Venkat Subbiah [Tue, 4 Oct 2011 00:22:04 +0000 (17:22 -0700)]
watchdog: Octeon: Mark octeon_wdt interrupt as IRQF_NO_THREAD
This is to exclude it from force threading to allow RT patch set to work.
The watchdog timers are per-CPU and the addresses of register that reset
the timer are calculated based on the current CPU. Therefore we cannot
allow it to run on a thread on a different CPU. Also we only do a
single register write, which is much faster than scheduling a handler
thread.
And while on this line remove IRQF_DISABLED as this flag is a NOP.
Signed-off-by: Venkat Subbiah<venkat.subbiah@cavium.com> Acked-by: David Daney<david.daney@cavium.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Fri, 14 Oct 2011 05:06:39 +0000 (17:06 +1200)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: revert to using a kthread for AIL pushing
xfs: force the log if we encounter pinned buffers in .iop_pushbuf
xfs: do not update xa_last_pushed_lsn for locked items
Mika Westerberg [Thu, 13 Oct 2011 09:04:20 +0000 (12:04 +0300)]
x86, mrst: use a temporary variable for SFI irq
SFI tables reside in RAM and should not be modified once they are
written. Current code went to set pentry->irq to zero which causes
subsequent reads to fail with invalid SFI table checksum. This will
break kexec as the second kernel fails to validate SFI tables.
To fix this we use temporary variable for irq number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The w83627ehf driver is improperly reporting thermal diode sensors as
type 2, instead of 3. This caused "sensors" and possibly other
monitoring tools to report these sensors as "transistor" instead of
"thermal diode".
Furthermore, diode subtype selection (CPU vs. external) is only
supported by the original W83627EHF/EHG. All later models only support
CPU diode type, and some (NCT6776F) don't even have the register in
question so we should avoid reading from it.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Hartmut Knaack [Mon, 10 Oct 2011 22:22:45 +0000 (00:22 +0200)]
gpio-pca953x: fix gpio_base
gpio_base was set to 0 if no system platform data or open firmware
platform data was provided. This led to conflicts, if any other gpiochip
with a gpiobase of 0 was instantiated already. Setting it to -1 will
automatically use the first one available.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
gpio/omap: fix build error with certain OMAP1 configs
With commit f64ad1a0e21a, "gpio/omap: cleanup _set_gpio_wakeup(), remove
ifdefs", access to build time conditionally omitted 'suspend_wakeup'
member of the 'gpio_bank' structure has been placed unconditionally in
function _set_gpio_wakeup(), which is always built. This resulted in the
driver compilation broken for certain OMAP1, i.e., non-OMAP16xx,
configurations.
Really required or not in previously excluded cases, define this
structure member unconditionally as a fix.
Tested with a custom OMAP1510 only configuration.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by: Kevin Hilman <khilman@ti.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Chris Metcalf [Wed, 5 Oct 2011 21:09:29 +0000 (17:09 -0400)]
tile: revert change from <asm/atomic.h> to <linux/atomic.h> in asm files
The 32-bit TILEPro support uses some #defines in <asm/atomic_32.h>
for atomic support routines in assembly. To make this more explicit,
I've turned those includes into includes of <asm/atomic_32.h>, which
should hopefully make it clear that they shouldn't be bombed into
<linux/atomic.h> in any cleanups.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
mscan: too much data copied to CAN frame due to 16 bit accesses
gro: refetch inet6_protos[] after pulling ext headers
bnx2x: fix cl_id allocation for non-eth clients for NPAR mode
mlx4_en: fix endianness with blue frame support
There are a lot of file references to now moved or deleted files in the
whole tree, especially in documentation and Kconfig files. This patch
fixes the references in drivers/ide/.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have a few issues with the way the workqueue code is used to
implement AIL pushing:
- it accidentally uses the same workqueue as the syncer action, and thus
can be prevented from running if there are enough sync actions active
in the system.
- it doesn't use the HIGHPRI flag to queue at the head of the queue of
work items
At this point I'm not confident enough in getting all the workqueue flags and
tweaks right to provide a perfectly reliable execution context for AIL
pushing, which is the most important piece in XFS to make forward progress
when the log fills.
Revert back to use a kthread per filesystem which fixes all the above issues
at the cost of having a task struct and stack around for each mounted
filesystem. In addition this also gives us much better ways to diagnose
any issues involving hung AIL pushing and removes a small amount of code.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Stefan Priebe <s.priebe@profihost.ag> Tested-by: Stefan Priebe <s.priebe@profihost.ag> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Alex Elder <aelder@sgi.com>
xfs: force the log if we encounter pinned buffers in .iop_pushbuf
We need to check for pinned buffers even in .iop_pushbuf given that inode
items flush into the same buffers that may be pinned directly due operations
on the unlinked inode list operating directly on buffers. To do this add a
return value to .iop_pushbuf that tells the AIL push about this and use
the existing log force mechanisms to unpin it.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Stefan Priebe <s.priebe@profihost.ag> Tested-by: Stefan Priebe <s.priebe@profihost.ag> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Alex Elder <aelder@sgi.com>
xfs: do not update xa_last_pushed_lsn for locked items
If an item was locked we should not update xa_last_pushed_lsn and thus skip
it when restarting the AIL scan as we need to be able to lock and write it
out as soon as possible. Otherwise heavy lock contention might starve AIL
pushing too easily, especially given the larger backoff once we moved
xa_last_pushed_lsn all the way to the target lsn.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Stefan Priebe <s.priebe@profihost.ag> Tested-by: Stefan Priebe <s.priebe@profihost.ag> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Alex Elder <aelder@sgi.com>
Chris Mason [Tue, 11 Oct 2011 15:41:40 +0000 (11:41 -0400)]
Btrfs: make sure not to defrag extents past i_size
The btrfs file defrag code will loop through the extents and
force COW on them. But there is a concurrent truncate in the middle of
the defrag, it might end up defragging the same range over and over
again.
The problem is that writepage won't go through and do anything on pages
past i_size, so the cow won't happen, so the file will appear to still
be fragmented. defrag will end up hitting the same extents again and
again.
In the worst case, the truncate can actually live lock with the defrag
because the defrag keeps creating new ordered extents which the truncate
code keeps waiting on.
The fix here is to make defrag check for i_size inside the main loop,
instead of just once before the looping starts.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Is caused by commit 3ae36655 ("x86-64: Rework vsyscall emulation and add
vsyscall= parameter") - the vsyscall emulation code is not fully cooked
yet as UML relies on some rather fragile SIGSEGV semantics.
Linus suggested in https://lkml.org/lkml/2011/8/9/376 to default
to vsyscall=native for now, this patch implements that.
and then it'll go into a loop: writeback -> defrag -> writeback ...
It's because writeback writes [8K, 200K] and then writes [0, 8K].
I tried to make writeback know if the pages are dirtied by defrag,
but the patch was a bit intrusive. Here I simply set writeback_index
when we defrag a file.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
mscan: too much data copied to CAN frame due to 16 bit accesses
Due to the 16 bit access to mscan registers there's too much data copied to
the zero initialized CAN frame when having an odd number of bytes to copy.
This patch ensures that only the requested bytes are copied by using an
8 bit access for the remaining byte.
Reported-by: Andre Naujoks <nautsch@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 9 Oct 2011 23:57:36 +0000 (23:57 +0000)]
bnx2x: fix cl_id allocation for non-eth clients for NPAR mode
There are some consolidations of NPAR configuration
when FCoE and iSCSI L2 clients will get the same id,
in this case FCoE ring will be non-functional.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The doorbell register was being unconditionally swapped. In x86, that
meant it was being swapped to BE and written to the descriptor and to
memory, depending on the case of blue frame support or writing to
doorbell register. On PPC, this meant it was being swapped to LE and
then swapped back to BE while writing to the register. But in the blue
frame case, it was being written as LE to the descriptor.
The fix is not to swap doorbell unconditionally, write it to the
register as BE and convert it to BE when writing it to the descriptor.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Reported-by: Richard Hendrickson <richhend@us.ibm.com> Cc: Eli Cohen <eli@dev.mellanox.co.il> Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 10 Oct 2011 02:48:27 +0000 (14:48 +1200)]
Merge branch 'fixes' of git://git.linaro.org/people/arnd/arm-soc
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
ARM: mach-ux500: enable fix for ARM errata 754322
ARM: OMAP: musb: Remove a redundant omap4430_phy_init call in usb_musb_init
ARM: OMAP: Fix i2c init for twl4030
ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1
Marc Dietrich [Fri, 7 Oct 2011 15:31:41 +0000 (08:31 -0700)]
ARM: tegra: fix compilation error due to mach/hardware.h removal
This fixes a compilation error in cpu-tegra.c which was introduced in dc8d966bccde ("ARM: convert PCI defines to variables") which removed the
now obsolete mach/hardware.h from the mach-tegra subtree.
Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Olof Johansson <olof@lixom.net> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 10 Oct 2011 02:43:06 +0000 (14:43 +1200)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: use hardcoded dig encoder to transmitter mapping for DCE4.1
drm/radeon/kms: fix dp_detect handling for DP bridge chips
drm/radeon/kms: retry aux transactions if there are status flags
Olof Johansson [Fri, 7 Oct 2011 20:27:48 +0000 (13:27 -0700)]
MAINTAINERS: Update tegra maintainer information
A couple of changes to the Tegra maintainership setup:
I'm very glad to bring on Stephen Warren on board as a maintainer. The
work he has done so far is excellent, and the fact that he works for
Nvidia means he has long-term interest in the platform.
Erik Gilling did an astounding amount of work on getting things up and
running but has been a silent partner on the maintainership side for a
while, and is stepping down. Thanks for your contributions so far, Erik.
Finally, update the git URL since I'll take over running the main repo
for a while.
Overall maintainership model isn't changing much at this time: We'll all
three review patches as appropriate, and one of us will collect the main
repo (me at this time).
Signed-off-by: Olof Johansson <olof@lixom.net> Cc: Erik Gilling <konkers@android.com> Acked-by: Colin Cross <ccross@android.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 10 Oct 2011 02:39:03 +0000 (14:39 +1200)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (29 commits)
MIPS: Call oops_enter, oops_exit in die
staging/octeon: Software should check the checksum of no tcp/udp packets
MIPS: Octeon: Enable C0_UserLocal probing.
MIPS: No branches in delay slots for huge pages in handle_tlbl
MIPS: Don't clobber CP0_STATUS value for CONFIG_MIPS_MT_SMTC
MIPS: Octeon: Select CONFIG_HOLES_IN_ZONE
MIPS: PM: Use struct syscore_ops instead of sysdevs for PM (v2)
MIPS: Compat: Use 32-bit wrapper for compat_sys_futex.
MIPS: Do not use EXTRA_CFLAGS
MIPS: Alchemy: DB1200: Disable cascade IRQ in handler
SERIAL: Lantiq: Set timeout in uart_port
MIPS: Lantiq: Fix setting the PCI bus speed on AR9
MIPS: Lantiq: Fix external interrupt sources
MIPS: tlbex: Fix build error in R3000 code.
MIPS: Alchemy: Include Au1100 in PM code.
MIPS: Alchemy: Fix typo in MAC0 registration
MIPS: MSP71xx: Fix build error.
MIPS: Handle __put_user() sleeping.
MIPS: Allow forced irq threading
MIPS: i8259: Mark cascade interrupt non-threaded
...
Steve French [Fri, 7 Oct 2011 04:14:07 +0000 (23:14 -0500)]
[CIFS] Fix first time message on mount, ntlmv2 upgrade delayed to 3.2
Microsoft has a bug with ntlmv2 that requires use of ntlmssp, but
we didn't get the required information on when/how to use ntlmssp to
old (but once very popular) legacy servers (various NT4 fixpacks
for example) until too late to merge for 3.1. Will upgrade
to NTLMv2 in NTLMSSP in 3.2
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com>
Linus Torvalds [Thu, 6 Oct 2011 23:15:10 +0000 (16:15 -0700)]
Merge git://github.com/davem330/net
* git://github.com/davem330/net:
net: fix typos in Documentation/networking/scaling.txt
bridge: leave carrier on for empty bridge
netfilter: Use proper rwlock init function
tcp: properly update lost_cnt_hint during shifting
tcp: properly handle md5sig_pool references
macvlan/macvtap: Fix unicast between macvtap interfaces in bridge mode
Paul Menzel [Wed, 31 Aug 2011 15:07:10 +0000 (17:07 +0200)]
x86/PCI: use host bridge _CRS info on ASUS M2V-MX SE
In summary, this DMI quirk uses the _CRS info by default for the ASUS
M2V-MX SE by turning on `pci=use_crs` and is similar to the quirk
added by commit 2491762cfb47 ("x86/PCI: use host bridge _CRS info on
ASRock ALiveSATA2-GLAN") whose commit message should be read for further
information.
Since commit 3e3da00c01d0 ("x86/pci: AMD one chain system to use pci
read out res") Linux gives the following oops:
Trusting the ACPI _CRS information (`pci=use_crs`) fixes this problem.
$ dmesg | grep -i crs # with the quirk
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
The match has to be against the DMI board entries though since the vendor entries are not populated.
DMI: System manufacturer System Product Name/M2V-MX SE, BIOS 0304 10/30/2007
This quirk should be removed when `pci=use_crs` is enabled for machines
from 2006 or earlier or some other solution is implemented.
Using coreboot [1] with this board the problem does not exist but this
quirk also does not affect it either. To be safe though the check is
tightened to only take effect when the BIOS from American Megatrends is
used.
15:13 < ruik> but coreboot does not need that
15:13 < ruik> because i have there only one root bus
15:13 < ruik> the audio is behind a bridge
$ sudo dmidecode
BIOS Information
Vendor: American Megatrends Inc.
Version: 0304
Release Date: 10/30/2007
This resolves a regression seen by some users of bridging.
Some users use the bridge like a dummy device.
They expect to be able to put an IPv6 address on the device
with no ports attached. Although there are better ways of doing
this, there is no reason to not allow it.
Note: the bridge still will reflect the state of ports in the
bridge if there are any added.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Gleixner [Wed, 5 Oct 2011 03:24:43 +0000 (03:24 +0000)]
netfilter: Use proper rwlock init function
Replace the open coded initialization with the init function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://bedivere.hansenpartnership.com/git/scsi-rc-fixes-2.6:
[SCSI] libsas: fix panic when single phy is disabled on a wide port
[SCSI] qla2xxx: Fix crash in qla2x00_abort_all_cmds() on unload
Alex Deucher [Tue, 4 Oct 2011 16:23:24 +0000 (12:23 -0400)]
drm/radeon/kms: fix dp_detect handling for DP bridge chips
The HPD pin is not reliable for detecting whether a monitor
is connected or not. Skip HPD and just use DDC or load
detection.
Fixes phantom VGA connected bugs.
[Michel: fixes phantom VGA bugs on his llano system.]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Tested-by: Michel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 4 Oct 2011 21:23:15 +0000 (17:23 -0400)]
drm/radeon/kms: retry aux transactions if there are status flags
If there are error flags in the aux status, retry the transaction.
This makes aux much more reliable, especially on llano systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Yan, Zheng [Sun, 2 Oct 2011 04:21:50 +0000 (04:21 +0000)]
tcp: properly update lost_cnt_hint during shifting
lost_skb_hint is used by tcp_mark_head_lost() to mark the first unhandled skb.
lost_cnt_hint is the number of packets or sacked packets before the lost_skb_hint;
When shifting a skb that is before the lost_skb_hint, if tcp_is_fack() is ture,
the skb has already been counted in the lost_cnt_hint; if tcp_is_fack() is false,
tcp_sacktag_one() will increase the lost_cnt_hint. So tcp_shifted_skb() does not
need to adjust the lost_cnt_hint by itself. When shifting a skb that is equal to
lost_skb_hint, the shifted packets will not be counted by tcp_mark_head_lost().
So tcp_shifted_skb() should adjust the lost_cnt_hint even tcp_is_fack(tp) is true.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v4_clear_md5_list() assumes that multiple tcp md5sig peers
only hold one reference to md5sig_pool. but tcp_v4_md5_do_add()
increases use count of md5sig_pool for each peer. This patch
makes tcp_v4_md5_do_add() only increases use count for the first
tcp md5sig peer.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ward [Sun, 18 Sep 2011 12:53:20 +0000 (12:53 +0000)]
macvlan/macvtap: Fix unicast between macvtap interfaces in bridge mode
Packets should always be forwarded to the lowerdev using dev_forward_skb.
vlan->forward is for packets being forwarded directly to another macvlan/
macvtap device (used for multicast in bridge mode).
Reported-and-tested-by: Shlomo Pongratz <shlomop@mellanox.com> Signed-off-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 4 Oct 2011 17:37:06 +0000 (10:37 -0700)]
Merge git://github.com/davem330/net
* git://github.com/davem330/net:
pch_gbe: Fixed the issue on which a network freezes
pch_gbe: Fixed the issue on which PC was frozen when link was downed.
make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
net: xen-netback: correctly restart Tx after a VM restore/migrate
bonding: properly stop queuing work when requested
can bcm: fix incomplete tx_setup fix
RDSRDMA: Fix cleanup of rds_iw_mr_pool
net: Documentation: Fix type of variables
ibmveth: Fix oops on request_irq failure
ipv6: nullify ipv6_ac_list and ipv6_fl_list when creating new socket
cxgb4: Fix EEH on IBM P7IOC
can bcm: fix tx_setup off-by-one errors
MAINTAINERS: tehuti: Alexander Indenbaum's address bounces
dp83640: reduce driver noise
ptp: fix L2 event message recognition
Linus Torvalds [Tue, 4 Oct 2011 16:59:22 +0000 (09:59 -0700)]
Merge branch 'fix/asoc' of git://github.com/tiwai/sound
* 'fix/asoc' of git://github.com/tiwai/sound:
ASoC: omap_mcpdm_remove cannot be __devexit
ASoC: Fix setting update bits for WM8753_LADC and WM8753_RADC
ASoC: use a valid device for dev_err() in Zylonite
Jon Mason [Mon, 3 Oct 2011 14:50:20 +0000 (09:50 -0500)]
PCI: Disable MPS configuration by default
Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults. Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.
Also, add the option for peer to peer DMA MPS configuration. Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another. To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: Jon Mason <mason@myri.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Deucher [Tue, 4 Oct 2011 14:46:34 +0000 (10:46 -0400)]
drm/radeon/kms: fix channel_remap setup (v2)
Most asics just use the hw default value which requires
no explicit programming. For those that need a different
value, the vbios will program it properly. As such,
there's no need to program these registers explicitly
in the driver. Changing MC_SHARED_CHREMAP requires a reload
of all data in vram otherwise its contents will be scambled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
We found that adding load, Rx data sometimes drops.(with DMA transfer mode)
The cause is that before starting Rx-DMA processing, Tx-DMA processing starts.
This causes FIFO overrun occurs.
This patch fixes the issue by modifying FIFO tx-threshold and DMA descriptor
size like below.
Current this patch
Rx-descriptor 4Byte+12Byte*341 --> 12Byte*340-4Byte-12Byte
Rx-threshold (Not modified)
Tx-descriptor 4Byte+12Byte*341 --> 16Byte-12Byte*340
Rx-threshold 12Byte --> 2Byte
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi-topcliff-pch: add tx-memory clear after complete transmitting
Currently, in case of reading date from SPI flash,
command is sent twice.
The cause is that tx-memory clear processing is missing .
This patch adds the tx-momory clear processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Takashi Iwai [Tue, 4 Oct 2011 01:09:14 +0000 (18:09 -0700)]
lis3: fix regression of HP DriveGuard with 8bit chip
Commit 2a7fade7e03 ("hwmon: lis3: Power on corrections") caused a
regression on HP laptops with 8bit chip. Writing CTRL2_BOOT_8B bit seems
clearing the BIOS setup, and no proper interrupt for DriveGuard will be
triggered any more.
Since the init code there is basically only for embedded devices, put a
pdata check so that the problematic initialization will be skipped for
hp_accel stuff.
Borislav Petkov [Mon, 3 Oct 2011 18:28:18 +0000 (14:28 -0400)]
ide-disk: Fix request requeuing
Simon Kirby reported that on his RAID setup with idedisk underneath
the box OOMs after a couple of days of runtime. Running with
CONFIG_DEBUG_KMEMLEAK pointed to idedisk_prep_fn() which unconditionally
allocates an ide_cmd struct. However, ide_requeue_and_plug() can be
called more than once per request, either from the request issue or the
IRQ handler path and do blk_peek_request() ends up in idedisk_prep_fn()
repeatedly, allocating a struct ide_cmd everytime and "forgetting" the
previous pointer.
Make sure the code reuses the old allocated chunk.
pch_gbe: Fixed the issue on which a network freezes
The pch_gbe driver has an issue which a network stops,
when receiving traffic is high.
In the case, The link down and up are necessary to return a network.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 30 Sep 2011 10:38:28 +0000 (10:38 +0000)]
make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
This is a minor change.
Up until kernel 2.6.32, getsockopt(fd, SOL_PACKET, PACKET_STATISTICS,
...) would return total and dropped packets since its last invocation. The
introduction of socket queue overflow reporting [1] changed drop
rate calculation in the normal packet socket path, but not when using a
packet ring. As a result, the getsockopt now returns different statistics
depending on the reception method used. With a ring, it still returns the
count since the last call, as counts are incremented in tpacket_rcv and
reset in getsockopt. Without a ring, it returns 0 if no drops occurred
since the last getsockopt and the total drops over the lifespan of
the socket otherwise. The culprit is this line in packet_rcv, executed
on a drop:
As it shows, the new drop number it taken from the socket drop counter,
which is not reset at getsockopt. I put together a small example
that demonstrates the issue [2]. It runs for 10 seconds and overflows
the queue/ring on every odd second. The reported drop rates are:
ring: 16, 0, 16, 0, 16, ...
non-ring: 0, 15, 0, 30, 0, 46, 0, 60, 0 , 74.
Note how the even ring counts monotonically increase. Because the
getsockopt adds tp_drops to tp_packets, total counts are similarly
reported cumulatively. Long story short, reinstating the original code, as
the below patch does, fixes the issue at the cost of additional per-packet
cycles. Another solution that does not introduce per-packet overhead
is be to keep the current data path, record the value of sk_drops at
getsockopt() at call N in a new field in struct packetsock and subtract
that when reporting at call N+1. I'll be happy to code that, instead,
it's just more messy.
David Vrabel [Fri, 30 Sep 2011 06:37:51 +0000 (06:37 +0000)]
net: xen-netback: correctly restart Tx after a VM restore/migrate
If a VM is saved and restored (or migrated) the netback driver will no
longer process any Tx packets from the frontend. xenvif_up() does not
schedule the processing of any pending Tx requests from the front end
because the carrier is off. Without this initial kick the frontend
just adds Tx requests to the ring without raising an event (until the
ring is full).
This was caused by 47103041e91794acdbc6165da0ae288d844c820b (net:
xen-netback: convert to hw_features) which reordered the calls to
xenvif_up() and netif_carrier_on() in xenvif_connect().
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Fri, 23 Sep 2011 10:53:34 +0000 (10:53 +0000)]
bonding: properly stop queuing work when requested
During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed. I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.
There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first. There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.
This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set. I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Reported-by: Liang Zheng <lzheng@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michel Dänzer [Fri, 30 Sep 2011 15:16:53 +0000 (17:16 +0200)]
drm/radeon: Set cursor x/y to 0 when x/yorigin > 0.
Apart from the obvious cleanup, this should make the line
cursor_end = x - xorigin + w;
correct now.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Fri, 30 Sep 2011 15:16:52 +0000 (17:16 +0200)]
drm/radeon: Update AVIVO cursor coordinate origin before x/yorigin calculation.
Fixes cursor disappearing prematurely when moving off a top/left edge which
is not located at the desktop top/left edge.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Nicholas Miell <nmiell@gmail.com> Reviewed-by: Michel Dänzer <michel@daenzer.net> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Mon, 3 Oct 2011 13:13:46 +0000 (09:13 -0400)]
drm/radeon/kms: add retry limits for native DP aux defer
The previous code could potentially loop forever. Limit
the number of DP aux defer retries to 4 for native aux
transactions, same as i2c over aux transactions.
Alex Deucher [Mon, 3 Oct 2011 13:13:45 +0000 (09:13 -0400)]
drm/radeon/kms: fix regression in DP aux defer handling
An incorrect ordering in the error checking code lead
to DP aux defer being skipped in the aux native write
path. Move the bytes transferred check (ret == 0)
below the defer check.
Tracked down by: Brad Campbell <brad@fnarfbargle.com>
The following patch is admittedly a band-aid, and does not solve the
root cause, but it still is a good candidate for hardening as a pointer
check before reference.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com> Tested-by: Jack Wang <jack_wang@usish.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Roland Dreier [Thu, 22 Sep 2011 07:06:05 +0000 (00:06 -0700)]
[SCSI] qla2xxx: Fix crash in qla2x00_abort_all_cmds() on unload
I hit a crash in qla2x00_abort_all_cmds() if the qla2xxx module is
unloaded right after it is loaded. I debugged this down to the abort
handling improperly treating a command of type SRB_ADISC_CMD as if it
had a bsg_job to complete when that command actually uses the iocb_cmd
part of the union. (I guess to hit this one has to unload the module
while the async FC initialization is still in progress)
It seems we should only look for a bsg_job if type is SRB_ELS_CMD_RPT,
SRB_ELS_CMD_HST or SRB_CT_CMD, so switch the test to make that explicit.
Signed-off-by: Roland Dreier <roland@purestorage.com> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Sat, 1 Oct 2011 15:37:25 +0000 (08:37 -0700)]
Merge branches 'irq-urgent-for-linus', 'x86-urgent-for-linus' and 'sched-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip
* 'irq-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
irq: Fix check for already initialized irq_domain in irq_domain_add
irq: Add declaration of irq_domain_simple_ops to irqdomain.h
* 'x86-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86/rtc: Don't recursively acquire rtc_lock
* 'sched-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
posix-cpu-timers: Cure SMP wobbles
sched: Fix up wchan borkage
sched/rt: Migrate equal priority tasks to available CPUs
Josef Bacik [Fri, 30 Sep 2011 19:23:54 +0000 (15:23 -0400)]
Btrfs: force a page fault if we have a shorty copy on a page boundary
A user reported a problem where ceph was getting into 100% cpu usage while doing
some writing. It turns out it's because we were doing a short write on a not
uptodate page, which means we'd fall back at one page at a time and fault the
page in. The problem is our position is on the page boundary, so our fault in
logic wasn't actually reading the page, so we'd just spin forever or until the
page got read in by somebody else. This will force a readpage if we end up
doing a short copy. Alexandre could reproduce this easily with ceph and reports
it fixes his problem. I also wrote a reproducer that no longer hangs my box
with this patch. Thanks,
Reported-and-tested-by: Alexandre Oliva <aoliva@redhat.com> Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Axel Lin [Fri, 30 Sep 2011 18:05:55 +0000 (11:05 -0700)]
ARM: OMAP: musb: Remove a redundant omap4430_phy_init call in usb_musb_init
Current code calls omap4430_phy_init() twice in usb_musb_init().
Calling omap4430_phy_init() once is enough.
This patch removes the first omap4430_phy_init() call, which using an
uninitialized pointer as parameter.
This patch elimates below build warning:
arch/arm/mach-omap2/usb-musb.c: In function 'usb_musb_init':
arch/arm/mach-omap2/usb-musb.c:141: warning: 'dev' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Bjarne Steinsbo <bsteinsbo@gmail.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Fri, 30 Sep 2011 18:05:55 +0000 (11:05 -0700)]
ARM: OMAP: Fix i2c init for twl4030
Looks like 2600 kHz rate does not work reliably on 2430,
so just use the 100 kHz rate.
Otherwise the system often fails to boot properly with:
omap_i2c omap_i2c.2: timeout waiting for bus ready
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
twl: clock init err [-110]
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
TWL4030 Unable to unlock IDCODE registers --110
ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1
Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for
MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance
with the control module programming guide. This fixes a bug where if trying to
use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be
affected by a changing SDMMC1_VDDS.
Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever
SDMMC1_VDDS ramps up/down or changes for cell protection purposes.
MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore
they can operate independently.
Signed-off-by: Bryan Buckley <bryan.buckley@ti.com> Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Tested-by: Balaji T K <balajitk@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Zijlstra [Thu, 1 Sep 2011 10:42:04 +0000 (12:42 +0200)]
posix-cpu-timers: Cure SMP wobbles
David reported:
Attached below is a watered-down version of rt/tst-cpuclock2.c from
GLIBC. Just build it with "gcc -o test test.c -lpthread -lrt" or
similar.
Run it several times, and you will see cases where the main thread
will measure a process clock difference before and after the nanosleep
which is smaller than the cpu-burner thread's individual thread clock
difference. This doesn't make any sense since the cpu-burner thread
is part of the top-level process's thread group.
I've reproduced this on both x86-64 and sparc64 (using both 32-bit and
64-bit binaries).
The diff of 'process' should always be >= the diff of 'thread'.
I make sure to wrap the 'thread' clock measurements the most tightly
around the nanosleep() call, and that the 'process' clock measurements
are the outer-most ones.
This is due to us using p->se.sum_exec_runtime in
thread_group_cputime() where we iterate the thread group and sum all
data. This does not take time since the last schedule operation (tick
or otherwise) into account. We can cure this by using
task_sched_runtime() at the cost of having to take locks.
This also means we can (and must) do away with
thread_group_sched_runtime() since the modified thread_group_cputime()
is now more accurate and would deadlock when called from
thread_group_sched_runtime().
Aside of that it makes the function safe on 32 bit systems. The old
code added t->se.sum_exec_runtime unprotected. sum_exec_runtime is a
64bit value and could be changed on another cpu at the same time.
Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: stable@kernel.org Link: http://lkml.kernel.org/r/1314874459.7945.22.camel@twins Tested-by: David Miller <davem@davemloft.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ALSA: hda - Fix a regression of the position-buffer check
The commit a810364a0424c297242c6c66071a42f7675a5568
ALSA: hda - Handle -1 as invalid position, too
caused a regression on some machines that require the position-buffer
instead of LPIB, e.g. resulting in noises with mic recording with
PulseAudio.
This patch fixes the detection by delaying the test at the timing as
same as 3.0, i.e. doing the position check only when requested in
azx_position_ok().
projects / karo-tx-linux.git / log