain for the bearer, rather than simply ensuring
the requesting node belongs to the node's own cluster.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Tue, 19 Apr 2011 14:17:58 +0000 (10:17 -0400)]
tipc: Fix sk_buff leaks when link congestion is detected
Modifies a TIPC send routine that did not discard the outgoing sk_buff
if it was not transmitted because of link congestion; this eliminates
the potential for buffer leakage in the many callers who did not clean up
the unsent buffer. (The two routines that previously did discard the unsent
buffer have been updated to eliminate their now-redundant clean up.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Mon, 18 Apr 2011 14:14:26 +0000 (10:14 -0400)]
tipc: Update destination node field on incoming multicast messages
Sets the destination node field of an incoming multicast message
to the receiving node's network address before handing off the message
to each receiving port. This ensures that, in the event the destination
port returns the message to the sender, the sender can identify which
node the destination port belonged to.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Mon, 18 Apr 2011 14:08:22 +0000 (10:08 -0400)]
tipc: Fix problem with bundled multicast message
Set the destination node and destination port fields of an outgoing
multicast message header to zero; this is necessary to ensure that
the receiving node can route the message properly if it was packed
into a bundle due to link congestion. (Previously, there was a chance
that the receiving node would send the unbundled message to a random
node & port, rather than processing the message itself.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Sun, 17 Apr 2011 20:02:11 +0000 (16:02 -0400)]
tipc: Set name lookup scope field properly in all data messages
Ensures that all outgoing data messages have the "name lookup scope"
field of their header set correctly; that is, named multicast messages
now specify cluster-wide name lookup, while messages not using TIPC
naming zero out the lookup field. (Previously, the lookup scope specified
for these types of messages was inherited from the last message sent
by the sending port.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Sun, 17 Apr 2011 17:06:23 +0000 (13:06 -0400)]
tipc: Fix issues with fragmentation of an existing message buffer
Modifies the routine that fragments an existing message buffer to
use similar logic to that used when generating fragments from an iovec.
The routine now creates a complete chain of fragments and adds them to
the link transmit queue as a unit, so that the link sends all fragments
or none; this prevents the incomplete transmission of a fragmented
message that might otherwise result because of link congestion or
memory exhaustion. This change also ensures that the counter recording
the number of fragmented messages sent by the link is now incremented
only if the message is actually sent.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Sun, 17 Apr 2011 15:44:24 +0000 (11:44 -0400)]
tipc: Avoid pointless masking of fragmented message identifier
Eliminates code that restricts a link's counter of its fragmented
messages to a 16-bit value, since the counter value is automatically
restricted to this range when it is written into the message header.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Sun, 17 Apr 2011 14:29:16 +0000 (10:29 -0400)]
tipc: Don't initialize link selector field in fragmented messages
Eliminates code that sets the link selector field in the header of
fragmented messages, since this information is never referenced.
(The unnecessary initialization was harmless as it was over-written
by the fragmented message identifier value before the fragments were
transmitted.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Tue, 12 Apr 2011 18:59:03 +0000 (14:59 -0400)]
tipc: Remove code to emulate loss of broadcast messages
Eliminates optional code used to test TIPC's ability to recover
from lost broadcast messages. This code duplicates functionality
already provided by the network stack's QoS option "network emulator".
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Fri, 8 Apr 2011 15:04:15 +0000 (11:04 -0400)]
tipc: Cosmetic consolidation of internal message type definitions
Half of the #define entries in msg.h were down at the bottom
of the header, instead of up at the top before any of the static
inlines etc. Relocate them up to the top, to be consistent with
the other normal linux header file layout conventions.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of unused constants defining the types used in routing
messages. These messages no longer exist in TIPC now that multicluster
and multizone support has been eliminated.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Fri, 8 Apr 2011 14:50:52 +0000 (10:50 -0400)]
tipc: Update comments in message header include file
Removes comments in TIPC's message header include file that are
outdated and/or unnecessary. Also introduces short comments (or
supplements existing ones) to better describe several set of existing
symbolic constants.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Michal Marek [Tue, 5 Apr 2011 14:59:16 +0000 (16:59 +0200)]
tipc: Drop __TIME__ usage
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: netdev@vger.kernel.org Cc: tipc-discussion@lists.sourceforge.net Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Florian Wesphal says:
"... when the packet was sent from the local machine the skb
already has ->nfct attached, and -m conntrack seems to do
the right thing."
Acked-by: Jan Engelhardt <jengelh@medozas.de> Reported-by: Florian Wesphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: IPv6: initialize TOS field in REJECT target module
The IPv6 header is not zeroed out in alloc_skb so we must initialize
it properly unless we want to see IPv6 packets with random TOS fields
floating around. The current implementation resets the flow label
but this could be changed if deemed necessary.
We stumbled upon this issue when trying to apply a mangle rule to
the RST packet generated by the REJECT target module.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
DESCRIPTION
This patch tries to restore the initial init and cleanup
sequences that was before namspace patch.
Netns also requires action when net devices unregister
which has never been implemented. I.e this patch also
covers when a device moves into a network namespace,
and has to be released.
IMPLEMENTATION
The number of calls to register_pernet_device have been
reduced to one for the ip_vs.ko
Schedulers still have their own calls.
This patch adds a function __ip_vs_service_cleanup()
and an enable flag for the netfilter hooks.
The nf hooks will be enabled when the first service is loaded
and never disabled again, except when a namespace exit starts.
Signed-off-by: Hans Schillstrom <hans@schillstrom.com> Acked-by: Julian Anastasov <ja@ssi.bg>
[horms@verge.net.au: minor edit to changelog] Signed-off-by: Simon Horman <horms@verge.net.au>
IPVS: Change of socket usage to enable name space exit.
If the sync daemons run in a name space while it crashes
or get killed, there is no way to stop them except for a reboot.
When all patches are there, ip_vs_core will handle register_pernet_(),
i.e. ip_vs_sync_init() and ip_vs_sync_cleanup() will be removed.
Kernel threads should not increment the use count of a socket.
By calling sk_change_net() after creating a socket this is avoided.
sock_release cant be used intead sk_release_kernel() should be used.
Thanks Eric W Biederman for your advices.
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
[horms@verge.net.au: minor edit to changelog] Signed-off-by: Simon Horman <horms@verge.net.au>
netfilter: ebtables: only call xt_compat_add_offset once per rule
The optimizations in commit 255d0dc34068a976
(netfilter: x_table: speedup compat operations) assume that
xt_compat_add_offset is called once per rule.
ebtables however called it for each match/target found in a rule.
The match/watcher/target parser already returns the needed delta, so it
is sufficient to move the xt_compat_add_offset call to a more reasonable
location.
While at it, also get rid of the unused COMPAT iterator macros.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Patrick McHardy <kaber@trash.net>
Eric Dumazet [Thu, 21 Apr 2011 08:57:21 +0000 (10:57 +0200)]
netfilter: fix ebtables compat support
commit 255d0dc34068a976 (netfilter: x_table: speedup compat operations)
made ebtables not working anymore.
1) xt_compat_calc_jump() is not an exact match lookup
2) compat_table_info() has a typo in xt_compat_init_offsets() call
3) compat_do_replace() misses a xt_compat_init_offsets() call
Reported-by: dann frazier <dannf@dannf.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
Tomoya [Mon, 9 May 2011 01:19:37 +0000 (01:19 +0000)]
pch_gbe: support ML7223 IOH
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Sat, 7 May 2011 23:00:07 +0000 (23:00 +0000)]
net: add mac_pton() for parsing MAC address
mac_pton() parses MAC address in form XX:XX:XX:XX:XX:XX and only in that form.
mac_pton() doesn't dirty result until it's sure string representation is valid.
mac_pton() doesn't care about characters _after_ last octet,
it's up to caller to deal with it.
mac_pton() diverges from 0/-E return value convention.
Target usage:
if (!mac_pton(str, whatever->mac))
return -EINVAL;
/* ->mac being u8 [ETH_ALEN] is filled at this point. */
/* optionally check str[3 * ETH_ALEN - 1] for termination */
Use mac_pton() in pktgen and netconsole for start.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8169: merge firmware information into the chipset description data.
- RTL_GIGA_MAC_NONE is a fake index so put it at the end of the
enumeration and shift everybody.
- RTL_GIGA_MAC_VER_17 / RTL_GIGA_MAC_VER_16 ordering fixed. Though
not wrong it was confusing enough to wonder if things were right.
Renaming rtl_chip_info was not strictly necessary. It allows to
check the patch for the correct use of the indexes though.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Francois Romieu [Tue, 15 Mar 2011 16:29:31 +0000 (17:29 +0100)]
r8169: remove non-NAPI context invocation of rtl8169_rx_interrupt.
Invocation of rtl8169_rx_interrupt from rtl8169_reset_task was originally
intended to retrieve as much packets as possible from the rx ring when a
reset was needed. Nowadays rtl8169_reset_task is only scheduled, with
some delay
a. from the tx timeout watchdog
b. when resuming
c. from rtl8169_rx_interrupt itself
It's dubious that the loss of outdated packets will matter much for a)
and b). c) does not need to call itself again.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Francois Romieu [Fri, 11 Mar 2011 20:07:11 +0000 (21:07 +0100)]
r8169: link speed selection timer rework.
The implementation was a bit krusty.
The 10s rtl8169_phy_timer timer has been (was ?) required with older
8169 for adequate phy operation when full gigabit is advertised in
autonegotiated mode. The timer does nothing if the link is up.
Otherwise it keeps resetting the phy until things improve.
- the device private data field phy_1000_ctrl_reg was used to
schedule the timer. Avoid it and save a few bytes.
- rtl8169_set_settings
pending timer is disabled before changing the link settings as
rtl8169_phy_timer is not always needed (see the removed test in
rtl8169_phy_timer).
- rtl8169_set_speed
the requested link parameters may not match the chipset : bail out
early on failure.
- rtl8169_open
Calling rtl8169_request_timer is redundant with
-> rtl8169_open
-> rtl8169_init_phy
-> rtl8169_set_speed
-> mod_timer
The latter always enables the phy timer whereas the former did not
for RTL_GIGA_MAC_VER_01. It should not make things worse but only
time will tell if reality agrees.
- rtl8169_request_timer : unused yet. Removed.
- rtl8169_delete_timer : useless. Bloat. Removed.
Side effect : the timer may kick in if the TBI is enabled. I do not
know if the TBI has ever been used in real life.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Francois Romieu [Fri, 11 Mar 2011 19:30:24 +0000 (20:30 +0100)]
r8169: rtl8169_set_speed_xmii cleanup.
Shorten chipset version test.
No functional change.
Careful readers will notice that the 'supports_gmii' flag is deduced
from the device PCI id. Though less specific than the chipset related
RTL_GIGA_MAC_VER_XY, it is good enough to detect a GMII deprieved 810x.
Some features push for a device specific configuration (improved jumbo
frame support for instance). 'supports_gmii' will follow this path
if / when the device PCI id test stops working.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Toshiharu Okada [Fri, 6 May 2011 02:53:51 +0000 (02:53 +0000)]
PCH_GbE : Fixed the issue of collision detection
The collision detection setting was invalid.
When collision occurred, because data was not resent,
there was an issue to which a transmitting throughput falls.
This patch enables the collision detection.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
TTY layer expects 0 if the ldisc->open operation succeeded.
Signed-off-by : Matvejchikov Ilya <matvejchikov@gmail.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Wed, 4 May 2011 22:40:46 +0000 (22:40 +0000)]
be2net: Fixed bugs related to PVID.
Fixed bug to make sure 'pvid' retrieval will work on big endian hosts.
Fixed incorrect comparison between the Rx Completion's 16-bit VLAN TCI
and the PVID. Now comparing only the relevant 12 bits corresponding to
the VID.
Renamed 'vid' field under Rx Completion to 'vlan_tag' to reflect
accurate description.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>