Jyri Sarha [Wed, 27 May 2015 08:58:37 +0000 (11:58 +0300)]
drm/tilcdc: Initialize crtc->port
Initialize port device node pointer in the tilcdc crtc. Fixes "Falling
back to first CRTC" warning from tda998x driver.
The tda998x encoder driver calls drm_of_find_possible_crtcs() to
initialize possible_crtcs of struct drm_encoder. The crtc->port needs
to be initialized for drm_of_find_possible_crtcs() to work.
Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Jyri Sarha [Fri, 8 Jan 2016 12:33:09 +0000 (14:33 +0200)]
drm/tilcdc: Disable sync lost interrupt if it fires on every frame
Disable the sync lost interrupt if it fires on every frame for 50
consecutive frames in a row. This is relatively sure sign of the sync
lost interrupt being stuck and firing on every frame even if the
display otherwise appears to work OK.
Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Jyri Sarha [Wed, 9 Dec 2015 10:16:11 +0000 (12:16 +0200)]
drm/tilcdc: Fix interrupt enable/disable code for version 2 tilcdc
Fix interrupt enable/disable code for version 2 tilcdc. In version 2
tilcdc there is a separate register for disabling interrupts. Writing
0 to enable registers bits does not have any effect. The interrupt
clear register works the same way, writing 1 to specific bit disables
the interrupt and writing 0 does not have any effect.
The "bug" that is fixed here does not really do any harm since the
interrupts are enabled only once in the power up and disabled before
power down.
Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Tue, 3 Nov 2015 10:00:51 +0000 (12:00 +0200)]
drm/tilcdc: Do not update the next frame buffer close to vertical blank
Do not update the next frame buffer close to vertical blank. This is
to avoid situation when the frame changes between writing of
LCDC_DMA_FB_BASE_ADDR_0_REG and LCDC_DMA_FB_CEILING_ADDR_0_REG.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch] Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tomi Valkeinen [Tue, 20 Oct 2015 06:37:27 +0000 (09:37 +0300)]
drm/tilcdc: Get rid of complex ping-pong mechanism
Get rid of complex ping-pong mechanism and replace it with simpler
single buffer flipping code.
The LCDC HW appears to be designed mainly static framebuffers in
mind. There are two modes of operation, either static single buffer,
or ping pong double buffering with two static buffers switching back
and forth. Luckily the framebuffer start address is fetched only in
the beginning of the frame and changing the address after that only
takes effect after the next vertical blank. The page flipping code can
simply write the address of the new framebuffer and the page is
flipped automatically after the next vertical blank. Using the ping
pong double buffering makes the flipping code way more complex and it
does not provide any benefit, so it is better to switch to single
buffer operation.
There is still one problem in updating the framebuffer dma address on
the fly. There are two registers defining the framebuffer dma area and
things may break if the dma address is fetched in while the registers
are are being updated.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch] Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tomi Valkeinen [Tue, 20 Oct 2015 09:04:05 +0000 (12:04 +0300)]
drm/tilcdc: remove broken error handling
Remove broken error handling. The condition for handling the
LCDC_SYNC_LOST and LCDC_FIFO_UNDERFLOW could never be satisfied as the
LCDC_SYNC_LOST interrupt is not enabled. Also the requirement to have
both LCDC_SYNC_LOST and LCDC_FIFO_UNDERFLOW fired at once before
handling the error looks weird.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch] Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tomi Valkeinen [Tue, 20 Oct 2015 06:37:27 +0000 (09:37 +0300)]
drm/tilcdc: split reset to a separate function
Split reset to a separate function and use usleep_range(250, 1000)
instead of msleep(1) to to keep the reset bit on long enough.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch, changed mdelay(500) to usleep_range(250, 1000)] Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tomi Valkeinen [Mon, 19 Oct 2015 09:30:03 +0000 (12:30 +0300)]
drm/tilcdc: cleanup runtime PM handling
Cleanup runtime PM handling. Before the patch the usage of pm_runtime
calls was inconsistent and hard to follow. After the update the
pm_runtime calls are removed from set_scanout() and called around
major operations that access the HW. After the patch the DPMS code does
not have pm_runtime_forbid/allow calls any more and
pm_runtime_irq_safe() is not set anymore.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch] Signed-off-by: Jyri Sarha <jsarha@ti.com>
drm/tilcdc: Allocate register storage based on the actual number registers
Allocate suspend/resume register storage based on the actual number
registers the driver is aware of. The static allocation for register
storage had fallen behind badly.
Reported-by: Michael Bode <michael@bumbleB.de> Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix build error when !CONFIG_CPU_FREQ
drivers/gpu/drm/tilcdc/tilcdc_drv.c: In function 'tilcdc_load':
drivers/gpu/drm/tilcdc/tilcdc_drv.c:327:1: error: label 'fail_put_clk' defined but not used [-Werror=unused-label]
fail_put_clk:
^
Darren Etheridge [Thu, 25 Sep 2014 00:59:32 +0000 (00:59 +0000)]
drm/tilcdc: disable the lcd controller/dma engine when suspend invoked
The LCD controller must be deactivated and all DMA transactions stopped
when the suspend power state is entered otherwise the PRCM causes the L3
bus to get stuck in transition state.
This commit forces the lcdc to be shut down and waits for all pending DMA
transactions to complete as part of the suspend handler for this driver.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Tested-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Darren Etheridge [Thu, 25 Sep 2014 00:59:31 +0000 (00:59 +0000)]
drm/tilcdc: make frame_done interrupt active at all times
The frame_done interrupt was only being enabled when the vsync
interrupts were being enabled by DRM. However the frame_done is
used to determine if the LCD controller has successfully completed
the raster_enable, raster_disable commands and the vsync interrupts
are not always enabled during these operations.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Tested-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Darren Etheridge [Fri, 19 Sep 2014 01:42:57 +0000 (01:42 +0000)]
drm/tilcdc: fix kernel panic on suspend when no hdmi monitor connected
On BeagleBone Black if no HDMI monitor is connected and suspend
is requested a kernel panic will result:
root@am335x-evm:~# echo mem > /sys/power/state
[ 65.548710] PM: Syncing filesystems ... done.
[ 65.631311] Freezing user space processes ... (elapsed 0.006 seconds) done.
[ 65.648619] Freezing remaining freezable tasks ... (elapsed 0.005 seconds) done.
[ 65.833500] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa30e004
[ 65.841692] Internal error: : 1028 [#1] SMP ARM
<snip>
[ 66.105287] [<c03765f0>] (platform_pm_suspend) from [<c037b6d4>] (dpm_run_callback+0x34/0x70)
[ 66.114370] [<c037b6d4>] (dpm_run_callback) from [<c037ba84>] (__device_suspend+0x10c/0x2f4)
[ 66.123357] [<c037ba84>] (__device_suspend) from [<c037d004>] (dpm_suspend+0x58/0x218)
[ 66.131796] [<c037d004>] (dpm_suspend) from [<c008d948>] (suspend_devices_and_enter+0x9c/0x3c0)
[ 66.141055] [<c008d948>] (suspend_devices_and_enter) from [<c008de7c>] (pm_suspend+0x210/0x24c)
[ 66.150312] [<c008de7c>] (pm_suspend) from [<c008cabc>] (state_store+0x68/0xb8)
[ 66.158103] [<c008cabc>] (state_store) from [<c02e9654>] (kobj_attr_store+0x14/0x20)
[ 66.166355] [<c02e9654>] (kobj_attr_store) from [<c0185c70>] (sysfs_kf_write+0x4c/0x50)
[ 66.174883] [<c0185c70>] (sysfs_kf_write) from [<c018926c>] (kernfs_fop_write+0xb4/0x150)
[ 66.183598] [<c018926c>] (kernfs_fop_write) from [<c0122638>] (vfs_write+0xa8/0x180)
[ 66.191846] [<c0122638>] (vfs_write) from [<c01229f8>] (SyS_write+0x40/0x8c)
[ 66.199365] [<c01229f8>] (SyS_write) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 66.207426] Code: e595c210e5932000e59cc000e08c2002 (e592c000)
This is because the lcdc module is not enabled when no monitor is detected
to save power. However the suspend handler just blindly tries to save the
lcdc state by copying out the pertinent registers. However module is off
so no good things happen when you try and access it.
This patch only saves off the registers if the module is enabled, and
then only restores the registers on resume if they were saved off during
suspend.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Tested-by: Dave Gerlach <d-gerlach@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dave Gerlach [Tue, 29 Jul 2014 06:27:58 +0000 (06:27 +0000)]
drm/tilcdc: adopt pinctrl support
Update tilcdc driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Darren Etheridge <detheridge@ti.com> Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 7 Feb 2014 17:37:07 +0000 (17:37 +0000)]
drm/tilcdc: verify fb pitch
LCDC hardware does not support fb pitch that is different (i.e. larger)
than the screen size. The driver currently does no checks for this, and
the results of too big pitch are are flickering and lower fps.
This issue easily happens when using libdrm's modetest tool with non-32
bpp modes. As modetest always allocated 4 bytes per pixel, it implies a
bigger pitch for 16 or 24 bpp modes.
This patch adds a check to reject pitches the hardware cannot support.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Darren Etheridge <detheridge@ti.com> Signed-off-by: Jyri Sarha <jsarha@ti.com>
Darren Etheridge [Wed, 15 Jan 2014 21:52:36 +0000 (15:52 -0600)]
drm/tilcdc: rewrite pixel clock calculation
Updating the tilcdc DRM driver code to calculate the LCD controller
pixel clock more accurately. Based on a suggested implementation by
Tomi Valkeinen.
The current code does not work correctly and produces wrong results
with many requested clock rates. It also oddly uses two different
clocks, a display pll clock and a divider clock (child of display
pll), instead of just using the clock coming to the lcdc.
This patch removes the use of the display pll clock, and rewrites the
code to calculate the clock rates. The idea is simply to request a
clock rate of pixelclock*2, as the LCD controller has an internal
divider which we set to 2.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
[Rewrapped description] Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dave Airlie [Thu, 25 Feb 2016 00:30:59 +0000 (10:30 +1000)]
Merge branch 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev into drm-next
rcar-du updates.
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev: (281 commits)
drm: rcar-du: Add tri-planar memory formats support
drm: rcar-du: Add probe deferral debug messages
drm: rcar-du: lvds: Add R-Car Gen3 support
drm: rcar-du: lvds: Rename PLLEN bit to PLLON
drm: rcar-du: lvds: Fix PLL frequency-related configuration
drm: rcar-du: lvds: Avoid duplication of clock clamp code
drm: rcar-du: Add R8A7795 device support
drm: rcar-du: Output the DISP signal on the ODDF pin
drm: rcar-du: Output the DISP signal on the DISP pin
drm: rcar-du: Support up to 4 CRTCs
drm: rcar-du: Drop LVDS double dependency on OF
drm: rcar-du: Enable compilation on ARM64
drm: rcar-du: Fix compile warning on 64-bit platforms
drm: rcar-du: Expose the VSP1 compositor through KMS planes
drm: rcar-du: Move plane allocator to rcar_du_plane.c
drm: rcar-du: Restart the DU group when a plane source changes
drm: rcar-du: Add VSP1 compositor support
drm: rcar-du: Add VSP1 support to the planes allocator
drm: rcar-du: Refactor plane setup
drm: rcar-du: Compute plane DDCR4 register value directly
...
drm: rcar-du: Output the DISP signal on the ODDF pin
The ODDF signal, output by default on the ODDF pin, isn't used on any
board supported in the kernel. As the Gen3 Salvator-X board uses the
ODDF pin as a DISP signal, hardcode that configuration in the driver.
Use of the ODDF signal will be implemented later through proper DT-based
configuration of the DU pins.
drm: rcar-du: Output the DISP signal on the DISP pin
The DE signal is currently configured to be identical to the DISP
signal and is used for the same purpose. To make it clearer that the
DISP pin outputs the DISP signal, select it explicitly.
drm: rcar-du: Expose the VSP1 compositor through KMS planes
On R-Car Gen3 SoCs the DU lost its ability to access memory directly and
needs to work in conjunction with the VSP to do so. This commit handles
the VSP internally to hide it from the user.
Laurent Pinchart [Sat, 24 Aug 2013 00:17:03 +0000 (02:17 +0200)]
drm: rcar-du: Restart the DU group when a plane source changes
Plane sources are configured by the VSPS bit in the PnDDCR4 register.
Although the datasheet states that the bit is updated during vertical
blanking, it seems that updates only occur when the DU group is held in
reset through the DSYSR.DRES bit. Restart the group if the source
changes.
Laurent Pinchart [Fri, 21 Jun 2013 15:36:15 +0000 (17:36 +0200)]
drm: rcar-du: Add VSP1 support to the planes allocator
The R8A7790 DU can source frames directly from the VSP1 devices VSPD0
and VSPD1. VSPD0 feeds DU0/1 plane 0, and VSPD1 feeds either DU2 plane 0
or DU0/1 plane 1.
Allocate the correct fixed plane when sourcing frames from VSPD0 or
VSPD1, and allocate planes in reverse index order otherwise to ensure
maximum availability of planes 0 and 1.
Rename plane setup functions using more explicit names, and use local
variables to store intermediate values to increase readability. This
also prepares for VSP compositor support.
drm: rcar-du: Don't update planes on disabled CRTCs
A disabled CRTC can't display planes, the driver shouldn't try to
configure it when updating planes. The DRM core will store the plane
state for us, and the plane will be configured appropriately the next
time the CRTC is enabled.
Laurent Pinchart [Sun, 24 Jan 2016 22:28:11 +0000 (00:28 +0200)]
drm: rcar-du: Remove local CRTC enabled state
The atomic framework guarantees that the CRTC enable and disable
functions will only be called when needed, there's no need to duplicate
the CRTC state check. By replacing the local CRTC enabled state check at
resume time with the CRTC active state we can remove the local CRTC
enabled state altogether.
drm: rcar-du: Perform initialization/cleanup at probe/remove time
The drm driver .load() operation is prone to race conditions as it
initializes the driver after registering the device nodes. Its usage is
deprecated, inline it in the probe function and call drm_dev_alloc() and
drm_dev_register() explicitly.
For consistency inline the .unload() handler in the remove function as
well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/media/platform/vsp1/vsp1_drm.c:47:5: warning: no previous prototype for 'vsp1_du_init' [-Wmissing-prototypes]
int vsp1_du_init(struct device *dev)
^
drivers/media/platform/vsp1/vsp1_drm.c:76:5: warning: no previous prototype for 'vsp1_du_setup_lif' [-Wmissing-prototypes]
int vsp1_du_setup_lif(struct device *dev, unsigned int width,
^
drivers/media/platform/vsp1/vsp1_drm.c:221:6: warning: no previous prototype for 'vsp1_du_atomic_begin' [-Wmissing-prototypes]
void vsp1_du_atomic_begin(struct device *dev)
^
drivers/media/platform/vsp1/vsp1_drm.c:273:5: warning: no previous prototype for 'vsp1_du_atomic_update' [-Wmissing-prototypes]
int vsp1_du_atomic_update(struct device *dev, unsigned int rpf_index,
^
drivers/media/platform/vsp1/vsp1_drm.c:451:6: warning: no previous prototype for 'vsp1_du_atomic_flush' [-Wmissing-prototypes]
void vsp1_du_atomic_flush(struct device *dev)
^
[media] v4l: vsp1: Configure device based on IP version
The IP version number carries enough information to identify the exact
device instance features. Drop the related DT properties and use the IP
version instead.
Display lists contain lists of registers and associated values to be
applied atomically by the hardware. They lower the pressure on interrupt
processing delays when reprogramming the device as settings can be
prepared well in advance and queued to the hardware without waiting for
the end of the current frame.
Display list support is currently limited to the DRM pipeline.
[media] v4l: vsp1: Implement atomic update for the DRM driver
Add two API functions named vsp1_du_atomic_begin() and
vsp1_du_atomic_flush() to signal the start and end of an atomic update.
The vsp1_du_setup_rpf() function is renamed to vsp1_du_atomic_update()
for consistency.
With this new API, the driver will reprogram all modified inputs
atomically before restarting the video stream.
Implement internal control of the VSP pipeline to be used by the DU
DRM/KMS driver when using the VSP as an internal composer handled
through DRM/KMS only.
[media] v4l: vsp1: Don't validate links when the userspace API is disabled
As the pipeline is configured internally by the driver when the
userspace API is disabled its configuration can be trusted and link
validation isn't needed.
[media] v4l: vsp1: Set the alpha value manually in RPF and WPF s_stream handlers
The RPF and WPF alpha values are set through V4L2 controls and applied
when starting the video stream by a call to v4l2_ctrl_handler_setup().
As that function uses the control handler mutex it can't be called in
interrupt context, where the VSP+DU pipeline handler might need to
reconfigure the pipeline.
Set the alpha value manually in the RPF and WPF s_stream handler to
ensure that the hardware is properly configured even when controlled
without the userspace API. If the userspace API is enabled protect that
with the control lock to avoid race conditions with userspace.
[media] v4l: vsp1: Make pipeline inputs array index by RPF index
The pipeline inputs array stores pointers to all RPFs contained in the
pipeline. It's currently indexed contiguously by adding RPFs in the
order they are found during graph walk. This can't easily support
dynamic addition and removal of RPFs while streaming, which will be
required for combined VSP+DU support.
Make the array indexed by RPF index instead and skip NULL elements when
iterating over RPFs.
[media] v4l: vsp1: Make the userspace API optional
The R-Car Gen3 SoCs include VSP instances dedicated to the DU that will
be controlled entirely by the rcar-du-drm driver through the KMS API. To
support that use case make the userspace V4L2 API optional.
Laurent Pinchart [Fri, 14 Aug 2015 16:53:45 +0000 (13:53 -0300)]
[media] v4l: vsp1: Make the BRU optional
Not all VSP instances have a BRU on R-Car Gen3, make it optional. Set
the feature unconditionally for now, this will be fixed when adding Gen3
support.
[media] v4l: vsp1: Make number of BRU inputs configurable
The R-Car Gen3 family has 5-inputs BRUs, support them by making the
number of BRU inputs configurable.
As the driver assumes that the number of BRU inputs is equal to the
number of RPFs, replace the BRU_MAX_INPUTS macro with VSP1_MAX_RPF to
make the assumption apparent.
[media] v4l: vsp1: Set the SRU CTRL0 register when starting the stream
Commit 58f896d859ce ("[media] v4l: vsp1: sru: Make the intensity
controllable during streaming") refactored the stream start code and
removed the SRU CTRL0 register write by mistake. Add it back.
Fixes: 58f896d859ce ("[media] v4l: vsp1: sru: Make the intensity controllable during streaming") Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] v4l: vsp1: Decouple pipeline end of frame processing from vsp1_video
To make the pipeline structure and operations usable without video
devices the frame end processing must be decoupled from struct
vsp1_video. Implement this by calling the video frame end function
indirectly through a function pointer in struct vsp1_pipeline.
[media] v4l: vsp1: Make rwpf operations independent of video device
The rwpf queue operation doesn't queue a buffer but sets the memory
address for the next run. Rename it to set_memory and pass it a new
structure independent of the video buffer than only contains memory
information.
[media] v4l: vsp1: Move video device out of struct vsp1_rwpf
To make the video device nodes optional we need to decouple the [rw]pf
instances from the video devices. Move video devices out of struct
vsp1_rwpf and instantiate them dynamically in the core driver code.
[media] v4l: vsp1: Change the type of the rwpf field in struct vsp1_video
The rwpf field contains a pointer to the rpf or wpf associated with the
video node. Instead of storing it as a vsp1_entity, store the
corresponding vsp1_rwpf pointer to allow accessing the vsp1_rwpf fields
directly.
ti-vpe/cal.c:387:26: warning: incorrect type in return expression (different address spaces)
ti-vpe/cal.c:459:26: warning: incorrect type in return expression (different address spaces)
ti-vpe/cal.c:503:27: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:509:47: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:518:47: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:526:31: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:1807:24: warning: Using plain integer as NULL pointer
ti-vpe/cal.c:1844:16: warning: Using plain integer as NULL pointer
Wu-Cheng Li [Tue, 19 Jan 2016 07:07:10 +0000 (05:07 -0200)]
[media] s5p-mfc: add the support of V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME
There is a new control V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME to
force an encoder key frame. It is the same as requesting
V4L2_MPEG_MFC51_VIDEO_FORCE_FRAME_TYPE_I_FRAME.
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some drivers also need a control like
V4L2_CID_MPEG_MFC51_VIDEO_FORCE_FRAME_TYPE to force an encoder
key frame. Add a general V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME
so the new drivers and applications can use it.
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sudip Mukherjee [Fri, 12 Feb 2016 10:53:28 +0000 (08:53 -0200)]
[media] media: ti-vpe: add dependency of HAS_DMA
The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:492:28: error: implicit
declaration of function 'dma_get_cache_alignment'
The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_TI_CAL also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Fixes: 343e89a792a5 ("[media] media: ti-vpe: Add CAL v4l2 camera capture driver") Cc: Benoit Parrot <bparrot@ti.com> Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Wed, 10 Feb 2016 07:40:56 +0000 (05:40 -0200)]
[media] timblogiw: move to staging in preparation for removal
The Timberdale FPGA video driver has not seen any real development
since 2011 (and very little before that).
One of the problems with the timblogiw driver is that it uses videobuf
instead of the newer vb2 framework. The long term goal is to either
convert or remove any driver still using videobuf. Since none of the
core v4l developers has the hardware, we cannot convert it ourselves.
As far as I can tell it was only used in an Intel demo board in 2009
using Meego:
Moving this driver to staging is the first step towards removal. After 2 or
3 kernel cycles it will be removed altogether unless someone steps up to
clean up this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Richard Röjfors <richard@puffinpack.se> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Wed, 10 Feb 2016 11:32:25 +0000 (09:32 -0200)]
[media] adv7511: TX_EDID_PRESENT is still 1 after a disconnect
The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present.
The adv7511 however still reported the EDID present after disconnecting
the HDMI cable. Fix the logic regarding this control. And when the EDID
is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver.
This was also missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: <stable@vger.kernel.org> # for v3.12 and up Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Dan Carpenter [Tue, 9 Feb 2016 11:14:12 +0000 (09:14 -0200)]
[media] usb/cpia2_core: clean up a min_t() cast
It makes sense to make the min_t() cast unsigned here since we don't
really want negative sizes. Making it signed causes a static checker
warning in Smatch. Smatch knows "fw->size - i" is positive but it
doesn't know that fw->size is less than INT_MAX so in theory casting it
to int might lead to a negative.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] v4l2-async: Don't fail if registered_async isn't implemented
After sub-dev registration in v4l2_async_test_notify(), the v4l2-async
core calls the registered_async callback but if a sub-dev driver does
not implement it, v4l2_subdev_call() will return a -ENOIOCTLCMD which
should not be considered an error.
Dave Airlie [Fri, 19 Feb 2016 03:10:18 +0000 (13:10 +1000)]
Merge branch 'drm-rockchip-next-2016-02-18' of https://github.com/markyzq/kernel-drm-rockchip into drm-next
add Innosilicon HDMI support.
* 'drm-rockchip-next-2016-02-18' of https://github.com/markyzq/kernel-drm-rockchip:
dt-bindings: add document for Innosilicon HDMI on Rockchip platform
drm/rockchip: hdmi: add Innosilicon HDMI support
Dave Airlie [Fri, 19 Feb 2016 02:51:43 +0000 (12:51 +1000)]
Merge tag 'drm-vc4-next-2016-02-17' of github.com:anholt/linux into drm-next
This pull request brings in overlay plane support for vc4.
* tag 'drm-vc4-next-2016-02-17' of github.com:anholt/linux:
drm/vc4: Add support for YUV planes.
drm/vc4: Add support a few more RGB display plane formats.
drm/vc4: Add support for scaling of display planes.
drm/vc4: Fix which value is being used for source image size.
drm/vc4: Add more display planes to each CRTC.
drm/vc4: Make the CRTCs cooperate on allocating display lists.
drm/vc4: Add a proper short-circut path for legacy cursor updates.
drm/vc4: Move the plane clipping/scaling setup to a separate function.
drm/vc4: Add missing __iomem annotation to hw_dlist.
drm/vc4: Improve comments on vc4_plane_state members.
Dave Airlie [Fri, 19 Feb 2016 01:13:01 +0000 (11:13 +1000)]
Merge branch 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux into drm-next
First radeon and amdgpu pull request for 4.6. Highlights:
- ACP support for APUs with i2s audio
- CS ioctl optimizations
- GPU scheduler optimizations
- GPUVM optimizations
- Initial GPU reset support (not enabled yet)
- New powerplay sysfs interface for manually selecting clocks
- Powerplay fixes
- Virtualization fixes
- Removal of hw semaphore support
- Lots of other misc fixes and cleanups
* 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux: (118 commits)
drm/amdgpu: Don't call interval_tree_remove in amdgpu_mn_destroy
drm/amdgpu: Fix race condition in amdgpu_mn_unregister
drm/amdgpu: cleanup gem init/finit
drm/amdgpu: rework GEM info printing
drm/amdgpu: print the GPU offset as well in gem_info
drm/amdgpu: optionally print the pin count in gem_info as well
drm/amdgpu: print the BO size only once in amdgpu_gem_info
drm/amdgpu: print pid as integer
drm/amdgpu: remove page flip work queue v3
drm/amdgpu: stop blocking for page filp fences
drm/amdgpu: stop calling amdgpu_gpu_reset from the flip code
drm/amdgpu: remove fence reset detection leftovers
drm/amdgpu: Fix race condition in MMU notifier release
drm/radeon: Fix WARN_ON if DRM_DP_AUX_CHARDEV is enabled
drm/amdgpu/vi: move uvd tiling config setup into uvd code
drm/amdgpu/vi: move sdma tiling config setup into sdma code
drm/amdgpu/cik: move uvd tiling config setup into uvd code
drm/amdgpu/cik: move sdma tiling config setup into sdma code
drm/amdgpu/gfx7: rework gpu_init()
drm/amdgpu/gfx: clean up harvest configuration (v2)
...
Dave Airlie [Fri, 19 Feb 2016 00:57:44 +0000 (10:57 +1000)]
Merge tag 'topic/drm-misc-2016-02-18' of git://anongit.freedesktop.org/drm-intel into drm-next
Misc stuff all over:
- more mode_fixup removal from Carlos, there's another final pile still
left.
- final bits of vgaswitcheroo from Lukas for apple gmux, we're still
discussing an api cleanup patch to make it a bit more abuse-safe as a
follow-up
- dp aux interface for userspace for tools&tests from Rafael Antognolli
- actual interface parts for dma-buf flushing for userspace mmap
- few small bits all over
- vgaswitcheroo support for apple gmux from Lukas Wunner
- checks for ->mode_fixup in non-atomic helpers from Carlos Palminha, plus
removing dummy funcs from drivers. Carlos promised to follow up with
more, since there's lots more silly dummy functions around.
- dma-buf patches from Tiago, except the ioctl itself (that needed a
respin to address review from David Herrmann)
- encoder mask for atomic from Maarten
- bunch of random things all over.