[MIPS] Add debugfs files to show fpuemu statistics
Export contents of struct mips_fpu_emulator_stats via debugfs.
There is no way to read these statistics for now but they (at least
the "emulated" count) might be sometimes useful for performance tuning
on FPU-less CPUs.
[MIPS] rbtx4938: Fix secondary PCIC and glue internal NICs
* Fix pci ops for secondary PCIC
* Do not reserve 1MB for PCI MEM region (leave PCIBIOS_MIN_MEM zero)
* Use platform_device to provide ethernet addresses for internal NICs.
(background: TX49XX SoCs include PCI NIC (TC35815 compatible)
connected via its internal PCI bus, but the NIC's PROM interface is
not connected to SEEPROM. So we must provide its ethernet address
by another way.)
* Check return value of early_read_config_word()
Atsushi Nemoto [Fri, 29 Jun 2007 13:34:53 +0000 (22:34 +0900)]
[MIPS] tc35815: Load MAC address via platform_device
TX49XX SoCs include PCI NIC (TC35815 compatible) connected via its
internal PCI bus, but the NIC's PROM interface is not connected to
SEEPROM. So we must provide its ethernet address by another way.
Atsushi Nemoto [Mon, 25 Jun 2007 16:14:01 +0000 (01:14 +0900)]
[MIPS] Make ioremap() work on TX39/49 special unmapped segment
TX39XX and TX49XX have "reserved" segment in CKSEG3 area.
0xff000000-0xff3fffff on TX49XX and 0xff000000-0xfffeffff on TX39XX
are reserved (unmapped, uncached). Controllers on these SoCs are
placed in this segment.
This patch add plat_ioremap() and plat_iounmap() to override default
behavior and implement these hooks for TX39/TX49.
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[MIPS] Enable support for the userlocal hardware register
Which will cut down the cost of RDHWR $29 which is used to obtain the
TLS pointer and so far being emulated in software down to a single cycle
operation.
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:35 +0000 (17:46 +0200)]
[MIPS] Fix PHYS_OFFSET for 64-bits kernels with 32-bits symbols
The current implementation of __pa() for 64-bits kernels with 32-bits
symbols is broken. In this configuration, we need 2 values for
PAGE_OFFSET, one in XKPHYS and the other in CKSEG0 space.
When the value in CKSEG0 space is used, it doesn't take into account
of PHYS_OFFSET. Even worse we can't redefine this value.
The patch restores CPHYSADDR() but in __pa()'s implementation because
it removes the need of 2 PAGE_OFFSET.
OTOH, CPHYSADDR() is quite bad when dealing with mapped kernels. So
this patch assumes there's no need to deal with such kernel in 64-bits
world.
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:33 +0000 (17:46 +0200)]
[MIPS] Make PAGE_OFFSET aware of PHYS_OFFSET
For platforms that use PHYS_OFFSET and do not use a mapped kernel,
this patch automatically adds PHYS_OFFSET into PAGE_OFFSET.
Therefore there are no more needs for them to redefine PAGE_OFFSET.
For mapped kernel, they need to redefine PAGE_OFFSET anyways.
No point in adding yet another #ifdef for Loongson since all this mask is
being used for is converting an XKPHYS address into a physical address
anyway. So replace all definitions by one with the highest architectural
possible value.
Florian Fainelli [Tue, 22 May 2007 19:44:42 +0000 (21:44 +0200)]
[MIPS] Add generic GPIO to Au1x00
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Atsushi Nemoto [Tue, 29 May 2007 15:38:07 +0000 (00:38 +0900)]
[MIPS] Simplify missing-syscalls for N32 and O32
Use standard missing-syscalls with EXTRA_CFLAGS instead of duplicating
the command. And move the archprepare rule before the archclean rule.
Suggested by Franck Bui-Huu. Also add "echo" to show the target ABI.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (31 commits)
firewire: fw-sbp2: fix DMA mapping of management ORBs
firewire: fw-sbp2: fix DMA mapping of command ORBs
firewire: fw-sbp2: fix DMA mapping of S/G tables
firewire: fw-sbp2: add a boundary check
firewire: fw-sbp2: correctly align page tables
firewire: fw-sbp2: memset wants string.h
firewire: fw-sbp2: use correct speed in sbp2_agent_reset
firewire: fw-sbp2: correctly dereference by container_of
firewire: Document userspace ioctl interface.
firewire: fw-sbp2: implement nonexclusive login
firewire: fw-sbp2: let SCSI shutdown commands through before logout
firewire: fw-sbp2: implement max sectors limit for some old bridges
firewire: simplify a struct type
firewire: support S100B...S400B and link slower than PHY
firewire: optimize gap count with 1394b leaf nodes
firewire: remove unused macro
firewire: missing newline in printk
firewire: fw-sbp2: remove unused struct member
ieee1394: remove old isochronous ABI
ieee1394: sbp2: change some module parameters from int to bool
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: handle cases of volume knobs generating relative values
HID: Logitech keyboard 0xc311 needs reset leds quirk
HID: support for logitech cordless desktop LX500 special mapping
HID: fix autocentering of PID devices
HID: separate quirks for report descriptor fixup
HID: Add NOGET quirk for all NCR devices
HID: support for Petalynx Maxter remote control
HID: fix mismatch between hid-input HUT find/search mapping and the HUT
HID: support for Gameron dual psx adaptor
USB HID: avoid flush_scheduled_work()
HID: Use menuconfig objects
HID: force hid-input for Microsoft SideWinder GameVoice device
HID: input mapping for Chicony KU-0418 tactical pad
HID: make debugging output runtime-configurable
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (75 commits)
Ethernet driver for EISA only SNI RM200/RM400 machines
Extract chip specific code out of lasi_82596.c
ehea: Whitespace cleanup
pasemi_mac: Fix TX interrupt threshold
spidernet: Replace literal with const
r8169: perform RX config change after mac filtering
r8169: mac address change support
r8169: display some extra debug information during startup
r8169: add endianess annotations to [RT]xDesc
r8169: align the IP header when there is no DMA constraint
r8169: add bit description for the TxPoll register
r8169: cleanup
r8169: remove the media option
r8169: small 8101 comment
r8169: confusion between hardware and IP header alignment
r8169: merge with version 8.001.00 of Realtek's r8168 driver
r8169: merge with version 6.001.00 of Realtek's r8169 driver
r8169: prettify mac_version
r8169: populate the hw_start handler for the 8110
r8169: populate the hw_start handler for the 8168
...
Stefan Richter [Mon, 2 Jul 2007 20:07:34 +0000 (22:07 +0200)]
firewire: fw-sbp2: fix DMA mapping of S/G tables
- The CPU must not touch the buffer after it was DMA-mapped.
- The size argument of dma_unmap_single(...page_table...) was bogus.
- Move a comment closer to the code to which it refers to.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 1 Jul 2007 11:56:03 +0000 (13:56 +0200)]
firewire: fw-sbp2: add a boundary check
Add rudimentary check for the case that the page table overflows due to
merging of s/g elements by the IOMMU. This would have lead to
overwriting of arbitrary memory.
After this change I expect that an offending command will be
unsuccessfully retried until the scsi_device is taken offline by SCSI
core. It's a border case and not worth to implement a recovery
strategy.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Acked-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 10 Jun 2007 19:31:36 +0000 (21:31 +0200)]
firewire: support S100B...S400B and link slower than PHY
Use a speed probe to determine the speed over 1394b buses and of nodes
which report a link speed less than their PHY speed.
Log the effective maximum speed of newly created nodes in dmesg.
Also, read the config ROM (except bus info block) at the maximum speed
rather than S100. This isn't a real optimization though because we
still only use quadlet read requests for the entire ROM.
The patch also adds support for S1600 and S3200, although such hardware
does not exist yet.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 24 Jun 2007 13:31:54 +0000 (15:31 +0200)]
ieee1394: remove old isochronous ABI
Based on patch "the scheduled removal of RAW1394_REQ_ISO_{SEND,LISTEN}"
from Adrian Bunk, November 20 2006.
This patch also removes the underlying facilities in ohci1394 and
disables them in pcilynx. That is, hpsb_host_driver.devctl() and
hpsb_host_driver.transmit_packet() are no longer used for iso reception
and transmission.
Since video1394 and dv1394 only work with ohci1394 and raw1394's rawiso
interface has never been implemented in pcilynx, pcilynx is now no
longer useful for isochronous applications.
raw1394 will still handle the request types but will complete the
requests with errors that indicate API version conflicts.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 27 May 2007 21:14:05 +0000 (23:14 +0200)]
ieee1394: eth1394: revert parent device to that in 2.6.20
After ieee1394 was converted away from class_device like the networking
subsystem was already in 2.6.21, eth1394's device may point to the
fw-host device as its parent again like in 2.6.20.
This affects userspace tools which examine the sysfs representation of
eth1394's device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 17 Jun 2007 21:47:45 +0000 (23:47 +0200)]
ieee1394: nodemgr: parallelize between several hosts
Remove the global nodemgr_serialize mutex which enclosed most of the
host thread event loop. This allows for parallelism between several
host adapter cards.
Properly serialize the driver hooks .update(), .suspend(), .resume(),
and .remove() by means of device->sem. These hooks can be called from
outside the host threads' contexts.
Get() and put() the device.driver when calling its hooks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Wed, 4 Jul 2007 21:13:53 +0000 (23:13 +0200)]
ieee1394: raw1394: fix a 32/64-bits compat fix
I was told that only i386 aligns 64 bit integers at 4 bytes boundaries
while all other architectures (32 bit architectures with 64 bit
siblings) align it on 8 bytes boundaries.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Mon, 21 May 2007 16:52:06 +0000 (18:52 +0200)]
ieee1394: raw1394: Add ioctl() for 32bit userland on 64bit kernel, amendment
Pointed out by Arnd Bergmann: PPC32 aligns this at 64bit, IA32 packs
it. A kernel-wide available __compat_u64 which is 4-byte aligned on
AMD64 and IA64 would be nicer though.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Petr Vandrovec [Mon, 7 May 2007 02:14:47 +0000 (04:14 +0200)]
ieee1394: raw1394: Add ioctl() for 32bit userland on 64bit kernel
Add compat_ioctl. Although all structures are more or less same,
raw1394_iso_packets got pointer inside, and raw1394_cycle_timer got unwanted
padding in the middle. I did not add any translation for ioctls passing array
of integers around as integers seem to have same size (32 bits) on all
architectures supported by Linux.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name> Acked-by: Dan Dennedy <dan@dennedy.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
Petr Vandrovec [Mon, 7 May 2007 02:14:47 +0000 (04:14 +0200)]
ieee1394: raw1394: Fix write() for 32bit userland on 64bit kernel
* write(fd, buf, 52) from 32bit app was returning 56. Most of callers did not
care, but some (arm registration) did, and anyway it looks bad if request for
writing 52 bytes returns 56. And returning sizeof anything in 'int' is not
good as well. So all functions now return '0' instead of
sizeof(struct raw1394_request) on success, and write() itself provides correct
return value (it just returns value it was asked to write on success as raw1394
does not do any partial writes at all).
* Related to this was problem that write() could have returned 0 when kernel
state would become corrupted and moved to different state than
opened/initialized/connected. Now it returns -EBADFD which seemed appropriate.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name> Acked-by: Dan Dennedy <dan@dennedy.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
Petr Vandrovec [Mon, 7 May 2007 02:14:47 +0000 (04:14 +0200)]
ieee1394: raw1394: Fix read() for 32bit userland on 64bit kernel
read() always failed with -EFAULT. This was happening due to
raw1394_compat_read copying data to wrong location - access_ok always
failed as 'r' is kernel address, not user. Whole function just tried to
copy data from 'r' to 'r', which is not good.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name> Acked-by: Dan Dennedy <dan@dennedy.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter. Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.
Next patches add automatic detection of some systems using short cables.
Changes:
* Rename hwif->udma_four to hwif->cbl and make it u8.
* Convert all existing users accordingly (use ATA_CBL_* defines while at it).
* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().
* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Junio C Hamano [Mon, 9 Jul 2007 21:17:57 +0000 (23:17 +0200)]
ide_in_drive_list(): "ALL" is not a wildcard anymore
This removes the support to treat "ALL" as a wildcard for
firmware revision. This is made a separate patch, as it will
break out-of-tree ide drivers that feed its own table that uses
"ALL" as the wildcard to ide_in_drive_list().
Signed-off-by: Junio C Hamano <junkio@cox.net> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Dave Jones <davej@redhat.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Junio C Hamano [Mon, 9 Jul 2007 21:17:56 +0000 (23:17 +0200)]
mips au1xxx_ide.h: use NULL as firmware-revision wildcard
This updates the DMA whitelist in MIPS specific au1xxx ide
driver to use NULL instead of "ALL" as the wildcard.
Signed-off-by: Junio C Hamano <junkio@cox.net> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Dave Jones <davej@redhat.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Junio C Hamano [Mon, 9 Jul 2007 21:17:56 +0000 (23:17 +0200)]
ide_in_drive_list(): accept NULL as the wildcard for firmware revision
Earlier, the matching of (model,rev) in ide-dma black/white list
handling was to consider "ALL" in the table to match any
revision. This makes NULL to be also an accepted wildcard, and
changes the entries of tables in ide-dma.c to use NULL.
The code still accepts "ALL" as the wildcard, in order to keep
any out-of-tree ide driver that feeds its own table that uses
"ALL" as the wildcard to ide_in_drive_list() function from
breaking.
Signed-off-by: Junio C Hamano <junkio@cox.net> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Dave Jones <davej@redhat.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
projects / linux-beck.git / log