James Hogan [Thu, 31 Jan 2013 13:27:35 +0000 (13:27 +0000)]
metag: make TXPRIVEXT bits explicit
Define PRIV_BITS using explicit constants from <asm/metag_regs.h> rather
than with a hard coded value. This also adds a couple of missing
definitions for the TXPRIVEXT priv bits for protecting writes to TXTIMER
and the trace registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Thu, 31 Jan 2013 11:06:03 +0000 (11:06 +0000)]
metag: add boot time LNKGET/LNKSET check
Add boot time check for whether LNKGET/LNKSET go through or around the
cache. Depending on the configuration an info message (no harm), warning
(technically wrong but no harm), or big WARN (expect failure in either
kernel or userland) may be emitted if the behaviour is not as expected:
Configuration Hardware Response
------------------------------------------ -------- --------
AROUND_CACHE through pr_info
!AROUND_CACHE && ATOMICITY_LNKGET around WARN (kernel)
" && !ATOMICITY_LNKGET && SMP around WARN (user)
" " && !SMP around pr_warn
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Fri, 21 Sep 2012 16:38:15 +0000 (17:38 +0100)]
metag: Add JTAG Debug Adapter (DA) support
Add basic JTAG Debug Adapter (DA) support so that drivers which
communicate with the DA can detect whether one is actually present
(otherwise the target will halt indefinitely).
This allows the metag_da TTY driver and imgdafs filesystem driver to be
built, updates defconfigs, and sets up the metag_da console early if
it's configured in.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Wed, 5 Dec 2012 11:34:13 +0000 (11:34 +0000)]
Kconfig.debug: add METAG to dependency lists
Add [!]METAG to a couple of Kconfig dependencies in lib/Kconfig.debug.
Don't allow stack utilization instrumentation on metag, and allow
building with frame pointers.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: "Paul E. McKenney" <paul.mckenney@linaro.org> Cc: Akinobu Mita <akinobu.mita@gmail.com> Cc: Michel Lespinasse <walken@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com>
The above commit combined several arch-specific vma flags into one, and
in the process it changed the VM_GROWSUP definition to depend on
specific architectures rather than CONFIG_STACK_GROWSUP. Therefore add
an ifdef for CONFIG_METAG to also set VM_GROWSUP.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Michel Lespinasse <walken@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-mm@kvack.org
James Hogan [Tue, 9 Oct 2012 10:00:27 +0000 (11:00 +0100)]
metag: Basic documentation
Add basic metag documentation. This includes an outline description of
the ABIs (including syscall ABI) and calling conventions, similar to the
one in Documentation/frv/.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Rob Landley <rob@landley.net> Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: linux-doc@vger.kernel.org
James Hogan [Tue, 9 Oct 2012 10:00:24 +0000 (11:00 +0100)]
metag: Atomics, locks and bitops
Add header files to implement Meta hardware thread locks (used by some
other atomic operations), atomics, spinlocks, and bitops.
There are 2 main types of atomic primitives for metag (in addition to
IRQs off on UP):
- LOCK instructions provide locking between hardware threads.
- LNKGET/LNKSET instructions provide load-linked/store-conditional
operations allowing for lighter weight atomics on Meta2
LOCK instructions allow for hardware threads to acquire voluntary or
exclusive hardware thread locks:
- LOCK0 releases exclusive and voluntary lock from the running hardware
thread.
- LOCK1 acquires the voluntary hardware lock, blocking until it becomes
available.
- LOCK2 implies LOCK1, and additionally acquires the exclusive hardware
lock, blocking all other hardware threads from executing.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Tue, 9 Oct 2012 09:54:51 +0000 (10:54 +0100)]
metag: System Calls
Add metag system call and gateway page interfaces. The metag
architecture port uses the generic system call numbers from
asm-generic/unistd.h, as well as a user gateway page mapped at
0x6ffff000 which contains fast atomic primitives (depending on SMP) and
a fast method of accessing TLS data.
System calls use the SWITCH instruction with the immediate 0x440001 to
signal a system call.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Tue, 9 Oct 2012 09:54:47 +0000 (10:54 +0100)]
metag: Internal and external irqchips
Meta core internal interrupts (from HWSTATMETA and friends) are vectored
onto the TR1 core trigger for the current thread. This is demultiplexed
in irq-metag.c to individual Linux IRQs for each internal interrupt.
External SoC interrupts (from HWSTATEXT and friends) are vectored onto
the TR2 core trigger for the current thread. This is demultiplexed in
irq-metag-ext.c to individual Linux IRQs for each external SoC interrupt.
The external irqchip has devicetree bindings for configuring the number
of irq banks and the type of masking available.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Rob Landley <rob@landley.net> Cc: Dom Cobley <popcornmix@gmail.com> Cc: Simon Arlott <simon@fire.lp0.eu> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: devicetree-discuss@lists.ozlabs.org Cc: linux-doc@vger.kernel.org
James Hogan [Tue, 9 Oct 2012 09:54:43 +0000 (10:54 +0100)]
metag: Traps
Add trap code for metag. At the lowest level Meta traps (and return from
interrupt instruction - RTI) simply swap the PC and PCX registers and
optionally toggle the interrupt status bit (ISTAT). Low level TBX code
in tbipcx.S handles the core context save, determine the TBX signal
number based on the core trigger that fired (using the TXSTATI status
register), and call TBX signal handlers (mostly in traps.c) via a vector
table.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Al Viro <viro@zeniv.linux.org.uk>
James Hogan [Tue, 9 Oct 2012 09:54:39 +0000 (10:54 +0100)]
metag: Time keeping
Add time keeping code for metag. Meta hardware threads have 2 timers.
The background timer (TXTIMER) is used as a free-running time base, and
the interrupt timer (TXTIMERI) is used for the timer interrupt. Both
counters traditionally count at approximately 1MHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: John Stultz <johnstul@us.ibm.com> Cc: Thomas Gleixner <tglx@linutronix.de>
James Hogan [Tue, 9 Oct 2012 09:54:36 +0000 (10:54 +0100)]
metag: ptrace
The ptrace interface for metag provides access to some core register
sets using the PTRACE_GETREGSET and PTRACE_SETREGSET operations. The
details of the internal context structures is abstracted into user API
structures to both ease use and allow flexibility to change the internal
context layouts. Copyin and copyout functions for these register sets
are exposed to allow signal handling code to use them to copy to and
from the signal context.
struct user_gp_regs (NT_PRSTATUS) provides access to the core general
purpose register context.
struct user_cb_regs (NT_METAG_CBUF) provides access to the TXCATCH*
registers which contains information abuot a memory fault, unaligned
access error or watchpoint. This can be modified to alter the way the
fault is replayed on resume ("catch replay"), or to prevent the replay
taking place.
struct user_rp_state (NT_METAG_RPIPE) provides access to the state of
the Meta read pipeline which can be used to hide memory latencies in
hand optimised data loops.
Extended DSP register state, DSP RAM, and hardware breakpoint registers
aren't yet exposed through ptrace.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Denys Vlasenko <vda.linux@googlemail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Tony Lindgren <tony@atomide.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
James Hogan [Tue, 9 Oct 2012 09:54:17 +0000 (10:54 +0100)]
metag: Memory handling
Meta has instructions for accessing:
- bytes - GETB (1 byte)
- words - GETW (2 bytes)
- doublewords - GETD (4 bytes)
- longwords - GETL (8 bytes)
All accesses must be aligned. Unaligned accesses can be detected and
made to fault on Meta2, however it isn't possible to fix up unaligned
writes so we don't bother fixing up reads either.
This patch adds metag memory handling code including:
- I/O memory (io.h, ioremap.c): Actually any virtual memory can be
accessed with these helpers. A part of the non-MMUable address space
is used for memory mapped I/O. The ioremap() function is implemented
one to one for non-MMUable addresses.
- User memory (uaccess.h, usercopy.c): User memory is directly
accessible from privileged code.
- Kernel memory (maccess.c): probe_kernel_write() needs to be
overwridden to use the I/O functions when doing a simple aligned
write to non-writecombined memory, otherwise the write may be split
by the generic version.
Note that due to the fact that a portion of the virtual address space is
non-MMUable, and therefore always maps directly to the physical address
space, metag specific I/O functions are made available (metag_in32,
metag_out32 etc). These cast the address argument to a pointer so that
they can be used with raw physical addresses. These accessors are only
to be used for accessing fixed core Meta architecture registers in the
non-MMU region, and not for any SoC/peripheral registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Tue, 9 Oct 2012 09:54:17 +0000 (10:54 +0100)]
metag: Memory management
Add memory management files for metag.
Meta's 32bit virtual address space is split into two halves:
- local (0x08000000-0x7fffffff): traditionally local to a hardware
thread and incoherent between hardware threads. Each hardware thread
has it's own local MMU table. On Meta2 the local space can be
globally coherent (GCOn) if the cache partitions coincide.
- global (0x88000000-0xffff0000): coherent and traditionally global
between hardware threads. On Meta2, each hardware thread has it's own
global MMU table.
The low 128MiB of each half is non-MMUable and maps directly to the
physical address space:
- 0x00010000-0x07ffffff: contains Meta core registers and maps SoC bus
- 0x80000000-0x87ffffff: contains low latency global core memories
Linux usually further splits the local virtual address space like this:
- 0x08000000-0x3fffffff: user mappings
- 0x40000000-0x7fffffff: kernel mappings
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Tue, 9 Oct 2012 09:54:17 +0000 (10:54 +0100)]
metag: Cache/TLB handling
Add cache and TLB handling code for metag, including the required
callbacks used by MM switches and DMA operations. Caches can be
partitioned between the hardware threads and the global space, however
this is usually configured by the bootloader so Linux doesn't make any
changes to this configuration. TLBs aren't configurable, so only need
consideration to flush them.
On Meta1 the L1 cache was VIVT which required a full flush on MM switch.
Meta2 has a VIPT L1 cache so it doesn't require the full flush on MM
switch. Meta2 can also have a writeback L2 with hardware prefetch which
requires some special handling. Support is optional, and the L2 can be
detected and initialised by Linux.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Fri, 21 Sep 2012 16:38:15 +0000 (17:38 +0100)]
metag: Boot
Add boot code for metag. Due to the multi-threaded nature of Meta it is
not uncommon for an RTOS or bare metal application to be started on
other hardware threads by the bootloader. Since there is a single MMU
switch which affects all threads, the MMU is traditionally configured by
the bootloader prior to starting Linux. The bootloader passes a
structure to Linux which among other things contains information about
memory regions which have been mapped. Linux then assumes control of the
local heap memory region.
A kernel arguments string pointer or a flattened device tree pointer can
be provided in the third argument.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Wed, 5 Dec 2012 11:03:52 +0000 (11:03 +0000)]
metag: Headers for core arch constants
Add a couple of header files containing core architecture constants.
The first (<asm/metag_isa.h>) contains some constants relating to the
instruction set, such as values to give to the CACHEW and CACHER
instructions.
The second (<asm/metag_regs.h>) contains constants for the core register
units directly accessible to various instructions, and for the
registers, fields, and bits in those units. The main units described are
the control unit (CT.*), the trigger unit (TR.*), and the run-time trace
unit (TT.*).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Wed, 30 May 2012 11:11:19 +0000 (12:11 +0100)]
trace/ring_buffer: handle 64bit aligned structs
Some 32 bit architectures require 64 bit values to be aligned (for
example Meta which has 64 bit read/write instructions). These require 8
byte alignment of event data too, so use
!CONFIG_HAVE_64BIT_ALIGNED_ACCESS instead of !CONFIG_64BIT ||
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to decide alignment, and align
buffer_data_page::data accordingly.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@redhat.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> (previous version subtly different)
James Hogan [Wed, 30 May 2012 10:23:23 +0000 (11:23 +0100)]
Add HAVE_64BIT_ALIGNED_ACCESS
On 64 bit architectures with no efficient unaligned access, padding and
explicit alignment must be added in various places to prevent unaligned
64bit accesses (such as taskstats and trace ring buffer).
However this also needs to apply to 32 bit architectures with 64 bit
accesses requiring alignment such as metag.
This is solved by adding a new Kconfig symbol HAVE_64BIT_ALIGNED_ACCESS
which defaults to 64BIT && !HAVE_EFFICIENT_UNALIGNED_ACCESS, and can be
explicitly selected by METAG and any other relevant architectures. This
can be used in various places to determine whether 64bit alignment is
required.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Eric Paris <eparis@redhat.com> Cc: Will Drewry <wad@chromium.org>
James Hogan [Mon, 9 May 2011 09:58:40 +0000 (10:58 +0100)]
Revert some of "binfmt_elf: cleanups"
The commit "binfmt_elf: cleanups"
(f670d0ecda73b7438eec9ed108680bc5f5362ad8) removed an ifndef elf_map but
this breaks compilation for metag which does define elf_map.
This adds the ifndef back in as it was before, but does not affect the
other cleanups made by that patch.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Acked-by: Mikael Pettersson <mikpe@it.uu.se>
James Hogan [Fri, 24 Feb 2012 13:47:48 +0000 (13:47 +0000)]
asm-generic/unistd.h: handle symbol prefixes in cond_syscall
Some architectures have symbol prefixes and set CONFIG_SYMBOL_PREFIX,
but this wasn't taken into account by the generic cond_syscall. It's
easy enough to fix in a generic fashion, so add the symbol prefix to
symbol names in cond_syscall when CONFIG_SYMBOL_PREFIX is set.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
James Hogan [Fri, 23 Nov 2012 16:13:05 +0000 (16:13 +0000)]
asm-generic/io.h: check CONFIG_VIRT_TO_BUS
Make asm-generic/io.h check CONFIG_VIRT_TO_BUS before defining
virt_to_bus() and bus_to_virt(), otherwise it's easy to accidentally
have a silently failing incorrect direct mapped definition rather then
no definition at all.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Mon, 18 Feb 2013 17:58:02 +0000 (09:58 -0800)]
mm: fix pageblock bitmap allocation
Commit c060f943d092 ("mm: use aligned zone start for pfn_to_bitidx
calculation") fixed out calculation of the index into the pageblock
bitmap when a !SPARSEMEM zome was not aligned to pageblock_nr_pages.
However, the _allocation_ of that bitmap had never taken this alignment
requirement into accout, so depending on the exact size and alignment of
the zone, the use of that index could then access past the allocation,
resulting in some very subtle memory corruption.
This was reported (and bisected) by Ingo Molnar: one of his random
config builds would hang with certain very specific kernel command line
options.
In the meantime, commit c060f943d092 has been marked for stable, so this
fix needs to be back-ported to the stable kernels that backported the
commit to use the right alignment.
Linus Torvalds [Fri, 15 Feb 2013 20:12:55 +0000 (12:12 -0800)]
Merge tag 'stable/for-linus-3.8-rc7-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes:
- A simple bug-fix for redundant NULL check.
- CVE-2013-0228/XSA-42: x86/xen: don't assume %ds is usable in
xen_iret for 32-bit PVOPS
and two reverts:
- Revert the PVonHVM kexec. The patch introduces a regression with
older hypervisor stacks, such as Xen 4.1."
* tag 'stable/for-linus-3.8-rc7-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
Revert "xen PVonHVM: use E820_Reserved area for shared_info"
Revert "xen/PVonHVM: fix compile warning in init_hvm_pv_info"
xen: remove redundant NULL check before unregister_and_remove_pcpu().
x86/xen: don't assume %ds is usable in xen_iret for 32-bit PVOPS.
Revert "[media] dvb_frontend: return -ENOTTY for unimplement IOCTL"
As reported by Klaus Schmidinger:
"In VDR I use an ioctl() call with FE_READ_UNCORRECTED_BLOCKS on a
device (using stb0899). After this call I check 'errno' for
EOPNOTSUPP to determine whether this device supports this call. This
used to work just fine, until a few months ago I noticed that my
devices using stb0899 didn't display their signal quality in VDR's OSD
any more. After further investigation I found that
ioctl(FE_READ_UNCORRECTED_BLOCKS) no longer returns EOPNOTSUPP, but
rather ENOTTY. And since I stop getting the signal quality in case
any unknown errno value appears, this broke my signal quality query
function."
Linus Torvalds [Fri, 15 Feb 2013 20:04:57 +0000 (12:04 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull one more x86 fix from Peter Anvin:
"Sigh. One more patch in the "please don't brick my Samsung" series"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Clear EFI_RUNTIME_SERVICES rather than EFI_BOOT by "noefi" boot parameter
Linus Torvalds [Fri, 15 Feb 2013 20:04:08 +0000 (12:04 -0800)]
Merge tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This is another fix for v3.8. It fixes an oops that happens when a
Thunderbolt adapter is unplugged (remove device, poll for PME events
on no-longer-existing device, oops)."
* tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Clean up PME state when removing a device
Linus Torvalds [Fri, 15 Feb 2013 20:03:09 +0000 (12:03 -0800)]
Merge tag 'omapdss-for-3.8-rc8' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss fixes from Tomi Valkeinen:
"It'd be great if these two late fixes would still make it into 3.8.
The other one fixes ARM kernel compilation when using 'allyesconfig',
and the other makes DPI displays function again on OMAP3630 boards:
- Fix ARM compilation with "allyesconfig" (omapdrm: fix the
dependency to omapdss)
- fix DPI displays on OMAP3630 (OMAPDSS: add FEAT_DPI_USES_VDDS_DSI
to omap3630_dss_feat_list)"
* tag 'omapdss-for-3.8-rc8' of git://gitorious.org/linux-omap-dss2/linux:
omapdrm: fix the dependency to omapdss
OMAPDSS: add FEAT_DPI_USES_VDDS_DSI to omap3630_dss_feat_list
Linus Torvalds [Fri, 15 Feb 2013 19:59:27 +0000 (11:59 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c maintainer info update from Wolfram Sang:
"Since my old email and repos are not working anymore, and this already
caused some confusion, I think a MAINTAINERS update for 3.8 is
helpful. So, people trying I2C with the new kernel can properly reach
me and find my repos."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: change my email and repos
We are doing this b/c on 32-bit PVonHVM with older hypervisors
(Xen 4.1) it ends up bothing up the start_info. This is bad b/c
we use it for the time keeping, and the timekeeping code loops
forever - as the version field never changes. Olaf says to
revert it, so lets do that.
Acked-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tomi Valkeinen [Thu, 7 Feb 2013 14:35:52 +0000 (16:35 +0200)]
omapdrm: fix the dependency to omapdss
omapdrm uses "select" in Kconfig to enable omapdss. This doesn't work
correctly, as "select" forces omapdss to be enabled in the config even
if it normally could not be enabled because of missing Kconfig
dependencies.
This causes a build break on ARM, when using allyesconfig:
drivers/video/omap2/dss/dss.c: In function 'dss_calc_clock_div':
drivers/video/omap2/dss/dss.c:572:20: error: 'CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK' undeclared (first use in this function)
drivers/video/omap2/dss/dss.c:572:20: note: each undeclared identifier is reported only once for each function it appears in
Instead of using select, this patch changes omapdrm to use "depend
on".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Satoru Takeuchi [Thu, 14 Feb 2013 00:12:52 +0000 (09:12 +0900)]
efi: Clear EFI_RUNTIME_SERVICES rather than EFI_BOOT by "noefi" boot parameter
There was a serious problem in samsung-laptop that its platform driver is
designed to run under BIOS and running under EFI can cause the machine to
become bricked or can cause Machine Check Exceptions.
Discussion about this problem:
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
https://bugzilla.kernel.org/show_bug.cgi?id=47121
Unfortunately this problem comes back again if users specify "noefi" option.
This parameter clears EFI_BOOT and that driver continues to run even if running
under EFI. Refer to the document, this parameter should clear
EFI_RUNTIME_SERVICES instead.
Documentation/x86/x86_64/uefi.txt:
===============================================================================
...
- If some or all EFI runtime services don't work, you can try following
kernel command line parameters to turn off some or all EFI runtime
services.
noefi turn off all EFI runtime services
...
===============================================================================
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com> Link: http://lkml.kernel.org/r/511C2C04.2070108@jp.fujitsu.com Cc: Matt Fleming <matt.fleming@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Jan Beulich [Thu, 24 Jan 2013 13:11:10 +0000 (13:11 +0000)]
x86/xen: don't assume %ds is usable in xen_iret for 32-bit PVOPS.
This fixes CVE-2013-0228 / XSA-42
Drew Jones while working on CVE-2013-0190 found that that unprivileged guest user
in 32bit PV guest can use to crash the > guest with the panic like this:
Petr says: "
I've analysed the bug and I think that xen_iret() cannot cope with
mangled DS, in this case zeroed out (null selector/descriptor) by either
xen_failsafe_callback() or RESTORE_REGS because the corresponding LDT
entry was invalidated by the reproducer. "
Jan took a look at the preliminary patch and came up a fix that solves
this problem:
"This code gets called after all registers other than those handled by
IRET got already restored, hence a null selector in %ds or a non-null
one that got loaded from a code or read-only data descriptor would
cause a kernel mode fault (with the potential of crashing the kernel
as a whole, if panic_on_oops is set)."
The way to fix this is to realize that the we can only relay on the
registers that IRET restores. The two that are guaranteed are the
%cs and %ss as they are always fixed GDT selectors. Also they are
inaccessible from user mode - so they cannot be altered. This is
the approach taken in this patch.
Another alternative option suggested by Jan would be to relay on
the subtle realization that using the %ebp or %esp relative references uses
the %ss segment. In which case we could switch from using %eax to %ebp and
would not need the %ss over-rides. That would also require one extra
instruction to compensate for the one place where the register is used
as scaled index. However Andrew pointed out that is too subtle and if
further work was to be done in this code-path it could escape folks attention
and lead to accidents.
Reviewed-by: Petr Matousek <pmatouse@redhat.com> Reported-by: Petr Matousek <pmatouse@redhat.com> Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
David S. Miller [Wed, 13 Feb 2013 20:21:06 +0000 (12:21 -0800)]
sparc64: Fix get_user_pages_fast() wrt. THP.
Mostly mirrors the s390 logic, as unlike x86 we don't need the
SetPageReferenced() bits.
On sparc64 we also lack a user/privileged bit in the huge PMDs.
In order to make this work for THP and non-THP builds, some header
file adjustments were necessary. Namely, provide the PMD_HUGE_* bit
defines and the pmd_large() inline unconditionally rather than
protected by TRANSPARENT_HUGEPAGE.
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"This is primarily to get those r8169 reverts sorted, but other fixes
have accumulated meanwhile.
1) Revert two r8169 changes to fix suspend/resume for some users,
from Francois Romieu.
2) PCI dma mapping errors in atl1c are not checked for and this cause
hard crashes for some users, from Xiong Huang.
3) In 3.8.x we merged the removal of the EXPERIMENTAL dependency for
'dlm' but the same patch for 'sctp' got lost somewhere, resulting
in the potential for build errors since there are cross
dependencies. From Kees Cook.
4) SCTP's ipv6 socket route validation makes boolean tests
incorrectly, fix from Daniel Borkmann.
5) mac80211 does sizeof(ptr) instead of (sizeof(ptr) * nelem), from
Cong Ding.
6) arp_rcv() can crash on shared non-linear packets, from Eric
Dumazet.
7) Avoid crashes in macvtap by setting ->gso_type consistently in
ixgbe, qlcnic, and bnx2x drivers. From Michael S Tsirkin and
Alexander Duyck.
8) Trinity fuzzer spots infinite loop in __skb_recv_datagram(), fix
from Eric Dumazet.
9) STP protocol frames should use high packet priority, otherwise an
overloaded bridge can get stuck. From Stephen Hemminger.
10) The HTB packet scheduler was converted some time ago to store
internal timestamps in nanoseconds, but we don't convert back into
psched ticks for the user during dumps. Fix from Jiri Pirko.
11) mwl8k channel table doesn't set the .band field properly,
resulting in NULL pointer derefs. Fix from Jonas Gorski.
12) mac80211 doesn't accumulate channels properly during a scan so we
can downgrade heavily to a much less desirable connection speed.
Fix from Johannes Berg.
13) PHY probe failure in stmmac can result in resource leaks and
double MDIO registery later, from Giuseppe CAVALLARO.
14) Correct ipv6 checksumming in ip6t_NPT netfilter module, also fix
address prefix mangling, from YOSHIFUJI Hideaki."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net, sctp: remove CONFIG_EXPERIMENTAL
net: sctp: sctp_v6_get_dst: fix boolean test in dst cache
batman-adv: Fix NULL pointer dereference in DAT hash collision avoidance
net/macb: fix race with RX interrupt while doing NAPI
atl1c: add error checking for pci_map_single functions
htb: fix values in opt dump
ixgbe: Only set gso_type to SKB_GSO_TCPV4 as RSC does not support IPv6
net: fix infinite loop in __skb_recv_datagram()
net: qmi_wwan: add Yota / Megafon M100-1 4g modem
mwl8k: fix band for supported channels
bridge: set priority of STP packets
mac80211: fix channel selection bug
arp: fix possible crash in arp_rcv()
bnx2x: set gso_type
qlcnic: set gso_type
ixgbe: fix gso type
stmmac: mdio register has to fail if the phy is not found
stmmac: fix macro used for debugging the xmit
Revert "r8169: enable internal ASPM and clock request settings".
Revert "r8169: enable ALDPS for power saving".
...
Linus Torvalds [Wed, 13 Feb 2013 20:19:49 +0000 (12:19 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"One (hopefully) last batch of x86 fixes. You asked for the patch by
patch justifications, so here they are:
x86, MCE: Retract most UAPI exports
This one unexports from userspace a bunch of definitions which should
never have been exported. We really don't want to create an
accidental legacy here.
x86, doc: Add a bootloader ID for OVMF
This is a documentation-only patch, just recording the official
assignment of a boot loader ID.
x86: Do not leak kernel page mapping locations
Security: avoid making it needlessly easy for user space to probe the
kernel memory layout.
x86/mm: Check if PUD is large when validating a kernel address
Prevent failures using /proc/kcore when using 1G pages.
x86/apic: Work around boot failure on HP ProLiant DL980 G7 Server systems
Works around a BIOS problem causing boot failures on affected hardware."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Check if PUD is large when validating a kernel address
x86/apic: Work around boot failure on HP ProLiant DL980 G7 Server systems
x86, doc: Add a bootloader ID for OVMF
x86: Do not leak kernel page mapping locations
x86, MCE: Retract most UAPI exports
Wolfram Sang [Fri, 8 Feb 2013 19:54:40 +0000 (20:54 +0100)]
MAINTAINERS: change my email and repos
Change to my private email, change to my shiny new kernel.org repos,
and drop outdated entry from the former maintainer. Drop my PCA entry,
too, since it belongs to the I2C realm anyhow.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Devices are added to pci_pme_list when drivers use pci_enable_wake()
or pci_wake_from_d3(), but they aren't removed from the list unless
the driver explicitly disables wakeup. Many drivers never disable
wakeup, so their devices remain on the list even after they are
removed, e.g., via hotplug. A subsequent PME poll will oops when
it tries to touch the device.
This patch disables PME# on a device before removing it, which removes
the device from pci_pme_list. This is safe even if the device never
had PME# enabled.
This oops can be triggered by unplugging a Thunderbolt ethernet adapter
on a Macbook Pro, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2svG21yiM1wkH4_2pen2n+cr2-Zv7TbH3Gj+8MwevZjDbw@mail.gmail.com Reported-and-tested-by: Daniel J Blueman <daniel@quora.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org
Kees Cook [Wed, 13 Feb 2013 00:24:56 +0000 (16:24 -0800)]
net, sctp: remove CONFIG_EXPERIMENTAL
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 12 Feb 2013 13:30:16 +0000 (13:30 +0000)]
net: sctp: sctp_v6_get_dst: fix boolean test in dst cache
We walk through the bind address list and try to get the best source
address for a given destination. However, currently, we take the
'continue' path of the loop when an entry is invalid (!laddr->valid)
*and* the entry state does not equal SCTP_ADDR_SRC (laddr->state !=
SCTP_ADDR_SRC).
Thus, still, invalid entries with SCTP_ADDR_SRC might not 'continue'
as well as valid entries with SCTP_ADDR_{NEW, SRC, DEL}, with a possible
false baddr and matchlen as a result, causing in worst case dst route
to be false or possibly NULL.
This test should actually be a '||' instead of '&&'. But lets fix it
and make this a bit easier to read by having the condition the same way
as similarly done in sctp_v4_get_dst.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pau Koning [Tue, 12 Feb 2013 00:18:45 +0000 (00:18 +0000)]
batman-adv: Fix NULL pointer dereference in DAT hash collision avoidance
An entry in DAT with the hashed position of 0 can cause a NULL pointer
dereference when the first entry is checked by batadv_choose_next_candidate.
This first candidate automatically has the max value of 0 and the max_orig_node
of NULL. Not checking max_orig_node for NULL in batadv_is_orig_node_eligible
will lead to a NULL pointer dereference when checking for the lowest address.
Nicolas Ferre [Tue, 12 Feb 2013 10:08:48 +0000 (11:08 +0100)]
net/macb: fix race with RX interrupt while doing NAPI
When interrupts are disabled, an RX condition can occur but
it is not reported when enabling interrupts again. We need to check
RSR and use napi_reschedule() if condition is met.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong [Mon, 11 Feb 2013 14:44:40 +0000 (14:44 +0000)]
atl1c: add error checking for pci_map_single functions
it is reported that code hit DMA-API errors on 3.8-rc6+,
(see https://bugzilla.redhat.com/show_bug.cgi?id=908436, and
https://bugzilla.redhat.com/show_bug.cgi?id=908550)
this patch just adds error handler for
pci_map_single and skb_frag_dma_map.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Investigation determined that the bug triggered when reading
system RAM at the 4G mark. On this system, that was the first
address using 1G pages for the virt->phys direct mapping so the
PUD is pointing to a physical address, not a PMD page.
The problem is that the page table walker in kern_addr_valid() is
not checking pud_large() and treats the physical address as if
it was a PMD. If it happens to look like pmd_none then it'll
silently fail, probably returning zeros instead of real data. If
the data happens to look like a present PMD though, it will be
walked resulting in the oops above.
This patch adds the necessary pud_large() check.
Unfortunately the problem was not readily reproducible and now
they are running the backup program without accessing
/proc/kcore so the patch has not been validated but I think it
makes sense.
Signed-off-by: Mel Gorman <mgorman@suse.de> Reviewed-by: Rik van Riel <riel@redhat.coM> Reviewed-by: Michal Hocko <mhocko@suse.cz> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: stable@vger.kernel.org Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20130211145236.GX21389@suse.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Wed, 13 Feb 2013 00:20:07 +0000 (16:20 -0800)]
Merge branch 'autofs-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux into akpm
Pull hp parisc automounter fix from Helge Deller:
"This unbreaks automounter support for the parisc architecture (and
probably aarch64 as well).""
* 'autofs-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
unbreak automounter support on 64-bit kernel with 32-bit userspace (v2)
Linus Torvalds [Wed, 13 Feb 2013 00:16:29 +0000 (16:16 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux into akpm
Pull s390 regression fix from Martin Schwidefsky:
"The recent fix for the s390 sched_clock() function uncovered yet
another bug in s390_next_ktime which causes an endless loop in KVM.
This regression should be fixed before v3.8.
I keep the fingers crossed that this is the last one for v3.8."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/timer: avoid overflow when programming clock comparator
Linus Torvalds [Tue, 12 Feb 2013 23:13:42 +0000 (15:13 -0800)]
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile into akpm
Pull tile bugfixes from Chris Metcalf:
"This includes a variety of minor bug fixes, mostly to do with testing
"make allyesconfig", "make allmodconfig", "make allnoconfig", inspired
to Tejun Heo's observation about Kconfig.freezer not being included.
The largest changes are just syntax changes removing the tile-specific
use of a macro named INT_MASK, which is way too commonly redefined
throughout driver code"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: tag some code with #ifdef CONFIG_COMPAT
tile: fix memcpy_*io functions for allnoconfig
tile: export a handful of symbols appropriately
drm: fix compile failure by including <linux/swiotlb.h>
tile: avoid defining INT_MASK macro in <arch/interrupts.h>
tile: provide "screen_info" when enabling VT
drivers/input/joystick/analog.c: enable precise timer
tile: include kernel/Kconfig.freezer in tile Kconfig
tile: remove an unused variable in copy_thread()
Linus Torvalds [Tue, 12 Feb 2013 23:12:24 +0000 (15:12 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into akpm
Pull ARM SoC fixes from Olof Johansson:
"We had a number of fixes queued up, but taking a strict pass-through
and weeding out any that either have been broken for a while, or are
for platforms that need out-of-tree code to be useful anyway, or other
fixes for problems that few users are likely to see in real life, only
this short branch of patches remains.
The three patches here are to make SMP boot work on the Calxeda
platforms again. Some of the rework for cpuids on 3.8 broke it (and
it was discovered late, unfortunately)."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: highbank: mask cluster id from cpu_logical_map
ARM: scu: mask cluster id from cpu_logical_map
ARM: scu: add empty scu_enable for !CONFIG_SMP
Marek Szyprowski [Tue, 12 Feb 2013 21:46:24 +0000 (13:46 -0800)]
mm: cma: fix accounting of CMA pages placed in high memory
The total number of low memory pages is determined as totalram_pages -
totalhigh_pages, so without this patch all CMA pageblocks placed in
highmem were accounted to low memory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minchan Kim <minchan.kim@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Glauber Costa [Tue, 12 Feb 2013 21:46:22 +0000 (13:46 -0800)]
memcg: fix kmemcg registration for late caches
The designed workflow for the caches in kmemcg is: register it with
memcg_register_cache() if kmemcg is already available or later on when a
new kmemcg appears at memcg_update_cache_sizes() which will handle all
caches in the system. The caches created at boot time will be handled
by the later, and the memcg-caches as well as any system caches that are
registered later on by the former.
There is a bug, however, in memcg_register_cache: we correctly set up
the array size, but do not mark the cache as a root cache.
This means that allocations for any cache appearing late in the game
will see memcg->memcg_params->is_root_cache == false, and in particular,
trigger VM_BUG_ON(!cachep->memcg_params->is_root_cache) in
__memcg_kmem_cache_get.
The obvious fix is to include the missing assignment.
Signed-off-by: Glauber Costa <glommer@parallels.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gerald Schaefer [Tue, 12 Feb 2013 21:46:20 +0000 (13:46 -0800)]
mm: don't overwrite mm->def_flags in do_mlockall()
With commit 8e72033f2a48 ("thp: make MADV_HUGEPAGE check for
mm->def_flags") the VM_NOHUGEPAGE flag may be set on s390 in
mm->def_flags for certain processes, to prevent future thp mappings.
This would be overwritten by do_mlockall(), which sets it back to 0 with
an optional VM_LOCKED flag set.
To fix this, instead of overwriting mm->def_flags in do_mlockall(), only
the VM_LOCKED flag should be set or cleared.
Linus Walleij [Tue, 12 Feb 2013 21:46:19 +0000 (13:46 -0800)]
drivers/rtc/rtc-pl031.c: restore ST variant functionality
Commit e7e034e18a0a ("drivers/rtc/rtc-pl031.c: fix the missing operation
on enable") accidentally broke the ST variants of PL031.
The bit that is being poked as "clockwatch" enable bit for the ST
variants does the work of bit 0 on this variant. Bit 0 is used for a
clock divider on the ST variants, and setting it to 1 will affect
timekeeping in a very bad way.
David S. Miller [Tue, 12 Feb 2013 21:11:09 +0000 (16:11 -0500)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Here is another handful of late-breaking fixes intended for the 3.8
stream... Hopefully the will still make it! :-)
There are three mac80211 fixes pulled from Johannes:
"Here are three fixes still for the 3.8 stream, the fix from Cong Ding
for the bad sizeof (Stephen Hemminger had pointed it out before but I'd
promptly forgotten), a mac80211 managed-mode channel context usage fix
where a downgrade would never stop until reaching non-HT and a bug in
the channel determination that could cause invalid channels like HT40+
on channel 11 to be used."
Also included is a mwl8k fix that avoids an oops when using mwl8k
devices that only support the 5 GHz band.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Tue, 12 Feb 2013 09:45:44 +0000 (09:45 +0000)]
ixgbe: Only set gso_type to SKB_GSO_TCPV4 as RSC does not support IPv6
The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct. RSC is only supported with IPv4/TCP frames only. As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.
The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Tommi Rantala <tt.rantala@gmail.com> Tested-by: Tommi Rantala <tt.rantala@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Pavel Emelyanov <xemul@parallels.com> Acked-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 12 Feb 2013 16:17:35 +0000 (08:17 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Three nouveau fixes, all user visible issues, and one radeon
regression fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: enforce use of radeon_get_ib_value when reading user cmd
drm/nouveau: add lockdep annotations
drm/nv50/fb: Fix nullptr-deref on IGPs
drm/nouveau: use different register to wait for secret scrubber
Jerome Glisse [Mon, 11 Feb 2013 13:57:18 +0000 (08:57 -0500)]
drm/radeon: enforce use of radeon_get_ib_value when reading user cmd
When ever parsing cmd buffer supplied by userspace we need to use
radeon_get_ib_value rather than directly accessing the ib as the user
cmd might not yet be copied into the ib thus the parser might read
value that does not correspond to what user is sending and possibly
allowing user to send malicious command undected.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jonas Gorski [Fri, 8 Feb 2013 15:07:25 +0000 (16:07 +0100)]
mwl8k: fix band for supported channels
The band field for the supported channels were left unpopulated, making
them default to 0 == IEEE80211_BAND_2GHZ, even for the 5GHz channels.
This resulted in null pointer accesses if anything tries to access
wiphy->bands[channel->band] of a 5GHz channel on 5GHz only cards, since
wiphy->bands[2GHZ] is NULL for them (e.g. cfg80211_chandef_usable does).
Spanning Tree Protocol packets should have always been marked as
control packets, this causes them to get queued in the high prirority
FIFO. As Radia Perlman mentioned in her LCA talk, STP dies if bridge
gets overloaded and can't communicate. This is a long-standing bug back
to the first versions of Linux bridge.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stoney Wang [Thu, 7 Feb 2013 18:53:02 +0000 (10:53 -0800)]
x86/apic: Work around boot failure on HP ProLiant DL980 G7 Server systems
When a HP ProLiant DL980 G7 Server boots a regular kernel,
there will be intermittent lost interrupts which could
result in a hang or (in extreme cases) data loss.
The reason is that this system only supports x2apic physical
mode, while the kernel boots with a logical-cluster default
setting.
This bug can be worked around by specifying the "x2apic_phys" or
"nox2apic" boot option, but we want to handle this system
without requiring manual workarounds.
The BIOS sets ACPI_FADT_APIC_PHYSICAL in FADT table.
As all apicids are smaller than 255, BIOS need to pass the
control to the OS with xapic mode, according to x2apic-spec,
chapter 2.9.
Current code handle x2apic when BIOS pass with xapic mode
enabled:
When user specifies x2apic_phys, or FADT indicates PHYSICAL:
1. During madt oem check, apic driver is set with xapic logical
or xapic phys driver at first.
2. enable_IR_x2apic() will enable x2apic_mode.
3. if user specifies x2apic_phys on the boot line, x2apic_phys_probe()
will install the correct x2apic phys driver and use x2apic phys mode.
Otherwise it will skip the driver will let x2apic_cluster_probe to
take over to install x2apic cluster driver (wrong one) even though FADT
indicates PHYSICAL, because x2apic_phys_probe does not check
FADT PHYSICAL.
Add checking x2apic_fadt_phys in x2apic_phys_probe() to fix the
problem.
Johannes Berg [Sat, 9 Feb 2013 20:46:34 +0000 (21:46 +0100)]
mac80211: fix channel selection bug
When trying to connect to an AP that advertises HT but not
VHT, the mac80211 code erroneously uses the configuration
from the AP as is instead of checking it against regulatory
and local capabilities. This can lead to using an invalid
or even inexistent channel (like 11/HT40+).
Additionally, the return flags from downgrading must be
ORed together, to collect them from all of the downgrades.
Also clarify the message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Mon, 11 Feb 2013 01:44:08 +0000 (20:44 -0500)]
Merge branch 'master' of git://1984.lsi.us.es/nf
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter/IPVS fixes for 3.8-rc7, they are:
* Fix oops in IPVS state-sync due to releasing a random memory area due
to unitialized pointer, from Dan Carpenter.
* Fix SCTP flow establishment due to bad checksumming mangling in IPVS,
from Daniel Borkmann.
* Three fixes for the recently added IPv6 NPT, all from YOSHIFUJI Hideaki,
with an amendment collapsed into those patches from Ulrich Weber. They
fiix adjustment calculation, fix prefix mangling and ensure LSB of
prefixes are zeroes (as required by RFC).
Specifically, it took me a while to validate the 1's complement arithmetics/
checksumming approach in the IPv6 NPT code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>