Johan Hovold [Wed, 19 Nov 2014 11:59:21 +0000 (12:59 +0100)]
dt/bindings: add clock-select function property to micrel phy binding
Add "micrel,rmii-reference-clock-select-25-mhz" to Micrel ethernet PHY
binding documentation.
This property is needed to properly describe some revisions of Micrel
PHYs which has the function of this configuration bit inverted so that
setting it enables 25 MHz rather than 50 MHz clock mode.
Note that a clock reference ("rmii-ref") is still needed to actually
select either mode.
Cc: devicetree@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Wed, 19 Nov 2014 11:59:19 +0000 (12:59 +0100)]
net: phy: micrel: add support for clock-mode select to KSZ8081/KSZ8091
Micrel KSZ8081 and KSZ8091 PHYs have the RMII Reference Clock Select
bit, which is used to select 25 or 50 MHz clock mode.
Note that on some revisions of the PHY (e.g. KSZ8081RND) the function of
this bit is inverted so that setting it enables 25 rather than 50 MHz
mode. Add a new device-tree property
"micrel,rmii-reference-clock-select-25-mhz" to describe this.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Wed, 19 Nov 2014 11:59:18 +0000 (12:59 +0100)]
net: phy: micrel: add generic clock-mode-select support
Add generic RMII-Reference-Clock-Select support.
Several Micrel PHY have an RMII-Reference-Clock-Select bit to select
25 MHz or 50 MHz clock mode. Recently, support for configuring this
through device tree for KSZ8021 and KSZ8031 was added.
Generalise this support so that it can be configured for other PHY types
as well.
Note that some PHY revisions (of the same type) has this bit inverted.
This should be either configurable through a new device-tree property,
or preferably, determined based on PHY ID if possible.
Also note that this removes support for setting 25 MHz mode from board
files which was also added by the above mentioned commit 45f56cb82e45
("net/phy: micrel: Add clock support for KSZ8021/KSZ8031").
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Morris <ipm@chirality.org.uk> Cc: Mirko Lindner <mlindner@marvell.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Check and update posted_index only when skb->xmit_more is 0 or tx queue is full.
v2:
use txq_map instead of skb_get_queue_mapping(skb)
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Nov 2014 00:10:17 +0000 (19:10 -0500)]
Merge branch 'bonding_4ad'
Xie Jianhua says:
====================
bonding: Introduce 4 AD link speed
The speed field of AD Port Key was based on bitmask, it supported 5
kinds of link speed at most, as there were only 5 bits in the speed
field of the AD Port Key. This patches series change the speed type
(AD_LINK_SPEED_BITMASK) from bitmask to enum type in order to enhance
speed type from 5 to 32, and then introduce 4 AD link speed to fix
agg_bandwidth.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jianhua Xie [Wed, 19 Nov 2014 08:48:59 +0000 (16:48 +0800)]
bonding: Introduce 4 AD link speed to fix agg_bandwidth
This patch adds [2.5|20|40|56] Gbps enum definition, and fixes
aggregated bandwidth calculation based on above slave links.
CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: David S. Miller <davem@davemloft.net> Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jianhua Xie [Wed, 19 Nov 2014 08:48:58 +0000 (16:48 +0800)]
bonding: change AD_LINK_SPEED_BITMASK to enum to suport more speed
Port Key was determined as 16 bits according to the link speed,
duplex and user key (which is yet not supported). In the old
speed field, 5 bits are for speed [1|10|100|1000|10000]Mbps as
below:
--------------------------------------------------------------
Port key :| User key | Speed | Duplex|
--------------------------------------------------------------
16 6 1 0
This patch keeps the old layout, but changes AD_LINK_SPEED_BITMASK
from bit type to an enum type. In this way, the speed field can
expand speed type from 5 to 32.
CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: David S. Miller <davem@davemloft.net> Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Mon, 10 Nov 2014 03:33:45 +0000 (22:33 -0500)]
{compat_,}verify_iovec(): switch to generic copying of iovecs
use {compat_,}rw_copy_check_uvector(). As the result, we are
guaranteed that all iovecs seen in ->msg_iov by ->sendmsg()
and ->recvmsg() will pass access_ok().
Al Viro [Sun, 6 Apr 2014 18:03:05 +0000 (14:03 -0400)]
separate kernel- and userland-side msghdr
Kernel-side struct msghdr is (currently) using the same layout as
userland one, but it's not a one-to-one copy - even without considering
32bit compat issues, we have msg_iov, msg_name and msg_control copied
to kernel[1]. It's fairly localized, so we get away with a few functions
where that knowledge is needed (and we could shrink that set even
more). Pretty much everything deals with the kernel-side variant and
the few places that want userland one just use a bunch of force-casts
to paper over the differences.
The thing is, kernel-side definition of struct msghdr is *not* exposed
in include/uapi - libc doesn't see it, etc. So we can add struct user_msghdr,
with proper annotations and let the few places that ever deal with those
beasts use it for userland pointers. Saner typechecking aside, that will
allow to change the layout of kernel-side msghdr - e.g. replace
msg_iov/msg_iovlen there with struct iov_iter, getting rid of the need
to modify the iovec as we copy data to/from it, etc.
We could introduce kernel_msghdr instead, but that would create much more
noise - the absolute majority of the instances would need to have the
type switched to kernel_msghdr and definition of struct msghdr in
include/linux/socket.h is not going to be seen by userland anyway.
This commit just introduces user_msghdr and switches the few places that
are dealing with userland-side msghdr to it.
[1] actually, it's even trickier than that - we copy msg_control for
sendmsg, but keep the userland address on recvmsg.
bpf: fix arraymap NULL deref and missing overflow and zero size checks
- fix NULL pointer dereference:
kernel/bpf/arraymap.c:41 array_map_alloc() error: potential null dereference 'array'. (kzalloc returns null)
kernel/bpf/arraymap.c:41 array_map_alloc() error: we previously assumed 'array' could be null (see line 40)
- integer overflow check was missing in arraymap
(hashmap checks for overflow via kmalloc_array())
- arraymap can round_up(value_size, 8) to zero. check was missing.
- hashmap was missing zero size check as well, since roundup_pow_of_two() can
truncate into zero
- found a typo in the arraymap comment and unnecessary empty line
Fix all of these issues and make both overflow checks explicit U32 in size.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Recently many changes have been done inside the driver
so this patch updates the driver's doc for example reviewing
information for the rx and tx processes that are managed
by napi method, adding new information for missing glue-logic files
etc.
Also this reviews and fixes what is reported when run kernel-doc script.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently many changes have been done inside the driver
so this patch updates the driver's doc for example reviewing
information for the rx and tx processes that are managed
by napi method, adding new information for missing glue-logic files
etc.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 18 Nov 2014 07:06:20 +0000 (23:06 -0800)]
tcp: make connect() mem charging friendly
While working on sk_forward_alloc problems reported by Denys
Fedoryshchenko, we found that tcp connect() (and fastopen) do not call
sk_wmem_schedule() for SYN packet (and/or SYN/DATA packet), so
sk_forward_alloc is negative while connect is in progress.
We can fix this by calling regular sk_stream_alloc_skb() both for the
SYN packet (in tcp_connect()) and the syn_data packet in
tcp_send_syn_data()
Then, tcp_send_syn_data() can avoid copying syn_data as we simply
can manipulate syn_data->cb[] to remove SYN flag (and increment seq)
Instead of open coding memcpy_fromiovecend(), simply use this helper.
This leaves in socket write queue clean fast clone skbs.
This was tested against our fastopen packetdrill tests.
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 18 Nov 2014 05:20:41 +0000 (13:20 +0800)]
tun: return NET_XMIT_DROP for dropped packets
After commit 5d097109257c03a71845729f8db6b5770c4bbedc
("tun: only queue packets on device"), NETDEV_TX_OK was returned for
dropped packets. This will confuse pktgen since dropped packets were
counted as sent ones.
Fixing this by returning NET_XMIT_DROP to let pktgen count it as error
packet.
Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Jones [Mon, 17 Nov 2014 22:04:29 +0000 (14:04 -0800)]
icmp: Remove some spurious dropped packet profile hits from the ICMP path
If icmp_rcv() has successfully processed the incoming ICMP datagram, we
should use consume_skb() rather than kfree_skb() because a hit on the likes
of perf -e skb:kfree_skb is not called-for.
Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Nov 2014 20:24:53 +0000 (15:24 -0500)]
Merge tag 'linux-can-next-for-3.19-20141117' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull request of 9 patches for net-next/master.
All 9 patches are by Roger Quadros and update the c_can platform
driver. First by improving the initialization sequence of the message
RAM, making use of syscon/regmap. In the later patches support for
various TI SoCs is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series is a followup to:
<1415350967-2238-1-git-send-email-LW@KARO-electronics.de>
[PATCHv4 1/1] net: fec: fix regression on i.MX28 introduced by rx_copybreak support
to apply the cleanup patches that were originally sent along with the
bugfix patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lothar Waßmann [Mon, 17 Nov 2014 09:51:22 +0000 (10:51 +0100)]
net: fec: use swab32s() instead of cpu_to_be32()
when swap_buffer() is being called, we know for sure, that we need to
byte swap the data. Furthermore, this function is called for swapping
data in both directions. Thus cpu_to_be32() is semantically not
correct for all use cases. Use swab32s() to reflect this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Nov 2014 18:44:06 +0000 (13:44 -0500)]
Merge branch 'ebpf_maps'
Alexei Starovoitov says:
====================
implementation of eBPF maps
v1->v2:
renamed flags for MAP_UPDATE_ELEM command to be more concise,
clarified commit logs and improved comments in patches 1,3,7
per discussions with Daniel
Old v1 cover:
this set of patches adds implementation of HASH and ARRAY types of eBPF maps
which were described in manpage in commit b4fc1a460f30("Merge branch 'bpf-next'")
The difference vs previous version of these patches from August:
- added 'flags' attribute to BPF_MAP_UPDATE_ELEM
- in HASH type implementation removed per-map kmem_cache.
I was doing kmem_cache_create() for every map to enable selective slub
debugging to check for overflows and leaks. Now it's not needed, so just
use normal kmalloc() for map elements.
- added ARRAY type which was mentioned in manpage, but wasn't public yet
- added map testsuite and removed temporary bits from test_stubs
Note, eBPF programs cannot be attached to events yet.
It will come in the next set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
. check error conditions and sanity of hash and array map APIs
. check large maps (that kernel gracefully switches to vmalloc from kmalloc)
. check multi-process parallel access and stress test
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
fix errno of BPF_MAP_LOOKUP_ELEM command as bpf manpage
described it in commit b4fc1a460f30("Merge branch 'bpf-next'"):
-----
BPF_MAP_LOOKUP_ELEM
int bpf_lookup_elem(int fd, void *key, void *value)
{
union bpf_attr attr = {
.map_fd = fd,
.key = ptr_to_u64(key),
.value = ptr_to_u64(value),
};
return bpf(BPF_MAP_LOOKUP_ELEM, &attr, sizeof(attr));
}
bpf() syscall looks up an element with given key in a map fd.
If element is found it returns zero and stores element's value
into value. If element is not found it returns -1 and sets
errno to ENOENT.
and further down in manpage:
ENOENT For BPF_MAP_LOOKUP_ELEM or BPF_MAP_DELETE_ELEM, indicates that
element with given key was not found.
-----
In general all BPF commands return ENOENT when map element is not found
(including BPF_MAP_GET_NEXT_KEY and BPF_MAP_UPDATE_ELEM with
flags == BPF_MAP_UPDATE_ONLY)
Subsequent patch adds a testsuite to check return values for all of
these combinations.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
add new map type BPF_MAP_TYPE_ARRAY and its implementation
- optimized for fastest possible lookup()
. in the future verifier/JIT may recognize lookup() with constant key
and optimize it into constant pointer. Can optimize non-constant
key into direct pointer arithmetic as well, since pointers and
value_size are constant for the life of the eBPF program.
In other words array_map_lookup_elem() may be 'inlined' by verifier/JIT
while preserving concurrent access to this map from user space
- two main use cases for array type:
. 'global' eBPF variables: array of 1 element with key=0 and value is a
collection of 'global' variables which programs can use to keep the state
between events
. aggregation of tracing events into fixed set of buckets
- all array elements pre-allocated and zero initialized at init time
- key as an index in array and can only be 4 byte
- map_delete_elem() returns EINVAL, since elements cannot be deleted
- map_update_elem() replaces elements in an non-atomic way
(for atomic updates hashtable type should be used instead)
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
add new map type BPF_MAP_TYPE_HASH and its implementation
- maps are created/destroyed by userspace. Both userspace and eBPF programs
can lookup/update/delete elements from the map
- eBPF programs can be called in_irq(), so use spin_lock_irqsave() mechanism
for concurrent updates
- key/value are opaque range of bytes (aligned to 8 bytes)
- user space provides 3 configuration attributes via BPF syscall:
key_size, value_size, max_entries
- map takes care of allocating/freeing key/value pairs
- map_update_elem() must fail to insert new element when max_entries
limit is reached to make sure that eBPF programs cannot exhaust memory
- map_update_elem() replaces elements in an atomic way
- optimized for speed of lookup() which can be called multiple times from
eBPF program which itself is triggered by high volume of events
. in the future JIT compiler may recognize lookup() call and optimize it
further, since key_size is constant for life of eBPF program
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bpf: add 'flags' attribute to BPF_MAP_UPDATE_ELEM command
the current meaning of BPF_MAP_UPDATE_ELEM syscall command is:
either update existing map element or create a new one.
Initially the plan was to add a new command to handle the case of
'create new element if it didn't exist', but 'flags' style looks
cleaner and overall diff is much smaller (more code reused), so add 'flags'
attribute to BPF_MAP_UPDATE_ELEM command with the following meaning:
#define BPF_ANY 0 /* create new element or update existing */
#define BPF_NOEXIST 1 /* create new element if it didn't exist */
#define BPF_EXIST 2 /* update existing element */
bpf_update_elem(fd, key, value, BPF_NOEXIST) call can fail with EEXIST
if element already exists.
bpf_update_elem(fd, key, value, BPF_EXIST) can fail with ENOENT
if element doesn't exist.
Userspace will call it as:
int bpf_update_elem(int fd, void *key, void *value, __u64 flags)
{
union bpf_attr attr = {
.map_fd = fd,
.key = ptr_to_u64(key),
.value = ptr_to_u64(value),
.flags = flags;
};
David S. Miller [Tue, 18 Nov 2014 18:37:29 +0000 (13:37 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-11-18
This series contains updates to i40e only.
Shannon provides a patch to clean up the driver to only warn once that
PTP is not supported when linked at 100Mbps.
Mitch provides a fix for i40e where the VF interrupt processing takes
a long time and it is possible that we could lose a VFLR event if it
happens while processing a VFLR on another VF. To correct this situation,
we enable the VFLR interrupt cause before we begin processing any pending
resets.
Neerav provides several patches to update DCB support in i40e. When
there are DCB configuration changes based on DCBx, the firmware suspends
the port's Tx and generates an event to the PF. The PF is then
responsible to reconfigure the PF VSIs and switching topology as per the
updated DCB configuration and then resume the port's Tx by calling the
"Resume Port Tx" AQ command, so add this call to the flow that handles
DCB re-configuration in the PF. Allow the driver to query and use DCB
configuration from firmware when firmware DCBx agent is in CEE mode.
Add a check whether LLDP Agent's default AdminStatus is enabled or
disabled on a given port, and sets DCBx status to disabled if the
status is disabled. Fix an issue when the port TC configuration
changes as a result of DCBx and the driver modifies the enabled TCs for
the VEBs it manages but does not update the enabled_tc value that
was cached on a per VEB basis. Add a new PF state so that if a port's
Tx is in suspended state the Tx queue disable flow would just put the
request for the queue to be disabled and return without waiting for the
queue to be actually disabled. Allows the driver to enable/disable
the XPS based on the number of TCs being enabled for the given VSI.
v2: Dropped patch "i40e: Handle a single mss packet with more than 8 frags"
while we rework the patch after we test a bit more based on feedback from
Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Kirjanov [Mon, 17 Nov 2014 20:07:41 +0000 (23:07 +0300)]
PPC: bpf_jit_comp: Unify BPF_MOD | BPF_X and BPF_DIV | BPF_X
Reduce duplicated code by unifying
BPF_ALU | BPF_MOD | BPF_X and BPF_ALU | BPF_DIV | BPF_X
CC: Alexei Starovoitov<alexei.starovoitov@gmail.com> CC: Daniel Borkmann<dborkman@redhat.com> CC: Philippe Bergheaud<felix@linux.vnet.ibm.com> Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neerav Parikh [Wed, 12 Nov 2014 00:19:02 +0000 (00:19 +0000)]
i40e: Set XPS bit mask to zero in DCB mode
Due to DCBX configuration change if the VSI needs to use more than 1 TC;
it needs to disable the XPS maps that were set when operating in 1 TC mode.
Without disabling XPS the netdev layer will select queues based on those
settings and not use the TC queue mapping to make the queue selection.
This patch allows the driver to enable/disable the XPS based on the number
of TCs being enabled for the given VSI.
Change-ID: Idc4dec47a672d2a509f6d7fe11ed1ee65b4f0e08 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Wed, 12 Nov 2014 00:18:57 +0000 (00:18 +0000)]
i40e: Prevent link flow control settings when PFC is enabled
When PFC is enabled we should not proceed with setting the link flow control
parameters. Also, always report the link flow Tx/Rx settings as off when
PFC is enabled.
Change-ID: Ib09ec58afdf0b2e587ac9d8851a5c80ad58206c4 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Wed, 12 Nov 2014 00:18:51 +0000 (00:18 +0000)]
i40e: Do not disable/enable FCoE VSI with DCB reconfig
FCoE VSI Tx queue disable times out when reconfiguring as a result of
DCB TC configuration change event.
The hardware allows us to skip disabling and enabling of Tx queues for
VSIs with single TC enabled. As FCoE VSI is configured to have only
single TC we skip it from disable/enable flow.
Change-ID: Ia73ff3df8785ba2aa3db91e6f2c9005e61ebaec2 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Wed, 12 Nov 2014 00:18:46 +0000 (00:18 +0000)]
i40e: Modify Tx disable wait flow in case of DCB reconfiguration
When DCB TC configuration changes the firmware suspends the port's Tx.
Now, as DCB TCs may have changed the PF driver tries to reconfigure the
TC configuration of the VSIs it manages. As part of this process it disables
the VSI queues but the Tx queue disable will not complete as the port's
Tx has been suspended. So, waiting for Tx queues to go to disable state
in this flow may lead to detection of Tx queue disable timeout errors.
Hence, this patch adds a new PF state so that if a port's Tx is in
suspended state the Tx queue disable flow would just put the request for
the queue to be disabled and return without waiting for the queue to be
actually disabled.
Once the VSI(s) TC reconfiguration has been done and driver has called
firmware AQC "Resume PF Traffic" the driver checks the Tx queues requested
to be disabled are actually disabled before re-enabling them again.
Change-ID: If3e03ce4813a4e342dbd5a1eb1d2861e952b7544 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Wed, 12 Nov 2014 00:18:41 +0000 (00:18 +0000)]
i40e: Update VEB's enabled_tc after reconfiguration
When the port TC configuration changes as a result of DCBx the driver
modifies the enabled TCs for the VEBs it manages. But, in the process
it did not update the enabled_tc value that it caches on a per VEB basis.
So, when the next reconfiguration event occurs where the number of TC
value is same as the value cached in enabled_tc for a given VEB; driver
does not modify it's TC configuration by calling appropriate AQ command
believing it is running with the same configuration as requested.
Now, as the VEB is not actually enabled for the TCs that are there any
TC configuration command for VSI attached to that VEB with TCs that are
not enabled for the VEB fails.
This patch fixes this issue.
Change-ID: Ife5694469b05494228e0d850429ea1734738cf29 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Wed, 12 Nov 2014 00:18:30 +0000 (00:18 +0000)]
i40e: Check for LLDP AdminStatus before querying DCBX
This patch adds a check whether LLDP Agent's default AdminStatus is
enabled or disabled on a given port. If it is disabled then it sets
the DCBX status to disabled as well; and would not query firmware for
any DCBX configuration data.
Change-ID: I73c0b9f0adbf4cae177d14914b20a48c9a8f50fd Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Wed, 12 Nov 2014 00:18:25 +0000 (00:18 +0000)]
i40e: Add support to firmware CEE DCBX mode
This patch allows i40e driver to query and use DCB configuration from
firmware when firmware DCBX agent is in CEE mode.
Change-ID: I30f92a67eb890f0f024f35339696e6e83d49a274 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Wed, 12 Nov 2014 00:18:20 +0000 (00:18 +0000)]
i40e: Resume Port Tx after DCB event
When there are DCB configuration changes based on DCBX the firmware suspends
the port's Tx and generates an event to the PF. The PF is then responsible
to reconfigure the PF VSIs and switching topology as per the updated DCB
configuration and then resume the port's Tx by calling the "Resume Port Tx"
AQ command.
This patch adds this call to the flow that handles DCB re-configuration in
the PF.
Change-ID: I5b860ad48abfbf379b003143c4d3453e2ed5cc1c Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-By: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Tue, 11 Nov 2014 03:15:04 +0000 (03:15 +0000)]
i40e: re-enable VFLR interrupt sooner
VF interrupt processing takes a looooong time, and it's possible that we
could lose a VFLR event if it happens while we're processing a VFLR on
another VF. This would leave the VF in a semi-permanent reset state,
which would not be cleared until yet another VF experiences a VFLR.
To correct this situation, we enable the VFLR interrupt cause before we
begin processing any pending resets. This means that any VFLR that
occurs during reset processing will generate another interrupt and this
routine will get called again.
This change may cause a spurious interrupt when multiple VFLRs occur
very close together in time. If this happens, then this routine will be
called again and it will detect no outstanding VFLR events and do
nothing. No harm, no foul.
Change-ID: Id0451f3e6e73a2cf6db1668296c71e129b59dc19 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Tue, 11 Nov 2014 03:15:03 +0000 (03:15 +0000)]
i40e: only warn once of PTP nonsupport in 100Mbit speed
Only warn once that PTP is not supported when linked at 100Mbit.
Yes, using a static this way means that this once-only message is not
port specific, but once only for the life of the driver, regardless of
the number of ports. That should be plenty.
Change-ID: Ie6476530056df408452e195ef06afd4f57caa4b2 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Roger Quadros [Mon, 17 Nov 2014 12:09:03 +0000 (14:09 +0200)]
net: can: c_can: Add support for TI am4372 DCAN
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Fri, 14 Nov 2014 15:40:13 +0000 (17:40 +0200)]
can: c_can: Disable pins when CAN interface is down
DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.
To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Fri, 7 Nov 2014 14:49:19 +0000 (16:49 +0200)]
can: c_can: Add support for START pulse in RAMINIT sequence
Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Fri, 14 Nov 2014 15:37:39 +0000 (17:37 +0200)]
can: c_can: Add syscon/regmap RAMINIT mechanism
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Fri, 7 Nov 2014 14:49:16 +0000 (16:49 +0200)]
can: c_can: Introduce c_can_driver_data structure
We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.
Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Fri, 7 Nov 2014 14:49:15 +0000 (16:49 +0200)]
can: c_can: Add timeout to c_can_hw_raminit_ti()
TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David S. Miller [Sun, 16 Nov 2014 20:59:19 +0000 (15:59 -0500)]
Merge branch 'rss_key_fill'
Eric Dumazet says:
====================
net: provide common RSS key infrastructure
RSS (Receive Side Scaling) uses a 40 bytes key to provide hash for incoming
packets to select appropriate incoming queue on NIC.
Hash algo (Toeplitz) is also well known and documented by Microsoft
(search for "Verifying the RSS Hash Calculation")
Problem is that some drivers use a well known key.
It makes very easy for attackers to target one particular RX queue,
knowing that number of RX queues is a power of two, or at least some
small number.
Other drivers use a random value per port, making difficult
tuning on bonding setups.
Lets add a common infrastructure, so that host gets an unique
RSS key, and drivers do not have to worry about this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Nov 2014 14:23:15 +0000 (06:23 -0800)]
ixgbe: use netdev_rss_key_fill() helper
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Nov 2014 14:23:14 +0000 (06:23 -0800)]
igb: use netdev_rss_key_fill() helper
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Nov 2014 14:23:13 +0000 (06:23 -0800)]
i40e: use netdev_rss_key_fill() helper
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Nov 2014 14:23:12 +0000 (06:23 -0800)]
fm10k: use netdev_rss_key_fill() helper
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Nov 2014 14:23:11 +0000 (06:23 -0800)]
e100e: use netdev_rss_key_fill() helper
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Nov 2014 14:23:10 +0000 (06:23 -0800)]
be2net:use netdev_rss_key_fill() helper
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Rename rss_hkey local variable to rss_key to have consistent name among
drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Sathya Perla <sathya.perla@emulex.com> Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com> Cc: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Nov 2014 14:23:08 +0000 (06:23 -0800)]
tg3: use netdev_rss_key_fill() helper
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Prashant Sreedharan <prashant@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Nov 2014 14:23:05 +0000 (06:23 -0800)]
net: provide a per host RSS key generic infrastructure
RSS (Receive Side Scaling) typically uses Toeplitz hash and a 40 or 52 bytes
RSS key.
Some drivers use a constant (and well known key), some drivers use a random
key per port, making bonding setups hard to tune. Well known keys increase
attack surface, considering that number of queues is usually a power of two.
This patch provides infrastructure to help drivers doing the right thing.
netdev_rss_key_fill() should be used by drivers to initialize their RSS key,
even if they provide ethtool -X support to let user redefine the key later.
A new /proc/sys/net/core/netdev_rss_key file can be used to get the host
RSS key even for drivers not providing ethtool -x support, in case some
applications want to precisely setup flows to match some RX queues.
David S. Miller [Sun, 16 Nov 2014 20:48:01 +0000 (15:48 -0500)]
Merge branch 'mv88e6171_temps'
Andrew Lunn says:
====================
Add temperature reading and registers dump to mv88e6171
These patches centralize the temperature sensor reading code, and then
make use of it with the mv88e6171 which has a compatible
sensor. Additionally, support is added for reading the mv88e6171 via
ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 15 Nov 2014 21:24:52 +0000 (22:24 +0100)]
net: dsa: mv88e6171: Add support for reading the temperature
This chip also has a temperature sensor which can be read using the
common code. In order to use it, add the needed mutex protection for
accessing registers via the shared code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 15 Nov 2014 21:24:51 +0000 (22:24 +0100)]
net: dsa: Centralise code for reading the temperature sensor
The method to read the temperature used in the mve6123_61_65 driver
can also be used for other chips. Move the code into the shared code
base of mv88e6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log