Add a "C5" cpuidle state to the SH7372 SoC connected to the A4S power
domain in such a way that A4S may be turned off by cpuidle if all
I/O devices in that domain have been suspended (or do not have
attached drivers).
This requires some reorganization of the initialization of SH7372
power management which affects the the boards based on it, Mackerel
and AP4EVB.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
PM / cpuidle: Make ladder governor use the "disabled" state flag
For the mechanism introduced by commit cbc9ef0 (PM / Domains: Add
preliminary support for cpuidle, v2) to work with the ladder
governor, that governor should respect the "disabled" state flag
added by that commit. Change the ladder governor accordingly.
Honor state disabling in the cpuidle ladder governor
There are two cpuidle governors ladder and menu. While the ladder
governor is always available, if CONFIG_CPU_IDLE is selected, the
menu governor additionally requires CONFIG_NO_HZ.
A particular C state can be disabled by writing to the sysfs file
/sys/devices/system/cpu/cpuN/cpuidle/stateN/disable, but this mechanism
is only implemented in the menu governor. Thus, in a system where
CONFIG_NO_HZ is not selected, the ladder governor becomes default and
always will walk through all sleep states - irrespective of whether the
C state was disabled via sysfs or not. The only way to select a specific
C state was to write the related latency to /dev/cpu_dma_latency and
keep the file open as long as this setting was required - not very
practical and not suitable for setting a single core in an SMP system.
With this patch, the ladder governor only will promote to the next
C state, if it has not been disabled, and it will demote, if the
current C state was disabled.
Note that the patch does not make the setting of the sysfs variable
"disable" coherent, i.e. if one is disabling a light state, then all
deeper states are disabled as well, but the "disable" variable does not
reflect it. Likewise, if one enables a deep state but a lighter state
still is disabled, then this has no effect. A related section has been
added to the documentation.
Signed-off-by: Carsten Emde <C.Emde@osadl.org> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ARM: shmobile: Make sh7372 cpuidle handling more straightforward
The sh7372 cpuidle code uses the same artificially designed routine
shmobile_cpuidle_enter() as the .enter() callback for all of its
cpuidle states. However, shmobile_cpuidle_enter() calls a different
"enter" function for each state using an array of function pointers
populated by the sh7372 PM initialization code. Moreover, the
states[] array of the shmobile cpuidle driver is populated by that
code as well, although in principle it just might have been filled
with static data.
All of that complexity goes away if the sh7372 cpuidle code is
allowed to define its own cpuidle driver structure that can be passed
for registration to the common shmobile cpuidle initialization
routine, so modify the code accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Move definition of shmobile_init_late() to header
The role of the only function in the common.c file in
arch/arm/mach-shmobile, shmobile_init_late(), is to call two
initializers whose definitions depend on kernel configuration
options. Those initializers may very well be called from a static
inline function in arm/mach-shmobile/include/mach/common.h,
though, in which makes the code a bit easier to read. Moreover,
the common.c may be dropped entirely then.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Remove the console check from sh7372_enter_suspend()
The !console_suspend_enabled check in sh7372_enter_suspend() seems
to be reversed and the condition it is supposed to catch (console
clock enabled) should be detected by the sh7372_sysc_valid() check
anyway, so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Rework adding devices to PM domains on AP4EVB
Use the function rmobile_add_devices_to_domains() introduced
previously for adding devices to PM domains during the AP4EVB
initialization instead of a series of rmobile_add_device_to_domain*()
calls. This also causes the default device PM QoS latencies to be
used on that board in analogy with Mackerel.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Rework adding devices to PM domains on Mackerel
On SH7372 and Mackerel devices are added to PM domains through a
series of rmobile_add_device_to_domain_td() calls where the last
argument is always the same. This is quite inefficient, so add
a common function for adding devices to PM domains that reads the
domain-device pairs information from a table and use it during SH7372
and Mackerel initialization.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Specify device latencies for Mackerel devices directly
The results of adaptive latency computations in
GENPD_DEV_TIMED_CALLBACK() show that the start/stop and save/restore
state latencies of all devices on the Mackerel board I have tried are
a little below 250 us. Therefore, if the 250 us is used as the
common initial value of the latency fields in struct gpd_timing_data
for all devices on Mackerel, the latency values will never have to
change at run time and there won't be any overhead related to
re-computation of the corresponding PM QoS data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Specify device latencies for SH7372 devices directly
The results of adaptive latency computations in
GENPD_DEV_TIMED_CALLBACK() show that the start/stop and save/restore
state latencies of all devices on SH7372 I have tried are a little
below 250 us. Therefore, if the 250 us is used as the common initial
value of the latency fields in struct gpd_timing_data for all devices
on SH7372, the latency values will never have to change at run time
and there won't be any overhead related to re-computation of the
corresponding PM QoS data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Allow device latencies to be specified directly
Make it possible to specify device start/stop and save/restore
state latencies directy when adding devices to PM domains. For
this purpose, introduce rmobile_add_device_to_domain_td() whose
third argument is a pointer to a struct gpd_timing_data object
containing device latency data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Set PM domain on/off latencies directly
The results of adaptive latency computations in __pm_genpd_poweron()
and pm_genpd_poweroff() show that the power on/power off latencies
of all power domains in SH7372 are a little below 250 us. Therefore,
if 250 us is used as the common initial value of the latency fields
in struct generic_pm_domain for all domains, the latency values
will never have to change at run time and there won't be any overhead
related to re-computation of the corresponding PM QoS data.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Make rmobile_init_pm_domain() static
Since rmobile_init_pm_domain() is not called anywhere outside of
arch/arm/mach-shmobile/pm-rmobile.c any more, it can be made static
and its header may be removed from pm-rmobile.h. Modify the code
accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Move r8a7740's PM domain objects to a table
Instead of giving a name to every r8a7740's PM domain object, put
them all into a table and use rmobile_init_domains(), introduced by a
previous patch, for initializing them all altogether. Also, use
pm_genpd_add_subdomain_names() for adding A3SP as a subdomain of A4S.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Move sh7372's PM domain objects to a table
Instead of giving a name to every sh7372's PM domain object, put them
all into a table and use rmobile_init_domains(), introduced by a
previous patch, for initializing them all altogether. Also, use
pm_genpd_add_subdomain_names() for adding subdomains to the PM
domains and pm_genpd_poweron_name() for turning on the A4S domain
when preparing for system suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Do not access sh7372 A4S domain internals directly
The sh7372_enter_suspend() routine checks the status field of the
generic PM domain object corresponding to the A4S domain in order to
check if it can turn that domain off when entering system sleep.
However, it shouldn't rely on the specific values of the generic
data structures this way, so make it use its own mechanism to
recognize when it is safe to turn that domain off.
For this purpos, introduce a boolean variable a4s_suspend_ready
that will be set by the A4S' suspend routine and unset by its
resume routine executed by rmobile_pd_power_down() and
__rmobile_pd_power_up(), respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Use domain names when adding subdomains to power domains
Make the power management code under arch/arm/mach-shmobile/
use pm_genpd_add_subdomain_names() for adding subdomains to power
domains, which makes it possible to drop
rmobile_pm_add_subdomain() and will allow us to carry out those
operations for domain objects stored in tables in a straightforward
way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Drop r8a7779_add_device_to_domain()
If the r8a7779's PM domains are given names, this SoC and its boards
will be able to use rmobile_add_device_to_domain() for adding devices
to those domains and r8a7779_add_device_to_domain(), which is not
used anywhere at the moment anyway, may be dopped.
Accordingly, give names to the r8a7779's PM domains and drop
r8a7779_add_device_to_domain().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
ARM: shmobile: Use names of power domains for adding devices to them
Make the power management code under arch/arm/mach-shmobile/ use
names of power domains instead of pointers to domain objects for
adding devices to the domains. This will allow us to put the
domain objects into tables and register them all in one shot
going forward.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
PM / Domains: Operations related to cpuidle using domain names
Make it possible to use domain names in operations connecting cpuidle
to and disconnecting it from a PM domain. This is useful on
platforms where PM domain objects are organized in such a way that
the names of the domains are easier to use than the addresses of
those objects.
PM / Domains: Document cpuidle-related functions and change their names
The names of the cpuidle-related functions in
drivers/base/power/domain.c are inconsistent with the names of the
other exported functions in that file (the "pm_" prefix is missing
from them) and they are missing kerneldoc comments.
Fix that by adding the missing "pm_" prefix to the names of those
functions and add kerneldoc comments documenting them.
PM / Domains: Add power-on function using names to identify domains
It sometimes is necessary to turn on a given PM domain when only
the name of it is known and the domain pointer is not readily
available. For this reason, add a new helper function,
pm_genpd_name_poweron(), allowing the caller to turn on a PM domain
using its name for identification. To avoid code duplication,
move the domain lookup code to a separate function.
PM / Domains: Make it possible to use names when adding subdomains
Add a new helper function, pm_genpd_add_subdomain_names(), allowing
the caller to add a subdomain to a generic PM domain using names for
domain identification (both domains have to be initialized before).
This function is useful for adding subdomains to PM domains whose
representations are stored in tables, when the caller doesn't know
the indices of the domain to add the subdomain to and of the
subdomain itself, but it knows the domains' names.
PM / Domains: Make it possible to use domain names when adding devices
Add a new helper function __pm_genpd_name_add_device() allowing
a device to be added to a (registered) generic PM domain identified
by name. Add a wrapper around it, pm_genpd_name_add_device(),
passing NULL as the last argument and reorganize pm_domains.h for the
new functions to be defined consistently with the existing ones.
These functions are useful for adding devices to PM domains whose
representations are stored in tables, when the caller doesn't know
the index of the domain to add the device to, but it knows the
domain's name.
The syscore device PM flag used to mark the devices (belonging to
PM domains) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages, need not be
accessed by the runtime PM core functions, because all of the devices
it is set for need to be marked as "irq safe" anyway and are
protected from being turned off by runtime PM by ensuring that their
usage counters are always set.
For this reason, make the syscore flag system-wide PM-specific
and simplify the code used for manipulating it, because it need not
acquire the device's power.lock any more.
Modify the SH MTU2 clock event device driver to support runtime PM at
a basic level (i.e. device clocks can be disabled and enabled, but
domain power must be on, because the device has to be marked as
"irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
Modify the SH CMT clock source/clock event device driver to support
runtime PM at a basic level (i.e. device clocks can be disabled and
enabled, but domain power must be on, because the devices have to
be marked as "irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
Modify the SH TMU clock source/clock event device driver to support
runtime PM at a basic level (i.e. device clocks can be disabled and
enabled, but domain power must be on, because the devices have to
be marked as "irq safe").
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
PM / Domains: Do not measure start time for "irq safe" devices
The genpd_start_dev() routine used by pm_genpd_runtime_resume()
to put "irq safe" devices into the full power state measures the
time necessary to "start" the device and updates its PM QoS timing
data if necessary. This may lead to a deadlock if the given device
is a clock source and genpd_start_dev() is invoked from within the
clock source's .enable() routine, which will happen if that routine
uses pm_runtime_get_sync(), for example, to ensure that the device
is operational.
For this reason, introduce a special routine analogous to
genpd_start_dev(), called genpd_start_dev_no_timing(), that doesn't
carry out the time measurement, and make pm_genpd_runtime_resume()
use it instead of genpd_start_dev() to power up "irq safe" devices.
PM / Domains: Move syscore flag from subsys data to struct device
The syscore device PM flag is used to mark the devices (belonging to
a PM domain) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages. That flag is
stored in the device's struct pm_subsys_data object whose address is
available from struct device. However, in some situations it may be
convenient to set that flag before the device is added to a PM
domain, so it is better to move it directly to the "power" member of
struct device. Then, it can be checked by the routines in
drivers/base/power/runtime.c and drivers/base/power/main.c, which is
more straightforward.
This also reduces the number of dev_gpd_data() invocations in the
generic PM domains framework, so the overhead related to the syscore
flag is slightly smaller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
PM / Domains: Rename the always_on device flag to syscore
The always_on device flag is used to mark the devices (belonging to
a PM domain) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages. Change name
of that flag to "syscore" to better reflect its purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
PM / Runtime: Allow helpers to be called by early platform drivers
Runtime PM helper functions, like pm_runtime_get_sync(), cannot be
called by early platform device drivers, because the devices' power
management locks are not initialized at that time. This is quite
inconvenient, so modify early_platform_add_devices() to initialize
the devices power management locks as appropriate and make sure that
they won't be initialized more than once if an early platform
device is going to be used as a regular one later.
Make the device power management initialization more straightforward
by moving the initialization of common (i.e. used by both runtime PM
and system suspend) fields to a separate routine.
Introduce suspend/resume routines for SH MTU2 clock event devices
such that if those devices belong to a PM domain, the generic PM
domains framework will be notified that the given domain may be
turned off (during system suspend) or that it has to be turned on
(during system resume).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
Introduce suspend/resume routines for SH CMT clock event devices and
modify the suspend/resume routines for SH CMT clock sources such that
if those devices belong to a PM domain, the generic PM domains
framework will be notified that the given domain may be turned off
(during system suspend) or that it has to be turned on (during system
resume).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
Introduce suspend/resume routines for SH TMU clock source and
clock event device such that if those devices belong to a PM domain,
the generic PM domains framework will be notified that the given
domain may be turned off (during system suspend) or that it has to
be turned on (during system resume).
This change allows the A4R domain on SH7372 to be turned off during
system suspend (tested on the Mackerel board) if the TMU clock source
and/or clock event device is in use.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Magnus Damm <damm@opensource.se>
timekeeping: Add suspend and resume of clock event devices
Some clock event devices, for example such that belong to PM domains,
need to be handled in a spcial way during the timekeeping suspend
and resume (which takes place in the system core, or "syscore",
stages of system power transitions) in analogy with clock sources.
Introduce .suspend() and .resume() callbacks for clock event devices
that will be executed by timekeeping_suspend/_resume(), respectively,
next the the clock sources' .suspend() and .resume() callbacks.
PM / Domains: Add power off/on function for system core suspend stage
Introduce function pm_genpd_syscore_switch() and two wrappers around
it, pm_genpd_syscore_poweroff() and pm_genpd_syscore_poweron(),
allowing the callers to let the generic PM domains framework know
that the given device is not necessary any more and its PM domain
can be turned off (the former) or that the given device will be
required immediately, so its PM domain has to be turned on (the
latter) during the system core (syscore) stage of system suspend
(or hibernation) and resume.
These functions will be used for handling devices registered as
clock sources and clock event devices that belong to PM domains.
PM / Domains: Introduce simplified power on routine for system resume
Introduce function pm_genpd_sync_poweron() for restoring domain power
during resume from system suspend and hibernation. It can be much
simpler than pm_genpd_poweron(), because it doesn't have to care
about locking and it can skip many checks done by the latter.
Modify pm_genpd_resume_noirq() and pm_genpd_restore_noirq() to use
the new function.
Ian Kent [Mon, 6 Aug 2012 01:37:47 +0000 (09:37 +0800)]
autofs4 - fix get_next_positive_subdir()
Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.
The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 16 Aug 2012 18:47:42 +0000 (11:47 -0700)]
Merge tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"Just a trivial patch to include vfio.h in the installed headers so we
can complete userspace integration into QEMU."
* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio: Include vfio.h in installed headers
Linus Torvalds [Thu, 16 Aug 2012 18:31:59 +0000 (11:31 -0700)]
Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
Linus Torvalds [Thu, 16 Aug 2012 18:13:16 +0000 (11:13 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull two slave-dmaengine fixes from Vinod Koul:
"One fixes the correct use of clock API in imx driver and the other
enables clock for tegra driver, which is used for other tegra driver
conversion to dmanegine in -next."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: enable/disable dma clock
dma: imx-dma: Fix kernel crash due to missing clock conversion
Linus Torvalds [Thu, 16 Aug 2012 18:08:32 +0000 (11:08 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Just some intel and nouveau ones this time, intel has more edp panel
fixes for macbooks and nouveau has a suspend/resume regression fix in
there."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
drm/nve0/fifo: add support for the flip completion swmthd
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
Dave Airlie [Wed, 15 Aug 2012 10:31:22 +0000 (20:31 +1000)]
Merge branch 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
Dave Airlie [Wed, 15 Aug 2012 10:27:51 +0000 (20:27 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
David S. Miller [Wed, 15 Aug 2012 07:37:29 +0000 (00:37 -0700)]
sparc64: Be less verbose during vmemmap population.
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit c2b91e2eec9678dbda274e906cc32ea8f711da3b
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322 Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671 Tested-by: Roberto Romer <sildurin@gmail.com> Tested-by: Daniel Wagner <wagi@monom.org> Tested-by: Keith Packard <keithp@keithp.com> Cc: stable@vger.kernel.org Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Tue, 14 Aug 2012 04:58:59 +0000 (07:58 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
Linus Torvalds [Tue, 14 Aug 2012 04:52:41 +0000 (07:52 +0300)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and intel fixes mostly, one fix to the mgag200 driver to not
hang on certain server variants."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
drm/mgag200: fix G200ER pll picking algorithm
drm/edid: Fix potential memory leak in edid_load()
drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
...
Arnd Bergmann [Mon, 13 Aug 2012 14:36:10 +0000 (14:36 +0000)]
GPIO: gpio-pxa: fix building without CONFIG_OF
Commit 7212157267 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:
drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)
Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Ben Skeggs [Fri, 27 Jul 2012 04:18:03 +0000 (14:18 +1000)]
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
At least partially fixes DP output detection on W530. Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).
Dave Airlie [Mon, 13 Aug 2012 23:25:01 +0000 (09:25 +1000)]
Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex Deucher writes:
This is the current set of radeon fixes for 3.6. Nothing too major.
Highlights:
- various display fixes
- some SI fixes
- new SI pci ids
- major VM fix
- CS checker support for MSAA
I've tested on a number of cards across generations and noticed no problems.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
Jani Nikula [Mon, 13 Aug 2012 14:33:02 +0000 (17:33 +0300)]
drm/i915: ensure i2c adapter is all set before adding it
i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().
LKML-Reference: <5021F00B.7000503@ionic.de> Tested-by: Mihai Moldovan <ionic@ionic.de> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jerome Glisse [Mon, 6 Aug 2012 16:32:21 +0000 (12:32 -0400)]
drm/radeon: fence virtual address and free it once idle v4
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
drm/radeon: do not reenable crtc after moving vram start address
It seems we can not update the crtc scanout address. After disabling
crtc, update to base address do not take effect after crtc being
reenable leading to at least frame being scanout from the old crtc
base address. Disabling crtc display request lead to same behavior.
So after changing the vram address if we don't keep crtc disabled
we will have the GPU trying to read some random system memory address
with some iommu this will broke the crtc engine and will lead to
broken display and iommu error message.
So to avoid this, disable crtc. For flicker less boot we will need
to avoid moving the vram start address.
Alex Deucher [Thu, 26 Jul 2012 17:38:52 +0000 (13:38 -0400)]
drm/radeon: properly handle crtc powergating
Need to make sure the crtc is gated on before modesetting.
Explicitly gate the crtc on in prepare() and set a flag
so that the dpms functions don't gate it off during
mode set.
Noticed by sylware on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Arnd Bergmann [Wed, 8 Aug 2012 21:27:58 +0000 (05:27 +0800)]
leds: renesas: fix error handling
bfe4c041 "leds: convert Renesas TPU LED driver to devm_kzalloc() and
cleanup error exit path" introduced a possible case in which r_tpu_probe
calls iounmap on a wild pointer. This changes the one case that was
missed in the same way as the other error paths.
Without this patch, building kota2_defconfig results in:
drivers/leds/leds-renesas-tpu.c: In function 'r_tpu_probe':
drivers/leds/leds-renesas-tpu.c:246:6: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-renesas-tpu.c:308:17: warning: 'p' may be used uninitialized in this function [-Wuninitialized]
Pull networking changes from David Miller:
"Most importantly this should cure the ipv4-mapped ipv6 socket TCP
crashes some people were seeing, otherwise:
1) Fix e1000e autonegotiation handling regression, from Tushar Dave.
2) Fix TX data corruption race on e1000e down, also from Tushar Dave.
3) Fix bfin_sir IRDA driver build, from Sonic Zhang.
4) AF_PACKET mmap() tests a flag in the TX ring shared between
userspace and the kernel for an internal consistency check. It
really shouldn't do this to validate the kernel's own behavior
because the user can corrupt it to be any value at all. From
Daniel Borkmann.
5) Fix TCP metrics leak on netns dismantle, from Eric Dumazet.
6) Orphan the anonymous TCP socket from the SKB in
ip_send_unicast_reply() so that the rest of the stack needn't see
it. Otherwise we get selinux problems of all sorts, from Eric
Dumazet.
This is the best way to fix this since the socket is just a place
holder for sending packets in a context where we have no real
socket at all.
7) Fix TUN detach crashes, from Stanislav Kinsbursky.
8) dev_set_alias() leaks memory on krealloc() failure, from Alexey
Khoroshilov.
9) FIB trie must use call_rcu() not call_rcu_bh(), because this code
is not universally invoked from software interrupts. From Eric
Dumazet.
10) PPTP looks up ipv4 routes with the wrong network namespace, fix
from Gao Feng."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
bnx2x: Fix compiler warnings
af_packet: remove BUG statement in tpacket_destruct_skb
macvtap: rcu_dereference outside read-lock section
codel: refine one condition to avoid a nul rec_inv_sqrt
ixgbe: add missing braces
ipv4: fix ip_send_skb()
net: tcp: ipv6_mapped needs sk_rx_dst_set method
ipv4: tcp: unicast_sock should not land outside of TCP stack
bnx2x: Fix recovery flow cleanup during probe
bnx2x: fix unload previous driver flow when flr-capable
tun: don't zeroize sock->file on detach
igb: Fix register defines for all non-82575 hardware
e1000e: fix panic while dumping packets on Tx hang with IOMMU
igb: fix panic while dumping packets on Tx hang with IOMMU
tcp: must free metrics at net dismantle
net/stmmac: mark probe function as __devinit
lpc_eth: remove obsolete ifdefs
net/core: Fix potential memory leak in dev_set_alias()
cdc-phonet: Don't leak in usbpn_open
batman-adv: Fix mem leak in the batadv_tt_local_event() function
...
Linus Torvalds [Mon, 13 Aug 2012 05:40:51 +0000 (08:40 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull tcm_vhost level target fabric driver from Nicholas Bellinger:
"Here is the PULL request for the initial merge of tcm_vhost based on
RFC-v5 code with MST's ACK appended to the initial merge commit."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_vhost: Initial merge for vhost level target fabric driver
Joren Van Onder [Sat, 11 Aug 2012 17:10:35 +0000 (17:10 +0000)]
bnx2x: Fix compiler warnings
Fix the following compiler warnings:
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:2908:3: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:1709:7: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: Joren Van Onder <joren.vanonder@gmail.com> Acked-By: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_packet: remove BUG statement in tpacket_destruct_skb
Here's a quote of the comment about the BUG macro from asm-generic/bug.h:
Don't use BUG() or BUG_ON() unless there's really no way out; one
example might be detecting data structure corruption in the middle
of an operation that can't be backed out of. If the (sub)system
can somehow continue operating, perhaps with reduced functionality,
it's probably not BUG-worthy.
If you're tempted to BUG(), think again: is completely giving up
really the *only* solution? There are usually better options, where
users don't need to reboot ASAP and can mostly shut down cleanly.
In our case, the status flag of a ring buffer slot is managed from both sides,
the kernel space and the user space. This means that even though the kernel
side might work as expected, the user space screws up and changes this flag
right between the send(2) is triggered when the flag is changed to
TP_STATUS_SENDING and a given skb is destructed after some time. Then, this
will hit the BUG macro. As David suggested, the best solution is to simply
remove this statement since it cannot be used for kernel side internal
consistency checks. I've tested it and the system still behaves /stable/ in
this case, so in accordance with the above comment, we should rather remove it.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_dereference occurs in update section. Replacement by
rcu_dereference_protected in order to prevent lockdep
complaint.
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 12 Aug 2012 18:45:33 +0000 (21:45 +0300)]
Merge tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
* tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers/gpio/gpio-langwell.c: fix error return code
gpio: samsung: Fix off-by-one bug in gpio addresses
ARM: dts: imx: add alias for gpio
gpio/mxc: specify gpio base for device tree probe
gpio/mxc: remove redundant shadow variables initialization
GPIO: gpio-pxa: fix devicetree functions
gpio: msic: Fix calculating register address in msic_gpio_to_oreg()
gpio-sch: Fix leak of resource
Linus Torvalds [Sun, 12 Aug 2012 18:34:09 +0000 (21:34 +0300)]
Merge tag 'pm-for-3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
- Fix for two recent regressions in the generic PM domains framework.
- Revert of a commit that introduced a resume regression and is
conceptually incorrect in my opinion.
- Fix for a return value in pcc-cpufreq.c from Julia Lawall.
- RTC wakeup signaling fix from Neil Brown.
- Suppression of compiler warnings for CONFIG_PM_SLEEP unset in ACPI,
platform/x86 and TPM drivers.
* tag 'pm-for-3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tpm_tis / PM: Fix unused function warning for CONFIG_PM_SLEEP
platform / x86 / PM: Fix unused function warnings for CONFIG_PM_SLEEP
ACPI / PM: Fix unused function warnings for CONFIG_PM_SLEEP
Revert "NMI watchdog: fix for lockup detector breakage on resume"
PM: Make dev_pm_get_subsys_data() always return 0 on success
drivers/cpufreq/pcc-cpufreq.c: fix error return code
RTC: Avoid races between RTC alarm wakeup and suspend.
Linus Torvalds [Sun, 12 Aug 2012 18:31:44 +0000 (21:31 +0300)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Arnd Bergmann:
"These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file.
The largest part of the fixes are patches that address bugs found by
building all the ARM defconfig files. There are a lot more warnings
that we have patches for, but the others are either still under
discussion or are harmless and do not cause actual problems besides
making the build slightly noisy."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: davinci: remove broken ntosd2_init_i2c
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
ARM: imx: gpmi-nand depends on mxs-dma
ARM: integrator: include <linux/export.h>
ARM: s3c24xx: use new PWM driver
ARM: sa1100: include linux/io.h in hackkit leds code
Input: eeti_ts: pass gpio value instead of IRQ
ARM: pxa: remove irq_to_gpio from ezx-pcap driver
ARM: tegra: more regulator fixes for Harmony
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
ARM: kirkwood: fix typo in Makefile.boot
i.MX27: Fix emma-prp and csi clocks.
ARM: integrator: use clk_prepare_enable() for timer
MAINTAINERS: update entry for Linus Walleij
...
Jeff Mahoney [Fri, 10 Aug 2012 19:07:09 +0000 (15:07 -0400)]
printk: Fix calculation of length used to discard records
While tracking down a weird buffer overflow issue in a program that
looked to be sane, I started double checking the length returned by
syslog(SYSLOG_ACTION_READ_ALL, ...) to make sure it wasn't overflowing
the buffer.
It turns out that the loops that calculate how much space the entries
will take when they're copied don't include the newlines and prefixes
that will be included in the final output since prev flags is passed as
zero.
This patch properly accounts for it and fixes the overflow.
CC: stable@kernel.org Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>