Samuel Ortiz [Fri, 3 Jul 2009 00:00:48 +0000 (02:00 +0200)]
cfg80211: check for current_bss from giwrate
When connecting to an ESSID manually, we may not set the BSSID, and thus
wdev->wext.connect.bssid will be NULL.
wdev->current_bss is always updated when a connection is established so we
should check it first.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Wed, 1 Jul 2009 13:17:35 +0000 (15:17 +0200)]
rt2x00: use wiphy rfkill interface
Remove the input_polldev from rt2x00 and replace it with
the rfkill interface offered by the wiphy structure. This
simplifies the entire rfkill handling in rt2x00 and allows
us to remove the CONFIG_RT2X00_LIB_RFKILL option and always
enables rfkill capabilities.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Tue, 30 Jun 2009 12:49:18 +0000 (14:49 +0200)]
mac80211: shorten the passive dwell time for sw scans
mac80211's software scan implementation uses a passive dwell time of
(HZ / 5) which means we stay 200ms on each passive channel. Compared
to iwlwifi's hw scan and the old ipw* drivers which use values around
120ms this is quite long.
Reducing the passive dwell time from 200ms to 125ms should save us
something around a second on cards capable of 11a and we should still be
able to catch beacons from most access points (assuming a ~100ms beacon
interval).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 25 Jun 2009 10:28:31 +0000 (18:28 +0800)]
iwmc3200wifi: simplify calibration map
The patch simplifies calibration map by combining the init_calib_map
and periodic_calib_map into one calib_map in struct iwm_conf. Now the
initial calibration map is stored in the lower 16 bits of calib_map
and the periodic calibration map is stored in the higher 16 bits.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 25 Jun 2009 10:28:30 +0000 (18:28 +0800)]
iwmc3200wifi: replace netif_rx with netif_rx_ni
The patch uses netif_rx_ni() over netif_rx() to post buffers to
upper network code because it is always scheduled in a workqueue.
The problem was first observed from a dynamic ticks warning:
"NOHZ: local_softirq_pending ..."
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the remaining p54 files to account for the new file organization.
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the TX/RX code from p54common.c into a new file txrx.c
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the mac80211 glue code from p54common.c into a new file main.c
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the LMAC Interface specific definitions from p54common.h into a new file lmac.h
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the LED code from p54common.c into a new file led.c
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the firmware i/o code from p54common.c into a new file fwio.c
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the eeprom code from p54common.h into a new file eeprom.h
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the eeprom code from p54common.c into a new file eeprom.c
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrey Yurovsky reported that the driver forwarded erroneously the
parent device structure instead of the real thing, which of course
led to some dodgy sysfs links (at least?).
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 19 Jun 2009 20:52:45 +0000 (13:52 -0700)]
iwlwifi: unify iwl_setup_rxon_timing
This patch unifies setup_rxon_timing funcions
of AGN and 3945. HWs differ only in supported maximal
beacon interval. This is reflected in hw_paras.max_beacon_itrvl
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 19 Jun 2009 20:52:44 +0000 (13:52 -0700)]
iwlwifi: scan requested channels only
When userspace requests only certain channels to be scanned,
we currently ignore that request entirely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 19 Jun 2009 20:52:43 +0000 (13:52 -0700)]
iwlwifi: make software queue assignment more efficient
There really is no reason to be assigning txq->swq_id all the
time, once at aggregation setup is sufficient.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 19 Jun 2009 20:52:42 +0000 (13:52 -0700)]
iwlwifi: drop sw_crypto from hw_params.
Each HW supported by iwlwifi is capable of hardware crypto
so drop this flag from hw_params structure.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 19 Jun 2009 20:52:41 +0000 (13:52 -0700)]
iwlwifi: Check HW ready before prepare card.
Hardware may be ready for us to manage it without us trying to prepare
it first. Check if this is the case.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: differentiate quality reporting between legacy and HT configurations
We were not differentiating quality between legacy and HT
configurations. We change this to consider the differences.
New theory for reporting quality:
At a hardware RSSI of 45 you will be able to use MCS 7 reliably.
At a hardware RSSI of 45 you will be able to use MCS 15 reliably.
At a hardware RSSI of 35 you should be able use 54 Mbps reliably.
MCS 7 is the highets MCS index usable by a 1-stream device.
MCS 15 is the highest MCS index usable by a 2-stream device.
All ath9k devices are either 1-stream or 2-stream.
How many bars you see is derived from the qual reporting.
A more elaborate scheme can be used here but it requires tables
of SNR/throughput for each possible mode used. For the MCS table
you can refer to the wireless wiki:
Cc: Janath.Peiris@atheros.com Cc: Matt.Smith@atheros.com Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrey Yurovsky [Thu, 18 Jun 2009 02:15:19 +0000 (19:15 -0700)]
libertas: fix card cleanup order in SDIO driver
The SDIO driver sets the surpriseremoved flag before calling
lbs_remove_card. With IEEE PS enabled, lbs_remove_card must issue a
command to exit IEEE PS mode, however with that flag set the command
path is blocked and the card is never taken out of IEEE PS mode. This
step is required to ensure that the driver can be reloaded. This patch
moves the setting of surpriseremoved after lbs_remove_card is called.
Tested with V9 firmware by ensuring that IEEE PS is disabled when the
driver is removed. Reloading the driver is not fully tested due to a
separate issue with module reload in the SDIO driver, however this
patch at least leaves the card in a better state when we bring the
driver down.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrey Yurovsky [Thu, 18 Jun 2009 16:51:57 +0000 (09:51 -0700)]
libertas: correct card cleanup order in SPI driver
The SPI driver does a couple of card cleanup steps in the wrong order on
module removal. If IEEE PS is enabled, this results in the card being
left in IEEE PS mode and subsequent failures to reload the module. The
problem is that the surpriseremoved flag is set before calling
lbs_remove_card, but that function needs to issue a command to exit IEEE
PS mode (the flag blocks the command path). In addition, lbs_stop_card
should be called first because it clears out any pending commands.
Tested on a GSPI device with V9 firmware by confirming that we can
reload the module with or without IEEE PS enabled.
Also fix a warning from the wrong uint format in a printk.
V2: use z modifier, thanks Sebastian.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrey Yurovsky [Thu, 18 Jun 2009 01:45:34 +0000 (18:45 -0700)]
libertas: copy WPA keys to priv when associating
Libertas currently maintains a copy of the WPA unicast and group keys
when using WPA or WPA2. This copy is checked when deciding whether or
not to return to sleep in IEEE PS mode but the actual copying back to
priv was omitted, which breaks IEEE PS mode with WPA/WPA2 when one
issues commands that require temporarily keeping the device awake.
This patch introduces the omitted copy-back of the keys so that IEEE PS
functions correctly in WPA/WPA2 mode. Thanks to Dan Williams for
clearing up the issue.
V2: fix typo. Also, this has been tested on GSPI and SDIO with V9 firmware.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 6 Jul 2009 17:40:51 +0000 (19:40 +0200)]
cfg80211: fix giwrange
"cfg80211: Advertise ciphers via WE according to driver capability"
unfortunately broke iwrange -- it used the variable c
that needs to be 0 for the channel list.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 2 Jul 2009 19:26:45 +0000 (20:26 +0100)]
orinoco: fix printk format specifier for size_t arguments
This addresses the following compile warnings on 64-bit platforms.
drivers/net/wireless/orinoco/scan.c: In function 'orinoco_add_hostscan_results':
drivers/net/wireless/orinoco/scan.c:194: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/orinoco/scan.c:211: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/orinoco/scan.c:211: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 2 Jul 2009 16:26:18 +0000 (18:26 +0200)]
cfg80211: refuse authenticating to same BSSID twice
It is possible that there are different BSS structs with
the same BSSID, but we cannot authenticate with multiple
of them them because we need the BSSID to be unique for
deauthenticating/disassociating.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 2 Jul 2009 15:20:43 +0000 (17:20 +0200)]
cfg80211: keep track of BSSes
In order to avoid problems with BSS structs going away
while they're in use, I've long wanted to make cfg80211
keep track of them. Without the SME, that wasn't doable
but now that we have the SME we can do this too. It can
keep track of up to four separate authentications and
one association, regardless of whether it's controlled
by the cfg80211 SME or the userspace SME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 2 Jul 2009 13:49:03 +0000 (15:49 +0200)]
cfg80211: reset auth algorithm
When the interface is brought down, we need to
reset the auth algorithm because wpa_supplicant
doesn't reset it, and then we fail to use shared
key auth when required later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 2 Jul 2009 07:58:04 +0000 (09:58 +0200)]
cfg80211: send events for userspace SME
When the userspace SME is in control, we are currently not sending
events, but this means that any userspace applications using wext
or nl80211 to receive events will not know what's going on unless
they can also interpret the nl80211 assoc event. Since we have all
the required code, let the SME follow events from the userspace
SME, this even means that you will be refused to connect() while
the userspace SME is in control and connected.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:41:17 +0000 (21:41 +0200)]
mac80211: remove dead code, clean up
With mac80211 now always controlled by an external SME,
a lot of code is dead -- SSID, BSSID, channel selection
is always done externally, etc. Additionally, rename
IEEE80211_STA_TKIP_WEP_USED to IEEE80211_STA_DISABLE_11N
and clean up the code a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:40:45 +0000 (21:40 +0200)]
mac80211: remove auth algorithm retry
The automatic auth algorithm issue is now solved in
cfg80211, so mac80211 no longer needs code to try
different algorithms -- just using whatever cfg80211
asked for is good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:27:01 +0000 (21:27 +0200)]
mac80211: re-add HT disabling
The IEEE80211_STA_TKIP_WEP_USED flag is used internally to
disable HT when WEP or TKIP are used. Now that cfg80211 is
giving us the required information, we can set the flag
appropriately again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:27:00 +0000 (21:27 +0200)]
cfg80211: implement get_wireless_stats
By dropping the noise reporting, we can implement
wireless stats in cfg80211. We also make the
handler return NULL if we have no information,
which is possible thanks to the recent wext change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:59 +0000 (21:26 +0200)]
cfg80211: implement IWRATE
For now, let's implement that using a very hackish way:
simply mirror the wext API in the cfg80211 API. This
will have to be changed later when we implement proper
bitrate API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:57 +0000 (21:26 +0200)]
cfg80211: implement iwpower
Just on/off and timeout, and with a hacky cfg80211 method
until we figure out what we want, though this is probably
sufficient as we want to use pm_qos for wifi everywhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:56 +0000 (21:26 +0200)]
cfg80211: managed mode wext compatibility
This adds code to make it possible to use the cfg80211
connect() API with wireless extensions, and because the
previous patch added emulation of that API with auth()
and assoc(), by extension also supports wext on that.
At the same time, removes code from mac80211 for wext,
but doesn't yet clean up mac80211's mlme code more.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 2 Jul 2009 07:13:27 +0000 (09:13 +0200)]
cfg80211: emulate connect with auth/assoc
This adds code to cfg80211 so that drivers (mac80211 right
now) that don't implement connect but rather auth/assoc can
still be used with the nl80211 connect command. This will
also be necessary for the wext compat code.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Wed, 1 Jul 2009 19:26:54 +0000 (21:26 +0200)]
cfg80211: connect/disconnect API
This patch introduces the cfg80211 connect/disconnect API.
The goal here is to run the AUTH and ASSOC steps in one call.
This is needed for some fullmac cards that run both steps
directly from the target, after the host driver sends a
connect command.
Additionally, all the new crypto parameters for connect()
are now also valid for associate() -- although associate
requires the IEs to be used, the information can be useful
for drivers and should be given.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:51 +0000 (21:26 +0200)]
cfg80211: introduce nl80211 testmode command
This introduces a new NL80211_CMD_TESTMODE for testing
and calibration use with nl80211. There's no multiplexing
like like iwpriv had, and the command is not available by
default, it needs to be explicitly enabled in Kconfig and
shouldn't be enabled in most kernels.
The command requires a wiphy index or interface index to
identify the device to operate on, and the new TESTDATA
attribute. There also is API for sending replies to the
command, and testmode multicast messages (on a testmode
multicast group).
I've also updated mac80211 to be able to pass through the
command to the driver, since it itself doesn't implement
the testmode command.
Additionally, to give people an idea of how to use the
command, I've added a little code to hwsim that makes use
of the new command to set the powersave mode, this is
currently done via debugfs and should remain there, and
the testmode command only serves as an example of how to
use this best -- with nested netlink attributes in the
TESTDATA attribute. A hwsim testmode tool can be found at
http://git.sipsolutions.net/hwsim.git/. This tool is BSD
licensed so people can easily use it as a basis for their
own internal fabrication and validation tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:49 +0000 (21:26 +0200)]
mac80211: tell SME about real auth state
When the auth algorithm is rejected, but we don't have
another one to try, we will eventually retry but that
isn't useful -- we'll then do it again and again until
we eventually give up. Instead, we should let the SME
know and go into disabled state. The same applies for
situations where the AP rejects with any other status
code.
Additionally, when trying the next auth algorithm, we
should reset the auth_tries so that just a single lost
frame doesn't lead to us giving up on the third auth
algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:47 +0000 (21:26 +0200)]
cfg80211: use proper allocation flags
Instead of hardcoding GFP_ATOMIC everywhere, add a
new function parameter that gets the flags from the
caller. Obviously then I need to update all callers
(all of them in mac80211), and it turns out that now
it's ok to use GFP_KERNEL in almost all places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:45 +0000 (21:26 +0200)]
cfg80211: move break statement to correct place
Move a break statement to the correct place _after_ the
#endif, otherwise w/o WIRELESS_EXT things break badly.
Also, while touching this code, do a cleanup and assign
dev->ieee80211_ptr to a new variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:44 +0000 (21:26 +0200)]
wext: default to y
The way I initially thought we could do wireless extensions
is by making all the compat code in cfg80211 be independent
of CONFIG_WIRELESS_EXT, but this is turning out to not be
feasible. Therefore, fix the Kconfig help text and make the
option default to yes, so people won't get a nasty surprise
when mac80211 will get rid of its 'select WIRELESS_EXT' any
time now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:43 +0000 (21:26 +0200)]
mac80211: fix todo lock
The key todo lock can be taken from different locks
that require it to be _bh to avoid lock inversion
due to (soft)irqs.
This should fix the two problems reported by Bob and
Gabor:
http://mid.gmane.org/20090619113049.GB18956@hash.localnet
http://mid.gmane.org/4A3FA376.8020307@openwrt.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Bob Copeland <me@bobcopeland.com> Cc: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jul 2009 19:26:42 +0000 (21:26 +0200)]
wext: allow returning NULL stats
Currently, wext drivers cannot return NULL for stats even though
that would make the ioctl return -EOPNOTSUPP because that would
mean they are no longer listed in /proc/net/wireless. This patch
changes the wext core's behaviour to list them if they have any
wireless_handlers, but only show their stats when available, so
that drivers can start returning NULL if stats are currently not
available, reducing confusion for e.g. IBSS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 18 Jun 2009 22:21:26 +0000 (23:21 +0100)]
orinoco: initiate cfg80211 conversion
Initialise and register a wiphy.
Store the orinoco_private structure in the new wiphy, and use the
net_device private area to store the wireless_dev. This results in a
change to the way we navigate from a net_device to the driver private
orinoco_private, which we encapsulate in the inline function ndev_priv.
Most of the remaining calls to netdev_priv are thus replaced by
ndev_priv.
We can immediately rely on cfg80211 to handle SIOCGIWNAME, so
orinoco_ioctl_getname is removed.
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 18 Jun 2009 22:21:25 +0000 (23:21 +0100)]
orinoco: Change set_tkip to use orinoco_private instead of hermes_t
hw.h does not include hermes.h, and none of the other functions
requires types from that file. Also hermes_t is a (discouraged) typedef
so we can't add a forward declaration. Therefore change this function to
use orinoco_private.
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 18 Jun 2009 22:21:17 +0000 (23:21 +0100)]
cfg80211: infer WPA and WPA2 support from TKIP and CCMP
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 18 Jun 2009 22:21:16 +0000 (23:21 +0100)]
cfg80211: set WE encoding size based on available ciphers
Only set the sizes for WEP40 and WEP104.
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 18 Jun 2009 22:21:15 +0000 (23:21 +0100)]
cfg80211: allow drivers that can't scan for specific ssids
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 18 Jun 2009 22:21:14 +0000 (23:21 +0100)]
cfg80211: Advertise ciphers via WE according to driver capability
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 18 Jun 2009 22:21:13 +0000 (23:21 +0100)]
cfg80211: add wrapper function to get wiphy from priv pointer
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 18 Jun 2009 12:51:12 +0000 (14:51 +0200)]
mac80211_hwsim: clean up the skb before passing it back
We need to clean up the skb before we can copy it, this
is required for proper operation since the socket it is
still attached to could potentially live in a different
network namespace or so.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hin-Tak Leung [Thu, 18 Jun 2009 02:53:26 +0000 (03:53 +0100)]
zd1211rw: sort vid/pid pairs by numerical value
In the past ids were inserted in no particular order and it has
become hard to see what ids are already included or not. This
patch sorts the ids by numerical value and has no functional effect.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log