Arnd Bergmann [Wed, 4 Jan 2006 19:31:22 +0000 (20:31 +0100)]
[PATCH] spufs: dont hold root->isem in spu_forget
spu_forget will do mmput on the DMA address space,
which can lead to lots of other stuff getting triggered.
We better not hold a semaphore here that we might
need in the process.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Wed, 4 Jan 2006 19:55:53 +0000 (19:55 +0000)]
[PATCH] cell: enable pause(0) in cpu_idle
This patch enables support for pause(0) power management state
for the Cell Broadband Processor, which is import for power efficient
operation. The pervasive infrastructure will in the future enable
us to introduce more functionality specific to the Cell's
pervasive unit.
Kumar Gala [Tue, 3 Jan 2006 22:15:21 +0000 (16:15 -0600)]
[PATCH] powerpc: fixing compile issue with !CONFIG_PCI in legacy_serial.c
Only build in support for ISA and PCI cases if we have enabled CONFIG_ISA
and CONFIG_PCI. Additionally, isa_bridge is a global so we shouldn't use
it a parameter name since it gets redefined to NULL when !CONFIG_PCI.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
a easy way to reproduce it is log into the system using ssh and do:
cat >/dev/ttyCPM0
then, switch to minicom and write some stuff on it back to ssh, a control C
produce the oops
this happens because uart_close calls uart_shutdown which frees xmit.buf,
currently used by xchar sending in cpm_uart_tx_pump(), which seems wrong.
the attached patch fixes the oops and also fixes xchar sending.
Haren Myneni [Tue, 27 Dec 2005 23:51:07 +0000 (15:51 -0800)]
[PATCH] powerpc: Fix search for the main interrupt controller
At present, we are not looking at all interrupt controller nodes in the
device tree even though the proper node was not found. This is causing
the system panic. The attached patch will scan all nodes until it finds
the proper interrupt controller type.
Signed-off-by: Haren Myneni <haren@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Kumar Gala [Tue, 20 Dec 2005 22:16:52 +0000 (16:16 -0600)]
[PATCH] powerpc: Add the ability to handle SOC ports in legacy_serial
Add the ability to configure and initialize legacy 8250 serials
ports on an SOC bus. Also, fixed an issue that we would not
configure any serial ports if "linux,stdout-path" was not found.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
The checking of the baudrate in udbg_probe_uart_speed was
too tight and would cause reporting back of the default
baud rate in cases where the computed speed was valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mike Kravetz [Fri, 16 Dec 2005 22:30:35 +0000 (14:30 -0800)]
[PATCH] powerpc: don't add memory to empty node/zone
The system will oops if an attempt is made to add memory to an
empty node/zone. This patch prevents adding memory to an empty
node. The code to dynamically add a node/zone is non-trivial.
This patch is temporary and will be removed when the ability
to dynamically add a node/zone is complete.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Fri, 16 Dec 2005 21:45:27 +0000 (22:45 +0100)]
[PATCH] powerpc: fix two build warnings
Building the arch/powerpc tree currently gives me
two warnings with gcc-4.0:
arch/powerpc/mm/imalloc.c: In function '__im_get_area':
arch/powerpc/mm/imalloc.c:225: warning: 'tmp' may be used uninitialized in this function
arch/powerpc/mm/hugetlbpage.c: In function 'hugetlb_get_unmapped_area':
arch/powerpc/mm/hugetlbpage.c:608: warning: unused variable 'vma'
both fixes are trivial.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Fri, 16 Dec 2005 21:43:46 +0000 (22:43 +0100)]
[PATCH] powerpc: sanitize header files for user space includes
include/asm-ppc/ had #ifdef __KERNEL__ in all header files that
are not meant for use by user space, include/asm-powerpc does
not have this yet.
This patch gets us a lot closer there. There are a few cases
where I was not sure, so I left them out. I have verified
that no CONFIG_* symbols are used outside of __KERNEL__
any more and that there are no obvious compile errors when
including any of the headers in user space libraries.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Fri, 16 Dec 2005 03:49:25 +0000 (14:49 +1100)]
[PATCH] powerpc: Fix iSeries bug in VMALLOCBASE/VMALLOC_START consolidation
Oops, forgot to compile the VMALLOCBASE/VMALLOC_START patch on
iSeries. VMALLOC_START is defined in pgtable.h whereas previously
VMALLOCBASE was previously defined in page.h. lparmap.c needs to be
updated appropriately.
Booted on iSeries RS64 (now).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andy Fleming [Fri, 16 Dec 2005 02:02:04 +0000 (20:02 -0600)]
[PATCH] powerpc: G4+ oprofile support
This patch adds oprofile support for the 7450 and all its multitudinous
derivatives.
* Added 7450 (and derivatives) support for oprofile
* Changed e500 cputable to have oprofile model and cpu_type fields
* Added support for classic 32-bit performance monitor interrupt
* Cleaned up common powerpc oprofile code to be as common as possible
* Cleaned up oprofile_impl.h to reflect 32 bit classic code
* Added 32-bit MMCRx bitfield definitions and SPR numbers
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes pci_address_to_pio() to return an unsigned long (to be safe)
and fixes a bug in the implementation that caused it to return a bogus
IO port number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Wed, 14 Dec 2005 05:08:40 +0000 (16:08 +1100)]
[PATCH] powerpc: Replace VMALLOCBASE with VMALLOC_START
On ppc64, we independently define VMALLOCBASE and VMALLOC_START to be
the same thing: the start of the vmalloc() area at 0xd000000000000000.
VMALLOC_START is used much more widely, including in generic code, so
this patch gets rid of the extraneous VMALLOCBASE.
This does require moving the definitions of region IDs from page_64.h
to pgtable.h, but they don't clearly belong in the former rather than
the latter, anyway. While we're moving them, clean up the definitions
of the REGION_IDs:
- Abolish REGION_SIZE, it was only used once, to define
REGION_MASK anyway
- Define the specific region ids in terms of the REGION_ID()
macro.
- Define KERNEL_REGION_ID in terms of PAGE_OFFSET rather than
KERNELBASE. It amounts to the same thing, but conceptually this is
about the region of the linear mapping (which starts at PAGE_OFFSET)
rather than of the kernel text itself (which is at KERNELBASE).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch enabling the new G5's with U4 broke initialization of the DART
driver, causing it to trigger a BUG_ON for a case that is actually
valid. This patch fixes it:
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Experimental support for new G5 Macs (#2)
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
linas [Tue, 13 Dec 2005 19:46:36 +0000 (13:46 -0600)]
[PATCH] powerpc: export PCI fixup routine
There is code in the RPAPHP directory that is identical to this routine;
I'll be removing that code in an upcoming patch, but this patch is needed
to expose the function to make it callable.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Anton Blanchard [Mon, 12 Dec 2005 19:56:47 +0000 (06:56 +1100)]
[PATCH] ppc64: Add NUMA cpu summary at boot
We used to print a NUMA cpu summary at boot before the hotplug cpu code
was added. This has been useful for catching machine configuration as
well as firmware bugs in the past.
This patch restores that functionality. An example of the output is:
Node 0 CPUs: 0-7
Node 1 CPUs: 8-15
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Fri, 9 Dec 2005 18:21:44 +0000 (19:21 +0100)]
[PATCH] powerpc: fix large nvram access
/dev/nvram uses the user-provided read/write size
for kmalloc, which fails, if a large number is passed.
This will always use a single page at most, which
can be expected to succeed.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc/cell: add iommu support for larger memory
So far, the iommu code was hardwired to a linear mapping
between 0x20000000 and 0x40000000, so it could only support
512MB of RAM.
This patch still keeps the linear mapping, but looks for
proper ibm,dma-window properties to set up larger windows,
this makes the maximum supported RAM size 2GB.
If there is anything unusual about the dma-window properties,
we fall back to the old behavior.
We also support switching off the iommu completely now
with the regular iommu=off command line option.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Fri, 9 Dec 2005 18:04:15 +0000 (19:04 +0100)]
[PATCH] spufs: fix module refcount race
One of the two users of spufs_calls.owner still has a race
when calling try_module_get while the module is removed.
This makes it use the correct instance of owner.
Noticed by Milton Miller.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Tue, 6 Dec 2005 03:52:29 +0000 (22:52 -0500)]
[PATCH] cell: add platform detection code
I can't really get a conclusive answer from the firmware
people what to check for, so I just try scanning for
anything that starts with "IBM,CPB", which should be
correct for all hardware produced so far and for
systemsim.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Tue, 6 Dec 2005 03:52:27 +0000 (22:52 -0500)]
[PATCH] spufs: fix mailbox polling
Handling mailbox interrupts was broken in multiple respects,
the combination of which was hiding the bugs most of the time.
- The ibox interrupt mask was open initially even though there
are no waiters on a newly created SPU.
- Acknowledging the mailbox interrupt did not work because
it is level triggered and the mailbox data is never retrieved
from inside the interrupt handler.
- The interrupt handler delivered interrupts with a disabled
mask if another interrupt is triggered for the same class
but a different mask.
- The poll function did not enable the interrupt if it had not
been enabled, so we might run into the poll timeout if none of
the other bugs saved us and no signal was delivered.
We probably still have a similar problem with blocking
read/write on mailbox files, but that will result in extra
wakeup in the worst case, not in incorrect behaviour.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reduces lock complexity of SPU scheduler, particularly
for involuntary preemptive switches. As a result the new code
does a better job of mapping the highest priority tasks to SPUs.
Lock complexity is reduced by using the system default workqueue
to perform involuntary saves. In this way we avoid nasty lock
ordering problems that the previous code had. A "minimum timeslice"
for SPU contexts is also introduced. The intent here is to avoid
thrashing.
While the new scheduler does a better job at prioritization it
still does nothing for fairness.
From: Mark Nutter <mnutter@us.ibm.com> Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Tue, 6 Dec 2005 03:52:25 +0000 (22:52 -0500)]
[PATCH] spufs: Improved SPU preemptability.
This patch makes it easier to preempt an SPU context by
having the scheduler hold ctx->state_sema for much shorter
periods of time.
As part of this restructuring, the control logic for the "run"
operation is moved from arch/ppc64/kernel/spu_base.c to
fs/spufs/file.c. Of course the base retains "bottom half"
handlers for class{0,1} irqs. The new run loop will re-acquire
an SPU if preempted.
From: Mark Nutter <mnutter@us.ibm.com> Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Tue, 6 Dec 2005 03:52:21 +0000 (22:52 -0500)]
[PATCH] spufs: Make all exports GPL-only
This changes all exported symbols of spufs to EXPORT_SYMBOL_GPL.
The spu_ibox_read/spu_wbox_write symbols are not exported
any more when the scheduler patch is applied.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Add support for "linux,usable-memory" on memory nodes
Milton has proposed that we should support a "linux,usable-memory" property
on memory nodes which describes, in preference to "reg", the regions of memory
Linux should use.
This facility is required for kdump to inform the second kernel which memory
it should use.
Signed-off-by: Haren Myneni <haren@us.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Haren Myneni <haren@us.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Parse crashkernel= parameter in first kernel
This patch adds code to parse and setup the crash kernel resource in the
first kernel. PPC64 ignores the @x part, we always run at 32 MB.
Signed-off-by: Haren Myneni <haren@us.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Add arch dependent basic infrastructure for Kdump.
Implementing the machine_crash_shutdown which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Disable the
interrupts, shootdown cpus using debugger IPI and collect regs
for all CPUs.
elfcorehdr= specifies the location of elf core header stored by
the crashed kernel. This command line option will be passed by
the kexec-tools to capture kernel.
savemaxmem= specifies the actual memory size that the first kernel
has and this value will be used for dumping in the capture kernel.
This command line option will be passed by the kexec-tools to
capture kernel.
Signed-off-by: Haren Myneni <haren@us.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Fixups for kernel linked at 32 MB
There's a few places where we need to fix things up for the kernel to work
if it's linked at 32MB:
- platforms/powermac/smp.c
To start secondary cpus on pmac we patch the reset vector, which is fine.
Except if we're above 32MB we don't have enough bits for an absolute branch,
it needs to relative.
- kernel/head_64.s
- A few branches in the cpu hold code need to load the full target address
and do a bctr.
- after_prom_start needs to load PHYSICAL_START as the dest address, not 0.
- The exception prolog needs to load the low word of the target adddress,
not just the low halfword.
- Fixup handling of the initial stab address.
- kernel/setup_64.c
smp_release_cpus() needs to write 1 to the spinloop flag near 0, not 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Reroute interrupts from 0 + offset to PHYSICAL_START + offset
Regardless of where the kernel's linked we always get interrupts at low
addresses. This patch creates a trampoline in the first 3 pages of memory,
where interrupts land, and patches those addresses to jump into the real
kernel code at PHYSICAL_START.
We also need to reserve the trampoline code and a bit more in prom.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Create a trampoline for the fwnmi vectors
The fwnmi vectors can be anywhere < 32 MB, so we need to use a trampoline
for them. The kdump kernel will register the trampoline addresses, which will
then jump up to the real code above 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mike Kravetz [Mon, 5 Dec 2005 20:06:42 +0000 (12:06 -0800)]
[PATCH] powerpc: numa placement for dynamically added memory
This places dynamically added memory within the appropriate
numa node. A new routine hot_add_scn_to_nid() replicates most of
the memory scanning code in parse_numa_properties().
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Separate usage of KERNELBASE and PAGE_OFFSET
This patch separates usage of KERNELBASE and PAGE_OFFSET. I haven't
looked at any of the PPC32 code, if we ever want to support Kdump on
PPC we'll have to do another audit, ditto for iSeries.
This patch makes PAGE_OFFSET the constant, it'll always be 0xC * 1
gazillion for 64-bit.
To get a physical address from a virtual one you subtract PAGE_OFFSET,
_not_ KERNELBASE.
KERNELBASE is the virtual address of the start of the kernel, it's
often the same as PAGE_OFFSET, but _might not be_.
If you want to know something's offset from the start of the kernel
you should subtract KERNELBASE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a bunch of code that compares an address with KERNELBASE to see if
it's a "kernel address", ie. >= KERNELBASE. The proper test is actually to
compare with PAGE_OFFSET, since we're going to change KERNELBASE soon.
So replace all of them with an is_kernel_addr() macro that does that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andy Whitcroft [Tue, 29 Nov 2005 19:25:54 +0000 (19:25 +0000)]
[PATCH] powerpc32: fix definition of distribute_irqs
When we select ppc32 under the powerpc architecture we get the
error below. This relates to defining distribute_irqs when this
configuratiom option is undefined.
CC arch/powerpc/sysdev/mpic.o
.../arch/powerpc/sysdev/mpic.c: In function `mpic_setup_this_cpu':
.../arch/powerpc/sysdev/mpic.c:788: error: `CONFIG_IRQ_ALL_CPUS'
undeclared (first use in this function)
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andy Whitcroft [Tue, 29 Nov 2005 19:20:55 +0000 (19:20 +0000)]
[PATCH] powerpc32: clean up available memory models
Clean up the currently available memory models for ppc32 under
the powerpc architecture. We need FLATMEM for ppc32: enable it.
SPARSEMEM is not parameterised for ppc32 so disable that. Take this
opportunity to clean up white space for FLATMEM_ENABLE.
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mike Kravetz [Wed, 30 Nov 2005 21:47:23 +0000 (13:47 -0800)]
[PATCH] powerpc: Minor numa memory code cleanup
Here is an updated version of the patch that panics if no memory is
found as Nathan suggested. I'm still concerned that panic strings
(not just the one added here) at this stage of booting do not show
up on my system. But, that is an issue separate from this patch.
Combine get_mem_*_cells() routines to avoid multiple memory node
lookups. Added missing of_node_put() call. Changed variable names
to help with some confusion as to meaning.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the OF address parsers to return the IO flags
indicating the type of address obtained. It also adds a PCI
call for converting physical addresses that hit IO space into
into IO tokens, and add routines that return the translated
addresses into struct resource
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
The udbg low level io layer has an issue with udbg_getc() returning a
char (unsigned on ppc) instead of an int, thus the -1 if you had no
available input device could end up turned into 0xff, filling your
display with bogus characters. This fixes it, along with adding a little
blob to xmon to do a delay before exiting when getting an EOF and fixing
the detection of ADB keyboards in udbg_adb.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andy Whitcroft [Wed, 30 Nov 2005 17:34:50 +0000 (17:34 +0000)]
[PATCH] powerpc: powermac adb fix dependency on btext_drawchar
udbg_adb_init() has become dependent on btext_drawchar, even when
BOOTX_TEXT support is not selected. This leads to the error below.
Make the check dependant on BOOTX_TEXT.
LD .tmp_vmlinux1
arch/powerpc/platforms/built-in.o(.toc1+0xa40): undefined
reference to `btext_drawchar'
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:52:16 +0000 (18:52 -0600)]
[PATCH] powerpc: migrate common PCI hotplug code
23-rpaphp-migrate.patch (parts)
This patch moves some pci device add & remove code from the PCI
hotplug directory to the arch/powerpc/kernel directory, and cleans
it up a tad. The primary reason for this is that the code performs
some fairly generic operations that are shared with the PCI error
recovery code (living in the arch/powerpc/kernel directory).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:51:31 +0000 (18:51 -0600)]
[PATCH] powerpc: PCI hotplug common code elimination
20-rpaphp-eeh-cleanup.patch
This patch move some code from the rpaphp directory, to the powerpc
directory, where it should have been all along (Among other things, I
need it in the powerpc directory for the PCI error recovery.)
Please note that patch affects TWO maintainers: Paul, after applying
the powerpc part, please ask that GregKH appli the PCI part. It is safe
to have the powerpc part go in first. It would be bad to have the
PCI part go in first.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mike Kravetz [Tue, 29 Nov 2005 00:33:24 +0000 (16:33 -0800)]
[PATCH] powerpc: Minor numa memory code cleanup
I started to add missing of_node_put() calls to the routines that
determine the number of cells for memory. Decided to combine the
routines instead of making separate node lookups. Changed variable
names to help with some confusion as to meaning.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Woodhouse [Sat, 26 Nov 2005 14:44:47 +0000 (14:44 +0000)]
[PATCH] ppc: Make ARCH=ppc build again with new syscall path
This makes ARCH=ppc build in your powerpc tree again, with the new
syscall entry/exit path.
Still doesn't actually boot on my Pegasos; the last thing I see is
'MMU:exit'. But at least it builds -- I'll look at why it doesn't boot
later, so that I can see if the mv643xx_eth actually works with ARCH=ppc
(it doesn't with ARCH=powerpc; two in every three packets I receive are
offset by 4 bytes).
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Marcelo Tosatti [Thu, 24 Nov 2005 13:32:09 +0000 (11:32 -0200)]
[PATCH] ppc32: m8xx watchdog update
This updates m8xx_wdt as follows:
1) Remove now obsolete fpos check in the write() function. The driver is
currently non functional due to this bug.
2) Use in/out macros for register access.
3) Allows m8xx_wdt to use a kernel timer instead of the builtin RTC/PIT
for keep-alive trigger (which is responsible for servicing the watchdog
until an userspace application takes over). For instance Cyclades PRxK
boards (MPC 855T based) have a non-functional internal RTC/PIT unit.
Behaviour for boards with RTC/PIT is unchaged.
4) The last change required moving the RTCSC register setting code
to a weak function which can be overriden by board specific files.
Otherwise the timer init code trashes the register making it impossible
for m8xx_wdt to detect the situation.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Woodhouse [Thu, 24 Nov 2005 17:36:20 +0000 (17:36 +0000)]
[PATCH] Fix code that saves NVGPRS in 32-bit signal frame
On Thu, 2005-11-24 at 12:51 +0000, David Woodhouse wrote:
> Somehow this one slipped through the cracks; when we ended up in
> do_signal() on a 32-bit kernel but without having the caller-saved
> registers into the regs, we didn't set the TIF_SAVE_NVGPRS flag to
> ensure they got saved later.
Oh, and if we actually set the flag, then we fairly quickly find out
that I was a bit overzealous in copying code from entry_64.S ... :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Woodhouse [Thu, 24 Nov 2005 12:51:40 +0000 (12:51 +0000)]
[PATCH] Save NVGPRS in 32-bit signal frame
Somehow this one slipped through the cracks; when we ended up in
do_signal() on a 32-bit kernel but without having the caller-saved
registers into the regs, we didn't set the TIF_SAVE_NVGPRS flag to
ensure they got saved later.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Woodhouse [Thu, 24 Nov 2005 17:08:56 +0000 (17:08 +0000)]
[PATCH] powerpc: serial port discovery: cope with broken firmware
On Tue, 2005-11-22 at 15:49 +1100, Benjamin Herrenschmidt wrote:
> This moves the discovery of legacy serial ports to a separate file,
> makes it common to ppc32 and ppc64, and reworks it to use the new OF
> address translators to get to the ports early. This new version can also
> detect some PCI serial cards using legacy chips and will probably match
> those discovered port with the default console choice.
This makes it deal with the fact that the Pegasos firmware reports that
its clock frequency is zero...
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 24 Nov 2005 05:51:31 +0000 (16:51 +1100)]
[PATCH] powerpc: Remove some unneeded fields from the paca
This patch removes several unnecessary fields from the paca:
- next_jiffy_update_tb was simply unused. Remove trivially.
- The exdsi exception save area was not used. There were plans to use
it, but they never seem to have gone anywhere. If they ever do, we
can put it back. Remove from the paca, and from asm-offsets.c
- The default_decr field was used from asm, but was only ever assigned
the value of tb_ticks_per_jiffy. Just access tb_ticks_per_jiffy from
asm directly instead.
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 24 Nov 2005 05:34:45 +0000 (16:34 +1100)]
[PATCH] powerpc: Remove ItLpRegSave area from the paca
On iSeries, the paca contains, amongst other things an ItLpRegSave
structure used by the hypervisor to save registers. The hypervisor
locates this area through a pointer at the beginning of the paca, so
the structure itself can be located elsewhere. This patch moves the
reg_save area out into its own array. This reduces the amount of
iSeries specific gunk which is visible to general powerpc code via
paca.h
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 24 Nov 2005 03:16:15 +0000 (14:16 +1100)]
[PATCH] powerpc: Make hugepage mappings respect hint addresses
Currently, the powerpc version of hugetlb_get_unmapped_area() entirely
ignores the hint address. The only way to get a hugepage mapping at a
specified address is with MAP_FIXED, in which case there's no way
(short of parsing /proc/self/maps) for userspace to tell if it will
clobber an existing mapping. This is inconvenient, so the patch below
makes hugepage mappings use the given hint address if possible.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Wed, 16 Nov 2005 07:10:40 +0000 (18:10 +1100)]
powerpc: use end_IRQ for iseries irqs
Encode the sub bus number into the real irq number (even though it
is always zero for now) so that we have enough information to do
the EOI in iseries_end_IRQ.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[PATCH] powerpc: Add back support for booting from BootX (#2)
ARCH=powerpc couldn't boot from BootX as it uses a "different" way of
getting in the kernel. This patch adds the necessary trampolines,
creating a flattened device-tree from the tree passed from MacOS, and
initializing the btext engine early for really-early debugging.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.
Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.
It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Parsing addresses extracted from Open Firmware isn't a simple matter. We
have various bits of code that try to do it in various place, including
some heuristics in prom.c that pre-parse addresses at boot and fill
device-nodes "addrs", but those are dodgy at best and I want to
deprecate them. So this patch introduces a new set of routines that
should be capable of parsing most types of addresses and translating
them into CPU physical addresses. It currently works for things on PCI
busses and ISA busses and should work on "standard" busses like the root
bus or the MacIO bus that don't put funky flags in addresses. If you
have other bus types that do use funky flags, you'll have to add new bus
type translators, which is fairly easy.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
projects / linux-beck.git / log