Peter Chen [Thu, 30 Oct 2014 03:10:04 +0000 (11:10 +0800)]
usb: chipidea: imx: add stream mode enable for device mode at imx6sl/imx6sx
Stream mode enable is known for better performance, this stream mode
enable patch has been passed with stress tests at device mode for
imx6sl and imx6sx, and no issue is found.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Peter Chen [Thu, 30 Oct 2014 01:15:15 +0000 (09:15 +0800)]
usb: chipidea: define stream mode disable for both roles
The system bus and chipidea IP have different limitations for
both host and device mode.
For example, with below errata, we need to enable SDIS(Stream Disable
Mode) at host mode. But we don't want it for device mode at the
same system.
TAR 9000378958
Title: Non-Double Word Aligned Buffer Address Sometimes Causes Host to
Hang on OUT Retry
Impacted Configuration: Host mode, all transfer types
Description:
The host core operating in streaming mode may under run while sending
the data packet of an OUT transaction. This under run can occur if
there are unexpected system delays in fetching the remaining packet
data from memory. The host forces a bad CRC on the packet, the device
detects the error and discards the packet. The host then retries a Bulk,
Interrupt, or Control transfer if an under run occurs according to the
USB specification. During simulations, it was found that the host does
not issue the retry of the failed bulk OUT. It does not issue any other
transactions except SOF packets that have incorrect frame numbers.
The second failure mode occurs if the under run occurs on an ISO OUT
transaction and the next ISO transaction is a zero byte packet. The host
does not issue any transactions (including SOFs). The device detects a
Suspend condition, reverts to full speed, and waits for resume signaling.
A third failure mode occurs when the host under runs on an ISO OUT and
the next ISO in the schedule is an ISO OUT with two max packets of 1024
bytes each. The host should issue MDATA for the first OUT followed by
DATA1 for the second. However, it drops the MDATA transaction, and
issues the DATA1 transaction.
The system impact of this bug is the same regardless of the failure mode
observed. The host core hangs, the ehci_ctrl state machine waits for the
protocol engine to send the completion status for the corrupted
transaction, which never occurs. No indication is sent to the host
controller driver, no register bits change and no interrupts occur.
Eventually the requesting application times out.
Detailed internal behavior:
The EHCI control state machine (ehci_ctrl) in the DMA block is responsible
for parsing the schedules and initiating all transactions. The ehci_ctrl
state machine passes the transaction details to the protocol block by
writing the transaction information in to the TxFIFO. It then asserts
the pe_hst_run_pkt signal to inform the host protocol state machine
(pe_hst_state) that there is a packet in the TxFIFO.
A tag of 0x0 indicates a start of packet with the data providing the
following information:
35:32 Tag
31:30 Reserved
29:23 Endpoint (lowest 4 bits)
22:16 Address
15:10 Reserved
9:8 Endpoint speed
7:6 Endpoint type
5:6 Data Toggle
3:0 PID
The pe_hst_state reads the packet information and constructs the packet
and issues it to the PHY interface.
The ehci_ctrl state machine writes the start transaction information in
to the TxFIFO as 0x03002910c for the OUT packet that had the under run
error. However, it writes 0xC3002910C for the retry of the Out
transaction, which is incorrect.
The pe_hst_state enters a bus timeout state after sending the bad CRC
for the packet that under ran. It then purges any data that was back
filled in to the TxFIFO for the packet that under ran. The pe_hst_state
machine stops purging the TxFIFO when it is empty or if it reads a
location that has a tag of 0x0, indicating a start of packet command.
The pe_hst_state reads 0xC3002910C and discards it as it does not decode
to a start of packet command. It continues to purge the OUT data that
has been pre-buffered for the OUT retry . The pe_hst_state detects the
hst_packet_run signal and attempts to read the PID and address
information from the TxFIFO. This location has packet data and so does
not decode to a valid PID and so falls through to the PE_HST_SOF_LOAD
state where the frame_num_counter is updated. The frame_num_counter
is updated with the data in the TxFIFO. In this case, the data is
incorrect as the ehci_ctrl state machine did not initiate the load.
The hst_pe_state machine detects the SOF request signal and sends an
SOF with the bad frame number. Meanwhile, the ehci_ctrl state machine
waits indefinitely in the run_pkt state waiting for the completion
status from pe_hst_state machine, which will never happen.
The ISO failure case is similar except that there is no retry for ISO.
The ehci_ctrl state machine moves to the next transfer in the periodic
schedule. If the under run occurs on the last entry of the periodic
list then it moves to the Async schedule.
In the case of ISO OUT simulations, the next ISO is a zero byte OUT
and again the start of packet command gets corrupted. The TxFIFO is
empty when the hst_pe_state attempts to read the Address and PID
information as the transaction is a zero byte packet. This results
in the hst_pe_state machine staying in the GET_PID state, which means
that it does not issue any transactions (including SOFs). The device
detects a Suspend condition and reverts to full speed mode and waits
for a Resume or Reset signal.
The EHCI specification allows a Non-DoubleWord (32 bits) offset to
be used as a current offset for Buffer Pointer Page 0 of the qTD.
In Non-DoubleWord aligned cases, the core reads the packet data
from the AHB memory, performs the alignment operation before writing
it in to the TxFIFO as a 32 bit data word. An End Of Packet tag (EOP)
is written to the TxFIFO after all the packet data has been written
in to the TxFIFO. The alignment function is reset to Idle by the EOP
tag. The corruption of the start of packet command arises because the
packet buffer for the OUT transaction that under ran is not aligned
to a DoubleWord, and hence no EOP tag is written to the TxFIFO. The
alignment function is still active when the start packet information
is written in to the TxFIFO for the retry of the bulk packet or for
the next transaction in the case of an under run on an ISO. This
results in the corruption of the start tag and the transaction
information.
Click for waveform showing the command 0x 0000300291 being written in
to the TX FIFO for the Out that under ran.
Click for waveform showing the command 0xC3002910C written to the
TxFIFO instead of 0x 0000300291
Versions affected: Versions 2.10a and previous versions
How discovered: Customer simulation
Workaround:
1- The EHCI specification allows a non-DoubleWord offset to be used
as a current offset for Buffer Pointer Page 0 of the qTD. However,
if a DoubleWord offset is used then this issue does not arise.
2- Use non streaming mode to eliminate under runs.
Resolution:
The fix involves changes to the traffic state machine in the
vusb_hs_dma_traf block. The ehci_ctrl state machine updates the context
information by encoding the transaction results on the
hst_op_context_update signals at the end of a transaction. The signal
hst_op_context_update is added to the traffic state machine, and the
tx_fifo_under_ran_r signal is generated if the transaction results in
an under run error. Click for waveform
The traffic state machine then traverses to the do_eop states if the
tx_fifo_under_ran error is asserted. Thus an EOP tag is written in to
the TxFIFO as shown in this waveform .
The EOP tag resets the align state machine to the Idle state ensuring
that the next command written by the echi_ctrl state machine does not
get corrupted.
File(s) modified:
RTL code fixed: …..
Method of reproducing: This failure cannot be reproduced in the current
test bench.
Date Found: March 2010
Date Fixed: June 2010
Update information:
Added the RTL code fix
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Peter Chen [Wed, 5 Aug 2015 02:16:19 +0000 (10:16 +0800)]
usb: chipidea: host: override hcd reset API
The system configuration API should be called before the controller
run, otherwise, undefined results may occur. So, we override hcd
reset API, and add system configuration API after controller reset.
Cc: Li Jun <peter.chen@freescale.com> Cc: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tomeu Vizoso [Thu, 6 Aug 2015 13:09:54 +0000 (15:09 +0200)]
usb: chipidea: imx: properly check for usbmisc
If usbmisc hasn't probed yet, defer the probe.
It's not enough to check if the platform device for the OF node of the
usbmisc has been registered, but it also needs to have been probed
already before we can call imx_usbmisc_init().
This can happen if the order in which devices are probed change due to
async probing or on-demand probing of dependencies.
Nicholas Krause [Sat, 27 Jun 2015 04:34:48 +0000 (00:34 -0400)]
usb:chipidea:Make the function hw_alloc_repmap have a return type of void
This makes the function hw_alloc_repmap be declared to have a return
type of void now due to this particular function never returning
a error code to its caller due to this function always running
successfully to completion nor it's caller putting the return
value into a variable in order to check if a error code is passed
from the function hw_alloc_repmap when calling this function.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Peter Chen [Mon, 22 Sep 2014 08:45:39 +0000 (16:45 +0800)]
usb: chipidea: introduce ITC tuning interface
ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Peter Chen [Tue, 17 Mar 2015 02:40:50 +0000 (10:40 +0800)]
usb: chipidea: introduce ci_platform_configure
It is used to configure controller parameters according to
platform data, like speed, stream mode, etc, both host and
device's initialization need it, most of code are the
same for both roles, with this new interface, it can reduce
the duplicated code and be easy to maintain in future.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
For i.mx platform, set ttctrl.ttha with non-zero value only affects
sitd, and ehci core makes sure the schedule is not full when accepts
new request, so it will not occur the transaction which will acorss
the SoF.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Peter Chen [Thu, 18 Jun 2015 03:51:53 +0000 (11:51 +0800)]
usb: chipidea: add ttctrl.ttha control interface
The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu CC: michael.tessier@axiontech.ca Signed-off-by: Peter Chen <peter.chen@freescale.com>
Linus Torvalds [Sun, 9 Aug 2015 07:38:42 +0000 (09:38 +0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Just small ALPS and Elan touchpads, and other driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add special check for fw_version 0x470f01 touchpad
Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning
Input: alps - only Dell laptops have separate button bits for v2 dualpoint sticks
Input: axp20x-pek - add module alias
Input: turbografx - fix potential out of bound access
Linus Torvalds [Sun, 9 Aug 2015 02:59:21 +0000 (05:59 +0300)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2. No area does particularly stand
out but we have a two unpleasant ones:
- Kernel ptes are marked with a global bit which allows the kernel to
share kernel TLB entries between all processes. For this to work
both entries of an adjacent even/odd pte pair need to have the
global bit set. There has been a subtle race in setting the other
entry's global bit since ~ 2000 but it take particularly
pathological workloads that essentially do mostly vmalloc/vfree to
trigger this.
This pull request fixes the 64-bit case but leaves the case of 32
bit CPUs with 64 bit ptes unsolved for now. The unfixed cases
affect hardware that is not available in the field yet.
- Instruction emulation requires loading instructions from user space
but the current fast but simplistic approach will fail on pages
that are PROT_EXEC but !PROT_READ. For this reason we temporarily
do not permit this permission and will map pages with PROT_EXEC |
PROT_READ.
The remainder of this pull request is more or less across the field
and the short log explains them well"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Make set_pte() SMP safe.
MIPS: Replace add and sub instructions in relocate_kernel.S with addiu
MIPS: Flush RPS on kernel entry with EVA
Revert "MIPS: BCM63xx: Provide a plat_post_dma_flush hook"
MIPS: BMIPS: Delete unused Kconfig symbol
MIPS: Export get_c0_perfcount_int()
MIPS: show_stack: Fix stack trace with EVA
MIPS: do_mcheck: Fix kernel code dump with EVA
MIPS: SMP: Don't increment irq_count multiple times for call function IPIs
MIPS: Partially disable RIXI support.
MIPS: Handle page faults of executable but unreadable pages correctly.
MIPS: Malta: Don't reinitialise RTC
MIPS: unaligned: Fix build error on big endian R6 kernels
MIPS: Fix sched_getaffinity with MT FPAFF enabled
MIPS: Fix build with CONFIG_OF=y for non OF-enabled targets
CPUFREQ: Loongson2: Fix broken build due to incorrect include.
Linus Torvalds [Sun, 9 Aug 2015 02:56:31 +0000 (05:56 +0300)]
Merge branch 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"We have a btrfs quota regression fix.
I merged this one on Thursday and have run it through tests against
current master.
Normally I wouldn't have sent this while you were finalizing rc6, but
I'm feeding mosquitoes in the adirondacks next week, so I wanted to
get this one out before leaving. I'll leave longer tests running and
check on things during the week, but I don't expect any problems"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: qgroup: Fix a regression in qgroup reserved space.
Linus Torvalds [Sun, 9 Aug 2015 02:54:27 +0000 (05:54 +0300)]
Merge branch 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"Specifics:
- fix an error that "weight_attr" sysfs attribute is not removed
while unbinding. From: Viresh Kumar.
- fix power allocator governor tracing to return the real request.
From Javi Merino.
- remove redundant owner assignment of hisi platform thermal driver.
From Krzysztof Kozlowski.
- a couple of small fixes of Exynos thermal driver. From Krzysztof
Kozlowski and Chanwoo Choi"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Drop owner assignment from platform_driver
thermal: exynos: Remove unused code related to platform_data on probe()
thermal: exynos: Add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF
thermal: exynos: Disable the regulator on probe failure
thermal: power_allocator: trace the real requested power
thermal: remove dangling 'weight_attr' device file
Tal Shorer [Fri, 7 Aug 2015 19:35:51 +0000 (22:35 +0300)]
usb: hcd.h: Fix the values of SetHubDepth and GetPortErrorCount to match USB 3.1 specification
>From the usb 3.1 spec available at http://www.usb.org/developers/docs/
table 10-7 (Hub Class Requests) specifies the values for SetHubDepth and
GetPortErrorCount as:
Request bmRequestType bRequest wValue wIndex wLength Data
SetHubDepth 00100000B SET_HUB_DEPTH Hub Depth Zero Zero None
GetPortErrorCount 10100011B GET_PORT_ERR_COUNT Zero Port Two Number of Link Errors on this port
Fix these two values to match the spec.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lu Baolu [Thu, 6 Aug 2015 16:24:01 +0000 (19:24 +0300)]
xhci: xHCI 1.1: Stopped - Short Packet Capability (SPC)
This patch enables xhci driver to support SPC by handling
Stopped - Short Packet event in transfer event path.
If SPC = '1' and the stop endpoint command is executed, after a Short
Packet condition has been detected, but before the end of the TD has been
reached, (i.e. the TD is in progress for pipe), then a Transfer Event TRB
with its Completion Code set to Stopped - Short Packet and its TRB
Transfer Length set to value of the EDTLA shall be forced for the
interrupted TRB, irrespective of whether its IOC or ISP flags are set.
This Transfer Event TRB will precede the Command Completion Event TRB for
the command, and is referred to as a Stopped Transfer Event.
Lu Baolu [Thu, 6 Aug 2015 16:24:00 +0000 (19:24 +0300)]
xhci: xHCI 1.1: Contiguous Frame ID Capability (CFC)
If the Contiguous Frame ID Capability is supported (CFC = 1),
then the xHC shall match the Frame ID in every Isoch TD with
SIA = 0 against the Frame Index of the MFINDEX register. This
rule ensures resynchronization of Isoch TDs even if some are
dropped due to Missed Service Errors or Stopping the endpoint.
This patch enables xHCI driver to support CFC by calculating
and setting the Frame ID field of an Isoch TRB.
[made some dbg messages checkpatch friendly -Mathias] Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reyad Attiyat [Thu, 6 Aug 2015 16:23:58 +0000 (19:23 +0300)]
usb: xhci: Add support for URB_ZERO_PACKET to bulk/sg transfers
This commit checks for the URB_ZERO_PACKET flag and creates an extra
zero-length td if the urb transfer length is a multiple of the endpoint's
max packet length.
Rafał Miłecki [Thu, 6 Aug 2015 16:23:57 +0000 (19:23 +0300)]
usb: xhci: make USB_XHCI_PLATFORM selectable
Right now xhci-plat-hcd can be built when using one of platform specific
drivers only (mvebu/rcar). There shouldn't be such limitation as some
platforms may not require any quirks and may want to just use a generic
driver ("generic-xhci" / "xhci-hcd").
Linus Torvalds [Sat, 8 Aug 2015 01:38:00 +0000 (04:38 +0300)]
Merge tag 'arc-v4.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Here's a late pull request for accumulated ARC fixes which came out of
extended testing of the new ARCv2 port with LTP etc. llock/scond
livelock workaround has been reviewed by PeterZ. The changes look a
lot but I've crafted them into finer grained patches for better
tracking later.
I have some more fixes (ARC Futex backend) ready to go but those will
have to wait for tglx to return from vacation.
Summary:
- Enable a reduced config of HS38 (w/o div-rem, ll64...)
- Add software workaround for LLOCK/SCOND livelock
- Fallout of a recent pt_regs update"
* tag 'arc-v4.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: spinlock/rwlock/atomics: reduce 1 instruction in exponential backoff
ARC: Make pt_regs regs unsigned
ARCv2: spinlock/rwlock: Reset retry delay when starting a new spin-wait cycle
ARCv2: spinlock/rwlock/atomics: Delayed retry of failed SCOND with exponential backoff
ARC: LLOCK/SCOND based rwlock
ARC: LLOCK/SCOND based spin_lock
ARC: refactor atomic inline asm operands with symbolic names
Revert "ARCv2: STAR 9000837815 workaround hardware exclusive transactions livelock"
ARCv2: [axs103_smp] Reduce clk for Quad FPGA configs
ARCv2: Fix the peripheral address space detection
ARCv2: allow selection of page size for MMUv4
ARCv2: lib: memset: Don't assume 64-bit load/stores
ARCv2: lib: memcpy: Missing PREFETCHW
ARCv2: add knob for DIV_REV in Kconfig
ARC/time: Migrate to new 'set-state' interface
Linus Torvalds [Sat, 8 Aug 2015 01:36:40 +0000 (04:36 +0300)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fix from Michael Tsirkin:
"A last minute fix for the new virtio input driver. It seems pretty
obvious, and the problem it's fixing would be quite hard to debug"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-input: reset device and detach unused during remove
Linus Torvalds [Sat, 8 Aug 2015 01:35:14 +0000 (04:35 +0300)]
Merge tag 'dm-4.2-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- stable fix for a dm_merge_bvec() regression on 32 bit Fedora systems.
- fix for a 4.2 DM thinp discard regression due to inability to
properly delete a range of blocks in a data mapping btree.
* tag 'dm-4.2-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree remove: fix bug in remove_one()
dm: fix dm_merge_bvec regression on 32 bit systems
Linus Torvalds [Sat, 8 Aug 2015 01:33:35 +0000 (04:33 +0300)]
Merge tag 'sound-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The only bulk changes in this request is ABI updates for ASoC topology
API. It's a new API that was introduced in 4.2, and we'd like to
avoid ABI change after the release, so it's taken now. As there is no
real in-tree user for this API, it should be fairly safe.
Other than that, the usual small fixes are found in various drivers:
ASoC cs4265, rt5645, intel-sst, firewire, oxygen and HD-audio"
* tag 'sound-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: topology: Add private data type and bump ABI version to 3
ASoC: topology: Add ops support to byte controls UAPI
ASoC: topology: Update TLV support so we can support more TLV types
ASoC: topology: add private data to manifest
ASoC: topology: Add subsequence in topology
ALSA: hda - one Dell machine needs the headphone white noise fixup
ALSA: fireworks/firewire-lib: add support for recent firmware quirk
Revert "ALSA: fireworks: add support for AudioFire2 quirk"
ASoC: topology: fix typo in soc_tplg_kcontrol_bind_io()
ALSA: HDA: Dont check return for snd_hdac_chip_readl
ALSA: HDA: Fix stream assignment for host in decoupled mode
ASoC: rt5645: Fix lost pin setting for DMIC1
ALSA: oxygen: Fix logical-not-parentheses warning
ASoC: Intel: sst_byt: fix initialize 'NULL device *' issue
ASoC: Intel: haswell: fix initialize 'NULL device *' issue
ASoC: cs4265: Fix setting dai format for Left/Right Justified
Linus Torvalds [Sat, 8 Aug 2015 01:30:37 +0000 (04:30 +0300)]
Merge tag 'hwmon-for-linus-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Export module alias information in g762 and nct7904 to support
auto-loading.
- Blacklist Dell Studio XPS 8100 in dell-smm to fix fan control
problems.
* tag 'hwmon-for-linus-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (g762) Export OF module alias information
hwmon: (nct7904) Export I2C module alias information
hwmon: (dell-smm) Blacklist Dell Studio XPS 8100
Linus Torvalds [Sat, 8 Aug 2015 01:27:51 +0000 (04:27 +0300)]
Merge tag 'usb-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 4.2-rc6 that resolve some reported
issues.
All of these have been in the linux-next tree for a while, full
details on the patches are in the shortlog below"
* tag 'usb-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
ARM: dts: dra7: Add syscon-pllreset syscon to SATA PHY
drivers/usb: Delete XHCI command timer if necessary
xhci: fix off by one error in TRB DMA address boundary check
usb: udc: core: add device_del() call to error pathway
phy: ti-pipe3: i783 workaround for SATA lockup after dpll unlock/relock
phy-sun4i-usb: Add missing EXPORT_SYMBOL_GPL for sun4i_usb_phy_set_squelch_detect
USB: sierra: add 1199:68AB device ID
usb: gadget: f_printer: actually limit the number of instances
usb: gadget: f_hid: actually limit the number of instances
usb: gadget: f_uac2: fix calculation of uac2->p_interval
usb: gadget: bdc: fix a driver crash on disconnect
usb: chipidea: ehci_init_driver is intended to call one time
USB: qcserial: Add support for Dell Wireless 5809e 4G Modem
USB: qcserial/option: make AT URCs work for Sierra Wireless MC7305/MC7355
Linus Torvalds [Sat, 8 Aug 2015 01:26:31 +0000 (04:26 +0300)]
Merge tag 'staging-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are three bugfixes for some staging driver issues that have been
reported. All have been in the linux-next tree for a while"
* tag 'staging-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: lustre: Include unaligned.h instead of access_ok.h
staging: vt6655: vnt_bss_info_changed check conf->beacon_rate is not NULL
staging: comedi: das1800: add missing break in switch
Linus Torvalds [Sat, 8 Aug 2015 01:25:10 +0000 (04:25 +0300)]
Merge tag 'char-misc-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some extcon fixes for 4.2-rc6 that resolve some reported
problems.
All have been in linux-next for a while"
* tag 'char-misc-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
extcon: Fix extcon_cable_get_state() from getting old state after notification
extcon: Fix hang and extcon_get/set_cable_state().
extcon: palmas: Fix NULL pointer error
Linus Torvalds [Sat, 8 Aug 2015 01:18:14 +0000 (04:18 +0300)]
Merge tag 'drm-intel-fixes-2015-08-07' of git://anongit.freedesktop.org/drm-intel
Pull drm fixes from Daniel Vetter:
"One i915 regression fix and a drm core one since Dave's not around,
both introduced in 4.2 so not cc: stable.
The fix for the warning Ted reported isn't in here yet since he didn't
yet supply a tested-by and I can't repro this one myself (it's in
fixup code that needs firmware doing something i915 wouldn't do)"
* tag 'drm-intel-fixes-2015-08-07' of git://anongit.freedesktop.org/drm-intel:
drm/vblank: Use u32 consistently for vblank counters
drm/i915: Allow parsing of variable size child device entries from VBT
Joe Thornber [Fri, 7 Aug 2015 15:33:01 +0000 (16:33 +0100)]
dm btree remove: fix bug in remove_one()
remove_one() was not incrementing the key for the beginning of the
range, so not all entries were being removed. This resulted in
discards that were not unmapping all blocks.
Fixes: 4ec331c3ea ("dm btree: add dm_btree_remove_leaves()") Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
drm/vblank: Fixup and document timestamp update/read barriers
I've switched vblank->count from atomic_t to unsigned long and
accidentally created an integer comparison bug in
drm_vblank_count_and_time since vblanke->count might overflow the u32
local copy and hence the retry loop never succeed.
Fix this by consistently using u32.
Cc: Michel Dänzer <michel@daenzer.net> Reported-by: Michel Dänzer <michel@daenzer.net> Reviewed-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Takashi Iwai [Fri, 7 Aug 2015 11:53:41 +0000 (13:53 +0200)]
Merge tag 'asoc-fix-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.2
There are a couple of small driver specific fixes here but the
overwhelming bulk of these changes are fixes to the topology ABI that
has been newly introduced in v4.2. Once this makes it into a release we
will have to firm this up but for now getting enhancements in before
they've made it into a release is the most expedient thing.
Linus Torvalds [Fri, 7 Aug 2015 02:20:40 +0000 (05:20 +0300)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
writeback: fix initial dirty limit
mm/memory-failure: set PageHWPoison before migrate_pages()
mm: check __PG_HWPOISON separately from PAGE_FLAGS_CHECK_AT_*
mm/memory-failure: give up error handling for non-tail-refcounted thp
mm/memory-failure: fix race in counting num_poisoned_pages
mm/memory-failure: unlock_page before put_page
ipc: use private shmem or hugetlbfs inodes for shm segments.
mm: initialize hotplugged pages as reserved
ocfs2: fix shift left overflow
kthread: export kthread functions
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
lib/iommu-common.c: do not use 0xffffffffffffffffl for computing align_mask
mm/slub: allow merging when SLAB_DEBUG_FREE is set
signalfd: fix information leak in signalfd_copyinfo
signal: fix information leak in copy_siginfo_to_user
signal: fix information leak in copy_siginfo_from_user32
ocfs2: fix BUG in ocfs2_downconvert_thread_do_work()
fs, file table: reinit files_stat.max_files after deferred memory initialisation
mm, meminit: replace rwsem with completion
mm, meminit: allow early_pfn_to_nid to be used during runtime
...
David S. Miller [Fri, 7 Aug 2015 02:13:25 +0000 (19:13 -0700)]
sparc64: Fix userspace FPU register corruptions.
If we have a series of events from userpsace, with %fprs=FPRS_FEF,
like follows:
ETRAP
ETRAP
VIS_ENTRY(fprs=0x4)
VIS_EXIT
RTRAP (kernel FPU restore with fpu_saved=0x4)
RTRAP
We will not restore the user registers that were clobbered by the FPU
using kernel code in the inner-most trap.
Traps allocate FPU save slots in the thread struct, and FPU using
sequences save the "dirty" FPU registers only.
This works at the initial trap level because all of the registers
get recorded into the top-level FPU save area, and we'll return
to userspace with the FPU disabled so that any FPU use by the user
will take an FPU disabled trap wherein we'll load the registers
back up properly.
But this is not how trap returns from kernel to kernel operate.
The simplest fix for this bug is to always save all FPU register state
for anything other than the top-most FPU save area.
Getting rid of the optimized inner-slot FPU saving code ends up
making VISEntryHalf degenerate into plain VISEntry.
Longer term we need to do something smarter to reinstate the partial
save optimizations. Perhaps the fundament error is having trap entry
and exit allocate FPU save slots and restore register state. Instead,
the VISEntry et al. calls should be doing that work.
This bug is about two decades old.
Reported-by: James Y Knight <jyknight@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 7 Aug 2015 01:51:14 +0000 (04:51 +0300)]
Merge branch 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux
Pull amdgpu fixes from Alex Deucher:
"Just a few amdgpu fixes to make sure we report the proper firmware
information and number of render buffers to userspace and a typo in a
debugging function"
[ Pulling directly from Alex since Dave Airlie is on vacation - Linus ]
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: set fw_version and feature_version for smu fw loading
drm/amdgpu: add feature version for SDMA ucode
drm/amdgpu: add feature version for RLC and MEC v2
drm/amdgpu: increment queue when iterating on this variable.
drm/amdgpu: fix rb setting for CZ
Linus Torvalds [Fri, 7 Aug 2015 01:48:46 +0000 (04:48 +0300)]
Merge branch 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull TDA998x i2c driver fixes from Russell King:
"This fixes the double-checksumming of the AVI infoframe which was
resulting in the checksum always being zero. It went unnoticed as
none of my HDMI devices had a problem with this"
[ Pulling directly from rmk since Dave Airlie is on vacation - Linus ]
* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: fix bad checksum of the HDMI AVI infoframe
Naoya Horiguchi [Thu, 6 Aug 2015 22:47:11 +0000 (15:47 -0700)]
mm/memory-failure: set PageHWPoison before migrate_pages()
Now page freeing code doesn't consider PageHWPoison as a bad page, so by
setting it before completing the page containment, we can prevent the
error page from being reused just after successful page migration.
I added TTU_IGNORE_HWPOISON for try_to_unmap() to make sure that the
page table entry is transformed into migration entry, not to hwpoison
entry.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Dean Nelson <dnelson@redhat.com> Cc: Tony Luck <tony.luck@intel.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Hugh Dickins <hughd@google.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Thu, 6 Aug 2015 22:47:08 +0000 (15:47 -0700)]
mm: check __PG_HWPOISON separately from PAGE_FLAGS_CHECK_AT_*
The race condition addressed in commit add05cecef80 ("mm: soft-offline:
don't free target page in successful page migration") was not closed
completely, because that can happen not only for soft-offline, but also
for hard-offline. Consider that a slab page is about to be freed into
buddy pool, and then an uncorrected memory error hits the page just
after entering __free_one_page(), then VM_BUG_ON_PAGE(page->flags &
PAGE_FLAGS_CHECK_AT_PREP) is triggered, despite the fact that it's not
necessary because the data on the affected page is not consumed.
To solve it, this patch drops __PG_HWPOISON from page flag checks at
allocation/free time. I think it's justified because __PG_HWPOISON
flags is defined to prevent the page from being reused, and setting it
outside the page's alloc-free cycle is a designed behavior (not a bug.)
For recent months, I was annoyed about BUG_ON when soft-offlined page
remains on lru cache list for a while, which is avoided by calling
put_page() instead of putback_lru_page() in page migration's success
path. This means that this patch reverts a major change from commit add05cecef80 about the new refcounting rule of soft-offlined pages, so
"reuse window" revives. This will be closed by a subsequent patch.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Dean Nelson <dnelson@redhat.com> Cc: Tony Luck <tony.luck@intel.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Hugh Dickins <hughd@google.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Thu, 6 Aug 2015 22:47:04 +0000 (15:47 -0700)]
mm/memory-failure: give up error handling for non-tail-refcounted thp
"non anonymous thp" case is still racy with freeing thp, which causes
panic due to put_page() for refcount-0 page. It seems that closing up
this race might be hard (and/or not worth doing,) so let's give up the
error handling for this case.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Dean Nelson <dnelson@redhat.com> Cc: Tony Luck <tony.luck@intel.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Hugh Dickins <hughd@google.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Thu, 6 Aug 2015 22:47:01 +0000 (15:47 -0700)]
mm/memory-failure: fix race in counting num_poisoned_pages
When memory_failure() is called on a page which are just freed after
page migration from soft offlining, the counter num_poisoned_pages is
raised twi= ce. So let's fix it with using TestSetPageHWPoison.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Dean Nelson <dnelson@redhat.com> Cc: Tony Luck <tony.luck@intel.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Hugh Dickins <hughd@google.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Thu, 6 Aug 2015 22:46:58 +0000 (15:46 -0700)]
mm/memory-failure: unlock_page before put_page
Recently I addressed a few of hwpoison race problems and the patches are
merged on v4.2-rc1. It made progress, but unfortunately some problems
still remain due to less coverage of my testing. So I'm trying to fix
or avoid them in this series.
One point I'm expecting to discuss is that patch 4/5 changes the page
flag set to be checked on free time. In current behavior, __PG_HWPOISON
is not supposed to be set when the page is freed. I think that there is
no strong reason for this behavior, and it causes a problem hard to fix
only in error handler side (because __PG_HWPOISON could be set at
arbitrary timing.) So I suggest to change it.
With this patchset, hwpoison stress testing in official mce-test
testsuite (which previously failed) passes.
This patch (of 5):
In "just unpoisoned" path, we do put_page and then unlock_page, which is
a wrong order and causes "freeing locked page" bug. So let's fix it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Dean Nelson <dnelson@redhat.com> Cc: Tony Luck <tony.luck@intel.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Hugh Dickins <hughd@google.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Smalley [Thu, 6 Aug 2015 22:46:55 +0000 (15:46 -0700)]
ipc: use private shmem or hugetlbfs inodes for shm segments.
The shm implementation internally uses shmem or hugetlbfs inodes for shm
segments. As these inodes are never directly exposed to userspace and
only accessed through the shm operations which are already hooked by
security modules, mark the inodes with the S_PRIVATE flag so that inode
security initialization and permission checking is skipped.
This was motivated by the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
4.2.0-0.rc3.git0.1.fc24.x86_64+debug #1 Tainted: G W
-------------------------------------------------------
httpd/1597 is trying to acquire lock:
(&ids->rwsem){+++++.}, at: shm_close+0x34/0x130
but task is already holding lock:
(&mm->mmap_sem){++++++}, at: SyS_shmdt+0x4b/0x180
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&mm->mmap_sem){++++++}:
lock_acquire+0xc7/0x270
__might_fault+0x7a/0xa0
filldir+0x9e/0x130
xfs_dir2_block_getdents.isra.12+0x198/0x1c0 [xfs]
xfs_readdir+0x1b4/0x330 [xfs]
xfs_file_readdir+0x2b/0x30 [xfs]
iterate_dir+0x97/0x130
SyS_getdents+0x91/0x120
entry_SYSCALL_64_fastpath+0x12/0x76
-> #2 (&xfs_dir_ilock_class){++++.+}:
lock_acquire+0xc7/0x270
down_read_nested+0x57/0xa0
xfs_ilock+0x167/0x350 [xfs]
xfs_ilock_attr_map_shared+0x38/0x50 [xfs]
xfs_attr_get+0xbd/0x190 [xfs]
xfs_xattr_get+0x3d/0x70 [xfs]
generic_getxattr+0x4f/0x70
inode_doinit_with_dentry+0x162/0x670
sb_finish_set_opts+0xd9/0x230
selinux_set_mnt_opts+0x35c/0x660
superblock_doinit+0x77/0xf0
delayed_superblock_init+0x10/0x20
iterate_supers+0xb3/0x110
selinux_complete_init+0x2f/0x40
security_load_policy+0x103/0x600
sel_write_load+0xc1/0x750
__vfs_write+0x37/0x100
vfs_write+0xa9/0x1a0
SyS_write+0x58/0xd0
entry_SYSCALL_64_fastpath+0x12/0x76
...
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Reported-by: Morten Stevens <mstevens@fedoraproject.org> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Paul Moore <paul@paul-moore.com> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 6 Aug 2015 22:46:51 +0000 (15:46 -0700)]
mm: initialize hotplugged pages as reserved
Commit 92923ca3aace ("mm: meminit: only set page reserved in the
memblock region") broke memory hotplug which expects the memmap for
newly added sections to be reserved until onlined by
online_pages_range(). This patch marks hotplugged pages as reserved
when adding new zones.
Signed-off-by: Mel Gorman <mgorman@suse.de> Reported-by: David Vrabel <david.vrabel@citrix.com> Tested-by: David Vrabel <david.vrabel@citrix.com> Cc: Nathan Zimmer <nzimmer@sgi.com> Cc: Robin Holt <holt@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Thu, 6 Aug 2015 22:46:48 +0000 (15:46 -0700)]
ocfs2: fix shift left overflow
When using a large volume, for example 9T volume with 2T already used,
frequent creation of small files with O_DIRECT when the IO is not
cluster aligned may clear sectors in the wrong place. This will cause
filesystem corruption.
This is because p_cpos is a u32. When calculating the corresponding
sector it should be converted to u64 first, otherwise it may overflow.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: <stable@vger.kernel.org> [4.0+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Kershner [Thu, 6 Aug 2015 22:46:45 +0000 (15:46 -0700)]
kthread: export kthread functions
The s-Par visornic driver, currently in staging, processes a queue being
serviced by the an s-Par service partition. We can get a message that
something has happened with the Service Partition, when that happens, we
must not access the channel until we get a message that the service
partition is back again.
The visornic driver has a thread for processing the channel, when we get
the message, we need to be able to park the thread and then resume it
when the problem clears.
We can do this with kthread_park and unpark but they are not exported
from the kernel, this patch exports the needed functions.
Signed-off-by: David Kershner <david.kershner@unisys.com> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Richard Weinberger <richard.weinberger@gmail.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Thu, 6 Aug 2015 22:46:42 +0000 (15:46 -0700)]
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
fsnotify_clear_marks_by_group_flags() can race with
fsnotify_destroy_marks() so that when fsnotify_destroy_mark_locked()
drops mark_mutex, a mark from the list iterated by
fsnotify_clear_marks_by_group_flags() can be freed and thus the next
entry pointer we have cached may become stale and we dereference free
memory.
Fix the problem by first moving marks to free to a special private list
and then always free the first entry in the special list. This method
is safe even when entries from the list can disappear once we drop the
lock.
Signed-off-by: Jan Kara <jack@suse.com> Reported-by: Ashish Sangwan <a.sangwan@samsung.com> Reviewed-by: Ashish Sangwan <a.sangwan@samsung.com> Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/slub: allow merging when SLAB_DEBUG_FREE is set
This patch fixes creation of new kmem-caches after enabling
sanity_checks for existing mergeable kmem-caches in runtime: before that
patch creation fails because unique name in sysfs already taken by
existing kmem-cache.
Unlike other debug options this doesn't change object layout and could
be enabled and disabled at any time.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Acked-by: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
signalfd: fix information leak in signalfd_copyinfo
This function may copy the si_addr_lsb field to user mode when it hasn't
been initialized, which can leak kernel stack data to user mode.
Just checking the value of si_code is insufficient because the same
si_code value is shared between multiple signals. This is solved by
checking the value of si_signo in addition to si_code.
signal: fix information leak in copy_siginfo_to_user
This function may copy the si_addr_lsb, si_lower and si_upper fields to
user mode when they haven't been initialized, which can leak kernel
stack data to user mode.
Just checking the value of si_code is insufficient because the same
si_code value is shared between multiple signals. This is solved by
checking the value of si_signo in addition to si_code.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
signal: fix information leak in copy_siginfo_from_user32
This function can leak kernel stack data when the user siginfo_t has a
positive si_code value. The top 16 bits of si_code descibe which fields
in the siginfo_t union are active, but they are treated inconsistently
between copy_siginfo_from_user32, copy_siginfo_to_user32 and
copy_siginfo_to_user.
copy_siginfo_from_user32 is called from rt_sigqueueinfo and
rt_tgsigqueueinfo in which the user has full control overthe top 16 bits
of si_code.
This fixes the following information leaks:
x86: 8 bytes leaked when sending a signal from a 32-bit process to
itself. This leak grows to 16 bytes if the process uses x32.
(si_code = __SI_CHLD)
x86: 100 bytes leaked when sending a signal from a 32-bit process to
a 64-bit process. (si_code = -1)
sparc: 4 bytes leaked when sending a signal from a 32-bit process to a
64-bit process. (si_code = any)
parsic and s390 have similar bugs, but they are not vulnerable because
rt_[tg]sigqueueinfo have checks that prevent sending a positive si_code
to a different process. These bugs are also fixed for consistency.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Thu, 6 Aug 2015 22:46:23 +0000 (15:46 -0700)]
ocfs2: fix BUG in ocfs2_downconvert_thread_do_work()
The "BUG_ON(list_empty(&osb->blocked_lock_list))" in
ocfs2_downconvert_thread_do_work can be triggered in the following case:
ocfs2dc has firstly saved osb->blocked_lock_count to local varibale
processed, and then processes the dentry lockres. During the dentry
put, it calls iput and then deletes rw, inode and open lockres from
blocked list in ocfs2_mark_lockres_freeing. And this causes the
variable `processed' to not reflect the number of blocked lockres to be
processed, which triggers the BUG.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 6 Aug 2015 22:46:20 +0000 (15:46 -0700)]
fs, file table: reinit files_stat.max_files after deferred memory initialisation
Dave Hansen reported the following;
My laptop has been behaving strangely with 4.2-rc2. Once I log
in to my X session, I start getting all kinds of strange errors
from applications and see this in my dmesg:
VFS: file-max limit 8192 reached
The problem is that the file-max is calculated before memory is fully
initialised and miscalculates how much memory the kernel is using. This
patch recalculates file-max after deferred memory initialisation. Note
that using memory hotplug infrastructure would not have avoided this
problem as the value is not recalculated after memory hot-add.
Nicolai Stange [Thu, 6 Aug 2015 22:46:16 +0000 (15:46 -0700)]
mm, meminit: replace rwsem with completion
Commit 0e1cc95b4cc7 ("mm: meminit: finish initialisation of struct pages
before basic setup") introduced a rwsem to signal completion of the
initialization workers.
Lockdep complains about possible recursive locking:
=============================================
[ INFO: possible recursive locking detected ] 4.1.0-12802-g1dc51b8 #3 Not tainted
---------------------------------------------
swapper/0/1 is trying to acquire lock:
(pgdat_init_rwsem){++++.+},
at: [<ffffffff8424c7fb>] page_alloc_init_late+0xc7/0xe6
but task is already holding lock:
(pgdat_init_rwsem){++++.+},
at: [<ffffffff8424c772>] page_alloc_init_late+0x3e/0xe6
Replace the rwsem by a completion together with an atomic
"outstanding work counter".
[peterz@infradead.org: Barrier removal on the grounds of being pointless]
[mgorman@suse.de: Applied review feedback] Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Alex Ng <alexng@microsoft.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 6 Aug 2015 22:46:13 +0000 (15:46 -0700)]
mm, meminit: allow early_pfn_to_nid to be used during runtime
early_pfn_to_nid() historically was inherently not SMP safe but only
used during boot which is inherently single threaded or during hotplug
which is protected by a giant mutex.
With deferred memory initialisation there was a thread-safe version
introduced and the early_pfn_to_nid would trigger a BUG_ON if used
unsafely. Memory hotplug hit that check. This patch makes
early_pfn_to_nid introduces a lock to make it safe to use during
hotplug.
Signed-off-by: Mel Gorman <mgorman@suse.de> Reported-by: Alex Ng <alexng@microsoft.com> Tested-by: Alex Ng <alexng@microsoft.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Nicolai Stange <nicstange@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marcus Gelderie [Thu, 6 Aug 2015 22:46:10 +0000 (15:46 -0700)]
ipc: modify message queue accounting to not take kernel data structures into account
A while back, the message queue implementation in the kernel was
improved to use btrees to speed up retrieval of messages, in commit d6629859b36d ("ipc/mqueue: improve performance of send/recv").
That patch introducing the improved kernel handling of message queues
(using btrees) has, as a by-product, changed the meaning of the QSIZE
field in the pseudo-file created for the queue. Before, this field
reflected the size of the user-data in the queue. Since, it also takes
kernel data structures into account. For example, if 13 bytes of user
data are in the queue, on my machine the file reports a size of 61
bytes.
There was some discussion on this topic before (for example
https://lkml.org/lkml/2014/10/1/115). Commenting on a th lkml, Michael
Kerrisk gave the following background
(https://lkml.org/lkml/2015/6/16/74):
The pseudofiles in the mqueue filesystem (usually mounted at
/dev/mqueue) expose fields with metadata describing a message
queue. One of these fields, QSIZE, as originally implemented,
showed the total number of bytes of user data in all messages in
the message queue, and this feature was documented from the
beginning in the mq_overview(7) page. In 3.5, some other (useful)
work happened to break the user-space API in a couple of places,
including the value exposed via QSIZE, which now includes a measure
of kernel overhead bytes for the queue, a figure that renders QSIZE
useless for its original purpose, since there's no way to deduce
the number of overhead bytes consumed by the implementation.
(The other user-space breakage was subsequently fixed.)
This patch removes the accounting of kernel data structures in the
queue. Reporting the size of these data-structures in the QSIZE field
was a breaking change (see Michael's comment above). Without the QSIZE
field reporting the total size of user-data in the queue, there is no
way to deduce this number.
It should be noted that the resource limit RLIMIT_MSGQUEUE is counted
against the worst-case size of the queue (in both the old and the new
implementation). Therefore, the kernel overhead accounting in QSIZE is
not necessary to help the user understand the limitations RLIMIT imposes
on the processes.
Signed-off-by: Marcus Gelderie <redmnic@gmail.com> Acked-by: Doug Ledford <dledford@redhat.com> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Acked-by: Davidlohr Bueso <dbueso@suse.de> Cc: David Howells <dhowells@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: John Duffy <jb_duffy@btinternet.com> Cc: Arto Bendiken <arto@bendiken.net> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Qu Wenruo [Mon, 3 Aug 2015 06:44:29 +0000 (14:44 +0800)]
btrfs: qgroup: Fix a regression in qgroup reserved space.
During the change to new btrfs extent-oriented qgroup implement, due to
it doesn't use the old __qgroup_excl_accounting() for exclusive extent,
it didn't free the reserved bytes.
The bug will cause limit function go crazy as the reserved space is
never freed, increasing limit will have no effect and still cause
EQOUT.
The fix is easy, just free reserved bytes for newly created exclusive
extent as what it does before.
Reported-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com> Signed-off-by: Yang Dongsheng <yangds.fnst@cn.fujitsu.com> Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
David Weinehall [Tue, 4 Aug 2015 13:55:52 +0000 (16:55 +0300)]
drm/i915: Allow parsing of variable size child device entries from VBT
VBT version 196 increased the size of common_child_dev_config. The parser
code assumed that the size of this structure would not change.
The modified code now copies the amount needed based on the VBT version,
and emits a debug message if the VBT version is unknown (too new);
since the struct config block won't shrink in newer versions it should
be harmless to copy the maximum known size in such cases, so that's
what we do, but emitting the warning is probably sensible anyway.
In the longer run it might make sense to modify the parser code to
use a version/feature mapping, rather than hardcoding things like this,
but for now the variants are fairly managable.
Mengdong Lin [Wed, 5 Aug 2015 13:41:14 +0000 (14:41 +0100)]
ASoC: topology: Add ops support to byte controls UAPI
Add UAPI support for setting byte control ops. Rename the ops structure
to be more generic so it can be sued by other objects too.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Mengdong Lin [Wed, 5 Aug 2015 13:41:13 +0000 (14:41 +0100)]
ASoC: topology: Update TLV support so we can support more TLV types
Currently the TLV topology structure is targeted at only supporting the
DB scale data. This patch extends support for the other TLV types so they
can be easily added at a later stage.
TLV structure is moved to common topology control header since it's a
common field for controls and can be processed in a general way.
Users must set a proper access flag for a control since it's used to
decide if the TLV field is valid and if a TLV callback is needed.
Removed the following fields from topology TLV struct:
- size/count: type can decide the size.
- numid: not needed to initialize TLV for kcontrol.
- data: replaced by the type specific struct.
Added TLV structure to generic control header and removed TLV structure
from mixer control.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Thu, 6 Aug 2015 11:34:41 +0000 (12:34 +0100)]
Merge tag 'asoc-fix-v4.2-rc3' into asoc-fix-topology
ASoC: Fixes for v4.2
A lot of small fixes here, a few to the core:
- Fix for binding DAPM stream widgets on devices with prefixes assigned
to them
- Minor fixes for the newly added topology interfaces
- Locking and memory leak fixes for DAPM
- Driver specific fixes
Vinod Koul [Mon, 29 Jun 2015 16:36:46 +0000 (17:36 +0100)]
ASoC: topology: add private data to manifest
The topology file manifest should include a private data field. This
allows vendors to specify vendor data in the manifest, like
timestamps, hashes, additional information for removing platform
configuration out of drivers and making these configurable per platform
Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Alban Bedel [Tue, 4 Aug 2015 08:59:17 +0000 (10:59 +0200)]
usb: ehci-platform: Fix using multiple controllers from OF
When using OF defined controllers the platform data struct is shared
between all devices, so it can't be used for device specific settings.
However it is currently used for the OF properties
needs-reset-on-resume and has-transaction-translator.
To fix this issue move setting hcd->has_tt to the probe and
move pdata->reset_on_resume to the private data.
Signed-off-by: Alban Bedel <albeu@free.fr> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Iooss [Sat, 1 Aug 2015 13:55:38 +0000 (21:55 +0800)]
drm/amdgpu: increment queue when iterating on this variable.
gfx_v7_0_print_status contains a for loop on variable queue which does
not update this variable between each iteration. This is bug is
reported by clang while building allmodconfig LLVMLinux on x86_64:
drivers/gpu/drm/amd/amdgpu/gfx_v7_0.c:5126:19: error: variable
'queue' used in loop condition not modified in loop body
[-Werror,-Wloop-analysis]
for (queue = 0; queue < 8; i++) {
^~~~~
Fix this by incrementing variable queue instead of i in this loop.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Wed, 5 Aug 2015 15:50:38 +0000 (18:50 +0300)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Just two very small & simple patches"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MTRR: Use default type for non-MTRR-covered gfn before WARN_ON
KVM: s390: Fix hang VCPU hang/loop regression
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
projects / linux-beck.git / log