Philipp Reisner [Tue, 4 May 2010 14:57:18 +0000 (16:57 +0200)]
drbd: Control the actual resync rate based on the queuing delay of data packets
In a setup with a high bandwidth and high latency network, eventually
involving deep queues in routers, it is beneficial to only fill those
queues up to an limited extend with resync data.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Philipp Reisner [Tue, 4 May 2010 09:12:00 +0000 (11:12 +0200)]
drbd: Four new configuration settings for resync speed control
To reasonably control resync speed over drbd-proxy connections,
drbd has to measure the current delay of packets transmitted over
the (possibly congested) data socket vs the meta-data socket.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Philipp Reisner [Fri, 30 Apr 2010 13:26:20 +0000 (15:26 +0200)]
drbd: Receiving of delay_probes
Delay_probes are new packets in the DRBD protocol, which allow
DRBD to know the current delay packets have on the data socket.
(relative to the meta data socket)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Philipp Reisner [Wed, 28 Apr 2010 12:46:57 +0000 (14:46 +0200)]
drbd: Fixed bitmap in case of online-grow without resync
The "surplus" bits of the old (smaller) bitmap must be clean
in case of online-grow without resync.
Note: Reverted 67ae8b80d4a116ab3b7094eb3723506b20c06dff as
well, since the lines added by this patch are redundant. The
bits get set by the bm_set_surplus(b) call before that.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Adam Gandelman [Thu, 8 Apr 2010 23:48:23 +0000 (16:48 -0700)]
drbd: New handler: initial-split-brain
Some wish to be notified of all instances of split brain, not just those that
go unresolved. The initial-split-brain handler is called to notify someone
upon detection of all split brain conditions even if auto-recovery policies
are configured.
Signed-off-by: Adam Gandelman <adam.gandelman@linbit.com> Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Lars Ellenberg [Tue, 6 Apr 2010 10:15:04 +0000 (12:15 +0200)]
drbd: check for corrupt or malicous sector addresses when receiving data
Even if it should never happen if the peer does behave, we need to
double check, and not even attempt access beyond end of device.
It usually would be caught by lower layers, resulting in "IO error",
but may also end up in the internal meta data area.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Lars Ellenberg [Thu, 1 Apr 2010 14:59:32 +0000 (16:59 +0200)]
drbd: don't start a resync without access to up-to-date Data
In case both nodes are "inconsistent", invalidate would
have started a resync anyways, without a chance to ever
succeed, just filling the logs with warning messages.
Simply disallow that state change,
re-using the SS_NO_UP_TO_DATE_DISK return value.
This also changes the corresponding error string to
"Need access to UpToDate Data" -- I found the
"Refusing to be Primary without at least one UpToDate disk"
answer misleading in some situations anyways.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Philipp Reisner [Wed, 17 Mar 2010 13:18:41 +0000 (14:18 +0100)]
drbd: Do not upgrade state to Outdated if already Inconsistent [Bugz 277]
There was a race condition:
In a situation with a SyncSource+Primary and a SyncTarget+Secondary node,
and a resync dependency to some other device. After both nodes decided
to do the resync, the other device finishes its resync process.
At that time SyncSource already sent the P_SYNC_UUID packet, and
already updated its peer disk state to Inconsistent.
The SyncTarget node waits for the P_SYNC_UUID and sends a state packet
to report the resync dependency change. That packet still carries
a disk state of Outdated.
Impact:
If application writes come in, during that time on the Primary node,
those do not get replicated, and the out-of-sync counter gets increased.
=> The completion of resync is not detected on the primary node.
=> stalled.
Those blocks get resync'ed with the next resync, since the are get
marked as out-of-sync in the bitmap.
In order to fix this, we filter out that wrong state change in the
sanitize_state() function.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Lars Ellenberg [Thu, 11 Mar 2010 15:47:58 +0000 (16:47 +0100)]
drbd: use proc_create_data with explicit NULL argument
To document that we know about deprecation of proc_create,
even though we are not affected, as we don't use the ->data member,
open code proc_create_data(..., NULL);
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Dmitry Monakhov [Fri, 7 May 2010 09:35:44 +0000 (13:35 +0400)]
writeback: Update dirty flags in two steps
Filesystems with delalloc support may dirty inode during writepages.
As result inode will have dirty metadata flags even after write_inode.
In fact we have two dedicated functions for proper data and metadata
writeback. It is reasonable to separate flags updates in two stages.
Jens Axboe [Mon, 17 May 2010 10:55:07 +0000 (12:55 +0200)]
writeback: fix WB_SYNC_NONE writeback from umount
When umount calls sync_filesystem(), we first do a WB_SYNC_NONE
writeback to kick off writeback of pending dirty inodes, then follow
that up with a WB_SYNC_ALL to wait for it. Since umount already holds
the sb s_umount mutex, WB_SYNC_NONE ends up doing nothing and all
writeback happens as WB_SYNC_ALL. This can greatly slow down umount,
since WB_SYNC_ALL writeback is a data integrity operation and thus
a bigger hammer than simple WB_SYNC_NONE. For barrier aware file systems
it's a lot slower.
Jens Axboe [Mon, 17 May 2010 10:51:03 +0000 (12:51 +0200)]
writeback: disable periodic old data writeback for !dirty_writeback_centisecs
Prior to 2.6.32, setting /proc/sys/vm/dirty_writeback_centisecs disabled
periodic dirty writeback from kupdate. This got broken and now causes
excessive sys CPU usage if set to zero, as we'll keep beating on
schedule().
Randy Dunlap [Tue, 11 May 2010 07:02:55 +0000 (09:02 +0200)]
paride: fix menu indentation
Make the PARIDE menu be displayed correctly, with proper/expected
indentation, by moving the GDROM kconfig symbol, which was
splitting the PARIDE kconfig symbol from its dependent symbols.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Mike Snitzer [Tue, 11 May 2010 06:57:42 +0000 (08:57 +0200)]
block: allow initialization of previously allocated request_queue
blk_init_queue() allocates the request_queue structure and then
initializes it as needed (request_fn, elevator, etc).
Split initialization out to blk_init_allocated_queue_node.
Introduce blk_init_allocated_queue wrapper function to model existing
blk_init_queue and blk_init_queue_node interfaces.
Export elv_register_queue to allow a newly added elevator to be
registered with sysfs. Export elv_unregister_queue for symmetry.
These changes allow DM to initialize a device's request_queue with more
precision. In particular, DM no longer unconditionally initializes a
full request_queue (elevator et al). It only does so for a
request-based DM device.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Stephen Rothwell [Thu, 29 Apr 2010 07:32:00 +0000 (09:32 +0200)]
nilfs: fix breakage caused by barrier flag changes
After merging the block tree, today's linux-next build (powerpc ppc64_defconfig)
failed like this:
fs/nilfs2/the_nilfs.c: In function 'nilfs_discard_segments':
fs/nilfs2/the_nilfs.c:673: error: 'DISCARD_FL_BARRIER' undeclared (first use in this function)
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: compute Address Space length rather than using _LEN
x86/PCI: never allocate PCI MMIO resources below BIOS_END
Al Viro [Thu, 29 Apr 2010 02:10:43 +0000 (03:10 +0100)]
nfs d_revalidate() is too trigger-happy with d_drop()
If dentry found stale happens to be a root of disconnected tree, we
can't d_drop() it; its d_hash is actually part of s_anon and d_drop()
would simply hide it from shrink_dcache_for_umount(), leading to
all sorts of fun, including busy inodes on umount and oopsen after
that.
Bug had been there since at least 2006 (commit c636eb already has it),
so it's definitely -stable fodder.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
sfc: Change falcon_probe_board() to fail for unsupported boards
sfc: Always close net device at the end of a disabling reset
sfc: Wait at most 10ms for the MC to finish reading out MAC statistics
sctp: Fix oops when sending queued ASCONF chunks
sctp: fix to calc the INIT/INIT-ACK chunk length correctly is set
sctp: per_cpu variables should be in bh_disabled section
sctp: fix potential reference of a freed pointer
sctp: avoid irq lock inversion while call sk->sk_data_ready()
Revert "tcp: bind() fix when many ports are bound"
net/usb: add sierra_net.c driver
cdc_ether: fix autosuspend for mbm devices
bluetooth: handle l2cap_create_connless_pdu() errors
gianfar: Wait for both RX and TX to stop
ipheth: potential null dereferences on error path
smc91c92_cs: spin_unlock_irqrestore before calling smc_interrupt()
drivers/usb/net/kaweth.c: add device "Allied Telesyn AT-USB10 USB Ethernet Adapter"
bnx2: Update version to 2.0.9.
bnx2: Prevent "scheduling while atomic" warning with cnic, bonding and vlan.
bnx2: Fix lost MSI-X problem on 5709 NICs.
cxgb3: Wait longer for control packets on initialization
...
Ben Hutchings [Wed, 28 Apr 2010 09:01:50 +0000 (09:01 +0000)]
sfc: Change falcon_probe_board() to fail for unsupported boards
The driver needs specific PHY and board support code for each SFC4000
board; there is no point trying to continue if it is missing.
Currently unsupported boards can trigger an 'oops'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Cc: stable@kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
When we finish processing ASCONF_ACK chunk, we try to send
the next queued ASCONF. This action runs the sctp state
machine recursively and it's not prepared to do so.
sctp: fix to calc the INIT/INIT-ACK chunk length correctly is set
When calculating the INIT/INIT-ACK chunk length, we should not
only account the length of parameters, but also the parameters
zero padding length, such as AUTH HMACS parameter and CHUNKS
parameter. Without the parameters zero padding length we may get
following oops.
------------------------------------------------------------------
eth0 has addresses: 3ffe:501:ffff:100:20c:29ff:fe4d:f37e and 192.168.0.21
eth1 has addresses: 192.168.1.21
------------------------------------------------------------------
Reported-by: George Cheimonidis <gchimon@gmail.com> Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When sctp attempts to update an assocition, it removes any
addresses that were not in the updated INITs. However, the loop
may attempt to refrence a transport with address after removing it.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: avoid irq lock inversion while call sk->sk_data_ready()
sk->sk_data_ready() of sctp socket can be called from both BH and non-BH
contexts, but the default sk->sk_data_ready(), sock_def_readable(), can
not be used in this case. Therefore, we have to make a new function
sctp_data_ready() to grab sk->sk_data_ready() with BH disabling.
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
2.6.33-rc6 #129
---------------------------------------------------------
sctp_darn/1517 just changed the state of lock:
(clock-AF_INET){++.?..}, at: [<c06aab60>] sock_def_readable+0x20/0x80
but this lock took another, SOFTIRQ-unsafe lock in the past:
(slock-AF_INET){+.-...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
1 lock held by sctp_darn/1517:
#0: (sk_lock-AF_INET){+.+.+.}, at: [<cdfe363d>] sctp_sendmsg+0x23d/0xc00 [sctp]
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
- Add bio_batch helper primitive. This is rather generic primitive
for submitting/waiting a complex request which consists of several
bios.
- blkdev_issue_zeroout() generate number of zero filed write bios.
x86/PCI: compute Address Space length rather than using _LEN
ACPI _CRS Address Space Descriptors have _MIN, _MAX, and _LEN. Linux has
been computing Address Spaces as [_MIN to _MIN + _LEN - 1]. Based on the
tests in the bug reports below, Windows apparently uses [_MIN to _MAX].
Per spec (ACPI 4.0, Table 6-40), for _CRS fixed-size, fixed location
descriptors, "_LEN must be (_MAX - _MIN + 1)", and when that's true, it
doesn't matter which way we compute the end. But of course, there are
BIOSes that don't follow this rule, and we're better off if Linux handles
those exceptions the same way as Windows.
This patch makes Linux use [_MIN to _MAX], as Windows seems to do. This
effectively reverts d558b483d5 and 03db42adfe and replaces them with
simpler code.
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
coda: move backing-dev.h kernel include inside __KERNEL__
mtd: ensure that bdi entries are properly initialized and registered
Move mtd_bdi_*mappable to mtdcore.c
btrfs: convert to using bdi_setup_and_register()
Catch filesystems lacking s_bdi
drbd: Terminate a connection early if sending the protocol fails
drbd: fix memory leak
Fix JFFS2 sync silent failure
smbfs: add bdi backing to mount session
ncpfs: add bdi backing to mount session
exofs: add bdi backing to mount session
ecryptfs: add bdi backing to mount session
coda: add bdi backing to mount session
cifs: add bdi backing to mount session
afs: add bdi backing to mount session.
9p: add bdi backing to mount session
bdi: add helper function for doing init and register of a bdi for a file system
block: ensure jiffies wrap is handled correctly in blk_rq_timed_out_timer
Elina Pasheva [Wed, 28 Apr 2010 01:06:41 +0000 (18:06 -0700)]
net/usb: add sierra_net.c driver
Re-submitted based on comments from netdev community.
Summary of the changes:
1. Improved error handling.
2. Added the missing timeout arguments to usb_control_msg().
The following is a new Linux driver which exposes certain models of Sierra
Wireless modems to the operating system as Network Interface Cards (NICs).
This driver requires a version of the sierra.c driver which supports
blacklisting to work properly. The blacklist in sierra.c rejects the interfaces
claimed by sierra_net.c. Likewise, the sierra_net.c driver only accepts
(i.e. whitelists) the interface(s) used for USB-to-WWAN traffic.
The version of sierra.c which supports blacklisting is
available from the sierra wireless knowledge base page for older kernels. It is
also available in Linux kernel starting from version 2.6.31.
This driver works with all Sierra Wireless devices configured with PID=68A3
like USB305, USB306 provided the corresponding firmware version is I2.0
(for USB305) or M3.0 (for USB306) and later.
This driver will not work with earlier firmware versions than the ones shown
above. In this case the driver will issue an error message indicating
incompatibility and will not serve the device's USB-to-WWAN interface.
Sierra_net.c sits atop a pre-existing Linux driver called usbnet.c.
A series of hook functions are provided in sierra_net.c which are called by
usbnet.c in response to a particular condition such as receipt or transmission
of a data packet. As such, usbnet.c does most of the work of making
a modem appear to the system as a network device and for properly exchanging
traffic between the USB subsystem and the Network card interface.
Sierra_net.c is concerned with managing the data exchanged between the
USB-to-WWAN interface and the upper layers of the operating system.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com> Signed-off-by: Rory Filer <rfiler@sierrawireless.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Torgny Johansson [Wed, 28 Apr 2010 00:07:40 +0000 (17:07 -0700)]
cdc_ether: fix autosuspend for mbm devices
Autosuspend works until you bring the wwan interface up, then the
device does not enter autosuspend anymore.
The following patch fixes the problem by setting the .manage_power
field in the mbm_info struct to the same as in the cdc_info struct
(cdc_manager_power).
Signed-off-by: Torgny Johansson <torgny.johansson@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Tue, 27 Apr 2010 23:43:31 +0000 (16:43 -0700)]
gianfar: Wait for both RX and TX to stop
When gracefully stopping the controller, the driver was continuing if
*either* RX or TX had stopped. We need to wait for both, or the
controller could get into an invalid state.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
keys: don't need to use RCU in keyring_read() as semaphore is held
David Howells [Tue, 27 Apr 2010 20:13:08 +0000 (13:13 -0700)]
keys: the request_key() syscall should link an existing key to the dest keyring
The request_key() system call and request_key_and_link() should make a
link from an existing key to the destination keyring (if supplied), not
just from a new key to the destination keyring.
This can be tested by:
ring=`keyctl newring fred @s`
keyctl request2 user debug:a a
keyctl request user debug:a $ring
keyctl list $ring
If it says:
keyring is empty
then it didn't work. If it shows something like:
1 key in keyring: 1070462727: --alswrv 0 0 user: debug:a
then it did.
request_key() system call is meant to recursively search all your keyrings for
the key you desire, and, optionally, if it doesn't exist, call out to userspace
to create one for you.
If request_key() finds or creates a key, it should, optionally, create a link
to that key from the destination keyring specified.
Therefore, if, after a successful call to request_key() with a desination
keyring specified, you see the destination keyring empty, the code didn't work
correctly.
If you see the found key in the keyring, then it did - which is what the patch
is required for.
Signed-off-by: David Howells <dhowells@redhat.com> Cc: James Morris <jmorris@namei.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marc Zyngier [Tue, 27 Apr 2010 20:13:07 +0000 (13:13 -0700)]
gpio: fix pca953x set_type 'scheduling while atomic' bug
Bill Gatliff reported the following bug when using the irq_chip facility
of the pca953x driver on a PPC platform:
BUG: scheduling while atomic: insmod/1530/0x00000002
He traced it back to an i2c transaction in pca953x_irq_set_type(), which
can be called with interrupt disabled (from __setup_irq()). As the i2c
controller can sleep while sending a message, this qualifies as a bad
idea.
This patch moves the i2c transaction to pca953x_irq_bus_sync_unlock(),
where it is actually safe to send an i2c message.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Marc Zyngier <maz@misterjones.org> Reported-by: Bill Gatliff <bgat@billgatliff.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Huewe [Tue, 27 Apr 2010 20:13:04 +0000 (13:13 -0700)]
arch/avr32: fix build failure caused by wrong prototype
This patch fixes a build failure introduced by 1d8393171 ("avr32: use
generic ptrace_resume code") which had the static keyword as a leftover.
arch/avr32/kernel/ptrace.c:32: error: static declaration of `user_enable_single_step' follows non-static declaration
include/linux/ptrace.h:268: error: previous declaration of `user_enable_single_step' was here
David Howells [Tue, 27 Apr 2010 21:05:11 +0000 (14:05 -0700)]
keys: don't need to use RCU in keyring_read() as semaphore is held
keyring_read() doesn't need to use rcu_dereference() to access the keyring
payload as the caller holds the key semaphore to prevent modifications
from happening whilst the data is read out.
Signed-off-by: David Howells <dhowells@redhat.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Morris <jmorris@namei.org>
Dan Carpenter [Mon, 26 Apr 2010 23:20:12 +0000 (23:20 +0000)]
ipheth: potential null dereferences on error path
The calls to usb_free_buffer() dereference rx_urb and tx_urb in the
parameter list but those could be NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: L. Alberto Giménez <agimenez@sysvalve.es> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 27 Apr 2010 11:28:10 +0000 (11:28 +0000)]
bnx2: Prevent "scheduling while atomic" warning with cnic, bonding and vlan.
The bonding driver calls ndo_vlan_rx_register() while holding bond->lock.
The bnx2 driver calls bnx2_netif_stop() to stop the rx handling while
changing the vlgrp. The call also stops the cnic driver which sleeps
while the bond->lock is held and cause the warning.
This code path only needs to stop the NAPI rx handling while we are
changing the vlgrp. Since no reset is going to occur, there is no need
to stop cnic in this case. By adding a parameter to bnx2_netif_stop()
to skip stopping cnic, we can avoid the warning.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 27 Apr 2010 11:28:09 +0000 (11:28 +0000)]
bnx2: Fix lost MSI-X problem on 5709 NICs.
It has been reported that under certain heavy traffic conditions in MSI-X
mode, the driver can lose an MSI-X vector causing all packets in the
associated rx/tx ring pair to be dropped. The problem is caused by
the chip dropping the write to unmask the MSI-X vector by the kernel
(when migrating the IRQ for example).
This can be prevented by increasing the GRC timeout value for these
register read and write operations.
Thanks to Dell for helping us debug this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Detsch [Mon, 26 Apr 2010 05:38:27 +0000 (05:38 +0000)]
cxgb3: Wait longer for control packets on initialization
In some Power7 platforms, when using VIOS (Virtual I/O Server), we
need to wait longer for control packets to finish transfer during
initialization.
Without this change, initialization may fail prematurely.
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com> Signed-off-by: Andre Detsch <adetsch@br.ibm.com> Acked-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 27 Apr 2010 03:33:04 +0000 (03:33 +0000)]
e1000e: enable/disable ASPM L0s and L1 and ERT according to hardware errata
Prompted by a previous patch submitted by Matthew Garret <mjg@redhat.com>,
further digging into errata documentation reveals the current enabling or
disabling of ASPM L0s and L1 states for certain parts supported by this
driver are incorrect. 82571 and 82572 should always disable L1. For
standard frames, 82573/82574/82583 can enable L1 but L0s must be disabled,
and for jumbo frames 82573/82574 must disable L1. This allows for some
parts to enable L1 in certain configurations leading to better power
savings.
Also according to the same errata, Early Receive (ERT) should be disabled
on 82573 when using jumbo frames.
Cc: Matthew Garret <mjg@redhat.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Waskiewicz [Tue, 27 Apr 2010 00:38:15 +0000 (00:38 +0000)]
ixgbe: Power down PHY during driver resets
The PHY laser is still on during driver init. It's allowing
garbage to hit our FIFO, which eventually can cause the entire
device to die. Power down the laser while setting up the device,
and re-enable the laser before getting link.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Egger [Mon, 26 Apr 2010 14:56:36 +0000 (15:56 +0100)]
Remove redundant check for CONFIG_MMU
The checks for CONFIG_MMU at this location are duplicated as all the code is
located inside a #ifndef CONFIG_MMU block. So the first conditional block will
always be included while the second never will.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (39 commits)
omap: delete unused bootloader tag variables
omap: Devkit8000: Remove unused pins
omap: Devkit8000: Change position of init calls
omap: Devkit8000: Remove unnecessary include file
omap: Devkit8000: Fix typo in pin name
omap: Devkit8000: Add missing package selection
omap: Devkit8000: Fix typo in supplies
n8x0_defconfig: remove CONFIG_NILFS2_FS override
omap: board-sdp-flash.c: Fix typos in debug output
omap4: Fix McBSP4 base address
omap: rx51_defconfig: Remove CONFIG_SYSFS_DEPRECATED*=y options
omap: rx51_defconfig: Remove duplicate phonet
omap: fix a gpmc nand problem
AM3517: initialize i2c subsystem after mux subsystem
omap: remove one of the define of INT_34XX_BENCH_MPU_EMUL
omap: fix the compile error if CONFIG_MTD_NAND_OMAP2 is notenabled
OMAP4: Clocks: Change SPI Instance Names
omap: Devkit8000: Fix wrong usb port on Devkit8000
OMAP4: Fix for CONTROL register Base
OMAP4-HSMMC: FIX for MMC5 Controller IRQ Base
...
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: Fix sparc regression in r300_scratch()
drm: make sure vblank interrupts are disabled at DPMS time
drm/radeon/kms/evergreen: No EnableYUV table
drm/radeon: 9800 SE has only one quadpipe
drm/radeon/kms: don't print error for legal crtcs.
drm/radeon/kms/evergreen: fix LUT setup
Currently, device claiming for exclusive open is done after low level
open - disk->fops->open() - has completed successfully. This means
that exclusive open attempts while a device is already exclusively
open will fail only after disk->fops->open() is called.
cdrom driver issues commands during open() which means that O_EXCL
open attempt can unintentionally inject commands to in-progress
command stream for burning thus disturbing burning process. In most
cases, this doesn't cause problems because the first command to be
issued is TUR which most devices can process in the middle of burning.
However, depending on how a device replies to TUR during burning,
cdrom driver may end up issuing further commands.
This can't be resolved trivially by moving bd_claim() before doing
actual open() because that means an open attempt which will end up
failing could interfere other legit O_EXCL open attempts.
ie. unconfirmed open attempts can fail others.
This patch resolves the problem by introducing claiming block which is
started by bd_start_claiming() and terminated either by bd_claim() or
bd_abort_claiming(). bd_claim() from inside a claiming block is
guaranteed to succeed and once a claiming block is started, other
bd_start_claiming() or bd_claim() attempts block till the current
claiming block is terminated.
bd_claim() can still be used standalone although now it always
synchronizes against claiming blocks, so the existing users will keep
working without any change.
blkdev_open() and open_bdev_exclusive() are converted to use claiming
blocks so that exclusive open attempts from these functions don't
interfere with the existing exclusive open.
This problem was discovered while investigating bko#15403.
https://bugzilla.kernel.org/show_bug.cgi?id=15403
The burning problem itself can be resolved by updating userspace
probing tools to always open w/ O_EXCL.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Matthias-Christian Ott <ott@mirix.org> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
CC booke_wdt.o
booke_wdt.c: In function 'booke_wdt_init':
booke_wdt.c:220: error: assignment of read-only variable 'ident'
Fix this by removing 'const' qualifier from watchdog_info struct.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
David Miller [Mon, 26 Apr 2010 09:55:42 +0000 (02:55 -0700)]
drm/radeon: Fix sparc regression in r300_scratch()
Commit b4fe945405e477cded91772b4fec854705443dd5 ("drm/radeon: Fix
memory allocation failures in the preKMS command stream checking.")
added a regression in that it completely tossed the get_unaligned()
done by r300_scratch() which we added in commit 958a6f8ccb1964adc3eec84cf401c5baeb4fbca0 ("drm: radeon: Fix unaligned
access in r300_scratch().").
Put it back.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jesse Barnes [Fri, 26 Mar 2010 18:07:15 +0000 (18:07 +0000)]
drm: make sure vblank interrupts are disabled at DPMS time
When we call drm_vblank_off() at DPMS off time (to wake any clients so
they don't hang) we need to make sure interrupts are actually disabled.
If drm_vblank_off() gets called before the vblank usage timer expires,
it'll prevent the timer from disabling interrupts since it also clears
the vblank_enabled flag for the pipe.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Neil Brown [Tue, 20 Apr 2010 02:16:52 +0000 (12:16 +1000)]
nfsd4: bug in read_buf
When read_buf is called to move over to the next page in the pagelist
of an NFSv4 request, it sets argp->end to essentially a random
number, certainly not an address within the page which argp->p now
points to. So subsequent calls to READ_BUF will think there is much
more than a page of spare space (the cast to u32 ensures an unsigned
comparison) so we can expect to fall off the end of the second
page.
We never encountered thsi in testing because typically the only
operations which use more than two pages are write-like operations,
which have their own decoding logic. Something like a getattr after a
write may cross a page boundary, but it would be very unusual for it to
cross another boundary after that.
Cc: stable@kernel.org Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
x86/PCI: never allocate PCI MMIO resources below BIOS_END
When we move a PCI device or assign resources to a device not configured
by the BIOS, we want to avoid the BIOS region below 1MB. Note that if the
BIOS places devices below 1MB, we leave them there.
See https://bugzilla.kernel.org/show_bug.cgi?id=15744
and https://bugzilla.kernel.org/show_bug.cgi?id=15841
Tested-by: Andy Isaacson <adi@hexapodia.org> Tested-by: Andy Bailey <bailey@akamai.com> Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
bridge br_multicast: Ensure to initialize BR_INPUT_SKB_CB(skb)->mrouters_only.
Even with commit 32dec5dd0233ebffa9cae25ce7ba6daeb7df4467 ("bridge
br_multicast: Don't refer to BR_INPUT_SKB_CB(skb)->mrouters_only
without IGMP snooping."), BR_INPUT_SKB_CB(skb)->mrouters_only is
not appropriately initialized if IGMP snooping support is
compiled and disabled, so we can see garbage.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt [Mon, 26 Apr 2010 18:20:32 +0000 (11:20 -0700)]
ieee802154: Fix oops during ieee802154_sock_ioctl
Trying to run izlisten (from lowpan-tools tests) on a device that does not
exists I got the oops below. The problem is that we are using get_dev_by_name
without checking if we really get a device back. We don't in this case and
writing to dev->type generates this oops.
[Oops code removed by Dmitry Eremin-Solenikov]
If possible this patch should be applied to the current -rc fixes branch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Detsch [Mon, 26 Apr 2010 07:27:07 +0000 (07:27 +0000)]
tg3: Fix INTx fallback when MSI fails
tg3: Fix INTx fallback when MSI fails
MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.
In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log