This patch fixes a build failure introduced by the patch
ALSA: AACI: factor common hw_params logic into aaci_pcm_hw_params [1]
by adding/moving the aaci struct to the right position.
The patch mentioned above merged common source parts into one function,
but unfortunately left out the aaci struct and consequently caused a
build failure e.g. for arm versatile_config [2]
Takashi Iwai [Fri, 25 Dec 2009 21:49:01 +0000 (22:49 +0100)]
ALSA: hda - Disable tigger at pin-sensing on AD codecs
Analog Device codecs seem to have problems with the triggering of
pin-sensing although their pincaps give the trigger requirements.
Some reported that constant CPU load on HP laptops with AD codecs.
For avoiding this regression, add a flag to codec struct to notify
explicitly that the codec doesn't suppot the trigger at pin-sensing.
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
The second command will produce sound in the analog lineout _as well as_
HDMI sink. The root cause is, device 0 "reuses" the same stream tag that
was used by device 3, and the "intelhdmi - sticky stream id" patch leaves
the HDMI codec in a functional state. So the HDMI codec happily accepts
the audio samples which reuse its stream tag.
The proposed solution is to remember the last device each azx_dev was
assigned to, and prefer to
1) reuse the azx_dev (and hence the stream tag) the HDMI codec last used
2) or assign a never-used azx_dev for HDMI
With this patch and the above two speaker-test commands,
HDMI codec will use stream tag 8 and Analog codec will use 5.
The stream tag used by HDMI codec won't be reused by others, as long
as we don't run out of the 4 playback azx_dev's. The legacy Analog
codec will continue to use stream tag 5 because its device id is 0
(this is a bit tricky).
Linus Torvalds [Thu, 24 Dec 2009 21:01:29 +0000 (13:01 -0800)]
Merge branch 'sysctl' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-misc-2.6
* 'sysctl' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-misc-2.6:
SYSCTL: Add a mutex to the page_alloc zone order sysctl
SYSCTL: Print binary sysctl warnings (nearly) only once
Linus Torvalds [Thu, 24 Dec 2009 21:00:02 +0000 (13:00 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (34 commits)
classmate-laptop: add support for Classmate PC ACPI devices
hp-wmi: Fix two memleaks
acer-wmi, msi-wmi: Remove needless DMI MODULE_ALIAS
dell-wmi: do not keep driver loaded on unsupported boxes
wmi: Free the allocated acpi objects through wmi_get_event_data
drivers/platform/x86/acerhdf.c: check BIOS information whether it begins with string of table
acerhdf: add new BIOS versions
acerhdf: limit modalias matching to supported
toshiba_acpi: convert to seq_file
asus_acpi: convert to seq_file
ACPI: do not select ACPI_DOCK from ATA_ACPI
sony-laptop: enumerate rfkill devices using SN06
sony-laptop: rfkill support for newer models
ACPI: fix OSC regression that caused aer and pciehp not to load
MAINTAINERS: add maintainer for msi-wmi driver
fujitu-laptop: fix tests of acpi_evaluate_integer() return value
arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.c: avoid cross-CPU interrupts by using smp_call_function_any()
ACPI: processor: remove _PDC object list from struct acpi_processor
ACPI: processor: change acpi_processor_set_pdc() interface
ACPI: processor: open code acpi_processor_cleanup_pdc
...
Linus Torvalds [Thu, 24 Dec 2009 20:59:11 +0000 (12:59 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2/trivial: Use le16_to_cpu for a disk value in xattr.c
ocfs2/trivial: Use proper mask for 2 places in hearbeat.c
Ocfs2: Let ocfs2 support fiemap for symlink and fast symlink.
Ocfs2: Should ocfs2 support fiemap for S_IFDIR inode?
ocfs2: Use FIEMAP_EXTENT_SHARED
fiemap: Add new extent flag FIEMAP_EXTENT_SHARED
ocfs2: replace u8 by __u8 in ocfs2_fs.h
ocfs2: explicit declare uninitialized var in user_cluster_connect()
ocfs2-devel: remove redundant OCFS2_MOUNT_POSIX_ACL check in ocfs2_get_acl_nolock()
ocfs2: return -EAGAIN instead of EAGAIN in dlm
ocfs2/cluster: Make fence method configurable - v2
ocfs2: Set MS_POSIXACL on remount
ocfs2: Make acl use the default
ocfs2: Always include ACL support
Linus Torvalds [Thu, 24 Dec 2009 20:57:45 +0000 (12:57 -0800)]
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: pci_request_regions needs a persistent name
ARM: dma-isa: request cascade channel after registering it
ARM: footbridge: trim down old ISA rtc setup
ARM: fix PAGE_KERNEL
ARM: Fix wrong shared bit for CPU write buffer bug test
ARM: 5857/1: ARM: dmabounce: fix build
ARM: 5856/1: Fix bug of uart0 platfrom data for nuc900
ARM: 5855/1: putc support for nuc900
ARM: 5854/1: fix compiling error for NUC900
ARM: 5849/1: ARMv7: fix Oprofile events count
ARM: add missing include to nwflash.c
ARM: Kill CONFIG_CPU_32
ARM: Convert VFP/Crunch/XscaleCP thread_release() to exit_thread()
ARM: 5853/1: ARM: Fix build break on ARM v6 and v7
Linus Torvalds [Thu, 24 Dec 2009 20:54:02 +0000 (12:54 -0800)]
Merge branch 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Ensure all PG_dcache_dirty pages are written back.
sh: mach-ecovec24: setup.c detailed correction
serial: sh-sci: Convert tremaining ctrl_xxx I/O routines to __raw_xxx.
serial: sh-sci: earlyprintk zero uartclk fix
sh: Only use bl bit toggling for sleeping idle.
sh: Restore bl bit toggling in idle loop.
sh: Fix up MAX_DMA_CHANNELS definition when DMA is disabled.
sh: dmaengine support for SH7785
sh: dmaengine support for sh7724.
Russell King [Thu, 24 Dec 2009 12:52:44 +0000 (12:52 +0000)]
ARM: footbridge: trim down old ISA rtc setup
This fixes a "start_kernel(): bug: interrupts were enabled early".
rtc_cmos now takes care of initializing the ISA RTC and reading the
current time and date from it; there's no need to repeat that here,
thereby causing interrupts to be enabled too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 24 Dec 2009 10:16:21 +0000 (10:16 +0000)]
ARM: fix PAGE_KERNEL
PAGE_KERNEL should not be executable; any area marked executable can
be prefetched into the instruction cache. We don't want vmalloc areas
to be read in this way.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Borislav Petkov [Mon, 21 Dec 2009 17:13:01 +0000 (18:13 +0100)]
amd64_edac: make driver loading more robust
Currently, the module does not initialize fully when the DIMMs aren't
ECC but remains still loaded. Propagate the error when no instance of
the driver is properly initialized and prevent further loading.
Reorganize and polish error handling in amd64_edac_init() while at it.
Borislav Petkov [Mon, 21 Dec 2009 13:52:53 +0000 (14:52 +0100)]
amd64_edac: fix K8 chip select reporting
Fix the case when amd64_debug_display_dimm_sizes() reports only half the
amount of DRAM on it because it doesn't account for when the single DCT
operates in 128-bit mode and merges chip selects from different DIMMs.
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
LKML-Reference: <200912112202.48173.johannes.hirte@fem.tu-ilmenau.de> Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
classmate-laptop: add support for Classmate PC ACPI devices
This add supports for devices like keyboard, backlight, tablet and
accelerometer.
This work is supported by International Syst S/A.
[randy.dunlap@oracle.com: cmpc_acpi: depends on ACPI]
[akpm@linux-foundation.org: readability tweaks]
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Markus Pietrek [Thu, 24 Dec 2009 06:12:02 +0000 (15:12 +0900)]
sh: Ensure all PG_dcache_dirty pages are written back.
With some of the cache rework an address aliasing optimization was added,
but this managed to fail on certain mappings resulting in pages with
PG_dcache_dirty set never writing back their dcache lines. This patch
reverts to the earlier behaviour of simply always writing back when the
dirty bit is set.
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 24 Dec 2009 05:52:43 +0000 (14:52 +0900)]
serial: sh-sci: Convert tremaining ctrl_xxx I/O routines to __raw_xxx.
ctrl_xxx() is an antiquated SH interface, while __raw_xxx is the standard
API that accomplishes the same thing. As such, this converts the
remaining sh-sci straggles over, which enables the driver to be wired up
for ARM SH-Mobile CPUs as well.
Now that we have WMI autoloading
the DMI matching is not needed anymore.
Signed-off-by: Thomas Renninger <trenn@suse.de> Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Acked-by: Anisse Astier <anisse@astier.eu> Signed-off-by: Len Brown <len.brown@intel.com>
Anisse Astier [Fri, 4 Dec 2009 09:10:09 +0000 (10:10 +0100)]
wmi: Free the allocated acpi objects through wmi_get_event_data
These function allocate an acpi object by calling wmi_get_event_data, which
then calls acpi_evaluate_object, and it is not freed afterwards.
And kernel doc is fixed for parameters of wmi_get_event_data.
Signed-off-by: Anisse Astier <anisse@astier.eu> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com>
Peter Feuerer [Tue, 22 Dec 2009 00:20:06 +0000 (16:20 -0800)]
drivers/platform/x86/acerhdf.c: check BIOS information whether it begins with string of table
BIOS information is now checked whether it begins with the strings stored
in the BIOS table. Previous method did a strcmp, what lead to problems if
BIOS information has appended whitespaces.
Signed-off-by: Peter Feuerer <peter@piie.net> Cc: Borislav Petkov <petkovbb@gmail.com> Cc: Andreas Mohr <andi@lisas.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Peter Feuerer [Tue, 22 Dec 2009 00:20:05 +0000 (16:20 -0800)]
acerhdf: add new BIOS versions
Add new BIOS versions for following netbooks: Aspire 1810xx, Packard Bell
DOTMU.
Signed-off-by: Peter Feuerer <peter@piie.net> Cc: Borislav Petkov <petkovbb@gmail.com> Cc: Andreas Mohr <andi@lisas.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Stefan Bader [Tue, 22 Dec 2009 00:20:04 +0000 (16:20 -0800)]
acerhdf: limit modalias matching to supported
BugLink: https://bugs.launchpad.net/ubuntu/+bug/435958
The module alias currently matches any Acer computer but when loaded the
BIOS checks will only succeed on Aspire One models. This causes a invalid
BIOS warning for all other models (seen on Aspire 4810T). This is not
fatal but worries users that see this message. Limiting the moule alias
to models starting with AOA or DOA for Packard Bell.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Borislav Petkov <petkovbb@gmail.com> Acked-by: Peter Feuerer <peter@piie.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Alexey Dobriyan [Tue, 22 Dec 2009 00:20:02 +0000 (16:20 -0800)]
toshiba_acpi: convert to seq_file
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Alexey Dobriyan [Tue, 22 Dec 2009 00:20:01 +0000 (16:20 -0800)]
asus_acpi: convert to seq_file
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Corentin Chary <corentincj@iksaif.net> Cc: Karol Kozimor <sziwan@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Carlos R. Mafra [Tue, 22 Dec 2009 21:45:39 +0000 (13:45 -0800)]
ACPI: do not select ACPI_DOCK from ATA_ACPI
In March 2008 commit 0ac4a3c2fbbcadc3e96e4dc47d4ae802d66e6f67 ("ACPI: fix
ATA_ACPI build") made CONFIG_ACPI_DOCK be selected by CONFIG_ATA_ACPI because
of a build error when CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m.
However, in September 2008 commit 898b054f3eec5921320ae8614b5bdd7b07ea5b43
("dock: make dock driver not a module") removed the possibility of having
CONFIG_ACPI_DOCK=m and therefore there is no need for selecting it when
CONFIG_ATA_ACPI=y.
This makes the kernel ~5 Kb smaller for people who don't have a dock by
allowing them to not have ACPI_DOCK compiled-in because of ATA_ACPI=y.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de> Cc: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Mattia Dongili [Wed, 16 Dec 2009 15:08:36 +0000 (00:08 +0900)]
sony-laptop: enumerate rfkill devices using SN06
SN06 makes sure we get back a longer buffer which seems to be necessary
going forward as the SNC devices describes more and more devices (or
features more precisely). Moreover SN06 should be called with only the
descriptor offset to make sure we hit the rfkill controlling function
(F124 or F135) with a 0 argument to get a full list of features.
Mattia Dongili [Wed, 16 Dec 2009 15:08:35 +0000 (00:08 +0900)]
sony-laptop: rfkill support for newer models
Vaio Type X and possibly other new models use F135 as the radio
frequency controlling function attached to the SNC device. In the
indexed table this corresponds to 0x0135 (surpise!).
Signed-off-by: Mattia Dongili <malattia@linux.it> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Thu, 24 Dec 2009 02:27:51 +0000 (18:27 -0800)]
Merge branch 'i2c-fixes' of git://git.fluff.org/bjdooks/linux
* 'i2c-fixes' of git://git.fluff.org/bjdooks/linux:
i2c-omap: OMAP3: Fix I2C lockup during timeout/error cases
i2c-omap: Don't write IE state in unidle if 0
i2c-bfin-twi: fix CLKDIV calculation
Tao Ma [Tue, 22 Dec 2009 02:32:15 +0000 (10:32 +0800)]
ocfs2/trivial: Use proper mask for 2 places in hearbeat.c
I just noticed today that there are 2 places of "mlog(0,...)"
in fs/ocfs2/cluster/heartbeat.c, but actually have no default
mask prefix in that file.
So change them to mlog(ML_HEARTBEAT,...).
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Tristan Ye [Tue, 22 Dec 2009 01:11:58 +0000 (09:11 +0800)]
Ocfs2: Let ocfs2 support fiemap for symlink and fast symlink.
For fast symlink, it can be treated the same as inlined files since
the data extent we want to return of both case all were stored in
metadata block. For symlink, it can be simply treated the same as we
did for regular files.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com> Acked-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Manjunatha GK [Fri, 11 Dec 2009 05:39:08 +0000 (11:09 +0530)]
i2c-omap: OMAP3: Fix I2C lockup during timeout/error cases
Current OMAP3 I2C driver code does not follow the correct sequence for soft
reset. Due to this, lock up issues are reported during timeout/error cases.
This patch fixes above issue by disabling I2C controller as per OMAP3430 TRM
for soft reset. As per TRM, I2C controller needs to be disabled as a first
step during soft reset.
Here is correct soft reset sequence:
a. Ensure that the module is disabled
(clear the I2Ci.I2C_CON[15] I2C_EN bit to 0).
b. Set the I2Ci.I2C_SYSC[1] SRST bit to 1.
c. Enable the module by setting I2Ci.I2C_CON[15] I2C_EN bit to 1.
d. Check the I2Ci.I2C_SYSS[0] RDONE bit until it is set to 1 to
indicate the software reset is complete.
Cory Maccarrone [Wed, 23 Dec 2009 01:06:13 +0000 (18:06 -0700)]
i2c-omap: Don't write IE state in unidle if 0
Commit ef871432... (i2c-omap: OMAP3: PM: (re)init for every transfer
to support off-mode) introduced a change which make the dev->iestate
contents be written to the OMAP_I2C_IE_REG every time omap_i2c_unidle
is called. Previously, the state was only written if it wasn't equal
to zero.
In omap_i2c_probe, omap_i2c_unidle() is called prior to omap_i2c_init(),
in which case dev->iestate has not yet been initialized and will be set
to zero. Having this value written to the registers causes deadlock
while booting.
As such, this change restores the original functionality.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Sonic Zhang [Mon, 21 Dec 2009 14:28:30 +0000 (09:28 -0500)]
i2c-bfin-twi: fix CLKDIV calculation
Calculation of the CLKDIV speed setting should be done using base 10 math
rather than base 2. We also avoid exceeding the spec due to integer
truncation and a 50% duty cycle.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] use resource_size()
[WATCHDOG] iTCO_wdt: add PCI ID for the Intel EP80579 (Tolapai) SoC
As Rafael says:
"... it causes microcode_init_cpu() to be called during resume even for
CPUs for which there's no microcode to apply. That, in turn, results
in executing request_firmware() (on Intel CPUs at least) which doesn't
work at this stage of resume (we have device interrupts disabled, I/O
devices are still suspended and so on).
If I'm not mistaken, the "if (uci->valid)" logic means "if that CPU is
known to us" , so before commit 9f15226e755 microcode_resume_cpu() was
called for all CPUs already in the system during suspend, which was
the right thing to do. The commit changed it so that the CPUs without
microcode to apply are now treated as "unknown", which is not quite
right.
The problem this commit attempted to solve has to be handled
differently."
Bisected-and -requested-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shaohua Li [Wed, 23 Dec 2009 09:04:11 +0000 (17:04 +0800)]
ACPI: fix OSC regression that caused aer and pciehp not to load
Executing _OSC returns a buffer, which has an acpi object in it.
Don't directly returns the buffer, instead, we return the acpi object's
buffer. This fixes a regression since caller of acpi_run_osc expects
an acpi object's buffer returned.
Tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: Fix a bug on appledisplay.c regarding signedness
USB: option: support hi speed for modem Haier CE100
USB: audio gadget: free alsa devices when unloading
USB: audio gadget: fix wTotalLength calculation
usb: otg: isp1301_omap: fix compile error
USB: musb: workaround Blackfin FIFO anomalies
USB: musb: Fix array index out of bounds issue
USB: musb: Fix null pointer dereference issue
USB: musb: correct DMA address for tx
USB: musb: gadget_ep0: avoid SetupEnd interrupt
USB: musb: fix for crash in DM646x USB when (CPPI)DMA is enabled
USB: musb: do not work if no gadget driver is loaded
USB: musb: gadget: set otg tranceiver to idle when registering gadget
USB: musb: Populate the VBUS GPIO with the correct GPIO number
USB: musb: MAINTAINERS: Fix my tree's address
USB: musb: fix compiling warning with min() macro
USB: musb: move musb_remove to __exit
USB: musb_gadget: fix kernel oops in txstate()
USB: ftdi_sio: sort PID/VID entries in new ftdi_sio_ids.h header
USB: ftdi_sio: isolate all device IDs to new ftdi_sio_ids.h header
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
devtmpfs: unlock mutex in case of string allocation error
Driver core: export platform_device_register_data as a GPL symbol
driver core: Prevent reference to freed memory on error path
Driver-core: Fix bogus 0 error return in device_add()
Driver core: driver_attribute parameters can often be const*
Driver core: bin_attribute parameters can often be const*
Driver core: device_attribute parameters can often be const*
Doc/stable rules: add new cherry-pick logic
vfs: get_sb_single() - do not pass options twice
devtmpfs: Convert dirlock to a mutex
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging/vt66*: kconfig, depends on WLAN
Staging: batman-adv: introduce missing kfree
Staging: batman-adv: Add Kconfig dependancies on PROC_FS and PACKET.
Staging: panel: Adjust range for PANEL_KEYPAD in Kconfig
Staging: panel: Fix compilation error with custom lcd charset
Staging: ramzswap: remove ARM specific d-cache hack
Staging: rtl8192x: fix printk formats
Staging: wlan-ng: fix Correct size given to memset
staging: rtl8192su: add USB VID/PID for HWNUm-300
staging: fix rtl8192su compilation errors with mac80211
staging: fix rtl8192e compilation errors with mac80211
Staging: fix rtl8187se compilation errors with mac80211
Staging: rtl8192su: fix test for negative error in rtl8192_rx_isr()
Staging: comedi: jr3_pci: Don't ioremap too much space. Check result.
Staging: comedi: removed "depricated" from COMEDI_CB_BLOCK
Staging: comedi: usbdux.c: fix locking up of the driver when the comedi ringbuffer runs empty
Staging: dst: remove from the tree
Staging: sm7xx: add a new framebuffer driver
Staging: batman: fix debug Kconfig option
Linus Torvalds [Wed, 23 Dec 2009 21:33:07 +0000 (13:33 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Set i_nlink properly during reflink.
ocfs2: Add reflinked file's inode to inode hash eariler.
ocfs2: refcounttree.c cleanup.
ocfs2: Find proper end cpos for a leaf refcount block.
Andi Kleen [Wed, 23 Dec 2009 20:00:47 +0000 (21:00 +0100)]
SYSCTL: Add a mutex to the page_alloc zone order sysctl
The zone list code clearly cannot tolerate concurrent writers (I couldn't
find any locks for that), so simply add a global mutex. No need for RCU
in this case.
Andi Kleen [Wed, 23 Dec 2009 20:00:20 +0000 (21:00 +0100)]
SYSCTL: Print binary sysctl warnings (nearly) only once
When printing legacy sysctls print the warning message
for each of them only once. This way there is a guarantee
the syslog won't be flooded for any sane program.
The original attempt at this made the tables non const and stored
the flag inline.
Linus suggested using a separate hash table for this, this is based on a
code snippet from him.
The hash implies this is not exact and can sometimes not print a
new sysctl due to a hash collision, but in practice this should not
be a problem
I used a FNV32 hash over the binary string with a 32byte bitmap. This
gives relatively little collisions when all the predefined binary sysctls
are hashed:
Russell King [Wed, 23 Dec 2009 19:54:31 +0000 (19:54 +0000)]
ARM: Fix wrong shared bit for CPU write buffer bug test
It is unpredictable to have the same memory mapped using different
shared bit settings for ARMv6 and ARMv7 CPUs. Fix this for the CPU
write buffer bug test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Kevin Hilman <khilman@ti.deeprootsystems.com> Cc: Ulrik Bech Hald <ubh@ti.com> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Ming Lei <tom.leiming@gmail.com> Cc: Vincent Sanders <support@simtec.co.uk> Acked-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Donny Kurnia [Wed, 23 Dec 2009 12:03:12 +0000 (19:03 +0700)]
USB: option: support hi speed for modem Haier CE100
I made this patch for usbserial driver to add the support for EVDO modem
Haier CE100. The bugs report for this is here:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/490068
This patch based on these post:
http://blankblondtank.wordpress.com/2009/09/04/mengoptimalkan-koneksi-modem-haier-ce-100-cdma-di-linux/
http://tantos.web.id/blogs/how-to-internet-connection-using-cdma-evdo-modem-and-karmic-koala-ubuntu-9-10
I hope this patch can help other that have the Haier C100 modem, mostly in my country, Indonesia.
Bryan Wu [Mon, 21 Dec 2009 14:49:52 +0000 (09:49 -0500)]
USB: musb: workaround Blackfin FIFO anomalies
Some of these workarounds are already in place, but labeled as affecting
all BF52x parts. Since we have official anomaly numbers now, use those
defines. And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Tue, 15 Dec 2009 11:30:01 +0000 (13:30 +0200)]
USB: musb: gadget_ep0: avoid SetupEnd interrupt
Gadget stalling a zero-length SETUP request results in this error message:
SetupEnd came in a wrong ep0stage idle
In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero-
length request. Add the missing '\n' to the error message itself as well...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Anand Gadiyar <gadiyar@ti.com> Cc: stable <stable@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Swaminathan S [Tue, 15 Dec 2009 11:30:00 +0000 (13:30 +0200)]
USB: musb: fix for crash in DM646x USB when (CPPI)DMA is enabled
Race condition exists between the cppi_interrupt handler and
davinci_interrupt handler w.r.t completing a TX IO. Since DM646x
has seperate DMA and USB endpoint interrupts cppi_interrupt handler
needs to hold the lock while operating on the endpoint.
Update over previous patch to avoid taking the lock if already
taken. Tested on DM644x, DM355 and DM646x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Felipe Balbi [Tue, 15 Dec 2009 11:47:30 +0000 (13:47 +0200)]
USB: musb: do not work if no gadget driver is loaded
On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cliff Cai [Tue, 15 Dec 2009 09:08:44 +0000 (11:08 +0200)]
USB: musb: fix compiling warning with min() macro
Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
pointer types lacks a cast
So switch to min_t(size_t, ...).
Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Wed, 16 Dec 2009 17:38:31 +0000 (20:38 +0300)]
USB: musb_gadget: fix kernel oops in txstate()
Commit 7723de7e19b744144975a09c81777ec0f14ac5b3 (USB: musb_gadget: remove
pointless loop) included uncalled for (and incorrect) optimization that
might cause a kernel oops in txstate() -- undo it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andreas Mohr [Wed, 16 Dec 2009 20:45:10 +0000 (21:45 +0100)]
USB: ftdi_sio: isolate all device IDs to new ftdi_sio_ids.h header
This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).
Compile-tested, based on latest mainline git.
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Sun, 13 Dec 2009 18:17:16 +0000 (10:17 -0800)]
USB core: fix recent kernel-doc warnings
Fix new kernel-doc warnings in usb core:
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'config'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'iface_num'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'alt_num'
Warning(drivers/usb/core/hcd.c:1622): No description found for parameter 'udev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Beulich [Fri, 20 Nov 2009 13:50:53 +0000 (13:50 +0000)]
USB: fix section mismatch in early ehci dbgp
Commit 917778267fbe67703ab7d5c6f0b7a05d4c3df485 removed __init from
ehci_wait_for_port(), but left it in place on ehci_reset_port(), which
is being called from the former function.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Acked-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clemens Ladisch [Mon, 21 Dec 2009 23:36:44 +0000 (15:36 -0800)]
USB: emi62: fix crash when trying to load EMI 6|2 firmware
While converting emi62 to use request_firmware(), the driver was also
changed to use the ihex helper functions. However, this broke the loading
of the FPGA firmware because the code tries to access the addr field of
the EOF record which works with a plain array that has an empty last
record but not with the ihex helper functions where the end of the data is
signaled with a NULL record pointer, resulting in:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f80d248c>] emi62_load_firmware+0x33c/0x740 [emi62]
This can be fixed by changing the loop condition to test the return value
of ihex_next_binrec() directly (like in emi26.c).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: Der Mickster <retroeffective@gmail.com> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log