Ezequiel Garcia [Sun, 13 Oct 2013 21:05:23 +0000 (18:05 -0300)]
mtd: Move major number definitions to major.h
This patch moves the char and block major number definitions
to major.h to be with the rest of the major numbers.
While doing this, include major.h in the files that need it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.
However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.
This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Brian Norris [Wed, 28 Aug 2013 01:45:10 +0000 (18:45 -0700)]
mtd: nand: hack ONFI for non-power-of-2 dimensions
Some bright specification writers decided to write this in the ONFI spec
(from ONFI 3.0, Section 3.1):
"The number of blocks and number of pages per block is not required to
be a power of two. In the case where one of these values is not a
power of two, the corresponding address shall be rounded to an
integral number of bits such that it addresses a range up to the
subsequent power of two value. The host shall not access upper
addresses in a range that is shown as not supported."
This breaks every assumption MTD makes about NAND block/chip-size
dimensions -- they *must* be a power of two!
And of course, an enterprising manufacturer has made use of this lovely
freedom. Exhibit A: Micron MT29F32G08CBADAWP
"- Plane size: 2 planes x 1064 blocks per plane
- Device size: 32Gb: 2128 blockss [sic]"
This quickly hits a BUG() in nand_base.c, since the extra dimensions
overflow so we think it's a second chip (on my single-chip setup):
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x44 (Micron MT29F32G08CBADAWP), 4256MiB, page size: 8192, OOB size: 744
------------[ cut here ]------------
kernel BUG at drivers/mtd/nand/nand_base.c:203!
Internal error: Oops - BUG: 0 [#1] SMP ARM
[... trim ...]
[<c02cf3e4>] (nand_select_chip+0x18/0x2c) from [<c02d25c0>] (nand_do_read_ops+0x90/0x424)
[<c02d25c0>] (nand_do_read_ops+0x90/0x424) from [<c02d2dd8>] (nand_read+0x54/0x78)
[<c02d2dd8>] (nand_read+0x54/0x78) from [<c02ad2c8>] (mtd_read+0x84/0xbc)
[<c02ad2c8>] (mtd_read+0x84/0xbc) from [<c02d4b28>] (scan_read.clone.4+0x4c/0x64)
[<c02d4b28>] (scan_read.clone.4+0x4c/0x64) from [<c02d4c88>] (search_bbt+0x148/0x290)
[<c02d4c88>] (search_bbt+0x148/0x290) from [<c02d4ea4>] (nand_scan_bbt+0xd4/0x5c0)
[... trim ...]
---[ end trace 0c9363860d865ff2 ]---
So to fix this, just truncate these dimensions down to the greatest
power-of-2 dimension that is less than or equal to the specified
dimension.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: <stable@vger.kernel.org>
Ezequiel Garcia [Fri, 4 Oct 2013 18:30:38 +0000 (15:30 -0300)]
mtd: nand: pxa3xx: Allocate data buffer on detected flash size
This commit replaces the currently hardcoded buffer size, by a
dynamic detection scheme. First a small 256 bytes buffer is allocated
so the device can be detected (using READID and friends commands).
After detection, this buffer is released and a new buffer is allocated
to acommodate the page size plus out-of-band size.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Priyanka Jain [Tue, 15 Oct 2013 05:39:05 +0000 (11:09 +0530)]
mtd: m25p80: Add support for Micron N25Q512A memory
Micron N25Q512A is a spi flash memory with following features:
-64MB size, 1.8V, Mulitple I/O, 4KB Sector erase memory.
-Memory is organised as 1024(64KB) main sectors.
-Each sector is divided into 256 pages.
-Register set/Opcodes are similar to other N25Q family products.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Mike Dunn [Thu, 10 Oct 2013 17:25:27 +0000 (10:25 -0700)]
mtd: docg4: fix status polling loop
The loop that polls the status register waiting for an operation to complete
foolishly bases the timeout simply on the number of loop iterations that have
ocurred. When I increased the processor clock speed, timeouts started to appear
for long block erasure operations. This patch measures the timeout using
jiffies.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jingoo Han [Mon, 23 Sep 2013 01:32:27 +0000 (10:32 +0900)]
mtd: denali: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jingoo Han [Mon, 23 Sep 2013 01:30:52 +0000 (10:30 +0900)]
mtd: pci: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
phram was 32-bit limited by design. Machines are growing up, but phram
module is still useful. Update it. The patch is bigger than minimum,
because simple_strtoul() is obsolete.
Tested on MIPS64 and compile-tested for PPC (32 bit).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com> Reviewed-by: Joern Engel <joern@logfs.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jingoo Han [Mon, 9 Sep 2013 05:42:52 +0000 (14:42 +0900)]
mtd: plat-ram: Remove casting the return value which is a void pointer
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current code sets the mtd->type with MTD_NANDFLASH for both
SLC and MLC. So the jffs2 may supports the MLC nand, but in actually,
the jffs2 should not support the MLC.
This patch uses the nand_is_slc() to check the nand cell type,
and set the mtd->type with the right nand type.
After this patch, the jffs2 only supports the SLC nand.
The side-effect of this patch:
Before this patch, the ioctl(MEMGETINFO) can only return with the
MTD_NANDFLASH; but after this patch, the ioctl(MEMGETINFO) will
return with the MTD_NANDFLASH for SLC, and MTD_MLCNANDFLASH for MLC.
So the user applictions(such as mtd-utils) should also changes a little
for this.
Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This helper detects that whether the mtd's type is nand type.
Now, it's clear that the MTD_NANDFLASH stands for SLC nand only.
So use the mtd_type_is_nand() to replace the old check method
to do the nand type (include the SLC and MLC) check.
Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd: nand: add more comment for MTD_NANDFLASH/MTD_MLCNANDFLASH
In current code, the MTD_NANDFLASH is used to represent both the SLC and
MLC. It is confusing to us.
By adding an explicit comment about these two macros, this patch makes it
clear that:
MTD_NANDFLASH : stands for SLC NAND,
MTD_MLCNANDFLASH : stands for MLC NAND (including TLC).
Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If the ONFI extended parameter page gives codeword_size == 0, the
extended ECC information is corrupt and should not be used. Currently,
we (correctly) avoid using the information, but we don't report the
error to the caller, so the caller doesn't know that we didn't
initialize ecc_strength_ds and ecc_step_ds. Now the caller can warn the
user that it does not have sufficient information.
This also removes the false and useless "ONFI extended param page
detected" debug message (it was printed even on the aforementioned
corruption, and for the success case, we don't really want a print).
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <b32955@freescale.com>
mtd: atmel_nand: use minimum ecc requirements of nand: ecc_{strength,step}_ds
Since ecc_{strength,step}_ds is introduced in nand_chip structure for
minimum ecc requirements. So we can use them directly and remove our
own get_onfi_ecc_param function.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd: atmel_nand: remove #if defined(CONFIG_OF) around OF-specific code
Since the of specific code are declared in <linux/of_mtd.h> regardless
of CONFIG_OF. Remove the #if defined(CONFIG_OF) guard and use an
IS_ENABLED(CONFIG_OF) instead.
Brian Norris [Tue, 13 Aug 2013 17:51:55 +0000 (10:51 -0700)]
mtd: nand: cleanup ONFI printed errors, warnings
The ONFI detection routine is too verbose in some cases and not verbose
enough in others. This patch refactors it to print only when there are
significant warnings/errors.
Probing in 16-bit mode:
It is unnecessary to print until after the READID (address 20h)
command. READID *has* to work properly in whatever bus width
configuration we are in, or else no identification mode works. So we
can silence some useless warnings on systems which come up in 16-bit
mode and do not even respond with an O-N-F-I string.
Valid parameter page:
Nobody needs to see this. Do we inform the user every time other
hardware responds properly? Instead, add an error message if *no*
uncorrupted parameter pages are found.
ONFI ECC:
Most drivers don't yet use the reported minimum ECC values, so it
shouldn't yet be a fatal condition if the extended parameter page is
incorrect. But we should at least give a warning for the corner cases
that we don't expect.
ONFI flash detected:
Nobody needs to see this. This is the expected case, that we detect
ONFI properly, or else it wasn't ONFI-compliant and is detected by
some other routine.
Brian Norris [Wed, 28 Aug 2013 01:01:19 +0000 (18:01 -0700)]
mtd: onenand: remove unused variable assignments
These variable assignments are never used (the variables are either
never used or are overwritten before use). This resolves some compiler
warnings like the following:
drivers/mtd/onenand/onenand_base.c: In function 'flexonenand_get_boundary':
drivers/mtd/onenand/onenand_base.c:3532:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
drivers/mtd/onenand/onenand_base.c: In function 'onenand_probe':
drivers/mtd/onenand/onenand_base.c:3838:6: warning: variable 'maf_id' set but not used [-Wunused-but-set-variable]
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
Brian Norris [Sat, 10 Aug 2013 08:09:49 +0000 (01:09 -0700)]
mtd: nand: stop exporting nand_default_bbt
I removed the last non-nand_base users of this, and we shouldn't have
any more modules that need to access it. It's only non-static to share
between nand_base and nand_bbt.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver is doing some strange logic here. If it doesn't have
flash-based BBT enabled, it allows nand_scan_tail() to scan the BBT. But
if it is using flash-based BBT, it tells nand_scan_tail() to skip
scanning, then it immediately calls the default BBT scanning function
itself.
As I read it, this logic is equivalent to the default nand_scan_tail()
behavior without interfering with NAND_SKIP_BBTSCAN or calling
nand_default_bbt() directly at all.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Just like the rest of the subsystems, let's add the required no-op
functions to implement stubs when CONFIG_OF=n.
This prevents MTD drivers from having ugly ifdefs in their code,
and instead hide the ifdef monster in the header closet (far away
from people's sight).
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Linus Torvalds [Tue, 8 Oct 2013 16:23:12 +0000 (09:23 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Various fixlets:
On the kernel side:
- fix a race
- fix a bug in the handling of the perf ring-buffer data page
On the tooling side:
- fix the handling of certain corrupted perf.data files
- fix a bug in 'perf probe'
- fix a bug in 'perf record + perf sched'
- fix a bug in 'make install'
- fix a bug in libaudit feature-detection on certain distros"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf session: Fix infinite loop on invalid perf.data file
perf tools: Fix installation of libexec components
perf probe: Fix to find line information for probe list
perf tools: Fix libaudit test
perf stat: Set child_pid after perf_evlist__prepare_workload()
perf tools: Add default handler for mmap2 events
perf/x86: Clean up cap_user_time* setting
perf: Fix perf_pmu_migrate_context
powerpc/irq: Don't switch to irq stack from softirq stack
irq_exit() is now called on the irq stack, which can trigger a switch to
the softirq stack from the irq stack. If an interrupt happens at that
point, we will not properly detect the re-entrancy and clobber the
original return context on the irq stack.
This fixes it. The side effect is to prevent all nesting from softirq
stack to irq stack even in the "safe" case but it's simpler that way and
matches what x86_64 does.
Reported-by: Cédric Le Goater <clg@fr.ibm.com> Tested-by: Cédric Le Goater <clg@fr.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 7 Oct 2013 16:30:36 +0000 (09:30 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for hidraw reference counting regression, by Manoj Chourasia
- fix for minor number allocation for uhid, by David Herrmann
- other small unsorted fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: fix FF deadlock
HID: add Holtek USB ID 04d9:a081 SHARKOON DarkGlider
HID: hidraw: close underlying device at removal of last reader
HID: roccat: Fix "cannot create duplicate filename" problems
HID: uhid: allocate static minor
Linus Torvalds [Mon, 7 Oct 2013 16:30:02 +0000 (09:30 -0700)]
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull Tile bugfixes from Chris Metcalf:
"This fixes some serious issues with PREEMPT support, and a couple of
smaller corner-case issues fixed in the last couple of weeks"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch: tile: re-use kbasename() helper
tile: use a more conservative __my_cpu_offset in CONFIG_PREEMPT
tile: ensure interrupts disabled for preempt_schedule_irq()
tile: change lock initalization in hardwall
tile: include: asm: use 'long long' instead of 'u64' for atomic64_t and its related functions
David Herrmann [Wed, 2 Oct 2013 11:47:28 +0000 (13:47 +0200)]
HID: wiimote: fix FF deadlock
The input core has an internal spinlock that is acquired during event
injection via input_event() and friends but also held during FF callbacks.
That means, there is no way to share a lock between event-injection and FF
handling. Unfortunately, this is what is required for wiimote state
tracking and what we do with state.lock and input->lock.
This deadlock can be triggered when using continuous data reporting and FF
on a wiimote device at the same time. I takes me at least 30m of
stress-testing to trigger it but users reported considerably shorter
times (http://bpaste.net/show/132504/) when using some gaming-console
emulators.
The real problem is that we have two copies of internal state, one in the
wiimote objects and the other in the input device. As the input-lock is
not supposed to be accessed from outside of input-core, we have no other
chance than offloading FF handling into a worker. This actually works
pretty nice and also allows to implictly merge fast rumble changes into a
single request.
Due to the 3-layered workers (rumble+queue+l2cap) this might reduce FF
responsiveness. Initial tests were fine so lets fix the race first and if
it turns out to be too slow we can always handle FF out-of-band and skip
the queue-worker.
Cc: <stable@vger.kernel.org> # 3.11+ Reported-by: Thomas Schneider Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Mon, 7 Oct 2013 08:13:26 +0000 (01:13 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bux fixes, notable are the regression with ptrace vs
restarting system calls and the patch for kdump to be able to copy
from virtual memory"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix system call restart after inferior call
s390: Allow vmalloc target buffers for copy_from_oldmem()
s390/sclp: properly detect line mode console
s390/kprobes: add exrl to list of prohibited opcodes
s390/3270: fix return value check in tty3270_resize_work()
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target fixes queued up for v3.12-rc4 code.
The highlights include:
- Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
- Allow sess_cmd_map allocation failure fallback to use vzalloc
- Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
- Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
zero scsi_status bug
- Make iscsi-target do acknowledgement tag release from RX context
- Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags
Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
legacy wait_for_task=true release during fast-past StatSN
acknowledgement, and two other SRP target related patches that address
long-standing issues that are CC'ed for v3.3+.
Extra thanks to Thomas Glanzmann for his testing feedback with
COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
iscsi-target: Perform release of acknowledged tags from RX context
iscsi-target: Only perform wait_for_tasks when performing shutdown
target: Fail on non zero scsi_status in compare_and_write_callback
target: Fix recursive COMPARE_AND_WRITE callback failure
target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
ib_srpt: always set response for task management
target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
ib_srpt: Destroy cm_id before destroying QP.
target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02
Linus Torvalds [Sun, 6 Oct 2013 20:35:15 +0000 (13:35 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the slave dmanegine fixes. We have the fix for deadlock issue
on imx-dma by Michael and Josh's edma config fix along with author
change"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: imx-dma: fix callback path in tasklet
dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
edma: Update author email address
Linus Torvalds [Sat, 5 Oct 2013 19:17:24 +0000 (12:17 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes, including a regression fix from
Liu Bo that solves rare crashes with compression on.
I've merged my for-linus up to 3.12-rc3 because the top commit is only
meant for 3.12. The rest of the fixes are also available in my master
branch on top of my last 3.11 based pull"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: Fix crash due to not allocating integrity data for a bioset
Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
Btrfs: eliminate races in worker stopping code
Btrfs: fix crash of compressed writes
Btrfs: fix transid verify errors when recovering log tree
Linus Torvalds [Sat, 5 Oct 2013 19:11:40 +0000 (12:11 -0700)]
Merge tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two patches for the OMAP driver, dealing with setting up IRQs properly
on the device tree boot path"
* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/omap: auto-setup a GPIO when used as an IRQ
gpio/omap: maintain GPIO and IRQ usage separately
Linus Torvalds [Sat, 5 Oct 2013 18:54:10 +0000 (11:54 -0700)]
Merge tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are none fixes for various USB driver problems. The majority are
gadget/musb fixes, but there are some new device ids in here as well"
* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: add Intel Clovertrail pci id
usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
usb: gadget: f_fs: fix error handling
usb: musb: dsps: do not bind to "musb-hdrc"
USB: serial: option: Ignore card reader interface on Huawei E1750
usb: musb: gadget: fix otg active status flag
usb: phy: gpio-vbus: fix deferred probe from __init
usb: gadget: pxa25x_udc: fix deferred probe from __init
usb: musb: fix otg default state
Linus Torvalds [Sat, 5 Oct 2013 18:26:19 +0000 (11:26 -0700)]
Merge tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty driver fixes for 3.12-rc4.
One fixes the reported regression in the n_tty code that a number of
people found recently, and the other one fixes an issue with xen
consoles that broke in 3.10"
* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
xen/hvc: allow xenboot console to be used again
tty: Fix pty master read() after slave closes
Darrick J. Wong [Fri, 20 Sep 2013 03:37:07 +0000 (20:37 -0700)]
btrfs: Fix crash due to not allocating integrity data for a bioset
When btrfs creates a bioset, we must also allocate the integrity data pool.
Otherwise btrfs will crash when it tries to submit a bio to a checksumming
disk:
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Linus Torvalds [Sat, 5 Oct 2013 03:50:16 +0000 (20:50 -0700)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Small set of cifs fixes. Most important is Jeff's fix that works
around disconnection problems which can be caused by simultaneous use
of user space tools (starting a long running smbclient backup then
doing a cifs kernel mount) or multiple cifs mounts through a NAT, and
Jim's fix to deal with reexport of cifs share.
I expect to send two more cifs fixes next week (being tested now) -
fixes to address an SMB2 unmount hang when server dies and a fix for
cifs symlink handling of Windows "NFS" symlinks"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] update cifs.ko version
[CIFS] Remove ext2 flags that have been moved to fs.h
[CIFS] Provide sane values for nlink
cifs: stop trying to use virtual circuits
CIFS: FS-Cache: Uncache unread pages in cifs_readpages() before freeing them
Linus Torvalds [Sat, 5 Oct 2013 03:48:20 +0000 (20:48 -0700)]
Merge tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"We merged what was intended to be an MMCONFIG cleanup, but in fact,
for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and it broke all config space for
other domains.
This reverts the change"
* tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"
07f9b61c was intended to be a cleanup that didn't change anything, but in
fact, for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and all config space for other domains.
Linus Torvalds [Fri, 4 Oct 2013 22:03:42 +0000 (15:03 -0700)]
Merge tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- The resume part of user space driven hibernation (s2disk) is now
broken after the change that moved the creation of memory bitmaps to
after the freezing of tasks, because I forgot that the resume utility
loaded the image before freezing tasks and needed the bitmaps for
that. The fix adds special handling for that case.
- One of recent commits changed the export of acpi_bus_get_device() to
EXPORT_SYMBOL_GPL(), which was technically correct but broke existing
binary modules using that function including one in particularly
widespread use. Change it back to EXPORT_SYMBOL().
- The intel_pstate driver sometimes fails to disable turbo if its
no_turbo sysfs attribute is set. Fix from Srinivas Pandruvada.
- One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
which still (incorrectly) treats non-NULL as non-error. Fix from
Philipp Zabel.
- The SPEAr cpufreq driver uses a wrong variable type in one place
preventing it from catching errors returned by one of the functions
called by it. Fix from Sachin Kamat.
* tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
Linus Torvalds [Fri, 4 Oct 2013 21:47:22 +0000 (14:47 -0700)]
Merge tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
"There are lockdep annotations for project quotas, a fix for dirent
dtype support on v4 filesystems, a fix for a memory leak in recovery,
and a fix for the build error that resulted from it. D'oh"
* tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: Use kmem_free() instead of free()
xfs: fix memory leak in xlog_recover_add_to_trans
xfs: dirent dtype presence is dependent on directory magic numbers
xfs: lockdep needs to know about 3 dquot-deep nesting
Ilya Dryomov [Wed, 2 Oct 2013 17:41:01 +0000 (20:41 +0300)]
Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
free_device rcu callback, scheduled from btrfs_rm_dev_replace_srcdev,
can be processed before btrfs_scratch_superblock is called, which would
result in a use-after-free on btrfs_device contents. Fix this by
zeroing the superblock before the rcu callback is registered.
Cc: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Ilya Dryomov [Wed, 2 Oct 2013 16:39:50 +0000 (19:39 +0300)]
Btrfs: eliminate races in worker stopping code
The current implementation of worker threads in Btrfs has races in
worker stopping code, which cause all kinds of panics and lockups when
running btrfs/011 xfstest in a loop. The problem is that
btrfs_stop_workers is unsynchronized with respect to check_idle_worker,
check_busy_worker and __btrfs_start_workers.
E.g., check_idle_worker race flow:
btrfs_stop_workers(): check_idle_worker(aworker):
- grabs the lock
- splices the idle list into the
working list
- removes the first worker from the
working list
- releases the lock to wait for
its kthread's completion
- grabs the lock
- if aworker is on the working list,
moves aworker from the working list
to the idle list
- releases the lock
- grabs the lock
- puts the worker
- removes the second worker from the
working list
......
btrfs_stop_workers returns, aworker is on the idle list
FS is umounted, memory is freed
......
aworker is waken up, fireworks ensue
With this applied, I wasn't able to trigger the problem in 48 hours,
whereas previously I could reliably reproduce at least one of these
races within an hour.
Reported-by: David Sterba <dsterba@suse.cz> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Liu Bo [Tue, 1 Oct 2013 15:49:49 +0000 (23:49 +0800)]
Btrfs: fix crash of compressed writes
The crash[1] is found by xfstests/generic/208 with "-o compress",
it's not reproduced everytime, but it does panic.
The bug is quite interesting, it's actually introduced by a recent commit
(573aecafca1cf7a974231b759197a1aebcf39c2a,
Btrfs: actually limit the size of delalloc range).
Btrfs implements delay allocation, so during writeback, we
(1) get a page A and lock it
(2) search the state tree for delalloc bytes and lock all pages within the range
(3) process the delalloc range, including find disk space and create
ordered extent and so on.
(4) submit the page A.
It runs well in normal cases, but if we're in a racy case, eg.
buffered compressed writes and aio-dio writes,
sometimes we may fail to lock all pages in the 'delalloc' range,
in which case, we need to fall back to search the state tree again with
a smaller range limit(max_bytes = PAGE_CACHE_SIZE - offset).
The mentioned commit has a side effect, that is, in the fallback case,
we can find delalloc bytes before the index of the page we already have locked,
so we're in the case of (delalloc_end <= *start) and return with (found > 0).
This ends with not locking delalloc pages but making ->writepage still
process them, and the crash happens.
This fixes it by just thinking that we find nothing and returning to caller
as the caller knows how to deal with it properly.
Josef Bacik [Mon, 30 Sep 2013 18:10:43 +0000 (14:10 -0400)]
Btrfs: fix transid verify errors when recovering log tree
If we crash with a log, remount and recover that log, and then crash before we
can commit another transaction we will get transid verify errors on the next
mount. This is because we were not zero'ing out the log when we committed the
transaction after recovery. This is ok as long as we commit another transaction
at some point in the future, but if you abort or something else goes wrong you
can end up in this weird state because the recovery stuff says that the tree log
should have a generation+1 of the super generation, which won't be the case of
the transaction that was started for recovery. Fix this by removing the check
and _always_ zero out the log portion of the super when we commit a transaction.
This fixes the transid verify issues I was seeing with my force errors tests.
Thanks,
Linus Torvalds [Fri, 4 Oct 2013 19:54:11 +0000 (12:54 -0700)]
selinux: remove 'flags' parameter from inode_has_perm
Every single user passes in '0'. I think we had non-zero users back in
some stone age when selinux_inode_permission() was implemented in terms
of inode_has_perm(), but that complicated case got split up into a
totally separate code-path so that we could optimize the much simpler
special cases.
See commit 2e33405785d3 ("SELinux: delay initialization of audit data in
selinux_inode_permission") for example.
Free the memory in error path of xlog_recover_add_to_trans().
Normally this memory is freed in recovery pass2, but is leaked
in the error path.
Signed-off-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 519ccb81ac1c8e3e4eed294acf93be00b43dcad6)
Dave Chinner [Sun, 29 Sep 2013 23:37:04 +0000 (09:37 +1000)]
xfs: dirent dtype presence is dependent on directory magic numbers
The determination of whether a directory entry contains a dtype
field originally was dependent on the filesystem having CRCs
enabled. This meant that the format for dtype beign enabled could be
determined by checking the directory block magic number rather than
doing a feature bit check. This was useful in that it meant that we
didn't need to pass a struct xfs_mount around to functions that
were already supplied with a directory block header.
Unfortunately, the introduction of dtype fields into the v4
structure via a feature bit meant this "use the directory block
magic number" method of discriminating the dirent entry sizes is
broken. Hence we need to convert the places that use magic number
checks to use feature bit checks so that they work correctly and not
by chance.
The current code works on v4 filesystems only because the dirent
size roundup covers the extra byte needed by the dtype field in the
places where this problem occurs.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 367993e7c6428cb7617ab7653d61dca54e2fdede)
The lockdep annotation for dquot lock nesting only understands
locking for user and "other" dquots, not user, group and quota
dquots. Fix the annotations to match the locking heirarchy we now
have.
Reported-by: Michael L. Semon <mlsemon35@gmail.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit f112a049712a5c07de25d511c3c6587a2b1a015e)
Namhyung Kim [Mon, 30 Sep 2013 08:19:48 +0000 (17:19 +0900)]
perf session: Fix infinite loop on invalid perf.data file
perf-record updates the header in the perf.data file at termination.
Without this update perf-report (and other processing built-ins) it
caused an infinite loop when perf report (or something like) called.
This is because the algorithm in __perf_session__process_events()
depends on the data_size which is read from file header. Use file size
directly instead in this case to do the best-effort processing.
Signed-off-by: Namhyung Kim <namhyung@kernel.org> Tested-by: David Ahern <dsahern@gmail.com> Tested-by: Sonny Rao <sonnyrao@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Cc: David Ahern <dsahern@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Sonny Rao <sonnyrao@chromium.org> Link: http://lkml.kernel.org/r/1380529188-27193-1-git-send-email-namhyung@kernel.org Signed-off-by: David Ahern <dsahern@gmail.com>
[ Reworded warning as per Ingo Molnar suggestion, replaces 'perf.data'
with session->filename, to precisely identify the data file involved ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf tools: Fix installation of libexec components
Doing a fresh install on a user home directory needs to first make sure
that the ~/libexec/perf-core/ directory is present so that
'perf-archive' like scripts, 'perf test' attr config files and 'perf
script' scripts can be installed.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-z7ryi3r1b9dn9smbfnab0fdc@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf probe: Fix to find line information for probe list
Fix to find the correct (as much as possible) line information for
listing probes. Without this fix, perf probe --list action will show
incorrect line information as below;
probe:getname_flags (on getname_flags@ksrc/linux-3/fs/namei.c)
probe:getname_flags_1 (on getname:-89@x86/include/asm/current.h)
probe:getname_flags_2 (on user_path_at_empty:-2054@x86/include/asm/current.h)
The minus line number is obviously wrong, and current.h is not related
to the probe point. Deeper investigation discovered that there were 2
issues related to this bug, and minor typos too.
The 1st issue is the rack of considering about nested inlined functions,
which causes the wrong (relative) line number.
The 2nd issue is that the dwarf line info is not correct at those
points. It points 14th line of current.h.
Since it seems that the line info includes somewhat unreliable
information, this fixes perf to try to find correct line information
from both of debuginfo and line info as below.
1) Probe address is the entry of a function instance
In this case, the line is set as the function declared line.
2) Probe address is the entry of an expanded inline function block
In this case, the line is set as the function call-site line.
This means that the line number is relative from the entry line
of caller function (which can be an inlined function if nested)
3) Probe address is inside a function instance or an expanded
inline function block
In this case, perf probe queries the line number from lineinfo
and verify the function declared file is same as the file name
queried from lineinfo.
If the file name is different, it is a failure case. The probe
address is shown as symbol+offset.
4) Probe address is not in the any function instance
This is a failure case, the probe address is shown as
symbol+offset.
With this fix, perf probe -l shows correct probe lines as below;
probe:getname_flags (on getname_flags@ksrc/linux-3/fs/namei.c)
probe:getname_flags_1 (on getname:2@ksrc/linux-3/fs/namei.c)
probe:getname_flags_2 (on user_path_at_empty:4@ksrc/linux-3/fs/namei.c)
Changes at v2:
- Fix typos in the function comments. (Thanks to Namhyung Kim)
- Use die_find_top_inlinefunc instead of die_find_inlinefunc_next.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20130930092144.1693.11058.stgit@udc4-manage.rcp.hitachi.co.jp Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
projects / karo-tx-linux.git / log