Paul Gortmaker [Sun, 31 Jul 2011 21:36:35 +0000 (21:36 +0000)]
sh: Fix conflicting definitions of ptrace_triggered
The extra nmi argument is causing this compile fail:
CC arch/sh/kernel/ptrace_32.o
arch/sh/kernel/ptrace_32.c:66:6: error: conflicting types for 'ptrace_triggered'
arch/sh/include/asm/ptrace.h:126:13: note: previous declaration of 'ptrace_triggered' was here
make[3]: *** [arch/sh/kernel/ptrace_32.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 2 Aug 2011 09:42:54 +0000 (09:42 +0000)]
serial: sh-sci: fix DMA build by including dma-mapping.h
Include dma-mapping.h to fix build of the sh-sci driver on
SH-Mobile ARM (sh73a0) when CONFIG_SERIAL_SH_SCI_DMA=y:
drivers/tty/serial/sh-sci.c: In function 'sci_rx_dma_release':
drivers/tty/serial/sh-sci.c:1182:3: error: implicit declaration of function 'dma_free_coherent'
drivers/tty/serial/sh-sci.c: In function 'work_fn_tx':
drivers/tty/serial/sh-sci.c:1333:2: error: implicit declaration of function 'dma_sync_sg_for_device'
drivers/tty/serial/sh-sci.c: In function 'sci_request_dma':
drivers/tty/serial/sh-sci.c:1498:3: error: implicit declaration of function 'dma_map_sg'
drivers/tty/serial/sh-sci.c:1527:3: error: implicit declaration of function 'dma_alloc_coherent'
drivers/tty/serial/sh-sci.c:1527:10: warning: assignment makes pointer from integer without a cast
make[3]: *** [drivers/tty/serial/sh-sci.o] Error 1
make[2]: *** [drivers/tty/serial] Error 2
make[1]: *** [drivers/tty] Error 2
make: *** [drivers] Error 2
Signed-off-by: Magnus Damm <damm@opensource.se> Tested-by: Simon Horman <horms@verge.net.au> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Wed, 3 Aug 2011 03:33:20 +0000 (12:33 +0900)]
serial: sh-sci: Fix up default regtype probing.
Presently the default regtype probing inadvertently bails out due to an
inverted error check. This fixes it up, and gets platforms without
explicit regtype specifications working again.
Reported-by: Magnus Damm <damm@opensource.se> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
oom: task->mm == NULL doesn't mean the memory was freed
exit_mm() sets ->mm == NULL then it does mmput()->exit_mmap() which
frees the memory.
However select_bad_process() checks ->mm != NULL before TIF_MEMDIE,
so it continues to kill other tasks even if we have the oom-killed
task freeing its memory.
Change select_bad_process() to check ->mm after TIF_MEMDIE, but skip
the tasks which have already passed exit_notify() to ensure a zombie
with TIF_MEMDIE set can't block oom-killer. Alternatively we could
probably clear TIF_MEMDIE after exit_mmap().
Linus Torvalds [Tue, 2 Aug 2011 00:05:46 +0000 (14:05 -1000)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (23 commits)
regulator: Improve WM831x DVS VSEL selection algorithm
regulator: Bootstrap wm831x DVS VSEL value from ON VSEL if not already set
regulator: Set up GPIO for WM831x VSEL before enabling VSEL mode
regulator: Add EPEs to the MODULE_ALIAS() for wm831x-dcdc
regulator: Fix WM831x DCDC DVS VSEL bootstrapping
regulator: Fix WM831x regulator ID lookups for multiple WM831xs
regulator: Fix argument format type errors in error prints
regulator: Fix memory leak in set_machine_constraints() error paths
regulator: Make core more chatty about some errors
regulator: tps65910: Fix array access out of bounds bug
regulator: tps65910: Add missing breaks in switch/case
regulator: tps65910: Fix a memory leak in tps65910_probe error path
regulator: TWL: Remove entry of RES_ID for 6030 macros
ASoC: tlv320aic3x: Add correct hw registers to Line1 cross connect muxes
regulator: Add basic per consumer debugfs
regulator: Add rdev_crit() macro
regulator: Refactor supply implementation to work as regular consumers
regulator: Include the device name in the microamps_requested_ file
regulator: Increase the limit on sysfs file names
regulator: Properly register dummy regulator driver
...
Linus Torvalds [Mon, 1 Aug 2011 23:56:03 +0000 (13:56 -1000)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (60 commits)
ext4: prevent memory leaks from ext4_mb_init_backend() on error path
ext4: use EXT4_BAD_INO for buddy cache to avoid colliding with valid inode #
ext4: use ext4_msg() instead of printk in mballoc
ext4: use ext4_kvzalloc()/ext4_kvmalloc() for s_group_desc and s_group_info
ext4: introduce ext4_kvmalloc(), ext4_kzalloc(), and ext4_kvfree()
ext4: use the correct error exit path in ext4_init_inode_table()
ext4: add missing kfree() on error return path in add_new_gdb()
ext4: change umode_t in tracepoint headers to be an explicit __u16
ext4: fix races in ext4_sync_parent()
ext4: Fix overflow caused by missing cast in ext4_fallocate()
ext4: add action of moving index in ext4_ext_rm_idx for Punch Hole
ext4: simplify parameters of reserve_backup_gdb()
ext4: simplify parameters of add_new_gdb()
ext4: remove lock_buffer in bclean() and setup_new_group_blocks()
ext4: simplify journal handling in setup_new_group_blocks()
ext4: let setup_new_group_blocks() set multiple bits at a time
ext4: fix a typo in ext4_group_extend()
ext4: let ext4_group_add_blocks() handle 0 blocks quickly
ext4: let ext4_group_add_blocks() return an error code
ext4: rename ext4_add_groupblocks() to ext4_group_add_blocks()
...
Fix up conflict in fs/ext4/inode.c: commit aacfc19c626e ("fs: simplify
the blockdev_direct_IO prototype") had changed the ext4_ind_direct_IO()
function for the new simplified calling convention, while commit dae1e52cb126 ("ext4: move ext4_ind_* functions from inode.c to
indirect.c") moved the function to another file.
Linus Torvalds [Mon, 1 Aug 2011 23:48:31 +0000 (13:48 -1000)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
xfs: Fix build breakage in xfs_iops.c when CONFIG_FS_POSIX_ACL is not set
VFS: Reorganise shrink_dcache_for_umount_subtree() after demise of dcache_lock
VFS: Remove dentry->d_lock locking from shrink_dcache_for_umount_subtree()
VFS: Remove detached-dentry counter from shrink_dcache_for_umount_subtree()
switch posix_acl_chmod() to umode_t
switch posix_acl_from_mode() to umode_t
switch posix_acl_equiv_mode() to umode_t *
switch posix_acl_create() to umode_t *
block: initialise bd_super in bdget()
vfs: avoid call to inode_lru_list_del() if possible
vfs: avoid taking inode_hash_lock on pipes and sockets
vfs: conditionally call inode_wb_list_del()
VFS: Fix automount for negative autofs dentries
Btrfs: load the key from the dir item in readdir into a fake dentry
devtmpfs: missing initialialization in never-hit case
hppfs: missing include
Linus Torvalds [Mon, 1 Aug 2011 23:40:51 +0000 (13:40 -1000)]
Merge branch 'pstore-efi' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'pstore-efi' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
efivars: Introduce PSTORE_EFI_ATTRIBUTES
efivars: Use string functions in pstore_write
efivars: introduce utf16_strncmp
efivars: String functions
efi: Add support for using efivars as a pstore backend
pstore: Allow the user to explicitly choose a backend
pstore: Make "part" unsigned
pstore: Add extra context for writes and erases
pstore: Extend API for more flexibility in new backends
Linus Torvalds [Mon, 1 Aug 2011 23:39:40 +0000 (13:39 -1000)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kdb,kgdb: Allow arbitrary kgdb magic knock sequences
kdb: Remove all references to DOING_KGDB2
kdb,kgdb: Implement switch and pass buffer from kdb -> gdb
kdb: cleanup unused variables missed in the original kdb merge
Yu Jian [Mon, 1 Aug 2011 21:41:46 +0000 (17:41 -0400)]
ext4: prevent memory leaks from ext4_mb_init_backend() on error path
In ext4_mb_init(), if the s_locality_group allocation fails it will
currently cause the allocations made in ext4_mb_init_backend() to
be leaked. Moving the ext4_mb_init_backend() allocation after the
s_locality_group allocation avoids that problem.
The first packet that gdb sends when the kernel is in kdb mode seems
to change with every release of gdb. Instead of continuing to add
many different gdb packets, change kdb to automatically look for any
thing that looks like a gdb packet.
Example 1 cold start test:
echo g > /proc/sysrq-trigger
$D#44+
Example 2 cold start test:
echo g > /proc/sysrq-trigger
$3#33
The second one should re-enter kdb's shell right away and is purely a
test.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Jason Wessel [Mon, 23 May 2011 18:22:54 +0000 (13:22 -0500)]
kdb: Remove all references to DOING_KGDB2
The DOING_KGDB2 was originally a state variable for one of the two
ways to automatically transition from kdb to kgdb. Purge all these
variables and just use one single state for the transition.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Jason Wessel [Mon, 23 May 2011 18:17:41 +0000 (13:17 -0500)]
kdb,kgdb: Implement switch and pass buffer from kdb -> gdb
When switching from kdb mode to kgdb mode packets were getting lost
depending on the size of the fifo queue of the serial chip. When gdb
initially connects if it is in kdb mode it should entirely send any
character buffer over to the gdbstub when switching connections.
Previously kdb was zero'ing out the character buffer and this could
lead to gdb failing to connect at all, or a lengthy pause could occur
on the initial connect.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
CIFS: Cleanup demupltiplex thread exiting code
CIFS: Move mid search to a separate function
CIFS: Move RFC1002 check to a separate function
CIFS: Simplify socket reading in demultiplex thread
CIFS: Move buffer allocation to a separate function
cifs: remove unneeded variable initialization in cifs_reconnect_tcon
cifs: simplify refcounting for oplock breaks
cifs: fix compiler warning in CIFSSMBQAllEAs
cifs: fix name parsing in CIFSSMBQAllEAs
cifs: don't start signing too early
cifs: trivial: goto out here is unnecessary
cifs: advertise the right receive buffer size to the server
Pavel Shilovsky [Mon, 1 Aug 2011 09:19:44 +0000 (13:19 +0400)]
CIFS: Cleanup demupltiplex thread exiting code
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Pavel Shilovsky [Mon, 1 Aug 2011 09:19:43 +0000 (13:19 +0400)]
CIFS: Move mid search to a separate function
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Pavel Shilovsky [Mon, 1 Aug 2011 09:19:42 +0000 (13:19 +0400)]
CIFS: Move RFC1002 check to a separate function
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Pavel Shilovsky [Mon, 1 Aug 2011 09:19:41 +0000 (13:19 +0400)]
CIFS: Simplify socket reading in demultiplex thread
Move reading to separate function and remove csocket variable.
Also change semantic in a little: goto incomplete_rcv only when
we get -EAGAIN (or a familiar error) while reading rfc1002 header.
In this case we don't check for echo timeout when we don't get whole
header at once, as it was before.
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Theodore Ts'o [Mon, 1 Aug 2011 12:45:02 +0000 (08:45 -0400)]
ext4: introduce ext4_kvmalloc(), ext4_kzalloc(), and ext4_kvfree()
Introduce new helper functions which try kmalloc, and then fall back
to vmalloc if necessary, and use them for allocating and deallocating
s_flex_groups.
Pavel Shilovsky [Mon, 1 Aug 2011 09:19:40 +0000 (13:19 +0400)]
CIFS: Move buffer allocation to a separate function
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
David Brown [Mon, 16 May 2011 22:53:38 +0000 (15:53 -0700)]
gpio_msm: Move Qualcomm MSM v2 gpio driver into drivers
Migrate the driver for the v7-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55 Signed-off-by: David Brown <davidb@codeaurora.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
David Brown [Mon, 16 May 2011 20:57:39 +0000 (13:57 -0700)]
gpio_msm: Move Qualcomm v6 MSM driver into drivers
Migrate the driver for the v6-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9 Signed-off-by: David Brown <davidb@codeaurora.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
David Brown [Mon, 16 May 2011 20:32:15 +0000 (13:32 -0700)]
msm: gpiomux: Move public API to public header
The gpiomux.h header contains some SOC ifdefs. However, the API that
is actually used by the GPIO driver only uses two functions that are
general. Move these general definitions into a public header file.
Change-Id: Ia5df8af87dba268225598d56908e523bcfc24ef6 Signed-off-by: David Brown <davidb@codeaurora.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
David Brown [Thu, 12 May 2011 08:28:01 +0000 (01:28 -0700)]
msm: gpio: Remove ifdefs on gpio chip registers
Select the GPIO register configuration at runtime rather than through
idefs.
Change-Id: I02ea0a3d61bc81669f32097c32420f0688552231 Signed-off-by: David Brown <davidb@codeaurora.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Put an SOC prefix on each GPIO register definition, eliminating the
need to have SOC ifdefs around the definitions.
Change-Id: I5a01fd328a89ce1be610847934d6e118f5465e42 Signed-off-by: David Brown <davidb@codeaurora.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
David Brown [Thu, 12 May 2011 07:54:36 +0000 (00:54 -0700)]
msm: Remove chip-ifdefs for GPIO io mappings
The two GPIO controllers are always mapped to the same virtual address
across all MSM devices. Instead of selecting this at compile time,
determine the physical address at runtime, eliminating yet something
else preventing multiple MSM targets from being compiled into the same
kernel.
Change-Id: I1672219d978ab6243526adeda6badf49472baa27 Signed-off-by: David Brown <davidb@codeaurora.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
David Brown [Thu, 12 May 2011 07:33:38 +0000 (00:33 -0700)]
msm: gpio: Remove unsupported devices
The MSM7x25 and MSM7x27 devices are not yet supported in the kernel.
Remove #ifdef-based tables supporting these chips for now.
Change-Id: I4d9f5abc4cc0942ce75a067097b072489493c1b8 Signed-off-by: David Brown <davidb@codeaurora.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tomi Valkeinen [Mon, 1 Aug 2011 11:32:23 +0000 (14:32 +0300)]
HACK: OMAP: DSS2: clk hack for OMAP2/3
The HWMOD data for OMAP2 and 3 are currently not up to date regarding
DSS (OMAP4 HWMOD data is fine). This patch makes the DSS driver to get
the opt clocks needed for OMAP2/3 with the old clock names, thus
allowing DSS driver to use runtime PM.
The HWMOD databases should be fixes ASAP, and this patch can be reverted
after that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Yongqiang Yang [Mon, 1 Aug 2011 10:32:19 +0000 (06:32 -0400)]
ext4: use the correct error exit path in ext4_init_inode_table()
This patch lets ext4_init_inode_table() handle errors right.
ext4_init_inode_table() should down_write() alloc_sem which
has been up_write()ed and stop the started journal handle.
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
David Howells [Tue, 7 Jun 2011 13:09:30 +0000 (14:09 +0100)]
VFS: Reorganise shrink_dcache_for_umount_subtree() after demise of dcache_lock
Reorganise shrink_dcache_for_umount_subtree() in light of the demise of
dcache_lock. Without that dcache_lock, there is no need for the batching of
removal of dentries from the system under it (we wanted to make intensive use
of the locked data whilst we held it, but didn't want to hold it for long at a
time).
This works, provided the preceding patch is correct in its removal of locking
on dentry->d_lock on the basis that no one should be locking these dentries any
more as the whole superblock is defunct.
With this patch, the calls to dentry_lru_del() and __d_shrink() are placed at
the point where each dentry is detached handled.
It is possible that, as an alternative, the batching should still be done -
but only for dentry_lru_del() of all a dentry's children in one go. In such a
case, the batching would be done under dcache_lru_lock.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
as part of the RCU-based pathwalk changes, despite the fact that the caller
(shrink_dcache_for_umount()) notes in the banner comment the reasons that
d_lock is not necessary in these functions:
/*
* destroy the dentries attached to a superblock on unmounting
* - we don't need to use dentry->d_lock because:
* - the superblock is detached from all mountings and open files, so the
* dentry trees will not be rearranged by the VFS
* - s_umount is write-locked, so the memory pressure shrinker will ignore
* any dentries belonging to this superblock that it comes across
* - the filesystem itself is no longer permitted to rearrange the dentries
* in this superblock
*/
So remove these locks. If the locks are actually necessary, then this banner
comment should be altered instead.
The hash table chains are protected by 1-bit locks in the hash table heads, so
those shouldn't be a problem.
Note that to make this work, __d_drop() has to be split so that the RCUwalk
barrier can be avoided. This causes problems otherwise as it has an assertion
that dentry->d_lock is locked - but there is no need for that as no one else
can be trying to access this dentry, except to step over it (and that should
be handled by d_free(), I think).
Signed-off-by: David Howells <dhowells@redhat.com> Cc: Nick Piggin <npiggin@kernel.dk> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Howells [Tue, 7 Jun 2011 13:09:10 +0000 (14:09 +0100)]
VFS: Remove detached-dentry counter from shrink_dcache_for_umount_subtree()
Remove the detached-dentry counter from shrink_dcache_for_umount_subtree() as
the value it computes is no longer used as of commit 312d3ca856d369bb04d0443846b85b4cdde6fa8a which made the nr_dentry counters
summed per-CPU rather than global atomic.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Lachlan McIlroy [Thu, 30 Jun 2011 01:01:45 +0000 (11:01 +1000)]
block: initialise bd_super in bdget()
bd_super is currently reset to NULL in kill_block_super() so we rely on previous
users of the block_device object to initialise this value for the next user.
This quirk was exposed on RHEL5 when a third party filesystem did not always use
kill_block_super() and therefore bd_super wasn't being reset when a block_device
object was recycled within the cache. This may not be a problem upstream but
makes sense to be defensive.
Signed-off-by: Lachlan McIlroy <lmcilroy@redhat.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Howells [Mon, 11 Jul 2011 13:20:57 +0000 (14:20 +0100)]
VFS: Fix automount for negative autofs dentries
Autofs may set the DCACHE_NEED_AUTOMOUNT flag on negative dentries. These
need attention from the automounter daemon regardless of the LOOKUP_FOLLOW flag.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Ian Kent <raven@themaw.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Josef Bacik [Tue, 28 Jun 2011 20:18:59 +0000 (16:18 -0400)]
Btrfs: load the key from the dir item in readdir into a fake dentry
In btrfs we have 2 indexes for inodes. One is for readdir, it's in this nice
sequential order and works out brilliantly for readdir. However if you use ls,
it usually stat's each file it gets from readdir. This is where the second
index comes in, which is based on a hash of the name of the file. So then the
lookup has to lookup this index, and then lookup the inode. The index lookup is
going to be in random order (since its based on the name hash), which gives us
less than stellar performance. Since we know the inode location from the
readdir index, I create a dummy dentry and copy the location key into
dentry->d_fsdata. Then on lookup if we have d_fsdata we use that location to
lookup the inode, avoiding looking up the other directory index. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Mon, 1 Aug 2011 00:31:44 +0000 (14:31 -1000)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (46 commits)
mfd: Fix mismatch in twl4030 mutex lock-unlock
mfd: twl6030-pwm.c needs MODULE_LICENSE
mfd: Fix the omap-usb-host clock API usage on usbhs_disable()
mfd: Acknowledge WM8994 IRQs before reporting
mfd: Acknowlege all WM831x IRQs before we handle them
mfd: Avoid two assignments if failures happen in tps65910_i2c_probe
regulator: Storing tps65912 error codes in u8
mfd: Don't leak init_data in tps65910_i2c_probe
regulator: aat2870: Add AAT2870 regulator driver
backlight: Add AAT2870 backlight driver
mfd: Add AAT2870 mfd driver
mfd: Remove dead code from max8997-irq
mfd: Move TPS55910 Kconfig option
mfd: Fix missing stmpe kerneldoc
mfd: Fix off-by-one value range checking for tps65912_i2c_write
mfd: Add devices for WM831x clocking module
mfd: Remove comp{1,2}_threshold sysfs entries in tps65911_comparator_remove
mfd: Don't ask about the TPS65912 core driver in Kconfig
mfd: Fix off by one in WM831x IRQ code
mfd: Add tps65921 support from twl-core
...
Linus Torvalds [Mon, 1 Aug 2011 00:30:59 +0000 (14:30 -1000)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/math-emu: Remove unnecessary code
m68k/math-emu: Remove commented out old code
m68k: Kill warning in setup_arch() when compiling for Sun3
m68k/atari: Prefix GPIO_{IN,OUT} with CODEC_
sparc: iounmap() and *_free_coherent() - Use lookup_resource()
m68k/atari: Reserve some ST-RAM early on for device buffer use
m68k/amiga: Chip RAM - Use lookup_resource()
resources: Add lookup_resource()
sparc: _sparc_find_resource() should check for exact matches
m68k/amiga: Chip RAM - Offset resource end by CHIP_PHYSADDR
m68k/amiga: Chip RAM - Use resource_size() to fix off-by-one error
m68k/amiga: Chip RAM - Change chipavail to an atomic_t
m68k/amiga: Chip RAM - Always allocate from the start of memory
m68k/amiga: Chip RAM - Convert from printk() to pr_*()
m68k/amiga: Chip RAM - Use tabs for indentation
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: Hemanth V <hemanthv@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
mfd: Fix the omap-usb-host clock API usage on usbhs_disable()
usbhs_disable function was invoking clk_enable() instead of
clk_disable(), thus only increasing the clock usage counter and
preventing this particular clock from being ever turned off.
Because of this, the power domain of omap4 the USB Host subsystem
would never reach lower power states.This patch calls clk_disable()
in usbhs_disable function
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Wed, 20 Jul 2011 16:05:13 +0000 (17:05 +0100)]
mfd: Acknowlege all WM831x IRQs before we handle them
Ensure that we never have a window where we've handled an interrupt (and
therefore need to be notified of new events) but haven't yet told the
interrupt controller that this is the case (so any new events will be
discarded).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
mfd: Avoid two assignments if failures happen in tps65910_i2c_probe
In drivers/mfd/tps65910.c:tps65910_i2c_probe() there's potential for a
tiny optimization.
We assign to init_data->irq and init_data->irq_base long before we
need them, and there are two potential exits from the function before
they are needed.
Moving the assignments below these two potential exits means we
completely avoid doing them in these two (failure) cases.
Jin Park [Mon, 4 Jul 2011 08:43:42 +0000 (17:43 +0900)]
regulator: aat2870: Add AAT2870 regulator driver
Add regulator driver for AnalogicTech AAT2870.
Signed-off-by: Jin Park <jinyoungp@nvidia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We either hit one of the case's or the default in the switch statement
in get_i2c(), so the 'return ERR_PTR(-EINVAL);' at the end of the
function is just dead code - remove it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Having another TPS chip at the end of the Kconfig when all it's
relatives are grouped together in their own section seems totally
counter-intuitive. Move it, also in the Makefile.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Wed, 22 Jun 2011 13:53:58 +0000 (14:53 +0100)]
mfd: Don't ask about the TPS65912 core driver in Kconfig
The user has to select the I2C and SPI drivers individually and they select
the core driver for the device so there's no point in presenting the user
with an option for the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The GPIO IRQs aren't the first IRQs defined, we need to subtract the base
for the GPIOs as well to use them for array indexes.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Mon, 20 Jun 2011 10:47:55 +0000 (11:47 +0100)]
mfd: Implement tps65910 IRQ cleanup
The tps65910_irq_exit() cleanup function was generating a warning from
sparse due to the lack of a prototype. This wasn't causing GCC warnings
as the driver wasn't cleaning up its IRQs on exit at all so there was no
use of an unprototyped function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Linus Walleij [Thu, 9 Jun 2011 21:57:57 +0000 (23:57 +0200)]
mfd: Clean-up ab8500 register file
This adds a previously undefined test register and removed a
number of double-defined accessory detect registers (they are
already defined higher up in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Linus Walleij [Thu, 9 Jun 2011 21:57:45 +0000 (23:57 +0200)]
mfd: Update ab8500 subdevice list
This synchronize the subdevice entries for the AB8500 MFD driver
with the latest development of subdrivers for things like battery
charging and temperature monitoring.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Margarita Olaya [Thu, 9 Jun 2011 19:50:27 +0000 (14:50 -0500)]
tps65912: add regulator driver
The tps65912 consist of 4 DCDCs and 10 LDOs. The output voltages can be
configured by the SPI or I2C interface, they are meant to supply power
to the main processor and other components.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Peter Huewe [Mon, 6 Jun 2011 20:43:32 +0000 (22:43 +0200)]
mfd: Use kstrtoul_from_user in ab8500
This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Peter Huewe [Mon, 6 Jun 2011 20:43:31 +0000 (22:43 +0200)]
mfd: Use kstrtoul_from_user in ab3550
This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 7 Jun 2011 10:49:42 +0000 (11:49 +0100)]
mfd: Fix WM8994 IRQ register cache restore on resume
When the byte swap was factored out into the per-register I/O functions
the register restore for the IRQ mask cache (which we use and store in
CPU native format for the interrupt handler) was not updated to do a byte
swap when it uses the bulk I/O. Fix this by writing the cache out one
register at a time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 7 Jun 2011 10:47:28 +0000 (11:47 +0100)]
mfd: Support multiple active WM831x AUXADC conversions
The WM831x AUXADC hardware can schedule multiple conversions at once,
allowing higher performance when more than one source is in use as we
can have the hardware start new conversions without having to wait for
a register write.
Take advantage of this in the interrupt driven case, maintaining a list of
callers that are waiting for AUXADC conversions and completing them all
simultaneously. The external interface of the AUXADC is not changed so
there will be limited use of the feature immediately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Sascha Hauer [Thu, 2 Jun 2011 18:18:54 +0000 (19:18 +0100)]
mfd: Allocate wm835x irq descs dynamically
This allows boards to leave the irq_base field unitialized and
prevents them having to reserve irqs in the platform.
pdata can be optional for irq support now. Without pdata the
driver allocates some free irq range. With pdata and irq_base > 0
the driver allocates exactly the specified irq.
Without pdata the irq defaults to IRQF_TRIGGER_LOW.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Thu, 2 Jun 2011 18:18:53 +0000 (19:18 +0100)]
mfd: Refactor wm831x AUXADC handling into a separate file
In preparation for some additional work on the wm831x AUXADC code move the
support into a separate file. This is a simple code motion patch, there
should be no functional changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Thu, 2 Jun 2011 18:18:52 +0000 (19:18 +0100)]
mfd: Read wm831x AUXADC conversion results before acknowledging interrupt
Ensure that there's no possibility of loosing an AUXADC interrupt by reading
the conversion result in the IRQ handler when using interrupts. Otherwise
it's possible that under very heavy load a new conversion could be initiated
before the acknowledgement for a previous interrupt has happened.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
projects / linux-beck.git / log