Stephen Warren [Fri, 7 Mar 2014 19:22:16 +0000 (12:22 -0700)]
pinctrl: tegra: dynamically calculate function list of groups
The per-SoC data structures for Tegra pinctrl stored some information
in a redundant way. Specifically, the list of groups that each function
could be muxed onto was stored once explicitly, and also as part of the
definition of each group. Eliminate this redundancy, and calculate each
function's list of valid groups at pinctrl probe time. This removes
thousands of lines of code from the pinctrl driver and ~16K from the
vmlinux binary size, and adds only about 500uS to the boot process (on
Tegra30; newer SoCs will likely be faster still).
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stephen Warren [Fri, 7 Mar 2014 19:22:15 +0000 (12:22 -0700)]
pinctrl: tegra: init Tegra20/30 at module_init time
The Tegra20/30 pinctrl drivers currently initializes at arch_initcall,
whereas Tegra114/124 pinctrl drivers initialize at module_init time.
Convert Tegra20/30 to work the same way as the other drivers.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Maxime COQUELIN [Wed, 12 Mar 2014 08:50:08 +0000 (09:50 +0100)]
pinctrl: st: Use ARRAY_SIZE instead of raw value for number of delays
This patch replaces the raw values with ARRAY_SIZE for assigning the
ninput_delays and noutput_delays fields of STiH416's st_pctl_data struct.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: st: add pinctrl support for the STiH407 SoC
This patch adds the initial support for pinctrl based on H407 SoC.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: st: Enhance the controller to manage unavailable registers
This patch adds a new logic inside the st pinctrl to manage
an unsupported scenario: some sysconfig are not available!
This is the case of STiH407 where, although documented, the
following registers from SYSCFG_FLASH have been removed from the SoC.
SYSTEM_CONFIG3040
Output Enable pad control for all PIO Alternate Functions
and
SYSTEM_ CONFIG3050
Pull Up pad control for all PIO Alternate Functions
Without managing this condition an imprecise external abort
will be detect.
To do this the patch also reviews the st_parse_syscfgs
and other routines to manipulate the registers only if
actually available.
In any case, for example the st_parse_syscfgs detected
an error condition but no action was made in the
st_pctl_probe_dt.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stephen Boyd [Fri, 7 Mar 2014 06:44:46 +0000 (22:44 -0800)]
pinctrl: msm: Simplify msm_config_reg() and callers
We don't need to check for a negative reg here because reg is
always the same and is always non-negative. Also, collapse the
switch statement down for the duplicate cases.
Stephen Boyd [Fri, 7 Mar 2014 06:44:41 +0000 (22:44 -0800)]
pinctrl: msm: Check for ngpios > MAX_NR_GPIO
Fail the probe and print a warning if SoC specific drivers have
more GPIOs than there can be accounted for in the static bitmaps.
This should avoid silent corruption/failures in the future.
Josh Cartwright [Wed, 5 Mar 2014 19:33:08 +0000 (13:33 -0600)]
pinctrl: msm: drop wake_irqs bitmap
Currently, the wake_irqs bitmap is used to track whether there are any
gpio's which are configured as wake irqs, and uses this to determine
whether or not to call enable_irq_wake()/disable_irq_wake() on the
summary interrupt.
However, the genirq core already handles this case, by maintaining a
'wake_count' per irq_desc, and only calling into the controlling
irq_chip when wake_count transitions 0 <-> 1.
Drop this bitmap, and unconditionally call irq_set_irq_wake() on the
summary interrupt.
Chew, Kean Ho [Thu, 6 Mar 2014 13:59:49 +0000 (21:59 +0800)]
pinctrl-baytrail: add function mux checking in gpio pin request
The requested gpio pin must has the func_pin_mux field set
to GPIO function by BIOS/FW in advanced. Else, the gpio pin
request would fail. This is to ensure that we do not expose
any gpio pins which shall be used for alternate functions,
for eg: wakeup pin, I/O interfaces for LPSS, etc.
Signed-off-by: Chew, Kean Ho <kean.ho.chew@intel.com> Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stephen Boyd [Wed, 26 Feb 2014 19:12:23 +0000 (11:12 -0800)]
devicetree: bindings: Make msm8974-pinctrl documentation match code
The compatible string doesn't have an x in it. Fix it. Also
remove the "qcom" prefix from pins and functions as this binding
uses the generic pinctrl bindings for the pins and functions.
Linus Walleij [Mon, 3 Mar 2014 05:39:20 +0000 (13:39 +0800)]
Merge tag 'mvebu-pinctrl-3.15' of git://git.infradead.org/linux-mvebu into pinctrl-mvebu
mvebu pinctrl changes for v3.15
- various cleanup and refactorization
- add drivers for the Armada 375, 380, and 385 SoCs
- prepare dove for SoC code moving into mach-mvebu
- DT documentation updates
Now that we have a regmap for global registers, get rid of the last
remaining hardcoded physical addresses. While at it, also remove
DOVE_ prefix from those macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: mvebu: dove: request syscon regmap for global registers
Dove pinctrl uses some global config registers to control pins.
This patch requests a syscon regmap for those registers. As this
changes DT to driver requirements, fallback to a self-registered
regmap with hardcoded resources, if the corresponding syscon DT
node is missing. Also, WARN about old DT binding usage to encourage
users to update their DTBs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
Dove pinctrl also requires additional registers to control all pins.
This patch requests resources for mpp4 and pmu-mpp register ranges.
As this changes DT to driver requirements, fallback to hardcoded
resources, if the corresponding DT regs have not been set.
Also, WARN about old DT binding usage to encourage users to update
their DTBs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
Dove pinctrl binding now requires three different reg properties. This
updates corresponding binding and example accordingly. While at it, also
document reg property as required for the other MVEBU SoC pinctrl nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Thomas Petazzoni [Mon, 10 Feb 2014 17:04:56 +0000 (18:04 +0100)]
pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385
The Marvell Armada 380/385 are new ARM SoCs from Marvell, part of the
mvebu family, but using a Cortex-A9 CPU core. In terms of pin-muxing,
it is similar to Armada 370 and XP for the register layout, only
different in the number of available pins and their
functions. Therefore, we simply use the existing
drivers/pinctrl/mvebu/ infrastructure, with no other changes that the
list of pins and corresponding functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Thomas Petazzoni [Mon, 10 Feb 2014 17:04:55 +0000 (18:04 +0100)]
pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375
The Marvell Armada 375 is a new ARM SoC from Marvell, part of the
mvebu family, but using a Cortex-A9 CPU core. In terms of pin-muxing,
it is similar to Armada 370 and XP for the register layout, only
different in the number of available pins and their
functions. Therefore, we simply use the existing
drivers/pinctrl/mvebu/ infrastructure, with no other changes that the
list of pins and corresponding functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Passing a NULL name for pin ranges will auto-generate standard names
for each pin. With common pinctrl driver now checking NULL name correctly,
consolidate mpp pins 0-15.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Thomas Petazzoni [Thu, 13 Feb 2014 16:11:27 +0000 (17:11 +0100)]
pinctrl: mvebu: remove MPP_REG_CTRL macro
Now that each per-SoC pinctrl driver must implement its own get/set
functions, there is no point in keeping the MPP_REG_CTRL macro, whose
purpose was to let the core pinctrl mvebu driver use default get/set
functions. While at it also update the comment about mvebu_mpp_ctrl.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
With every SoC always providing its own get/set callbacks, we can now
remove the generic ones, remove the obsolete base address, and always
use the provided callbacks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
pinctrl: mvebu: move resource allocation to SoC specific drivers
The way that mvebu pinctrl is designed, requesting mpp registers
in common pinctrl driver does not allow SoC specific drivers to
access this resource.
Move resource allocation in each SoC pinctrl driver and enable
already provided mpp_{set,get} callbacks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
pinctrl: mvebu: armada-xp: provide generic mpp callbacks
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
pinctrl: mvebu: armada-370: provide generic mpp callbacks
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
pinctrl: mvebu: kirkwood: provide generic mpp callbacks
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch>
pinctrl: mvebu: dove: provide generic mpp callbacks
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later. While at it, also make use of globally defined
MPP macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
pinctrl: mvebu: add common mpp reg helper to mvebu pinctrl include
This adds some defines and helper functions for the common mpp reg
layout to mvebu pinctrl include.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested-by: Andrew Lunn <andrew@lunn.ch>
pinctrl: mvebu: remove passing mvebu_mpp_ctrl to callbacks
The only valuable information a special callback can derive from
mvebu_mpp_ctrl passed to it, is the pin id. Instead of passing
the struct, pass the pid directly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We treat unnamed controls as generic mvebu mpp register controls but
we identify them by not being special controls. Flip the logic and
use the name pointer as identification instead. While at it, add some
comments explaining the not so obvious treatment.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
pinctrl: mvebu: remove obsolete per-control name buffer allocation
With the introduction of a global name buffer, we can now remove
the allocation and preparation of per-control name buffers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
pinctrl: mvebu: count unnamed controls and allocate name buffer
pinctrl-mvebu allows SoCs to pass unnamed controls that will get an
auto-generated name of "mpp<PIN#>". Currently, we are allocating name
buffers on a per-control basis while looping over passed controls.
This counts the total number of unnamed controls and allocates a
global name buffer instead. The new buffer is then used while assigning
controls to pinctrl groups later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Hans de Goede [Mon, 17 Feb 2014 21:19:41 +0000 (22:19 +0100)]
pinctrl-sunxi: Fix sun5i-a13 port F multiplexing
The correct value for selecting the mmc0 function on port F pins is 2 not 4,
as per the data-sheet:
http://dl.linux-sunxi.org/A13/A13%20Datasheet%20-%20v1.12%20%282012-03-29%29.pdf
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sonic Zhang [Fri, 14 Feb 2014 10:21:06 +0000 (18:21 +0800)]
pinctrl: pinctrl-adi: combine multiple groups of one function together
The data pins of some peripheral are different if connecting to different
devices in one pinmux function. In the PPI case, data pins can be used
in 8, 16 and 24 pin groups individually. Add these groups into one ppi
function.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A QSPI function set consists of 3 groups:
- qspi_ctrl (2 control wires)
- qspi_data2 (2 data wires, for Single/Dual SPI)
- qspi_data4 (4 data wires, for Quad SPI)
Mark Brown [Thu, 30 Jan 2014 18:57:20 +0000 (18:57 +0000)]
pinctrl: Quiet logging about missing DT nodes when not using DT
On systems which were not booted using DT it is entirely unsurprising that
device nodes don't have any DT information and this is going to happen for
every single device in the system. Make pinctrl be less chatty about this
situation by only logging in the case where we have DT.
Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rongjun Ying [Thu, 30 Jan 2014 05:54:24 +0000 (13:54 +0800)]
pinctrl: sirf: add pin group for USP0 for atlas6
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
commit 8385af02bad only added this group for prima2, and missed
atlas6. This patch fixes it.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Chao Xie [Tue, 28 Jan 2014 07:20:44 +0000 (15:20 +0800)]
pinctrl: single: add low power mode support
For some silicons, the pin configuration register can control
the output of the pin when the pad including the pin enter
low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when
the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage
when the SOC enter low power mode, and can save more power for
the low power mode.
A QSPI function set consists of 3 groups:
- qspi_ctrl (2 control wires)
- qspi_data2 (2 data wires, for Single/Dual SPI)
- qspi_data4 (4 data wires, for Quad SPI)
pinctrl: st: Add software edge trigger interrupt support
ST pin controller does not have hardware support for detecting edge
triggered interrupts, It only has level triggering support.
This patch attempts to fake up edge triggers from hw level trigger
support in software. With this facility now the gpios can be easily used
for keypads, otherwise it would be difficult for drivers like keypads to
work with level trigger interrupts.
This patch add interrupt support to the pincontroller driver.
ST Pincontroller GPIO bank can have one of the two possible types of
interrupt-wirings.
First type is via irqmux, single interrupt is used by multiple gpio
banks. This reduces number of overall interrupts numbers required. All
these banks belong to a single pincontroller.
_________
| |----> [gpio-bank (n) ]
| |----> [gpio-bank (n + 1)]
[irqN]-- | irq-mux |----> [gpio-bank (n + 2)]
| |----> [gpio-bank (... )]
|_________|----> [gpio-bank (n + 7)]
Second type has a dedicated interrupt per gpio bank.
Linus Torvalds [Mon, 10 Feb 2014 02:14:53 +0000 (18:14 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull SELinux fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
SELinux: Fix kernel BUG on empty security contexts.
selinux: add SOCK_DIAG_BY_FAMILY to the list of netlink message types
Linus Torvalds [Mon, 10 Feb 2014 02:12:07 +0000 (18:12 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes, both -stable fodder. The O_SYNC bug is fairly
old..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a kmap leak in virtio_console
fix O_SYNC|O_APPEND syncing the wrong range on write()
Al Viro [Sun, 2 Feb 2014 12:05:05 +0000 (07:05 -0500)]
fix a kmap leak in virtio_console
While we are at it, don't do kmap() under kmap_atomic(), *especially*
for a page we'd allocated with GFP_KERNEL. It's spelled "page_address",
and had that been more than that, we'd have a real trouble - kmap_high()
can block, and doing that while holding kmap_atomic() is a Bad Idea(tm).
Al Viro [Sun, 9 Feb 2014 20:18:09 +0000 (15:18 -0500)]
fix O_SYNC|O_APPEND syncing the wrong range on write()
It actually goes back to 2004 ([PATCH] Concurrent O_SYNC write support)
when sync_page_range() had been introduced; generic_file_write{,v}() correctly
synced
pos_after_write - written .. pos_after_write - 1
but generic_file_aio_write() synced
pos_before_write .. pos_before_write + written - 1
instead. Which is not the same thing with O_APPEND, obviously.
A couple of years later correct variant had been killed off when
everything switched to use of generic_file_aio_write().
All users of generic_file_aio_write() are affected, and the same bug
has been copied into other instances of ->aio_write().
The fix is trivial; the only subtle point is that generic_write_sync()
ought to be inlined to avoid calculations useless for the majority of
calls.
Linus Torvalds [Sun, 9 Feb 2014 19:12:26 +0000 (11:12 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix data corruption when reading/updating compressed extents
Btrfs: don't loop forever if we can't run because of the tree mod log
btrfs: reserve no transaction units in btrfs_ioctl_set_features
btrfs: commit transaction after setting label and features
Btrfs: fix assert screwup for the pending move stuff
Linus Torvalds [Sun, 9 Feb 2014 18:09:49 +0000 (10:09 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Tooling fixes, mostly related to the KASLR fallout, but also other
fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf buildid-cache: Check relocation when checking for existing kcore
perf tools: Adjust kallsyms for relocated kernel
perf tests: No need to set up ref_reloc_sym
perf symbols: Prevent the use of kcore if the kernel has moved
perf record: Get ref_reloc_sym from kernel map
perf machine: Set up ref_reloc_sym in machine__create_kernel_maps()
perf machine: Add machine__get_kallsyms_filename()
perf tools: Add kallsyms__get_function_start()
perf symbols: Fix symbol annotation for relocated kernel
perf tools: Fix include for non x86 architectures
perf tools: Fix AAAAARGH64 memory barriers
perf tools: Demangle kernel and kernel module symbols too
perf/doc: Remove mention of non-existent set_perf_event_pending() from design.txt
Btrfs: fix data corruption when reading/updating compressed extents
When using a mix of compressed file extents and prealloc extents, it
is possible to fill a page of a file with random, garbage data from
some unrelated previous use of the page, instead of a sequence of zeroes.
A simple sequence of steps to get into such case, taken from the test
case I made for xfstests, is:
This results in the following file items in the fs tree:
item 4 key (257 INODE_ITEM 0) itemoff 15879 itemsize 160
inode generation 6 transid 6 size 542872 block group 0 mode 100600
item 5 key (257 INODE_REF 256) itemoff 15863 itemsize 16
inode ref index 2 namelen 6 name: foobar
item 6 key (257 EXTENT_DATA 0) itemoff 15810 itemsize 53
extent data disk byte 0 nr 0 gen 6
extent data offset 0 nr 24576 ram 266240
extent compression 0
item 7 key (257 EXTENT_DATA 24576) itemoff 15757 itemsize 53
prealloc data disk byte 12849152 nr 241664 gen 6
prealloc data offset 0 nr 241664
item 8 key (257 EXTENT_DATA 266240) itemoff 15704 itemsize 53
extent data disk byte 12845056 nr 4096 gen 6
extent data offset 0 nr 20480 ram 20480
extent compression 2
item 9 key (257 EXTENT_DATA 286720) itemoff 15651 itemsize 53
prealloc data disk byte 13090816 nr 405504 gen 6
prealloc data offset 0 nr 258048
The on disk extent at offset 266240 (which corresponds to 1 single disk block),
contains 5 compressed chunks of file data. Each of the first 4 compress 4096
bytes of file data, while the last one only compresses 3024 bytes of file data.
Therefore a read into the file region [285648 ; 286720[ (length = 4096 - 3024 =
1072 bytes) should always return zeroes (our next extent is a prealloc one).
The solution here is the compression code path to zero the remaining (untouched)
bytes of the last page it uncompressed data into, as the information about how
much space the file data consumes in the last page is not known in the upper layer
fs/btrfs/extent_io.c:__do_readpage(). In __do_readpage we were correctly zeroing
the remainder of the page but only if it corresponds to the last page of the inode
and if the inode's size is not a multiple of the page size.
This would cause not only returning random data on reads, but also permanently
storing random data when updating parts of the region that should be zeroed.
For the example above, it means updating a single byte in the region [285648 ; 286720[
would store that byte correctly but also store random data on disk.
A test case for xfstests follows soon.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com> Signed-off-by: Chris Mason <clm@fb.com>
Josef Bacik [Fri, 7 Feb 2014 18:57:59 +0000 (13:57 -0500)]
Btrfs: don't loop forever if we can't run because of the tree mod log
A user reported a 100% cpu hang with my new delayed ref code. Turns out I
forgot to increase the count check when we can't run a delayed ref because of
the tree mod log. If we can't run any delayed refs during this there is no
point in continuing to look, and we need to break out. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com>
David Sterba [Fri, 7 Feb 2014 13:34:04 +0000 (14:34 +0100)]
btrfs: reserve no transaction units in btrfs_ioctl_set_features
Added in patch "btrfs: add ioctls to query/change feature bits online"
modifications to superblock don't need to reserve metadata blocks when
starting a transaction.
Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com>
Jeff Mahoney [Fri, 7 Feb 2014 13:33:57 +0000 (14:33 +0100)]
btrfs: commit transaction after setting label and features
The set_fslabel ioctl uses btrfs_end_transaction, which means it's
possible that the change will be lost if the system crashes, same for
the newly set features. Let's use btrfs_commit_transaction instead.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com>
Josef Bacik [Wed, 5 Feb 2014 21:19:21 +0000 (16:19 -0500)]
Btrfs: fix assert screwup for the pending move stuff
Wang noticed that he was failing btrfs/030 even though me and Filipe couldn't
reproduce. Turns out this is because Wang didn't have CONFIG_BTRFS_ASSERT set,
which meant that a key part of Filipe's original patch was not being built in.
This appears to be a mess up with merging Filipe's patch as it does not exist in
his original patch. Fix this by changing how we make sure del_waiting_dir_move
asserts that it did not error and take the function out of the ifdef check.
This makes btrfs/030 pass with the assert on or off. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Filipe Manana <fdmanana@gmail.com> Signed-off-by: Chris Mason <clm@fb.com>
Linus Torvalds [Sat, 8 Feb 2014 22:31:39 +0000 (14:31 -0800)]
Merge tag 'pinctrl-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"First round of pin control fixes for v3.14:
- Protect pinctrl_list_add() with the proper mutex. This was
identified by RedHat. Caused nasty locking warnings was rootcased
by Stanislaw Gruszka.
- Avoid adding dangerous debugfs files when either half of the
subsystem is unused: pinmux or pinconf.
- Various fixes to various drivers: locking, hardware particulars, DT
parsing, error codes"
* tag 'pinctrl-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: tegra: return correct error type
pinctrl: do not init debugfs entries for unimplemented functionalities
pinctrl: protect pinctrl_list add
pinctrl: sirf: correct the pin index of ac97_pins group
pinctrl: imx27: fix offset calculation in imx_read_2bit
pinctrl: vt8500: Change devicetree data parsing
pinctrl: imx27: fix wrong offset to ICONFB
pinctrl: at91: use locked variant of irq_set_handler
Linus Torvalds [Sat, 8 Feb 2014 19:54:43 +0000 (11:54 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Quite a varied little collection of fixes. Most of them are
relatively small or isolated; the biggest one is Mel Gorman's fixes
for TLB range flushing.
A couple of AMD-related fixes (including not crashing when given an
invalid microcode image) and fix a crash when compiled with gcov"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Unify valid container checks
x86, hweight: Fix BUG when booting with CONFIG_GCOV_PROFILE_ALL=y
x86/efi: Allow mapping BGRT on x86-32
x86: Fix the initialization of physnode_map
x86, cpu hotplug: Fix stack frame warning in check_irq_vectors_for_cpu_disable()
x86/intel/mid: Fix X86_INTEL_MID dependencies
arch/x86/mm/srat: Skip NUMA_NO_NODE while parsing SLIT
mm, x86: Revisit tlb_flushall_shift tuning for page flushes except on IvyBridge
x86: mm: change tlb_flushall_shift for IvyBridge
x86/mm: Eliminate redundant page table walk during TLB range flushing
x86/mm: Clean up inconsistencies when flushing TLB ranges
mm, x86: Account for TLB flushes only when debugging
x86/AMD/NB: Fix amd_set_subcaches() parameter type
x86/quirks: Add workaround for AMD F16h Erratum792
x86, doc, kconfig: Fix dud URL for Microcode data
Dave Kleikamp [Fri, 7 Feb 2014 20:36:10 +0000 (14:36 -0600)]
jfs: fix generic posix ACL regression
I missed a couple errors in reviewing the patches converting jfs
to use the generic posix ACL function. Setting ACL's currently
fails with -EOPNOTSUPP.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Reported-by: Michael L. Semon <mlsemon35@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Linus Torvalds [Fri, 7 Feb 2014 22:17:18 +0000 (14:17 -0800)]
Merge tag 'driver-core-3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single kernfs fix to resolve a much-reported lockdep issue
with the removal of entries in sysfs"
* tag 'driver-core-3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: make kernfs_deactivate() honor KERNFS_LOCKDEP flag
Linus Torvalds [Fri, 7 Feb 2014 20:35:56 +0000 (12:35 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph fixes from Sage Weil:
"There is an RBD fix for a crash due to the immutable bio changes, an
error path fix, and a locking fix in the recent redirect support"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: do not dereference a NULL bio pointer
libceph: take map_sem for read in handle_reply()
libceph: factor out logic from ceph_osdc_start_request()
libceph: fix error handling in ceph_osdc_init()
Linus Torvalds [Fri, 7 Feb 2014 20:19:50 +0000 (12:19 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Relax VDSO alignment requirements so that the kernel-picked one (4K)
does not conflict with the dynamic linker's one (64K)
- VDSO gettimeofday fix
- Barrier fixes for atomic operations and cache flushing
- TLB invalidation when overriding early page mappings during boot
- Wired up new 32-bit arm (compat) syscalls
- LSM_MMAP_MIN_ADDR when COMPAT is enabled
- defconfig update
- Clean-up (comments, pgd_alloc).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: Expand default enabled features
arm64: asm: remove redundant "cc" clobbers
arm64: atomics: fix use of acquire + release for full barrier semantics
arm64: barriers: allow dsb macro to take option parameter
security: select correct default LSM_MMAP_MIN_ADDR on arm on arm64
arm64: compat: Wire up new AArch32 syscalls
arm64: vdso: update wtm fields for CLOCK_MONOTONIC_COARSE
arm64: vdso: fix coarse clock handling
arm64: simplify pgd_alloc
arm64: fix typo: s/SERRROR/SERROR/
arm64: Invalidate the TLB when replacing pmd entries during boot
arm64: Align CMA sizes to PAGE_SIZE
arm64: add DSB after icache flush in __flush_icache_all()
arm64: vdso: prevent ld from aligning PT_LOAD segments to 64k
Linus Torvalds [Fri, 7 Feb 2014 20:19:06 +0000 (12:19 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"hree minor patches. All have sat in -next for a few days"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Fix build when CONFIG_BUG is not set
MIPS: Wire up sched_setattr/sched_getattr syscalls
MIPS: Alchemy: Fix DB1100 GPIO registration
Linus Torvalds [Fri, 7 Feb 2014 20:16:36 +0000 (12:16 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of small fixes. Mostly driver ones. There is one core
regression fix on a patch that was meant to fix some race issues on
vb2, but that actually caused more harm than good. So, we're just
reverting it for now"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] adv7842: Composite free-run platfrom-data fix
[media] v4l2-dv-timings: fix GTF calculation
[media] hdpvr: Fix memory leak in debug
[media] af9035: add ID [2040:f900] Hauppauge WinTV-MiniStick 2
[media] mxl111sf: Fix compile when CONFIG_DVB_USB_MXL111SF is unset
[media] mxl111sf: Fix unintentional garbage stack read
[media] cx24117: use a valid dev pointer for dev_err printout
[media] cx24117: remove dead code in always 'false' if statement
[media] update Michael Krufky's email address
[media] vb2: Check if there are buffers before streamon
[media] Revert "[media] videobuf_vm_{open,close} race fixes"
[media] go7007-loader: fix usb_dev leak
[media] media: bt8xx: add missing put_device call
[media] exynos4-is: Compile in fimc-lite runtime PM callbacks conditionally
[media] exynos4-is: Compile in fimc runtime PM callbacks conditionally
[media] exynos4-is: Fix error paths in probe() for !pm_runtime_enabled()
[media] s5p-jpeg: Fix wrong NV12 format parameters
[media] s5k5baf: allow to handle arbitrary long i2c sequences
Linus Torvalds [Fri, 7 Feb 2014 20:14:24 +0000 (12:14 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix PMBus driver problem with some multi-page voltage sensors and fix
da9055 interrupt initialization"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (da9055) Remove use of regmap_irq_get_virq()
hwmon: (pmbus) Support per-page exponent in linear mode
Linus Torvalds [Fri, 7 Feb 2014 20:12:21 +0000 (12:12 -0800)]
Merge tag 'pm+acpi-3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These include a fix for a recent ACPI hotplug regression, four
concurrency related fixes and one PCI device removal fix for
ACPI-based PCI hotplug (ACPIPHP), intel_pstate fix that should go into
stable, three simple ACPI cleanups and a new entry for the ACPI video
blacklist.
Specifics:
- Fix for a recent ACPI hotplug regression causing a NULL pointer
dereference to occur while handling ACPI eject notifications for
already ejected devices. From Toshi Kani.
- Four concurrency-related fixes for ACPIPHP. Two of them add
missing locking and the other two fix race conditions related to
reference counting.
- ACPIPHP fix to avoid NULL pointer dereferences during device
removal involving Virtual Funcions.
- intel_pstate fix to make it compute the percentage of time the CPU
is busy properly. From Dirk Brandewie.
- Removal of two unnecessary NULL pointer checks in ACPI code and a
fix for sscanf() format string from Dan Carpenter and Luis G.F.
- New ACPI video blacklist entry for HP EliteBook Revolve 810 from
Mika Westerberg"
* tag 'pm+acpi-3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / hotplug: Fix panic on eject to ejected device
ACPI / battery: Fix incorrect sscanf() string in acpi_battery_init_alarm()
ACPI / proc: remove unneeded NULL check
ACPI / utils: remove a pointless NULL check
ACPI / video: Add HP EliteBook Revolve 810 to the blacklist
intel_pstate: Take core C0 time into account for core busy calculation
ACPI / hotplug / PCI: Fix bridge removal race vs dock events
ACPI / hotplug / PCI: Fix bridge removal race in handle_hotplug_event()
ACPI / hotplug / PCI: Scan root bus under the PCI rescan-remove lock
ACPI / hotplug / PCI: Move PCI rescan-remove locking to hotplug_event()
ACPI / hotplug / PCI: Remove entries from bus->devices in reverse order
projects / linux-beck.git / log