Besides the CPU and DDR PLLs, the CPU and DDR frequencies
can be derived from other PLLs in the SRIF block on the
AR934x SoCs. The current code does not checks if the SRIF
PLLs are used and this can lead to incorrectly calculated
CPU/DDR frequencies.
Fix it by calculating the frequencies from SRIF PLLs if
those are used on a given board.
And, the check "if (datalen < sizeof(struct pktgen_hdr))" will be
passed as "datalen" is promoted to unsigned, therefore will cause
a crash later.
This is a quick fix by checking if "datalen" is negative. The following
patch will increase the default value of 'min_pkt_size' for IPv6.
This bug should exist for a long time, so Cc -stable too.
Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible to miss data when using the kdb pager. The kdb pager
does not pay attention to the maximum column constraint of the screen
or serial terminal. This result is not incrementing the shown lines
correctly and the pager will print more lines that fit on the screen.
Obviously that is less than useful when using a VGA console where you
cannot scroll back.
The pager will now look at the kdb_buffer string to see how many
characters are printed. It might not be perfect considering you can
output ASCII that might move the cursor position, but it is a
substantially better approximation for viewing dmesg and trace logs.
This also means that the vt screen needs to set the kdb COLUMNS
variable.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few places free skbs using dev_kfree_skb even though they're called
after ieee80211_subif_start_xmit might have cloned it for tracking tx
status. Use ieee80211_free_txskb here to prevent skb leaks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using ieee80211_free_txskb for tx frames is required, since mac80211 clones
skbs for which socket tx status is requested.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we stop the tick in idle, we save the current jiffies value
in ts->idle_jiffies. This snapshot is substracted from the later
value of jiffies when the tick is restarted and the resulting
delta is accounted as idle cputime. This is how we handle the
idle cputime accounting without the tick.
But sometimes we need to schedule the next tick to some time in
the future instead of completely stopping it. In this case, a
tick may happen before we restart the periodic behaviour and
from that tick we account one jiffy to idle cputime as usual but
we also increment the ts->idle_jiffies snapshot by one so that
when we compute the delta to account, we substract the one jiffy
we just accounted.
To prepare for stopping the tick outside idle, we introduced a
check that prevents from fixing up that ts->idle_jiffies if we
are not running the idle task. But we use idle_cpu() for that
and this is a problem if we run the tick while another CPU
remotely enqueues a ttwu to our runqueue:
CPU 0: CPU 1:
tick_sched_timer() { ttwu_queue_remote()
if (idle_cpu(CPU 0))
ts->idle_jiffies++;
}
Here, idle_cpu() notes that &rq->wake_list is not empty and
hence won't consider the CPU as idle. As a result,
ts->idle_jiffies won't be incremented. But this is wrong because
we actually account the current jiffy to idle cputime. And that
jiffy won't get substracted from the nohz time delta. So in the
end, this jiffy is accounted twice.
Fix this by changing idle_cpu(smp_processor_id()) with
is_idle_task(current). This way the jiffy is substracted
correctly even if a ttwu operation is enqueued on the CPU.
Adding two (or more) timers with large values for "expires" (they have
to reside within tv5 in the same list) leads to endless looping
between cascade() and internal_add_timer() in case CONFIG_BASE_SMALL
is one and jiffies are crossing the value 1 << 18. The bug was
introduced between 2.6.11 and 2.6.12 (and survived for quite some
time).
This patch ensures that when cascade() is called timers within tv5 are
not added endlessly to their own list again, instead they are added to
the next lower tv level tv4 (as expected).
As detailed in the thread titled "viafb PLL/clock tweaking causes XO-1.5
instability," enabling or disabling the IGA1/IGA2 clocks causes occasional
stability problems during suspend/resume cycles on this platform.
This is rather odd, as the documentation suggests that clocks have two
states (on/off) and the default (stable) configuration is configured to
enable the clock only when it is needed. However, explicitly enabling *or*
disabling the clock triggers this system instability, suggesting that there
is a 3rd state at play here.
Leaving the clock enable/disable registers alone solves this problem.
This fixes spurious reboots during suspend/resume behaviour introduced by
commit b692a63a.
Line 0 and 1 were both written to line 0 (on the display) and all subsequent
lines had an offset of -1. The result was that the last line on the display
was never overwritten by writes to /dev/fbN.
Cloudlinux have a product called lve that includes a kernel module. This
was previously GPLed but is now under a proprietary license, but the
module continues to declare MODULE_LICENSE("GPL") and makes use of some
EXPORT_SYMBOL_GPL symbols. Forcibly taint it in order to avoid this.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Alex Lyashkov <umka@cloudlinux.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In autofs4_d_automount(), if a mount fail occurs the AUTOFS_INF_PENDING
mount pending flag is not cleared.
One effect of this is when using the "browse" option, directory entry
attributes show up with all "?"s due to the incorrect callback and
subsequent failure return (when in fact no callback should be made).
Signed-off-by: Ian Kent <ikent@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A queue newly allocated with blk_alloc_queue_node() has only
QUEUE_FLAG_BYPASS set. For request-based drivers,
blk_init_allocated_queue() is called and q->queue_flags is overwritten
with QUEUE_FLAG_DEFAULT which doesn't include BYPASS even though the
initial bypass is still in effect.
In blk_init_allocated_queue(), or QUEUE_FLAG_DEFAULT to q->queue_flags
instead of overwriting.
The hypervisor will trap it. However without this patch,
we would crash as the .read_tscp is set to NULL. This patch
fixes it and sets it to the native_read_tscp call.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 254d1a3f02ebc10ccc6e4903394d8d3f484f715e, titled
"xen/pv-on-hvm kexec: shutdown watches from old kernel" assumes that the
XenBus backend can deal with reading of values from:
"control/platform-feature-xs_reset_watches":
... a patch for xenstored is required so that it
accepts the XS_RESET_WATCHES request from a client (see changeset
23839:42a45baf037d in xen-unstable.hg). Without the patch for xenstored
the registration of watches will fail and some features of a PVonHVM
guest are not available. The guest is still able to boot, but repeated
kexec boots will fail."
Sadly this is not true when using a Xen 3.4 hypervisor and booting a PVHVM
guest. We end up hanging at:
Reverting the commit or using the attached patch fixes the issue. This fix
checks whether the hypervisor is older than 4.0 and if so does not try to
perform the read.
Fixes-Oracle-Bug: 14708233 Acked-by: Olaf Hering <olaf@aepfle.de>
[v2: Added a comment in the source code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The virq_disabled flag tracks the userspace view of INTx masking
across interrupt mode changes, but we're not consistently applying
this to the interrupt and masking handler notion of the device.
Currently if the user sets DisINTx while in MSI or MSIX mode, then
returns to INTx mode (ex. rebooting a qemu guest), the hardware has
DisINTx+, but the management of INTx thinks it's enabled, making it
impossible to actually clear DisINTx. Fix this by updating the
handler state when INTx is re-enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to be ready to recieve an interrupt as soon as we call
request_irq, so our eventfd context setting needs to be moved
earlier. Without this, an interrupt from our device or one
sharing the interrupt line can pass a NULL into eventfd_signal
and oops.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qla2xxx firmware actually expects the task management response
code in a CTIO IOCB with SCSI status mode 1 to be in little-endian
byte order, ie the response code should be the first byte in the
sense_data[] array. The old code erroneously byte-swapped the
response code, which puts it in the wrong place on the wire and leads
to initiators thinking every task management request succeeds (since
they see 0 in the byte where they look for the response code).
Signed-off-by: Roland Dreier <roland@purestorage.com> Cc: Chad Dupuis <chad.dupuis@qlogic.com> Cc: Arun Easi <arun.easi@qlogic.com> Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch re-adds the ability to optionally run in buffered FILEIO mode
(eg: w/o O_DSYNC) for device backends in order to once again use the
Linux buffered cache as a write-back storage mechanism.
This logic was originally dropped with mainline v3.5-rc commit:
target/file: Use O_DSYNC by default for FILEIO backends
This difference with this patch is that fd_create_virtdevice() now
forces the explicit setting of emulate_write_cache=1 when buffered FILEIO
operation has been enabled.
(v2: Switch to FDBD_HAS_BUFFERED_IO_WCE + add more detailed
comment as requested by hch)
Reported-by: Ferry <iscsitmp@bananateam.nl> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes error cases within target_core_init_configfs() to
properly set ret = -ENOMEM before jumping to the out_global exception
path.
This was originally discovered with the following Coccinelle semantic
match information:
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function. A simplified version of the semantic match
that finds this problem is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INQUIRY processing already uses an on-heap bounce buffer for loopback,
but not for other fabrics. Switch this to a cheaper on-stack bounce
buffer, similar to the one used by MODE SENSE and REQUEST SENSE, and
use it unconditionally. With this in place, zero allocation length is
handled simply by checking the return address of transport_kmap_data_sg.
Testcase: sg_raw /dev/sdb 12 00 83 00 00 00
should fail with ILLEGAL REQUEST / INVALID FIELD IN CDB sense
does not fail without the patch
fails correctly with the series
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two bugs of the /dev/fw* character device concerning the
FW_CDEV_IOC_GET_INFO ioctl with nonzero fw_cdev_get_info.bus_reset.
(Practically all /dev/fw* clients issue this ioctl right after opening
the device.)
Both bugs are caused by sizeof(struct fw_cdev_event_bus_reset) being 36
without natural alignment and 40 with natural alignment.
1) Memory corruption, affecting i386 userland on amd64 kernel:
Userland reserves a 36 bytes large buffer, kernel writes 40 bytes.
This has been first found and reported against libraw1394 if
compiled with gcc 4.7 which happens to order libraw1394's stack such
that the bug became visible as data corruption.
2) Information leak, affecting all kernel architectures except i386:
4 bytes of random kernel stack data were leaked to userspace.
Hence limit the respective copy_to_user() to the 32-bit aligned size of
struct fw_cdev_event_bus_reset.
Reported-by: Simon Kirby <sim@hostway.ca> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
read_persistent_clock uses a global variable, use a spinlock to
ensure non-atomic updates to the variable don't overlap and cause
time to move backwards.
Signed-off-by: Colin Cross <ccross@android.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Workaround for the 775420 Cortex-A9 (r2p2, r2p6,r2p8,r2p10,r3p0) erratum.
In case a date cache maintenance operation aborts with MMU exception, it
might cause the processor to deadlock. This workaround puts DSB before
executing ISB if an abort may occur on cache maintenance.
Based on work by Kouei Abe and feedback from Catalin Marinas.
Signed-off-by: Kouei Abe <kouei.abe.cp@rms.renesas.com>
[ horms@verge.net.au: Changed to implementation
suggested by catalin.marinas@arm.com ] Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sg struct is used without being initialized, which breaks
when CONFIG_DEBUG_SG is enabled.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently it is possible to unmap one more block than user requested to
due to the off-by-one error in unmap_region(). This is probably due to
the fact that the end variable despite its name actually points to the
last block to unmap + 1. However in the condition it is handled as the
last block of the region to unmap.
The bug was not previously spotted probably due to the fact that the
region was not zeroed, which has changed with commit be1dd78de5686c062bb3103f9e86d444a10ed783. With that commit we were able
to corrupt the ext4 file system on 256M scsi_debug device with LBPRZ
enabled using fstrim.
Since the 'end' semantic is the same in several functions there this
commit just fixes the condition to use the 'end' variable correctly in
that context.
Reported-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Lukas Czerner <lczerner@redhat.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly account for I/O in transit before returning from the RESET call.
In the absense of this patch, we could have a situation where the host may
respond to a command that was issued prior to the issuance of the RESET
command at some arbitrary time after responding to the RESET command.
Currently, the host does not do anything with the RESET command.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch increases the default for nopin_timeout to 15 seconds (wait
between sending a new NopIN ping) and nopin_response_timeout to 30 seconds
(wait for NopOUT response before failing the connection) in order to avoid
false positives by iSCSI Initiators who are not always able (under load) to
respond to NopIN echo PING requests within the current 5 second window.
False positives have been observed recently using Open-iSCSI code on v3.3.x
with heavy large-block READ workloads over small MTU 1 Gb/sec ports, and
increasing these values to more reasonable defaults significantly reduces
the possibility of false positive NopIN response timeout events under
this specific workload.
Historically these have been set low to initiate connection recovery as
soon as possible if we don't hear a ping back, but for modern v3.x code
on 1 -> 10 Gb/sec ports these new defaults make alot more sense.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <michaelc@cs.wisc.edu> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've had reports in the past about this specific case, so it's time to
go ahead and explicitly set cache_dynamic_acls=1 for generate_node_acls=1
(TPG demo-mode) operation.
During normal generate_node_acls=0 operation with explicit NodeACLs ->
se_node_acl memory is persistent to the configfs group located at
/sys/kernel/config/target/$TARGETNAME/$TPGT/acls/$INITIATORNAME, so in
the generate_node_acls=1 case we want the reservation logic to reference
existing per initiator IQN se_node_acl memory (not to generate a new
se_node_acl), so go ahead and always set cache_dynamic_acls=1 when
TPG demo-mode is enabled.
Reported-by: Ronnie Sahlberg <ronniesahlberg@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a potential multiple spin-unlock -> deadlock scenario during the
overflow check within iscsit_build_sendtargets_resp() as found by
sparse static checking.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a missing iscsi_reject->ffffffff assignment within
iscsit_send_reject() code to properly follow RFC-3720 Section 10.17
Bytes 16 -> 19 for the PDU format definition of ISCSI_OP_REJECT.
We've not seen any initiators care about this bytes in practice, but
as Ronnie reported this was causing trouble with wireshark packet
decoding lets go ahead and fix this up now.
Reported-by: Ronnie Sahlberg <ronniesahlberg@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fuzzing with trinity oopsed on the 1st instruction of shmem_fh_to_dentry(),
u64 inum = fid->raw[2];
which is unhelpfully reported as at the end of shmem_alloc_inode():
Right, tmpfs is being stupid to access fid->raw[2] before validating that
fh_len includes it: the buffer kmalloc'ed by do_sys_name_to_handle() may
fall at the end of a page, and the next page not be present.
But some other filesystems (ceph, gfs2, isofs, reiserfs, xfs) are being
careless about fh_len too, in fh_to_dentry() and/or fh_to_parent(), and
could oops in the same way: add the missing fh_len checks to those.
Reported-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Sage Weil <sage@inktank.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fault was detected using the kgdb test suite on boot and it
crashes recursively due to the fact that CONFIG_KPROBES on mips adds
an extra die notifier in the page fault handler. The crash signature
looks like this:
kgdbts:RUN bad memory access test
KGDB: re-enter exception: ALL breakpoints killed
Call Trace:
[<807b7548>] dump_stack+0x20/0x54
[<807b7548>] dump_stack+0x20/0x54
The fix for now is to have kgdb return immediately if the fault type
is DIE_PAGE_FAULT and allow the kprobe code to decide what is supposed
to happen.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit [4b527b65 ALSA: hda - limit internal mic boost for Asus
X202E] introduced the use of auto-parser code, but it forgot to add
struct hda_gen_spec at the head of codec->spec which the auto-parser
assumes silently. Without this record, it may result in memory
corruption.
By enlarging the GPE storm threshold back to 20, that laptop's
EC works fine with interrupt mode instead of polling mode.
https://bugzilla.kernel.org/show_bug.cgi?id=45151
Reported-and-Tested-by: Francesco <trentini@dei.unipd.it> Signed-off-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux EC driver includes a mechanism to detect GPE storms,
and switch from interrupt-mode to polling mode. However, polling
mode sometimes doesn't work, so the workaround is problematic.
Also, different systems seem to need the threshold for detecting
the GPE storm at different levels.
ACPI_EC_STORM_THRESHOLD was initially 20 when it's created, and
was changed to 8 in 2.6.28 commit 06cf7d3c7 "ACPI: EC: lower interrupt storm
threshold" to fix kernel bug 11892 by forcing the laptop in that bug to
work in polling mode. However in bug 45151, it works fine in interrupt
mode if we lift the threshold back to 20.
This patch makes the threshold a module parameter so that user has a
flexible option to debug/workaround this issue.
The default is unchanged.
This is also a preparation patch to fix specific systems:
https://bugzilla.kernel.org/show_bug.cgi?id=45151
Signed-off-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NSM RPC client can be required on NFSv3 umount, when child reaper is dying
(and destroying it's mount namespace). It means, that current nsproxy is set
to NULL already, but creation of RPC client requires UTS namespace for gaining
hostname string.
This patch creates reference-counted per-net NSM client on first monitor
request and destroys it after last unmonitor request.
Taking hostname from uts namespace if not safe, because this cuold be
performind during umount operation on child reaper death. And in this case
current->nsproxy is NULL already.
NSM RPC client can be required on NFSv3 umount, when child reaper is dying (and
destroying it's mount namespace). It means, that current nsproxy is set to
NULL already, but creation of RPC client requires UTS namespace for gaining
hostname string.
This patch introduces reference counted NFS RPC clients creation and
destruction helpers (similar to RPCBIND RPC clients).
Processes that open and close multiple files may end up setting this
oo_last_closed_stid without freeing what was previously pointed to.
This can result in a major leak, visible for example by watching the
nfsd4_stateids line of /proc/slabinfo.
Reported-by: Cyril B. <cbay@excellency.fr> Tested-by: Cyril B. <cbay@excellency.fr> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I added cr_flavor to the data compared in same_creds without any
justification, in d5497fc693a446ce9100fcf4117c3f795ddfd0d2 "nfsd4: move
rq_flavor into svc_cred".
Recent client changes then started making
mount -osec=krb5 server:/export /mnt/
echo "hello" >/mnt/TMP
umount /mnt/
mount -osec=krb5i server:/export /mnt/
echo "hello" >/mnt/TMP
to fail due to a clid_inuse on the second open.
Mounting sequentially like this with different flavors probably isn't
that common outside artificial tests. Also, the real bug here may be
that the server isn't just destroying the former clientid in this case
(because it isn't good enough at recognizing when the old state is
gone). But it prompted some discussion and a look back at the spec, and
I think the check was probably wrong. Fix and document.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I put the client into an open recovery loop by:
Client: Open file
read half
Server: Expire client (echo 0 > /sys/kernel/debug/nfsd/forget_clients)
Client: Drop vm cache (echo 3 > /proc/sys/vm/drop_caches)
finish reading file
This causes a loop because the client never updates the nfs4_state after
discovering that the delegation is invalid. This means it will keep
trying to read using the bad delegation rather than attempting to re-open
the file.
After commit e38eb650 (NFS: set_pnfs_layoutdriver() from
nfs4_proc_fsinfo()), set_pnfs_layoutdriver() is called inside
nfs4_proc_fsinfo(), but pnfs_blksize is not set. It causes setting
blocklayoutdriver failure and pnfsblock mount failure.
If applications use flock to protect its write range, generic NFS
will not do read-modify-write cycle at page cache level. Therefore
LD should know how to handle non-sector aligned writes. Otherwise
there will be data corruption.
Michael Olbrich reported that his test program fails when built with
-O2 -mcpu=cortex-a8 -mfpu=neon, and a kernel which supports v6 and v7
CPUs:
volatile int x = 2;
volatile int64_t y = 2;
int main() {
volatile int a = 0;
volatile int64_t b = 0;
while (1) {
a = (a + x) % (1 << 30);
b = (b + y) % (1 << 30);
assert(a == b);
}
}
and two instances are run. When built for just v7 CPUs, this program
works fine. It uses the "vadd.i64 d19, d18, d16" VFP instruction.
It appears that we do not save the high-16 double VFP registers across
context switches when the kernel is built for v6 CPUs. Fix that.
Tested-By: Michael Olbrich <m.olbrich@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wchar_t is currently 16bit so converting a utf8 encoded characters not
in plane 0 (>= 0x10000) to wchar_t (that is calling char2uni) lead to a
-EINVAL return. This patch detect utf8 in cifs_strtoUTF16 and add special
code calling utf8s_to_utf16s.
Signed-off-by: Frediano Ziglio <frediano.ziglio@citrix.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
JFFS2 was designed without thought for OOB bitflips, it seems, but they
can occur and will be reported to JFFS2 via mtd_read_oob()[1]. We don't
want to fail on these transactions, since the data was corrected.
[1] Few drivers report bitflips for OOB-only transactions. With such
drivers, this patch should have no effect.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes regression introduced by
"8bdc81c jffs2: get rid of jffs2_sync_super". We submit a delayed work in order
to make sure the write-buffer is synchronized at some point. But we do not
flush it when we unmount, which causes an oops when we unmount the file-system
and then the delayed work is executed.
This patch fixes the issue by adding a "cancel_delayed_work_sync()" infocation
in the '->sync_fs()' handler. This will make sure the delayed work is canceled
on sync, unmount and re-mount. And because VFS always callse 'sync_fs()' before
unmounting or remounting, this fixes the issue.
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious
interrupts without any active request. To prevent the Oops, that results
in such cases, don't dereference the mmc request pointer until we make
sure, that we are indeed processing such a request.
mmc_gpio_request_ro() doesn't store the requested gpio in ctx->ro_gpio.
As a result, subsequent calls to mmc_gpio_get_ro() will always fail
with -ENOSYS because the gpio number isn't available to that function.
In some cases mmc_suspend_host() is not able to claim the
host and proceed with the suspend process. The core returns
-EBUSY to the host controller driver. Unfortunately, the
host controller driver does not pass on this information
to the PM core and hence the system suspend process continues.
ret = mmc_suspend_host(host->mmc);
if (ret) {
host->suspended = 0;
if (host->pdata->resume) {
ret = host->pdata->resume(dev, host->slot_id);
The return status from mmc_suspend_host() is overwritten by return
status from host->pdata->resume. So the original return status is lost.
In these cases the MMC core gets to an unexpected state
during resume and multiple issues related to MMC crop up.
1. Host controller driver starts accessing the device registers
before the clocks are enabled which leads to a prefetch abort.
2. A file copy thread which was launched before suspend gets
stuck due to the host not being reclaimed during resume.
To avoid such problems pass on the -EBUSY status to the PM core
from the host controller driver. With this change, MMC core
suspend might still fail but it does not end up making the
system unusable. Suspend gets aborted and the user can try
suspending the system again.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com> Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Acked-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unloading the omap2 nand driver missed to release the memory region which will
result in not being able to request it again if one want to load the driver
later on.
This patch fixes following error when loading omap2 module after unloading:
---8<---
~ $ rmmod omap2
~ $ modprobe omap2
[ 37.420928] omap2-nand: probe of omap2-nand.0 failed with error -16
~ $
--->8---
Do not kfree() the mtd_info; it is handled in the mtd subsystem and
already freed by nand_release(). Instead kfree() the struct
omap_nand_info allocated in omap_nand_probe which was not freed before.
This patch fixes following error when unloading the omap2 module:
Update driver autcpu12-nvram.c so it compiles; map_read32/map_write32
no longer exist in the kernel so the driver is totally broken.
Additionally, map_info name passed to simple_map_init is incorrect.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may cause a memory leak when the @types has more then one parser.
Take the `default_mtd_part_types` for example. The default_mtd_part_types has
two parsers now: `cmdlinepart` and `ofpart`.
Assume the following case:
The kernel command line sets the partitions like:
#gpmi-nand:20m(boot),20m(kernel),1g(rootfs),-(user)
But the devicetree file(such as arch/arm/boot/dts/imx28-evk.dts) also sets
the same partitions as the kernel command line does.
In the current code, the partitions parsed out by the `ofpart` will
overwrite the @pparts which has already set by the `cmdlinepart` parser,
and the the partitions parsed out by the `cmdlinepart` is missed.
A memory leak occurs.
So we should break the code as soon as we parse out the partitions,
In actually, this patch makes a priority order between the parsers.
If one parser has already parsed out the partitions successfully,
it's no need to use another parser anymore.
There was a race condition when the system suspends while hda_power_work
is running in the work queue. If system suspend (snd_hda_suspend)
happens after the work queue releases power_lock but before it calls
hda_call_codec_suspend, codec_suspend runs with power_on=0, causing the
codec to power up for register reads, and hanging when it calls
cancel_delayed_work_sync from the running work queue.
The call chain from the work queue will look like this:
hda_power_work <<- power_on = 1, unlock, then power_on cleard by suspend
hda_call_codec_suspend
hda_set_power_state
snd_hda_codec_read
codec_exec_verb
snd_hda_power_up
snd_hda_power_save
__snd_hda_power_up
cancel_delayed_work_sync <<-- cancelling executing wq
Fix this by waiting for the work queue to finish before starting suspend
if suspend is not happening on the work queue.
This dongle ships with the X1 Carbon, and has an AX88772B
usb to ethernet chip in it.
Signed-off-by: Quinlan Pfiffer <qpfiffer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f319da0c68 ("sched: Fix load avg vs cpu-hotplug") was an
incomplete fix:
In particular, the problem is that at the point it calls
calc_load_migrate() nr_running := 1 (the stopper thread), so move the
call to CPU_DEAD where we're sure that nr_running := 0.
Also note that we can call calc_load_migrate() without serialization, we
know the state of rq is stable since its cpu is dead, and we modify the
global state using appropriate atomic ops.
Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1346882630.2600.59.camel@twins Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch initializes a value of efi.runtime_version at boot time.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com> Acked-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Ivan Hu <ivan.hu@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't assume the presence of the red zone while we're still in a boot
services environment, so we should build with -fno-red-zone to avoid
problems. Change the size of wchar at the same time to make string handling
simpler.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Acked-by: Josh Boyer <jwboyer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cc9a6c877661 ("cpuset: mm: reduce large amounts of memory barrier
related damage v3") introduced a potential memory corruption.
shmem_alloc_page() uses a pseudo vma and it has one significant unique
combination, vma->vm_ops=NULL and vma->policy->flags & MPOL_F_SHARED.
get_vma_policy() does NOT increase a policy ref when vma->vm_ops=NULL
and mpol_cond_put() DOES decrease a policy ref when a policy has
MPOL_F_SHARED. Therefore, when a cpuset update race occurs,
alloc_pages_vma() falls in 'goto retry_cpuset' path, decrements the
reference count and frees the policy prematurely.
When shared_policy_replace() fails to allocate new->policy is not freed
correctly by mpol_set_shared_policy(). The problem is that shared
mempolicy code directly call kmem_cache_free() in multiple places where
it is easy to make a mistake.
This patch creates an sp_free wrapper function and uses it. The bug was
introduced pre-git age (IOW, before 2.6.12-rc2).
shared_policy_replace() use of sp_alloc() is unsafe. 1) sp_node cannot
be dereferenced if sp->lock is not held and 2) another thread can modify
sp_node between spin_unlock for allocating a new sp node and next
spin_lock. The bug was introduced before 2.6.12-rc2.
Kosaki's original patch for this problem was to allocate an sp node and
policy within shared_policy_replace and initialise it when the lock is
reacquired. I was not keen on this approach because it partially
duplicates sp_alloc(). As the paths were sp->lock is taken are not that
performance critical this patch converts sp->lock to sp->mutex so it can
sleep when calling sp_alloc().
The problem is that the structure is being prematurely freed due to a
reference count imbalance. In the following case mbind(addr, len) should
replace the memory policies of both vma1 and vma2 and thus they will
become to share the same mempolicy and the new mempolicy will have the
MPOL_F_SHARED flag.
alloc_pages_vma() uses get_vma_policy() and mpol_cond_put() pair for
maintaining the mempolicy reference count. The current rule is that
get_vma_policy() only increments refcount for shmem VMA and
mpol_conf_put() only decrements refcount if the policy has
MPOL_F_SHARED.
In above case, vma1 is not shmem vma and vma->policy has MPOL_F_SHARED!
The reference count will be decreased even though was not increased
whenever alloc_page_vma() is called. This has been broken since commit
[52cd3b07: mempolicy: rework mempolicy Reference Counting] in 2008.
There is another serious bug with the sharing of memory policies.
Currently, mempolicy rebind logic (it is called from cpuset rebinding)
ignores a refcount of mempolicy and override it forcibly. Thus, any
mempolicy sharing may cause mempolicy corruption. The bug was
introduced by commit [68860ec1: cpusets: automatic numa mempolicy
rebinding].
Ideally, the shared policy handling would be rewritten to either
properly handle COW of the policy structures or at least reference count
MPOL_F_SHARED based exclusively on information within the policy.
However, this patch takes the easier approach of disabling any policy
sharing between VMAs. Each new range allocated with sp_alloc will
allocate a new policy, set the reference count to 1 and drop the
reference count of the old policy. This increases the memory footprint
but is not expected to be a major problem as mbind() is unlikely to be
used for fine-grained ranges. It is also inefficient because it means
we allocate a new policy even in cases where mbind_range() could use the
new_policy passed to it. However, it is more straight-forward and the
change should be invisible to the user.
[mgorman@suse.de: Edited changelog] Reported-by: Dave Jones <davej@redhat.com>, Cc: Christoph Lameter <cl@linux.com>, Reviewed-by: Christoph Lameter <cl@linux.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: Josh Boyer <jwboyer@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 05f144a0d5c2 ("mm: mempolicy: Let vma_merge and vma_split handle
vma->vm_policy linkages") removed vma->vm_policy updates code but it is
the purpose of mbind_range(). Now, mbind_range() is virtually a no-op
and while it does not allow memory corruption it is not the right fix.
This patch is a revert.
Each grace period is supposed to have at least one callback waiting
for that grace period to complete. However, if CONFIG_NO_HZ=n, an
extra callback-free grace period is no big problem -- it will chew up
a tiny bit of CPU time, but it will complete normally. In contrast,
CONFIG_NO_HZ=y kernels have the potential for all the CPUs to go to
sleep indefinitely, in turn indefinitely delaying completion of the
callback-free grace period. Given that nothing is waiting on this grace
period, this is also not a problem.
That is, unless RCU CPU stall warnings are also enabled, as they are
in recent kernels. In this case, if a CPU wakes up after at least one
minute of inactivity, an RCU CPU stall warning will result. The reason
that no one noticed until quite recently is that most systems have enough
OS noise that they will never remain absolutely idle for a full minute.
But there are some embedded systems with cut-down userspace configurations
that consistently get into this situation.
All this begs the question of exactly how a callback-free grace period
gets started in the first place. This can happen due to the fact that
CPUs do not necessarily agree on which grace period is in progress.
If a CPU still believes that the grace period that just completed is
still ongoing, it will believe that it has callbacks that need to wait for
another grace period, never mind the fact that the grace period that they
were waiting for just completed. This CPU can therefore erroneously
decide to start a new grace period. Note that this can happen in
TREE_RCU and TREE_PREEMPT_RCU even on a single-CPU system: Deadlock
considerations mean that the CPU that detected the end of the grace
period is not necessarily officially informed of this fact for some time.
Once this CPU notices that the earlier grace period completed, it will
invoke its callbacks. It then won't have any callbacks left. If no
other CPU has any callbacks, we now have a callback-free grace period.
This commit therefore makes CPUs check more carefully before starting a
new grace period. This new check relies on an array of tail pointers
into each CPU's list of callbacks. If the CPU is up to date on which
grace periods have completed, it checks to see if any callbacks follow
the RCU_DONE_TAIL segment, otherwise it checks to see if any callbacks
follow the RCU_WAIT_TAIL segment. The reason that this works is that
the RCU_WAIT_TAIL segment will be promoted to the RCU_DONE_TAIL segment
as soon as the CPU is officially notified that the old grace period
has ended.
This change is to cpu_needs_another_gp(), which is called in a number
of places. The only one that really matters is in rcu_start_gp(), where
the root rcu_node structure's ->lock is held, which prevents any
other CPU from starting or completing a grace period, so that the
comparison that determines whether the CPU is missing the completion
of a grace period is stable.
Reported-by: Becky Bruce <bgillbruce@gmail.com> Reported-by: Subodh Nijsure <snijsure@grid-net.com> Reported-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Paul Walmsley <paul@pwsan.com> # OMAP3730, OMAP4430 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in scores's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chen Liqin <liqin.chen@sunplusct.com> Cc: Lennox Wu <lennox.wu@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the m32r's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Hirokazu Takata <takata@linux-m32r.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the Cris's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mikael Starvik <starvik@axis.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Cris <linux-cris-kernel@axis.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the Alpha's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Tested-by: Michael Cree <mcree@orcon.net.nz> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Cc: alpha <linux-alpha@vger.kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the m68k's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: m68k <linux-m68k@lists.linux-m68k.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the mn10300's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: David Howells <dhowells@redhat.com> Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: David Howells <dhowells@redhat.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the Frv's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: David Howells <dhowells@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the xtensa's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Zankel <chris@zankel.net> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the parisc's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: James E.J. Bottomley <jejb@parisc-linux.org> Cc: Helge Deller <deller@gmx.de> Cc: Parisc <linux-parisc@vger.kernel.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the h8300's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Traditionally, the entire idle task served as an RCU quiescent state.
But when RCU read side critical sections started appearing within the
idle loop, this traditional strategy became untenable. The fix was to
create new RCU APIs named rcu_idle_enter() and rcu_idle_exit(), which
must be called by each architecture's idle loop so that RCU can tell
when it is safe to ignore a given idle CPU.
Unfortunately, this fix was never applied to ia64, a shortcoming remedied
by this commit.
Reported by: Tony Luck <tony.luck@intel.com> Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested by: Tony Luck <tony.luck@intel.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I can't even find how I figured this might be needed anymore. But sure
enough, the value I'm reading back on platforms doesn't match what the
docs recommends.
It seemed to fix Chris' GT1 in limited testing as well.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... since finish_page_flip needs the vblank timestamp generated
in drm_handle_vblank. Somehow all the gmch platforms get it right,
but all the pch platform irq handlers get is wrong. Hooray for copy&
pasting!
Currently this gets papered over by a gross hack in finish_page_flip.
A second patch will remove that.
Note that without this, the new timestamp sanity checks in flip_test
occasionally get tripped up, hence the cc: stable tag.
Reviewed-by: mario.kleiner@tuebingen.mpg.de Tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was meant to be the purpose of the
intel_crtc_wait_for_pending_flips() function which is called whilst
preparing the CRTC for a modeset or before disabling. However, as Ville
Syrjala pointed out, we set the pending flip notification on the old
framebuffer that is no longer attached to the CRTC by the time we come
to flush the pending operations. Instead, we can simply wait on the
pending unpin work to be finished on this CRTC, knowning that the
hardware has therefore finished modifying the registers, before proceeding
with our direct access.
Fixes i-g-t/flip_test on non-pch platforms. pch platforms simply
schedule the flip immediately when the pipe is disabled, leading
to other funny issues.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added i-g-t note and cc: stable] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MIP_ADDRESS should point to the resolved FMASK for an MSAA texture.
Setting MIP_ADDRESS to 0 means the FMASK pointer is invalid (the GPU
won't read the memory then).
The userspace has to set MIP_ADDRESS to 0 and *not* emit any relocation
for it.
Signed-off-by: Marek Olšák <maraeo@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As during the plane cleanup, we wish to disable the hardware and
so may modify state on the associated CRTC, that CRTC must continue to
exist until we are finished.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54101 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Tested-by: lu hua <huax.lu@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes some unfortunate races on resume. The G84 version of the code doesn't
need this as "gpuobj"s are automagically suspended/resumed by the core code
whereas pinned buffer objects are not.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log