The logic at em28xx_isoc_dvb_max_packetsize() sucks, at least for newer
the needed packet size. Yet, it is better than nothing.
Rewrite the code in order to change the default to 752 for em2884 and
newer chips and provide a better way to handle per-chipset specifics.
For em2874, the current default should be enough, as the only em2874
board is currently a 1-seg ISDB-T board, so, it needs only a limited
amount of bandwidth.
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
Currently, the driver assumes that all QAM carriers are spaced with
8MHz. This is wrong, and may decrease QoS on Countries like Brazil,
that have DVB-C carriers with 6MHz-spaced.
Fortunately, both ITU-T J-83 and EN 300 429 specifies a way to
associate the symbol rate with the bandwidth needed for it.
For ITU-T J-83 2007 annex A, the maximum symbol rate for 6 MHz is:
6 MHz / 1.15 = 5217391 Bauds
For ITU-T J-83 2007 annex C, the maximum symbol rate for 6 MHz is:
6 MHz / 1.13 = 5309735 Bauds.
As this tuner is currently used only for DRX-K, and it is currently
hard-coded to annex A, I've opted to use the roll-off factor of 0.15,
instead of 0.13.
If we ever support annex C, the better would be to add a DVB S2API
call to allow changing between Annex A and C, and add the 0.13 roll-off
factor to it.
This code is currently being used on other frontends, so I think we
should later add a core function with this code, to warrant that
it will be properly implemented everywhere.
Jean Delvare [Sun, 24 Jul 2011 18:36:15 +0000 (20:36 +0200)]
hwmon: (lm90) Make SA56004 detection more robust
With a device ID register value of 0, the SA56004 detection is rather
weak. Check several other register too to confirm the detection, as we
do for other supported devices.
Jean Delvare [Thu, 28 Jul 2011 06:22:25 +0000 (23:22 -0700)]
hwmon: (lm90) Simplify handling of extended local temp register
The optional extended local temperature register can never have
address 0, as this address is already used by another register. Thus
we can get rid of flag LM90_HAVE_LOCAL_EXT and simply rely on
reg_local_ext being non-zero to determine if a given chip has this
extension or not. This makes the code more simple.
Most PMBus devices provide manufacturer specific commands to read low and/or
high peak values for some or all of its sensors.
To support providing those values as lowest/highest attributes to the user,
introduce virtual PMBus commands. Those commands reside outside the normal
command set and have to be implemented in device specific code, which map the
virtual commands to device specific commands.
hwmon: (pmbus) Strengthen check for status register existence
With virtual register page support, it is now possible that the status register
on virtual pages does not exist or is itself virtual. To take this into account
when creating alarm attributes, generate those attributes only if the status
register on the respective page is known to exist.
Some PMBus chips have non-standard sensor registers. An easy way to
support such sensors is to introduce virtual pages and map the non-standard
registers into standard registers on an extra page.
For this to work, the code verifying if the configured number of pages exists
has to be removed. Since a wrong number of pages can only be configured in a
front-end driver, this should not have a practical impact since the resulting
errors should be found during development and testing.
Also, functions to read the chip status while checking if a command register
exists must be modified to no longer set the page register before reading the
status, since the physical page associated with the checked register may not
exist. This does not make a functional difference since the page was already set
when the attempt to read the register was made.
hwmon: (pmbus) Support reading and writing of word registers in device specific code
Some PMBus devices use non-standard registers for some of the sensors and/or
limits. To support such devices, add code to support reading and writing of word
size registers in device specific code.
Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Guenter Roeck [Sat, 25 Jun 2011 18:21:49 +0000 (11:21 -0700)]
hwmon: (pmbus) Add support for VID output voltage mode
In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.
This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Jeff Layton [Thu, 28 Jul 2011 16:48:26 +0000 (12:48 -0400)]
cifs: fix compiler warning in CIFSSMBQAllEAs
The recent fix to the above function causes this compiler warning to pop
on some gcc versions:
CC [M] fs/cifs/cifssmb.o
fs/cifs/cifssmb.c: In function ‘CIFSSMBQAllEAs’:
fs/cifs/cifssmb.c:5708: warning: ‘ea_name_len’ may be used uninitialized in
this function
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
CC arch/mips/pmc-sierra/msp71xx/msp_irq.o
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:112:2: error: request for member ‘flags’ in something not a structure or union
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:118:2: error: request for member ‘flags’ in something not a structure or union
make[4]: *** [arch/mips/pmc-sierra/msp71xx/msp_irq.o] Error 1
do_signal() does __put_user() which can fault, resulting in a
might_sleep() warning in down_read(&mm->mmap_sem) and a "scheduling
while atomic" warning when mmap_sem is contented. On swarm this also
results in:
WARNING: at kernel/smp.c:459 smp_call_function_many+0x148/0x398()
Modules linked in:
Call Trace:
Enable interrupts in do_notify_resume before delivering signals.
[ralf@linux-mips.org: Reported and original fix by tglx but I wanted to
minimize the amount of code being run with interrupts disabled so I moved
the local_irq_disable() call right into do_notify_resume. Which is saner
than doing it in entry.S.]
Reported-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: Loongson: Mark cascade interrupts IRQF_NO_THREAD
There are two cascade interrupts in Loongson machines, one for bonito
northbridge, another for the 8259A controller in the southbridge. Both
want to be non threaded.
MIPS: Mark cascade and low level interrupts IRQF_NO_THREAD
Mark interrupts with no_action handler, cascade interrupts, low level
interrupts (bus error, halt ..) with IRQF_NO_THREAD to exclude them
from forced threading.
Thomas Gleixner [Thu, 28 Jul 2011 15:21:43 +0000 (16:21 +0100)]
MIPS: ftrace: Fix the CONFIG_DYNAMIC_FTRACE=n compile
arch/mips/kernel/ftrace.c: In function ‘ftrace_get_parent_ra_addr’:
arch/mips/kernel/ftrace.c:212: error: implicit declaration of function ‘in_kernel_space’
arch/mips/kernel/ftrace.c: In function ‘prepare_ftrace_return’:
arch/mips/kernel/ftrace.c:314: error: ‘MCOUNT_OFFSET_INSNS’ undeclared (first use in this function)
arch/mips/kernel/ftrace.c:314: error: (Each undeclared identifier is reported only once
arch/mips/kernel/ftrace.c:314: error: for each function it appears in.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2634/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pci/pci-rc32434.c: In function 'rc32434_pci_init':
arch/mips/pci/pci-rc32434.c:217:16: error: 'rcrc32434_res_pci_io1' undeclared (first use in this function)
arch/mips/pci/pci-rc32434.c:217:16: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-rc32434.o] Error 1
Turns out this patch is producing many build errors with gcc 4.2. Based
on further testing with a test case extracted from the build errors found
further build errors and suboptimal generation even in violation of the
"R" constraint.
To make matters worse, the binutils changes also don't work quite as
intended so revert this patch for now.
MIPS: cache: Provide cache flush operations for XFS
Until now flush_kernel_vmap_range() and invalidate_kernel_vmap_range() did
not exist on MIPS resulting in heavy cache corruption on XFS filesystems.
Left for the post-3.0 time: optimization and make this work with highmem,
too. Since the combination of highmem + cache aliases atm doesn't work
this isn't a regression.
MIPS: SNI: Fix conflicting wrapper symbols for headers.
If Open Firmware / Device Tree support is enabled on a SNI RM kernel both
<asm/mipsprom.h> and <asm/prom.h> will be included into some .c files.
Since both headers use the same wrapper symbol only the inclusion of the
first file will have an effect but the 2nd file will be ignored resulting
in a build error.
After the recent cleanup of the register_*_smp_ops() functions msp71xx
wasn't fixed to include the now necessary header resulting in:
/home/ralf/src/linux/upstream-linus/arch/mips/pmc-sierra/msp71xx/msp_setup.c: In function ‘prom_init’:
/home/ralf/src/linux/upstream-linus/arch/mips/pmc-sierra/msp71xx/msp_setup.c:231:2: error: implicit declaration of function ‘register_vsmp_smp_ops’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
Triggered by pnx8550-jbs_defconfig and pnx8550-stb810_defconfig:
WARNING: vmlinux.o(.text+0xc0c): Section mismatch in reference from the function prom_getcmdline() to the variable .init.data:arcs_cmdline
The function prom_getcmdline() references
the variable __initdata arcs_cmdline.
This is often because prom_getcmdline lacks a __initdata
annotation or the annotation of arcs_cmdline is wrong.
WARNING: vmlinux.o(.text+0x3059f8): Section mismatch in reference from the function pcibios_plat_dev_init() to the function .devinit.text:request_bridge_irq()
The function pcibios_plat_dev_init() references
the function __devinit request_bridge_irq().
This is often because pcibios_plat_dev_init lacks a __devinit
annotation or the annotation of request_bridge_irq is wrong.
Fixing this one leads to:
WARNING: vmlinux.o(.text+0x1790): Section mismatch in reference from the function request_bridge_irq() to the function .devinit.text:register_bridge_irq()
The function request_bridge_irq() references
the function __devinit register_bridge_irq().
This is often because request_bridge_irq lacks a __devinit
annotation or the annotation of register_bridge_irq is wrong.
Jayachandran C [Tue, 21 Jun 2011 20:06:33 +0000 (01:36 +0530)]
MIPS: Netlogic: Specify architecture CFLAGS
Use -march=xlr if available, otherwise fallback to mips64. This allows
us to support compilation with MIPS toolchains which are not customized
for XLR.
[ralf@linux-mips.org: And more importantly it works around a gas bug in
binutils 2.21 which otherwise may result in an assertion failure building
arch/mips/kernel/genex.S. See
http://sourceware.org/bugzilla/show_bug.cgi?id=12915 for details.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2534/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
n2_crypto: Attach on Niagara-T3.
n2rng: Attach on Niagara-T3.
sparc: Detect and handle UltraSPARC-T3 cpu types.
sparc: Don't do expensive hypervisor PCR write unless necessary.
sparc: Add T3 sun4v cpu type and hypervisor group defines.
sparc: Don't leave sparc_pmu_type NULL on sun4v.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9aa31720b72e2bc2d665e24e1653c3e
gro: Only reset frag0 when skb can be pulled
...
Jeff Layton [Tue, 26 Jul 2011 22:23:47 +0000 (18:23 -0400)]
cifs: fix name parsing in CIFSSMBQAllEAs
cifs: fix name parsing in CIFSSMBQAllEAs
The code that matches EA names in CIFSSMBQAllEAs is incorrect. It
uses strncmp to do the comparison with the length limited to the
name_len sent in the response.
Problem: Suppose we're looking for an attribute named "foobar" and
have an attribute before it in the EA list named "foo". The
comparison will succeed since we're only looking at the first 3
characters. Fix this by also comparing the length of the provided
ea_name with the name_len in the response. If they're not equal then
it shouldn't match.
Reported-by: Jian Li <jiali@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Tue, 26 Jul 2011 16:21:17 +0000 (12:21 -0400)]
cifs: don't start signing too early
cifs: don't start signing too early
Sniffing traffic on the wire shows that windows clients send a zeroed
out signature field in a NEGOTIATE request, and send "BSRSPYL" in the
signature field during SESSION_SETUP. Make the cifs client behave the
same way.
It doesn't seem to make much difference in any server that I've tested
against, but it's probably best to follow windows behavior as closely as
possible here.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Tue, 26 Jul 2011 16:20:18 +0000 (12:20 -0400)]
cifs: advertise the right receive buffer size to the server
cifs: advertise the right receive buffer size to the server
Currently, we mirror the same size back to the server that it sends us.
That makes little sense. Instead we should be sending the server the
maximum buffer size that we can handle -- CIFSMaxBufSize minus the
4 byte RFC1001 header.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md: (75 commits)
md/raid10: handle further errors during fix_read_error better.
md/raid10: Handle read errors during recovery better.
md/raid10: simplify read error handling during recovery.
md/raid10: record bad blocks due to write errors during resync/recovery.
md/raid10: attempt to fix read errors during resync/check
md/raid10: Handle write errors by updating badblock log.
md/raid10: clear bad-block record when write succeeds.
md/raid10: avoid writing to known bad blocks on known bad drives.
md/raid10 record bad blocks as needed during recovery.
md/raid10: avoid reading known bad blocks during resync/recovery.
md/raid10 - avoid reading from known bad blocks - part 3
md/raid10: avoid reading from known bad blocks - part 2
md/raid10: avoid reading from known bad blocks - part 1
md/raid10: Split handle_read_error out from raid10d.
md/raid10: simplify/reindent some loops.
md/raid5: Clear bad blocks on successful write.
md/raid5. Don't write to known bad block on doubtful devices.
md/raid5: write errors should be recorded as bad blocks if possible.
md/raid5: use bad-block log to improve handling of uncorrectable read errors.
md/raid5: avoid reading from known bad blocks.
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
ALSA: hda - Fix duplicated DAC assignments for Realtek
ALSA: asihpi - off by one in asihpi_hpi_ioctl()
ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
ALSA: asihpi - bug fix pa use before init.
ALSA: hda - Add support for vref-out based mute LED control on IDT codecs
David S. Miller [Thu, 28 Jul 2011 06:33:03 +0000 (23:33 -0700)]
n2rng: Attach on Niagara-T3.
And stop referring to Victoria Falls, as the attribute we're
talking about is whether the rng is multi-unit capable which
applies to several chip variants now.
Signed-off-by: David S. Miller <davem@davemloft.net>
Durgadoss R [Tue, 12 Jul 2011 11:07:16 +0000 (07:07 -0400)]
hwmon: (coretemp) Add core/pkg threshold support to Coretemp
This patch adds the core and pkg support to coretemp.
These thresholds can be configured via the sysfs interfaces tempX_max
and tempX_max_hyst. An interrupt is generated when CPU temperature reaches
or crosses above tempX_max OR drops below tempX_max_hyst.
This patch is based on the documentation in IA Manual vol 3A, that can be
downloaded from here:
http://download.intel.com/design/processor/manuals/253668.pdf
Signed-off-by: Durgadoss R <durgadoss.r@intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Donggeun Kim [Mon, 20 Jun 2011 07:48:19 +0000 (16:48 +0900)]
hwmon: Driver for NTC Thermistors
Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.
The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: KyungMin Park <kyungmin.park@samsung.com> Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Guenter Roeck [Fri, 10 Jun 2011 01:05:16 +0000 (18:05 -0700)]
hwmon: (max1668) Add support for tempX_fault attributes
MAX1668 and compatibles have several external temperature sensors, but only a
single FAULT status bit. If a fault occurs, the temperature reported on the
affected sensors is 127 degrees C. Use this knowledge to report fault on
external sensors.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Jean Delvare <khali@linux-fr.org>
David George [Thu, 2 Jun 2011 15:43:45 +0000 (08:43 -0700)]
hwmon: Driver for MAX1668
This patch adds support for MAX1668 and compatible temperature sensors.
Signed-off-by: David George <david.george@ska.ac.za>
[guenter.roeck@ericsson.com: minor cleanup of probe error path] Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Michael Holzheu [Thu, 28 Jul 2011 07:06:46 +0000 (09:06 +0200)]
[S390] Export store_status() function
For kdump we need a store status function to save the registers for the
current CPU. Therefore this patch exports a function "store_status()".
In addition to that now also floating point registers are saved correctly.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Stefan Weinhuber [Thu, 28 Jul 2011 07:06:45 +0000 (09:06 +0200)]
[S390] dasd: use vmalloc for statistics input buffer
The size of the buffer that is used to store DASD statistics input
strings depends on the user input. If the input string is to large,
the write operation could fail with -ENOMEM. To avoid this, use
vmalloc instead of kmalloc.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
projects / karo-tx-linux.git / log