Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:21 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: skip resetting ETH PHYs
ETH PHYs setup on CL-SOM-AM57X is established in U-Boot along with
bringing them out of reset. This is done by toggling GPIOs belonging
to GPIO2/3 controllers on AM57xx.
Skip resetting ETH PHYs, by adding "ti,no-reset-on-init" to GPIO2/3
controllers DT nodes.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:13 +0000 (20:03 +0200)]
ARM: dts: am57xx: sbc-am57x: add basic board support
SBC-AM57x is a single board computer designed for industrial and
embedded applications. It is based on the Texas Instruments Sitara AM57x
system-on-chip family. SBC-AM57x is implemented with the CL-SOM-AM57x
computer-on-module providing most of the functions, and SB-SOM-AM57x
carrier board providing additional peripheral functions and connectors.
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:07 +0000 (15:55 +0200)]
ARM: dts: sb-som: introduce SB-SOM baseboard
CompuLab SB-SOM baseboard is a carrier board for multiple arm-based SoMs.
It currently supports (with minor adjustments to assembly) CM-T43, CM-T54,
and CM-QS600 modules. It is a building block in the SBC-T43 single board
computer, which consists of cm-t43 on top of sb-som-t43.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Tony Lindgren <tony@atomide.com> Cc: Benoit Cousson <bcousson@baylibre.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:01 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add dual emac support
CM-T43 comes with 2 ethernet ports connected to the cpsw subsystem, which
has 2 modes of operation: switch mode and dual emac mode.
Add the relevant muxing and set it up to work in dual emac mode by
default.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Benoit Cousson <bcousson@baylibre.com> Cc: Rob Herring <robh@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:00 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add NAND support
One of the CompuLab cm-t43 configurations comes with on-board NAND flash as
primary storage. It is partitioned into kernel, dtb, and rootfs partitions.
Add it to the device tree.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Tony Lindgren <tony@atomide.com> Cc: Benoit Cousson <bcousson@baylibre.com> Cc: Rob Herring <robh@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nikita Kiryanov [Tue, 1 Dec 2015 13:54:56 +0000 (15:54 +0200)]
ARM: dts: am437x: cm-t43: add basic support for sbc-t43
Add basic support for SBC-T43: a CM-T43 based single board computer.
CM-T43 is an AM437x based System-on-Module designed to serve as a building
block in embedded applications. SBC-T43 is composed of CM-T43 module on
top of the SB-SOM-T43 baseboard.
Basic support includes UART, GPIO, and I2C.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Rob Herring <robh@kernel.org> Cc: Tony Lindgren <tony@atomide.com> Cc: Benoit Cousson <bcousson@baylibre.com> Cc: Rob Herring <robh@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Vignesh R [Thu, 26 Nov 2015 08:31:26 +0000 (14:01 +0530)]
ARM: dts: dra72-evm: Mark uart1 rxd as wakeup capable
Uart1 rxd is wakeup capable on DRA72 EVM. Hence, mark rxd line as
wakeup capable. This is similar to commit 66b0436977e2c ("ARM: dts:
dra7-evm: Mark uart1 rxd as wakeup capable") for DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Heiko Schocher [Tue, 27 Oct 2015 12:36:36 +0000 (13:36 +0100)]
regulator: tps65217: remove tps65217.dtsi file
remove tps65217.dtsi and adapt all boards, which
used it.
Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Keerthy <j-keerthy@ti.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ilya Ledvich [Tue, 24 Nov 2015 14:02:12 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add support for network device
Add pinmux configurations for RGMII1 based CPSW Ethernet pins and
MDIO pins:
- default configuration required for module in active state,
- sleep configuration required for module in inactive state.
Add mac node with single slave device. Add nodes for davinci_mdio and
cpsw_emac0.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ilya Ledvich [Tue, 24 Nov 2015 14:02:10 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add support for NAND flash
Add pinmux configuration for NAND specific GPMC pins.
Add description for GPMC controller. Add child node for NAND flash
including CM-T335 specific partition table to GPMC node.
Enable error-location module (ELM).
Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ilya Ledvich [Tue, 24 Nov 2015 14:02:09 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add basic support for I2C
Add pinmux configuration for I2C0 and I2C1 pins.
Add description for I2C0 bus, set clock frequency to 400kHz.
Add child nodes for 24c02 EEPROM and em3027 RTC on I2C0 bus.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ilya Ledvich [Tue, 24 Nov 2015 14:02:08 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add initial support
Add basic support for CompuLab cm-t335 module based on AM335X SoC.
CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM)
The module is built around the Texas Instruments Sitara AM3352/4
system-on-chip.
The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board
NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit
Ethernet, CAN bus.
Current patch adds support:
UART0 and GPIO LED
Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
[uri.mashiach@compulab.co.il: the default RAM amount reduced to
128MB to support also the minimal module configuration] Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup UART2 for communication at 3MBps with flow control.
Signed-off-by: Adam Ford <adam.ford@logicpd.com>
[tony@atomide.com: dropped the kim changes, that binding has been removed] Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Fri, 23 Oct 2015 12:27:33 +0000 (07:27 -0500)]
ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively
The development kit schematic expects VAUX1 to be 3.0V. Most users use the development kit as a reference.
The development kit schematic expects VAUX4 to be 1.8V. VAUX4 powers VDDS_CSI2 on processor. If the voltage is too high it could damage the processor.
If it's too low, it won't work.
Andrew F. Davis [Fri, 13 Nov 2015 16:47:27 +0000 (10:47 -0600)]
ARM: dts: am335x-boneblack: Use pinctrl constants and AM33XX_IOPAD macro
Using constants for pinctrl allows better readability and removes
redundancy with comments. AM33XX_IOPAD allows us to use part of the
pinctrl physical address as in the TRM instead of an offset.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap5-uevm.dts: Use OMAP5_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap5-cm-t54: Use OMAP5_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap5-board-common: Use OMAP5_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap4-sdp-es23plus: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap4-panda-es: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap4-panda-common: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap4-panda-a4: Use OMAP4_IOPAD pinmux macro
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: twl4030: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-zoom3: Use OMAP3_*_IOPAD pinmux macros
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-n9: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-n900: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-ldp: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-evm-37xx: Use OMAP3_*_IOPAD pinmux macros
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-beagle-xm: Use OMAP3_*_IOPAD pinmux macros
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-beagle: Use OMAP3_*_IOPAD pinmux macros
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra72-evm: Use DRA7XX_CORE_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra7-evm: Use DRA7XX_CORE_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am57xx-beagle-x15: Use DRA7XX_CORE_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am43x-epos-evm: Use AM4372_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am437x-sk-evm: Use AM4372_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am437x-idk-evm: Use AM4372_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am437x-gp-evm: Use AM4372_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am3517-craneboard: Use OMAP3_CORE1_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-wega: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-phycore-som: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-pepper: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-nano: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-lxm: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-evmsk: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-evm: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-chilisom: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-chiliboard: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-bonegreen: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-bone-common: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am335x-baltos-ir5221: Use AM33XX_IOPAD pinmux macro
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
When the Device Tree source file got merged, some commented pinctrl lines
were left in the file. These are already defined so seems to be a cleanup
that was missed. Delete the unneeded lines from the file.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
pinctrl: Move am4372 and dra7 macros to the the SoC header files
The <dt-bindings/pinctrl/omap.h> header file defines a set of macros
for different SoCs families that falls under the OMAP sub-arch, that
allow to define the padconf register physical address instead of the
register offset from the padconf base.
But the am43xx and dra7xx SoCs families have their own pinctrl header
file so the DTS using these SoCs aren't able to use the AM4372_IOPAD()
and DRA7XX_CORE_IOPAD() macros since <dt-bindings/pinctrl/omap.h> is
not included.
Move the macros to the correct header files so can be used by the DTS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Sun, 22 Nov 2015 23:21:40 +0000 (15:21 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge slub bulk allocator updates from Andrew Morton:
"This missed the merge window because I was waiting for some repairs to
come in. Nothing actually uses the bulk allocator yet and the changes
to other code paths are pretty small. And the net guys are waiting
for this so they can start merging the client code"
More comments from Jesper Dangaard Brouer:
"The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
previous kernel. The present version contains a bug. Vladimir
Davydov noticed it contained a bug, when kernel is compiled with
CONFIG_MEMCG_KMEM (see commit 03ec0ed57ffc: "slub: fix kmem cgroup
bug in kmem_cache_alloc_bulk"). Plus the mem cgroup counterpart in
kmem_cache_free_bulk() were missing (see commit 033745189b1b "slub:
add missing kmem cgroup support to kmem_cache_free_bulk").
I don't consider the fix stable-material because there are no in-tree
users of the API.
But with known bugs (for memcg) I cannot start using the API in the
net-tree"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
Linus Torvalds [Sun, 22 Nov 2015 23:10:57 +0000 (15:10 -0800)]
Merge tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
some reported problems.
All have been in linux-next, full details are in the shortlog below"
* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
tty: Fix tty_send_xchar() lock order inversion
Linus Torvalds [Sun, 22 Nov 2015 21:26:24 +0000 (13:26 -0800)]
Merge tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and iio driver fixes for 4.4-rc2. All of these
are in response to issues that have been reported and have been in
linux-next for a while"
* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
iio: adc: xilinx: Fix VREFN scale
iio: si7020: Swap data byte order
iio: adc: vf610_adc: Fix division by zero error
iio:ad7793: Fix ad7785 product ID
iio: ad5064: Fix ad5629/ad5669 shift
iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
vf610_adc: Fix internal temperature calculation
Linus Torvalds [Sun, 22 Nov 2015 21:15:05 +0000 (13:15 -0800)]
Merge tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes and new device ids for 4.4-rc2. All
have been in linux-next and the details are in the shortlog"
* tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
usblp: do not set TASK_INTERRUPTIBLE before lock
USB: MAINTAINERS: cxacru
usb: kconfig: fix warning of select USB_OTG
USB: option: add XS Stick W100-2 from 4G Systems
xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices
usb: xhci: fix checking ep busy for CFC
xhci: Workaround to get Intel xHCI reset working more reliably
usb: chipidea: imx: fix a possible NULL dereference
usb: chipidea: usbmisc_imx: fix a possible NULL dereference
usb: chipidea: otg: gadget module load and unload support
usb: chipidea: debug: disable usb irq while role switch
ARM: dts: imx27.dtsi: change the clock information for usb
usb: chipidea: imx: refine clock operations to adapt for all platforms
usb: gadget: atmel_usba_udc: Expose correct device speed
usb: musb: enable usb_dma parameter
usb: phy: phy-mxs-usb: fix a possible NULL dereference
usb: dwc3: gadget: let us set lower max_speed
usb: musb: fix tx fifo flush handling
usb: gadget: f_loopback: fix the warning during the enumeration
usb: dwc2: host: Fix remote wakeup when not in DWC2_L2
...
projects / linux-beck.git / log