Johannes Berg [Mon, 20 Apr 2009 23:36:59 +0000 (01:36 +0200)]
mac80211: fix alignment calculation bug
When checking whether or not a given frame needs to be
moved to be properly aligned to a 4-byte boundary, we
use & 4 which wasn't intended, this code should check
the lowest two bits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is expected that config interface will always succeed as mac80211
will only request what driver supports. The exception here is when a
device has rfkill enabled. At this time the rfkill state is unknown to
mac80211 and config interface can fail. When this happens we deal with
this error instead of printing a WARN.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jay Sternberg [Mon, 20 Apr 2009 21:36:54 +0000 (14:36 -0700)]
iwlwifi: fix EEPROM validation mask to include OTP only devices
Fix the bug where some revisions of 6000 series hardware cannot
be used. Later versions of 6000 series have the EEPROM replaced by
OTP. For these devices to be used we need to expand valid EEPROM mask.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Dreier [Mon, 20 Apr 2009 18:32:08 +0000 (18:32 +0000)]
mlx4_en: Fix cleanup if workqueue create in mlx4_en_add() fails
If creating a workqueue fails, don't jump to the error path where that
same workqueue is destroyed, since destroy_workqueue() can't handle a
NULL pointer.
This was spotted by the Coverity checker (CID 2617).
Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en: Move to SW counters for total bytes and packets
The per ring counters are implemented in SW. Now moving to have the total
counters as the sum of all rings. This way the numbers will always be consistent
and we no longer depend on HW buffer size limitations for those counters
that can be insufficient in some cases.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en: use NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM for tx csum at initialization
The former usage was to set the NETIF_F_HW_CSUM flag which is not used
in get_tx_csum. It caused Ethtool to show tx checksum as "on" even
though it was turned off in previous operation.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en: Fix error handling while activating RX rings
In case of failure of either srq creation or page allocation,
the cleanup code handled the failed ring as well, and tried
to destroy resources that where not allocated.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 20 Apr 2009 21:52:29 +0000 (14:52 -0700)]
tg3: Fix SEEPROM accesses
The recent NVRAM patches sanitized how the driver deals with NVRAM
data, but they failed to bring the SEEPROM interfaces inline with
the new strategy. This patch brings the SEEPROM interfaces up to date.
This patch also reverts commit 0d489ffb76de0fe804cf06a9d4d11fa7342d74b9
("tg3: fix big endian MAC address collection failure").
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Tested-by: Robin Holt <holt@sgi.com> Tested-by: James Bottomley <james.bottomley@HansenPartnership.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo [Sun, 19 Apr 2009 05:47:19 +0000 (08:47 +0300)]
mac80211: fix beacon loss detection after scan
Currently beacon loss detection triggers after a scan. A probe request
is sent and a message like this is printed to the log:
wlan0: beacon loss from AP 00:12:17:e7:98:de - sending probe request
But in fact there is no beacon loss, the beacons are just not received
because of the ongoing scan. Fix it by updating last_beacon after
the scan has finished.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org> Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the code paths sending deauth/disassoc events ends up calling
this function with rcu_read_lock held, so we must use GFP_ATOMIC in
allocation routines.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a hang on resume when the filesystem is not
available and request_firmware blocks.
However, the device does not accept the firmware on resume.
and it will exit with:
> firmware part 1 upload failed (-71).
> device is in a bad state. please reconnect it!
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove this unused Kconfig variable, which Intel apparently once
promised to make use of but never did.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not work correctly yet, so the code does more harm than good.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 28 Mar 2009 19:51:58 +0000 (20:51 +0100)]
rt2x00: Don't free register information on suspend
After suspend & resume the rt2x00 devices won't wakeup
anymore due to a broken register information setup.
The most important problem is the release of the EEPROM
buffer which is completely cleared and never read again
after the suspend.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Herbert Xu [Sun, 19 Apr 2009 22:35:50 +0000 (22:35 +0000)]
tun: Fix sk_sleep races when attaching/detaching
As the sk_sleep wait queue actually lives in tfile, which may be
detached from the tun device, bad things will happen when we use
sk_sleep after detaching.
Since the tun device is the persistent data structure here (when
requested by the user), it makes much more sense to have the wait
queue live there. There is no reason to have it in tfile at all
since the only time we can wait is if we have a tun attached.
In fact we already have a wait queue in tun_struct, so we might
as well use it.
Reported-by: Eric W. Biederman <ebiederm@xmission.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Tested-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 18 Apr 2009 14:15:52 +0000 (14:15 +0000)]
tun: Only free a netdev when all tun descriptors are closed
The commit c70f182940f988448f3c12a209d18b1edc276e33 ("tun: Fix
races between tun_net_close and free_netdev") fixed a race where
an asynchronous deletion of a tun device can hose a poll(2) on
a tun fd attached to that device.
However, this came at the cost of moving the tun wait queue into
the tun file data structure. The problem with this is that it
imposes restrictions on when and where the tun device can access
the wait queue since the tun file may change at any time due to
detaching and reattaching.
In particular, now that we need to use the wait queue on the
receive path it becomes difficult to properly synchronise this
with the detachment of the tun device.
This patch solves the original race in a different way. Since
the race is only because the underlying memory gets freed, we
can prevent it simply by ensuring that we don't do that until
all tun descriptors ever attached to the device (even if they
have since be detached because they may still be sitting in poll)
have been closed.
This is done by using reference counting the attached tun file
descriptors. The refcount in tun->sk has been reappropriated
for this purpose since it was already being used for that, albeit
from the opposite angle.
Note that we no longer zero tfile->tun since tun_get will return
NULL anyway after the refcount on tfile hits zero. Instead it
represents whether this device has ever been attached to a device.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sat, 18 Apr 2009 05:48:48 +0000 (05:48 +0000)]
tcp: fix mid-wq adjustment helper
Just noticed while doing some new work that the recent
mid-wq adjustment logic will misbehave when FACK is not
in use (happens either due sysctl'ed off or auto-detected
reordering) because I forgot the relevant TCPCB tagbit.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sch_netem: Fix an inconsistency in ingress netem timestamps.
Alex Sidorenko reported:
"while experimenting with 'netem' we have found some strange behaviour. It
seemed that ingress delay as measured by 'ping' command shows up on some
hosts but not on others.
After some investigation I have found that the problem is that skbuff->tstamp
field value depends on whether there are any packet sniffers enabled. That
is:
- if any ptype_all handler is registered, the tstamp field is as expected
- if there are no ptype_all handlers, the tstamp field does not show the delay"
This patch prevents unnecessary update of tstamp in dev_queue_xmit_nit()
on ingress path (with act_mirred) adding a check, so minimal overhead on
the fast path, but only when sniffers etc. are active.
Since netem at ingress seems to logically emulate a network before a host,
tstamp is zeroed to trigger the update and pretend delays are from the
outside.
Reported-by: Alex Sidorenko <alexandre.sidorenko@hp.com> Tested-by: Alex Sidorenko <alexandre.sidorenko@hp.com> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Fri, 17 Apr 2009 04:19:36 +0000 (04:19 +0000)]
ax25: proc uid file misses header
This has been broken for a while. I happened to catch it testing because one
app "knew" that the top line of the calls data was the policy line and got
confused.
Put the header back.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Divy Le Ray [Fri, 17 Apr 2009 12:21:27 +0000 (12:21 +0000)]
cxgb3: Fix EEH final recovery attempt
EEH attempts to recover up 6 times.
The last attempt leaves all the ports and adapter down.hen
The driver is then unloaded, bringing the adapter down again
unconditionally. The unload will hang.
Check if the adapter is already down before trying to bring it down again.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Divy Le Ray [Fri, 17 Apr 2009 12:21:17 +0000 (12:21 +0000)]
cxgb3: fix workqueue flush issues
The fatal error task can be scheduled while processing an offload packet
in NAPI context when the connection handle is bogus. this can race
with the ports being brought down and the cxgb3 workqueue being flushed.
Stop napi processing before flushing the work queue.
The ULP drivers (iSCSI, iWARP) might also schedule a task on keventd_wk
while releasing a connection handle (cxgb3_offload.c::cxgb3_queue_tid_release()).
The driver however does not flush any work on keventd_wq while being unloaded.
This patch also fixes this.
Also call cancel_delayed_work_sync in place of the the deprecated
cancel_rearming_delayed_workqueue.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Divy Le Ray [Fri, 17 Apr 2009 12:21:11 +0000 (12:21 +0000)]
cxgb3: fix link fault handling
Use the existing periodic task to handle link faults.
The link fault interrupt handler is also called in work queue context,
which is wrong and might cause potential deadlocks.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Link Manager negotiates the fallback to SCO, but then sends out
a Connect Complete event. This is wrong and the Link Manager should
actually send a Synchronous Connection Complete event if the Setup
Synchronous Connection has been used. Only the remote side is allowed
to use Connect Complete to indicate the missing support for eSCO in
the host stack.
This patch adds a workaround for this which clearly should not be
needed, but reality is that broken Broadcom devices are deployed.
Based on a report by Ville Tervo <ville.tervo@nokia.com>
Bluetooth: Fallback from eSCO to SCO on unspecified error
Some Bluetooth chips (like the ones from Texas Instruments) don't do
proper eSCO negotiations inside the Link Manager. They just return an
error code and in case of the Kyocera ED-8800 headset it is just a
random error.
Johan Hedberg [Thu, 26 Mar 2009 14:41:56 +0000 (16:41 +0200)]
Bluetooth: Fix removing of RFCOMM DLC timer with DEFER_SETUP
There is a missing call to rfcomm_dlc_clear_timer in the case that
DEFER_SETUP is used and so the connection gets disconnected after the
timeout even if it was successfully accepted previously.
This patch adds a call to rfcomm_dlc_clear_timer to rfcomm_dlc_accept
which will get called when the user accepts the connection by calling
read() on the socket.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Patrick McHardy [Fri, 17 Apr 2009 22:59:23 +0000 (15:59 -0700)]
vlan/macvlan: fix NULL pointer dereferences in ethtool handlers
Check whether the underlying device provides a set of ethtool ops before
checking for individual handlers to avoid NULL pointer dereferences.
Reported-by: Art van Breemen <ard@telegraafnet.nl> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 16 Apr 2009 13:00:58 +0000 (15:00 +0200)]
cfg80211: do not replace BSS structs
Instead, allocate extra IE memory if necessary. Normally,
this isn't even necessary since there's enough space.
This is a better way of correcting the "held BSS can
disappear" issue, but also a lot more code. It is also
necessary for proper auth/assoc BSS handling in the
future.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 16 Apr 2009 10:15:38 +0000 (12:15 +0200)]
cfg80211: copy hold when replacing BSS
When we receive a probe response frame we can replace the
BSS struct in our list -- but if that struct is held then
we need to hold the new one as well.
We really should fix this completely and not replace the
struct, but this is a bandaid for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
netfilter: nfnetlink: return ENOMEM if we fail to create netlink socket
With this patch, nfnetlink returns -ENOMEM instead of -EPERM if we
fail to create the nfnetlink netlink socket during the module
loading. This is exactly what rtnetlink does in this case.
Ideally, it would be better if we propagate the error that has
happened in netlink_kernel_create(), however, this function still
does not implement this yet.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net>
Herbert Xu [Fri, 17 Apr 2009 09:34:38 +0000 (02:34 -0700)]
gro: Fix use after free in tcp_gro_receive
After calling skb_gro_receive skb->len can no longer be relied
on since if the skb was merged using frags, then its pages will
have been removed and the length reduced.
This caused tcp_gro_receive to prematurely end merging which
resulted in suboptimal performance with ixgbe.
The fix is to store skb->len on the stack.
Reported-by: Mark Wagner <mwagner@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Fri, 17 Apr 2009 08:38:46 +0000 (01:38 -0700)]
can: Network Drop Monitor: Make use of consume_skb() in af_can.c
Since commit ead2ceb0ec9f85cff19c43b5cdb2f8a054484431 ("Network Drop
Monitor: Adding kfree_skb_clean for non-drops and modifying
end-of-line points for skbs") so called end-of-line points for skb's
should use consume_skb() to free the socket buffer.
In opposite to consume_skb() the function kfree_skb() is intended to
be used for unexpected skb drops e.g. in error conditions that now can
trigger the network drop monitor if enabled.
This patch moves the skb end-of-line point in af_can.c to use
consume_skb().
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Waling [Wed, 15 Apr 2009 23:32:11 +0000 (23:32 +0000)]
macb: process the RX ring regardless of interrupt status
Suppose that we receive lots of frames, start processing them, but
exhaust our budget so that we return before we had a chance to look
at all of them.
Then, when the network layer calls us again, we will only continue
processing the buffers if the REC bit was set in the mean time, which it
might not be if there was a brief pause in the flow of packets. If this
happens, we'll simply display a warning and call netif_rx_complete()
with potentially lots of unprocessed packets in the RX ring...
Fix this by scanning the ring no matter what flags are set in the
interrupt status register.
Signed-off-by: Erik Waling <erik.waling@konftel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Waling [Wed, 15 Apr 2009 23:32:10 +0000 (23:32 +0000)]
macb: Handle Retry Limit Exceeded errors
When transfering large amounts of data we sometimes experienced that the
Retry Limit Exceeded (RLE) bit got set in TSR during transmission
attempts. When this happened the driver would stall in a state that
prevented any more data from being sent.
Signed-off-by: Erik Waling <erik.waling@konftel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The thresholds for the DCB priority flow control are incorrect for 82599.
This fixes the thresholds to be correct.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The traffic classes in hardware are not symmetrical for Rx and Tx. Rx
is every 16 descriptor queues, Tx is not. It runs 32-32-16-16-8-8-8 when
running with 8 traffic classes, and runs 64-32-16 when running with 4
traffic classes. This patch fixes the mapping.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Cc: stable@kernel.org Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000 transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000e transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Breeds [Thu, 16 Apr 2009 23:27:23 +0000 (16:27 -0700)]
ixgbe: Be explict with what we are !'ing in ixgbe_sfp_config_module_task()
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 16 Apr 2009 16:33:01 +0000 (18:33 +0200)]
netfilter: nf_nat: add support for persistent mappings
The removal of the SAME target accidentally removed one feature that is
not available from the normal NAT targets so far, having multi-range
mappings that use the same mapping for each connection from a single
client. The current behaviour is to choose the address from the range
based on source and destination IP, which breaks when communicating
with sites having multiple addresses that require all connections to
originate from the same IP address.
Introduce a IP_NAT_RANGE_PERSISTENT option that controls whether the
destination address is taken into account for selecting addresses.
Johannes Berg [Fri, 10 Apr 2009 08:02:45 +0000 (10:02 +0200)]
ar9170: fix struct layout on arm
arm will pad even between u8's, so mark the structs/unions
packed. Fixes a build bug on arm due to BUILD_BUG_ON tests
in the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Fri, 10 Apr 2009 01:41:05 +0000 (21:41 -0400)]
orinoco: correct timeout logic in __orinoco_hw_set_tkip_key()
If the value read from HERMES_RID_TXQUEUEEMPTY becomes 0 after exactly
100 readings, we wrongly consider it a timeout. Rewrite the clever
while loop as a for loop that does the right thing and looks simpler.
Reported by Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_ioctl_siwfrag() sets the fragmentation_threshold to 2352
when frame fragmentation is to be disabled, yet the corresponding
'get' function tests for 2353 bytes instead.
This causes user-space tools to display a fragmentation threshold
of 2352 bytes even if fragmentation has been disabled.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: prevent double kfree when failing to register hardware
In a scenario where there isn't any firmware available, we will have a
double kfree of rt2x00dev->spec.channels_info when ieee80211_register_hw
returns an error status inside rt2x00lib_probe_hw.
The problem is that if ieee80211_register_hw fails, we call
rt2x00lib_remove_hw twice:
* first inside rt2x00lib_probe_hw upon failure of ieee80211_register_hw
* error status is returned to rt2x00lib_probe_dev, which then sees it and
calls in this case rt2x00lib_remove_dev that will again run
rt2x00lib_remove_hw
Prevent this avoiding calling rt2x00lib_remove_hw inside
rt2x00lib_probe_hw
Problem was detected with CONFIG_DEBUG_PAGEALLOC=y, CONFIG_SLUB_DEBUG=y,
CONFIG_SLUB_DEBUG_ON=y, that dumps this with no firmware available:
rt61pci 0000:00:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
wmaster0 (rt61pci): not using net_device_ops yet
phy0: Selected rate control algorithm 'pid'
phy0: Failed to initialize wep: -2
phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw.
=============================================================================
BUG kmalloc-128: Object already free
-----------------------------------------------------------------------------
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Wed, 15 Apr 2009 18:41:22 +0000 (14:41 -0400)]
mac80211: quiet beacon loss messages
On Sunday 05 April 2009 11:29:38 Michael Buesch wrote:
> On Sunday 05 April 2009 11:23:59 Jaswinder Singh Rajput wrote:
> > With latest linus tree I am getting, .config file attached:
> >
> > [ 22.895051] r8169: eth0: link down
> > [ 22.897564] ADDRCONF(NETDEV_UP): eth0: link is not ready
> > [ 22.928047] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> > [ 22.982292] libvirtd used greatest stack depth: 4200 bytes left
> > [ 63.709879] wlan0: authenticate with AP 00:11:95:9e:df:f6
> > [ 63.712096] wlan0: authenticated
> > [ 63.712127] wlan0: associate with AP 00:11:95:9e:df:f6
> > [ 63.726831] wlan0: RX AssocResp from 00:11:95:9e:df:f6 (capab=0x471 status=0 aid=1)
> > [ 63.726855] wlan0: associated
> > [ 63.730093] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> > [ 74.296087] wlan0: no IPv6 routers present
> > [ 79.349044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 119.358200] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 179.354292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 259.366044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 359.348292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 361.953459] packagekitd used greatest stack depth: 4160 bytes left
> > [ 478.824258] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 598.813343] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 718.817292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 838.824567] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 958.815402] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1078.848434] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1198.822913] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1318.824931] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1438.814157] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1558.827336] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1678.823011] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1798.830589] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1918.828044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2038.827224] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2116.517152] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2158.840243] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2278.827427] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
>
>
> I think this message should only show if CONFIG_MAC80211_VERBOSE_DEBUG is set.
> It's kind of expected that we lose a beacon once in a while, so we shouldn't print
> verbose messages to the kernel log (even if they are KERN_DEBUG).
>
> And besides that, I think one can easily remotely trigger this message and flood the logs.
> So it should probably _also_ be ratelimited.
Reported-by: Mike Kershaw/Dragorn <dragorn@kismetwireless.net> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Wed, 8 Apr 2009 14:15:17 +0000 (10:15 -0400)]
airo: queue SIOCSIWAUTH-requested auth mode change for next commit
Code was clearly wrong, plus callers expect the mode change to happen as
soon as possible, not dropped on the floor until the next time some
other config value changes and a commit happens.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 7 Apr 2009 13:22:28 +0000 (15:22 +0200)]
mac80211: correct wext transmit power handler
Wext makes no assumptions about the contents of
data->txpower.fixed and data->txpower.value when
data->txpower.disabled is set, so do not update
the user-requested power level while disabling.
Also, when wext configures a really _fixed_ power
output [1], we should reject it instead of limiting it
to the regulatory constraint. If the user wants to set
a _limit_ [2] then we should honour that.
This patch fixes the following waring:
> ------------[ cut here ]------------
>WARNING: at kernel/softirq.c:138 local_bh_enable+0x54/0xbc()
>Modules linked in: p54spi
>[<c0034ff8>] (dump_stack+0x0/0x14)
>[<c005b1a4>] (warn_on_slowpath+0x0/0x68)
>[<c00604c8>] (local_bh_enable+0x0/0xbc)
>[<bf000000>] (p54spi_op_tx+0x0/0x4c [p54spi])
>[<c01a4d34>] (p54_sta_unlock+0x0/0x78)
p54spi_op_tx needs to be called from different locking contexts.
Therefore we have to protect the linked list with irqsave spinlocks.
Reported-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm very sorry, as this change belongs to the other patch:
"[PATCH] p54: fix SoftLED compile dependencies".
however I must have somehow lost "git add" for that file.
Signed-off-by: Christian Lamparter <chunkeey@web.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Fri, 27 Mar 2009 23:41:25 +0000 (00:41 +0100)]
b43: Refresh RX poison on buffer recycling
The RX buffer poison needs to be refreshed, if we recycle an RX buffer,
because it might be (partially) overwritten by some DMA operations.
Cc: stable@kernel.org Cc: Francesco Gringoli <francesco.gringoli@ing.unibs.it> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Fri, 27 Mar 2009 21:51:58 +0000 (22:51 +0100)]
b43: Poison RX buffers
This patch adds poisoning and sanity checking to the RX DMA buffers.
This is used for protection against buggy hardware/firmware that raises
RX interrupts without doing an actual DMA transfer.
This mechanism protects against rare "bad packets" (due to uninitialized skb data)
and rare kernel crashes due to uninitialized RX headers.
The poison is selected to not match on valid frames and to be cheap for checking.
The poison check mechanism _might_ trigger incorrectly, if we are voluntarily
receiving frames with bad PLCP headers. However, this is nonfatal, because the
chance of such a match is basically zero and in case it happens it just results
in dropping the packet.
Bad-PLCP RX defaults to off, and you should leave it off unless you want to listen
to the latest news broadcasted by your microwave oven.
This patch also moves the initialization of the RX-header "length" field in front of
the mapping of the DMA buffer. The CPU should not touch the buffer after we mapped it.
Cc: stable@kernel.org Reported-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Fix bug in getting rx status for frames pending in reorder buffer
Currently rx status for frames which are completed from reorder buffer
is taken from it's cb area which is not always right, cb is not holding
the rx status when driver uses mac80211's non-irq rx handler to pass it's
received frames. This results in dropping almost all frames from reorder
buffer when security is enabled by doing double decryption (first in hw,
second in sw because of wrong rx status). This patch copies rx status into
cb area before the frame is put into reorder buffer. After this patch,
there is a significant improvement in throughput with ath9k + WPA2(AES).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211: fix NULL pointer deference in reg_device_remove()
We won't ever get here as regulatory_hint_core() can only fail
on -ENOMEM and in that case we don't initialize cfg80211 but this is
technically correct code.
This is actually good for stable, where we don't check for -ENOMEM
failure on __regulatory_hint()'s failure.
Cc: stable@kernel.org Reported-by: Quentin Armitage <Quentin@armitage.org.uk> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
phylib: Fix delay argument of schedule_delayed_work
The commit a390d1f3 ("phylib: convert state_queue work to
delayed_work") missed converting 'expires' value to 'delay' value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Acked-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent ixgbe from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate ixgbe_shutdown() from ixgbe_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000e from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000e_shutdown() from e1000e_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000 from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000_shutdown() from e1000_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 15 Apr 2009 10:45:08 +0000 (12:45 +0200)]
netfilter: nf_conntrack: fix crash when unloading helpers
Commit ea781f197d (netfilter: nf_conntrack: use SLAB_DESTROY_BY_RCU and)
get rid of call_rcu() was missing one conversion to the hlist_nulls
functions, causing a crash when unloading conntrack helper modules.
Reported-and-tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Patrick McHardy <kaber@trash.net>
Eric Dumazet [Wed, 15 Apr 2009 10:16:19 +0000 (12:16 +0200)]
netfilter: nf_log regression fix
commit ca735b3aaa945626ba65a3e51145bfe4ecd9e222
'netfilter: use a linked list of loggers'
introduced an array of list_head in "struct nf_logger", but
forgot to initialize it in nf_log_register(). This resulted
in oops when calling nf_log_unregister() at module unload time.
Reported-and-tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Acked-by: Eric Leblond <eric@inl.fr> Signed-off-by: Patrick McHardy <kaber@trash.net>
Markus Brunner [Wed, 15 Apr 2009 09:35:40 +0000 (02:35 -0700)]
gianfar: stop send queue before resetting gianfar
After a transmit timed out, the reset task will be called, which will free the
allocated resources(stop_gfar). If gfar_poll will be called before the
resources get allocated again gfar_clean_tx_ring will call
dev_kfree_skb_any(NULL).
ixgbe: update real_num_tx_queues on changing num_rx_queues
Move the update of real_num_tx_queues from
ixgbe_acquire_msix_vectors() to ixgbe_set_num_queues(), to ensure it
be always in sync with num_tx_queues.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don't do the num_tx_queues based masking on calculating tx queue
index.
1) num_tx_queues is not always power-of-2, because it also depends on
the online cpu numbers. So the masking could be a performance bug
on a 6 cpu system.
2) queue_mapping will be limited by real_num_tx_queues=num_tx_queues
in the generic netdev function set_cur_queue_map(). So the bound
limiting here is not necessary.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>