Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.
Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.
Note that this replaces the commit fe5fb2e3b58f ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Dan O'Donovan <dan@emutex.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit d94a461d7a7d ("ath9k: use ieee80211_tx_status_noskb
where possible") the driver uses rcu_read_lock() && rcu_read_unlock(), yet on
returning early in ath_tx_edma_tasklet() the unlock is missing leading to stalls
and suspicious RCU usage:
Signed-off-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de> Fixes: d94a461d7a7d ("ath9k: use ieee80211_tx_status_noskb where possible") Acked-by: Felix Fietkau <nbd@nbd.name> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The active_high LED of my Wistron DNMA-92 is still being recognized as
active_low on 4.7.6 mainline. When I was preparing my former commit 0f9edcdd88a9 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92
cards.") to fix that I must have somehow messed up with testing, because
I tested the final version of that patch before sending it, and it was
apparently working; but now it is not working on 4.7.6 mainline.
I initially added the PCI_DEVICE_SUB section for 0x0029/0x2096 above the
PCI_VDEVICE section for 0x0029; but then I moved the former below the
latter after seeing how 0x002A sections were sorted in the file.
This turned out to be wrong: if a generic PCI_VDEVICE entry (that has
both subvendor and subdevice IDs set to PCI_ANY_ID) is put before a more
specific one (PCI_DEVICE_SUB), then the generic PCI_VDEVICE entry will
match first and will be used.
With this patch, 0x0029/0x2096 has finally got active_high LED on 4.7.6.
While I'm at it, let's fix 0x002A too by also moving its generic definition
below its specific ones.
Fixes: 0f9edcdd88a9 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.") Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
[kvalo@qca.qualcomm.com: improve the commit log based on email discussions] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b2d70d4944c1 ("ath9k: make GPIO API to support both of WMAC and
SOC") refactored ath9k_hw_gpio_get() to support both WMAC and SOC GPIOs,
changing the return on success from 1 to BIT(gpio). This broke some callers
like ath_is_rfkill_set(). This doesn't fix any known bug in mainline at the
moment, but should be fixed anyway.
Instead of fixing all callers, change ath9k_hw_gpio_get() back to only
return 0 or 1.
Fixes: b2d70d4944c1 ("ath9k: make GPIO API to support both of WMAC and SOC") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
[kvalo@qca.qualcomm.com: mention that doesn't fix any known bug] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The H2C MEDIA_STATUS_RPT command for some reason causes 8192eu and
8723bu devices not being able to reconnect.
Reported-by: Barry Day <briselec@gmail.com> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'perf report --tui' exits with error when it finds a sample of zero
length symbol (i.e. addr == sym->start == sym->end). Actually these are
valid samples. Don't exit TUI and show report with such symbols.
Reported-and-Tested-by: Anton Blanchard <anton@samba.org> Link: https://lkml.org/lkml/2016/10/8/189 Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Chris Riyder <chris.ryder@arm.com> Cc: linuxppc-dev@lists.ozlabs.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1479804050-5028-1-git-send-email-ravi.bangoria@linux.vnet.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An earlier patch allowed enabling PT and LBR at the same
time on Goldmont. However it also allowed enabling BTS and LBR
at the same time, which is still not supported. Fix this by
bypassing the check only for PT.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: alexander.shishkin@intel.com Cc: kan.liang@intel.com Fixes: ccbebba4c6bf ("perf/x86/intel/pt: Bypass PT vs. LBR exclusivity if the core supports it") Link: http://lkml.kernel.org/r/20161209001417.4713-1-andi@firstfloor.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit a5ffbe0a1993 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Reported-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f28 ("ath10k: implement NAPI support") Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is a CRC error in the SPROM read from the device, the code
attempts to handle a fallback SPROM. When this also fails, the driver
returns zero rather than an error code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4efca4ed ("kbuild: modversions for EXPORT_SYMBOL() for asm") adds
modversion support for symbols exported from asm files. Architectures
must include C-style declarations for those symbols in asm/asm-prototypes.h
in order for them to be versioned.
Add these declarations for x86, and an architecture-independent file that
can be used for common symbols.
With f27c2f6 reverting 8ab2ae6 ("default exported asm symbols to zero") we
produce a scary warning on x86, this commit fixes that.
Signed-off-by: Adam Borowski <kilobyte@angband.pl> Tested-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Nicholas Piggin <npiggin@gmail.com> Tested-by: Peter Wu <peter@lekensteyn.nl> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both Debian and kernel archs are "arm64" but UTS_MACHINE and gcc say
"aarch64". Recognizing just the latter should be enough but let's
accept both in case something regresses again or an user sets
UTS_MACHINE=arm64.
Regressed in cfa88c7: arm64: Set UTS_MACHINE in the Makefile.
Signed-off-by: Adam Borowski <kilobyte@angband.pl> Acked-by: Riku Voipio <riku.voipio@linaro.org> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xlog_recover_clear_agi_bucket didn't set the
type to XFS_BLFT_AGI_BUF, so we got a warning during log
replay (or an ASSERT on a debug build).
XFS (md0): Unknown buffer type 0!
XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1
Fix this, as was done in f19b872b for 2 other locations
with the same problem.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been several reports over the years of NULL pointer
dereferences in xfs_trans_log_inode during xfs_fsr processes,
when the process is doing an fput and tearing down extents
on the temporary inode, something like:
As it turns out, this is because the i_itemp pointer, along
with the d_ops pointer, has been overwritten with zeros
when we tear down the extents during truncate. When the in-core
inode fork on the temporary inode used by xfs_fsr was originally
set up during the extent swap, we mistakenly looked at di_nextents
to determine whether all extents fit inline, but this misses extents
generated by speculative preallocation; we should be using if_bytes
instead.
This mistake corrupts the in-memory inode, and code in
xfs_iext_remove_inline eventually gets bad inputs, causing
it to memmove and memset incorrect ranges; this became apparent
because the two values in ifp->if_u2.if_inline_ext[1] contained
what should have been in d_ops and i_itemp; they were memmoved due
to incorrect array indexing and then the original locations
were zeroed with memset, again due to an array overrun.
Fix this by properly using i_df.if_bytes to determine the number
of extents, not di_nextents.
Thanks to dchinner for looking at this with me and spotting the
root cause.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function xen_guest_init is using __alloc_percpu with an alignment
which are not power of two.
However, the percpu allocator never supported alignments which are not power
of two and has always behaved incorectly in thise case.
Commit 3ca45a4 "percpu: ensure requested alignment is power of two"
introduced a check which trigger a warning [1] when booting linux-next
on Xen. But in reality this bug was always present.
This can be fixed by replacing the call to __alloc_percpu with
alloc_percpu. The latter will use an alignment which are a power of two.
Commit 9c17d96500f7 ("xen/gntdev: Grant maps should not be subject to
NUMA balancing") set VM_IO flag to prevent grant maps from being
subjected to NUMA balancing.
It was discovered recently that this flag causes get_user_pages() to
always fail with -EFAULT.
We've got a delay loop waiting for secondary CPUs. That loop uses
loops_per_jiffy. However, loops_per_jiffy doesn't actually mean how
many tight loops make up a jiffy on all architectures. It is quite
common to see things like this in the boot log:
Calibrating delay loop (skipped), value calculated using timer
frequency.. 48.00 BogoMIPS (lpj=24000)
In my case I was seeing lots of cases where other CPUs timed out
entering the debugger only to print their stack crawls shortly after the
kdb> prompt was written.
Elsewhere in kgdb we already use udelay(), so that should be safe enough
to use to implement our timeout. We'll delay 1 ms for 1000 times, which
should give us a full second of delay (just like the old code wanted)
but allow us to notice that we're done every 1 ms.
[akpm@linux-foundation.org: simplifications, per Daniel] Link: http://lkml.kernel.org/r/1477091361-2039-1-git-send-email-dianders@chromium.org Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Brian Norris <briannorris@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a off-by-one in the "watchdog: qcom: add option for
standalone watchdog not in timer block" patch that causes the
following panic on boot:
Systemd on reboot enables shutdown watchdog that leaves the watchdog
device open to ensure that even if power down process get stuck the
platform reboots nonetheless.
The iamt_wdt is an alarm-only watchdog and can't reboot system, but the
FW will generate an alarm event reboot was completed in time, as the
watchdog is not automatically disabled during power cycle.
So we should request stop watchdog on reboot to eliminate wrong alarm
from the FW.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NMI handler doesn't call set_irq_regs(), it's set only by normal IRQ.
Thus get_irq_regs() returns NULL or stale registers snapshot with IP/SP
pointing to the code interrupted by IRQ which was interrupted by NMI.
NULL isn't a problem: in this case watchdog calls dump_stack() and
prints full stack trace including NMI. But if we're stuck in IRQ
handler then NMI watchlog will print stack trace without IRQ part at
all.
This patch uses registers snapshot passed into NMI handler as arguments:
these registers point exactly to the instruction interrupted by NMI.
Fixes: 55537871ef66 ("kernel/watchdog.c: perform all-CPU backtrace in case of hard lockup") Link: http://lkml.kernel.org/r/146771764784.86724.6006627197118544150.stgit@buzz Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Ulrich Obergfell <uobergfe@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the current code it is possible to lock a mutex twice when
a subsequent reconnects are triggered. On the 1st reconnect we
reconnect sessions and tcons and then persistent file handles.
If the 2nd reconnect happens during the reconnecting of persistent
file handles then the following sequence of calls is observed:
So, we are trying to acquire the same cfile->fh_mutex twice which
is wrong. Fix this by moving reconnecting of persistent handles to
the delayed work (smb2_reconnect_server) and submitting this work
every time we reconnect tcon in SMB2 commands handling codepath.
This can also lead to corruption of a temporary file list in
cifs_reopen_persistent_file_handles() because we can recursively
call this function twice.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can not unlock/lock cifs_tcp_ses_lock while walking through ses
and tcon lists because it can corrupt list iterator pointers and
a tcon structure can be released if we don't hold an extra reference.
Fix it by moving a reconnect process to a separate delayed work
and acquiring a reference to every tcon that needs to be reconnected.
Also do not send an echo request on newly established connections.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
smbencrypt() points a scatterlist to the stack, which is breaks if
CONFIG_VMAP_STACK=y.
Fix it by switching to crypto_cipher_encrypt_one(). The new code
should be considerably faster as an added benefit.
This code is nearly identical to some code that Eric Biggers
suggested.
Reported-by: Eric Biggers <ebiggers3@gmail.com> Signed-off-by: Andy Lutomirski <luto@kernel.org> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dm_sm_metadata_create() we temporarily change the dm_space_map
operations from 'ops' (whose .destroy function deallocates the
sm_metadata) to 'bootstrap_ops' (whose .destroy function doesn't).
If dm_sm_metadata_create() fails in sm_ll_new_metadata() or
sm_ll_extend(), it exits back to dm_tm_create_internal(), which calls
dm_sm_destroy() with the intention of freeing the sm_metadata, but it
doesn't (because the dm_space_map operations is still set to
'bootstrap_ops').
Fix this by setting the dm_space_map operations back to 'ops' if
dm_sm_metadata_create() fails when it is set to 'bootstrap_ops'.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Acked-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ecbfb9f118 ("dm raid: add raid level takeover support") moved the
configure_discard_support() call from raid_ctr() to raid_preresume().
Enabling/disabling discard _must_ happen during table load (through the
.ctr hook). Fix this regression by moving the
configure_discard_support() call back to raid_ctr().
It is required to hold the queue lock when calling blk_run_queue_async()
to avoid that a race between blk_run_queue_async() and
blk_cleanup_queue() is triggered.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In crypt_set_key(), if a failure occurs while replacing the old key
(e.g. tfm->setkey() fails) the key must not have DM_CRYPT_KEY_VALID flag
set. Otherwise, the crypto layer would have an invalid key that still
has DM_CRYPT_KEY_VALID flag set.
Signed-off-by: Ondrej Kozina <okozina@redhat.com> Reviewed-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return error code -EINVAL instead of 0, as is done elsewhere in
this function.
Fixes: e80d1c805a3b ("dm: do not override error code returned from dm_get_device()") Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dm_table_set_type() is used by a target to establish a DM table's
type (e.g. DM_TYPE_MQ_REQUEST_BASED in the case of DM multipath) the
DM core must go on to verify that the devices in the table are
compatible with the established type.
An earlier DM multipath table could have been build ontop of underlying
devices that were all using blk-mq. In that case, if that active
multipath table is replaced with an empty DM multipath table (that
reflects all paths have failed) then it is important that the
'all_blk_mq' state of the active table is transfered to the new empty DM
table. Otherwise dm-rq.c:dm_old_prep_tio() will incorrectly clone a
request that isn't needed by the DM multipath target when it is to issue
IO to an underlying blk-mq device.
Fixes: e83068a5 ("dm mpath: add optional "queue_mode" feature") Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Tested-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The meaning of the BLK_MQ_S_STOPPED flag is "do not call
.queue_rq()". Hence modify blk_mq_make_request() such that requests
are queued instead of issued if a queue has been stopped.
Reported-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joonyoung Shim reported an interesting problem on his ARM octa-core
Odoroid-XU3 platform. During system suspend, dev_pm_opp_put_regulator()
was failing for a struct device for which dev_pm_opp_set_regulator() is
called earlier.
This happened because an earlier call to
dev_pm_opp_of_cpumask_remove_table() function (from cpufreq-dt.c file)
removed all the entries from opp_table->dev_list apart from the last CPU
device in the cpumask of CPUs sharing the OPP.
But both dev_pm_opp_set_regulator() and dev_pm_opp_put_regulator()
routines get CPU device for the first CPU in the cpumask. And so the OPP
core failed to find the OPP table for the struct device.
This patch attempts to fix this problem by returning a pointer to the
opp_table from dev_pm_opp_set_regulator() and using that as the
parameter to dev_pm_opp_put_regulator(). This ensures that the
dev_pm_opp_put_regulator() doesn't fail to find the opp table.
Note that similar design problem also exists with other
dev_pm_opp_put_*() APIs, but those aren't used currently by anyone and
so we don't need to update them for now.
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ Viresh: Wrote commit log and tested on exynos 5250 ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Cc: <stable@vger.kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vlastimil Babka pointed out that commit 479f854a207c ("mm, page_alloc:
defer debugging checks of pages allocated from the PCP") will allow the
per-cpu list counter to be out of sync with the per-cpu list contents if
a struct page is corrupted.
The consequence is an infinite loop if the per-cpu lists get fully
drained by free_pcppages_bulk because all the lists are empty but the
count is positive. The infinite loop occurs here
do {
batch_free++;
if (++migratetype == MIGRATE_PCPTYPES)
migratetype = 0;
list = &pcp->lists[migratetype];
} while (list_empty(list));
What the user sees is a bad page warning followed by a soft lockup with
interrupts disabled in free_pcppages_bulk().
This patch keeps the accounting in sync.
Fixes: 479f854a207c ("mm, page_alloc: defer debugging checks of pages allocated from the PCP") Link: http://lkml.kernel.org/r/20161202112951.23346-2-mgorman@techsingularity.net Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Christoph Lameter <cl@linux.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our system uses significantly more slab memory with memcg enabled with
the latest kernel. With 3.10 kernel, slab uses 2G memory, while with
4.6 kernel, 6G memory is used. The shrinker has problem. Let's see we
have two memcg for one shrinker. In do_shrink_slab:
1. Check cg1. nr_deferred = 0, assume total_scan = 700. batch size
is 1024, then no memory is freed. nr_deferred = 700
2. Check cg2. nr_deferred = 700. Assume freeable = 20, then
total_scan = 10 or 40. Let's assume it's 10. No memory is freed.
nr_deferred = 10.
The deferred share of cg1 is lost in this case. kswapd will free no
memory even run above steps again and again.
The fix makes sure one memcg's deferred share isn't lost.
Link: http://lkml.kernel.org/r/2414be961b5d25892060315fbb56bb19d81d0c07.1476227351.git.shli@fb.com Signed-off-by: Shaohua Li <shli@fb.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vladimir Davydov <vdavydov@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When removing a namespace we delete it from the subsystem namespaces
list with list_del_init which allows us to know if it is enabled or
not.
The problem is that list_del_init initialize the list next and does
not respect the RCU list-traversal we do on the IO path for locating
a namespace. Instead we need to use list_del_rcu which is allowed to
run concurrently with the _rcu list-traversal primitives (keeps list
next intact) and guarantees concurrent nvmet_find_naespace forward
progress.
By changing that, we cannot rely on ns->dev_link for knowing if the
namspace is enabled, so add enabled indicator entry to nvmet_ns for
that.
In the last ilen case, i was already increased, resulting in accessing out-
of-boundary entry of do_replace and blkaddr.
Fix to check ilen first to exit the loop.
Fixes: 2aa8fbb9693020 ("f2fs: refactor __exchange_data_block for speed up") Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct file_operations instance serving the f2fs/status debugfs file
lacks an initialization of its ->owner.
This means that although that file might have been opened, the f2fs module
can still get removed. Any further operation on that opened file, releasing
included, will cause accesses to unmapped memory.
Indeed, Mike Marshall reported the following:
BUG: unable to handle kernel paging request at ffffffffa0307430
IP: [<ffffffff8132a224>] full_proxy_release+0x24/0x90
<...>
Call Trace:
[] __fput+0xdf/0x1d0
[] ____fput+0xe/0x10
[] task_work_run+0x8e/0xc0
[] do_exit+0x2ae/0xae0
[] ? __audit_syscall_entry+0xae/0x100
[] ? syscall_trace_enter+0x1ca/0x310
[] do_group_exit+0x44/0xc0
[] SyS_exit_group+0x14/0x20
[] do_syscall_64+0x61/0x150
[] entry_SYSCALL64_slow_path+0x25/0x25
<...>
---[ end trace f22ae883fa3ea6b8 ]---
Fixing recursive fault but reboot is needed!
Fix this by initializing the f2fs/status file_operations' ->owner with
THIS_MODULE.
This will allow debugfs to grab a reference to the f2fs module upon any
open on that file, thus preventing it from getting removed.
Fixes: 902829aa0b72 ("f2fs: move proc files to debugfs") Reported-by: Mike Marshall <hubcap@omnibond.com> Reported-by: Martin Brandenburg <martin@omnibond.com> Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently data journalling is incompatible with encryption: enabling both
at the same time has never been supported by design, and would result in
unpredictable behavior. However, users are not precluded from turning on
both features simultaneously. This change programmatically replaces data
journaling for encrypted regular files with ordered data journaling mode.
Background:
Journaling encrypted data has not been supported because it operates on
buffer heads of the page in the page cache. Namely, when the commit
happens, which could be up to five seconds after caching, the commit
thread uses the buffer heads attached to the page to copy the contents of
the page to the journal. With encryption, it would have been required to
keep the bounce buffer with ciphertext for up to the aforementioned five
seconds, since the page cache can only hold plaintext and could not be
used for journaling. Alternatively, it would be required to setup the
journal to initiate a callback at the commit time to perform deferred
encryption - in this case, not only would the data have to be written
twice, but it would also have to be encrypted twice. This level of
complexity was not justified for a mode that in practice is very rarely
used because of the overhead from the data journalling.
Solution:
If data=journaled has been set as a mount option for a filesystem, or if
journaling is enabled on a regular file, do not perform journaling if the
file is also encrypted, instead fall back to the data=ordered mode for the
file.
Rationale:
The intent is to allow seamless and proper filesystem operation when
journaling and encryption have both been enabled, and have these two
conflicting features gracefully resolved by the filesystem.
Fixes: 67cf5b09a46f ("ext4: add the basic function for inline data support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit "ext4: sanity check the block and cluster size at mount
time" should prevent any problems, but in case the superblock is
modified while the file system is mounted, add an extra safety check
to make sure we won't overrun the allocated buffer.
Fix a large number of problems with how we handle mount options in the
superblock. For one, if the string in the superblock is long enough
that it is not null terminated, we could run off the end of the string
and try to interpret superblocks fields as characters. It's unlikely
this will cause a security problem, but it could result in an invalid
parse. Also, parse_options is destructive to the string, so in some
cases if there is a comma-separated string, it would be modified in
the superblock. (Fortunately it only happens on file systems with a
1k block size.)
The number of 'counters' elements needed in 'struct sg' is
super_block->s_blocksize_bits + 2. Presently we have 16 'counters'
elements in the array. This is insufficient for block sizes >= 32k. In
such cases the memcpy operation performed in ext4_mb_seq_groups_show()
would cause stack memory corruption.
Fixes: c9de560ded61f Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'border' variable is set to a value of 2 times the block size of the
underlying filesystem. With 64k block size, the resulting value won't
fit into a 16-bit variable. Hence this commit changes the data type of
'border' to 'unsigned int'.
If there is an error reported in mballoc via ext4_grp_locked_error(),
the code is holding a spinlock, so ext4_commit_super() must not try to
lock the buffer head, or else it will trigger a BUG:
Since ext4_grp_locked_error() calls ext4_commit_super with sync == 0
(and it is the only caller which does so), avoid locking and unlocking
the buffer in this case.
This can result in races with ext4_commit_super() if there are other
problems (which is what commit 4743f83990614 was trying to address),
but a Warning is better than BUG.
Fixes: 4743f83990614 Reported-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AEAD givenc descriptor relies on moving the IV through the
output FIFO and then back to the CTX2 for authentication. The
SEQ FIFO STORE could be scheduled before the data can be
read from OFIFO, especially since the SEQ FIFO LOAD needs
to wait for the SEQ FIFO LOAD SKIP to finish first. The
SKIP takes more time when the input is SG than when it's
a contiguous buffer. If the SEQ FIFO LOAD is not scheduled
before the STORE, the DECO will hang waiting for data
to be available in the OFIFO so it can be transferred to C2.
In order to overcome this, first force transfer of IV to C2
by starting the "cryptlen" transfer first and then starting to
store data from OFIFO to the output buffer.
It is the reasonable expectation that if an executable file is not
readable there will be no way for a user without special privileges to
read the file. This is enforced in ptrace_attach but if ptrace
is already attached before exec there is no enforcement for read-only
executables.
As the only way to read such an mm is through access_process_vm
spin a variant called ptrace_access_vm that will fail if the
target process is not being ptraced by the current process, or
the current process did not have sufficient privileges when ptracing
began to read the target processes mm.
In the ptrace implementations replace access_process_vm by
ptrace_access_vm. There remain several ptrace sites that still use
access_process_vm as they are reading the target executables
instructions (for kernel consumption) or register stacks. As such it
does not appear necessary to add a permission check to those calls.
This bug has always existed in Linux.
Fixes: v1.0 Reported-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the flag PT_PTRACE_CAP was added the PTRACE_TRACEME path was
overlooked. This can result in incorrect behavior when an application
like strace traces an exec of a setuid executable.
Further PT_PTRACE_CAP does not have enough information for making good
security decisions as it does not report which user namespace the
capability is in. This has already allowed one mistake through
insufficient granulariy.
I found this issue when I was testing another corner case of exec and
discovered that I could not get strace to set PT_PTRACE_CAP even when
running strace as root with a full set of caps.
This change fixes the above issue with strace allowing stracing as
root a setuid executable without disabling setuid. More fundamentaly
this change allows what is allowable at all times, by using the correct
information in it's decision.
We truncated the possible read iterator to s_maxbytes in commit c2a9737f45e2 ("vfs,mm: fix a dead loop in truncate_inode_pages_range()"),
but our end condition handling was wrong: it's not an error to try to
read at the end of the file.
Reading past the end should return EOF (0), not EINVAL.
During exec dumpable is cleared if the file that is being executed is
not readable by the user executing the file. A bug in
ptrace_may_access allows reading the file if the executable happens to
enter into a subordinate user namespace (aka clone(CLONE_NEWUSER),
unshare(CLONE_NEWUSER), or setns(fd, CLONE_NEWUSER).
This problem is fixed with only necessary userspace breakage by adding
a user namespace owner to mm_struct, captured at the time of exec, so
it is clear in which user namespace CAP_SYS_PTRACE must be present in
to be able to safely give read permission to the executable.
The function ptrace_may_access is modified to verify that the ptracer
has CAP_SYS_ADMIN in task->mm->user_ns instead of task->cred->user_ns.
This ensures that if the task changes it's cred into a subordinate
user namespace it does not become ptraceable.
The function ptrace_attach is modified to only set PT_PTRACE_CAP when
CAP_SYS_PTRACE is held over task->mm->user_ns. The intent of
PT_PTRACE_CAP is to be a flag to note that whatever permission changes
the task might go through the tracer has sufficient permissions for
it not to be an issue. task->cred->user_ns is always the same
as or descendent of mm->user_ns. Which guarantees that having
CAP_SYS_PTRACE over mm->user_ns is the worst case for the tasks
credentials.
To prevent regressions mm->dumpable and mm->user_ns are not considered
when a task has no mm. As simply failing ptrace_may_attach causes
regressions in privileged applications attempting to read things
such as /proc/<pid>/stat
Acked-by: Kees Cook <keescook@chromium.org> Tested-by: Cyrill Gorcunov <gorcunov@openvz.org> Fixes: 8409cca70561 ("userns: allow ptrace from non-init user namespaces") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bdev->bd_contains is not stable before calling __blkdev_get().
When __blkdev_get() is called on a parition with ->bd_openers == 0
it sets
bdev->bd_contains = bdev;
which is not correct for a partition.
After a call to __blkdev_get() succeeds, ->bd_openers will be > 0
and then ->bd_contains is stable.
When FMODE_EXCL is used, blkdev_get() calls
bd_start_claiming() -> bd_prepare_to_claim() -> bd_may_claim()
This call happens before __blkdev_get() is called, so ->bd_contains
is not stable. So bd_may_claim() cannot safely use ->bd_contains.
It currently tries to use it, and this can lead to a BUG_ON().
This happens when a whole device is already open with a bd_holder (in
use by dm in my particular example) and two threads race to open a
partition of that device for the first time, one opening with O_EXCL and
one without.
The thread that doesn't use O_EXCL gets through blkdev_get() to
__blkdev_get(), gains the ->bd_mutex, and sets bdev->bd_contains = bdev;
Immediately thereafter the other thread, using FMODE_EXCL, calls
bd_start_claiming() from blkdev_get(). This should fail because the
whole device has a holder, but because bdev->bd_contains == bdev
bd_may_claim() incorrectly reports success.
This thread continues and blocks on bd_mutex.
The first thread then sets bdev->bd_contains correctly and drops the mutex.
The thread using FMODE_EXCL then continues and when it calls bd_may_claim()
again in:
BUG_ON(!bd_may_claim(bdev, whole, holder));
The BUG_ON fires.
Fix this by removing the dependency on ->bd_contains in
bd_may_claim(). As bd_may_claim() has direct access to the whole
device, it can simply test if the target bdev is the whole device.
Commit 8924feff66f3 ("splice: lift pipe_lock out of splice_to_pipe()")
caused a regression when there were no more readers left on a pipe that
was being spliced into: rather than the expected SIGPIPE and -EPIPE
return value, the writer would end up waiting forever for space to free
up (which obviously was not going to happen with no readers around).
Fixes: 8924feff66f3 ("splice: lift pipe_lock out of splice_to_pipe()") Reported-and-tested-by: Andreas Schwab <schwab@linux-m68k.org> Debugged-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you have a process that has set itself to be non-dumpable, and it
then undergoes exec(2), any CLOEXEC file descriptors it has open are
"exposed" during a race window between the dumpable flags of the process
being reset for exec(2) and CLOEXEC being applied to the file
descriptors. This can be exploited by a process by attempting to access
/proc/<pid>/fd/... during this window, without requiring CAP_SYS_PTRACE.
The race in question is after set_dumpable has been (for get_link,
though the trace is basically the same for readlink):
Which will return 0, during the race window and CLOEXEC file descriptors
will still be open during this window because do_close_on_exec has not
been called yet. As a result, the ordering of these calls should be
reversed to avoid this race window.
This is of particular concern to container runtimes, where joining a
PID namespace with file descriptors referring to the host filesystem
can result in security issues (since PRCTL_SET_DUMPABLE doesn't protect
against access of CLOEXEC file descriptors -- file descriptors which may
reference filesystem objects the container shouldn't have access to).
Cc: dev@opencontainers.org Reported-by: Michael Crosby <crosbymichael@gmail.com> Signed-off-by: Aleksa Sarai <asarai@suse.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user namespace support was merged the need to prevent
ptrace from revealing the contents of an unreadable executable
was overlooked.
Correct this oversight by ensuring that the executed file
or files are in mm->user_ns, by adjusting mm->user_ns.
Use the new function privileged_wrt_inode_uidgid to see if
the executable is a member of the user namespace, and as such
if having CAP_SYS_PTRACE in the user namespace should allow
tracing the executable. If not update mm->user_ns to
the parent user namespace until an appropriate parent is found.
Reported-by: Jann Horn <jann@thejh.net> Fixes: 9e4a36ece652 ("userns: Fail exec for suid and sgid binaries with ids outside our user namespace.") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term
frequency drift. The frequency drift magnitude depends on the VCO update
rate, which is inversely proportional to the PLL divider. The kernel
DPLL configuration code results in a high value for the divider, leading
to a long term drift high enough to cause USB transmission errors. In
the worst case the USB PHY's ULPI interface can stop responding,
breaking USB operation completely. This manifests itself on the
Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the
cable is bad?' in the kernel log.
Errata sprz319 advisory 2.1 documents PLL values that minimize the
drift. Use them automatically when DPLL5 is used for USB operation,
which we detect based on the requested clock rate. The clock framework
will still compute the PLL parameters and resulting rate as usual, but
the PLL M and N values will then be overridden. This can result in the
effective clock rate being slightly different than the rate cached by
the clock framework, but won't cause any adverse effect to USB
operation.
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
[Upported from v3.2 to v4.9] Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit [64047d7f4912 ALSA: hda - ignore the assoc and seq when comparing
pin configurations] intented to ignore both seq and assoc at pin
comparing, but it only ignored seq. So that commit may still fail to
match pins on some machines.
Change the bitmask to also ignore assoc.
v2: Use macro to do bit masking.
Thanks to Hui Wang for the analysis.
Fixes: 64047d7f4912 ("ALSA: hda - ignore the assoc and seq when comparing...") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HP Z1 Gen3 AiO with Conexant codec doesn't give an unsolicited event
to the headset mic pin upon the jack plugging, it reports only to the
headphone pin. It results in the missing mic switching. Let's fix up
by simply gating the jack event.
More and more pin configurations have been adding to the pin quirk
table, lots of them are only different from assoc and seq, but they
all apply to the same QUIRK_FIXUP, if we don't compare assoc and seq
when matching pin configurations, it will greatly reduce the pin
quirk table size.
We have tested this change on a couple of Dell laptops, it worked
well.
Sampling rate changes after first set one are not reflected to the
hardware, while driver and ALSA think the rate has been changed.
Fix the problem by properly stopping the interface at the beginning of
prepare call, allowing new rate to be set to the hardware. This keeps
the hardware in sync with the driver.
The Logitech QuickCam Communicate Deluxe/S7500 microphone fails with the
following warning.
[ 6.778995] usb 2-1.2.2.2: Warning! Unlikely big volume range (=3072),
cval->res is probably wrong.
[ 6.778996] usb 2-1.2.2.2: [5] FU [Mic Capture Volume] ch = 1, val =
4608/7680/1
Adding it to the list of devices in volume_control_quirks makes it work
properly, fixing related typo.
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
usb_endpoint_maxp() returns wMaxPacketSize in its
raw form. Without taking into consideration that it
also contains other bits reserved for isochronous
endpoints.
This patch fixes one occasion where this is a
problem by making sure that we initialize
ep->maxpacket only with lower 10 bits of the value
returned by usb_endpoint_maxp(). Note that seperate
patches will be necessary to audit all call sites of
usb_endpoint_maxp() and make sure that
usb_endpoint_maxp() only returns lower 10 bits of
wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling brightness_set manually isn't safe as some LED drivers don't
implement this callback. The best idea is to just use a proper helper
which will fallback to the brightness_set_blocking callback if needed.
Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Fixes: 0f247626cbb ("usb: core: Introduce a USB port LED trigger") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB-3 does not have any link state that will avoid negotiating a connection
with a plugged-in cable but will signal the host when the cable is
unplugged.
For USB-3 we used to first set the link to Disabled, then to RxDdetect to
be able to detect cable connects or disconnects. But in RxDetect the
connected device is detected again and eventually enabled.
Instead set the link into U3 and disable remote wakeups for the device.
This is what Windows does, and what Alan Stern suggested.
Cc: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of High-Speed, High-Bandwidth endpoints, we
need to tell DWC3 that we have more than one packet
per interval. We do that by setting PCM1 field of
Isochronous-First TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were setting the qgroup_rescan_running flag to true only after the
rescan worker started (which is a task run by a queue). So if a user
space task starts a rescan and immediately after asks to wait for the
rescan worker to finish, this second call might happen before the rescan
worker task starts running, in which case the rescan wait ioctl returns
immediatley, not waiting for the rescan worker to finish.
This was making the fstest btrfs/022 fail very often.
Fixes: d2c609b834d6 (btrfs: properly track when rescan worker is running) Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can not simply use the owner field from an extent buffer's header to
get the id of the respective tree when the extent buffer is from a
relocation tree. When we create the root for a relocation tree we leave
(on purpose) the owner field with the same value as the subvolume's tree
root (we do this at ctree.c:btrfs_copy_root()). So we must ignore extent
buffers from relocation trees, which have the BTRFS_HEADER_FLAG_RELOC
flag set, because otherwise we will always consider the extent buffer
as not being the root of the tree (the root of original subvolume tree
is always different from the root of the respective relocation tree).
This lead to assertion failures when running with the integrity checker
enabled (CONFIG_BTRFS_FS_CHECK_INTEGRITY=y) such as the following:
This can be easily reproduced by running xfstests with the integrity
checker enabled.
Fixes: 1ba98d086fe3 (Btrfs: detect corruption when non-root leaf has zero item) Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The balance status item contains currently known filter values, but the
stripes filter was unintentionally not among them. This would mean, that
interrupted and automatically restarted balance does not apply the
stripe filters.
Fixes: dee32d0ac3719ef8d640efaf0884111df444730f Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During relocation of a data block group we create a relocation tree
for each fs/subvol tree by making a snapshot of each tree using
btrfs_copy_root() and the tree's commit root, and then setting the last
snapshot field for the fs/subvol tree's root to the value of the current
transaction id minus 1. However this can lead to relocation later
dropping references that it did not create if we have qgroups enabled,
leaving the filesystem in an inconsistent state that keeps aborting
transactions.
Lets consider the following example to explain the problem, which requires
qgroups to be enabled.
We are relocating data block group Y, we have a subvolume with id 258 that
has a root at level 1, that subvolume is used to store directory entries
for snapshots and we are currently at transaction 3404.
When committing transaction 3404, we have a pending snapshot and therefore
we call btrfs_run_delayed_items() at transaction.c:create_pending_snapshot()
in order to create its dentry at subvolume 258. This results in COWing
leaf A from root 258 in order to add the dentry. Note that leaf A
also contains file extent items referring to extents from some other
block group X (we are currently relocating block group Y). Later on, still
at create_pending_snapshot() we call qgroup_account_snapshot(), which
switches the commit root for root 258 when it calls switch_commit_roots(),
so now the COWed version of leaf A, lets call it leaf A', is accessible
from the commit root of tree 258. At the end of qgroup_account_snapshot(),
we call record_root_in_trans() with 258 as its argument, which results
in btrfs_init_reloc_root() being called, which in turn calls
relocation.c:create_reloc_root() in order to create a relocation tree
associated to root 258, which results in assigning the value of 3403
(which is the current transaction id minus 1 = 3404 - 1) to the
last_snapshot field of root 258. When creating the relocation tree root
at ctree.c:btrfs_copy_root() we add a shared reference for leaf A',
corresponding to the relocation tree's root, when we call btrfs_inc_ref()
against the COWed root (a copy of the commit root from tree 258), which
is at level 1. So at this point leaf A' has 2 references, one normal
reference corresponding to root 258 and one shared reference corresponding
to the root of the relocation tree.
Transaction 3404 finishes its commit and transaction 3405 is started by
relocation when calling merge_reloc_root() for the relocation tree
associated to root 258. In the meanwhile leaf A' is COWed again, in
response to some filesystem operation, when we are still at transaction
3405. However when we COW leaf A', at ctree.c:update_ref_for_cow(), we
call btrfs_block_can_be_shared() in order to figure out if other trees
refer to the leaf and if any such trees exists, add a full back reference
to leaf A' - but btrfs_block_can_be_shared() incorrectly returns false
because the following condition is false:
which evaluates to 3404 <= 3403. So after leaf A' is COWed, it stays with
only one reference, corresponding to the shared reference we created when
we called btrfs_copy_root() to create the relocation tree's root and
btrfs_inc_ref() ends up not being called for leaf A' nor we end up setting
the flag BTRFS_BLOCK_FLAG_FULL_BACKREF in leaf A'. This results in not
adding shared references for the extents from block group X that leaf A'
refers to with its file extent items.
Later, after merging the relocation root we do a call to to
btrfs_drop_snapshot() in order to delete the relocation tree. This ends
up calling do_walk_down() when path->slots[1] points to leaf A', which
results in calling btrfs_lookup_extent_info() to get the number of
references for leaf A', which is 1 at this time (only the shared reference
exists) and this value is stored at wc->refs[0]. After this walk_up_proc()
is called when wc->level is 0 and path->nodes[0] corresponds to leaf A'.
Because the current level is 0 and wc->refs[0] is 1, it does call
btrfs_dec_ref() against leaf A', which results in removing the single
references that the extents from block group X have which are associated
to root 258 - the expectation was to have each of these extents with 2
references - one reference for root 258 and one shared reference related
to the root of the relocation tree, and so we would drop only the shared
reference (because leaf A' was supposed to have the flag
BTRFS_BLOCK_FLAG_FULL_BACKREF set).
This leaves the filesystem in an inconsistent state as we now have file
extent items in a subvolume tree that point to extents from block group X
without references in the extent tree. So later on when we try to decrement
the references for these extents, for example due to a file unlink operation,
truncate operation or overwriting ranges of a file, we fail because the
expected references do not exist in the extent tree.
This leads to warnings and transaction aborts like the following:
This was happening often on openSUSE and SLE systems using btrfs as the
root filesystem (with its default layout where multiple subvolumes are
used) where balance happens in the background triggered by a cron job and
snapshots are automatically created before/after package installations,
upgrades and removals. The issue could be triggered simply by running the
following loop on the first system boot post installation:
while true; do
zypper -n in nfs-kernel-server
zypper -n rm nfs-kernel-server
done
(If we were fast enough and made that loop before the cron job triggered
a balance operation and the balance finished)
So fix by setting the last_snapshot field of the root to the value of the
generation of its commit root. Like this btrfs_block_can_be_shared()
behaves correctly for the case where the relocation root is created during
a transaction commit and for the case where it's created before a
transaction commit.
Fixes: 6426c7ad697d (btrfs: qgroup: Fix qgroup accounting when creating snapshot) Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
leaf N:
...
item 240 key (282 DIR_LOG_ITEM 0) itemoff 8189 itemsize 8
dir log end 1275809046
leaf N + 1:
item 0 key (282 DIR_LOG_ITEM 3936149215) itemoff 16275 itemsize 8
dir log end 18446744073709551615
...
When we pass the value 1275809046 + 1 as the parameter start_ret to the
function tree-log.c:find_dir_range() (done by replay_dir_deletes()), we
end up with path->slots[0] having the value 239 (points to the last item
of leaf N, item 240). Because the dir log item in that position has an
offset value smaller than *start_ret (1275809046 + 1) we need to move on
to the next leaf, however the logic for that is wrong since it compares
the current slot to the number of items in the leaf, which is smaller
and therefore we don't lookup for the next leaf but instead we set the
slot to point to an item that does not exist, at slot 240, and we later
operate on that slot which has unexpected content or in the worst case
can result in an invalid memory access (accessing beyond the last page
of leaf N's extent buffer).
So fix the logic that checks when we need to lookup at the next leaf
by first incrementing the slot and only after to check if that slot
is beyond the last item of the current leaf.
Signed-off-by: Robbie Ko <robbieko@synology.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Fixes: e02119d5a7b4 (Btrfs: Add a write ahead tree log to optimize synchronous operations) Signed-off-by: Filipe Manana <fdmanana@suse.com>
[Modified changelog for clarity and correctness] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While logging new directory entries, at tree-log.c:log_new_dir_dentries(),
after we call btrfs_search_forward() we get a leaf with a read lock on it,
and without unlocking that leaf we can end up calling btrfs_iget() to get
an inode pointer. The later (btrfs_iget()) can end up doing a read-only
search on the same tree again, if the inode is not in memory already, which
ends up causing a deadlock if some other task in the meanwhile started a
write search on the tree and is attempting to write lock the same leaf
that btrfs_search_forward() locked while holding write locks on upper
levels of the tree blocking the read search from btrfs_iget(). In this
scenario we get a deadlock.
So fix this by releasing the search path before calling btrfs_iget() at
tree-log.c:log_new_dir_dentries().
This can only happen with CONFIG_BTRFS_FS_CHECK_INTEGRITY=y.
Commit 1ba98d0 ("Btrfs: detect corruption when non-root leaf has zero item")
assumes that a leaf is its root when leaf->bytenr == btrfs_root_bytenr(root),
however, we should not use btrfs_root_bytenr(root) since it's mainly got
updated during committing transaction. So the check can fail when doing
COW on this leaf while it is a root.
This changes to use "if (leaf == btrfs_root_node(root))" instead, just like
how we check whether leaf is a root in __btrfs_cow_block().
Fixes: 1ba98d086fe3 (Btrfs: detect corruption when non-root leaf has zero item) Reported-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem statement: unprivileged user who has read-write access to more than
one btrfs subvolume may easily consume all kernel memory (eventually
triggering oom-killer).
Reproducer (./mkrmdir below essentially loops over mkdir/rmdir):
[root@kteam1 ~]# cat prep.sh
DEV=/dev/sdb
mkfs.btrfs -f $DEV
mount $DEV /mnt
for i in `seq 1 16`
do
mkdir /mnt/$i
btrfs subvolume create /mnt/SV_$i
ID=`btrfs subvolume list /mnt |grep "SV_$i$" |cut -d ' ' -f 2`
mount -t btrfs -o subvolid=$ID $DEV /mnt/$i
chmod a+rwx /mnt/$i
done
[root@kteam1 ~]# sh prep.sh
[maxim@kteam1 ~]$ for i in `seq 1 16`; do ./mkrmdir /mnt/$i 2000 2000 & done
The huge numbers above come from insane number of async_work-s allocated
and queued by btrfs_wq_run_delayed_node.
The problem is caused by btrfs_wq_run_delayed_node() queuing more and more
works if the number of delayed items is above BTRFS_DELAYED_BACKGROUND. The
worker func (btrfs_async_run_delayed_root) processes at least
BTRFS_DELAYED_BATCH items (if they are present in the list). So, the machinery
works as expected while the list is almost empty. As soon as it is getting
bigger, worker func starts to process more than one item at a time, it takes
longer, and the chances to have async_works queued more than needed is getting
higher.
The problem above is worsened by another flaw of delayed-inode implementation:
if async_work was queued in a throttling branch (number of items >=
BTRFS_DELAYED_WRITEBACK), corresponding worker func won't quit until
the number of items < BTRFS_DELAYED_BACKGROUND / 2. So, it is possible that
the func occupies CPU infinitely (up to 30sec in my experiments): while the
func is trying to drain the list, the user activity may add more and more
items to the list.
The patch fixes both problems in straightforward way: refuse queuing too
many works in btrfs_wq_run_delayed_node and bail out of worker func if
at least BTRFS_DELAYED_WRITEBACK items are processed.
Changed in v2: remove support of thresh == NO_THRESHOLD.
Yu Zhao has noticed that __unregister_cpu_notifier only unregisters its
notifiers when HOTPLUG_CPU=y while the registration might succeed even
when HOTPLUG_CPU=n if MODULE is enabled. This means that e.g. zswap
might keep a stale notifier on the list on the manual clean up during
the pool tear down and thus corrupt the list. Resulting in the following
This can be even triggered manually by changing
/sys/module/zswap/parameters/compressor multiple times.
Fix this issue by making unregister APIs symmetric to the register so
there are no surprises.
Fixes: 47e627bc8c9a ("[PATCH] hotplug: Allow modules to use the cpu hotplug notifiers even if !CONFIG_HOTPLUG_CPU") Reported-and-tested-by: Yu Zhao <yuzhao@google.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Cc: linux-mm@kvack.org Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dan Streetman <ddstreet@ieee.org> Link: http://lkml.kernel.org/r/20161207135438.4310-1-mhocko@kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 11 Dec 2016 18:17:39 +0000 (10:17 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Two more MIPS fixes for 4.9:
- RTC: Return -ENODEV so an external RTC will be tried
- Fix mask of GPE frequency
These two have been tested on Imagination's automated test system and
also both received positive reviews on the linux-mips mailing list"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Lantiq: Fix mask of GPE frequency
MIPS: Return -ENODEV from weak implementation of rtc_mips_set_time
projects / linux-beck.git / log