staging/rdma/hfi1: Fix QSFP memory read/write across 128 byte boundary
The QSFP memory cache reads both lower and upper page 0H in one shot,
which leads to the address counter wrapping around to the beginning of
lower page 00H at byte 128, as defined by SFF-8636.
This patch fixes this by modifying the underlying QSFP read and writes
to avoid this wrap around.
Reviewed-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Bryan Morgan [Wed, 3 Feb 2016 22:30:49 +0000 (14:30 -0800)]
staging/rdma/hfi1: HFI reports wrong offline disabled reason when cable removed
Removing QSFP cable should report 'No Local Media' instead of
'Transient' as reported by 'opaportinfo'.
Workaround is to change the state to
OPA_LINKDOWN_REASON_LOCAL_MEDIA_NOT_INSTALLED in cable handler.
With cable still removed, 'opaportinfo bounce' should not cause a
state change to Polling, as reported by 'opaportinfo'.
Resolution is to prevent physical state change from Offline->Polling.
Use a macro to mask lower nibble of OPA_LINKDOWN_REASON* as needed
for offline_disabled_reason.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com> Reviewed-by: Dean Luick <dean.luick@intel.com> Reported-by: Todd Rimmer <todd.rimmer@intel.com> Signed-off-by: Bryan Morgan <bryan.c.morgan@intel.com> Signed-off-by: Jubin John <jubin.john@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
staging/rdma/hfi1: Remove modify queue pair from hfi1
In addition to removing the modify queue pair verb from hfi1 we also
remove ancillary functions which existed only for modify queue pair and
are also already present in hfi1.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
staging/rdma/hfi1: Use rdmavt version of post_send
This patch removes the post_send and post_one_send from the hfi1 driver.
The "posting" of sends will be done by rdmavt which will walk a WQE and
queue work. This patch will still provide the capability to schedule that
work as well as kick the progress. These are provided to the rdmavt layer.
Reviewed-by: Jubin John <jubin.john@intel.com> Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Edward Mascarenhas <edward.mascarenhas@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
staging/rdma/hfi1: Remove CQ data structures and functions from hfi1
The completion queue is not a complex data structure and it can be removed
at the same time as its functions. Unlike the more complicated queue pair
which was done in multiple patches. This single patch removes all traces
of hfi1 specific completeion queues from the hfi1 driver.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
staging/rdma/hfi1: Remove qpdev and qpn table from hfi1
Another change on the way to removing queue pair functionality from
hfi1. This patch removes the private queue pair structure and the table
which holds the queue pair numbers in favor of using what is provided
by rdmavt.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
No need to keep providing the query pkey function. This is now being
done in rdmavt. Remove support from hfi1. The allocation and
maintenance of the list still resides in the driver.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Mmap data structure has already been moved to rdmavt and hfi1 supports
it. Now that the mmap functionality has also been moved to rdmavt its
time for hfi1 to use that as well.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
staging/rdma/hfi1: Remove driver specific members from hfi1 qp type
In preparation for moving the queue pair data structure to rdmavt the
members of the driver specific queue pairs which are not common need to be
pushed off to a private driver structure. This structure will be available
in the queue pair once moved to rdmavt as a void pointer. This patch while
not adding a lot of value in and of itself is a prerequisite to move the
queue pair out of the drivers and into rdmavt.
The driver specific, private queue pair data structure should condense as
more of the send side code moves to rdmavt.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch begins to make use of rdmavt by registering with it and
providing access to the header files. This is just the beginning of
rdmavt support in hfi1.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Harish Chegondi [Wed, 3 Feb 2016 22:20:52 +0000 (14:20 -0800)]
IB/qib: Remove modify_port and port_immutable functions
Delete code from query_port which has been moved into rvt_query_port
Create a call back function to shut down a port which may be called from
rvt_modify_port
Query gid is in rdmavt, but still relies on the driver to maintain the
guid table. Add the necessary driver call back and remove the existing
verb handler.
Harish Chegondi [Wed, 3 Feb 2016 22:20:19 +0000 (14:20 -0800)]
IB/qib: Remove qib_lookup_qpn and use rvt_lookup_qpn instead
Add calls to rcu_read_lock()/rcu_read_unlock() as rvt_lookup_qpn callers
must hold the rcu_read_lock before calling and keep the lock until the
returned qp is no longer in use.
Remove lookaside qp and some qp refcount atomics in the sdma send code
that is redundant with the s_dma_busy refcount, which will also stall
the state processing to the reset state.
Change the qpn hash function to hash_32 which is hash function used
in rvt_lookup_qpn. qpn_hash function would be eliminated in later patches.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Harish Chegondi [Wed, 3 Feb 2016 22:15:20 +0000 (14:15 -0800)]
IB/rdmavt: Add support for query_port, modify_port and get_port_immutable
rvt_query_port calls into the driver through a call back function
query_port_state to populate the rest of ib_port_attr elements.
rvt_modify_port calls into the driver if needed through a call back
function shut_down_port()
Addin query gid support. Rdmavt still relies on the driver to maintain
the gid table. Rdmavt simply calls into the driver to retrive the guid
for a particular port.
IB/rdmavt: Clean up distinction between port number and index
IB core uses 1 relative indexing for ports. All of our data structures
use 0 based indexing. Add an inline function that we can use whenever we
need to validate a legal value and try to convert a port number to a
port index at the entrance into rdmavt.
Try to follow the policy that when we are talking about a port from IB
core point of view we refer to it as a port number. When port is an
index into our arrays refer to it as a port index.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Harish Chegondi [Fri, 22 Jan 2016 21:07:42 +0000 (13:07 -0800)]
IB/qib: Use rdmavt version of post_send
This patch removes the post_send and post_one_send from the qib driver.
The "posting" of sends will be done by rdmavt which will walk a WQE and
queue work. This patch will still provide the capability to schedule that
work as well as kick the progress. These are provided to the rdmavt layer.
This patch adds rdmavt device structure allocation in rdamvt. The
ib_device alloc is now done in rdmavt instead of the driver. Drivers
need to tell rdmavt the number of ports when calling.
A side of effect of this patch is fixing a bug with port initialization
where the device structure port array was allocated over top of an
existing one.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Ira Weiny [Fri, 22 Jan 2016 21:04:38 +0000 (13:04 -0800)]
IB/rdmavt: add modify queue pair driver helpers
Low level drivers need to be able to check incoming attributes as well as be
able to adjust their private data on queue pair modification. Add 2 driver
callbacks, check_modify_qp and modify_qp, to facilitate this.
Signed-off-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
There are a number of minor things that should be set by rdmavt rather
than by the drivers. Now that rdmavt has solidified in its design we can
go ahead and clean up this stuff.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds the simple post receive verbs call to rdmavt. The actual
interrupt handling and packet processing is still done in the low level
driver.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds support of tracing events using the kernels built-in event
tracing infrastructure. This can be extended to provide a wide range of
trace and debug capabilities which have a negligible impact on performance
when enabled. These should be preferred over the use of the rvt_pr*
functions.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Add in a post_send and post_one_send to rdmavt. The ULP will provide a WQE
to rdmavt which will then walk and queue each element. Rdmavt will then
queue the work to be done in the driver or kick the driver's progress
routine.
There needs to be a follow on patch which adds in another lock for the
head of the queue so that it can be added to and read from in parallel.
This will touch protocol handlers and require other changes in the
drivers. This will be done separately.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Harish Chegondi [Fri, 22 Jan 2016 20:56:52 +0000 (12:56 -0800)]
IB/qib: Remove create qp and create qp table functionality
Rely on rdmavt functions for creation of qp and qp table. Function to
allocate a qpn is still being provided by qib as the algorithm to allocate
a qpn in qib is different from that of the algorithm in rdmavt.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Harish Chegondi [Fri, 22 Jan 2016 20:56:21 +0000 (12:56 -0800)]
IB/qib: Use rdmavt pkey verbs function
Remove qib query pkey function which is no longer needed as this is now
being done in rdmavt. The allocation and maintenance of the list still
resides in the driver.
Harish Chegondi [Fri, 22 Jan 2016 20:56:02 +0000 (12:56 -0800)]
IB/qib: Remove ibport and use rdmavt version
Remove several ibport members from qib and use the rdmavt version. rc_acks,
rc_qacks, and rc_delayed_comp are defined as per CPU variables in rdmavt.
Add support for these rdmavt per CPU variables which were not per cpu
variables in qib ibport structure.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Mike Marciniszyn [Fri, 22 Jan 2016 20:50:43 +0000 (12:50 -0800)]
IB/rdmavt: Support creating qps with GFP_NOIO flag
The current code is problematic when the QP creation and ipoib is
used to support NFS and NFS desires to do IO for paging purposes.
In that case, the GFP_KERNEL allocation within create_qp causes
a deadlock in tight memory situations.
This fix adds support to create queue pair with GFP_NOIO flag for
connected mode only to cleanly fail the create queue pair in those
situations.
This was previously fixed in qib but needed to get ported to hfi1.
This patch handles that for both hardwares in the new rdmavt common
layer.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Harish Chegondi [Fri, 22 Jan 2016 20:50:36 +0000 (12:50 -0800)]
IB/rdmavt: Add support for rvt_query_device function
With this commit, the drivers using rdmavt need not define query_device
function. But they should fill in the IB device attributes structure
rvt_dev_info.dparms.props
Until all queue pair functionality is moved to rdmavt we need to provide
access to the reset function. This is only temporary and will be reverted
back to a static, non exported function in the end.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Harish Chegondi <harish.chegondi@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Harish Chegondi [Fri, 22 Jan 2016 20:50:05 +0000 (12:50 -0800)]
IB/rdmavt: Add IB user context allocation and de-alloction functions
Adding IB user context alloc and dealloc functions to rdmavt so that the
drivers that use rdmavt can use these functions instead of defining their
own functions.
Remove qp and mr support from qib and use rdmavt. These two changes
cannot be reasonably be split apart into separate patches because they
depend on each other in mulitple places. This paves the way to remove
even more functions in subsequent patches.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/qib: Remove driver specific members from qib qp type
In preparation for moving the queue pair data structure to rdmavt the
members of the driver specific queue pairs which are not common need to be
pushed off to a private driver structure. This structure will be available
in the queue pair once moved to rdmavt as a void pointer. This patch while
not adding a lot of value in and of itself is a prerequisite to move the
queue pair out of the drivers and into rdmavt.
The driver specific, private queue pair data structure should condense as
more of the send side code moves to rdmavt.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Original patch for AH changes from Kamal Heib <kamalh@mellanox.com>, split
apart from original. This patch also removes the qib specific multicast
lid base and permissive lid defines since they are no longer needed.
Use common LID defines in qib driver.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Kamal Heib <kamalh@mellanox.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/qib: Remove most uses of QIB_PERMISSIVE_LID and QIB_MULTICAST_LID_BASE
This patch removes most of the uses of QIB_PERMISSIBVE_LID and
QIB_MULTICAST_LID_BASE in favor of the recently added IB_* versions.
There are still minor uses in AH functions as well as the QIB_* defines
but those will be removed in a follow on patch.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch begins to make use of rdmavt by registering with it and
providing access to the header files. This is just the beginning of
rdmavt support in qib.
Most functionality is still being done in the driver, set flags so that
rdmavt will let qib continue to handle mr, qp, and cq init.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Add pkey table in rdi per port data structure. Also bring in related pkey
functions. Drivers will still be responsible for allocating and
maintaining the pkey table. However they need to tell rdmavt where to find
the pkey table. We can not move the pkey table up into rdmavt because
drivers need to manipulate this long before registering with it.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/rdmavt: Break rdma_vt main include header file up
Until all functionality is moved over to rdmavt drivers still need to
access a number of fields in data structures that are predominantly
meant to be used by rdmavt. Once these rdmavt_<ibta_object>.h header
files are no longer being touched by drivers their content should be
moved to rdmavt/<ibta_object>.h. While here move a couple #defines
over to more general IB verbs header files because they fit better.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
projects / linux-beck.git / log