Shengzhou Liu [Wed, 25 Dec 2013 10:06:56 +0000 (18:06 +0800)]
powerpc/fsl_pci: add versionless pci compatible
There are much pci compatible with version on existing platforms.
To stop putting version numbers in device tree later, we add a
generic compatible 'fsl,qoriq-pcie'.
The version number is readable directly from a register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Shengzhou Liu [Wed, 25 Dec 2013 10:06:55 +0000 (18:06 +0800)]
powerpc/85xx/dts: add third elo3 dma component
Add elo3-dma-2.dtsi to support the third DMA controller.
This is used on T2080, T4240, B4860, etc.
FSL MPIC v4.3 adds a new discontiguous address range for internal interrupts,
e.g. internal interrupt 0 is at offset 0x200 and thus interrupt number is:
0x200 >> 5 = 16 in the device tree. DMA controller 3 channel 0 internal
interrupt 240 is at offset 0x3a00, and thus the corresponding interrupt
number is: 0x3a00 >> 5 = 464, it's similar for other 7 interrupt numbers
of DMA 3 channels.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Diana Craciun [Thu, 14 Mar 2013 14:55:11 +0000 (16:55 +0200)]
powerpc: Replaced tlbilx with tlbwe in the initialization code
On Freescale e6500 cores EPCR[DGTMI] controls whether guest supervisor
state can execute TLB management instructions. If EPCR[DGTMI]=0
tlbwe and tlbilx are allowed to execute normally in the guest state.
A hypervisor may choose to virtualize TLB1 and for this purpose it
may use IPROT to protect the entries for being invalidated by the
guest. However, because tlbwe and tlbilx execution in the guest state
are sharing the same bit, it is not possible to have a scenario where
tlbwe is allowed to be executed in guest state and tlbilx traps. When
guest TLB management instructions are allowed to be executed in guest
state the guest cannot use tlbilx to invalidate TLB1 guest entries.
Linux is using tlbilx in the boot code to invalidate the temporary
entries it creates when initializing the MMU. The patch is replacing
the usage of tlbilx in initialization code with tlbwe with VALID bit
cleared.
Linux is also using tlbilx in other contexts (like huge pages or
indirect entries) but removing the tlbilx from the initialization code
offers the possibility to have scenarios under hypervisor which are
not using huge pages or indirect entries.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Tue, 12 Jun 2012 22:02:32 +0000 (17:02 -0500)]
powerpc/booke-64: fix tlbsrx. path in bolted tlb handler
It was branching to the cleanup part of the non-bolted handler,
which would have been bad if there were any chips with tlbsrx.
that use the bolted handler.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Paul Gortmaker [Thu, 9 Jan 2014 20:33:35 +0000 (15:33 -0500)]
powerpc: fix 8xx and 6xx final link failures
As of commit b81f18e55e9f4ea81759bcb00fea295de679bbe8 ("powerpc/boot:
Only build board support files when required.") the two defconfigs
ep88xc_defconfig and storcenter_defconfig would fail final link as
follows:
WRAP arch/powerpc/boot/dtbImage.ep88xc
arch/powerpc/boot/wrapper.a(mpc8xx.o): In function `mpc885_get_clock':
arch/powerpc/boot/mpc8xx.c:30: undefined reference to `fsl_get_immr'
make[1]: *** [arch/powerpc/boot/dtbImage.ep88xc] Error 1
...and...
WRAP arch/powerpc/boot/cuImage.storcenter
arch/powerpc/boot/cuboot-pq2.o: In function `pq2_platform_fixups':
cuboot-pq2.c:(.text+0x324): undefined reference to `fsl_get_immr'
make[1]: *** [arch/powerpc/boot/cuImage.storcenter] Error 1
We need the fsl-soc board files built for these two platforms.
Cc: Tony Breeds <tony@bakeyournoodle.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Fixes: b81f18e55e9f ("powerpc/boot: Only build board support files when required.") Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Shaohui Xie [Tue, 7 Jan 2014 06:27:41 +0000 (14:27 +0800)]
powerpc/85xx: handle the eLBC error interrupt if it exists in dts
On P1020, P1021, P1022, and P1023, eLBC event interrupts are routed
to internal interrupt 3 while ELBC error interrupts are routed to
internal interrupt 0. We need to call request_irq for each.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
[scottwood@freescale.com: reworded commit message and fixed author] Signed-off-by: Scott Wood <scottwood@freescale.com>
Wang Dongsheng [Tue, 7 Jan 2014 06:26:42 +0000 (14:26 +0800)]
powerpc/dts: fix lbc lack of error interrupt
P1020, P1021, P1022, P1023 when the lbc get error, the error
interrupt will be triggered. The corresponding interrupt is
internal IRQ0. So system have to process the lbc IRQ0 interrupt.
The corresponding lbc general interrupt is internal IRQ3.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[scottwood@freescale.com: bracketed individual list elements] Signed-off-by: Scott Wood <scottwood@freescale.com>
Stephen Chivers [Thu, 9 Jan 2014 02:01:22 +0000 (13:01 +1100)]
powerpc/embedded6xx: Add support for Motorola/Emerson MVME5100
Add support for the Motorola/Emerson MVME5100 Single Board Computer.
The MVME5100 is a 6U form factor VME64 computer with:
- A single MPC7410 or MPC750 CPU
- A HAWK Processor Host Bridge (CPU to PCI) and
MultiProcessor Interrupt Controller (MPIC)
- Up to 500Mb of onboard memory
- A M48T37 Real Time Clock (RTC) and Non-Volatile Memory chip
- Two 16550 compatible UARTS
- Two Intel E100 Fast Ethernets
- Two PCI Mezzanine Card (PMC) Slots
- PPCBug Firmware
The HAWK PHB/MPIC is compatible with the MPC10x devices.
There is no onboard disk support. This is usually provided by installing a PMC
in first PMC slot.
This patch revives the board support, it was present in early 2.6
series kernels. The board support in those days was by Matt Porter of
MontaVista Software.
CSC Australia has around 31 of these boards in service. The kernel in use
for the boards is based on 2.6.31. The boards are operated without disks
from a file server.
This patch is based on linux-3.13-rc2 and has been boot tested.
Only boards with 512 Mb of memory are known to work.
Signed-off-by: Stephen Chivers <schivers@csc.com> Tested-by: Alessio Igor Bogani <alessio.bogani@elettra.eu> Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Sat, 12 Oct 2013 00:22:39 +0000 (19:22 -0500)]
powerpc/fsl-book3e-64: Use paca for hugetlb TLB1 entry selection
This keeps usage coordinated for hugetlb and indirect entries, which
should make entry selection more predictable and probably improve overall
performance when mixing the two.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Sat, 12 Oct 2013 00:22:38 +0000 (19:22 -0500)]
powerpc/e6500: TLB miss handler with hardware tablewalk support
There are a few things that make the existing hw tablewalk handlers
unsuitable for e6500:
- Indirect entries go in TLB1 (though the resulting direct entries go in
TLB0).
- It has threads, but no "tlbsrx." -- so we need a spinlock and
a normal "tlbsx". Because we need this lock, hardware tablewalk
is mandatory on e6500 unless we want to add spinlock+tlbsx to
the normal bolted TLB miss handler.
- TLB1 has no HES (nor next-victim hint) so we need software round robin
(TODO: integrate this round robin data with hugetlb/KVM)
- The existing tablewalk handlers map half of a page table at a time,
because IBM hardware has a fixed 1MiB indirect page size. e6500
has variable size indirect entries, with a minimum of 2MiB.
So we can't do the half-page indirect mapping, and even if we
could it would be less efficient than mapping the full page.
- Like on e5500, the linear mapping is bolted, so we don't need the
overhead of supporting nested tlb misses.
Note that hardware tablewalk does not work in rev1 of e6500.
We do not expect to support e6500 rev1 in mainline Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Mihai Caraman <mihai.caraman@freescale.com>
Scott Wood [Sat, 12 Oct 2013 00:22:37 +0000 (19:22 -0500)]
powerpc: add barrier after writing kernel PTE
There is no barrier between something like ioremap() writing to
a PTE, and returning the value to a caller that may then store the
pointer in a place that is visible to other CPUs. Such callers
generally don't perform barriers of their own.
Even if callers of ioremap() and similar things did use barriers,
the most logical choise would be smp_wmb(), which is not
architecturally sufficient when BookE hardware tablewalk is used. A
full sync is specified by the architecture.
For userspace mappings, OTOH, we generally already have an lwsync due
to locking, and if we occasionally take a spurious fault due to not
having a full sync with hardware tablewalk, it will not be fatal
because we will retry rather than oops.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Tue, 24 Dec 2013 07:12:12 +0000 (15:12 +0800)]
powerpc/fsl_booke: enable the relocatable for the kdump kernel
The RELOCATABLE is more flexible and without any alignment restriction.
And it is a superset of DYNAMIC_MEMSTART. So use it by default for
a kdump kernel.
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Tue, 24 Dec 2013 07:12:11 +0000 (15:12 +0800)]
powerpc/fsl_booke: smp support for booting a relocatable kernel above 64M
When booting above the 64M for a secondary cpu, we also face the
same issue as the boot cpu that the PAGE_OFFSET map two different
physical address for the init tlb and the final map. So we have to use
switch_to_as1/restore_to_as0 between the conversion of these two
maps. When restoring to as0 for a secondary cpu, we only need to
return to the caller. So add a new parameter for function
restore_to_as0 for this purpose.
Use LOAD_REG_ADDR_PIC to get the address of variables which may
be used before we set the final map in cams for the secondary cpu.
Move the setting of cams a bit earlier in order to avoid the
unnecessary using of LOAD_REG_ADDR_PIC.
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Tue, 24 Dec 2013 07:12:10 +0000 (15:12 +0800)]
powerpc/fsl_booke: make sure PAGE_OFFSET map to memstart_addr for relocatable kernel
This is always true for a non-relocatable kernel. Otherwise the kernel
would get stuck. But for a relocatable kernel, it seems a little
complicated. When booting a relocatable kernel, we just align the
kernel start addr to 64M and map the PAGE_OFFSET from there. The
relocation will base on this virtual address. But if this address
is not the same as the memstart_addr, we will have to change the
map of PAGE_OFFSET to the real memstart_addr and do another relocation
again.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[scottwood@freescale.com: make offset long and non-negative in simple case] Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Tue, 24 Dec 2013 07:12:08 +0000 (15:12 +0800)]
powerpc: introduce early_get_first_memblock_info
For a relocatable kernel since it can be loaded at any place, there
is no any relation between the kernel start addr and the memstart_addr.
So we can't calculate the memstart_addr from kernel start addr. And
also we can't wait to do the relocation after we get the real
memstart_addr from device tree because it is so late. So introduce
a new function we can use to get the first memblock address and size
in a very early stage (before machine_init).
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Tue, 24 Dec 2013 07:12:07 +0000 (15:12 +0800)]
powerpc/fsl_booke: set the tlb entry for the kernel address in AS1
We use the tlb1 entries to map low mem to the kernel space. In the
current code, it assumes that the first tlb entry would cover the
kernel image. But this is not true for some special cases, such as
when we run a relocatable kernel above the 64M or set
CONFIG_KERNEL_START above 64M. So we choose to switch to address
space 1 before setting these tlb entries.
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Tue, 24 Dec 2013 07:12:06 +0000 (15:12 +0800)]
powerpc: enable the relocatable support for the fsl booke 32bit kernel
This is based on the codes in the head_44x.S. The difference is that
the init tlb size we used is 64M. With this patch we can only load the
kernel at address between memstart_addr ~ memstart_addr + 64M. We will
fix this restriction in the following patches.
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Tue, 24 Dec 2013 07:12:03 +0000 (15:12 +0800)]
powerpc/fsl_booke: protect the access to MAS7
The e500v1 doesn't implement the MAS7, so we should avoid to access
this register on that implementations. In the current kernel, the
access to MAS7 are protected by either CONFIG_PHYS_64BIT or
MMU_FTR_BIG_PHYS. Since some code are executed before the code
patching, we have to use CONFIG_PHYS_64BIT in these cases.
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Set wait time interface:(Nanosecond)
/sys/devices/system/cpu/cpuX/pw20_wait_time
/sys/devices/system/cpu/cpuX/altivec_idle_wait_time
Example: Base on TBfreq is 41MHZ.
1~48(ns): TB[63]
49~97(ns): TB[62]
98~195(ns): TB[61]
196~390(ns): TB[60]
391~780(ns): TB[59]
781~1560(ns): TB[58]
...
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[scottwood@freescale.com: change ifdef] Signed-off-by: Scott Wood <scottwood@freescale.com>
Wang Dongsheng [Tue, 17 Dec 2013 08:17:01 +0000 (16:17 +0800)]
powerpc/85xx: add hardware automatically enter pw20 state
Using hardware features make core automatically enter PW20 state.
Set a TB count to hardware, the effective count begins when PW10
is entered. When the effective period has expired, the core will
proceed from PW10 to PW20 if no exit conditions have occurred during
the period.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Wang Dongsheng [Tue, 17 Dec 2013 08:17:00 +0000 (16:17 +0800)]
powerpc/85xx: add hardware automatically enter altivec idle state
Each core's AltiVec unit may be placed into a power savings mode
by turning off power to the unit. Core hardware will automatically
power down the AltiVec unit after no AltiVec instructions have
executed in N cycles. The AltiVec power-control is triggered by hardware.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Xie Xiaobo [Wed, 6 Nov 2013 09:08:03 +0000 (17:08 +0800)]
powerpc/85xx: Add TWR-P1025 board support
TWR-P1025 Overview
-----------------
512Mbyte DDR3 (on board DDR)
64MB Nor Flash
eTSEC1: Connected to RGMII PHY AR8035
eTSEC3: Connected to RGMII PHY AR8035
Two USB2.0 Type A
One microSD Card slot
One mini-PCIe slot
One mini-USB TypeB dual UART
Signed-off-by: Michael Johnston <michael.johnston@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[scottwood@freescale.com: use pr_info rather than KERN_INFO] Signed-off-by: Scott Wood <scottwood@freescale.com>
Lijun Pan [Fri, 15 Nov 2013 23:28:20 +0000 (17:28 -0600)]
powerpc/85xx: Merge 85xx/p1023_defconfig into mpc85xx_smp and mpc85xx
mpc85xx_smp_defconfig and mpc85xx_defconfig already have CONFIG_P1023RDS=y.
Merge CONFIG_P1023RDB=y and other relevant configurations into
mpc85xx_smp_defconfig and mpc85_defconfig.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Thu, 2 Jan 2014 22:37:50 +0000 (16:37 -0600)]
powerpc/fsl-booke: Use SPRN_SPRGn rather than mfsprg/mtsprg
This fixes a build break that was probably introduced with the removal
of -Wa,-me500 (commit f49596a4cf4753d13951608f24f939a59fdcc653), where
the assembler refuses to recognize SPRG4-7 with a generic PPC target.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Dongsheng Wang <dongsheng.wang@freescale.com> Cc: Anton Vorontsov <avorontsov@mvista.com> Reviewed-by: Wang Dongsheng <dongsheng.wang@freescale.com> Tested-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Kevin Hao [Thu, 7 Nov 2013 07:17:17 +0000 (15:17 +0800)]
powerpc/85xx: don't init the mpic ipi for the SoC which has doorbell support
It makes no sense to initialize the mpic ipi for the SoC which has
doorbell support. So set the smp_85xx_ops.probe to NULL for this
case. Since the smp_85xx_ops.probe is also used in function
smp_85xx_setup_cpu() to check if we need to invoke
mpic_setup_this_cpu(), we introduce a new setup_cpu function
smp_85xx_basic_setup() to remove this dependency.
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Zhao Qiang [Thu, 7 Nov 2013 02:29:29 +0000 (10:29 +0800)]
powerpc/p1010rdb:update mtd of nand to adapt to both old and new p1010rdb
P1010rdb-pa and p1010rdb-pb have different mtd of nand.
So update dts to adapt to both p1010rdb-pa and p1010rdb-pb.
Move the nand-mtd from p1010rdb.dtsi to p1010rdb-pa*.dts.
Remove nand-mtd for p1010rdb-pb, whick will use mtdparts
from u-boot instead of nand-mtd in device tree.
Signed-off-by: Zhao Qiang <B45475@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Joseph Myers [Mon, 4 Nov 2013 16:55:05 +0000 (16:55 +0000)]
powerpc: fix e500 SPE float SIGFPE generation
The e500 SPE floating-point emulation code is called from
SPEFloatingPointException and SPEFloatingPointRoundException in
arch/powerpc/kernel/traps.c. Those functions have support for
generating SIGFPE, but do_spe_mathemu and speround_handler don't
generate a return value to indicate that this should be done. Such a
return value should depend on whether an exception is raised that has
been set via prctl to generate SIGFPE. This patch adds the relevant
logic in these functions so that SIGFPE is generated as expected by
the glibc testsuite.
Signed-off-by: Joseph Myers <joseph@codesourcery.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Joseph Myers [Mon, 4 Nov 2013 16:54:46 +0000 (16:54 +0000)]
powerpc: fix e500 SPE float to integer and fixed-point conversions
The e500 SPE floating-point emulation code has several problems in how
it handles conversions to integer and fixed-point fractional types.
There are the following 20 relevant instructions. These can convert
to signed or unsigned 32-bit integers, either rounding towards zero
(as correct for C casts from floating-point to integer) or according
to the current rounding mode, or to signed or unsigned 32-bit
fixed-point values (values in the range [-1, 1) or [0, 1)). For
conversion from double precision there are also instructions to
convert to 64-bit integers, rounding towards zero, although as far as
I know those instructions are completely theoretical (they are only
defined for implementations that support both SPE and classic 64-bit,
and I'm not aware of any such hardware even though the architecture
definition permits that combination).
The emulation code, for the instructions that come in variants
rounding either towards zero or according to the current rounding
direction, uses "if (func & 0x4)" as a condition for using _FP_ROUND
(otherwise _FP_ROUND_ZERO is used). The condition is correct, but the
code it controls isn't. Whether _FP_ROUND or _FP_ROUND_ZERO is used
makes no difference, as the effect of those soft-fp macros is to round
an intermediate floating-point result using the low three bits (the
last one sticky) of the working format. As these operations are
dealing with a freshly unpacked floating-point input, those low bits
are zero and no rounding occurs. The emulation code then uses the
FP_TO_INT_* macros for the actual integer conversion, with the effect
of always rounding towards zero; for rounding according to the current
rounding direction, it should be using FP_TO_INT_ROUND_*.
The instructions in question have semantics defined (in the Power ISA
documents) for out-of-range values and NaNs: out-of-range values
saturate and NaNs are converted to zero. The emulation does nothing
to follow those semantics for NaNs (the soft-fp handling is to treat
them as infinities), and messes up the saturation semantics. For
single-precision conversion to integers, (((func & 0x3) != 0) || SB_s)
is the condition used for doing a signed conversion. The first part
is correct, but the second isn't: negative numbers should result in
saturation to 0 when converted to unsigned. Double-precision
conversion to 64-bit integers correctly uses ((func & 0x1) == 0).
Double-precision conversion to 32-bit integers uses (((func & 0x3) !=
0) || DB_s), with correct first part and incorrect second part. And
vector float conversion to integers uses (((func & 0x3) != 0) ||
SB0_s) (and similar for the other vector element), where the sign bit
check is again wrong.
The incorrect handling of negative numbers converted to unsigned was
introduced in commit afc0a07d4a283599ac3a6a31d7454e9baaeccca0. The
rationale given there was a C testcase with cast from float to
unsigned int. Conversion of out-of-range floating-point numbers to
integer types in C is undefined behavior in the base standard, defined
in Annex F to produce an unspecified value. That is, the C testcase
used to justify that patch is incorrect - there is no ISO C
requirement for a particular value resulting from this conversion -
and in any case, the correct semantics for such emulation are the
semantics for the instruction (unsigned saturation, which is what it
does in hardware when the emulation is disabled).
The conversion to fixed-point values has its own problems. That code
doesn't try to do a full emulation; it relies on the trap handler only
being called for arguments that are infinities, NaNs, subnormal or out
of range. That's fine, but the logic ((vb.wp[1] >> 23) == 0xff &&
((vb.wp[1] & 0x7fffff) > 0)) for NaN detection won't detect negative
NaNs as being NaNs (the same applies for the double-precision case),
and subnormals are mapped to 0 rather than respecting the rounding
mode; the code should also explicitly raise the "invalid" exception.
The code for vectors works by executing the scalar float instruction
with the trapping disabled, meaning at least subnormals won't be
handled correctly.
As well as all those problems in the main emulation code, the rounding
handler - used to emulate rounding upward and downward when not
supported in hardware and when no higher priority exception occurred -
has its own problems.
* It gets called in some cases even for the instructions rounding to
zero, and then acts according to the current rounding mode when it
should just leave alone the truncated result provided by hardware.
* It presumes that the result is a single-precision, double-precision
or single-precision vector as appropriate for the instruction type,
determines the sign of the result accordingly, and then adjusts the
result based on that sign and the rounding mode.
- In the single-precision cases at least the sign determination for
an integer result is the same as for a floating-point result; in
the double-precision case, converted to 32-bit integer or fixed
point, the sign of a double-precision value is in the high part of
the register but it's the low part of the register that has the
result of the conversion.
- If the result is unsigned fixed-point, its sign may be wrongly
determined as negative (does not actually cause problems, because
inexact unsigned fixed-point results with the high bit set can
only appear when converting from double, in which case the sign
determination is instead wrongly using the high part of the
register).
- If the sign of the result is correctly determined as negative, any
adjustment required to change the truncated result to one correct
for the rounding mode should be in the opposite direction for
two's-complement integers as for sign-magnitude floating-point
values.
- And if the integer result is zero, the correct sign can only be
determined by examining the original operand, and not at all (as
far as I can tell) if the operand and result are the same
register.
This patch fixes all these problems (as far as possible, given the
inability to determine the correct sign in the rounding handler when
the truncated result is 0, the conversion is to a signed type and the
truncated result has overwritten the original operand). Conversion to
fixed-point now uses full emulation, and does not use "asm" in the
vector case; the semantics are exactly those of converting to integer
according to the current rounding direction, once the exponent has
been adjusted, so the code makes such an adjustment then uses the
FP_TO_INT_ROUND macros.
The testcase I used for verifying that the instructions (other than
the theoretical conversions to 64-bit integers) produce the correct
results is at <http://lkml.org/lkml/2013/10/8/708>.
Signed-off-by: Joseph Myers <joseph@codesourcery.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Joseph Myers [Mon, 4 Nov 2013 16:54:15 +0000 (16:54 +0000)]
math-emu: fix floating-point to integer overflow detection
On overflow, the math-emu macro _FP_TO_INT_ROUND tries to saturate its
result (subject to the value of rsigned specifying the desired
overflow semantics). However, if the rounding step has the effect of
increasing the exponent so as to cause overflow (if the rounded result
is 1 larger than the largest positive value with the given number of
bits, allowing for signedness), the overflow does not get detected,
meaning that for unsigned results 0 is produced instead of the maximum
unsigned integer with the give number of bits, without an exception
being raised for overflow, and that for signed results the minimum
(negative) value is produced instead of the maximum (positive) value,
again without an exception. This patch makes the code check for
rounding increasing the exponent and adjusts the exponent value as
needed for the overflow check.
Signed-off-by: Joseph Myers <joseph@codesourcery.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Joseph Myers [Mon, 4 Nov 2013 16:53:50 +0000 (16:53 +0000)]
math-emu: fix floating-point to integer unsigned saturation
The math-emu macros _FP_TO_INT and _FP_TO_INT_ROUND are supposed to
saturate their results for out-of-range arguments, except in the case
rsigned == 2 (when instead the low bits of the result are taken).
However, in the case rsigned == 0 (converting to unsigned integers),
they mistakenly produce 0 for positive results and the maximum
unsigned integer for negative results, the opposite of correct
unsigned saturation. This patch fixes the logic.
Signed-off-by: Joseph Myers <joseph@codesourcery.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
The e500 SPE floating-point emulation code for the rounding modes
rounding to positive or negative infinity (which may not be
implemented in hardware) tries to avoid emulating rounding if the
result was inexact. However, it tests inexactness using the sticky
bit with the cumulative result of previous operations, rather than
with the non-sticky bits relating to the operation that generated the
interrupt. Furthermore, when a vector operation generates the
interrupt, it's possible that only one of the low and high parts is
inexact, and so only that part should have rounding emulated. This
results in incorrect rounding of exact results in these modes when the
sticky bit is set from a previous operation.
(I'm not sure why the rounding interrupts are generated at all when
the result is exact, but empirically the hardware does generate them.)
This patch checks for inexactness using the correct bits of SPEFSCR,
and ensures that rounding only occurs when the relevant part of the
result was actually inexact.
Signed-off-by: Joseph Myers <joseph@codesourcery.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Joseph Myers [Tue, 10 Dec 2013 23:07:45 +0000 (23:07 +0000)]
powerpc: fix exception clearing in e500 SPE float emulation
The e500 SPE floating-point emulation code clears existing exceptions
(__FPU_FPSCR &= ~FP_EX_MASK;) before ORing in the exceptions from the
emulated operation. However, these exception bits are the "sticky",
cumulative exception bits, and should only be cleared by the user
program setting SPEFSCR, not implicitly by any floating-point
instruction (whether executed purely by the hardware or emulated).
The spurious clearing of these bits shows up as missing exceptions in
glibc testing.
Fixing this, however, is not as simple as just not clearing the bits,
because while the bits may be from previous floating-point operations
(in which case they should not be cleared), the processor can also set
the sticky bits itself before the interrupt for an exception occurs,
and this can happen in cases when IEEE 754 semantics are that the
sticky bit should not be set. Specifically, the "invalid" sticky bit
is set in various cases with non-finite operands, where IEEE 754
semantics do not involve raising such an exception, and the
"underflow" sticky bit is set in cases of exact underflow, whereas
IEEE 754 semantics are that this flag is set only for inexact
underflow. Thus, for correct emulation the kernel needs to know the
setting of these two sticky bits before the instruction being
emulated.
When a floating-point operation raises an exception, the kernel can
note the state of the sticky bits immediately afterwards. Some
<fenv.h> functions that affect the state of these bits, such as
fesetenv and feholdexcept, need to use prctl with PR_GET_FPEXC and
PR_SET_FPEXC anyway, and so it is natural to record the state of those
bits during that call into the kernel and so avoid any need for a
separate call into the kernel to inform it of a change to those bits.
Thus, the interface I chose to use (in this patch and the glibc port)
is that one of those prctl calls must be made after any userspace
change to those sticky bits, other than through a floating-point
operation that traps into the kernel anyway. feclearexcept and
fesetexceptflag duly make those calls, which would not be required
were it not for this issue.
The previous EGLIBC port, and the uClibc code copied from it, is
fundamentally broken as regards any use of prctl for floating-point
exceptions because it didn't use the PR_FP_EXC_SW_ENABLE bit in its
prctl calls (and did various worse things, such as passing a pointer
when prctl expected an integer). If you avoid anything where prctl is
used, the clearing of sticky bits still means it will never give
anything approximating correct exception semantics with existing
kernels. I don't believe the patch makes things any worse for
existing code that doesn't try to inform the kernel of changes to
sticky bits - such code may get incorrect exceptions in some cases,
but it would have done so anyway in other cases.
Signed-off-by: Joseph Myers <joseph@codesourcery.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Mihai Caraman [Thu, 8 Aug 2013 12:56:09 +0000 (15:56 +0300)]
powerpc/booke64: Add LRAT error exception handler
LRAT (Logical to Real Address Translation) present in MMU v2 provides hardware
translation from a logical page number (LPN) to a real page number (RPN) when
tlbwe is executed by a guest or when a page table translation occurs from a
guest virtual address.
Add LRAT error exception handler to Booke3E 64-bit kernel and the basic KVM
handler to avoid build breakage. This is a prerequisite for KVM LRAT support
that will follow.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Alistair Popple [Mon, 9 Dec 2013 07:17:01 +0000 (18:17 +1100)]
powerpc/iommu: Update constant names to reflect their hardcoded page size
The powerpc iommu uses a hardcoded page size of 4K. This patch changes
the name of the IOMMU_PAGE_* macros to reflect the hardcoded values. A
future patch will use the existing names to support dynamic page
sizes.
powerpc: Fix "attempt to move .org backwards" error
With recent machine check patch series changes, The exception vectors
starting from 0x4300 are now overflowing with allyesconfig. Fix that by
moving machine_check_common and machine_check_handle_early code out of
that region to make enough room for exception vector area.
Fixes this build error reportes by Stephen:
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:958: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:959: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:983: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:984: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1003: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1013: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1014: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1015: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1016: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1017: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1018: Error: attempt to move .org backwards
[Moved the code further down as it introduced link errors due to too long
relative branches to the masked interrupts handlers from the exception
prologs. Also removed the useless feature section --BenH
]
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Olof Johansson [Sat, 28 Dec 2013 21:01:47 +0000 (13:01 -0800)]
powerpc: Fix alignment of secondary cpu spin vars
Commit 5c0484e25ec0 ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.
This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.
Fix is to add explicit alignment instead of relying on good luck. :)
[ It appears that there is a different issue with PA Semi systems
however this fix is definitely correct so applying anyway -- BenH
]
Fixes: 5c0484e25ec0 ('powerpc: Endian safe trampoline') Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811 Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Mon, 23 Dec 2013 01:19:51 +0000 (12:19 +1100)]
powerpc: Align p_end
p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.
This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Fri, 20 Dec 2013 19:06:01 +0000 (13:06 -0600)]
powernv/eeh: Add buffer for P7IOC hub error data
Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data. Take care to inform OPAL of
the correct size for the buffer.
[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com> Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Thu, 19 Dec 2013 23:14:07 +0000 (17:14 -0600)]
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com> Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul E. McKenney [Tue, 17 Dec 2013 22:29:57 +0000 (09:29 +1100)]
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
The powerpc 64-bit __copy_tofrom_user() function uses shifts to handle
unaligned invocations. However, these shifts were designed for
big-endian systems: On little-endian systems, they must shift in the
opposite direction.
This commit relies on the C preprocessor to insert the correct shifts
into the assembly code.
[ This is a rare but nasty LE issue. Most of the time we use the POWER7
optimised __copy_tofrom_user_power7 loop, but when it hits an exception
we fall back to the base __copy_tofrom_user loop. - Anton ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Make unaligned accesses endian-safe for powerpc
The generic put_unaligned/get_unaligned macros were made endian-safe by
calling the appropriate endian dependent macros based on the endian type
of the powerpc processor.
Signed-off-by: Rajesh B Prathipati <rprathip@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 16 Dec 2013 04:12:43 +0000 (15:12 +1100)]
powerpc: Fix bad stack check in exception entry
In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel. If it's not valid, we die but
with a nice oops message.
Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative. Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.
This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE. With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.
Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the USB controller's pin muxing is not setup
correctly and causes a kernel panic upon system startup, so
disable the USB1 device tree node in the MPC5125 tower board
dts file.
The USB controller is connected to an USB3320 ULPI transceiver
and the device tree should receive an update to reflect correct
dependencies and required initialization data before the USB1
node can get re-enabled.
Gerhard Sittig [Tue, 10 Dec 2013 09:51:08 +0000 (10:51 +0100)]
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node (5125)
the 'soc' node in the MPC5125 "tower" board .dts has an '#interrupt-cells'
property although this node is not an interrupt controller
remove this erroneously placed property because starting with v3.13-rc1
lookup and resolution of 'interrupts' specs for peripherals gets misled
(tries to use the 'soc' as the interrupt parent which fails), emits
'no irq domain found' WARN() messages and breaks the boot process
[ best viewed with 'git diff -U5' to have DT node names in the context ]
Ulrich Weigand [Thu, 12 Dec 2013 04:59:34 +0000 (15:59 +1100)]
powerpc: PTRACE_PEEKUSR always returns FPR0
There is a bug in using ptrace to access FPRs via PTRACE_PEEKUSR /
PTRACE_POKEUSR. In effect, trying to access any of the FPRs always
really accesses FPR0, which does seriously break debugging :-)
The problem seems to have been introduced by commit 3ad26e5c4459d
(Merge branch 'for-kvm' into next).
[ It is indeed a merge conflict between Paul's FPU/VSX state rework
and my LE patches - Anton ]
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current logic sets the kdump base to min of 2G or ppc64_rma_size/2.
On PowerNV kernel the first memory block 'memory@0' can be very large,
equal to the DIMM size with ppc64_rma_size value capped to 1G. Hence on
PowerNV, kdump base is set to 512M resulting kdump to fail while allocating
paca array. This is because, paca need its memory from RMA region capped
at 256M (see allocate_pacas()).
This patch lowers the kdump base cap to 128M so that kdump kernel can
successfully get memory below 256M for paca allocation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have recently found out that no iommu_groups could be found under
/sys/ on a P8. That prevents PCI passthrough from working.
During my investigation, I found out there seems to be a missing
iommu_register_group for PHB3. The following patch seems to fix the
problem. After applying it, I see iommu_groups under
/sys/kernel/iommu_groups/, and can also bind vfio-pci to an adapter,
which gives me a device at /dev/vfio/.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/52xx: Re-enable bestcomm driver in defconfigs
The bestcomm driver has been moved to drivers/dma, so to select
this driver by default additionally CONFIG_DMADEVICES has to be
enabled. Currently it is not enabled in the config despite existing
CONFIG_PPC_BESTCOMM=y in the config files. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Hong H. Pham [Sat, 7 Dec 2013 14:06:33 +0000 (09:06 -0500)]
powerpc: Fix PTE page address mismatch in pgtable ctor/dtor
In pte_alloc_one(), pgtable_page_ctor() is passed an address that has
not been converted by page_address() to the newly allocated PTE page.
When the PTE is freed, __pte_free_tlb() calls pgtable_page_dtor()
with an address to the PTE page that has been converted by page_address().
The mismatch in the PTE's page address causes pgtable_page_dtor() to access
invalid memory, so resources for that PTE (such as the page lock) is not
properly cleaned up.
On PPC32, only SMP kernels are affected.
On PPC64, only SMP kernels with 4K page size are affected.
On a preempt-rt kernel, a spinlock is dynamically allocated for each
PTE in pgtable_page_ctor(). When the PTE is freed, calling
pgtable_page_dtor() with a mismatched page address causes a memory leak,
as the pointer to the PTE's spinlock is bogus.
On mainline, there isn't any immediately obvious symptoms, but the
problem still exists here.
Fixes: d614bb041209fd7c "powerpc: Move the pte free routes from common header" Cc: Paul Mackerras <paulus@samba.org> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linux-stable <stable@vger.kernel.org> # v3.10+ Signed-off-by: Hong H. Pham <hong.pham@windriver.com> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/powernv: Get FSP memory errors and plumb into memory poison infrastructure.
Get the memory errors reported by opal and plumb it into memory poison
infrastructure. This patch uses new messaging channel infrastructure to
pull the fsp memory errors to linux.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/mm: Only check for _PAGE_PRESENT in set_pte/pmd functions
We want to make sure we don't use these function when updating a pte
or pmd entry that have a valid hpte entry, because these functions
don't invalidate them. So limit the check to _PAGE_PRESENT bit.
Numafault core changes use these functions for updating _PAGE_NUMA bits.
That should be ok because when _PAGE_NUMA is set we can be sure that
hpte entries are not present.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/mm: Free up _PAGE_COHERENCE for numa fault use later
Set memory coherence always on hash64 config. If
a platform cannot have memory coherence always set they
can infer that from _PAGE_NO_CACHE and _PAGE_WRITETHRU
like in lpar. So we dont' really need a separate bit
for tracking _PAGE_COHERENCE.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- we allocate 128 bytes per cpu; so 256k with NR_CPUS=2048. As we have
constant initialisers, it's allocated in .text, causing a larger vmlinux
image. We may also allocate unecessary slb_shadow buffers (> no. pacas),
since we use the build-time NR_CPUS rather than the run-time nr_cpu_ids.
We could move this to the bss, but then we still have the NR_CPUS vs
nr_cpu_ids potential for overallocation.
This change dynamically allocates the slb_shadow array, during
initialise_pacas(). At a cost of 104 bytes of text, we save 256k of
data:
change_prot_numa should work even if _PAGE_NUMA != _PAGE_PROTNONE.
On archs like ppc64 that don't use _PAGE_PROTNONE and also have
a separate page table outside linux pagetable, we just need to
make sure that when calling change_prot_numa we flush the
hardware page table entry so that next page access result in a numa
fault.
We still need to make sure we use the numa faulting logic only
when CONFIG_NUMA_BALANCING is set. This implies the migrate-on-fault
(Lazy migration) via mbind will only work if CONFIG_NUMA_BALANCING
is set.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gerhard Sittig [Tue, 3 Dec 2013 10:56:52 +0000 (11:56 +0100)]
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node
the 'soc' node in the common .dtsi for MPC5121 has an '#interrupt-cells'
property although this node is not an interrupt controller
remove this erroneously placed property because starting with v3.13-rc1
lookup and resolution of 'interrupts' specs for peripherals gets misled,
emits 'no irq domain found' WARN() messages and breaks the boot process
...
irq: no irq domain found for /soc@80000000 !
fsl-diu-fb 80002100.display: could not get DIU IRQ
fsl-diu-fb: probe of 80002100.display failed with error -22
irq: no irq domain found for /soc@80000000 !
mpc512x_dma 80014000.dma: Error mapping IRQ!
mpc512x_dma: probe of 80014000.dma failed with error -22
...
irq: no irq domain found for /soc@80000000 !
fs_enet: probe of 80002800.ethernet failed with error -22
...
irq: no irq domain found for /soc@80000000 !
mpc5121-rtc 80000a00.rtc: mpc5121_rtc_probe: could not request irq: 0
mpc5121-rtc: probe of 80000a00.rtc failed with error -22
...
Brian King [Mon, 25 Nov 2013 22:27:54 +0000 (16:27 -0600)]
powerpc: Increase EEH recovery timeout for SR-IOV
In order to support concurrent adapter firmware download
to SR-IOV adapters on pSeries, each VF will see an EEH event
where the slot will remain in the unavailable state for
the duration of the adapter firmware update, which can take
as long as 5 minutes. Extend the EEH recovery timeout to
account for this.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 22 Nov 2013 08:28:46 +0000 (16:28 +0800)]
powerpc/eeh: Output PHB diag-data
When hitting frozen PE or fenced PHB, it's always indicative to
have dumped PHB diag-data for further analysis and diagnosis.
However, we never dump that for the cases. The patch intends to
dump PHB diag-data at the backend of eeh_ops::get_log() for PowerNV
platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 22 Nov 2013 08:28:45 +0000 (16:28 +0800)]
powerpc/powernv: Move PHB-diag dump functions around
Prior to the completion of PCI enumeration, we actively detects
EEH errors on PCI config cycles and dump PHB diag-data if necessary.
The EEH backend also dumps PHB diag-data in case of frozen PE or
fenced PHB. However, we are using different functions to dump the
PHB diag-data for those 2 cases.
The patch merges the functions for dumping PHB diag-data to one so
that we can avoid duplicate code. Also, we never dump PHB3 diag-data
during PCI config cycles with frozen PE. The patch fixes it as well.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>