Arnd Bergmann [Fri, 28 Nov 2014 14:04:20 +0000 (15:04 +0100)]
Merge tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner simple frambuffer support" from Maxime Ripard:
This enables the simple framebuffer on all the supported Allwinner SoCs (but
the A80). That allows to have at last a video display usable by using the
framebuffer the firmware might have set up.
* tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (55 commits)
ARM: dts: sunxi: Update simplefb nodes so that u-boot can find them
ARM: dts: sunxi: Add de_be0 clk parent pll to simplefb node
ARM: dts: sun7i: Add simplefb node
ARM: dts: sun6i: Add simplefb node
ARM: dts: sun5i: Add simplefb node
ARM: dts: sun4i: Add simplefb node
ARM: dts: sun6i: Add ethernet support to M9 board
ARM: sun6i: DT: Add PLL6 multiple outputs
ARM: dts: sun6i: Add support for the status led
ARM: dts: sun6i: Add EHCI support for the M9 board
ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator
ARM: dts: sun7i: Cubietruck: add power supply regulator for USB OTG VBUS
ARM: dts: sun7i: Cubietruck: override regulator pin
ARM: sun7i: dtsi: add support for usbphy0
ARM: dtsi: sunxi: add common VBUS regulator
ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator
ARM: sun5i: olinuxino: Relicense the device tree under GPLv2/X11
ARM: sun4i: cubieboard: Relicense the device tree under GPLv2/X11
ARM: sun7i: pcduino3: Relicense the device tree under GPLv2/X11
ARM: sun4i: pcduino: Relicense the device tree under GPLv2/X11
...
Arnd Bergmann [Fri, 28 Nov 2014 14:01:57 +0000 (15:01 +0100)]
Merge tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "The i.MX device tree changes for 3.19" from Shawn Guo:
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
* tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits)
ARM: dts: imx6q-tbs2910: Enable snvs-poweroff
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
ARM: dts: vf-colibri: add USB regulators
ARM: dts: imx6: phyFLEX: Add CAN support
ARM: dts: imx6: phyFLEX: Add PCIe
ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic
ARM: dts: imx6: phyFLEX: Enable gpmi in module file
ARM: dts: imx6: phyFLEX: set nodes in alphabetical order
ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC
ARM: dts: vf-colibri: Add I2C support
ARM: dts: imx6qdl: Enable CODA960 VPU
ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property
ARM: dts: vf610: enable USB misc/phy nodes where necessary
ARM: dts: vf610: use new GPIO support
ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards
ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
ARM: dts: vf500-colibri: add Colibri VF50 support
ARM: dts: vf610: create generic base device trees
ARM: dts: vf610: assign oscillator to clock module
dt-bindings: arm: add Freescale LS1021A SoC device tree binding
...
Arnd Bergmann [Fri, 28 Nov 2014 11:36:43 +0000 (12:36 +0100)]
Merge tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "temporarily disable rk3288-smp" from Heiko Stuebner:
Disable smp again on rk3288 temporarily to make Olof's boottest
run again, until the patches for using the physical architected
timers got accepted.
* tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: temporarily disable smp on rk3288
Pankaj Dubey [Wed, 26 Nov 2014 18:24:45 +0000 (03:24 +0900)]
ARM: dts: add sysreg phandle to i2c device nodes for exynos
This patch adds syscon based phandle to i2c device nodes of exynos5250
and exynos5420. These phandles will be used to save restore i2c sysreg
configuration register during s2r from i2c driver.
CC: Rob Herring <robh+dt@kernel.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Russell King <linux@arm.linux.org.uk> CC: devicetree@vger.kernel.org CC: linux-doc@vger.kernel.org Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Youngjun Cho [Wed, 26 Nov 2014 17:43:39 +0000 (02:43 +0900)]
ARM: dts: add board dts file for Exynos3250-based Monk board
This patch adds new board dts file to support Samsung Monk board which
is based on Exynos3250 SoC and has different H/W configuration from
Rinato.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Youngjun Cho <yj44.cho@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The I2S controller can use the external clock as reference clock with
master mode. But based on different hardware or software design, this
external clock might be needed or not needed.
So the external input pin can be an independent pinctrl group, and the
card driver can decice to get it or not.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
Rongjun Ying [Tue, 25 Nov 2014 10:46:42 +0000 (18:46 +0800)]
ARM: dts: atlas6: add a separate pingroup for i2s mclk output
The I2S controller can output mclk to external audio codec. But by
hardware design, some codecs need mclk and some codecs do not need
mclk. So the mclk pin can be an independent pinctrl group, and the
card driver can get it or not based on boards.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
Roger Quadros [Wed, 29 Oct 2014 15:52:57 +0000 (17:52 +0200)]
ARM: dts: am335x-evm: Add DCAN1 details
DCAN1 is routed to CAN port (J11) when Profile 1 is selected on the
profile selection switch.
Provide information for DCAN1 pins and node but keep it disabled
by default. User has to manually enable it if Profile 1 is chosen.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 9 Sep 2014 13:15:35 +0000 (16:15 +0300)]
ARM: dts: am33xx: Update DCAN nodes
Add "raminit-syscon" property to specify the RAMINIT register.
Add clock information.
Rename can nodes from "d_can" to "can" to be compliant
with the ePAPR specs.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Fri, 18 Jul 2014 05:59:11 +0000 (11:29 +0530)]
ARM: dts: am437x-gp: Add dcan support
Add DCAN support for AM437x GP EVM with both DCAN instances.
[Roger Q] Updated output pin to not use pull up.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Hans de Goede [Tue, 18 Nov 2014 11:07:13 +0000 (12:07 +0100)]
ARM: dts: sunxi: Update simplefb nodes so that u-boot can find them
Review of the u-boot sunxi simplefb patches has led to the decision that
u-boot should not use a specific path to find the nodes as this goes contrary
to how devicetree usually works.
Instead a platform specific compatible + properties should be used for this.
The simplefb bindings have already been updated to reflect this, this patch
brings the sunxi devicetree files in line with the new binding, and the
actual u-boot implementation as it is going upstream.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Avoid the parent pll for the mod-clk for de_be0 getting disabled when non of
the other users are enabled (which can happen when none of i2c, spi and mmc
are in use).
Note for now we point directly to the parent rather then to the de_be0 mod-clk
as that is not modelled in our devicetree yet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 13 Nov 2014 09:31:48 +0000 (10:31 +0100)]
ARM: dts: sun6i: Add EHCI support for the M9 board
The Mele M9 / A1000G quad uses both usb-ports, one goes to an internal
usb wifi card, the other to a build-in usb-hub, so neither need their
OHCI companion controller to be enabled since the are always connected at
USB-2 speeds.
The controller which is attached to the wifi also does not need a vbus
regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 13 Nov 2014 09:31:43 +0000 (10:31 +0100)]
ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator
This avoids it getting briefly turned off between when the regulator getting
registered and the ahci driver turning it back on, thus avoiding the disk
going into emergency head park mode.
Reported-by: Bruno Prémont <bonbons@linux-vserver.org> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Karsten Merker [Tue, 11 Nov 2014 23:01:46 +0000 (00:01 +0100)]
ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator
On the LeMaker Banana Pi, probing the external ethernet PHY connected
to the SoC's internal GMAC module sometimes fails. The PHY power
supply is handled via a GPIO-controlled regulator, and the existing
regulator startup-delay of 50000us is too short to make sure that the
PHY is always fully powered up when it is queried by phylib. Tests
have shown that to provide a reliable PHY detection, the startup-delay
has to be increased to at least 60000us. To have a certain safety margin
and to cater for manufacturing variations between different boards,
the delay gets set to 100000us as discussed on the linux-arm-kernel
mailinglist.
Signed-off-by: Karsten Merker <merker@debian.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun5i: olinuxino: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Roman Byshko <rbyshko@gmail.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun4i: cubieboard: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: Emilio López <emilio@elopez.com.ar> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Olliver Schinagl <oliver@schinagl.nl> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Roman Byshko <rbyshko@gmail.com> Acked-by: Stefan Roese <sr@denx.de>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun4i: pcduino: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
Chen-Yu Tsai [Fri, 31 Oct 2014 03:05:49 +0000 (11:05 +0800)]
ARM: dts: sun9i: Add GPIO LEDs for A80 Optimus board
The A80 Optimus board has 3 usable LEDs that are controlled via GPIO.
This patch adds support for 2 of them which are driver by GPIOs in the
main pin controller. The remaining one uses GPIO from the R_PIO
controller, which we don't support yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun4i: a1000: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: Emilio López <emilio@elopez.com.ar> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Olliver Schinagl <oliver@schinagl.nl> Acked-by: Roman Byshko <rbyshko@gmail.com>
Maxime Ripard [Fri, 17 Oct 2014 09:38:23 +0000 (11:38 +0200)]
ARM: sunxi: Fix GPLv2 wording
During the GPL to GPL/X11 licensing migration, the GPL notice introduced
mentionned the device trees as a library, which is not really accurate. It
began to spread by copy and paste. Fix all these library mentions to reflect
the file that it's actually just a file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun7i: i12: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun5i: olinuxino micro: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Emilio López <emilio@elopez.com.ar> Acked-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun4i: olinuxino lime: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun4i: mini xplus: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun4i: inet97fv2: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch> Acked-by: Hans de Goede <hdegoede@redhat.com>
Maxime Ripard [Tue, 2 Sep 2014 17:25:26 +0000 (19:25 +0200)]
ARM: sun4i: hackberry: Relicense the device tree under GPLv2/X11
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Carlo Caione <carlo@caione.org> Acked-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Wed, 8 Oct 2014 13:02:54 +0000 (21:02 +0800)]
ARM: dts: sun9i: Add A80 Optimus Board support
The A80 Optimus Board is was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.
This board has a UART port, a JTAG connector, USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
This patch adds only basic support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Tested-by: Andreas Färber <afaerber@suse.de>
Hans de Goede [Wed, 1 Oct 2014 07:26:06 +0000 (09:26 +0200)]
ARM: dts: sun7i: Add Banana Pi board
The Banana Pi is an A20 based development board using Raspberry Pi compatible
IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi
and stereo audio out + various expenansion headers:
http://www.lemaker.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Robin Gong [Wed, 12 Nov 2014 08:20:37 +0000 (16:20 +0800)]
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
All chips of i.mx6 can be powered off by programming SNVS.
For example :
On i.mx6q-sabresd board, PMIC_ON_REQ connect with external
pmic ON/OFF pin, that will cause the whole PMIC powered off
except VSNVS. And system can restart once PMIC_ON_REQ goes
high by push POWRER key.
Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
projects / linux-beck.git / log