The processor is documented to reload the PDPTRs while in PAE mode if any
of the CR4 bits PSE, PGE, or PAE change. Linux relies on this
behaviour when zapping the low mappings of PAE kernels during boot.
The code already handled changes to CR4.PAE; augment it to also notice changes
to PSE and PGE.
This triggered while booting an F11 PAE kernel; the futex initialization code
runs before any CR3 reloads and writes to a NULL pointer; the futex subsystem
ended up uninitialized, killing PI futexes and pulseaudio which uses them.
Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The paravirt tlb flush may be used not only to flush TLBs, but also
to reload the four page-directory-pointer-table entries, as it is used
as a replacement for reloading CR3. Change the code to do the entire
CR3 reloading dance instead of simply flushing the TLB.
Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
KVM optimizes guest port 80 accesses by passthing them through to the host.
Some AMD machines die on port 80 writes, allowing the guest to hard-lock the
host.
Remove the port passthrough to avoid the problem.
Reported-by: Piotr Jaroszyński <p.jaroszynski@gmail.com> Tested-by: Piotr Jaroszyński <p.jaroszynski@gmail.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vmx_set_msr() does not allow i386 guests to touch EFER, but they can still
do so through the default: label in the switch. If they set EFER_LME, they
can oops the host.
Fix by having EFER access through the normal channel (which will check for
EFER_LME) even on i386.
Reported-and-tested-by: Benjamin Gilbert <bgilbert@cs.cmu.edu> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One of vcpu_setup responsibilities is to do mmu initialization.
However, in case we fail in kvm_arch_vcpu_reset, before we get the
chance to init mmu. OTOH, vcpu_destroy will attempt to destroy mmu,
triggering a bug. Keeping track of whether or not mmu is initialized
would unnecessarily complicate things. Rather, we just make return,
making sure any needed uninitialization is done before we return, in
case we fail.
Signed-off-by: Glauber Costa <glommer@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a potential issue that, when guest using pagetable without vmexit when
EPT enabled, guest would use PAT/PCD/PWT bits to index PAT msr for it's memory,
which would be inconsistent with host side and would cause host MCE due to
inconsistent cache attribute.
The patch set IGMT bit in EPT entry to ignore guest PAT and use WB as default
memory type to protect host (notice that all memory mapped by KVM should be WB).
Signed-off-by: Sheng Yang <sheng@linux.intel.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The page fault path can use two rmap_desc structures, if:
- walk_addr's dirty pte update allocates one rmap_desc.
- mmu_lock is dropped, sptes are zapped resulting in rmap_desc being
freed.
- fetch->mmu_set_spte allocates another rmap_desc.
Currently KVM implements MC0-MC4_MISC read support. When booting Linux this
results in KVM warnings in the kernel log when the guest tries to read
MC5_MISC. Fix this warnings with this patch.
We're in a hot path. We can't use kmalloc() because
it might impact performance. So, we just stick the buffer that
we need into the kvm_vcpu_arch structure. This is used very
often, so it is not really a waste.
We also have to move the buffer structure's definition to the
arch-specific x86 kvm header.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On my machine with gcc 3.4, kvm uses ~2k of stack in a few
select functions. This is mostly because gcc fails to
notice that the different case: statements could have their
stack usage combined. It overflows very nicely if interrupts
happen during one of these large uses.
This patch uses two methods for reducing stack usage.
1. dynamically allocate large objects instead of putting
on the stack.
2. Use a union{} member for all of the case variables. This
tricks gcc into combining them all into a single stack
allocation. (There's also a comment on this)
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The accessed bit was accidentally turned on in a random flag word, rather
than, the spte itself, which was lucky, since it used the non-EPT compatible
PT_ACCESSED_MASK.
Fix by turning the bit on in the spte and changing it to use the portable
accessed mask.
Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is esoteric and only needed to break COW on MAP_SHARED mappings. Since
KVM no longer does these sorts of mappings, breaking COW on them is no longer
necessary.
Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the bug that was reported in
http://bugzilla.kernel.org/show_bug.cgi?id=14053
If we're in the case where we need to force a reencode and then resend of
the RPC request, due to xprt_transmit failing with a networking error, then
we _must_ retransmit the entire request.
snd_interval_list() expected a sorted list but did not document this, so
there are drivers that give it an unsorted list. To fix this, change
the algorithm to work with any list.
This fixes the "Slave PCM not usable" error with USB devices that have
multiple alternate settings with sample rates in decreasing order, such
as the Philips Askey VC010 WebCam.
http://bugzilla.kernel.org/show_bug.cgi?id=14028
Reported-and-tested-by: Andrzej <adkadk@gmail.com> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the napi list handling when an ehea interface is shut
down to avoid corruption of the napi list.
Signed-off-by: Hannes Hering <hering2@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
do {
ret = waitpid(pid, &status, 0);
} while (ret == -1 && errno == EINTR);
}
return 0;
}
quickly creates an unkillable task.
If copy_process(CLONE_THREAD) races with de_thread()
copy_signal()->atomic(signal->count) breaks the signal->notify_count
logic, and the execing thread can hang forever in kernel space.
Change copy_process() to increment count/live only when we know for sure
we can't fail. In this case the forked thread will take care of its
reference to signal correctly.
If copy_process() fails, check CLONE_THREAD flag. If it it set - do
nothing, the counters were not changed and current belongs to the same
thread group. If it is not set, ->signal must be released in any case
(and ->count must be == 1), the forked child is the only thread in the
thread group.
We need more cleanups here, in particular signal->count should not be used
by de_thread/__exit_signal at all. This patch only fixes the bug.
This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.
We can't call nfs_readdata_release()/nfs_writedata_release() without
first initialising and referencing args.context. Doing so inside
nfs_direct_read_schedule_segment()/nfs_direct_write_schedule_segment()
causes an Oops.
We should rather be calling nfs_readdata_free()/nfs_writedata_free() in
those cases.
Looking at the O_DIRECT code, the "struct nfs_direct_req" is already
referencing the nfs_open_context for us. Since the readdata and writedata
structures carry a reference to that, we can simplify things by getting rid
of the extra nfs_open_context references, so that we can replace all
instances of nfs_readdata_release()/nfs_writedata_release().
kernel_sendpage() does the proper default case handling for when the
socket doesn't have a native sendpage implementation.
Now, arguably this might be something that we could instead solve by
just specifying that all protocols should do it themselves at the
protocol level, but we really only care about the common protocols.
Does anybody really care about sendpage on something like Appletalk? Not
likely.
Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Julien TINNES <julien@cr0.org> Acked-by: Tavis Ormandy <taviso@sdf.lonestar.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mm_for_maps() takes ->mmap_sem after security checks, this looks
strange and obfuscates the locking rules. Move this lock to its
single caller, m_start().
It would be nice to kill __ptrace_may_access(). It requires task_lock(),
but this lock is only needed to read mm->flags in the middle.
Convert mm_for_maps() to use ptrace_may_access(), this also simplifies
the code a little bit.
Also, we do not need to take ->mmap_sem in advance. In fact I think
mm_for_maps() should not play with ->mmap_sem at all, the caller should
take this lock.
With or without this patch, without ->cred_guard_mutex held we can race
with exec() and get the new ->mm but check old creds.
This patch (as1272) changes the error code returned when an open call
for a USB device node fails to locate the corresponding device. The
appropriate error code is -ENODEV, not -ENOENT.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached patch adds USB vendor and product IDs for Bayer's USB to serial
converter cable used by Bayer blood glucose meters. It seems to be a
FT232RL based device and works without any problem with ftdi_sio driver
when this patch is applied. See: http://winglucofacts.com/cables/
Signed-off-by: Marko Hänninen <bugitus@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
access_ok() checks must be done on every part of the userspace structure
that is accessed. If access_ok() on one part of the struct succeeded, it
does not imply it will succeed on other parts of the struct. (Does
depend on the architecture implementation of access_ok()).
This changes the __get_user() users to first check access_ok() on the
data structure.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While looking at Jens Rosenboom bug report
(http://lkml.org/lkml/2009/7/27/35) about strange sys_futex call done from
a dying "ps" program, we found following problem.
clone() syscall has special support for TID of created threads. This
support includes two features.
One (CLONE_CHILD_SETTID) is to set an integer into user memory with the
TID value.
One (CLONE_CHILD_CLEARTID) is to clear this same integer once the created
thread dies.
The integer location is a user provided pointer, provided at clone()
time.
kernel keeps this pointer value into current->clear_child_tid.
At execve() time, we should make sure kernel doesnt keep this user
provided pointer, as full user memory is replaced by a new one.
As glibc fork() actually uses clone() syscall with CLONE_CHILD_SETTID and
CLONE_CHILD_CLEARTID set, chances are high that we might corrupt user
memory in forked processes.
Following sequence could happen:
1) bash (or any program) starts a new process, by a fork() call that
glibc maps to a clone( ... CLONE_CHILD_SETTID | CLONE_CHILD_CLEARTID
...) syscall
2) When new process starts, its current->clear_child_tid is set to a
location that has a meaning only in bash (or initial program) context
(&THREAD_SELF->tid)
3) This new process does the execve() syscall to start a new program.
current->clear_child_tid is left unchanged (a non NULL value)
4) If this new program creates some threads, and initial thread exits,
kernel will attempt to clear the integer pointed by
current->clear_child_tid from mm_release() :
/*
* We don't check the error code - if userspace has
* not set up a proper pointer then tough luck.
*/
<< here >> put_user(0, tidptr);
sys_futex(tidptr, FUTEX_WAKE, 1, NULL, NULL, 0);
}
5) OR : if new program is not multi-threaded, but spied by /proc/pid
users (ps command for example), mm_users > 1, and the exiting program
could corrupt 4 bytes in a persistent memory area (shm or memory mapped
file)
If current->clear_child_tid points to a writeable portion of memory of the
new program, kernel happily and silently corrupts 4 bytes of memory, with
unexpected effects.
Fix is straightforward and should not break any sane program.
The FIEMAP_IOC_FIEMAP mapping ioctl was missing a 32-bit compat handler,
which means that 32-bit suerspace on 64-bit kernels cannot use this ioctl
command.
The structure is nicely aligned, padded, and sized, so it is just this
simple.
Tested w/ 32-bit ioctl tester (from Josef) on a 64-bit kernel on ext4.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Cc: <linux-ext4@vger.kernel.org> Cc: Mark Lord <lkml@rtr.ca> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Josef Bacik <josef@redhat.com> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds two new device ids to the asix driver.
One comes directly from the asix driver on their web site, the other was
reported by Armani Liao as needed for the MSI X320 to get the driver to
work properly for it.
Reported-by: Armani Liao <aliao@novell.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The current code to set up the GART as an IOMMU enables GART
translations before it removes the aperture from the kernel memory
map, sets the GART PTEs to UC, sets up the guard and scratch
pages, or does a wbinvd(). This leaves the possibility of cache
aliasing open and can cause system crashes.
Re-order the code so as to enable the GART translations only
after all safeguards are in place and the tlb has been flushed.
AMD has tested this patch on both Istanbul systems and 1st
generation Opteron systems with APG enabled and seen no adverse
effects. Istanbul systems with HT Assist enabled sometimes
see MCE errors due to cache artifacts with the unmodified
code.
Increase the command ORB data structure to transport up to 16 bytes long
CDBs (instead of 12 bytes), and tell the SCSI mid layer about it. This
is notably necessary for READ CAPACITY(16) and friends, i.e. support of
large disks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the command ORB data structure to transport up to 16 bytes long
CDBs (instead of 12 bytes), and tell the SCSI mid layer about it. This
is notably necessary for READ CAPACITY(16) and friends, i.e. support of
large disks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
parisc: ensure broadcast tlb purge runs single threaded
The TLB flushing functions on hppa, which causes PxTLB broadcasts on the system
bus, needs to be protected by irq-safe spinlocks to avoid irq handlers to deadlock
the kernel. The deadlocks only happened during I/O intensive loads and triggered
pretty seldom, which is why this bug went so long unnoticed.
Signed-off-by: Helge Deller <deller@gmx.de>
[edited to use spin_lock_irqsave on UP as well since we'd been locking there
all this time anyway, --kyle] Signed-off-by: Kyle McMartin <kyle@mcmartin.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
11static inline unsigned long native_save_fl(void)
12{
13 unsigned long flags;
14
15 asm volatile("# __raw_save_flags\n\t"
16 "pushf ; pop %0"
17 : "=g" (flags)
18 : /* no input */
19 : "memory");
20
21 return flags;
22}
If gcc chooses to put flags on the stack, for instance because this is
inlined into a larger function with more register pressure, the offset
of the flags variable from the stack pointer will change when the
pushf is performed. gcc doesn't attempt to understand that fact, and
address used for pop will still be the same. It will write to
somewhere near flags on the stack but not actually into it and
overwrite some other value.
I saw this happen in the ide_device_add_all function when running in a
simulator I work on. I'm assuming that some quirk of how the simulated
hardware is set up caused the code path this is on to be executed when
it normally wouldn't.
A simple fix might be to change "=g" to "=r".
Reported-by: Gabe Black <spamforgabe@umich.edu> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Requests to get max LUN, for certain USB storage devices, require a
longer timeout before a correct reply is returned. This happens for a
Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set
to 0, thus losing functionality, because of the timeout occurring too
quickly.
Raising the timeout value fixes the issue and might help other devices
to return a correct max LUN value as well.
Currently, the ThinkPad-ACPI bay and dock drivers are completely
broken, and cause a NULL pointer derreference in kernel mode (and,
therefore, an OOPS) when they try to issue events (i.e. on dock,
undock, bay ejection, etc).
OTOH, the standard ACPI dock driver can handle the hotplug bays and
docks of the ThinkPads just fine (including batteries) as of 2.6.27.
In fact, it does a much better job of it than thinkpad-acpi ever did.
It is just not worth the hassle to find a way to fix this crap without
breaking the (deprecated) thinkpad-acpi dock/bay ABI. This is old,
deprecated code that sees little testing or use.
As a quick fix suitable for -stable backports, mark the thinkpad-acpi
bay and dock subdrivers as BROKEN in Kconfig. The dead code will be
removed by a later patch.
This fixes bugzilla #13669, and should be applied to 2.6.27 and later.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Reported-by: Joerg Platte <jplatte@naasa.net> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update directory hardlink count when moving kobjects to a new parent.
Fixes the following problem which occurs when several devices are
moved to the same parent and then unregistered:
Narayanan reports "The regression is around 15%. There is no disk controller
as our setup is based on Samsung OneNAND used as a memory mapped device on a
OMAP2430 based board."
The page allocator tries to preserve contiguous PFN ordering when returning
pages such that repeated callers to the allocator have a strong chance of
getting physically contiguous pages, particularly when external fragmentation
is low. However, of the bulk of the allocations have __GFP_COLD set as they
are due to aio_read() for example, then the PFNs are in reverse PFN order.
This can cause performance degration when used with IO controllers that could
have merged the requests.
This patch attempts to preserve the contiguous ordering of PFNs for users of
__GFP_COLD.
There's a hotplug problem in the way libsas allocates ports: it loops over the
available ports first trying to add to an existing for a wide port and
otherwise allocating the next free port. This scheme only works if the port
array is packed from zero, which fails if a port gets hot unplugged and the
array becomes sparse. In that case, a new port is formed even if there's a
wide port it should be part of. Fix this by creating two loops over all the
ports: the first to see if the phy should be part of a wide port and the
second to form a new port in an empty port slot.
Signed-off-by: Tom Peng <tom_peng@usish.com> Signed-off-by: Jack Wang <jack_wang@usish.com> Signed-off-by: Lindar Liu <lindar_liu@usish.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've tested TSL2550 driver and I've found a bug: when light is off,
returned value from tsl2550_calculate_lux function is -1 when it should
be 0 (sensor correctly read that light was off).
I think the bug is that a zero c0 value (approximated value of ch0) is
misinterpreted as an error.
Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com> Acked-by: Rodolfo Giometti <giometti@linux.it> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is because hugetlb_unreserve_pages() is unconditionally removing
blocks_per_huge_page(h) on each call rather than using the freed amount.
If there were 0 blocks, it goes negative, resulting in the above.
The issue was, that the locking code in mkiss was assuming it was only
ever being called in process or bh context. Fixed by converting the
involved locking code to use irq-safe locks.
Review of other networking line disciplines shows that 6pack, both sync
and async PPP and STRIP have similar issues. The ppp_async one is the
most interesting one as it sorts out half of the issue as far back as
2004 in commit http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=2996d8deaeddd01820691a872550dc0cfba0c37d
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Reported-by: Guido Trentalancia <guido@trentalancia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Unfortunately it fails to
transfer skb->data ownership to the device after it reads the
descriptor's status, breaking on non-coherent (e.g., ARM) platforms.
This have to be converted to use coherent memory for the descriptors.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 8169 chip only generates MSI interrupts when all enabled event
sources are quiescent and one or more sources transition to active. If
not all of the active events are acknowledged, or a new event becomes
active while the existing ones are cleared in the handler, we will not
see a new interrupt.
The current interrupt handler masks off the Rx and Tx events once the
NAPI handler has been scheduled, which opens a race window in which we
can get another Rx or Tx event and never ACK'ing it, stopping all
activity until the link is reset (ifconfig down/up). Fix this by always
ACK'ing all event sources, and loop in the handler until we have all
sources quiescent.
Signed-off-by: David Dillow <dave@thedillows.org> Tested-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The host-side CDC subset driver is binding more specifically
than it should ... only to PXA 210/25x/26x Linux-USB gadgets.
Loosen that restriction to match the gadget driver driver.
This will various PXA 27x and PXA 3xx devices happier when
talking to Linux hosts, potentially others.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Tested-by: Aric D. Blumer <aric@sdgsystems.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converting checksum field from le16 to CPU byte order fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Our CAST algorithm is called cast5, not cast128. Clearly nobody
has ever used it :)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tag 11 packets are stored in the metadata section of an eCryptfs file to
store the key signature(s) used to encrypt the file encryption key.
After extracting the packet length field to determine the key signature
length, a check is not performed to see if the length would exceed the
key signature buffer size that was passed into parse_tag_11_packet().
Thanks to Ramon de Carvalho Valle for finding this bug using fsfuzzer.
This patch adds DMI information to automatically load the correct
layout for the Maxdata Pro 7000X/DX notebook models. Such notebooks
are clones of Fujitsu Amilo V2000, the hook for the v2000 is being
used and I have tested that perfectly works.
The immediate result of integrating this patch is that the five
special buttons will work on these specific notebook models and that
the RF killswitch will not be activated after suspend. This patch
definitively obsoletes the fsam7400 module which I was still needing
to enable wifi and to fix the RF killswitch suspend problem; in the
current 2.6.30 kernel it is necessary to load the wistron_btns module
with options 'force=1 keymap=1557/MS2141', which was not anyway a
complete workaround.
added a call to acpi_bus_set_power(handle, ACPI_STATE_D3)
to pnpacpi_disable_resource() before the existing call
to evaluate _DIS on the device.
This caused suspend to fail on the system in
http://bugzilla.kernel.org/show_bug.cgi?id=13243
because the sanity check to verify we entered _PS3
failed on the serial port.
As a work-around, that sanity check can be disabled
system-wide with "acpi.power_nocheck=1"
Or perhaps we should just shrug off the _PS3 failure
and carry on with _DIS like we used to -- which is
what this patch does.
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(This is an update to the patch presented earlier in
http://lkml.org/lkml/2008/12/8/284, with new error handling.)
This patch sets the power of PnP ACPI devices to D0 when they
are activated and to D3 when they are disabled. The latter is
in correspondence with the ACPI 3.0 specification, whereas the
former is added in order to be able to power up a device after
it has been previously disabled (or when booting up a system).
(As a consequence, the patch makes the PnP ACPI code more ACPI
compliant.)
Section 6.2.2 of the ACPI Specification (at least versions 1.0b
and 3.0a) states: "Prior to running this control method [_DIS],
the OS[PM] will have already put the device in the D3 state."
Unfortunately, there is no clear statement as to when to put
a device in the D0 state. :-( Therefore, the patch executes the
method calls as _PS3/_DIS and _SRS/_PS0. What is clear: "If the
device is disabled, _SRS enables the device at the specified
resources." (From the ACPI 3.0a Specification.)
The patch fixes a problem with some IBM ThinkPads (at least the
600E and the 600X) where the serial ports have a dedicated
power source that needs to be brought up before the serial port
can be used. Without this patch, the serial port is enabled
but has no power. (In the past, the tpctl utility had to be
utilized to turn on the power, but support for this feature
stopped with version 5.9 as it did not support the more recent
kernel versions.)
The error handlers that handle any errors that can occur during
the power up/power down phases return the error codes to the
caller directly. Comments welcome! :-)
No regressions were observed on hardware that does not require
this patch.
The patch is applied against 2.6.27.x.
Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net> Acked-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
...so that we can distinguish between when we need to shutdown and when we
don't. Also remove the call to xs_tcp_shutdown() from xs_tcp_connect(),
since xprt_connect() makes the same test.
If the socket is unconnected, and xprt_transmit() returns ENOTCONN, we
currently give up the lock on the transport channel. Doing so means that
the lock automatically gets assigned to the next task in the xprt->sending
queue, and so that task needs to be woken up to do the actual connect.
The following patch aims to avoid that unnecessary task switch.
It's really not right to use 'access_ok()', since that is meant for the
normal "get_user()" and "copy_from/to_user()" accesses, which are done
through the TLB, rather than through the page tables.
Why? access_ok() does both too few, and too many checks. Too many,
because it is meant for regular kernel accesses that will not honor the
'user' bit in the page tables, and because it honors the USER_DS vs
KERNEL_DS distinction that we shouldn't care about in GUP. And too few,
because it doesn't do the 'canonical' check on the address on x86-64,
since the TLB will do that for us.
So instead of using a function that isn't meant for this, and does
something else and much more complicated, just do the real rules: we
don't want the range to overflow, and on x86-64, we want it to be a
canonical low address (on 32-bit, all addresses are canonical).
Acked-by: Ingo Molnar <mingo@elte.hu> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In testing a backport of the write_begin/write_end AOPs, a 10% re-read
regression was noticed when running iozone. This regression was
introduced because the old AOPs would always do a mark_page_accessed(page)
after the commit_write, but when the new AOPs where introduced, the only
place this was kept was in pagecache_write_end().
This patch does the same thing in the generic case as what is done in
pagecache_write_end(), which is just to mark the page accessed before we
do write_end().
Signed-off-by: Josef Bacik <jbacik@redhat.com> Acked-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The capture buffer size with 64kB seems broken with CA0106.
At least, either the update timing or the DMA position is wrong,
and this screws up pulseaudio badly.
This patch restricts the max buffer size less than that to make life
a bit easier.
commit 1a1fab513734b3a4fca1bee8229e5ff7e1cb873c accidentally added the
device id to both tables in the driver, which causes problems as this is
only a single port device, not a multiple port device.
The reworked Ethernet gadget has an RNDIS interop problem when used
with the CDC subset driver ... e.g. on PXA 2xx and 3xx hardware,
which currently has a hard time talking to MS-Windows hosts.
The issue is that Microsoft requires USB_CLASS_COMM. Fix by tweaking
the CDC subset driver to not switch to USB_CLASS_VENDOR_SPEC if RNDIS
is used in some other device configuration.
[ UPDATED: some "statements" were comma-terminated; fix that. ]
This patch (as1262) fixes a bug in usbfs: It refuses to accept
zero-length transfers, and it insists that the buffer pointer be valid
even if there is no data being transferred.
The patch also consolidates a bunch of repetitive access_ok() checks
into a single check, which incidentally fixes the lack of such a check
for Isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1259b) makes ehci-hcd return the total number of bytes
transferred in urb->actual_length for Isochronous transfers.
Until now, the actual_length value was unaccountably left at 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Blue Microphones USB devices have an alternate setting that sends two
channels of data to the computer. Unfortunately, the descriptors of
that altsetting have a wrong channel setting, which means that any
recorded data from such a device has twice the sample rate from what
would be expected.
This patch adds a workaround to ignore that altsetting. Since these
devices have only one actual channel, no data is lost.
I recently discovered on my zalon that if the attachment fails because
of a bus misconfiguration (I scrapped my HVD array, so the card is now
unterminated) then the system oopses. The reason is that if
ncr_attach() returns NULL (signalling failure) that NULL is passed by
the goto failed straight into ncr_detach() which oopses.
The fix is just to return -ENODEV in this case.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ISDN connection setup failed if the "connection active" and
"B channel up" messages from the device arrived in a different
order than expected. Modify the state machine to accept them in
any order.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jesper noted that kmem_cache_destroy() invokes synchronize_rcu() rather than
rcu_barrier() in the SLAB_DESTROY_BY_RCU case, which could result in RCU
callbacks accessing a kmem_cache after it had been destroyed.
Acked-by: Matt Mackall <mpm@selenic.com> Reported-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's some odd bug in gcc-4.2 where it miscompiles a simple loop whent
he loop counter is of type 'unsigned char' and it should count to 128.
The compiler will incorrectly decide that a trivial loop like this:
unsigned char i, ...
for (i = 0; i < 128; i++) {
..
is endless, and will compile it to a single instruction that just
branches to itself.
This was triggered by the addition of '-fno-strict-overflow', and we
could play games with compiler versions and go back to '-fwrapv'
instead, but the trivial way to avoid it is to just make the loop
induction variable be an 'int' instead.
Thanks to Krzysztof Oledzki for reporting and testing and to Troy Moure
for digging through assembler differences and finding it.
Reported-and-tested-by: Krzysztof Oledzki <olel@ans.pl> Found-by: Troy Moure <twmoure@szypr.net> Gcc-bug-acked-by: Ian Lance Taylor <iant@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>