The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1'
enables a wakesource, 0 disables it.
The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.
The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.
For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:
This patch also removes the homebrew CPU frequency switching code. I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Manuel Lauss [Sun, 21 Dec 2008 08:26:25 +0000 (09:26 +0100)]
MIPS: Alchemy: Fix up PM code on Au1550/Au1200
Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).
Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sun, 21 Dec 2008 08:26:24 +0000 (09:26 +0100)]
MIPS: Alchemy: move calc_clock function.
Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sun, 21 Dec 2008 08:26:22 +0000 (09:26 +0100)]
MIPS: make cp0 counter clocksource/event usable as fallback.
The current mips clock build infrastructure lets a system only use
either the MIPS cp0 counter or a SoC specific timer as a clocksource /
clockevent device.
This patch renames the core cp0 counter clocksource / clockevent functions
from mips_* to r4k_* and updates the wrappers in asm-mips/time.h to
call these renamed functions instead.
Chips which can detect whether it is safe to use a chip-specific timer
can now fall back on the cp0 counter if necessary and possible
(e.g. Alchemy with a follow-on patch).
Existing behaviour is not changed in any way.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sun, 21 Dec 2008 08:26:21 +0000 (09:26 +0100)]
MIPS: Alchemy: remove cpu_table.
Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code: Activation of this features should be
left to the boards using the chips since it also affects external devices
tied to BCLK, and only the board designers know whether it is safe to
enable.
Manuel Lauss [Sun, 21 Dec 2008 08:26:17 +0000 (09:26 +0100)]
MIPS: Alchemy: update core interrupt code.
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Manuel Lauss [Sun, 21 Dec 2008 08:26:16 +0000 (09:26 +0100)]
MIPS: Alchemy: move commandline mangling out of common code
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sun, 21 Dec 2008 08:26:15 +0000 (09:26 +0100)]
MIPS: Alchemy: devboards: consolidate files
Share some code and merge small files:
- Extract the prom init code from all devboard files (they only differ in
memory configuration).
- Merge the irq configuration into board setup code.
- Merge smaller files into board setup code.
David Daney [Thu, 11 Dec 2008 23:33:36 +0000 (15:33 -0800)]
MIPS: Adjust the dma-common.c platform hooks.
We add a dev parameter to plat_unmap_dma_mem(), and hooks for
plat_dma_supported() and plat_extra_sync_for_device() which should be
nop changes for all existing targets.
Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 11 Dec 2008 23:33:28 +0000 (15:33 -0800)]
MIPS: Hook up Cavium OCTEON in arch/mips.
Take all the OCTEON specific files that were added, and hook them into
the build system for the arch/mips. For versions of GCC that lack
OCTEON support, override gas target architecture.
David Daney [Thu, 11 Dec 2008 23:33:25 +0000 (15:33 -0800)]
MIPS: Override assembler target architecture for octeon.
Gas from binutils 2.19 fails to compile some cop1 instructions with
-march=octeon. Since the cop1 instructions are present in mips1, use
that arch instead. This will be fixed in binutils 2.20.
Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Fri, 9 Jan 2009 00:46:40 +0000 (16:46 -0800)]
MIPS: Add Cavium OCTEON processor support files to arch/mips/cavium-octeon.
These are the rest of the new files needed to add OCTEON processor
support to the Linux kernel. Other than Makefile and Kconfig which
should be obvious, we have:
csrc-octeon.c -- Clock source driver for OCTEON.
dma-octeon.c -- Helper functions for mapping DMA memory.
flash_setup.c -- Register on-board flash with the MTD subsystem.
octeon-irq.c -- OCTEON interrupt controller managment.
octeon-memcpy.S -- Optimized memcpy() implementation.
serial.c -- Register 8250 platform driver and early console.
setup.c -- Early architecture initialization.
smp.c -- OCTEON SMP support.
octeon_switch.S -- Scheduler context switch for OCTEON.
c-octeon.c -- OCTEON cache controller support.
cex-oct.S -- OCTEON cache exception handler.
asm/mach-cavium-octeon/*.h -- Architecture include files.
David Daney [Tue, 23 Dec 2008 23:22:14 +0000 (15:22 -0800)]
MIPS: Add Cavium OCTEON processor support files to arch/mips/cavium-octeon/executive and asm/octeon.
These files are used to coordinate resource sharing between all of
the programs running on the OCTEON SOC. The OCTEON processor has many
CPU cores (current parts have up to 16, but more are possible). It
also has a variety of on-chip hardware blocks for things like network
acceleration, encryption and RAID.
One typical configuration is to run Linux on several of the CPU cores,
and other dedicated applications on the other cores.
Resource allocation between the various programs running on the system
(Linux kernel and other dedicated applications) needs to be
coordinated. The code we use to do this we call the 'executive'. All
of this resource allocation and sharing code is gathered together in
the executive directory.
Included in the patch set are the following files:
cvmx-bootmem.c and cvmx-sysinfo.c -- Coordinate memory allocation.
All memory used by the Linux kernel is obtained here at boot time.
cvmx-l2c.c -- Coordinates operations on the shared level 2 cache.
octeon-model.c -- Probes chip capabilities and version.
David Daney [Thu, 11 Dec 2008 23:33:19 +0000 (15:33 -0800)]
MIPS: Add Cavium OCTEON processor CSR definitions
Here we define the addresses and bit-fields of the Configuration and
Status Registers (CSRs) for some of the hardware functional units on
the OCTEON SOC.
Definitions are needed for:
CIU -- Central Interrupt Unit.
GPIO -- General Purpose Input Output.
IOB -- Input / Output {Busing,Bridge}.
IPD -- Input Packet Data unit.
L2C -- Level-2 Cache controller.
L2D -- Level-2 Data cache.
L2T -- Level-2 cache Tag.
LED -- Light Emitting Diode controller.
MIO -- Miscellaneous Input / Output.
POW -- Packet Order / Work unit.
Arjan van de Ven [Sat, 10 Jan 2009 18:03:05 +0000 (10:03 -0800)]
bootgraph: make the bootgraph script show async waiting time
It is useful for diagnosing boot performance to see where async function
calls are waiting on serialization... this patch adds this
functionality to the bootgraph.pl script.
The waiting time is shown as a half transparent, gray bar through the
block that is waiting.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Sat, 10 Jan 2009 18:18:44 +0000 (10:18 -0800)]
libata: only ports >= 0 need to synchronize
In a discussio with Jeff Garzik, he mentioned that the serialization
for the libata port probes only needs to be within the domain of a host.
This means that for the first port of each host (with ID 0), we don't
need to wait, so we can relax our serialization a little.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 10 Jan 2009 14:13:09 +0000 (06:13 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86: fix section mismatch warnings in mcheck/mce_amd_64.c
x86: offer frame pointers in all build modes
x86: remove duplicated #include's
x86: k8 numa register active regions later
x86: update Alan Cox's email addresses
x86: rename all fields of mpc_table mpc_X to X
x86: rename all fields of mpc_oemtable oem_X to X
x86: rename all fields of mpc_bus mpc_X to X
x86: rename all fields of mpc_cpu mpc_X to X
x86: rename all fields of mpc_intsrc mpc_X to X
x86: rename all fields of mpc_lintsrc mpc_X to X
x86: rename all fields of mpc_iopic mpc_X to X
x86: irqinit_64.c init_ISA_irqs should be static
Documentation/x86/boot.txt: payload length was changed to payload_length
x86: setup_percpu.c fix style problems
x86: irqinit_64.c fix style problems
x86: irqinit_32.c fix style problems
x86: i8259.c fix style problems
x86: irq_32.c fix style problems
x86: ioport.c fix style problems
...
Linus Torvalds [Sat, 10 Jan 2009 14:12:18 +0000 (06:12 -0800)]
Merge branch 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
[IA64] fix typo in cpumask_of_pcibus()
x86: fix x86_32 builds for summit and es7000 arch's
cpumask: use work_on_cpu in acpi-cpufreq.c for read_measured_perf_ctrs
cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
cpumask: use cpumask_var_t in acpi-cpufreq.c
cpumask: use work_on_cpu in acpi/cstate.c
cpumask: convert struct cpufreq_policy to cpumask_var_t
cpumask: replace CPUMASK_ALLOC etc with cpumask_var_t
x86: cleanup remaining cpumask_t ops in smpboot code
cpumask: update pci_bus_show_cpuaffinity to use new cpumask API
cpumask: update local_cpus_show to use new cpumask API
ia64: cpumask fix for is_affinity_mask_valid()
Linus Torvalds [Sat, 10 Jan 2009 14:09:52 +0000 (06:09 -0800)]
btrfs: fix for write_super_lockfs/unlockfs error handling
Commit c4be0c1dc4cdc37b175579be1460f15ac6495e9a added the ability for
write_super_lockfs to return errors, and renamed them to match. But
btrfs didn't get converted.
Do the minimal conversion to make it compile again.
Artem Bityutskiy [Sat, 10 Jan 2009 11:12:09 +0000 (11:12 +0000)]
rbtree: add const qualifier to some functions
The 'rb_first()', 'rb_last()', 'rb_next()' and 'rb_prev()' calls
take a pointer to an RB node or RB root. They do not change the
pointed objects, so add a 'const' qualifier in order to make life
of the users of these functions easier.
Indeed, if I have my own constant pointer &const struct my_type *p,
and I call 'rb_next(&p->rb)', I get a GCC warning:
warning: passing argument 1 of ‘rb_next’ discards qualifiers from pointer target type
Eric Piel [Sat, 10 Jan 2009 00:41:01 +0000 (16:41 -0800)]
LIS3LV02D: separate the core from HP ACPI API
The sensor can be accessed via various buses. In particular, SPI, I²C
and, on HP laptops, via a specific ACPI API (the only one currently
supported). Separate this latest platform from the core of the sensor
driver to allow support for the other bus type. The second, and more
direct goal is actually to be able to merge this part with the
hp-disk-leds driver, which has the same ACPI PNP number.
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ioctls for the generic freeze feature are below.
o Freeze the filesystem
int ioctl(int fd, int FIFREEZE, arg)
fd: The file descriptor of the mountpoint
FIFREEZE: request code for the freeze
arg: Ignored
Return value: 0 if the operation succeeds. Otherwise, -1
o Unfreeze the filesystem
int ioctl(int fd, int FITHAW, arg)
fd: The file descriptor of the mountpoint
FITHAW: request code for unfreeze
arg: Ignored
Return value: 0 if the operation succeeds. Otherwise, -1
Error number: If the filesystem has already been unfrozen,
errno is set to EINVAL.
[akpm@linux-foundation.org: fix CONFIG_BLOCK=n] Signed-off-by: Takashi Sato <t-sato@yk.jp.nec.com> Signed-off-by: Masayuki Hamaguchi <m-hamaguchi@ys.jp.nec.com> Cc: <xfs-masters@oss.sgi.com> Cc: <linux-ext4@vger.kernel.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Kleikamp <shaggy@austin.ibm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Alasdair G Kergon <agk@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Sato [Sat, 10 Jan 2009 00:40:58 +0000 (16:40 -0800)]
filesystem freeze: add error handling of write_super_lockfs/unlockfs
Currently, ext3 in mainline Linux doesn't have the freeze feature which
suspends write requests. So, we cannot take a backup which keeps the
filesystem's consistency with the storage device's features (snapshot and
replication) while it is mounted.
In many case, a commercial filesystem (e.g. VxFS) has the freeze feature
and it would be used to get the consistent backup.
If Linux's standard filesystem ext3 has the freeze feature, we can do it
without a commercial filesystem.
So I have implemented the ioctls of the freeze feature.
I think we can take the consistent backup with the following steps.
1. Freeze the filesystem with the freeze ioctl.
2. Separate the replication volume or create the snapshot
with the storage device's feature.
3. Unfreeze the filesystem with the unfreeze ioctl.
4. Take the backup from the separated replication volume
or the snapshot.
This patch:
VFS:
Changed the type of write_super_lockfs and unlockfs from "void"
to "int" so that they can return an error.
Rename write_super_lockfs and unlockfs of the super block operation
freeze_fs and unfreeze_fs to avoid a confusion.
ext3, ext4, xfs, gfs2, jfs:
Changed the type of write_super_lockfs and unlockfs from "void"
to "int" so that write_super_lockfs returns an error if needed,
and unlockfs always returns 0.
reiserfs:
Changed the type of write_super_lockfs and unlockfs from "void"
to "int" so that they always return 0 (success) to keep a current behavior.
Signed-off-by: Takashi Sato <t-sato@yk.jp.nec.com> Signed-off-by: Masayuki Hamaguchi <m-hamaguchi@ys.jp.nec.com> Cc: <xfs-masters@oss.sgi.com> Cc: <linux-ext4@vger.kernel.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Kleikamp <shaggy@austin.ibm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Alasdair G Kergon <agk@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Harvey Harrison [Sat, 10 Jan 2009 00:40:56 +0000 (16:40 -0800)]
memstick: annotate endianness of attribute structs
The code was shifting the endianness appropriately everywhere, annotate
the structs to avoid the sparse warnings when assigning the endian types
to the struct members, or passing them to be[16|32]_to_cpu:
drivers/memstick/core/mspro_block.c:331:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:333:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:335:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:337:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:341:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:347:4: warning: cast to restricted __be32
drivers/memstick/core/mspro_block.c:356:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:358:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:364:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:367:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:369:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:371:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:377:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:478:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:480:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:482:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:484:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:486:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:689:22: expected unsigned int [unsigned] [assigned] data_address
drivers/memstick/core/mspro_block.c:689:22: got restricted __be32 [usertype] <noident>
drivers/memstick/core/mspro_block.c:697:3: warning: cast to restricted __be32
drivers/memstick/core/mspro_block.c:960:17: warning: incorrect type in initializer (different base types)
drivers/memstick/core/mspro_block.c:960:17: expected unsigned short [unsigned] data_count
drivers/memstick/core/mspro_block.c:960:17: got restricted __be16 [usertype] <noident>
drivers/memstick/core/mspro_block.c:993:6: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:995:28: warning: cast to restricted __be16
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Alex Dubov <oakad@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Larry Finger [Sat, 10 Jan 2009 00:40:54 +0000 (16:40 -0800)]
hp-wmi: handle rfkill_register() failure
Compilation of the HP WMI hotkeys code results in the following:
CC [M] drivers/platform/x86/hp-wmi.o
drivers/platform/x86/hp-wmi.c: In function hp_wmi_bios_setup:
drivers/platform/x86/hp-wmi.c:431: warning: ignoring return value of rfkill_register,
declared with attribute warn_unused_result
drivers/platform/x86/hp-wmi.c:441: warning: ignoring return value of rfkill_register,
declared with attribute warn_unused_result
drivers/platform/x86/hp-wmi.c:450: warning: ignoring return value of rfkill_register,
declared with attribute warn_unused_result
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Sat, 10 Jan 2009 00:40:52 +0000 (16:40 -0800)]
CORE_DUMP_DEFAULT_ELF_HEADERS depends on ELF_CORE
Kernels that don't support ELF coredumps at all surely can't be supporting
new partial-segment flavored ELF coredumps ... don't make folk answer
Kconfig questions about that flavor.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Roland McGrath <roland@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/arjan/linux-2.6-async-2:
async: make async a command line option for now
partial revert of asynchronous inode delete
Linus Torvalds [Fri, 9 Jan 2009 23:30:30 +0000 (15:30 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: core: fix sleep in atomic context due to driver core change
Linus Torvalds [Fri, 9 Jan 2009 23:27:39 +0000 (15:27 -0800)]
Merge branch 'for_2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6
* 'for_2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6: (28 commits)
mISDN: Add HFC USB driver
mISDN: Add layer1 prim MPH_INFORMATION_REQ
mISDN: Fix kernel crash when doing hardware conference with more than two members
mISDN: Added missing create_l1() call
mISDN: Add MODULE_DEVICE_TABLE() to hfcpci
mISDN: Minor cleanups
mISDN: Create /sys/class/mISDN
mISDN: Add missing release functions
mISDN: Add different different timer settings for hfc-pci
mISDN: Minor fixes
mISDN: Correct busy device detection
mISDN: Fix deactivation, if peer IP is removed from l1oip instance.
mISDN: Add ISDN_P_TE_UP0 / ISDN_P_NT_UP0
mISDN: Fix irq detection
mISDN: Add ISDN sample clock API to mISDN core
mISDN: Return error on E-channel access
mISDN: Add E-Channel logging features
mISDN: Use protocol to detect D-channel
mISDN: Fixed more indexing bugs
mISDN: Make debug output a little bit more verbose
...
Stefan Richter [Fri, 9 Jan 2009 19:49:37 +0000 (20:49 +0100)]
firewire: core: fix sleep in atomic context due to driver core change
Due to commit 2831fe6f9cc4e16c103504ee09a47a084297c0f3, "driver core:
create a private portion of struct device", device_initialize() can no
longer be called from atomic contexts.
We now defer it until after config ROM probing. This requires changes
to the bus manager code because this may use a device before it was
probed.
Reported-by: Jay Fenlason <fenlason@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-nommu:
NOMMU: Support XIP on initramfs
NOMMU: Teach kobjsize() about VMA regions.
FLAT: Don't attempt to expand the userspace stack to fill the space allocated
FDPIC: Don't attempt to expand the userspace stack to fill the space allocated
NOMMU: Improve procfs output using per-MM VMAs
NOMMU: Make mmap allocation page trimming behaviour configurable.
NOMMU: Make VMAs per MM as for MMU-mode linux
NOMMU: Delete askedalloc and realalloc variables
NOMMU: Rename ARM's struct vm_region
NOMMU: Fix cleanup handling in ramfs_nommu_get_umapped_area()
Linus Torvalds [Fri, 9 Jan 2009 21:56:06 +0000 (13:56 -0800)]
Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] update documentation for hvc_iucv kernel parameter.
[S390] hvc_iucv: Special handling of IUCV HVC devices
[S390] hvc_iucv: Refactor console and device initialization
[S390] hvc_iucv: Update function documentation
[S390] hvc_iucv: Limit rate of outgoing IUCV messages
[S390] hvc_iucv: Change IUCV term id and use one device as default
[S390] Use unsigned long long for u64 on 64bit.
[S390] qdio: fix broken pointer in case of CONFIG_DEBUG_FS is disabled
[S390] vdso: compile fix
[S390] remove code for oldselect system call
[S390] types: add/fix types.h include in header files
[S390] dasd: add device attribute to disable blocking on lost paths
[S390] dasd: send change uevents for dasd block devices
[S390] tape block: fix dependencies
[S390] asm-s390/posix_types.h: drop __USE_ALL usage
[S390] gettimeofday.S: removed duplicated #includes
[S390] ptrace: no extern declarations for userspace
Linus Torvalds [Fri, 9 Jan 2009 21:55:37 +0000 (13:55 -0800)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: ledtrig-timer - on deactivation hardware blinking should be disabled
leds: Add suspend/resume to the core class
leds: Add WM8350 LED driver
leds: leds-pcs9532 - Move i2c work to a workqueque
leds: leds-pca9532 - fix memory leak and properly handle errors
leds: Fix wrong loop direction on removal in leds-ams-delta
leds: fix Cobalt Raq LED dependency
leds: Fix sparse warning in leds-ams-delta
leds: Fixup kdoc comment to match parameter names
leds: Make header variable naming consistent
leds: eds-pca9532: mark pca9532_event() static
leds: ALIX.2 LEDs driver
Linus Torvalds [Fri, 9 Jan 2009 21:55:13 +0000 (13:55 -0800)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Rename the corgi backlight driver to generic
backlight: add support for Toppoly TDO35S series to tdo24m lcd driver
backlight: Add suspend/resume support to the backlight core
bd->props.brightness doesn't reflect the actual backlight level.
backlight: Support VGA/QVGA mode switching in tosa_lcd
backlight: Catch invalid input in sysfs attributes
backlight: Value of ILI9320_RGB_IF2 register should not be hardcoded
backlight: crbllcd_bl - Use platform_device_register_simple()
backlight: progear_bl - Use platform_device_register_simple()
backlight: hp680_bl - Use platform_device_register_simple()
Martin Bachem [Tue, 4 Nov 2008 13:11:22 +0000 (14:11 +0100)]
mISDN: Add layer1 prim MPH_INFORMATION_REQ
MPH_INFORMATION provides full D- and B-Channel status overview
- new layer1 primitive: MPF_INFORMATON_REQ
- layer1 replies with MPH_INFORMATION_IND containing
- dch->[state,Flags,nrbchan]
- bch[]->[protocol,Flags]
- hardware driver should send MPH_INFORMATION_IND
on all ph state changes and BChannel state changes to MISDN_ID_ANY
Signed-off-by: Martin Bachem <m.bachem@gmx.de> Signed-off-by: Karsten Keil <kkeil@suse.de>
Add missing release function of ec-devices. Each device require a relase
function now. All destruction (memory and list entry) must be done within
the given release function of device, rather than after unregistering device.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu> Signed-off-by: Karsten Keil <kkeil@suse.de>
mISDN: Add different different timer settings for hfc-pci
- Poll-timer can now be set from 8 to 256 samples, depending on your kernel.
- If default or 128 is used, the normal controller's clock is used as before.
Usage: modprobe hfcpci poll=XXX
- Added some debug code for dsp buffer size. (CMX_DELAY_DEBUG)
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu> Signed-off-by: Karsten Keil <kkeil@suse.de>
Martin Bachem [Wed, 3 Sep 2008 13:17:45 +0000 (15:17 +0200)]
mISDN: Add E-Channel logging features
New prim PH_DATA_E_IND.
- all E-ch frames are indicated by recv_Echannel(), which pushes E-Channel
frames into dch's rqueue
- if dchannel is opened with channel nr 0, no E-Channel logging
is requested
- if dchannel is opened with channel nr 1, E-Channel logging
is requested. if layer1 does not support that, -EINVAL
in return is appropriate
Signed-off-by: Martin Bachem <m.bachem@gmx.de> Signed-off-by: Karsten Keil <kkeil@suse.de>
mISDN: Add feature via MISDN_CTRL_FILL_EMPTY to fill fifo if empty
This prevents underrun of fifo when filled and in case of an underrun it
prevents subsequent underruns due to jitter.
Improve dsp, so buffers are kept filled with a certain delay, so moderate
jitter will not cause underrun all the time -> the audio quality is highly
improved. tones are not interrupted by gaps anymore, except when CPU is
stalling or in high load.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu> Signed-off-by: Karsten Keil <kkeil@suse.de>
'rb_prev()', 'rb_next()' and 'rb_replace_node()' are declared in
include/linux/rbtree.h, no need for JFFS2 to re-declare them. I
believe these are left-overs from the old days when the common
RB tree code did not have those call and JFFS2 had private
implementation.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
projects / linux-beck.git / log