Mika Westerberg [Tue, 20 Sep 2016 12:15:22 +0000 (15:15 +0300)]
pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain
It turns out that for north and southwest communities, they can only
generate GPIO interrupts for lower 8 interrupts (IntSel value). The upper
part (8-15) can only generate GPEs (General Purpose Events).
Now the reason why EC events such as pressing hotkeys does not work if we
mask all the interrupts is that in order to generate either interrupts or
GPEs the INTMASK register must have that particular interrupt unmasked. In
case of GPEs the CPU does not trigger normal interrupt (and thus the GPIO
driver does not see it) but instead it causes SCI (System Control
Interrupt) to be triggered with the GPE in question set.
To make this all work as expected we only add those GPIOs to the IRQ domain
that can actually generate interrupts (IntSel value 0-7) and skip others.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Tue, 20 Sep 2016 12:15:21 +0000 (15:15 +0300)]
gpiolib: Make it possible to exclude GPIOs from IRQ domain
When using GPIO irqchip helpers to setup irqchip for a gpiolib based
driver, it is not possible to select which GPIOs to add to the IRQ domain.
Instead it just adds all GPIOs which is not always desired. For example
there might be GPIOs that for some reason cannot generated normal
interrupts at all.
To support this we add a flag irq_need_valid_mask to struct gpio_chip. When
this flag is set the core allocates irq_valid_mask that holds one bit for
each GPIO the chip has. By default all bits are set but drivers can
manipulate this using set_bit() and clear_bit() accordingly.
Then when gpiochip_irqchip_add() is called, this mask is checked and all
GPIOs with bit is set are added to the IRQ domain created for the GPIO
chip.
pinctrl: nomadik: don't default-flag IRQs as falling
There is no point in adding any default trigger for these
GPIO interrupts: the device tree should contain all trigger
information and the platforms using the driver boots
exclusively from device tree.
Also the boot log is nagging me to fix this:
[ 0.771057] ------------[ cut here ]------------
[ 0.775695] WARNING: CPU: 0 PID: 1 at
../drivers/gpio/gpiolib.c:1622 _gpiochip_irqchip_add+0x138/0x160
[ 0.785034] /soc/gpio@8012e000: Ignoring 2 default trigger
(...)
[ 0.942962] gpio 8012e000.gpio: at address e08f8000
(etc ad nauseam)
Suggested-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Peter Griffin [Wed, 14 Sep 2016 13:27:52 +0000 (14:27 +0100)]
pinctrl: st: Remove obsolete platforms from pinctrl-st dt doc
STiH415/6 SoC support is being removed from the kernel.
This patch updates the ST pinctrl dt doc and removes
references to these obsolete platforms. It also updates
the dt example to the currently supported STiH407
platform.
STiH415/6 SoC support is being removed from the kernel.
This patch updates the ST pinctrl driver and removes
references to these obsolete platforms. As some structures
referenced by STiH407 based configuration were shared with
STiH416 we update these names to match the remaining
supported platform.
Add EE domains pins for the NAND flash controller.
Even tough we have no driver for the NAND flash controller yet, we need
to have these pins in pinctrl as the actual pin are shared with the spifc
controller. The bootloader on the S905-P200 setup pinmux for the NAND
controller so we need the kernel to properly deactivate this if necessary.
The newly added irqchip support for the stm32 pinctrl driver uses
hierarchical IRQ domains as provided by the NVIC primary irqchip.
This works great for any configuration that may be relevant on
stm32, but when doing compile-testing (randconfig), we can
enable it without NVIC or any other primary irqchip that
enables IRQ_DOMAIN_HIERARCHY:
drivers/pinctrl/stm32/pinctrl-stm32.c:212:13: error: 'irq_chip_eoi_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:213:20: error: 'irq_chip_mask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:214:20: error: 'irq_chip_unmask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:215:20: error: 'irq_chip_set_type_parent' undeclared here (not in a function)
This adds a Kconfig dependency to limit compile-testing to
configurations that have IRQ_DOMAIN_HIERARCHY already enabled.
It's not obvious whether we should use 'depends on' or 'select'
here, I think either one works, with 'depends on' being more
intuitive, while 'select' would be less likely to cause dependency
loops.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 0eb9f683336d ("pinctrl: Add IRQ support to STM32 gpios") Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
driver: base: pinctrl: return error from pinctrl_bind_pins()
strict pin controller returns -EINVAL in case of pin request which
is already claimed by somebody else.
Following is the sequence of calling pin_request() from
pinctrl_bind_pins():-
pinctrl_bind_pins()->pinctrl_select_state()->pinmux_enable_setting()->
pin_request()
But pinctrl_bind_pins() only returns -EPROBE_DEFER which makes device
driver probe successful even if the pin request is rejected by the pin
controller subsystem.
This commit modifies pinctrl_bind_pins() to return error if the pin is
rejected by pin control subsystem.
Signed-off-by: Deepak Das <deepak_das@mentor.com>
[Rewrote to be cleaner] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: meson-gxbb: add the missing SDIO interrupt pin
This adds the SDIO interrupt pin which can be used by sd_emmc_a.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Suggested-by: Neil Armstrong <narmstrong@baylibre.com> Fixes: 29885a656511 ("pinctrl: meson-gxbb: add the pins for the
SDIO/sd_emmc_a controller") Acked-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added aspeed driver tries to check for a negative return
value from a pinctrl function, but stores the intermediate value in
a 'bool' variable, which cannot work:
drivers/pinctrl/aspeed/pinctrl-aspeed.c: In function 'aspeed_sig_expr_set':
drivers/pinctrl/aspeed/pinctrl-aspeed.c:192:11: error: comparison of constant '0' with boolean expression is always false [-Werror=bool-compare]
This slightly reworks the logic to use an explicit comparison with zero
before assigning to the temporary variable.
Reported-by: Colin King <colin.king@canonical.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The EXTI controller has 16 lines dedicated to GPIOs.
EXTI line n can be connected to only line n of one of the GPIO ports, for
example EXTI0 can be connected to either PA0, or PB0, or PC0...
This port selection is done by specifying the port number into System
Config registers.
gpio: mxc: add generic gpio request/free callbacks to pinctrl
If a GPIO controller description in board DTB contains information
about mappings between GPIOs and pads under IOMUX control use it to
request and free GPIOs with respect to pinctrl/pinmux subsystems.
One of immediate positive functional changes is inability to
request non-existing GPIOs, i.e. if there is no pad such. Also
pinctrl/pinmux may now properly account pads occupied by requested
GPIOs.
The change has no effect, if "gpio-ranges" property is not found
including the case if a board has no DTB firmware.
gpio: mxc: shift gpio_mxc_init() to subsys_initcall level
In general situation on-SoC GPIO controller drivers should be probed
after pinctrl/pinmux controller driver, because on-SoC GPIOs utilize a
pin/pad as a resource provided and controlled by pinctrl subsystem.
This is stated in multiple places, e.g. from drivers/Makefile:
GPIO must come after pinctrl as gpios may need to mux pins etc
Looking at Freescale iMX SoC series specifics, imx*_pinctrl_init()
functions are called at arch_initcall and postcore_initcall init
levels, so the change of initcall level for gpio-mxc driver from
postcore_initcall to subsys_initcall level is sufficient. Also note
that the most of GPIO controller drivers settled at subsys_initcall
level.
If pinctrl subsystem manages pads with GPIO functions, the change is
needed to avoid unwanted driver probe deferrals during kernel boot.
pinctrl: imx: accept gpio request/free from pinctrl
While only Freescale Vybrid SoC has settings of GPIO capabilities done
by iomux controller, it is only a matter of GPIO controller driver
implementation for the rest of Freescale/NXP SoCs from iMX series.
As a practical example on GPIO request a pad function should be
switched to GPIO, but because this requires updates to all particular
iMX pinctrl drivers, for simplicity at the moment add only a proper
connection between shared pinctrl-imx and pinctrl/pinmux core, namely
.gpio_request_enable/.gpio_disable_free/.gpio_set_direction callbacks
should return success to a caller. This change allows to progress by
adding request/free callbacks into gpio-mxc.c driver.
Marc Zyngier [Tue, 6 Sep 2016 13:58:15 +0000 (14:58 +0100)]
pinctrl/at91: Don't provide a default trigger type
at91 used to set a default trigger type for GPIO interrupts in
order to cope with the old board files. These days are long gone,
and it all gets probed through DT.
Andras Szemzo reported that the Ethernet device on his board was
bailing to be probed, due to a conflict in interrupt trigger.
Surely enough, this is due to this default trigger still being
present, and turning this into a IRQ_TYPE_NONE fixes the issue.
pinctrl: sh-pfc: Return pinconf with arguments in packed format
The pinconf-generic code expects configurations with arguments to be
returned in a packed format in order to be displayed properly by
pinconf_generic_dump_one().
Reading /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins on
r8a7795/salvator-x now shows:
Commit aa71987472a9 ("nvme: fabrics drivers don't need the nvme-pci
driver") removed the dependency on BLK_DEV_NVME, but the cdoe does
depend on the block layer (which used to be an implicit dependency
through BLK_DEV_NVME).
Otherwise you get various errors from the kbuild test robot random
config testing when that happens to hit a configuration with BLOCK
device support disabled.
Cc: Christoph Hellwig <hch@lst.de> Cc: Jay Freyensee <james_p_freyensee@linux.intel.com> Cc: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are a few small IIO fixes for 4.8-rc6.
Nothing major, full details are in the shortlog, all of these have
been in linux-next with no reported issues"
* tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio:core: fix IIO_VAL_FRACTIONAL sign handling
iio: ensure ret is initialized to zero before entering do loop
iio: accel: kxsd9: Fix scaling bug
iio: accel: bmc150: reset chip at init time
iio: fix pressure data output unit in hid-sensor-attributes
tools:iio:iio_generic_buffer: fix trigger-less mode
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"nvdimm fixes for v4.8, two of them are tagged for -stable:
- Fix devm_memremap_pages() to use track_pfn_insert(). Otherwise,
DAX pmd mappings end up with an uncached pgprot, and unusable
performance for the device-dax interface. The device-dax interface
appeared in 4.7 so this is tagged for -stable.
- Fix a couple VM_BUG_ON() checks in the show_smaps() path to
understand DAX pmd entries. This fix is tagged for -stable.
- Fix a mis-merge of the nfit machine-check handler to flip the
polarity of an if() to match the final version of the patch that
Vishal sent for 4.8-rc1. Without this the nfit machine check
handler never detects / inserts new 'badblocks' entries which
applications use to identify lost portions of files.
- For test purposes, fix the nvdimm_clear_poison() path to operate on
legacy / simulated nvdimm memory ranges. Without this fix a test
can set badblocks, but never clear them on these ranges.
- Fix the range checking done by dax_dev_pmd_fault(). This is not
tagged for -stable since this problem is mitigated by specifying
aligned resources at device-dax setup time.
These patches have appeared in a next release over the past week. The
recent rebase you can see in the timestamps was to drop an invalid fix
as identified by the updated device-dax unit tests [1]. The -mm
touches have an ack from Andrew"
[1]: "[ndctl PATCH 0/3] device-dax test for recent kernel bugs"
https://lists.01.org/pipermail/linux-nvdimm/2016-September/006855.html
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm: allow legacy (e820) pmem region to clear bad blocks
nfit, mce: Fix SPA matching logic in MCE handler
mm: fix cache mode of dax pmd mappings
mm: fix show_smap() for zone_device-pmd ranges
dax: fix mapping size check
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Mostly driver bugfixes, but also a few cleanups which are nice to have
out of the way"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rk3x: Restore clock settings at resume time
i2c: Spelling s/acknowedge/acknowledge/
i2c: designware: save the preset value of DW_IC_SDA_HOLD
Documentation: i2c: slave-interface: add note for driver development
i2c: mux: demux-pinctrl: run properly with multiple instances
i2c: bcm-kona: fix inconsistent indenting
i2c: rcar: use proper device with dma_mapping_error
i2c: sh_mobile: use proper device with dma_mapping_error
i2c: mux: demux-pinctrl: invalidate properly when switching fails
Merge tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull fscrypto fixes fromTed Ts'o:
"Fix some brown-paper-bag bugs for fscrypto, including one one which
allows a malicious user to set an encryption policy on an empty
directory which they do not own"
* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
fscrypto: require write access to mount to set encryption policy
fscrypto: only allow setting encryption policy on directories
fscrypto: add authorization check for setting encryption policy
Eric Biggers [Thu, 8 Sep 2016 21:20:38 +0000 (14:20 -0700)]
fscrypto: require write access to mount to set encryption policy
Since setting an encryption policy requires writing metadata to the
filesystem, it should be guarded by mnt_want_write/mnt_drop_write.
Otherwise, a user could cause a write to a frozen or readonly
filesystem. This was handled correctly by f2fs but not by ext4. Make
fscrypt_process_policy() handle it rather than relying on the filesystem
to get it right.
Signed-off-by: Eric Biggers <ebiggers@google.com> Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs} Signed-off-by: Theodore Ts'o <tytso@mit.edu> Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>
Eric Biggers [Thu, 8 Sep 2016 18:36:39 +0000 (11:36 -0700)]
fscrypto: only allow setting encryption policy on directories
The FS_IOC_SET_ENCRYPTION_POLICY ioctl allowed setting an encryption
policy on nondirectory files. This was unintentional, and in the case
of nonempty regular files did not behave as expected because existing
data was not actually encrypted by the ioctl.
In the case of ext4, the user could also trigger filesystem errors in
->empty_dir(), e.g. due to mismatched "directory" checksums when the
kernel incorrectly tried to interpret a regular file as a directory.
This bug affected ext4 with kernels v4.8-rc1 or later and f2fs with
kernels v4.6 and later. It appears that older kernels only permitted
directories and that the check was accidentally lost during the
refactoring to share the file encryption code between ext4 and f2fs.
This patch restores the !S_ISDIR() check that was present in older
kernels.
Signed-off-by: Eric Biggers <ebiggers@google.com> Cc: stable@vger.kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Eric Biggers [Thu, 8 Sep 2016 17:57:08 +0000 (10:57 -0700)]
fscrypto: add authorization check for setting encryption policy
On an ext4 or f2fs filesystem with file encryption supported, a user
could set an encryption policy on any empty directory(*) to which they
had readonly access. This is obviously problematic, since such a
directory might be owned by another user and the new encryption policy
would prevent that other user from creating files in their own directory
(for example).
Fix this by requiring inode_owner_or_capable() permission to set an
encryption policy. This means that either the caller must own the file,
or the caller must have the capability CAP_FOWNER.
(*) Or also on any regular file, for f2fs v4.6 and later and ext4
v4.8-rc1 and later; a separate bug fix is coming for that.
Dave Jiang [Fri, 9 Sep 2016 16:10:08 +0000 (09:10 -0700)]
libnvdimm: allow legacy (e820) pmem region to clear bad blocks
Bad blocks can be injected via /sys/block/pmemN/badblocks. In a situation
where legacy pmem is being used or a pmem region created by using memmap
kernel parameter, the injected bad blocks are not cleared due to
nvdimm_clear_poison() failing from lack of ndctl function pointer. In
this case we need to just return as handled and allow the bad blocks to
be cleared rather than fail.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The check for a 'pmem' type SPA in the MCE handler was inverted due to a
merge/rebase error.
Fixes: 6839a6d nfit: do an ARS scrub on hitting a latent media error Cc: linux-acpi@vger.kernel.org Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Wed, 7 Sep 2016 15:51:21 +0000 (08:51 -0700)]
mm: fix cache mode of dax pmd mappings
track_pfn_insert() in vmf_insert_pfn_pmd() is marking dax mappings as
uncacheable rendering them impractical for application usage. DAX-pte
mappings are cached and the goal of establishing DAX-pmd mappings is to
attain more performance, not dramatically less (3 orders of magnitude).
track_pfn_insert() relies on a previous call to reserve_memtype() to
establish the expected page_cache_mode for the range. While memremap()
arranges for reserve_memtype() to be called, devm_memremap_pages() does
not. So, teach track_pfn_insert() and untrack_pfn() how to handle
tracking without a vma, and arrange for devm_memremap_pages() to
establish the write-back-cache reservation in the memtype tree.
Cc: <stable@vger.kernel.org> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Toshi Kani <toshi.kani@hpe.com> Reported-by: Kai Zhang <kai.ka.zhang@oracle.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
These locations are sanity checking page flags that must be set for an
anonymous transparent huge page, but are not set for the zone_device
pages associated with dax mappings.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"This includes a couple of bugfixs for virtio.
The virtio console patch is actually also in x86/tip targeting 4.9
because it helps vmap stacks, but it also fixes IOMMU_PLATFORM which
was added in 4.8, and it seems important not to ship that in a broken
configuration"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: Stop doing DMA on the stack
virtio: mark vring_dma_dev() static
Merge tag 'pm-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"This includes a PM QoS framework fix from Tejun to prevent interrupts
from being enabled unexpectedly during early boot and a cpufreq
documentation fix.
Specifics:
- If the PM QoS framework invokes cancel_delayed_work_sync() during
early boot, it will enable interrupts which is not expected at that
point, so prevent it from happening (Tejun Heo)
- Fix cpufreq statistic documentation to follow a recent change in
behavior that forgot to update it as appropriate (Jean Delvare)"
* tag 'pm-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq-stats: Minor documentation fix
PM / QoS: avoid calling cancel_delayed_work_sync() during early boot
Merge tag 'gpio-v4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes that have been boiling the last two weeks or so.
Nothing special, I'm trying to sort out some Kconfig business and
Russell needs a fix in for -his SA1100 rework.
Summary:
- Revert a pointless attempt to add an include to solve the UM allyes
compilation problem.
- Make the mcp23s08 depend on OF_GPIO as it uses it and doesn't
compile properly without it.
- Fix a probing problem for ucb1x00"
* tag 'gpio-v4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: sa1100: fix irq probing for ucb1x00
gpio: mcp23s08: make driver depend on OF_GPIO
Revert "gpio: include <linux/io-mapping.h> in gpiolib-of"
Merge branch 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I'm not proud of how long it took me to track down that one liner in
btrfs_sync_log(), but the good news is the patches I was trying to
blame for these problems were actually fine (sorry Filipe)"
* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: introduce tickets_id to determine whether asynchronous metadata reclaim work makes progress
btrfs: remove root_log_ctx from ctx list before btrfs_sync_log returns
btrfs: do not decrease bytes_may_use when replaying extents
Merge tag 'sound-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"We've got quite a few fixes at this time, and all are stable patches.
syzkaller strikes back again (episode 19 or so), and we had to plug
some holes in ALSA core part (mostly timer).
In addition, a couple of FireWire audio fixes for the invalid copy
user calls in locks, and a few quirks for HD-audio and USB-audio as
usual are included"
* tag 'sound-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: rawmidi: Fix possible deadlock with virmidi registration
ALSA: timer: Fix zero-division by continue of uninitialized instance
ALSA: timer: fix NULL pointer dereference in read()/ioctl() race
ALSA: fireworks: accessing to user space outside spinlock
ALSA: firewire-tascam: accessing to user space outside spinlock
ALSA: hda - Enable subwoofer on Dell Inspiron 7559
ALSA: hda - Add headset mic quirk for Dell Inspiron 5468
ALSA: usb-audio: Add sample rate inquiry quirk for B850V3 CP2114
ALSA: timer: fix NULL pointer dereference on memory allocation failure
ALSA: timer: fix division by zero after SNDRV_TIMER_IOCTL_CONTINUE
Andy Lutomirski [Tue, 30 Aug 2016 15:04:15 +0000 (08:04 -0700)]
virtio_console: Stop doing DMA on the stack
virtio_console uses a small DMA buffer for control requests. Move
that buffer into heap memory.
Doing virtio DMA on the stack is normally okay on non-DMA-API virtio
systems (which is currently most of them), but it breaks completely
if the stack is virtually mapped.
Tested by typing both directions using picocom aimed at /dev/hvc0.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Amit Shah <amit.shah@redhat.com>
We get 1 warning when building kernel with W=1:
drivers/virtio/virtio_ring.c:170:16: warning: no previous prototype for 'vring_dma_dev' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- smp_mb__before_spinlock() changed to smp_mb() on arm64 since the
generic definition to smp_wmb() is not sufficient
- avoid a recursive loop with the graph tracer by using using
preempt_(enable|disable)_notrace in _percpu_(read|write)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: use preempt_disable_notrace in _percpu_read/write
arm64: spinlocks: implement smp_mb__before_spinlock() as smp_mb()
Merge tag 'powerpc-4.8-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Don't alias user region to other regions below PAGE_OFFSET from
Paul Mackerras
- Fix again csum_partial_copy_generic() on 32-bit from Christophe
Leroy
- Fix corrupted PE allocation bitmap on releasing PE from Gavin Shan
Fixes for code merged this cycle:
- Fix crash on releasing compound PE from Gavin Shan
- Fix processor numbers in OPAL ICP from Benjamin Herrenschmidt
- Fix little endian build with CONFIG_KEXEC=n from Thiago Jung
Bauermann"
* tag 'powerpc-4.8-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Don't alias user region to other regions below PAGE_OFFSET
powerpc/32: Fix again csum_partial_copy_generic()
powerpc/powernv: Fix corrupted PE allocation bitmap on releasing PE
powerpc/powernv: Fix crash on releasing compound PE
powerpc/xics/opal: Fix processor numbers in OPAL ICP
powerpc/pseries: Fix little endian build with CONFIG_KEXEC=n
Merge tag 'fixes-for-v4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.8-rc6
Unfortunately we have a bogus dwc3 patch leaked through the cracks and
got merged into Linus' HEAD. That patch ended up causing off-by-1 error
in our TRB accounting logic. Thankfully John Youn found out the problem
and we provided a revert to the bogus dwc3 patch in no time.
Apart from this off-by-1 error, we have two fixes to the Renesas drivers,
a small fix to our generic phy driver, a NULL pointer dereference fix for
f_eem and a build warning fix in dwc3.
Merge tag 'iio-fixes-for-4.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.8 cycle.
We have a big rework of the kxsd9 driver queued up behind the fix below and
a fix for a recent fix that was marked for stable.
Hence this fix series is perhaps a little more urgent than average for IIO.
* core
- a fix for a fix in the last set. The recent fix for blocking ops when
! task running left a path (unlikely one) in which the function return
value was not set - so initialise it to 0.
- The IIO_TYPE_FRACTIONAL code previously didn't cope with negative
fractions. Turned out a fix for this was in Analog's tree but hadn't made
it upstream.
* bmc150
- reset chip at init time. At least one board out there ends up coming up
in an unstable state due to noise during power up. The reset does no
harm on other boards.
* kxsd9
- Fix a bug in the reported scaling due to failing to set the integer
part to 0.
* hid-sensors-pressure
- Output was in the wrong units to comply with the IIO ABI.
* tools
- iio_generic_buffer: Fix the trigger-less mode by ensuring we don't fault
out for having no trigger when we explicitly said we didn't want to have
one.
arm64: use preempt_disable_notrace in _percpu_read/write
When debug preempt or preempt tracer is enabled, preempt_count_add/sub()
can be traced by function and function graph tracing, and
preempt_disable/enable() would call preempt_count_add/sub(), so in Ftrace
subsystem we should use preempt_disable/enable_notrace instead.
In the commit 345ddcc882d8 ("ftrace: Have set_ftrace_pid use the bitmap
like events do") the function this_cpu_read() was added to
trace_graph_entry(), and if this_cpu_read() calls preempt_disable(), graph
tracer will go into a recursive loop, even if the tracing_on is
disabled.
So this patch change to use preempt_enable/disable_notrace instead in
this_cpu_read().
Since Yonghui Yang helped a lot to find the root cause of this problem,
so also add his SOB.
Signed-off-by: Yonghui Yang <mark.yang@spreadtrum.com> Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Mon, 5 Sep 2016 10:56:05 +0000 (11:56 +0100)]
arm64: spinlocks: implement smp_mb__before_spinlock() as smp_mb()
smp_mb__before_spinlock() is intended to upgrade a spin_lock() operation
to a full barrier, such that prior stores are ordered with respect to
loads and stores occuring inside the critical section.
Unfortunately, the core code defines the barrier as smp_wmb(), which
is insufficient to provide the required ordering guarantees when used in
conjunction with our load-acquire-based spinlock implementation.
This patch overrides the arm64 definition of smp_mb__before_spinlock()
to map to a full smp_mb().
Cc: <stable@vger.kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Reported-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Clemens Gruber [Mon, 5 Sep 2016 17:29:58 +0000 (19:29 +0200)]
usb: chipidea: udc: fix NULL ptr dereference in isr_setup_status_phase
Problems with the signal integrity of the high speed USB data lines or
noise on reference ground lines can cause the i.MX6 USB controller to
violate USB specs and exhibit unexpected behavior.
It was observed that USBi_UI interrupts were triggered first and when
isr_setup_status_phase was called, ci->status was NULL, which lead to a
NULL pointer dereference kernel panic.
This patch fixes the kernel panic, emits a warning once and returns
-EPIPE to halt the device and let the host get stalled.
It also adds a comment to point people, who are experiencing this issue,
to their USB hardware design.
Cc: <stable@vger.kernel.org> #4.1+ Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Peter Chen <peter.chen@nxp.com>
Jean Delvare [Thu, 8 Sep 2016 21:05:07 +0000 (23:05 +0200)]
cpufreq-stats: Minor documentation fix
The cpufreq-stats code can no longer be built as a module, so it now
appears with square brackets in menuconfig.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: 1aefc75b2449 (cpufreq: stats: Make the stats code non-modular) Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Doug Anderson [Mon, 29 Aug 2016 21:22:36 +0000 (14:22 -0700)]
i2c: rk3x: Restore clock settings at resume time
Depending on a number of factors including:
- Which exact Rockchip SoC we're working with
- How deep we suspend
- Which i2c port we're on
We might lose the state of the i2c registers at suspend time.
Specifically we've found that on rk3399 the i2c ports that are not in
the PMU power domain lose their state with the current suspend depth
configured by ARM Tursted Firmware.
Note that there are very few actual i2c registers that aren't configured
per transfer anyway so all we actually need to re-configure are the
clock config registers. We'll just add a call to rk3x_i2c_adapt_div()
at resume time and be done with it.
NOTE: On rk3399 on ports whose power was lost, I put printouts in at
resume time. I saw things like:
before: con=0x00010300, div=0x00060006
after: con=0x00010200, div=0x00180025
Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: David Wu <david.wu@rock-chips.com> Tested-by: David Wu <david.wu@rock-chips.com>
[wsa: removed duplicate const] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Zhuo-hao Lee [Sat, 27 Aug 2016 07:39:30 +0000 (15:39 +0800)]
i2c: designware: save the preset value of DW_IC_SDA_HOLD
There are several ways to set the SDA hold time for i2c controller,
including: Device Tree, built-in device properties and ACPI. However,
if the SDA hold time is not specified by above method, we should
read the value, where it is preset by firmware, and save it to
sda_hold_time. This is needed because when i2c controller enters
runtime suspend, the DW_IC_SDA_HOLD value will be reset to chipset
default value. And during runtime resume, i2c_dw_init will be called
to reconfigure i2c controller. If sda_hold_time is zero, the chipset
default hold time will be used, that will be too short for some
platforms. Therefore, to have a better tolerance, the DW_IC_SDA_HOLD
value should be kept by sda_hold_time.
Signed-off-by: Zhuo-hao Lee <zhuo-hao.lee@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a slightly larger batch of fixes that we've been sitting on a
few -rcs. Most of them are simple oneliners, but there are two sets
that are slightly larger and worth pointing out:
- A set of patches to OMAP to deal with hwmod for RTC on am33xx
(beaglebone SoC, among others). It's the only clock that ever has
a valid offset of 0, so a new flag needed introduction once this
problem was discovered.
- A collection of CCI fixes for performance counters discovered once
people started using it on X-Gene CPUs"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
arm-cci: pmu: Fix typo in event name
Revert "ARM: tegra: fix erroneous address in dts"
ARM: dts: imx6qdl: Fix SPDIF regression
ARM: imx6: add missing BM_CLPCR_BYPASS_PMIC_READY setting for imx6sx
ARM: dts: imx7d-sdb: fix ti,x-plate-ohms property name
ARM: dts: kirkwood: Fix PCIe label on OpenRD
ARM: kirkwood: ib62x0: fix size of u-boot environment partition
bus: arm-ccn: make event groups reliable
bus: arm-ccn: fix hrtimer registration
bus: arm-ccn: fix PMU interrupt flags
ARM: tegra: Correct polarity for Tegra114 PMIC interrupt
MAINTAINERS: add tree entry for ARM/UniPhier architecture
ARM: sun5i: Fix typo in trip point temperature
MAINTAINERS: Switch to kernel.org account for Krzysztof Kozlowski
ARM: imx6ul: populates platform device at .init_machine
bus: arm-ccn: Add missing event attribute exclusions for host/guest
bus: arm-ccn: Correct required arguments for XP PMU events
bus: arm-ccn: Fix XP watchpoint settings bitmask
bus: arm-ccn: Do not attempt to configure XPs for cycle counter
bus: arm-ccn: Fix PMU handling of MN
...
Takashi Iwai [Tue, 30 Aug 2016 12:45:46 +0000 (14:45 +0200)]
ALSA: rawmidi: Fix possible deadlock with virmidi registration
When a seq-virmidi driver is initialized, it registers a rawmidi
instance with its callback to create an associated seq kernel client.
Currently it's done throughly in rawmidi's register_mutex context.
Recently it was found that this may lead to a deadlock another rawmidi
device that is being attached with the sequencer is accessed, as both
open with the same register_mutex. This was actually triggered by
syzkaller, as Dmitry Vyukov reported:
======================================================
[ INFO: possible circular locking dependency detected ]
4.8.0-rc1+ #11 Not tainted
-------------------------------------------------------
syz-executor/7154 is trying to acquire lock:
(register_mutex#5){+.+.+.}, at: [<ffffffff84fd6d4b>] snd_rawmidi_kernel_open+0x4b/0x260 sound/core/rawmidi.c:341
but task is already holding lock:
(&grp->list_mutex){++++.+}, at: [<ffffffff850138bb>] check_and_subscribe_port+0x5b/0x5c0 sound/core/seq/seq_ports.c:495
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
The fix is to simply move the registration parts in
snd_rawmidi_dev_register() to the outside of the register_mutex lock.
The lock is needed only to manage the linked list, and it's not
necessarily to cover the whole initialization process.
Although a similar issue was spotted and a fix patch was merged in
commit [6b760bb2c63a: ALSA: timer: fix division by zero after
SNDRV_TIMER_IOCTL_CONTINUE], it seems covering only a part of
iceberg.
In this patch, we fix the issue a bit more drastically. Basically the
continue of an uninitialized timer is supposed to be a fresh start, so
we do it for user timers. For the direct snd_timer_continue() call,
there is no way to pass the initial tick value, so we kick out for the
uninitialized case.
Allen Hung [Fri, 15 Jul 2016 09:42:22 +0000 (17:42 +0800)]
dmi-id: don't free dev structure after calling device_register
dmi_dev is freed in error exit code but, according to the document
of device_register, it should never directly free device structure
after calling this function, even if it returned an error! Use
put_device() instead.
Signed-off-by: Allen Hung <allen_hung@dell.com> Signed-off-by: Jean Delvare <jdelvare@suse.de>
xhci: fix null pointer dereference in stop command timeout function
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
For one of the CCI events exposed under sysfs, "snoop" was typo'd as
"snopp". Correct this such that users see the expected event name when
enumerating events via sysfs.
Cc: arm@kernel.org Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 8 Sep 2016 04:24:22 +0000 (21:24 -0700)]
Merge tag 'imx-fixes-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.8, 2nd round:
- Fix misspelled "ti,x-plate-ohms" property name of touchscreen
controller for imx7d-sdb DTS.
- Add missing BM_CLPCR_BYPASS_PMIC_READY setting for i.MX6SX to get
suspend/resume work properly.
- Fix SPDIF regression on imx6qdl which caused by a clock update on
spdif device node.
* tag 'imx-fixes-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl: Fix SPDIF regression
ARM: imx6: add missing BM_CLPCR_BYPASS_PMIC_READY setting for imx6sx
ARM: dts: imx7d-sdb: fix ti,x-plate-ohms property name
This is no longer needed due to other changes going into 4.8 to rename
the unit addresses on a large number of device nodes. So it was picked up
for v4.8-rc1 in error.
Reported-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de> Signed-off-by: Olof Johansson <olof@lixom.net>
Paul Mackerras [Fri, 2 Sep 2016 11:47:59 +0000 (21:47 +1000)]
powerpc/mm: Don't alias user region to other regions below PAGE_OFFSET
In commit c60ac5693c47 ("powerpc: Update kernel VSID range", 2013-03-13)
we lost a check on the region number (the top four bits of the effective
address) for addresses below PAGE_OFFSET. That commit replaced a check
that the top 18 bits were all zero with a check that bits 46 - 59 were
zero (performed for all addresses, not just user addresses).
This means that userspace can access an address like 0x1000_0xxx_xxxx_xxxx
and we will insert a valid SLB entry for it. The VSID used will be the
same as if the top 4 bits were 0, but the page size will be some random
value obtained by indexing beyond the end of the mm_ctx_high_slices_psize
array in the paca. If that page size is the same as would be used for
region 0, then userspace just has an alias of the region 0 space. If the
page size is different, then no HPTE will be found for the access, and
the process will get a SIGSEGV (since hash_page_mm() will refuse to create
a HPTE for the bogus address).
The access beyond the end of the mm_ctx_high_slices_psize can be at most
5.5MB past the array, and so will be in RAM somewhere. Since the access
is a load performed in real mode, it won't fault or crash the kernel.
At most this bug could perhaps leak a little bit of information about
blocks of 32 bytes of memory located at offsets of i * 512kB past the
paca->mm_ctx_high_slices_psize array, for 1 <= i <= 11.
Christophe Leroy [Fri, 26 Aug 2016 14:45:13 +0000 (16:45 +0200)]
powerpc/32: Fix again csum_partial_copy_generic()
Commit 7aef4136566b0 ("powerpc32: rewrite csum_partial_copy_generic()
based on copy_tofrom_user()") introduced a bug when destination address
is odd and len is lower than cacheline size.
In that case the resulting csum value doesn't have to be rotated one
byte because the cache-aligned copy part is skipped so no alignment
is performed.
Fixes: 7aef4136566b0 ("powerpc32: rewrite csum_partial_copy_generic() based on copy_tofrom_user()") Cc: stable@vger.kernel.org # v4.6+ Reported-by: Alessio Igor Bogani <alessio.bogani@elettra.eu> Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Tested-by: Alessio Igor Bogani <alessio.bogani@elettra.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/powernv: Fix corrupted PE allocation bitmap on releasing PE
In pnv_ioda_free_pe(), the PE object (including the associated PE
number) is cleared before resetting the corresponding bit in the
PE allocation bitmap. It means PE#0 is always released to the bitmap
wrongly.
This fixes above issue by caching the PE number before the PE object
is cleared.
Fixes: 1e9167726c41 ("powerpc/powernv: Use PE instead of number during setup and release" Cc: stable@vger.kernel.org # v4.7+ Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Russell King [Mon, 29 Aug 2016 10:24:10 +0000 (11:24 +0100)]
gpio: sa1100: fix irq probing for ucb1x00
ucb1x00 has used IRQ probing since it's dawn to find the GPIO interrupt
that it's connected to. However, commit 23393d49fb75 ("gpio: kill off
set_irq_flags usage") broke this by disabling IRQ probing on GPIO
interrupts. Fix this.
Fixes: 23393d49fb75 ("gpio: kill off set_irq_flags usage") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MCP23S08 driver certainly accesses fields inside the
struct gpio_chip that are only available under CONFIG_OF_GPIO
not just CONFIG_OF, so update the Kconfig and driver to reflect
this.
Cc: Alexander Stein <alexander.stein@systec-electronic.com> Cc: Phil Reid <preid@electromag.com.au> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge tag 'usercopy-v4.8-rc6-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more hardened usercopyfixes from Kees Cook:
- force check_object_size() to be inline too
- move page-spanning check behind a CONFIG since it's triggering false
positives
[ Changed the page-spanning config option to depend on EXPERT in the
merge. That way it still gets build testing, and you can enable it if
you want to, but is never enabled for "normal" configurations ]
* tag 'usercopy-v4.8-rc6-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
usercopy: remove page-spanning test for now
usercopy: force check_object_size() inline
Julia Lawall [Thu, 1 Sep 2016 18:42:21 +0000 (20:42 +0200)]
pinctrl: bcm281xx: constify pinctrl_ops and pinmux_ops structures
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
Julia Lawall [Thu, 1 Sep 2016 18:42:20 +0000 (20:42 +0200)]
pinctrl: nsp: constify pinctrl_ops and pinmux_ops structures
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
Julia Lawall [Thu, 1 Sep 2016 18:42:19 +0000 (20:42 +0200)]
pinctrl: ns2: constify pinctrl_ops and pinmux_ops structures
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
pinctrl/amd: Configure GPIO register using BIOS settings
In the function amd_gpio_irq_set_type, use the settings provided by
the BIOS,when the LevelTrig is Edge and activeLevel is HIGH, to configure
the GPIO registers. Ignore the settings from client.
A custom allocator without __GFP_COMP that copies to userspace has been
found in vmw_execbuf_process[1], so this disables the page-span checker
by placing it behind a CONFIG for future work where such things can be
tracked down later.
projects / linux-beck.git / log