John Fastabend [Thu, 10 Feb 2011 14:40:01 +0000 (14:40 +0000)]
ixgbe: DCB, implement 802.1Qaz routines
Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Wed, 5 Jan 2011 04:47:43 +0000 (04:47 +0000)]
ixgbe: DCB, abstract out dcb_config from DCB hardware configuration
Currently the routines that configure the HW for DCB require a
ixgbe_dcb_config structure. This structure was designed to support
the CEE standard and does not match the IEEE standard well.
This patch changes the HW routines in ixgbe_dcb_8259x.{ch} to use
raw pfc and bandwidth values. This requires some parsing of the DCB
configuration but makes the HW routines independent of the data
structure that contains the DCB configuration.
The primary advantage to doing this is we can do HW setup directly
from the 802.1Qaz ops without having to arbitrarily encapsulate this
data into the CEE structure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Wed, 5 Jan 2011 04:47:38 +0000 (04:47 +0000)]
ixgbe: DCB, remove round robin mode on 82598 devices
Remove round robin configuration code for 82598 parts it
is not settable and is always false.
If we need/want this in the future we can add it back properly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Tue, 1 Feb 2011 02:10:20 +0000 (02:10 +0000)]
ixgbe: DCB, only reprogram HW if the FCoE priority is changed
If the FCoE priority is not changing do not set the RESET and
APP_UPCHG bits. This causes unneeded HW resets and which can
cause unneeded LLDP frames and negotiations.
The current check is not sufficient because the FCoE priority
can change twice during a negotiation which results in the
bits being set. This occurs when the switch changes the
priority or when the link is reset with switches that do not
include the APP priority until after PFC has been negotiated.
This results in set_app being called with the local APP
priority. Then the negotiation completes and set_app
is called again with the peer APP priority. The check
fails so the device is reset and the above occurs again
resulting in an endless loop of resets.
By only resetting the device if the APP priority has really
changed we short circuit the loop.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Thu, 20 Jan 2011 06:58:07 +0000 (06:58 +0000)]
e1000e: return appropriate errors for 'ethtool -r'
...when invoked while interface is not up or when auto-negotiation is
disabled as done by other drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 19 Jan 2011 04:23:39 +0000 (04:23 +0000)]
e1000e: use correct pointer when memcpy'ing a 2-dimensional array
*e1000_gstrings_test is not the same size as e1000_gstrings_test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 19 Jan 2011 04:20:59 +0000 (04:20 +0000)]
e1000e: replace unbounded sprintf with snprintf
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Tue, 8 Feb 2011 04:38:06 +0000 (20:38 -0800)]
inet: Create a mechanism for upward inetpeer propagation into routes.
If we didn't have a routing cache, we would not be able to properly
propagate certain kinds of dynamic path attributes, for example
PMTU information and redirects.
The reason is that if we didn't have a routing cache, then there would
be no way to lookup all of the active cached routes hanging off of
sockets, tunnels, IPSEC bundles, etc.
Consider the case where we created a cached route, but no inetpeer
entry existed and also we were not asked to pre-COW the route metrics
and therefore did not force the creation a new inetpeer entry.
If we later get a PMTU message, or a redirect, and store this
information in a new inetpeer entry, there is no way to teach that
cached route about the newly existing inetpeer entry.
The facilities implemented here handle this problem.
First we create a generation ID. When we create a cached route of any
kind, we remember the generation ID at the time of attachment. Any
time we force-create an inetpeer entry in response to new path
information, we bump that generation ID.
The dst_ops->check() callback is where the knowledge of this event
is propagated. If the global generation ID does not equal the one
stored in the cached route, and the cached route has not attached
to an inetpeer yet, we look it up and attach if one is found. Now
that we've updated the cached route's information, we update the
route's generation ID too.
This clears the way for implementing PMTU and redirects directly in
the inetpeer cache. There is absolutely no need to consult cached
route information in order to maintain this information.
At this point nothing bumps the inetpeer genids, that comes in the
later changes which handle PMTUs and redirects using inetpeers.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 9 Feb 2011 23:36:47 +0000 (15:36 -0800)]
inetpeer: Add redirect and PMTU discovery cached info.
Validity of the cached PMTU information is indicated by it's
expiration value being non-zero, just as per dst->expires.
The scheme we will use is that we will remember the pre-ICMP value
held in the metrics or route entry, and then at expiration time
we will restore that value.
In this way PMTU expiration does not kill off the cached route as is
done currently.
Redirect information is permanent, or at least until another redirect
is received.
Signed-off-by: David S. Miller <davem@davemloft.net>
Xiaotian Feng [Thu, 10 Feb 2011 03:16:15 +0000 (19:16 -0800)]
net: rename group sysfs entry to netdev_group
commit a512b92 adds sysfs entry for net device group, but
before this commit, tun also uses group sysfs, so after this
commit checkin, kernel warns like this:
sysfs: cannot create duplicate filename '/devices/virtual/net/vnet0/group'
Since tun has used this for years, rename sysfs under tun might
break existing userspace, so rename group sysfs entry for net device
group is a better choice.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomoya [Mon, 7 Feb 2011 23:29:02 +0000 (23:29 +0000)]
pch_can: fix rmmod issue
Currently, when rmmod pch_can, kernel failure occurs.
The cause is pci_iounmap executed before pch_can_reset.
Thus pci_iounmap moves after pch_can_reset.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomoya [Mon, 7 Feb 2011 23:29:01 +0000 (23:29 +0000)]
pch_can: fix 800k comms issue
Currently, 800k comms fails since prop_seg set zero.
(EG20T PCH CAN register of prop_seg must be set more than 1)
To prevent prop_seg set to zero, change tseg2_min 1 to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 8 Feb 2011 23:02:50 +0000 (15:02 -0800)]
net: Fix lockdep regression caused by initializing netdev queues too early.
In commit aa9421041128abb4d269ee1dc502ff65fb3b7d69 ("net: init ingress
queue") we moved the allocation and lock initialization of the queues
into alloc_netdev_mq() since register_netdevice() is way too late.
The problem is that dev->type is not setup until the setup()
callback is invoked by alloc_netdev_mq(), and the dev->type is
what determines the lockdep class to use for the locks in the
queues.
Fix this by doing the queue allocation after the setup() callback
runs.
This is safe because the setup() callback is not allowed to make any
state changes that need to be undone on error (memory allocations,
etc.). It may, however, make state changes that are undone by
free_netdev() (such as netif_napi_add(), which is done by the
ipoib driver's setup routine).
The previous code also leaked a reference to the &init_net namespace
object on RX/TX queue allocation failures.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 8 Feb 2011 22:31:31 +0000 (14:31 -0800)]
net/caif: Fix dangling list pointer in freed object on error.
rtnl_link_ops->setup(), and the "setup" callback passed to alloc_netdev*(),
cannot make state changes which need to be undone on failure. There is
no cleanup mechanism available at this point.
So we have to add the caif private instance to the global list once we
are sure that register_netdev() has succedded in ->newlink().
Otherwise, if register_netdev() fails, the caller will invoke free_netdev()
and we will have a reference to freed up memory on the chnl_net_list.
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Wed, 2 Feb 2011 06:29:02 +0000 (06:29 +0000)]
ipsec: allow to align IPv4 AH on 32 bits
The Linux IPv4 AH stack aligns the AH header on a 64 bit boundary
(like in IPv6). This is not RFC compliant (see RFC4302, Section
3.3.3.2.1), it should be aligned on 32 bits.
For most of the authentication algorithms, the ICV size is 96 bits.
The AH header alignment on 32 or 64 bits gives the same results.
However for SHA-256-128 for instance, the wrong 64 bit alignment results
in adding useless padding in IPv4 AH, which is forbidden by the RFC.
To avoid breaking backward compatibility, we use a new flag
(XFRM_STATE_ALIGN4) do change original behavior.
Initial patch from Dang Hongwu <hongwu.dang@6wind.com> and
Christophe Gouault <christophe.gouault@6wind.com>.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Changes:
- driver updated to match cdc.h header with errata changes
- added support for USB_CDC_SET_NTB_INPUT_SIZE control request with
8 byte length
- fixes to comply with specification: send only control requests supported by
device, set number of datagrams for IN direction, connection speed structure
update, etc.
- packet loss fixed for tx direction; misleading flag renamed.
- adjusted hard_mtu value.
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Orishko [Mon, 7 Feb 2011 09:45:09 +0000 (09:45 +0000)]
CDC NCM errata updates for cdc.h
Changes are based on the following documents:
- CDC NCM errata:
http://www.usb.org/developers/devclass_docs/NCM10_012011.zip
- CDC and WMC errata link:
http://www.usb.org/developers/devclass_docs/CDC1.2_WMC1.1_012011.zip
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Wed, 26 Jan 2011 06:04:17 +0000 (06:04 +0000)]
ixgbe: cleanup variable initialization
The ixgbe_fcoe_ddp_get function wasn't initializing one of its variables
and this was producing compiler warnings. This patch cleans that up.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 19 Jan 2011 18:33:05 +0000 (18:33 +0000)]
ixgbe: limit VF access to network traffic
This change fixes VM pool allocation issues based on MAC address filtering,
as well as limits the scope of VF access to promiscuous mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Tue, 18 Jan 2011 22:53:47 +0000 (22:53 +0000)]
ixgbe: fix for 82599 erratum on Header Splitting
We have found a hardware erratum on 82599 hardware that can lead to
unpredictable behavior when Header Splitting mode is enabled. So
we are no longer enabling this feature on affected hardware.
Please see the 82599 Specification Update for more information.
CC: stable@kernel.org Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 5 Jan 2011 07:09:41 +0000 (07:09 +0000)]
ixgbe: fix variable set but not used warnings by gcc 4.6
Caught with gcc 4.6 -Wunused-but-set-variable
Remove unused napi_vectors variable.
Fix the use of reset_bit in ixgbe_reset_hw_X540()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Florian Fainelli [Mon, 24 Jan 2011 14:48:03 +0000 (14:48 +0000)]
e1000: add support for Marvell Alaska M88E1118R PHY
This patch adds support for Marvell Alask M88E188R PHY chips. Support for
other M88* PHYs is already there, so there is nothing more to add than its
PHY id.
e1000e: tx_timeout should not increment for non-hang events
Currently the driver increments the tx_timeout counter (an error counter)
when simply resetting the part with outstanding transmit work pending.
This is an unnecessary count of an error, when all we should be doing is
just resetting the part and discarding the transmits. With this change the
only increment of tx_timeout is when the stack calls the watchdog reset
function due to a true Tx timeout.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sven Eckelmann [Sun, 6 Feb 2011 23:26:43 +0000 (23:26 +0000)]
batman-adv: Linearize fragment packets before merge
We access the data inside the skbs of two fragments directly using memmove
during the merge. The data of the skb could span over multiple skb pages. An
direct access without knowledge about the pages would lead to an invalid memory
access.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[lindner_marek@yahoo.de: Move return from function to the end] Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
andrew hendry [Mon, 7 Feb 2011 00:08:15 +0000 (00:08 +0000)]
x25: possible skb leak on bad facilities
Originally x25_parse_facilities returned
-1 for an error
0 meaning 0 length facilities
>0 the length of the facilities parsed.
5ef41308f94dc ("x25: Prevent crashing when parsing bad X.25 facilities") introduced more
error checking in x25_parse_facilities however used 0 to indicate bad parsing a6331d6f9a429 ("memory corruption in X.25 facilities parsing") followed this further for
DTE facilities, again using 0 for bad parsing.
The meaning of 0 got confused in the callers.
If the facilities are messed up we can't determine where the data starts.
So patch makes all parsing errors return -1 and ensures callers close and don't use the skb further.
Reported-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Sat, 5 Feb 2011 22:48:37 +0000 (23:48 +0100)]
mac80211: as a 4-addr station, do not receive packets for other stations
Since 4-addr frames completely override the source address which will
make it into the converted 802.3 frames, receiving frames for other
4-addr stations will confuse the bridging code.
To be able to handle traffic for all connected devices, the bridge
code will automatically turn on promiscuous mode, which triggers
this problem.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Steve Brown <sbrown@cortland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Fri, 4 Feb 2011 23:30:24 +0000 (15:30 -0800)]
mac80211: Make some mlme timers module paramaters.
This allows users to tune the connection-loss algorithms
to be more or less lenient. In particular, larger
null-func retries helps when using lots of virtual
stations on a loaded network.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 7 Feb 2011 11:05:00 +0000 (12:05 +0100)]
mac80211: fix the skb cloned check in the tx path
Using skb_header_cloned to check if it's safe to write to the skb is not
enough - mac80211 also touches the tailroom of the skb.
Initially this check was only used to increase a counter, however this
commit changed the code to also skip skb data reallocation if no extra
head/tailroom was needed:
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Büsch [Fri, 4 Feb 2011 22:34:45 +0000 (23:34 +0100)]
ssb-pcmcia: Fix parsing of invariants tuples
This fixes parsing of the device invariants (MAC address)
for PCMCIA SSB devices.
ssb_pcmcia_do_get_invariants expects an iv pointer as data
argument.
Tested-by: dylan cristiani <d.cristiani@idem-tech.it> Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
enic: Clean up: Remove support for an older version of hardware
Remove support for an older version (A1) of hardware
Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
enic: Bug Fix: Reorder firmware devcmds - CMD_INIT and CMD_IG_VLAN_REWRITE_MODE
Firmware requires CMD_IG_VLAN_REWRITE_MODE be issued before a CMD_INIT.
Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
enic: Bug Fix: Fix return values of enic_add/del_station_addr routines
Fix enic_add/del_station_addr routines to return appropriate error code when an invalid address is added or deleted.
Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Organize the wrapper routines for firmware devcmds into a separate file.
Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Fri, 4 Feb 2011 12:57:16 +0000 (12:57 +0000)]
enic: Decouple mac address registration and deregistration from port profile set operation
This patch removes VM mac address registration and deregistration code during
port profile set operation. We can delay mac address registration until
enic_open.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 7 Feb 2011 08:38:55 +0000 (11:38 +0300)]
IPVS: precedence bug in ip_vs_sync_switch_mode()
'!' has higher precedence than '&'. IP_VS_STATE_MASTER is 0x1 so
the original code is equivelent to if (!ipvs->sync_state) ...
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com> Signed-off-by: Simon Horman <horms@verge.net.au>
Completed the bnx2x_set_rx_mode() to a proper netdev->ndo_set_rx_mode
implementation:
- Added a missing configuration of a unicast MAC addresses list.
- Changed bp->dma_lock from being a mutex to a spinlock as long as it's taken
under netdev->addr_list_lock now.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent packets duplication for frames targeting FCoE L2 ring:
packets were arriving to stack from both L2 RSS and from FCoE
L2 in a promiscuous mode.
Configure FCoE L2 ring to DROP_ALL rx mode, when interface is
configured to PROMISC, and to accept only unicast frames, when
interface is configured to ALL_MULTI.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Always configure an FCoE L2 ring with a mini-jumbo MTU size (2500).
To do that we had to move the rx_buf_size parameter from per
function level to a per ring level.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 4 Feb 2011 14:57:45 +0000 (06:57 -0800)]
iwlwifi: remove unnecessary locking
This code, and the places that set the variable
is_internal_short_scan and the vif pointers are
all protected by the mutex, there's no point in
locking the spinlock here as well (any more).
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Jesper Juhl [Sat, 5 Feb 2011 10:41:53 +0000 (10:41 +0000)]
sis900: Fix mem leak in sis900_rx error path
Fix memory leak in error path of sis900_rx(). If we don't do this we'll
leak the skb we dev_alloc_skb()'ed just a few lines above when the
variable goes out of scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 4 Feb 2011 22:37:30 +0000 (14:37 -0800)]
ipv4: Don't miss existing cached metrics in new routes.
Always lookup to see if we have an existing inetpeer entry for
a route. Let FLOWI_FLAG_PRECOW_METRICS merely influence the
"create" argument to rt_bind_peer().
Also, call rt_bind_peer() unconditionally since it is not
possible for rt->peer to be non-NULL at this point.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Greear [Fri, 4 Feb 2011 19:54:17 +0000 (11:54 -0800)]
mac80211: Optimize scans on current operating channel.
This should decrease un-necessary flushes, on/off channel work,
and channel changes in cases where the only scanned channel is
the current operating channel.
* Removes SCAN_OFF_CHANNEL flag, uses SDATA_STATE_OFFCHANNEL
and is-scanning flags instead.
* Add helper method to determine if we are currently configured
for the operating channel.
* Do no blindly go off/on channel in work.c Instead, only call
appropriate on/off code when we really need to change channels.
Always enable offchannel-ps mode when starting work,
and disable it when we are done.
* Consolidate ieee80211_offchannel_stop_station and
ieee80211_offchannel_stop_beaconing, call it
ieee80211_offchannel_stop_vifs instead.
* Accept non-beacon frames when scanning on operating channel.
* Scan state machine optimized to minimize on/off channel
transitions. Also, when going on-channel, go ahead and
re-enable beaconing. We're going to be there for 200ms,
so seems like some useful beaconing could happen.
Always enable offchannel-ps mode when starting software
scan, and disable it when we are done.
* Grab local->mtx earlier in __ieee80211_scan_completed_finish
so that we are protected when calling hw_config(), etc.
* Pass probe-responses up the stack if scanning on local
channel, so that mlme can take a look.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 4 Feb 2011 19:09:25 +0000 (20:09 +0100)]
ath9k: add additional checks for the baseband hang detection
Since even with the latest changes the false positive issue of the baseband
hang check is not fully solved yet, additional checks are needed.
If the baseband hang occurs, the rx_clear signal will be stuck to high, so
we can use the cycle counters to confirm it.
With this patch, a hardware reset is only triggered if the baseband hang
check returned true three times in a row, with a beacon interval between
each check and if the busy time was also 99% or more during the check
intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 4 Feb 2011 18:20:08 +0000 (19:20 +0100)]
mac80211: do not send duplicate data frames to the cooked monitor interface
I can't think of a valid use case for this aside from debugging (which can
also be done with a real monitor interface), and dropping these frames saves
some precious CPU cycles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 4 Feb 2011 11:51:28 +0000 (13:51 +0200)]
ath: Fix clearing of secondary key cache entry for TKIP
All register writes to the key cache have to be done in pairs. However,
the clearing of a separate MIC entry with hardware revisions that use
combined MIC key layout did not do that with one of the registers. Add
the matching register write to the following register to make the KEY4
register write actually complete.
This is mostly a fix for a theoretical issue since the incorrect entry
that could potentially be left behind in the key cache would not match
with received frames. Anyway, better make this code clean the entry
correctly using paired register writes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: do not restart ps timer during scan or offchannel
While leaving oper channel, STA informs sleep state to AP to
stop sending data. Till sending ack for the nullfunc, AP
continues to send the data to STA which restarts ps_timer that
is causing unnecessary nullfunc exchange on timer expiry
when the STA was already moved to offchannel. So don't restart ps_timer
on data reception during scan. This issue was identified by
the following warning.
WARNING: at net/mac80211/tx.c:661 invoke_tx_handlers+0xf07/0x1330 [mac80211]
wlan0: Dropped data frame as no usable bitrate found while scanning and
associated. Target station: 00:03:7f:0b:a6:1b on 5 GHz band
Call Trace:
[<ffffffffa0413ba7>] invoke_tx_handlers+0xf07/0x1330 [mac80211]
[<ffffffffa0414056>] ieee80211_tx+0x86/0x2c0 [mac80211]
[<ffffffffa0414345>] ieee80211_xmit+0xb5/0x1d0 [mac80211]
[<ffffffffa04037e0>] ieee80211_dynamic_ps_enable_work+0x0/0xb0 [mac80211]
[<ffffffffa04158cf>] ieee80211_tx_skb+0x4f/0x60 [mac80211]
[<ffffffffa04026e6>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]
[<ffffffffa0403885>] ieee80211_dynamic_ps_enable_work+0xa5/0xb0 [mac80211]
Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:50:02 +0000 (20:50 +0200)]
zd1211rw: reset device when CR_BCN_FIFO_SEMAPHORE freezes in beacon setup
When driver fails to acquire device semaphore lock, device usually
freezes soon afterwards. So failing to acquire lock indicates us that
not everything is going right in device/fw. So reset device when
this happens.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:49:52 +0000 (20:49 +0200)]
zd1211rw: add TX watchdog and device resetting
When doing transfers at high speed for long time, tx queue can freeze. So add
tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when
such is detected. Merely unlinking urb was not enough, device have to be
reseted. Hw settings are restored so that any open link will stay on after
reset.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:49:43 +0000 (20:49 +0200)]
zd1211rw: collect driver settings and add function to restore theim
We need HW hard reset later in patchset to reset device after TX-stall.
Collect all settings that we have set to driver for later reset and
add restore function.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:49:33 +0000 (20:49 +0200)]
zd1211rw: lower hw command timeouts
Device command timeouts are set up very high (1 sec) and this causes
AP beacon to lock up for long for example. Checking timeouts on device
it's easy to see that 1 sec timeout is not needed, when device fails
to response longer timeout doesn't help:
Jussi Kivilinna [Mon, 31 Jan 2011 18:49:05 +0000 (20:49 +0200)]
zd1211rw: batch beacon config commands together
Beacon config function writes beacon to hw one write per byte. This is very
slow (usually taking more than 100ms to finish) and causes high CPU usage
when in AP-mode (kworker at ~50% on Intel Atom N270). By batching commands
together zd_mac_config_beacon() runtime can be lowered to 1/5th and lower
CPU usage to saner levels (<10% on Atom).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:48:55 +0000 (20:48 +0200)]
zd1211rw: add beacon watchdog and setting HW beacon more failsafe
When doing tx/rx at high packet rate (for example simply using ping -f),
device starts to fail to respond to control messages. On non-AP modes
this only causes problems for LED updating code but when we are running
in AP-mode we are writing new beacon to HW usually every 100ms. Now if
control message fails in HW beacon setup, device lock is kept locked
and beacon data partially written. This can and usually does cause:
1. HW beacon setup fail now on, as driver cannot acquire device lock.
2. Beacon-done interrupt stop working as device has incomplete beacon.
Therefore make zd_mac_config_beacon() always try to release device lock
and add beacon watchdog to restart beaconing when stall is detected.
Also fix zd_mac_config_beacon() try acquiring device lock for max 500ms,
as what old code appeared to be trying to do using loop and msleep(1).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: fix race between next beacon dtim and ieee80211_get_buffered_bc
On review of 'zd1211rw: implement beacon fetching and handling
ieee80211_get_buffered_bc()', Christian Lamparter noted that [1]:
Since zd_beacon_done also uploads the next beacon so long in advance,
there could be an equally long race between the outdated state of the
next beacon's DTIM broadcast traffic indicator (802.11-2007 7.3.2.6)
which -in your case- was uploaded almost a beacon interval ago and
the xmit of ieee80211_get_buffered_bc *now*.
The dtim bc/mc bit might be not set, when a mc/bc arrived after the
beacon was uploaded, but before the "beacon done event" from the
hardware. So, dozing stations don't expect the broadcast traffic
and of course, they might miss it completely.
It's probably better to fix this in mac80211 (see the attached hack).
CC: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:48:16 +0000 (20:48 +0200)]
zd1211rw: fix ack_pending in filter_ack causing tx-packet ordering problem on monitor
For reasons not very clear yet to me, filter_ack leaves matching tx-packet
pending with 'ack_pending'. This causes tx-packet to be passed back to upper
layer after next packet has been transfered and tx-packets might end up
coming come out of monitor interface in wrong order vs. rx.
Because of this when enable AP-mode, hostapd monitor interface would get
packets in wrong order causing problems in WPA association.
So don't use mac->ack_pending when in AP-mode.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:47:36 +0000 (20:47 +0200)]
zd1211rw: fix beacon interval setup
Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon()
that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit
of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi()
appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16
and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags
and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval()
updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do
calculations on only lower u16 part of s->beacon_interval.
Also set 32bit beacon interval register before reading values from device,
as HW_EnableBeacon() on vendor driver does. This is required to make beacon
work on AP-mode, simply reading and then writing updated values is not enough
at least with zd1211b.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:47:17 +0000 (20:47 +0200)]
zd1211rw: cancel process_intr work on zd_chip_disable_int()
OOPS if worker is running and disconnect() is called (triggered
by unpluging device). Much harder to trigger at this stage but
later when we have AP beacon work in process_intr it happens very
easy.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 31 Jan 2011 18:47:08 +0000 (20:47 +0200)]
zd1211rw: use urb anchors for tx and fix tx-queue disabling
When stress testing AP-mode I hit OOPS when unpluging or rmmodding
driver.
It appears that when tx-queue is disabled, tx-urbs might be left pending.
These can cause ehci to call non-existing tx_urb_complete() (after rmmod)
or uninitialized/reseted private structure (after disconnect()). Add skb
queue for submitted packets and unlink pending urbs on zd_usb_disable_tx().
Part of the problem seems to be usb->free_urb_list that isn't always
working as it should, causing machine freeze when trying to free the list
in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem
to be doing (usbnet for example) so strip free_usb_list.
Patch makes tx-urb handling saner with use of urb anchors.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reverts the following commit
ath9k: remove bfs_paprd_timestamp from struct ath_buf_state
Under high interference/noisy environment conditions where PAPRD frames
fails heavily introduces a possibility of double freeing skb's and causes
kernel panic after some time.This patch reverts back to the original approach
of using paprd_timestamp before freeing the PAPRD frame skb's
Vasiliy Kulikov [Fri, 4 Feb 2011 02:23:50 +0000 (02:23 +0000)]
net: can: at91_can: world-writable sysfs files
Don't allow everybody to write to mb0_id file.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 4 Feb 2011 21:02:36 +0000 (13:02 -0800)]
bridge: Don't put partly initialized fdb into hash
The fdb_create() puts a new fdb into hash with only addr set. This is
not good, since there are callers, that search the hash w/o the lock
and access all the other its fields.
Applies to current netdev tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Francois Romieu [Thu, 3 Feb 2011 11:02:36 +0000 (12:02 +0100)]
r8169: RxFIFO overflow oddities with 8168 chipsets.
Some experiment-based action to prevent my 8168 chipsets locking-up hard
in the irq handler under load (pktgen ~1Mpps). Apparently a reset is not
always mandatory (is it at all ?).
- RTL_GIGA_MAC_VER_12
- RTL_GIGA_MAC_VER_25
Missed ~55% packets. Note:
- this is an old SiS 965L motherboard
- the 8168 chipset emits (lots of) control frames towards the sender
- RTL_GIGA_MAC_VER_26
The chipset does not go into a frenzy of mac control pause when it
crashes yet but it can still be crashed. It needs more work.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Ivan Vecera <ivecera@redhat.com> Cc: Hayes <hayeswang@realtek.com>
Ivan Vecera [Thu, 27 Jan 2011 11:24:11 +0000 (12:24 +0100)]
r8169: use RxFIFO overflow workaround for 8168c chipset.
I found that one of the 8168c chipsets (concretely XID 1c4000c0) starts
generating RxFIFO overflow errors. The result is an infinite loop in
interrupt handler as the RxFIFOOver is handled only for ...MAC_VER_11.
With the workaround everything goes fine.
Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Hayes <hayeswang@realtek.com>
projects / mv-sheeva.git / log