Fix fairly sad NOR-specific bug - during FS building ic->scan_dents
isn't zero, but jffs2_mark_node_obsolete() migt be called it tries to
finde the ic corresponding to ref - this requires ic->scan_dents = 0.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Joern Engel [Wed, 23 Feb 2005 19:37:11 +0000 (19:37 +0000)]
[MTD] Use after free, found by the Coverity tool
Signed-off-by: Alexander Nyberg <alexn@dsv.su.se> Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Tue, 22 Feb 2005 21:56:49 +0000 (21:56 +0000)]
[MTD] NAND: Check command timeout
Check timeout while we wait for the command to finish. No worry about a
false result. This prevents deadlocking when detecting an unknown number
of chips and is useful for removable media too.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Ben Dooks [Mon, 14 Feb 2005 16:27:38 +0000 (16:27 +0000)]
[MTD] Fixup probing logic for single 16bit devices
The change to the generic probe to look for the
smallest width of chip first is causing some problems
on boards with a single 16bit device.
The problem seems to be the jedec_match() is truncating
the device-id read from the table to match against the
one read from the hardware, causing a match against the
partial id of some chips with 16bit IDs (such as the
SST39LF160)
This fixes things for my own board, but something may
need to be done if the same problem is exhibited for
chips with an 8bit ID
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[MTD] NAND: Read only OOB bytes during bad block scan
When scanning NAND for bad blocks, don't read the whole page, read
only needed OOB bytes instead. Also check the return code of the
nand_read_raw() function. Correctly free the this->bbt array in
case of failure. Tested with Large page NAND.
Fix debugging message.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew Victor [Wed, 9 Feb 2005 09:24:26 +0000 (09:24 +0000)]
[JFFS2] Use a single config option for write buffer support
This patch replaces the current CONFIG_JFFS2_FS_NAND, CONFIG_JFFS2_FS_NOR_ECC
and CONFIG_JFFS2_FS_DATAFLASH with a single configuration option -
CONFIG_JFFS2_FS_WRITEBUFFER.
The only functional change of this patch is that the slower div/mod
calculations for SECTOR_ADDR(), PAGE_DIV() and PAGE_MOD() are now always
used when CONFIG_JFFS2_FS_WRITEBUFFER is enabled.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew Victor [Wed, 9 Feb 2005 09:17:45 +0000 (09:17 +0000)]
[JFFS2] Add support for JFFS2-on-Dataflash devices.
For Dataflash, can_mark_obsolete = false and the NAND write buffering
code (wbuf.c) is used.
Since the DataFlash chip will automatically erase pages when writing,
the cleanmarkers are not needed - so cleanmarker_oob = false and
cleanmarker_size = 0
DataFlash page-sizes are not a power of two (they're multiples of 528
bytes). The SECTOR_ADDR macro (added in the previous core patch) is
replaced with a (slower) div/mod version if CONFIG_JFFS2_FS_DATAFLASH is
selected.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew Victor [Wed, 9 Feb 2005 09:09:05 +0000 (09:09 +0000)]
[JFFS2] Core changes required to support JFFS2-on-Dataflash devices.
DataFlash page-sizes are not a power of two (they're multiples of 528
bytes). There are a few places in JFFS2 code where sector_size is used
as a bitmask. A new macro (SECTOR_ADDR) was defined to calculate these
sector addresses. For non-DataFlash devices, the original (faster)
bitmask operation is still used.
In scan.c, the EMPTY_SCAN_SIZE was a constant of 1024.
Since this could be larger than the sector size of the DataFlash, this
is now basically set to MIN(sector_size, 1024).
Addition of a jffs2_is_writebuffered() macro.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Nicolas Pitre [Tue, 8 Feb 2005 17:45:55 +0000 (17:45 +0000)]
[MTD] User interface to Protection Registers
This is implemented using a ioctl to switch the MTD char device into
one of the different OTP "modes", at which point read/write/seek can
operate on the selected OTP area. Also some extra ioctls to query
for size and lock protection segments or groups. Some example user
space utilities are provided.
Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Nicolas Pitre [Tue, 8 Feb 2005 17:11:19 +0000 (17:11 +0000)]
[MTD] Support for protection register support on Intel FLASH chips
This enables support for reading, writing and locking so called
"Protection Registers" present on some flash chips.
A subset of them are pre-programmed at the factory with a
unique set of values. The rest is user-programmable.
Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
David A. Marlin [Mon, 24 Jan 2005 20:40:15 +0000 (20:40 +0000)]
[MTD] rtc_from4 error status check, disable virtual erase blocks
Added routine to perform extra error status checks on erase and write
failures to determine if errors are correctable.
Added option to prevent JFFS2 from using virtual erase blocks.
Performed minor cleanup on whitespace and comments.
Signed-off-by: David A. Marlin <dmarlin@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
David A. Marlin [Mon, 17 Jan 2005 18:35:25 +0000 (18:35 +0000)]
[MTD] NAND workaround for AG-AND disturb issue. AG-AND recovery
Added workaround for Renesas AG-AND chips "disturb" issue
for Bad Block Table.
Added support for the device recovery command sequence
for Renesas AG-AND chips.
Signed-off-by: David A. Marlin <dmarlin@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Wed, 18 May 2005 22:39:33 +0000 (15:39 -0700)]
[PATCH] prevent NULL mmap in topdown model
Prevent the topdown allocator from allocating mmap areas all the way
down to address zero.
We still allow a MAP_FIXED mapping of page 0 (needed for various things,
ranging from Wine and DOSEMU to people who want to allow speculative
loads off a NULL pointer).
Stephen Tweedie [Wed, 18 May 2005 15:47:17 +0000 (11:47 -0400)]
[PATCH] Avoid console spam with ext3 aborted journal.
Avoid console spam with ext3 aborted journal.
ext3 usually reports error conditions that it detects in its environment.
But when its journal gets aborted due to such errors, it can sometimes
continue to report that condition forever, spamming the console to such
an extent that the initial first cause of the journal abort can be lost.
When the journal aborts, we put the filesystem into readonly mode. Most
subsequent filesystem operations will get rejected immediately by checks
for MS_RDONLY either in the filesystem or in the VFS. But some paths do
not have such checks --- for example, if we continue to write to a file
handle that was opened before the fs went readonly. (We only check for
the ROFS condition when the file is first opened.) In these cases, we
can continue to generate log errors similar to
EXT3-fs error (device $DEV) in start_transaction: Journal has aborted
for each subsequent write.
There is really no point in generating these errors after the initial
error has been fully reported. Specifically, if we're starting a
completely new filesystem operation, and the filesystem is *already*
readonly (ie. the ext3 layer has already detected and handled the
underlying jbd abort), and we see an EROFS error, then there is simply
no point in reporting it again.
Signed-off-by: Stephen Tweedie <sct@redhat.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stephen Tweedie [Wed, 18 May 2005 15:22:31 +0000 (11:22 -0400)]
[PATCH] Fix filp being passed through raw ioctl handler
Don't pass meaningless file handles to block device ioctls.
The recent raw IO ioctl-passthrough fix started passing the raw file
handle into the block device ioctl handler. That's unlikely to be
useful, as the file handle is actually open on a character-mode raw
device, not a block device, so dereferencing it is not going to yield
useful results to a block device ioctl handler.
Previously we just passed NULL; also not a value that can usefully
be dereferenced, but at least if it does happen, we'll oops instead of
silently pretending that the file is a block device, so NULL is the more
defensive option here. This patch reverts to that behaviour.
Noticed by Al Viro.
Signed-off-by: Stephen Tweedie <sct@redhat.com> Acked-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Brownell [Thu, 12 May 2005 19:06:27 +0000 (12:06 -0700)]
[PATCH] Driver Core: remove driver model detach_state
The driver model has a "detach_state" mechanism that:
- Has never been used by any in-kernel drive;
- Is superfluous, since driver remove() methods can do the same thing;
- Became buggy when the suspend() parameter changed semantics and type;
- Could self-deadlock when called from certain suspend contexts;
- Is effectively wasted documentation, object code, and headspace.
This removes that "detach_state" mechanism; net code shrink, as well
as a per-device saving in the driver model and sysfs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 9 May 2005 15:07:00 +0000 (08:07 -0700)]
[PATCH] Driver Core: pm diagnostics update, check for errors
This patch includes various tweaks in the messaging that appears during
system pm state transitions:
* Warn about certain illegal calls in the device tree, like resuming
child before parent or suspending parent before child. This could
happen easily enough through sysfs, or in some cases when drivers
use device_pm_set_parent().
* Be more consistent about dev_dbg() tracing ... do it for resume() and
shutdown() too, and never if the driver doesn't have that method.
* Say which type of system sleep state is being entered.
Except for the warnings, these only affect debug messaging.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Scott Murray [Mon, 9 May 2005 21:36:27 +0000 (17:36 -0400)]
[PATCH] PCI Hotplug: remove pci_visit_dev
If my CPCI hotplug update patch is applied, then there are no longer any
in tree users of the pci_visit_dev API, and it and its related code can be
removed.
Signed-off-by: Scott Murray <scottm@somanetworks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Scott Murray [Mon, 9 May 2005 21:31:50 +0000 (17:31 -0400)]
[PATCH] PCI Hotplug: CPCI update
[PATCH] CPCI: update
I have finally done some work to update the CompactPCI hotplug driver to
fix some of the outstanding issues in 2.6:
- Added adapter and latch status ops so that those files will get created
by the current PCI hotplug core. This used to not be required, but
seems to be now after some of the sysfs rework in the core.
- Replaced slot list spinlock with a r/w semaphore to avoid any potential
issues with sleeping. This quiets all of the runtime warnings.
- Reworked interrupt driven hot extraction handling to remove need for a
polling operator for ENUM# status. There are a lot of boards that only
have an interrupt driven by ENUM#, so this lowers the bar to entry.
- Replaced pci_visit_dev usage with better use of the PCI core functions.
The new code is functionally equivalent to the previous code, but the
use of pci_enable_device on insert needs to be investigated further, as
I need to do some more testing to see if it is still necessary.
Signed-off-by: Scott Murray <scottm@somanetworks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dely Sy [Sat, 7 May 2005 00:19:09 +0000 (17:19 -0700)]
[PATCH] PCI Hotplug: get pciehp to work on the downstream port of a switch
Here is the updated patch to get pciehp driver to work for downstream
port of a switch and handle the difference in the offset value of PCI
Express capability list item of different ports.
Signed-off-by: Dely Sy <dely.l.sy@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dely Sy [Thu, 5 May 2005 18:57:25 +0000 (11:57 -0700)]
[PATCH] PCI Hotplug: Fix echoing 1 to power file of enabled slot problem with SHPC driver
Here is a patch to fix the problem of echoing 1 to "power" file
to enabled slot causing the slot to power down, and echoing 0
to disabled slot causing shpchp_disabled_slot() to be called
twice. This problem was reported by kenji Kaneshige.
Thanks,
Dely
Signed-off-by: Dely Sy <dely.l.sy@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] fix memory scribble in arch/i386/pci/fixup.c
The GET_INDEX() macro should use just the low three bits of the devfn,
otherwise we have a memory scribble in pcie_rootport_aspm_quirk that
overwrites ptype_all
Fix it to be more careful about its arguments while at it.
- remove enable_ci, ci interface is assumed to be present if the saa7113
is not found.
- reduce the delay when checking for saa7113
- clean up the cam reset according to specifications
- turn off Vcc to the cam slot if cam is removed or fails reset
- remove cam reset in ciintf_init
- clean up printks (KERN_)
- move gpio setting into saa7113_init
- clean up unreadable frontend_init
(Kenneth Aafloy)
Signed-off-by: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] dvb: modified dvb_register_adapter() to avoid kmalloc/kfree
Modified dvb_register_adapter() to avoid kmalloc/kfree. Drivers have to embed
struct dvb_adapter into their private data struct from now on. (Andreas
Oberritter)
Signed-off-by: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] dvb: make needlessly global code static or drop it
- make needlessly global code static
- #if 0 the following unused global functions:
- ttpci/av7110_hw.c: av7110_reset_arm
- ttpci/av7110_hw.c: av7110_send_ci_cmd
- frontends/mt352.[ch]: drop mt352_read
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-beck.git / log