ARM: dts: imx35-pdk: Fix memory region description

On imx35pdk there are two DRAM chip selects that are used:

CS0 at 0x80000000
CS1 at 0x90000000

Each bank is connected to 128MB of DRAM, giving a total of 256MB of system DRAM.

Fix the memory layout to describe the hardware appropriately.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-eukrea-mbimxsd51-baseboard: Add CAN support

Add support for CAN based on a MCP2515 connected to ECSPI1.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6: add new board RIoTboard

add element14s RIoTboard http://www.riotboard.org which is an i.MX6Solo
based design targeted at makers.

Signed-off-by: Iain Paton<ipaton0@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6: i2c4 cleanup

add missing i2c4 clock and correct the compatible string to match other
imx6 i2c blocks

Signed-off-by: Iain Paton<ipaton0@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6: edmqmx6: add vcc and vio power supplies to stmpe

Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Karo TX25: use hardware ecc

We should use hardware ecc on i.MX. While at it, add the optional
nand-bus-width property.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Karo TX25: Add phy reset gpio and supply for FEC

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Karo TX25: Add pinctrl nodes

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX25: Add IRAM node

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX25: Add mmc aliases

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX51 babbage: Fix FEC pad ctrl settings

The dts relied on the FEC pad ctrl settings from the bootloader by
using the NO_PAD_CTRL option. This breaks once the bootloader starts
initializing the pad ctrl settings from the same dts file. Change
to real pad ctrl settings taken from the platform based babbage
support.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-sabresd: Add USDHC4 support

USDHC4 is connected to a DDR MMC. Add support for it.

Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: imx: add HDMI support for SolidRun HummingBoard and Cubox-i

Add the HDMI DT configuration for the SolidRun HummingBoard and Cubox-i.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6: edmqmx6: add SPI bus and flash

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6: edmqmx6: add pinctrl for pfuze irq gpio

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6q-udoo: Add HDMI support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Add stdout-path property to i.MX boards

This adds the stdout-path property to various i.MX boards. Values
of the property have been taken from barebox, so they should be
correct. Also, the older linux,stdout-path property is converted
to stdout-path.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx: Fix LVDS mapping for Ventana GW52xx

The GW52xx supports LVDS on channel 0. Remove the obsolete crtcs node and
add display timings for the HanStar HSD100PXN1 display.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx: add LVDS backlight for Ventana

The GW54xx/GW53xx/GW52xx all support LVDS with a PWM controlled backlight.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-sabresd: remove power-on gpio from pcie

This isn't compatible with the new binding and should be
handled via a proper regulator. It shouldn't be needed as
the driver has always ignored this property.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6: update pcie to bring in line with new binding

The new bindings drops one clock, renames the others and
drops the old interrupt mapping.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx53-qsb-common: Add TVE support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Fix "reg" property for USBH2 PHY

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Add CSI enable switch

This patch adds a GPIO fixed regulator which used on RDK to
enable CSI bus.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx: Remove excess entries for PMIC

This patch removes excess "#address-cells" and "#size-cells" entries
for PMIC, since these entries is not used.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-som: Disable PM pins for USB OTG

USB PWR and OC pins are used as GPIOs for different purposes,
so add "disable-over-current" property for OTG node to indicate this.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-som: Fix active level for FEC reset

FEC reset GPIO is active low. Fix this typo.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Remove duplicate entries for USB PHY

"compatible", "#address-cells" and "#size-cells" for USB PHY are
already described in the SOM DTS. Remove these duplicate entries.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: ventana: Add HDMI support

Configure ddc and enable HDMI

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-sabresd: Add PCIe support

Add support for the PCI express bus available on MX6 SabreSDP.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-wandboard: Add HDMI support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6qdl-sabresd: Add HDMI support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Add keypad support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Add NAND support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx6q-gk802: Enable HDMI

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Add USB OTG support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27: Place the usb phy nodes in the board dts files

It is not a good approach to have the USB PHY nodes inside imx27.dtsi since
the USB PHYs on mx27 are not internal to the SoC.

Place the USB PHY nodes in the board dts files instead.

Also, each board may have a different clock source for the USB PHY, so do not
hardcode it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27: Use the correct usb clock gate

USB Host1, Host2 and OTG are gated via 'usb_ipg_gate' clock, so fix it in order
to avoid the following kernel oops:

usbcore: registered new interface driver usb-storage
10024000.usb supply vbus not found, using dummy regulator
Unhandled fault: external abort on non-linefetch (0x808) at 0xf4424184
Internal error: : 808 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.0-rc1-26325-g971f9fd-dirty #64
task: c7829aa0 ti: c7836000 task.ti: c7836000
PC is at ci_hdrc_probe+0x3a4/0x634
LR is at ci_hdrc_probe+0x100/0x634
pc : [<c036cc78>]    lr : [<c036c9d4>]    psr: 60000013
sp : c7837d48  ip : 00000001  fp : 00000000
r10: 00000000  r9 : 00000000  r8 : c791b6c0
r7 : c7945000  r6 : f4424000  r5 : c7945010  r4 : c794e010
r3 : f4424184  r2 : 00000000  r1 : 8c000004  r0 : 0c000004
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 0005317f  Table: a0004000  DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc78361c0)
Stack: (0xc7837d48 to 0xc7838000)

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-som: Move PMIC IRQ GPIO into a separate pin group

The hardware is better described if we place the PMIC IRQ GPIO into its own
pingroup.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Add PMIC support

imx27-pdk has a MC13783 PMIC connected to CSPI2 port.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Use predefined constants for clock definition

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add devicetree node for I2C1

This patch adds devicetree node and pinctrl group for I2C1.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Sort nodes by name

This patch sorts nodes by name and moves "iomux" configuration at
the bottom of file.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add USB OTG regulator node

This patch adds a regulator node and pinctrl group for USB OTG.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Use predefined constants for keys definition

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add missing pingroup for PMIC

This patch adds missing pin definition for PMIC IRQ GPIO.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Move "hog" pins into corresponded pin groups

Move "hog" pins into corresponded pin groups for eSDHC1, eSDHC2,
eCSPI1, gpio-keys, regulator-fixed and codec clock.
Additionally, this patch fixes GPIO active level definition for
USB regulator.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX51: Allow to define partitions onto NFC

This patch allow to define partitions onto NFC in user defined
devicetrees.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Enable DVI

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Enable UART1

This patch enables UART1 on the phyFLEX connector (i.MX6 uart3).

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pfla02: Add UART1 (uart3)

The pins labeled UART1 on the module connector are wired to i.MX6 uart3.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Add I2C devices

This patch adds the TLV320, STMPE811, RTC8564, and MX1037 ICs to the I2C2 bus.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Add I2C2 and I2C3

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pbab01: Set linux,stdout-path to UART4

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pfla02: PHY reset is active-low

Note that the fec driver code currently hard-codes an active-low
reset, regardless of the flags in the device tree.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: pfla02: Add GPIO LEDs

This patch enables the red and green GPIO LEDs on Phytec phyFLEX i.MX6 modules.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Add Phytec pbab01 with i.MX6 DualLite/Solo

The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo
phyFLEX i.MX6 modules (PFL-A-02).
This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific
device trees then just include the pfla01 and pbab01 dtsi files corresponding
to the SoC variant.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Pass the FEC pin configuration

Provide an entry for the FEC pin muxing.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Pass the UART1 pin configuration

Provide an entry for the UART1 pin muxing.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Keep the dt nodes sorted

For better readability keep the dt nodes sorted.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM i.MX51: Add Digi ConnectCore devicetree

This patch adds support for Digi ConnectCore® i.MX51/Wi-i.MX51 SOM
and basic support for the ConnectCore for i.MX51 JumpStart Kit.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX: Use single naming style for i.MX WEIM device

This patch converts all i.MX WEIM users to use single naming style
for devices.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: cpuimx51 Add touchscreen support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: cpuimx35 Add touchscreen support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mbimxsd51 baseboard: Add USB support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: add initial Colibri VF61 board support

Add initial Toradex Colibri VF61 board support. Ethernet, UART
and SDHC cards are working. Cache latencies need to be a bit
higher than vf610.dtsi suggests. Those values are validated
by running multiple memory tests.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

of: add vendor prefix for Toradex AG

Adds toradex to the list of DT vendor prefixes.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-pdk: Pass the memory range

imx27-pdk has 128 MB of DRAM. Pass the memory range in dt.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Add display control signal definitions

This patch adds display control signal definitions.
These fields are not used in the driver yet, but will be used for
reference to indicate the polarity of the signals.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx28-duckbill: use symbolic names from gpio.h

Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx28-duckbill: fix phy reset gpio

Fix a copy & paste error: on duckbills the GPIO used for resetting
the ethernet phy differs from FSL's MX28EVK board.

Reported-by: Stefan Wahren <info@lategoodbye.de>
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx28: include gpio.h to allow use of symbolic names

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx28-duckbill: fix mmc settings

I2SE's duckbills are only equipped with a micro SD card slot and
thus only provide a 4-bit interface.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add USB OTG support

Tested by pinging from the host PC to the imx51-babbage via a g_ether
connection.

Signed-off by: Dave Ebright <dave.ebright@parsons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx51-babbage: Add USB Host1 support

Signed-off by: Dave Ebright <dave.ebright@parsons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx35-pdk: Add initial device tree support

Add support for UART, eSDHC and NAND.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: vf610-twr: Enables FTM PWM device.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: vf610-twr: Add PWM0's pinctrl node

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: vf610: Add Freescale FTM PWM node.

This adds devicetree node for VF610, and there are 8 channels
supported.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX53: Add reset line to VPU device node

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX53: Enable CODA7541 VPU

This IP module is always present and has no external connections.
There is no reason to disable it in the device tree.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25-pdk: Add USB Host1 support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx27-phytec-phycore-rdk: Add display support

This patch adds FB, Sharp-LQ035Q7 display (add-on module) and
corresponded pinctrl devicetree nodes to the Phytec PCM970 RDK.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25-pdk: Add CAN support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25-pdk: Add keypad support

Tested with evtest.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25-pdk: Add audio support

mx25pdk has a sgtl5000 codec connected to the I2C1 port.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mbimxsd35 baseboard: Add USB support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: i.MX35: Add USB support.

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mbimxsd25 baseboard: Add USB support

Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: imx25.dtsi: Fix USB support.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mx35: USB block requires only one clock

Like other imx SoCs only one USB clock is needed on mx35.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: mx25: USB block requires only one clock

Like other imx SoCs only one USB clock is needed on mx25.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

ARM: dts: vf610-twr: Add support for sdhc1

The kernel was not able to boot from SD card because sdhc support
was not present into the dts.

A new entry for sdhc1 was added for vf610-twr board based on the
compatible entry present on imx53.

After applying these changes, the kernel is able to boot successfully
from SD card.

Signed-off-by: Cosmin Stoica <cosminstefan.stoica@freescale.com>
Signed-off-by: Chircu Bogdan <Bogdan.Chircu@freescale.com>
Signed-off-by: Eddy Petrisor <eddy.petrisor@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Add esdhc1 support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Provide an Ethernet PHY reset

GPIO4_8 is connected to the Ethernet PHY reset line, so populate the
'phy-reset-gpios' property accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Provide a regulator for Ethernet PHY

GPIO2_3 controls the power to the Ethernet PHY, so provide a regulator node
for this.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Add FEC pins

Instead of relying on the bootloader for configuring the FEC pins, pass the
FEC pin configuration via device tree instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Add UART1 pins

UART1 is the console port on mx25pdk board.

Add the pin configuration for UART1 port and also pass 'fsl,uart-has-rtscts'
to indicate that the port has RTS and CTS pins.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx25-pdk: Sort the dt nodes

Keep the dt nodes sorted for better readability.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>