Nathan Sullivan [Wed, 21 Oct 2015 19:17:04 +0000 (14:17 -0500)]
net/phy: micrel: Add workaround for bad autoneg
Very rarely, the KSZ9031 will appear to complete autonegotiation, but
will drop all traffic afterwards. When this happens, the idle error
count will read 0xFF after autonegotiation completes. Reset the PHY
when in that state.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 23 Oct 2015 09:49:41 +0000 (02:49 -0700)]
Merge branch 'ipv6-overflow-arith'
Hannes Frederic Sowa says:
====================
overflow-arith: begin to add support for overflow builtins functions
I add a new header, linux/overflow-arith.h, as the central place to add
overflow and wrap-around checking functions. The reason I am doing so
is that it can make use of compiler supported builtin functions which
can leverage hardware.
As I need this for a fix in the ipv6 stack, which is also included in
this series, I propose to add it sooner than later over Davem's net
tree. This is also the reason why I start slowly with only the one
function I need at this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: protect mtu calculation of wrap-around and infinite loop by rounding issues
Raw sockets with hdrincl enabled can insert ipv6 extension headers
right into the data stream. In case we need to fragment those packets,
we reparse the options header to find the place where we can insert
the fragment header. If the extension headers exceed the link's MTU we
actually cannot make progress in such a case.
Instead of ending up in broken arithmetic or rounding towards 0 and
entering an endless loop in ip6_fragment, just prevent those cases by
aborting early and signal -EMSGSIZE to user space.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
overflow-arith: begin to add support for overflow builtin functions
The idea of the overflow-arith.h header is to collect overflow checking
functions in one central place.
If gcc compiler supports the __builtin_overflow_* builtins we use them
because they might give better performance, otherwise the code falls
back to normal overflow checking functions.
The builtin_overflow functions are supported by gcc-5 and clang. The
matter of supporting clang is to just provide a corresponding
CC_HAVE_BUILTIN_OVERFLOW, because the specific overflow checking builtins
don't differ between gcc and clang.
I just provide overflow_usub function here as I intend this to get merged
into net, more functions will definitely follow as they are needed.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Shewmaker [Mon, 19 Oct 2015 04:59:08 +0000 (21:59 -0700)]
tcp: allow dctcp alpha to drop to zero
If alpha is strictly reduced by alpha >> dctcp_shift_g and if alpha is less
than 1 << dctcp_shift_g, then alpha may never reach zero. For example,
given shift_g=4 and alpha=15, alpha >> dctcp_shift_g yields 0 and alpha
remains 15. The effect isn't noticeable in this case below cwnd=137, but
could gradually drive uncongested flows with leftover alpha down to
cwnd=137. A larger dctcp_shift_g would have a greater effect.
This change causes alpha=15 to drop to 0 instead of being decrementing by 1
as it would when alpha=16. However, it requires one less conditional to
implement since it doesn't have to guard against subtracting 1 from 0U. A
decay of 15 is not unreasonable since an equal or greater amount occurs at
alpha >= 240.
Signed-off-by: Andrew G. Shewmaker <agshew@gmail.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
lucien [Fri, 23 Oct 2015 07:36:53 +0000 (15:36 +0800)]
ipv6: fix the incorrect return value of throw route
The error condition -EAGAIN, which is signaled by throw routes, tells
the rules framework to walk on searching for next matches. If the walk
ends and we stop walking the rules with the result of a throw route we
have to translate the error conditions to -ENETUNREACH.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 23 Oct 2015 04:57:05 +0000 (00:57 -0400)]
macvtap: unbreak receiving of gro skb with frag list
We don't have fraglist support in TAP_FEATURES. This will lead
software segmentation of gro skb with frag list. Fixes by having
frag list support in TAP_FEATURES.
With this patch single session of netperf receiving were restored from
about 5Gb/s to about 12Gb/s on mlx4.
Fixes a567dd6252 ("macvtap: simplify usage of tap_features") Cc: Vlad Yasevich <vyasevic@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Fri, 23 Oct 2015 01:17:16 +0000 (18:17 -0700)]
openvswitch: Fix egress tunnel info.
While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices. Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.
Fixes: 614732eaa12d ("openvswitch: Use regular VXLAN net_device device"). Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 23 Oct 2015 02:02:08 +0000 (19:02 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-22
This series contains fixes to i40e only.
Jesse provides two small fixes for i40e, first fixes counters that were
being displayed incorrectly due to indexing beyond the array of strings
when printing stats. Then fixed the fact that the driver was printing
a message about not being able to assign VMDq because a lack of MSI-X
vectors, when it was not true. It was due to a line missing that
initialized a variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jorgen Hansen [Thu, 22 Oct 2015 15:25:25 +0000 (08:25 -0700)]
VSOCK: Fix lockdep issue.
The recent fix for the vsock sock_put issue used the wrong
initializer for the transport spin_lock causing an issue when
running with lockdep checking.
Testing: Verified fix on kernel with lockdep enabled.
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The code was setting up stats that were not being initialized.
This caused several counters to be displayed incorrectly, due
to indexing beyond the array of strings when printing stats.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Fix IPsec pre-encap fragmentation for GSO packets.
From Herbert Xu.
2) Fix some header checks in _decode_session6.
We skip the header informations if the data pointer points
already behind the header in question for some protocols.
This is because we call pskb_may_pull with a negative value
converted to unsigened int from pskb_may_pull in this case.
Skipping the header informations can lead to incorrect policy
lookups. From Mathias Krause.
3) Allow to change the replay threshold and expiry timer of a
state without having to set other attributes like replay
counter and byte lifetime. Changing these other attributes
may break the SA. From Michael Rossberg.
4) Fix pmtu discovery for local generated packets.
We may fail dispatch to the inner address family.
As a reault, the local error handler is not called
and the mtu value is not reported back to userspace.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 21 Oct 2015 15:42:22 +0000 (08:42 -0700)]
net: ipv6: Dont add RT6_LOOKUP_F_IFACE flag if saddr set
741a11d9e410 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set")
adds the RT6_LOOKUP_F_IFACE flag to make device index mismatch fatal if
oif is given. Hajime reported that this change breaks the Mobile IPv6
use case that wants to force the message through one interface yet use
the source address from another interface. Handle this case by only
adding the flag if oif is set and saddr is not set.
Fixes: 741a11d9e410 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set") Cc: Hajime Tazaki <thehajime@gmail.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Oct 2015 14:23:25 +0000 (07:23 -0700)]
Merge branch 'isdn-null-deref'
Karsten Keil says:
====================
Fix potential NULL pointer access and memory leak in ISDN layer2 functions
Insu Yun did brinup the issue with not checking the skb_clone() return
value in the layer2 I-frame ull functions.
This series fix the issue in a way which avoid protocol violations/data loss
on a temporary memory shortage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Wed, 21 Oct 2015 12:18:39 +0000 (14:18 +0200)]
mISDN: fix OOM condition for sending queued I-Frames
The old code did not check the return value of skb_clone().
The extra skb_clone() is not needed at all, if using skb_realloc_headroom()
instead, which gives us a private copy with enough headroom as well.
We need to requeue the original skb if the call failed, because we cannot
inform upper layers about the data loss. Restructure the code to minimise
rollback effort if it happens.
This fix kernel bug #86091
Thanks to Insu Yun <wuninsu@gmail.com> to remind me on this issue.
Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Wed, 21 Oct 2015 12:18:38 +0000 (14:18 +0200)]
ISDN: fix OOM condition for sending queued I-Frames
The skb_clone() return value was not checked and the skb_realloc_headroom()
usage was wrong, the old skb was not freed. It turned out, that the
skb_clone is not needed at all, the skb_realloc_headroom() will create a
private copy with enough headroom and the original SKB can be used for the
ACK queue.
We need to requeue the original skb if the call failed, since the upper
layer cannot be informed about memory shortage.
Thanks to Insu Yun <wuninsu@gmail.com> to remind me on this issue.
Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Jorgen Hansen [Wed, 21 Oct 2015 11:53:56 +0000 (04:53 -0700)]
VSOCK: sock_put wasn't safe to call in interrupt context
In the vsock vmci_transport driver, sock_put wasn't safe to call
in interrupt context, since that may call the vsock destructor
which in turn calls several functions that should only be called
from process context. This change defers the callling of these
functions to a worker thread. All these functions were
deallocation of resources related to the transport itself.
Furthermore, an unused callback was removed to simplify the
cleanup.
Multiple customers have been hitting this issue when using
VMware tools on vSphere 2015.
Also added a version to the vmci transport module (starting from
1.0.2.0-k since up until now it appears that this module was
sharing version with vsock that is currently at 1.0.1.0-k).
Reviewed-by: Aditya Asarwade <asarwade@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Herrmann [Wed, 21 Oct 2015 09:47:43 +0000 (11:47 +0200)]
netlink: fix locking around NETLINK_LIST_MEMBERSHIPS
Currently, NETLINK_LIST_MEMBERSHIPS grabs the netlink table while copying
the membership state to user-space. However, grabing the netlink table is
effectively a write_lock_irq(), and as such we should not be triggering
page-faults in the critical section.
This can be easily reproduced by the following snippet:
int s = socket(AF_NETLINK, SOCK_RAW, NETLINK_ROUTE);
void *p = mmap(0, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANON, -1, 0);
int r = getsockopt(s, 0x10e, 9, p, (void*)((char*)p + 4092));
This should work just fine, but currently triggers EFAULT and a possible
WARN_ON below handle_mm_fault().
Fix this by reducing locking of NETLINK_LIST_MEMBERSHIPS to a read-side
lock. The write-lock was overkill in the first place, and the read-lock
allows page-faults just fine.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew F. Davis [Tue, 20 Oct 2015 21:28:57 +0000 (16:28 -0500)]
net: phy: dp83848: Add TI DP83848 Ethernet PHY
Add support for the TI DP83848 Ethernet PHY device.
The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant
single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting
the MII and RMII interfaces.
Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Tue, 20 Oct 2015 08:42:24 +0000 (10:42 +0200)]
net: sun4i-emac: Properly free resources on probe failure and remove
Fix sun4i-emac not releasing the following resources:
-iomapped memory not released on probe-failure nor on remove
-clock not getting disabled on probe-failure nor on remove
-sram not being released on remove
And while at it also add error checking to the clk_prepare_enable call
done on probe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Tue, 20 Oct 2015 02:19:00 +0000 (19:19 -0700)]
openvswitch: Serialize nested ct actions if provided
If userspace provides a ct action with no nested mark or label, then the
storage for these fields is zeroed. Later when actions are requested,
such zeroed fields are serialized even though userspace didn't
originally specify them. Fix the behaviour by ensuring that no action is
serialized in this case, and reject actions where userspace attempts to
set these fields with mask=0. This should make netlink marshalling
consistent across deserialization/reserialization.
Reported-by: Jarno Rajahalme <jrajahalme@nicira.com> Signed-off-by: Joe Stringer <joestringer@nicira.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Tue, 20 Oct 2015 02:18:59 +0000 (19:18 -0700)]
openvswitch: Mark connections new when not confirmed.
New, related connections are marked as such as part of ovs_ct_lookup(),
but they are not marked as "new" if the commit flag is used. Make this
consistent by setting the "new" flag whenever !nf_ct_is_confirmed(ct).
Reported-by: Jarno Rajahalme <jrajahalme@nicira.com> Signed-off-by: Joe Stringer <joestringer@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Tue, 20 Oct 2015 02:18:58 +0000 (19:18 -0700)]
openvswitch: Clarify conntrack COMMIT behaviour
The presence of this attribute does not modify the ct_state for the
current packet, only future packets. Make this more clear in the header
definition.
Signed-off-by: Joe Stringer <joestringer@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Tue, 20 Oct 2015 02:18:57 +0000 (19:18 -0700)]
openvswitch: Reject ct_state masks for unknown bits
Currently, 0-bits are generated in ct_state where the bit position is
undefined, and matches are accepted on these bit-positions. If userspace
requests to match the 0-value for this bit then it may expect only a
subset of traffic to match this value, whereas currently all packets
will have this bit set to 0. Fix this by rejecting such masks.
Signed-off-by: Joe Stringer <joestringer@nicira.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Since tcp_xmit_probe_skb() can be called from process context, use
NET_INC_STATS() instead of NET_INC_STATS_BH().
Fixes: e520af48c7e5 ("tcp: add TCPWinProbe and TCPKeepAlive SNMP counters") Signed-off-by: Renato Westphal <renatow@taghos.com.br> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 19 Oct 2015 15:43:11 +0000 (11:43 -0400)]
tipc: conditionally expand buffer headroom over udp tunnel
In commit d999297c3dbbe ("tipc: reduce locking scope during packet reception")
we altered the packet retransmission function. Since then, when
restransmitting packets, we create a clone of the original buffer
using __pskb_copy(skb, MIN_H_SIZE), where MIN_H_SIZE is the size of
the area we want to have copied, but also the smallest possible TIPC
packet size. The value of MIN_H_SIZE is 24.
Unfortunately, __pskb_copy() also has the effect that the headroom
of the cloned buffer takes the size MIN_H_SIZE. This is too small
for carrying the packet over the UDP tunnel bearer, which requires
a minimum headroom of 28 bytes. A change to just use pskb_copy()
lets the clone inherit the original headroom of 80 bytes, but also
assumes that the copied data area is of at least that size, something
that is not always the case. So that is not a viable solution.
We now fix this by adding a check for sufficient headroom in the
transmit function of udp_media.c, and expanding it when necessary.
Fixes: commit d999297c3dbbe ("tipc: reduce locking scope during packet reception") Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Schwab [Mon, 19 Oct 2015 15:37:13 +0000 (17:37 +0200)]
net: cavium: change NET_VENDOR_CAVIUM to bool
CONFIG_NET_VENDOR_CAVIUM is only used to hide/show config options and to
include subdirectories in the build, so it doesn't make sense to make it
tristate.
Signed-off-by: Andreas Schwab <schwab@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 19 Oct 2015 15:33:00 +0000 (11:33 -0400)]
tipc: allow non-linear first fragment buffer
The current code for message reassembly is erroneously assuming that
the the first arriving fragment buffer always is linear, and then goes
ahead resetting the fragment list of that buffer in anticipation of
more arriving fragments.
However, if the buffer already happens to be non-linear, we will
inadvertently drop the already attached fragment list, and later
on trig a BUG() in __pskb_pull_tail().
We see this happen when running fragmented TIPC multicast across UDP,
something made possible since
commit d0f91938bede ("tipc: add ip/udp media type")
We fix this by not resetting the fragment list when the buffer is non-
linear, and by initiatlizing our private fragment list tail pointer to
the tail of the existing fragment list.
Fixes: commit d0f91938bede ("tipc: add ip/udp media type") Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
James Morse [Mon, 19 Oct 2015 15:31:55 +0000 (16:31 +0100)]
openvswitch: Allocate memory for ovs internal device stats.
"openvswitch: Remove vport stats" removed the per-vport statistics, in
order to use the netdev's statistics fields.
"openvswitch: Fix ovs_vport_get_stats()" fixed the export of these stats
to user-space, by using the provided netdev_ops to collate them - but ovs
internal devices still use an unallocated dev->tstats field to count
packets, which are no longer exported by this api.
Allocate the dev->tstats field for ovs internal devices, and wire up
ndo_get_stats64 with the original implementation of
ovs_vport_get_stats().
On its own, "openvswitch: Fix ovs_vport_get_stats()" fixes the OOPs,
unmasking a full-on panic on arm64:
Fixes: 8c876639c985 ("openvswitch: Remove vport stats.") Signed-off-by: James Morse <james.morse@arm.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 19 Oct 2015 15:26:05 +0000 (08:26 -0700)]
net: Really fix vti6 with oif in dst lookups
6e28b000825d ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.
Fixes: 42a7b32b73d6 ("xfrm: Add oif to dst lookups") Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 19 Oct 2015 13:21:37 +0000 (09:21 -0400)]
tipc: extend broadcast link window size
The default fix broadcast window size is currently set to 20 packets.
This is a very low value, set at a time when we were still testing on
10 Mb/s hubs, and a change to it is long overdue.
Commit 7845989cb4b3da1db ("net: tipc: fix stall during bclink wakeup procedure")
revealed a problem with this low value. For messages of importance LOW,
the backlog queue limit will be calculated to 30 packets, while a
single, maximum sized message of 66000 bytes, carried across a 1500 MTU
network consists of 46 packets.
This leads to the following scenario (among others leading to the same
situation):
1: Msg 1 of 46 packets is sent. 20 packets go to the transmit queue, 26
packets to the backlog queue.
2: Msg 2 of 46 packets is attempted sent, but rejected because there is
no more space in the backlog queue at this level. The sender is added
to the wakeup queue with a "pending packets chain size" number of 46.
3: Some packets in the transmit queue are acked and released. We try to
wake up the sender, but the pending size of 46 is bigger than the LOW
wakeup limit of 30, so this doesn't happen.
5: Subsequent acks releases all the remaining buffers. Each time we test
for the wakeup criteria and find that 46 still is larger than 30,
even after both the transmit and the backlog queues are empty.
6: The sender is never woken up and given a chance to send its message.
He is stuck.
We could now loosen the wakeup criteria (used by link_prepare_wakeup())
to become equal to the send criteria (used by tipc_link_xmit()), i.e.,
by ignoring the "pending packets chain size" value altogether, or we can
just increase the queue limits so that the criteria can be satisfied
anyway. There are good reasons (potentially multiple waiting senders) to
not opt for the former solution, so we choose the latter one.
This commit fixes the problem by giving the broadcast link window a
default value of 50 packets. We also introduce a new minimum link
window size BCLINK_MIN_WIN of 32, which is enough to always avoid the
described situation. Finally, in order to not break any existing users
which may set the window explicitly, we enforce that the window is set
to the new minimum value in case the user is trying to set it to
anything lower.
Fixes: 7845989cb4b3da1db ("net: tipc: fix stall during bclink wakeup procedure") Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 19 Oct 2015 10:16:49 +0000 (13:16 +0300)]
irda: precedence bug in irlmp_seq_hb_idx()
This is decrementing the pointer, instead of the value stored in the
pointer. KASan detects it as an out of bounds reference.
Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Jin [Mon, 19 Oct 2015 05:37:17 +0000 (13:37 +0800)]
xen-netfront: update num_queues to real created
Sometimes xennet_create_queues() may failed to created all requested
queues, we need to update num_queues to real created to avoid NULL
pointer dereference.
Signed-off-by: Joe Jin <joe.jin@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: David S. Miller <davem@davemloft.net> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Oct 2015 14:36:51 +0000 (07:36 -0700)]
Merge branch 'mv643xx-fixes'
Philipp Kirchhofer says:
====================
net: mv643xx_eth: TSO TX data corruption fixes
as previously discussed [1] the mv643xx_eth driver has some
issues with data corruption when using TCP segmentation offload (TSO).
The following patch set improves this situation by fixing two data
corruption bugs in the TSO TX path.
Before applying the patches repeatedly accessing large files located on
a SMB share on my NSA325 NAS with TSO enabled resulted in different
hash sums, which confirmed that data corruption is happening during
file transfer. After applying the patches the hash sums were the same.
As this is my first patch submission please feel free to point out any
issues with the patch set.
net: mv643xx_eth: Defer writing the first TX descriptor when using TSO
To prevent a race between the TX DMA engine and the CPU the writing of the
first transmit descriptor must be deferred until all following descriptors
have been updated. The network card may otherwise start transmitting before
all packet descriptors are set up correctly, which leads to data corruption
or an aborted transmit operation.
This deferral is already done in the non-TSO TX path, implement it also in
the TSO TX path.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mv643xx_eth: Ensure proper data alignment in TSO TX path
The TX DMA engine requires that buffers with a size of 8 bytes or smaller
must be 64 bit aligned. This requirement may be violated when doing TSO,
as in this case larger skb frags can be broken up and transmitted in small
parts with then inappropriate alignment.
Fix this by checking for proper alignment before handing a buffer to the
DMA engine. If the data is misaligned realign it by copying it into the
TSO header data area.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Oct 2015 13:41:51 +0000 (06:41 -0700)]
Merge branch 'smsc-energy-detect'
Heiko Schocher says:
====================
net, phy, smsc: add posibility to disable energy detect mode
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Therefore the property "smsc,disable-energy-detect" is
introduced.
Patch 1 introduces phy-handle support for the ti,cpsw
driver. This is needed now for the smsc phy.
Patch 2 adds the disable energy mode functionality
to the smsc phy
Changes in v2:
- add comments from Florian Fainelli
- I did not change disable property name into enable
because I fear to break existing behaviour
- add smsc vendor prefix
- remove CONFIG_OF and use __maybe_unused
- introduce "phy-handle" ability into ti,cpsw
driver, so I can remove bogus:
if (!of_node && dev->parent->of_node)
of_node = dev->parent->of_node;
construct. Therefore new patch for the ti,cpsw
driver is necessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
Steffen Klassert [Mon, 19 Oct 2015 08:30:05 +0000 (10:30 +0200)]
xfrm: Fix pmtu discovery for local generated packets.
Commit 044a832a777 ("xfrm: Fix local error reporting crash
with interfamily tunnels") moved the setting of skb->protocol
behind the last access of the inner mode family to fix an
interfamily crash. Unfortunately now skb->protocol might not
be set at all, so we fail dispatch to the inner address family.
As a reault, the local error handler is not called and the
mtu value is not reported back to userspace.
We fix this by setting skb->protocol on message size errors
before we call xfrm_local_error.
Fixes: 044a832a7779c ("xfrm: Fix local error reporting crash with interfamily tunnels") Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Florian Fainelli [Sat, 17 Oct 2015 21:22:46 +0000 (14:22 -0700)]
net: bcmgenet: Fix early link interrupt enabling
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dcb36 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Fri, 16 Oct 2015 23:36:00 +0000 (16:36 -0700)]
tunnels: Don't require remote endpoint or ID during creation.
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Fri, 16 Oct 2015 18:08:18 +0000 (11:08 -0700)]
openvswitch: Scrub skb between namespaces
If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.
This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Oct 2015 05:23:33 +0000 (22:23 -0700)]
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2015-10-16
First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.
The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.
The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.
I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arad, Ronen [Thu, 15 Oct 2015 08:55:17 +0000 (01:55 -0700)]
netlink: Trim skb to alloc size to avoid MSG_TRUNC
netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.
netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.
Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).
It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.
This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Oct 2015 19:07:48 +0000 (12:07 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes for the I2C subsystem.
Kieran found a flaw in the recently renewed wake irq handling. Mika
handled a user bug report where the ACPI info turned out to be
unusable. I updated MAINTAINERS so that such bug reports will sooner
get to the right people. Geert pointed me to a problem of some i2c
drivers regarding PM which I fixed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
i2c: designware-platdrv: enable RuntimePM before registering to the core
i2c: s3c2410: enable RuntimePM before registering to the core
i2c: rcar: enable RuntimePM before registering to the core
i2c: return probe deferred status on dev_pm_domain_attach
Mika Westerberg [Thu, 24 Sep 2015 09:06:54 +0000 (12:06 +0300)]
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Eric Dumazet [Wed, 30 Sep 2015 01:52:25 +0000 (18:52 -0700)]
net: add pfmemalloc check in sk_add_backlog()
Greg reported crashes hitting the following check in __sk_backlog_rcv()
BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));
The pfmemalloc bit is currently checked in sk_filter().
This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.
For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.
Fixes: b4b9e35585089 ("netvm: set PF_MEMALLOC as appropriate during SKB processing") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Greg Thelen <gthelen@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Borisov [Fri, 16 Oct 2015 06:40:28 +0000 (09:40 +0300)]
netfilter: ipset: Fix sleeping memory allocation in atomic context
Commit 00590fdd5be0 introduced RCU locking in list type and in
doing so introduced a memory allocation in list_set_add, which
is done in an atomic context, due to the fact that ipset rcu
list modifications are serialised with a spin lock. The reason
why we can't use a mutex is that in addition to modifying the
list with ipset commands, it's also being modified when a
particular ipset rule timeout expires aka garbage collection.
This gc is triggered from set_cleanup_entries, which in turn
is invoked from a timer thus requiring the lock to be bh-safe.
Concretely the following call chain can lead to "sleeping function
called in atomic context" splat:
call_ad -> list_set_uadt -> list_set_uadd -> kzalloc(, GFP_KERNEL).
And since GFP_KERNEL allows initiating direct reclaim thus
potentially sleeping in the allocation path.
To fix the issue change the allocation type to GFP_ATOMIC, to
correctly reflect that it is occuring in an atomic context.
Fixes: 00590fdd5be0 ("netfilter: ipset: Introduce RCU locking in list type") Signed-off-by: Nikolay Borisov <kernel@kyup.com> Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Linus Torvalds [Sat, 17 Oct 2015 00:39:27 +0000 (17:39 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
Linus Torvalds [Sat, 17 Oct 2015 00:11:14 +0000 (17:11 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"Just one revert for Armada XP devices: the conversion to
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name().
We could make of_clk_get_parent_name() more robust, but that
may have unintended side-effects, so we'll do that in the
next version"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
Linus Torvalds [Fri, 16 Oct 2015 20:03:05 +0000 (13:03 -0700)]
Merge tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two DM target error path cleanup fixes (one for stable in DM thinp and
one for a v4.3-rc5 thinko in DM snapshot)"
* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix missing pool reference count decrement in pool_ctr error path
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
Linus Torvalds [Fri, 16 Oct 2015 19:55:34 +0000 (12:55 -0700)]
Merge branch 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I have two more bug fixes for btrfs.
My commit fixes a bug we hit last week at FB, a combination of lots of
hard links and an admin command to resolve inode numbers.
Dave is adding checks to make sure balance on current kernels ignores
filters it doesn't understand. The penalty for being wrong is just
doing more work (not crashing etc), but it's a good fix"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix use after free iterating extrefs
btrfs: check unsupported filters in balance arguments
Linus Torvalds [Fri, 16 Oct 2015 19:47:02 +0000 (12:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
Linus Torvalds [Fri, 16 Oct 2015 19:25:54 +0000 (12:25 -0700)]
Merge tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two recent regressions (ACPICA, the generic power domains
framework) and one crash that may happen on specific hardware
supported since 4.1 (intel_pstate).
Specifics:
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework that
may cause it to violate PM QoS latency constraints in some cases
(Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips that
do not update the MPERF counter as often as expected by the driver
which may result in a divide by 0 (Srinivas Pandruvada)"
* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
ACPICA: Tables: Fix FADT dependency regression
PM / Domains: Fix validation of latency constraints in genpd governor
Linus Torvalds [Fri, 16 Oct 2015 19:19:11 +0000 (12:19 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too crazy or exciting:
- two MAINTAINERS entries that I didn't see the point in delaying.
- one drm mst fix to stop sending uninitialised data to monitors
- two amdgpu fixes
- one radeon mst tiling fix
- one vmwgfx regression fix
- one virtio warning fix.
I have found one locking problem that needs a bit of reorg to fix, but
I'm not sure it's worth putting in -fixes as I don't think we've seen
it hit in the real world ever, I just found it using the virtio-gpu
driver when working on it. I'll possibly send it next week once I've
time to discuss with Daniel"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/virtio: use %llu format string form atomic64_t
MAINTAINERS: Add myself as maintainer for the gma500 driver
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
drm/dp/mst: make mst i2c transfer code more robust.
drm/radeon: attach tile property to mst connector
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
Linus Torvalds [Fri, 16 Oct 2015 19:07:43 +0000 (12:07 -0700)]
Merge tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
Linus Torvalds [Fri, 16 Oct 2015 18:42:37 +0000 (11:42 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
Andrew Morton [Thu, 15 Oct 2015 22:28:35 +0000 (15:28 -0700)]
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
lib/built-in.o: In function `__bitrev32':
deftree.c:(.text+0x1e799): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7a0): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7b4): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7c1): undefined reference to `byte_rev_table'
Anything which uses bitrevX() has to select BITREVERSE, to grab
lib/bitrev.o.
Reported-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Thu, 15 Oct 2015 22:28:32 +0000 (15:28 -0700)]
mm, dax: fix DAX deadlocks
The following two locking commits in the DAX code:
commit 843172978bb9 ("dax: fix race between simultaneous faults")
commit 46c043ede471 ("mm: take i_mmap_lock in unmap_mapping_range() for DAX")
introduced a number of deadlocks and other issues which need to be fixed
for the v4.3 kernel. The list of issues in DAX after these commits
(some newly introduced by the commits, some preexisting) can be found
here:
https://lkml.org/lkml/2015/9/25/602 (Subject: "Re: [PATCH] dax: fix deadlock in __dax_fault").
This undoes most of the changes introduced by those two commits,
essentially returning us to the DAX locking scheme that was used in
v4.2.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Dan Williams <dan.j.williams@intel.com> Tested-by: Dave Chinner <dchinner@redhat.com> Cc: Jan Kara <jack@suse.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Riku Voipio [Thu, 15 Oct 2015 22:28:26 +0000 (15:28 -0700)]
builddeb: remove debian/files before build
Commit 3716001bcb7f ("deb-pkg: add source package") added the ability to
create a debian changelog file. This exposed that previously the
builddeb script hasn't cleared debian/files between builds.
As debian/files keeps accumulating entries, the changes file will end up
growing indefinelty. With outdated entries in debian/files, builddeb
script will exit with failure. This regression impacts those who use
"make deb-pkg" target to build kernel into a .deb package and never use
"make mrproper" or other means to clean kernel tree from generated
directories.
To fix the regression, remove debian/files before starting build and in
the generated clean rule.
Fixes: 3716001bcb7f ("deb-pkg: add source package") Signed-off-by: Riku Voipio <riku.voipio@linaro.org> Reported-by: Doug Smythies <dsmythies@telus.net> Tested-by: Doug Smythies <dsmythies@telus.net> Tested-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Ben Hutchings <ben@decadent.org.uk> Cc: Michal Marek <mmarek@suse.cz> Cc: maximilian attems <maks@stro.at> Cc: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 15 Oct 2015 22:28:24 +0000 (15:28 -0700)]
mm, fs: obey gfp_mapping for add_to_page_cache()
Commit 6afdb859b710 ("mm: do not ignore mapping_gfp_mask in page cache
allocation paths") has caught some users of hardcoded GFP_KERNEL used in
the page cache allocation paths. This, however, wasn't complete and
there were others which went unnoticed.
Dave Chinner has reported the following deadlock for xfs on loop device:
: With the recent merge of the loop device changes, I'm now seeing
: XFS deadlock on my single CPU, 1GB RAM VM running xfs/073.
:
: The deadlocked is as follows:
:
: kloopd1: loop_queue_read_work
: xfs_file_iter_read
: lock XFS inode XFS_IOLOCK_SHARED (on image file)
: page cache read (GFP_KERNEL)
: radix tree alloc
: memory reclaim
: reclaim XFS inodes
: log force to unpin inodes
: <wait for log IO completion>
:
: xfs-cil/loop1: <does log force IO work>
: xlog_cil_push
: xlog_write
: <loop issuing log writes>
: xlog_state_get_iclog_space()
: <blocks due to all log buffers under write io>
: <waits for IO completion>
:
: kloopd1: loop_queue_write_work
: xfs_file_write_iter
: lock XFS inode XFS_IOLOCK_EXCL (on image file)
: <wait for inode to be unlocked>
:
: i.e. the kloopd, with it's split read and write work queues, has
: introduced a dependency through memory reclaim. i.e. that writes
: need to be able to progress for reads make progress.
:
: The problem, fundamentally, is that mpage_readpages() does a
: GFP_KERNEL allocation, rather than paying attention to the inode's
: mapping gfp mask, which is set to GFP_NOFS.
:
: The didn't used to happen, because the loop device used to issue
: reads through the splice path and that does:
:
: error = add_to_page_cache_lru(page, mapping, index,
: GFP_KERNEL & mapping_gfp_mask(mapping));
This has changed by commit aa4d86163e4 ("block: loop: switch to VFS
ITER_BVEC").
This patch changes mpage_readpage{s} to follow gfp mask set for the
mapping. There are, however, other places which are doing basically the
same.
lustre:ll_dir_filler is doing GFP_KERNEL from the function which
apparently uses GFP_NOFS for other allocations so let's make this
consistent.
cifs:readpages_get_pages is called from cifs_readpages and
__cifs_readpages_from_fscache called from the same path obeys mapping
gfp.
ramfs_nommu_expand_for_mapping is hardcoding GFP_KERNEL as well
regardless it uses mapping_gfp_mask for the page allocation.
ext4_mpage_readpages is the called from the page cache allocation path
same as read_pages and read_cache_pages
As I've noticed in my previous post I cannot say I would be happy about
sprinkling mapping_gfp_mask all over the place and it sounds like we
should drop gfp_mask argument altogether and use it internally in
__add_to_page_cache_locked that would require all the filesystems to use
mapping gfp consistently which I am not sure is the case here. From a
quick glance it seems that some file system use it all the time while
others are selective.
Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Dave Chinner <david@fromorbit.com> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: Ming Lei <ming.lei@canonical.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Oleg Drokin <oleg.drokin@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ilya Dryomov [Wed, 7 Oct 2015 15:27:17 +0000 (17:27 +0200)]
rbd: use writefull op for object size writes
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Ilya Dryomov [Wed, 7 Oct 2015 14:09:35 +0000 (16:09 +0200)]
rbd: set max_sectors explicitly
Commit 30e2bc08b2bb ("Revert "block: remove artifical max_hw_sectors
cap"") restored a clamp on max_sectors. It's now 2560 sectors instead
of 1024, but it's not good enough: we set max_hw_sectors to rbd object
size because we don't want object sized I/Os to be split, and the
default object size is 4M.
So, set max_sectors to max_hw_sectors in rbd at queue init time.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org>
Thomas Gleixner [Fri, 16 Oct 2015 13:50:22 +0000 (15:50 +0200)]
timekeeping: Increment clock_was_set_seq in timekeeping_init()
timekeeping_init() can set the wall time offset, so we need to
increment the clock_was_set_seq counter. That way hrtimers will pick
up the early offset immediately. Otherwise on a machine which does not
set wall time later in the boot process the hrtimer offset is stale at
0 and wall time timers are going to expire with a delay of 45 years.
Fixes: 868a3e915f7f "hrtimer: Make offset update smarter" Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Stefan Liebler <stli@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org>
Marc Zyngier [Tue, 13 Oct 2015 18:14:45 +0000 (19:14 +0100)]
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
When we create a generic MSI domain, that MSI_FLAG_USE_DEF_CHIP_OPS
is set, and that any of .mask or .unmask are NULL in the irq_chip
structure, we set them to pci_msi_[un]mask_irq.
This is a bad idea for at least two reasons:
- PCI_MSI might not be selected, kernel fails to build (yes, this is
legitimate, at least on arm64!)
- This may not be a PCI/MSI domain at all (platform MSI, for example)
Either way, this looks wrong. Move the overriding of mask/unmask to
the PCI counterpart, and panic is any of these two methods is not
set in the core code (they really should be present).
Andrej Ota [Wed, 14 Oct 2015 22:14:37 +0000 (00:14 +0200)]
via-rhine: fix VLAN receive handling regression.
Because eth_type_trans() consumes ethernet header worth of bytes, a call
to read TCI from end of packet using rhine_rx_vlan_tag() no longer works
as it's reading from an invalid offset.
Tested to be working on PCEngines Alix board.
Fixes: 810f19bcb862 ("via-rhine: add consistent memory barrier in vlan receive code.") Signed-off-by: Andrej Ota <andrej@ota.si> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Oct 2015 07:39:25 +0000 (00:39 -0700)]
Merge branch 'ipv6-blackhole-route-fix'
Martin KaFai Lau says:
====================
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
This patchset ensures the rt6_info's fields are initialized properly
in ip6_blackhole_route() where xfrm_policy is the primarily user.
The first patch is a prep work. The second patch is the fix. It
fixes d52d3997f843 ("ipv6: Create percpu rt6_info").
Here is the oops reported by Phil Sutter <phil@nwl.cc>:
Martin KaFai Lau [Thu, 15 Oct 2015 23:39:58 +0000 (16:39 -0700)]
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ip6_blackhole_route() does not initialize the newly allocated
rt6_info properly. This patch:
1. Call rt6_info_init() to initialize rt6i_siblings and rt6i_uncached
2. The current rt->dst._metrics init code is incorrect:
- 'rt->dst._metrics = ort->dst._metris' is not always safe
- Not sure what dst_copy_metrics() is trying to do here
considering ip6_rt_blackhole_cow_metrics() always returns
NULL
Fix:
- Always do dst_copy_metrics()
- Replace ip6_rt_blackhole_cow_metrics() with
dst_cow_metrics_generic()
3. Mask out the RTF_PCPU bit from the newly allocated blackhole route.
This bug triggers an oops (reported by Phil Sutter) in rt6_get_cookie().
It is because RTF_PCPU is set while rt->dst.from is NULL.
Fixes: d52d3997f843 ("ipv6: Create percpu rt6_info") Signed-off-by: Martin KaFai Lau <kafai@fb.com> Reported-by: Phil Sutter <phil@nwl.cc> Tested-by: Phil Sutter <phil@nwl.cc> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Julian Anastasov <ja@ssi.bg> Cc: Phil Sutter <phil@nwl.cc> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 15 Oct 2015 23:39:57 +0000 (16:39 -0700)]
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Introduce rt6_info_init() to do the common init work for
'struct rt6_info' (after calling dst_alloc).
It is a prep work to fix the rt6_info init logic in the
ip6_blackhole_route().
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Julian Anastasov <ja@ssi.bg> Cc: Phil Sutter <phil@nwl.cc> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg [Fri, 16 Oct 2015 07:07:53 +0000 (10:07 +0300)]
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
After clearing the params->explicit_connect variable the parameters
may need to be either added back to the right list or potentially left
absent from both the le_reports and the le_conns lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:52 +0000 (10:07 +0300)]
Bluetooth: Fix remove_device behavior for explicit connects
Devices undergoing an explicit connect should not have their
conn_params struct removed by the mgmt Remove Device command. This
patch fixes the necessary checks in the command handler to correct the
behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:51 +0000 (10:07 +0300)]
Bluetooth: Fix LE reconnection logic
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:50 +0000 (10:07 +0300)]
Bluetooth: Fix reference counting for LE-scan based connections
The code should never directly call hci_conn_hash_del since many
cleanup & reference counting updates would be lost. Normally
hci_conn_del is the right thing to do, but in the case of a connection
doing LE scanning this could cause a deadlock due to doing a
cancel_delayed_work_sync() on the same work callback that we were
called from.
Connections in the LE scanning state actually need very little cleanup
- just a small subset of hci_conn_del. To solve the issue, refactor
out these essential pieces into a new hci_conn_cleanup() function and
call that from the two necessary places.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jakub Pawlowski [Fri, 16 Oct 2015 07:07:49 +0000 (10:07 +0300)]
Bluetooth: Fix double scan updates
When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.
This patch makes sure that unnecessary scan disable/enable commands
are not issued.
When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.
hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.
When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Arnd Bergmann [Wed, 7 Oct 2015 10:41:21 +0000 (12:41 +0200)]
drm/virtio: use %llu format string form atomic64_t
The virtgpu driver prints the last_seq variable using the %ld or
%lu format string, which does not work correctly on all architectures
and causes this compiler warning on ARM:
drivers/gpu/drm/virtio/virtgpu_fence.c: In function 'virtio_timeline_value_str':
drivers/gpu/drm/virtio/virtgpu_fence.c:64:22: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'long long int' [-Wformat=]
snprintf(str, size, "%lu", atomic64_read(&fence->drv->last_seq));
^
drivers/gpu/drm/virtio/virtgpu_debugfs.c: In function 'virtio_gpu_debugfs_irq_info':
drivers/gpu/drm/virtio/virtgpu_debugfs.c:37:16: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'long long int' [-Wformat=]
seq_printf(m, "fence %ld %lld\n",
^
In order to avoid the warnings, this changes the format strings to %llu
and adds a cast to u64, which makes it work the same way everywhere.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Boris BREZILLON [Tue, 13 Oct 2015 09:55:42 +0000 (11:55 +0200)]
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
Add myself as the maintainer of the atmel-hlcdc DRM driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 15 Oct 2015 21:03:38 +0000 (14:03 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are a few more arm64 fixes for 4.3. Again, nothing too
significant, but worth having nonetheless. The MINSIGSTKSZ update is
a bit grotty, but the value we currently have is wrong (too small), so
anybody using that will have issues already. It has Arnd's ack for
the asm-generic change.
Summary:
- Fix module CFLAGS setting in workaround for erratum #843419
- Update MINSIGSTKSZ and SIGSTKSZ to match glibc
- Wire up some new compat syscalls"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: compat: wire up new syscalls
arm64: Fix MINSIGSTKSZ and SIGSTKSZ
arm64: errata: use KBUILD_CFLAGS_MODULE for erratum #843419
Linus Torvalds [Thu, 15 Oct 2015 20:58:22 +0000 (13:58 -0700)]
Merge tag 'pinctrl-v4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are some overdue (what can I say, I was on a short vacation)
driver fixes for the pin control subsystem:
- Allwinner sun5i A10s had a faulty mapping
- Freescale i.MX25 had some bad arithmetics
- Uniphier PH1-sLD8 missed some input enable settings"
* tag 'pinctrl-v4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: fix input enable settings for PH1-sLD8
pinctrl: imx25: ensure that a pin with id i is at position i in the info array
pinctrl: sun5i: Fix a10s pwm1 pinctrl mapping
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.
Fixes: b34ef932d79a (intel_pstate: Knights Landing support) Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Cc: 4.1+ <stable@vger.kernel.org> # 4.1+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 15 Oct 2015 20:44:35 +0000 (13:44 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"We have four batched up patches for the current rc kernel.
Two of them are small fixes that are obvious.
One of them is larger than I would like for a late stage rc pull, but
we found an issue in the namespace lookup code related to RoCE and
this works around the issue for now (we allow a lookup with a
namespace to succeed on RoCE since RoCE namespaces aren't implemented
yet). This will go away in 4.4 when we put in support for namespaces
in RoCE devices.
The last one is large in terms of lines, but is all legal and no
functional changes. Cisco needed to update their files to be more
specific about their license. They had intended the files to be dual
licensed as GPL/BSD all along, and specified that in their module
license tag, but their file headers were not up to par. They
contacted all of the contributors to get agreement and then submitted
a patch to update the license headers in the files.
Summary:
- Work around connection namespace lookup bug related to RoCE
- Change usnic license to Dual GPL/BSD (was intended to be that way
all along, but wasn't clear, permission from contributors was
chased down)
- Fix an issue between NFSoRDMA and mlx5 that could cause an oops
- Fix leak of sendonly multicast groups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: For sendonly join free the multicast group on leave
IB/cma: Accept connection without a valid netdev on RoCE
xprtrdma: Don't require LOCAL_DMA_LKEY support for fastreg
usnic: add missing clauses to BSD license
projects / linux-beck.git / log