Ryan Kuester [Mon, 26 Apr 2010 23:11:54 +0000 (18:11 -0500)]
[SCSI] mptsas: fix hangs caused by ATA pass-through
I may have an explanation for the LSI 1068 HBA hangs provoked by ATA
pass-through commands, in particular by smartctl.
First, my version of the symptoms. On an LSI SAS1068E B3 HBA running
01.29.00.00 firmware, with SATA disks, and with smartd running, I'm seeing
occasional task, bus, and host resets, some of which lead to hard faults of
the HBA requiring a reboot. Abusively looping the smartctl command,
# while true; do smartctl -a /dev/sdb > /dev/null; done
dramatically increases the frequency of these failures to nearly one per
minute. A high IO load through the HBA while looping smartctl seems to
improve the chance of a full scsi host reset or a non-recoverable hang.
I reduced what smartctl was doing down to a simple test case which
causes the hang with a single IO when pointed at the sd interface. See
the code at the bottom of this e-mail. It uses an SG_IO ioctl to issue
a single pass-through ATA identify device command. If the buffer
userspace gives for the read data has certain alignments, the task is
issued to the HBA but the HBA fails to respond. If run against the sg
interface, neither the test code nor smartctl causes a hang.
sd and sg handle the SG_IO ioctl slightly differently. Unless you
specifically set a flag to do direct IO, sg passes a buffer of its own,
which is page-aligned, to the block layer and later copies the result
into the userspace buffer regardless of its alignment. sd, on the other
hand, always does direct IO unless the userspace buffer fails an
alignment test at block/blk-map.c line 57, in which case a page-aligned
buffer is created and used for the transfer.
The alignment test currently checks for word-alignment, the default
setup by scsi_lib.c; therefore, userspace buffers of almost any
alignment are given directly to the HBA as DMA targets. The LSI 1068
hardware doesn't seem to like at least a couple of the alignments which
cross a page boundary (see the test code below). Curiously, many
page-boundary-crossing alignments do work just fine.
So, either the hardware has an bug handling certain alignments or the
hardware has a stricter alignment requirement than the driver is
advertising. If stricter alignment is required, then in no case should
misaligned buffers from userspace be allowed through without being
bounced or at least causing an error to be returned.
It seems the mptsas driver could use blk_queue_dma_alignment() to advertise
a stricter alignment requirement. If it does, sd does the right thing and
bounces misaligned buffers (see block/blk-map.c line 57). The following
patch to 2.6.34-rc5 makes my symptoms go away. I'm sure this is the wrong
place for this code, but it gets my idea across.
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Eric Moore [Thu, 22 Apr 2010 16:47:40 +0000 (10:47 -0600)]
[SCSI] mpt2sas: DIF Type 2 Protection Support
Adding DIF Type 2 protection support, as well as turning on 32 byte cdb's,
and setting the cdb length for > 16 byte in the SCSI_IO->control parameter.
Signed-off-by: Martin Petersen <martin.petersen@oracle.com> Signed-off-by: Eric Moore <eric.moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
srp_task needs to be setup before request_irq. The patch below fixes the oops.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Christof Schmitt [Mon, 21 Jun 2010 08:11:33 +0000 (10:11 +0200)]
[SCSI] zfcp: Update status read mempool
Commit 64deb6efdc5504ce97b5c1c6f281fffbc150bd93 changed the way status
read buffers are handled but forgot to adjust the mempool to the new
size. Add the call to resize the mempool after the exchange config
data. Also use the define instead of the hard coded number in the fsf
callback for consistency.
Christof Schmitt [Mon, 21 Jun 2010 08:11:32 +0000 (10:11 +0200)]
[SCSI] zfcp: Do not wait for SBALs on stopped queue
Trying to read the FC host statistics on an offline adapter results in
a 5 seconds wait. Reading the statistics tries to issue an exchange
port data request which first waits up to 5 seconds for an entry in
the request queue.
Change the strategy for getting a free SBAL to exit when the queue is
stopped. Reading the statistics will then fail without the wait.
Wayne Boyer [Thu, 3 Jun 2010 23:02:21 +0000 (16:02 -0700)]
[SCSI] ipr: fix resource path display and formatting
It was possible to overflow the buffer used to print out the formatted
version of the resource path. The fix is to limit the number of
bytes that get formatted.
This patch also updates the ipr_show_resource_path function to display the
resource address for devices that are attached to adapters that don't
support resource paths.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
wimax/i2400m: fix missing endian correction read in fw loader
net8139: fix a race at the end of NAPI
pktgen: Fix accuracy of inter-packet delay.
pkt_sched: gen_estimator: add a new lock
net: deliver skbs on inactive slaves to exact matches
ipv6: fix ICMP6_MIB_OUTERRORS
r8169: fix mdio_read and update mdio_write according to hw specs
gianfar: Revive the driver for eTSEC devices (disable timestamping)
caif: fix a couple range checks
phylib: Add support for the LXT973 phy.
net: Print num_rx_queues imbalance warning only when there are allocated queues
Linus Torvalds [Fri, 11 Jun 2010 21:18:47 +0000 (14:18 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: The file argument for fsync() is never null
Btrfs: handle ERR_PTR from posix_acl_from_xattr()
Btrfs: avoid BUG when dropping root and reference in same transaction
Btrfs: prohibit a operation of changing acl's mask when noacl mount option used
Btrfs: should add a permission check for setfacl
Btrfs: btrfs_lookup_dir_item() can return ERR_PTR
Btrfs: btrfs_read_fs_root_no_name() returns ERR_PTRs
Btrfs: unwind after btrfs_start_transaction() errors
Btrfs: btrfs_iget() returns ERR_PTR
Btrfs: handle kzalloc() failure in open_ctree()
Btrfs: handle error returns from btrfs_lookup_dir_item()
Btrfs: Fix BUG_ON for fs converted from extN
Btrfs: Fix null dereference in relocation.c
Btrfs: fix remap_file_pages error
Btrfs: uninitialized data is check_path_shared()
Btrfs: fix fallocate regression
Btrfs: fix loop device on top of btrfs
Linus Torvalds [Fri, 11 Jun 2010 21:15:44 +0000 (14:15 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
Yinghai Lu [Thu, 3 Jun 2010 20:43:03 +0000 (13:43 -0700)]
PCI: clear bridge resource range if BIOS assigned bad one
Yannick found that video does not work with 2.6.34. The cause of this
bug was that the BIOS had assigned the wrong range to the PCI bridge
above the video device. Before 2.6.34 the kernel would have shrunk
the size of the bridge window, but since d65245c PCI: don't shrink bridge resources
the kernel will avoid shrinking BIOS ranges.
So zero out the old range if we fail to claim it at boot time; this will
cause us to allocate a new range at startup, restoring the 2.6.34
behavior.
Jiri Slaby [Wed, 9 Jun 2010 20:31:13 +0000 (22:31 +0200)]
PCI: hotplug/cpqphp, fix NULL dereference
There are devices out there which are PCI Hot-plug controllers with
compaq PCI IDs, but are not bridges, hence have pdev->subordinate
NULL. But cpqphp expects the pointer to be non-NULL.
Add a check to the probe function to avoid oopses like:
BUG: unable to handle kernel NULL pointer dereference at 00000050
IP: [<f82e3c41>] cpqhpc_probe+0x951/0x1120 [cpqphp]
*pdpt = 0000000033779001 *pde = 0000000000000000
...
Bjorn Helgaas [Thu, 3 Jun 2010 19:47:18 +0000 (13:47 -0600)]
PCI: change resource collision messages from KERN_ERR to KERN_INFO
We can often deal with PCI resource issues by moving devices around. In
that case, there's no point in alarming the user with messages like these.
There are many bug reports where the message itself is the only problem,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/413419 .
Dan Carpenter [Sat, 29 May 2010 09:49:07 +0000 (09:49 +0000)]
Btrfs: The file argument for fsync() is never null
The "file" argument for fsync is never null so we can remove this check.
What drew my attention here is that 7ea8085910e: "drop unused dentry
argument to ->fsync" introduced an unconditional dereference at the
start of the function and that generated a smatch warning.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Sage Weil [Mon, 17 May 2010 17:15:27 +0000 (17:15 +0000)]
Btrfs: avoid BUG when dropping root and reference in same transaction
If btrfs_ioctl_snap_destroy() deletes a snapshot but finishes
with end_transaction(), the cleaner kthread may come in and
drop the root in the same transaction. If that's the case, the
root's refs still == 1 in the tree when btrfs_del_root() deletes
the item, because commit_fs_roots() hasn't updated it yet (that
happens during the commit).
This wasn't a problem before only because
btrfs_ioctl_snap_destroy() would commit the transaction before dropping
the dentry reference, so the dead root wouldn't get queued up until
after the fs root item was updated in the btree.
Since it is not an error to drop the root reference and the root in the
same transaction, just drop the BUG_ON() in btrfs_del_root().
Signed-off-by: Sage Weil <sage@newdream.net> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Shi Weihua [Tue, 18 May 2010 00:51:54 +0000 (00:51 +0000)]
Btrfs: prohibit a operation of changing acl's mask when noacl mount option used
when used Posix File System Test Suite(pjd-fstest) to test btrfs,
some cases about setfacl failed when noacl mount option used.
I simplified used commands in pjd-fstest, and the following steps
can reproduce it.
------------------------
# cd btrfs-part/
# mkdir aaa
# setfacl -m m::rw aaa <- successed, but not expected by pjd-fstest.
------------------------
I checked ext3, a warning message occured, like as:
setfacl: aaa/: Operation not supported
Certainly, it's expected by pjd-fstest.
So, i compared acl.c of btrfs and ext3. Based on that, a patch created.
Fortunately, it works.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Shi Weihua [Tue, 18 May 2010 00:50:32 +0000 (00:50 +0000)]
Btrfs: should add a permission check for setfacl
On btrfs, do the following
------------------
# su user1
# cd btrfs-part/
# touch aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rw-
group::rw-
other::r--
# su user2
# cd btrfs-part/
# setfacl -m u::rwx aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rwx <- successed to setfacl
group::rw-
other::r--
------------------
but we should prohibit it that user2 changing user1's acl.
In fact, on ext3 and other fs, a message occurs:
setfacl: aaa: Operation not permitted
This patch fixed it. Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_read_fs_root_no_name() returns ERR_PTRs on error so I added a
check for that. It's not clear to me if it can also return NULL
pointers or not so I left the original NULL pointer check as is.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Dan Carpenter [Sat, 29 May 2010 09:46:47 +0000 (09:46 +0000)]
Btrfs: unwind after btrfs_start_transaction() errors
This was added by a22285a6a3: "Btrfs: Integrate metadata reservation
with start_transaction". If we goto out here then we skip all the
unwinding and there are locks still held etc.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Fri, 11 Jun 2010 16:55:50 +0000 (09:55 -0700)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kbuild: Create output directory in Makefile.modbuiltin
kbuild: Generate modules.builtin in make modules
Linus Torvalds [Fri, 11 Jun 2010 16:55:21 +0000 (09:55 -0700)]
Merge branch 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid validate_cis failure on CIS override
pcmcia: dev_node removal bugfix
pcmcia: yenta_socket.c Remove extra #ifdef CONFIG_YENTA_TI
pcmcia: only keep saved I365_CSCINT flag if there is no PCI irq
Linus Torvalds [Fri, 11 Jun 2010 16:52:23 +0000 (09:52 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: try to send partial cap release on cap message on missing inode
ceph: release cap on import if we don't have the inode
ceph: fix misleading/incorrect debug message
ceph: fix atomic64_t initialization on ia64
ceph: fix lease revocation when seq doesn't match
ceph: fix f_namelen reported by statfs
ceph: fix memory leak in statfs
ceph: fix d_subdirs ordering problem
Dan Carpenter [Tue, 1 Jun 2010 08:23:11 +0000 (08:23 +0000)]
Btrfs: uninitialized data is check_path_shared()
refs can be used with uninitialized data if btrfs_lookup_extent_info()
fails on the first pass through the loop. In the original code if that
happens then check_path_shared() probably returns 1, this patch
changes it to return 1 for safety.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Mon, 7 Jun 2010 18:26:37 +0000 (18:26 +0000)]
Btrfs: fix fallocate regression
Seems that when btrfs_fallocate was converted to use the new ENOSPC stuff we
dropped passing the mode to the function that actually does the preallocation.
This breaks anybody who wants to use FALLOC_FL_KEEP_SIZE. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Daniel Turull [Fri, 11 Jun 2010 06:08:11 +0000 (23:08 -0700)]
pktgen: Fix accuracy of inter-packet delay.
This patch correct a bug in the delay of pktgen.
It makes sure the inter-packet interval is accurate.
Signed-off-by: Daniel Turull <daniel.turull@gmail.com> Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 3 Jun 2010 09:30:11 +0000 (09:30 +0000)]
net: deliver skbs on inactive slaves to exact matches
Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop(). This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.
For example,
vlanx -> bond0 -> ethx
will be dropped in the vlan path and not delivered to any
packet handlers at all. However,
bond0 -> vlanx -> ethx
and
bond0 -> ethx
will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.
This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv(). Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly. This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.
I have tested the following 4 configurations in failover modes
and load balancing modes.
# bond0 -> ethx
# vlanx -> bond0 -> ethx
# bond0 -> vlanx -> ethx
# bond0 -> ethx
|
vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sage Weil [Wed, 9 Jun 2010 23:52:04 +0000 (16:52 -0700)]
ceph: try to send partial cap release on cap message on missing inode
If we have enough memory to allocate a new cap release message, do so, so
that we can send a partial release message immediately. This keeps us from
making the MDS wait when the cap release it needs is in a partially full
release message.
If we fail because of ENOMEM, oh well, they'll just have to wait a bit
longer.
Sage Weil [Wed, 9 Jun 2010 23:47:10 +0000 (16:47 -0700)]
ceph: release cap on import if we don't have the inode
If we get an IMPORT that give us a cap, but we don't have the inode, queue
a release (and try to send it immediately) so that the MDS doesn't get
stuck waiting for us.
Catalin Marinas [Thu, 10 Jun 2010 16:02:12 +0000 (17:02 +0100)]
sata_sil24: Use memory barriers before issuing commands
The data in the cmd_block buffers may reach the main memory after the
writel() to the device ports. This patch introduces two calls to wmb()
to ensure the relative ordering.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Colin Tuckley <colin.tuckley@arm.com> Cc: Tejun Heo <tj@kernel.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan Carpenter [Wed, 9 Jun 2010 12:01:54 +0000 (14:01 +0200)]
sata_sil24: memset() overflow
cb->atapi.cdb is an array of 16 u8 elements. The call too memset()
would set the first part of the sge array to zero as well. It's not
a packed struct.
This one has been around for five years. I found it with Smatch. I
think the reason no one has seen it before is because we normally call
sil24_fill_sg() and that overwrites sge with proper information?
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Thu, 10 Jun 2010 17:53:14 +0000 (10:53 -0700)]
Merge branch 'kvm-updates/2.6.35' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.35' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: read apic->irr with ioapic lock held
KVM: ia64: Add missing spin_unlock in kvm_arch_hardware_enable()
KVM: Fix order passed to iommu_unmap
KVM: MMU: Remove user access when allowing kernel access to gpte.w=0 page
KVM: MMU: invalidate and flush on spte small->large page size change
KVM: SVM: Implement workaround for Erratum 383
KVM: SVM: Handle MCEs early in the vmexit process
KVM: powerpc: fix init/exit annotation
Nick Piggin [Tue, 25 May 2010 15:51:19 +0000 (01:51 +1000)]
block: bd_start_claiming cleanup
I don't like the subtle multi-context code in bd_claim (ie. detects where it
has been called based on bd_claiming). It seems clearer to just require a new
function to finish a 2-part claim.
Also improve commentary in bd_start_claiming as to how it should
be used.
Linus Torvalds [Thu, 10 Jun 2010 16:34:15 +0000 (09:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/spi: patch for the unuseful variable removal
ALSA: hda - Add SSID table for iMac7,1.
ALSA: hda - Add SSID table for MacBookAir1,1
ALSA: hda - Add SSID table for MacBookAir2,1
ALSA: atmel: set "channel A event" output to debug
Linus Torvalds [Thu, 10 Jun 2010 16:30:09 +0000 (09:30 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix null pointer deref with SEND_SIG_FORCED
perf: Fix signed comparison in perf_adjust_period()
powerpc/oprofile: fix potential buffer overrun in op_model_cell.c
perf symbols: Set the DSO long name when using symbol_conf.vmlinux_name
Linus Torvalds [Thu, 10 Jun 2010 14:35:41 +0000 (07:35 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6164/1: Add kto and kfrom to input operands list.
ARM: 6166/1: Proper prefetch abort handling on pre-ARMv6
ARM: 6165/1: trap overflows on highmem pages from kmap_atomic when debugging
ARM: 6152/1: ux500 make it possible to disable localtimers
[ARM] pxa/spitz: Correctly register WM8750
[ARM] pxa/palmtc: storage class should be before const qualifier
ARM: 6146/1: sa1111: Prevent deadlock in resume path
ARM: 6145/1: ux500 MTU clockrate correction
ARM: 6144/1: TCM memory bug freeing bug
ARM: VFP: Fix vfp_put_double() for d16-d31
Timo Teräs [Thu, 10 Jun 2010 00:31:48 +0000 (17:31 -0700)]
r8169: fix mdio_read and update mdio_write according to hw specs
Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.
Signed-off-by: Timo Teräs <timo.teras@iki.fi> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Wed, 9 Jun 2010 23:27:08 +0000 (16:27 -0700)]
gianfar: Revive the driver for eTSEC devices (disable timestamping)
Since commit cc772ab7cdcaa24d1fae332d92a1602788644f7a ("gianfar: Add
hardware RX timestamping support"), the driver no longer works on
at least MPC8313ERDB and MPC8568EMDS boards (and possibly much more
boards as well).
That's how MPC8313 Reference Manual describes RCTRL_TS_ENABLE bit:
Timestamp incoming packets as padding bytes. PAL field is set
to 8 if the PAL field is programmed to less than 8. Must be set
to zero if TMR_CTRL[TE]=0.
I see that the commit above sets this bit, but it doesn't handle
TMR_CTRL. Manfred probably had this bit set by the firmware for
his boards. But obviously this isn't true for all boards in the
wild.
Also, I recall that Freescale BSPs were explicitly disabling the
timestamping because of a performance drop.
For now, the best way to deal with this is just disable the
timestamping, and later we can discuss proper device tree bindings
and implement enabling this feature via some property.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 7 Jun 2010 04:51:58 +0000 (04:51 +0000)]
caif: fix a couple range checks
The extra ! character means that these conditions are always false.
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Mon, 7 Jun 2010 05:39:32 +0000 (05:39 +0000)]
phylib: Add support for the LXT973 phy.
This patch implements a work around for Erratum 5, "3.3 V Fiber Speed
Selection." If the hardware wiring does not respect this erratum, then
fiber optic mode will not work properly.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Marek [Mon, 7 Jun 2010 20:22:12 +0000 (22:22 +0200)]
kbuild: Generate modules.builtin in make modules
Generating the file in make modules_install was broken as well, because
it didn't work in a readonly filesystem and otherwise it generated a
root-owned file which is not wanted.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Michal Marek <mmarek@suse.cz>
Tim Gardner [Tue, 8 Jun 2010 23:51:27 +0000 (17:51 -0600)]
net: Print num_rx_queues imbalance warning only when there are allocated queues
BugLink: http://bugs.launchpad.net/bugs/591416
There are a number of network drivers (bridge, bonding, etc) that are not yet
receive multi-queue enabled and use alloc_netdev(), so don't print a
num_rx_queues imbalance warning in that case.
Also, only print the warning once for those drivers that _are_ multi-queue
enabled.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
mac80211: fix deauth before assoc
iwlwifi: add missing rcu_read_lock
mac80211: fix function pointer check
wireless: remove my name from the maintainer list
ath5k: fix NULL pointer in antenna configuration
p54usb: Add device ID for Dell WLA3310 USB
wl1251: fix a memory leak in probe
ipmr: dont corrupt lists
8139too: fix buffer overrun in rtl8139_init_board
asix: check packet size against mtu+ETH_HLEN instead of ETH_FRAME_LEN
r8169: fix random mdio_write failures
ip6mr: fix a typo in ip6mr_for_each_table()
iwlwifi: move sysfs_create_group to post request firmware
iwlwifi: add name to Maintainers list
iwl3945: fix internal scan
iwl3945: enable stuck queue detection on 3945
ipv6: avoid high order allocations
ath5k: retain promiscuous setting
ath5k: depend on CONFIG_PM_SLEEP for suspend/resume functions
mac80211: process station blockack action frames from work
...
Linus Torvalds [Wed, 9 Jun 2010 19:43:04 +0000 (12:43 -0700)]
Merge branch 'for-2.6.35' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.35' of git://linux-nfs.org/~bfields/linux:
nfsd4: shut down callback queue outside state lock
nfsd: nfsd_setattr needs to call commit_metadata
David Howells [Wed, 9 Jun 2010 18:52:22 +0000 (19:52 +0100)]
FRV: Reinstate null behaviour for the GDB remote protocol 'p' command
Reinstate the null behaviour that the in-kernel gdbstub had for the GDB
remote protocol 'p' command (retrieve a single register value) prior to
commit 7ca8b9c0dafd ("frv: extend gdbstub to support more features of
gdb").
Before that, the 'p' command just returned an empty reply, which causes
gdb to then go and use the 'g' command. However, since that commit, the
'p' command returns an error string, which causes gdb to abort its
connection to the target.
Not all gdb versions are affected, some use try 'g' first, and if that
works, don't bother with 'p', and so don't see the error.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Walker [Mon, 24 May 2010 17:15:00 +0000 (10:15 -0700)]
mmc: msm: fix compile error on MSM7x30
MSM7x30 isn't supported in this driver yet. If ones tried to compile it in
with MSM7x30 configure you get,
linux-2.6/drivers/mmc/host/msm_sdcc.c: In function 'msmsdcc_fifo_addr':
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: 'MSM_SDC1_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: (Each undeclared identifier is reported only once
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: for each function it appears in.)
linux-2.6/drivers/mmc/host/msm_sdcc.c:167: error: 'MSM_SDC2_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:169: error: 'MSM_SDC3_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:171: error: 'MSM_SDC4_PHYS' undeclared (first use in this function)
So we add a Kconfig check to prevent this.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Alan Cox [Wed, 9 Jun 2010 08:39:49 +0000 (09:39 +0100)]
misc: Fix allocation 'borrowed' by vhost_net
10, 233 is allocated officially to /dev/kmview which is shipping in
Ubuntu and Debian distributions. vhost_net seem to have borrowed it
without making a proper request and this causes regressions in the other
distributions.
vhost_net can use a dynamic minor so use that instead. Also update the
file with a comment to try and avoid future misunderstandings.
cc: stable@kernel.org Signed-off-by: Alan Cox <device@lanana.org>
[ We should have caught this before 2.6.34 got released. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-beck.git / log