Tony Lindgren [Tue, 20 Oct 2015 17:29:27 +0000 (10:29 -0700)]
Merge tag 'omap-for-v4.4/dt-pt2' into for-next
Few more omap dts changes for v4.4 merge window, mostly to fix and clean
up some omap5 issues to allow adding other omap5 boards. Also some other
fixes and clean-up:
- Fix SDIO WLAN for omap5 that's been broken for a while. As further
patches are still needed for wl18xx, no need for stable on this one.
- Move most of omap5 support into omap5-board-common.dtsi as most omap5
boards seem to share the same basic set of devices.
- Add minimal IGEPv5 support using based on omap5-board-common.dtsi
- Remove now unneedes gpio hogging for dra72-evm
- Update Javier Martinez Canillas email address
- Change earlier IGEP boards to use IOPAD pinmux macros
Use the AM33XX pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the AM33xx pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the OMAP3 pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Vignesh R [Wed, 14 Oct 2015 13:54:25 +0000 (19:24 +0530)]
ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts
On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power
state via pinctrl and IO daisy chain using generic wakeirq framework.
With commit 3fffd1283927 ("i2c: allow specifying separate wakeup
interrupt in device tree") i2c core allows optional wakeirq to be
specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts
to wake the system from low power state.
Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
I see that people are still sending emails to my old address (that no
longer exists) since is the one mentioned in the IGEP DTS. Replace it
with my current email address to avoid this.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Mon, 21 Sep 2015 14:53:51 +0000 (20:23 +0530)]
ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios
With the current implementation of GPIO hogging and with
gpio-pcf857x is built as module, ethernet doesn't work on boot
and doesn't throw any error/warning to user. Ethernet becomes
operational when inserting gpio-pcf857x module, even this time
there is no error/warning logs to user that ethernet is
operational.
When using with NFS rootfs and gpio-pcf857x as module, board
doesn't boot as it doesn't get any ip address and doesn't throw
any error/warning. To over come this, now cpsw driver tries to
get mode-gpios. When gpio-pcf857x is built as module it will
throw error, so that user can decide either to built in
gpio-pcf857x to continue with nfs boot or choose alternate rootfs
filesystem like sd/ramdisk.
When using mmc/ramdisk as root fs, cpsw will probe defer and
re-probes again when gpio-pcf857x module is inserted and ethernet
becomes operational.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Some omaps are producing imprecise external aborts because we are
wrongly trying to init SRAM for device tree based booting. Only
omap3 is still using the legacy SRAM code, so we need to make it
omap3 specific. Otherwise we can get errors like this on at least
dm814x:
Unhandled fault: imprecise external abort (0xc06) at 0xc08b156c
...
(omap_rev) from [<c08b12e0>] (omap_sram_init+0xf8/0x3e0)
(omap_sram_init) from [<c08aca0c>] (omap_sdrc_init+0x10/0xb0)
(omap_sdrc_init) from [<c08b581c>] (pdata_quirks_init+0x18/0x44)
(pdata_quirks_init) from [<c08b5478>] (omap_generic_init+0x10/0x1c)
(omap_generic_init) from [<c08a57e0>] (customize_machine+0x1c/0x40)
(customize_machine) from [<c00098a4>] (do_one_initcall+0x80/0x1dc)
(do_one_initcall) from [<c08a2ec4>] (kernel_init_freeable+0x218/0x2e8)
(kernel_init_freeable) from [<c063a554>] (kernel_init+0x8/0xec)
(kernel_init) from [<c000f890>] (ret_from_fork+0x14/0x24)
Let's fix the issue by making sure omap_sdrc_init only gets called for
omap3. To do that, we need to have compatible "ti,omap3" in the dts
files. And let's also use "ti,omap3630" instead of "ti,omap36xx" like
we're supposed to.
Linus Torvalds [Sun, 18 Oct 2015 19:07:48 +0000 (12:07 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes for the I2C subsystem.
Kieran found a flaw in the recently renewed wake irq handling. Mika
handled a user bug report where the ACPI info turned out to be
unusable. I updated MAINTAINERS so that such bug reports will sooner
get to the right people. Geert pointed me to a problem of some i2c
drivers regarding PM which I fixed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
i2c: designware-platdrv: enable RuntimePM before registering to the core
i2c: s3c2410: enable RuntimePM before registering to the core
i2c: rcar: enable RuntimePM before registering to the core
i2c: return probe deferred status on dev_pm_domain_attach
Mika Westerberg [Thu, 24 Sep 2015 09:06:54 +0000 (12:06 +0300)]
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Linus Torvalds [Sat, 17 Oct 2015 00:39:27 +0000 (17:39 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
Linus Torvalds [Sat, 17 Oct 2015 00:11:14 +0000 (17:11 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"Just one revert for Armada XP devices: the conversion to
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name().
We could make of_clk_get_parent_name() more robust, but that
may have unintended side-effects, so we'll do that in the
next version"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
Linus Torvalds [Fri, 16 Oct 2015 20:03:05 +0000 (13:03 -0700)]
Merge tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two DM target error path cleanup fixes (one for stable in DM thinp and
one for a v4.3-rc5 thinko in DM snapshot)"
* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix missing pool reference count decrement in pool_ctr error path
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
Linus Torvalds [Fri, 16 Oct 2015 19:55:34 +0000 (12:55 -0700)]
Merge branch 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I have two more bug fixes for btrfs.
My commit fixes a bug we hit last week at FB, a combination of lots of
hard links and an admin command to resolve inode numbers.
Dave is adding checks to make sure balance on current kernels ignores
filters it doesn't understand. The penalty for being wrong is just
doing more work (not crashing etc), but it's a good fix"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix use after free iterating extrefs
btrfs: check unsupported filters in balance arguments
Linus Torvalds [Fri, 16 Oct 2015 19:47:02 +0000 (12:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
Tony Lindgren [Fri, 16 Oct 2015 19:32:33 +0000 (12:32 -0700)]
ARM: dts: Add basic support for isee igepv5
With omap5-board-common.dtsi, we can now easily add support for various omap5
board variants. Let's add minimal support for isee igepv5.
So far I've tested that basic things work, such as serial, USB Ethernet, HDMI
and WLAN.
Note that like omap5-uevm, these boards seem to need to reserve 16MB for a
trap section as in commit 03178c66d289 ("ARM: dts: omap5-evm: Update
available memory to 2032 MB") and also noted in a u-boot commit at
http://marc.info/?l=u-boot&m=134376852603255 and also at
http://patchwork.ozlabs.org/patch/159881/.
Not sure why this is not needed for omap5-cm-t54.dts, maybe because of
different u-boot configuration.
Tony Lindgren [Fri, 16 Oct 2015 19:32:32 +0000 (12:32 -0700)]
ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi
Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's
create omap5-board-common.dtsi to allow fixing up things properly for mainline
kernel to support all these.
Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA +
USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest
way to add support for other boards rather than diffing various versions of
out of tree dts files.
My guess is that also omap5-sbc-t54.dts can use this, but I don't have that
board so that will need to be dealt with later on.
Tony Lindgren [Fri, 16 Oct 2015 19:32:32 +0000 (12:32 -0700)]
ARM: dts: Fix WLAN regression on omap5-uevm
Commit 99f84cae43df ("ARM: dts: add wl12xx/wl18xx bindings") added
device tree bindings for the TI WLAN SDIO on many omap variants.
I recall wondering how come omap5-uevm did not have the WLAN
added and this issue has been bugging me for a while now, and
I finally tracked it down to a bad pinmux regression, and a missing
deferred probe handling for the 32k clock from palmas that's
requested by twl6040.
Basically 392adaf796b9 ("ARM: dts: omap5-evm: Add mcspi data")
added pin muxing for mcspi4 that conflicts with the onboard
WLAN. While some omap5-uevm don't have WLAN populated, the
pins are not reused for other devices. And as the SDIO bus
should be probed, let's try to enable WLAN by default.
Let's fix the regression and add the WLAN configuration as
done for the other boards in 99f84cae43df ("ARM: dts: add
wl12xx/wl18xx bindings"). And let's use the new MMC pwrseq for
the 32k clock as suggested by Javier Martinez Canillas
<javier@dowhile0.org>.
Note that without a related deferred probe fix for twl6040,
the 32k clock is not initialized if palmas-clk is a module
and twl6040 is built-in.
Let's also use the generic "non-removable" instead of the
legacy "ti,non-removable" property while at it.
And finally, note that omap5 seems to require WAKEUP_EN for
the WLAN GPIO interrupt.
Linus Torvalds [Fri, 16 Oct 2015 19:25:54 +0000 (12:25 -0700)]
Merge tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two recent regressions (ACPICA, the generic power domains
framework) and one crash that may happen on specific hardware
supported since 4.1 (intel_pstate).
Specifics:
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework that
may cause it to violate PM QoS latency constraints in some cases
(Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips that
do not update the MPERF counter as often as expected by the driver
which may result in a divide by 0 (Srinivas Pandruvada)"
* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
ACPICA: Tables: Fix FADT dependency regression
PM / Domains: Fix validation of latency constraints in genpd governor
Linus Torvalds [Fri, 16 Oct 2015 19:19:11 +0000 (12:19 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too crazy or exciting:
- two MAINTAINERS entries that I didn't see the point in delaying.
- one drm mst fix to stop sending uninitialised data to monitors
- two amdgpu fixes
- one radeon mst tiling fix
- one vmwgfx regression fix
- one virtio warning fix.
I have found one locking problem that needs a bit of reorg to fix, but
I'm not sure it's worth putting in -fixes as I don't think we've seen
it hit in the real world ever, I just found it using the virtio-gpu
driver when working on it. I'll possibly send it next week once I've
time to discuss with Daniel"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/virtio: use %llu format string form atomic64_t
MAINTAINERS: Add myself as maintainer for the gma500 driver
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
drm/dp/mst: make mst i2c transfer code more robust.
drm/radeon: attach tile property to mst connector
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
Tony Lindgren [Fri, 16 Oct 2015 19:16:21 +0000 (12:16 -0700)]
ARM: OMAP2+: Fix oops with LPAE and more than 2GB of memory
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384() 44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Fri, 16 Oct 2015 19:07:43 +0000 (12:07 -0700)]
Merge tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
Linus Torvalds [Fri, 16 Oct 2015 18:42:37 +0000 (11:42 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
Andrew Morton [Thu, 15 Oct 2015 22:28:35 +0000 (15:28 -0700)]
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
lib/built-in.o: In function `__bitrev32':
deftree.c:(.text+0x1e799): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7a0): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7b4): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7c1): undefined reference to `byte_rev_table'
Anything which uses bitrevX() has to select BITREVERSE, to grab
lib/bitrev.o.
Reported-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Thu, 15 Oct 2015 22:28:32 +0000 (15:28 -0700)]
mm, dax: fix DAX deadlocks
The following two locking commits in the DAX code:
commit 843172978bb9 ("dax: fix race between simultaneous faults")
commit 46c043ede471 ("mm: take i_mmap_lock in unmap_mapping_range() for DAX")
introduced a number of deadlocks and other issues which need to be fixed
for the v4.3 kernel. The list of issues in DAX after these commits
(some newly introduced by the commits, some preexisting) can be found
here:
https://lkml.org/lkml/2015/9/25/602 (Subject: "Re: [PATCH] dax: fix deadlock in __dax_fault").
This undoes most of the changes introduced by those two commits,
essentially returning us to the DAX locking scheme that was used in
v4.2.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Dan Williams <dan.j.williams@intel.com> Tested-by: Dave Chinner <dchinner@redhat.com> Cc: Jan Kara <jack@suse.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Riku Voipio [Thu, 15 Oct 2015 22:28:26 +0000 (15:28 -0700)]
builddeb: remove debian/files before build
Commit 3716001bcb7f ("deb-pkg: add source package") added the ability to
create a debian changelog file. This exposed that previously the
builddeb script hasn't cleared debian/files between builds.
As debian/files keeps accumulating entries, the changes file will end up
growing indefinelty. With outdated entries in debian/files, builddeb
script will exit with failure. This regression impacts those who use
"make deb-pkg" target to build kernel into a .deb package and never use
"make mrproper" or other means to clean kernel tree from generated
directories.
To fix the regression, remove debian/files before starting build and in
the generated clean rule.
Fixes: 3716001bcb7f ("deb-pkg: add source package") Signed-off-by: Riku Voipio <riku.voipio@linaro.org> Reported-by: Doug Smythies <dsmythies@telus.net> Tested-by: Doug Smythies <dsmythies@telus.net> Tested-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Ben Hutchings <ben@decadent.org.uk> Cc: Michal Marek <mmarek@suse.cz> Cc: maximilian attems <maks@stro.at> Cc: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 15 Oct 2015 22:28:24 +0000 (15:28 -0700)]
mm, fs: obey gfp_mapping for add_to_page_cache()
Commit 6afdb859b710 ("mm: do not ignore mapping_gfp_mask in page cache
allocation paths") has caught some users of hardcoded GFP_KERNEL used in
the page cache allocation paths. This, however, wasn't complete and
there were others which went unnoticed.
Dave Chinner has reported the following deadlock for xfs on loop device:
: With the recent merge of the loop device changes, I'm now seeing
: XFS deadlock on my single CPU, 1GB RAM VM running xfs/073.
:
: The deadlocked is as follows:
:
: kloopd1: loop_queue_read_work
: xfs_file_iter_read
: lock XFS inode XFS_IOLOCK_SHARED (on image file)
: page cache read (GFP_KERNEL)
: radix tree alloc
: memory reclaim
: reclaim XFS inodes
: log force to unpin inodes
: <wait for log IO completion>
:
: xfs-cil/loop1: <does log force IO work>
: xlog_cil_push
: xlog_write
: <loop issuing log writes>
: xlog_state_get_iclog_space()
: <blocks due to all log buffers under write io>
: <waits for IO completion>
:
: kloopd1: loop_queue_write_work
: xfs_file_write_iter
: lock XFS inode XFS_IOLOCK_EXCL (on image file)
: <wait for inode to be unlocked>
:
: i.e. the kloopd, with it's split read and write work queues, has
: introduced a dependency through memory reclaim. i.e. that writes
: need to be able to progress for reads make progress.
:
: The problem, fundamentally, is that mpage_readpages() does a
: GFP_KERNEL allocation, rather than paying attention to the inode's
: mapping gfp mask, which is set to GFP_NOFS.
:
: The didn't used to happen, because the loop device used to issue
: reads through the splice path and that does:
:
: error = add_to_page_cache_lru(page, mapping, index,
: GFP_KERNEL & mapping_gfp_mask(mapping));
This has changed by commit aa4d86163e4 ("block: loop: switch to VFS
ITER_BVEC").
This patch changes mpage_readpage{s} to follow gfp mask set for the
mapping. There are, however, other places which are doing basically the
same.
lustre:ll_dir_filler is doing GFP_KERNEL from the function which
apparently uses GFP_NOFS for other allocations so let's make this
consistent.
cifs:readpages_get_pages is called from cifs_readpages and
__cifs_readpages_from_fscache called from the same path obeys mapping
gfp.
ramfs_nommu_expand_for_mapping is hardcoding GFP_KERNEL as well
regardless it uses mapping_gfp_mask for the page allocation.
ext4_mpage_readpages is the called from the page cache allocation path
same as read_pages and read_cache_pages
As I've noticed in my previous post I cannot say I would be happy about
sprinkling mapping_gfp_mask all over the place and it sounds like we
should drop gfp_mask argument altogether and use it internally in
__add_to_page_cache_locked that would require all the filesystems to use
mapping gfp consistently which I am not sure is the case here. From a
quick glance it seems that some file system use it all the time while
others are selective.
Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Dave Chinner <david@fromorbit.com> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: Ming Lei <ming.lei@canonical.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Oleg Drokin <oleg.drokin@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ilya Dryomov [Wed, 7 Oct 2015 15:27:17 +0000 (17:27 +0200)]
rbd: use writefull op for object size writes
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Ilya Dryomov [Wed, 7 Oct 2015 14:09:35 +0000 (16:09 +0200)]
rbd: set max_sectors explicitly
Commit 30e2bc08b2bb ("Revert "block: remove artifical max_hw_sectors
cap"") restored a clamp on max_sectors. It's now 2560 sectors instead
of 1024, but it's not good enough: we set max_hw_sectors to rbd object
size because we don't want object sized I/Os to be split, and the
default object size is 4M.
So, set max_sectors to max_hw_sectors in rbd at queue init time.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org>
Thomas Gleixner [Fri, 16 Oct 2015 13:50:22 +0000 (15:50 +0200)]
timekeeping: Increment clock_was_set_seq in timekeeping_init()
timekeeping_init() can set the wall time offset, so we need to
increment the clock_was_set_seq counter. That way hrtimers will pick
up the early offset immediately. Otherwise on a machine which does not
set wall time later in the boot process the hrtimer offset is stale at
0 and wall time timers are going to expire with a delay of 45 years.
Fixes: 868a3e915f7f "hrtimer: Make offset update smarter" Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Stefan Liebler <stli@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org>
Marc Zyngier [Tue, 13 Oct 2015 18:14:45 +0000 (19:14 +0100)]
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
When we create a generic MSI domain, that MSI_FLAG_USE_DEF_CHIP_OPS
is set, and that any of .mask or .unmask are NULL in the irq_chip
structure, we set them to pci_msi_[un]mask_irq.
This is a bad idea for at least two reasons:
- PCI_MSI might not be selected, kernel fails to build (yes, this is
legitimate, at least on arm64!)
- This may not be a PCI/MSI domain at all (platform MSI, for example)
Either way, this looks wrong. Move the overriding of mask/unmask to
the PCI counterpart, and panic is any of these two methods is not
set in the core code (they really should be present).
Arnd Bergmann [Wed, 7 Oct 2015 10:41:21 +0000 (12:41 +0200)]
drm/virtio: use %llu format string form atomic64_t
The virtgpu driver prints the last_seq variable using the %ld or
%lu format string, which does not work correctly on all architectures
and causes this compiler warning on ARM:
drivers/gpu/drm/virtio/virtgpu_fence.c: In function 'virtio_timeline_value_str':
drivers/gpu/drm/virtio/virtgpu_fence.c:64:22: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'long long int' [-Wformat=]
snprintf(str, size, "%lu", atomic64_read(&fence->drv->last_seq));
^
drivers/gpu/drm/virtio/virtgpu_debugfs.c: In function 'virtio_gpu_debugfs_irq_info':
drivers/gpu/drm/virtio/virtgpu_debugfs.c:37:16: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'long long int' [-Wformat=]
seq_printf(m, "fence %ld %lld\n",
^
In order to avoid the warnings, this changes the format strings to %llu
and adds a cast to u64, which makes it work the same way everywhere.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Boris BREZILLON [Tue, 13 Oct 2015 09:55:42 +0000 (11:55 +0200)]
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
Add myself as the maintainer of the atmel-hlcdc DRM driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 15 Oct 2015 21:03:38 +0000 (14:03 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are a few more arm64 fixes for 4.3. Again, nothing too
significant, but worth having nonetheless. The MINSIGSTKSZ update is
a bit grotty, but the value we currently have is wrong (too small), so
anybody using that will have issues already. It has Arnd's ack for
the asm-generic change.
Summary:
- Fix module CFLAGS setting in workaround for erratum #843419
- Update MINSIGSTKSZ and SIGSTKSZ to match glibc
- Wire up some new compat syscalls"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: compat: wire up new syscalls
arm64: Fix MINSIGSTKSZ and SIGSTKSZ
arm64: errata: use KBUILD_CFLAGS_MODULE for erratum #843419
Linus Torvalds [Thu, 15 Oct 2015 20:58:22 +0000 (13:58 -0700)]
Merge tag 'pinctrl-v4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are some overdue (what can I say, I was on a short vacation)
driver fixes for the pin control subsystem:
- Allwinner sun5i A10s had a faulty mapping
- Freescale i.MX25 had some bad arithmetics
- Uniphier PH1-sLD8 missed some input enable settings"
* tag 'pinctrl-v4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: fix input enable settings for PH1-sLD8
pinctrl: imx25: ensure that a pin with id i is at position i in the info array
pinctrl: sun5i: Fix a10s pwm1 pinctrl mapping
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.
Fixes: b34ef932d79a (intel_pstate: Knights Landing support) Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Cc: 4.1+ <stable@vger.kernel.org> # 4.1+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 15 Oct 2015 20:44:35 +0000 (13:44 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"We have four batched up patches for the current rc kernel.
Two of them are small fixes that are obvious.
One of them is larger than I would like for a late stage rc pull, but
we found an issue in the namespace lookup code related to RoCE and
this works around the issue for now (we allow a lookup with a
namespace to succeed on RoCE since RoCE namespaces aren't implemented
yet). This will go away in 4.4 when we put in support for namespaces
in RoCE devices.
The last one is large in terms of lines, but is all legal and no
functional changes. Cisco needed to update their files to be more
specific about their license. They had intended the files to be dual
licensed as GPL/BSD all along, and specified that in their module
license tag, but their file headers were not up to par. They
contacted all of the contributors to get agreement and then submitted
a patch to update the license headers in the files.
Summary:
- Work around connection namespace lookup bug related to RoCE
- Change usnic license to Dual GPL/BSD (was intended to be that way
all along, but wasn't clear, permission from contributors was
chased down)
- Fix an issue between NFSoRDMA and mlx5 that could cause an oops
- Fix leak of sendonly multicast groups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: For sendonly join free the multicast group on leave
IB/cma: Accept connection without a valid netdev on RoCE
xprtrdma: Don't require LOCAL_DMA_LKEY support for fastreg
usnic: add missing clauses to BSD license
Linus Torvalds [Thu, 15 Oct 2015 20:01:50 +0000 (13:01 -0700)]
vmstat: explicitly schedule per-cpu work on the CPU we need it to run on
The vmstat code uses "schedule_delayed_work_on()" to do the initial
startup of the delayed work on the right CPU, but then once it was
started it would use the non-cpu-specific "schedule_delayed_work()" to
re-schedule it on that CPU.
That just happened to schedule it on the same CPU historically (well, in
almost all situations), but the code _requires_ this work to be per-cpu,
and should say so explicitly rather than depend on the non-cpu-specific
scheduling to schedule on the current CPU.
The timer code is being changed to not be as single-minded in always
running things on the calling CPU.
See also commit 874bbfe600a6 ("workqueue: make sure delayed work run in
local cpu") that for now maintains the local CPU guarantees just in case
there are other broken users that depended on the accidental behavior.
Linus Torvalds [Thu, 15 Oct 2015 19:58:37 +0000 (12:58 -0700)]
Merge branch 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixlet from Tejun Heo:
"Single patch to make delayed work always be queued on the local CPU"
This is not actually something we should guarantee, but it's something
we by accident have historically done, and at least one call site has
grown to depend on it.
I'm going to fix that known broken callsite, but in the meantime this
makes the accidental behavior be explicit, just in case there are other
cases that might depend on it.
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure delayed work run in local cpu
Wolfram Sang [Thu, 15 Oct 2015 13:50:15 +0000 (15:50 +0200)]
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
Those guys already have been helpful in the past and are actively
working on this driver, unlike me.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Michel Dänzer [Thu, 8 Oct 2015 08:48:04 +0000 (17:48 +0900)]
drm/amdgpu: Keep the pflip interrupts always enabled v7
This fixes flickering issues caused by prematurely firing pflip
interrupts.
v2 (chk): add commit message, fix DCE V10/V11 and DM as well
v3: Re-enable pflip interrupt wherever we re-enable a CRTC
v4: Enable pflip interrupt in DAL as well
v5: drop DAL changes for upstream
v6: (agd): only enable interrupts on crtcs that exist
v7: (agd): integrate suggestions from Michel
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Wolfram Sang [Fri, 9 Oct 2015 09:39:24 +0000 (10:39 +0100)]
i2c: designware-platdrv: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@kernel.org
Wolfram Sang [Sat, 10 Oct 2015 07:24:23 +0000 (08:24 +0100)]
i2c: s3c2410: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Kukjin Kim <kgene@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Wolfram Sang [Fri, 9 Oct 2015 09:39:25 +0000 (10:39 +0100)]
i2c: rcar: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Lv Zheng [Wed, 14 Oct 2015 05:53:57 +0000 (13:53 +0800)]
ACPICA: Tables: Fix FADT dependency regression
Some logics actually relying on the existence of FADT, currently relies on
the number of loaded tables. This false dependency can easily trigger
regressions. One of them has been introduced by commit 8ec3f459073e
(ACPICA: Tables: Fix global table list issues by removing fixed table).
The commit changing the fixed table indexes results in the change of FADT
table index, originally, it was 3 (thus the installed table count should be
greater than 4), while currently it is 0 (and the installed table count may
be 3).
This patch fixes this regression by cleaning up the code. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=105351 Fixes: 8ec3f459073e (ACPICA: Tables: Fix global table list issues by removing fixed table) Reported-and-tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Thomas reports that it causes regressions on Armada XP devices.
This is because of_clk_get_parent_name() relies on the property
'clock-output-names' to resolve the name of a clock's parent,
without trying to get the clock from the framework and call
__clk_get_name(). Given that Armada XP devices don't have the
'clock-output-names' property, of_clk_get_parent_name() returns
the name of the node which doesn't match the actual parent
clock's name at all, causing CPU clocks to never link up with
their parents.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Linus Torvalds [Wed, 14 Oct 2015 16:47:38 +0000 (09:47 -0700)]
Merge tag 'mfd-fixes-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Bug Fixes:
- Return correct error code i.e. not zero
- Fix build error when !CONFIG_PM_SLEEP"
* tag 'mfd-fixes-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: max77843: Fix max77843_chg_init() return on error
mfd: intel-lpss: Fix build error when !CONFIG_PM_SLEEP
Paolo Bonzini [Wed, 14 Oct 2015 13:25:52 +0000 (15:25 +0200)]
KVM: x86: fix RSM into 64-bit protected mode
In order to get into 64-bit protected mode, you need to enable
paging while EFER.LMA=1. For this to work, CS.L must be 0.
Currently, we load the segments before CR0 and CR4, which means
that if RSM returns into 64-bit protected mode CS.L is already 1
and everything breaks.
Luckily, CS.L=0 is always the case when executing RSM, because it
is forbidden to execute RSM from 64-bit protected mode. Hence it
is enough to load CR0 and CR4 first, and only then the segments.
Fixes: 660a5d517aaab9187f93854425c4c63f4a09195c Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Will Deacon [Wed, 14 Oct 2015 12:20:36 +0000 (13:20 +0100)]
arm64: compat: wire up new syscalls
Commit 208473c1f3ac ("ARM: wire up new syscalls") hooked up the new
userfaultfd and membarrier syscalls for ARM, so do the same for our
compat syscall table in arm64.
Chris Mason [Tue, 13 Oct 2015 18:06:48 +0000 (14:06 -0400)]
btrfs: fix use after free iterating extrefs
The code for btrfs inode-resolve has never worked properly for
files with enough hard links to trigger extrefs. It was trying to
get the leaf out of a path after freeing the path:
The fix here is to use the extent buffer we cloned just a little higher
up to avoid deadlocks caused by using the leaf in the path.
Signed-off-by: Chris Mason <clm@fb.com>
cc: stable@vger.kernel.org # v3.7+
cc: Mark Fasheh <mfasheh@suse.de> Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Mark Fasheh <mfasheh@suse.de>
David Sterba [Mon, 12 Oct 2015 14:55:54 +0000 (16:55 +0200)]
btrfs: check unsupported filters in balance arguments
We don't verify that all the balance filter arguments supplemented by
the flags are actually known to the kernel. Thus we let it silently pass
and do nothing.
At the moment this means only the 'limit' filter, but we're going to add
a few more soon so it's better to have that fixed. Also in older stable
kernels so that it works with newer userspace tools.
Cc: stable@vger.kernel.org # 3.16+ Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Chris Mason <clm@fb.com>
Ulf Hansson [Tue, 13 Oct 2015 14:10:28 +0000 (16:10 +0200)]
PM / Domains: Fix validation of latency constraints in genpd governor
Commit ba2bbfbf6307 (PM / Domains: Remove intermediate states from the
power off sequence) changed the power off sequence in genpd. That also
required some updates regarding the validation of latency constraints in
the genpd governor. Unfortunate that wasn't covered, so let's fix this.
From a runtime PM and latency point of view, we need to consider the worst
case scenario while validating latency constraints. That's typically when
a call to pm_runtime_get_sync() needs to wait for a ongoing runtime
suspend operation to be carried out, as it then also needs to wait for the
device to be runtime resumed again.
The above mentioned commit made the genpd governor's ->stop_ok() callback
responsible of validating genpd's device's runtime suspend/resume latency.
In other words, the constraint needs to be validated towards the relevant
latencies present in genpd's ->runtime_suspend|resume() callbacks.
Earlier, that included latencies from the ->stop|start() callbacks, but as
->save|restore_state() are now also being invoked from genpd's
->runtime_suspend|resume() and to comply with the worst case scenario,
let's take also those latencies into account.
Fixes: ba2bbfbf6307 (PM / Domains: Remove intermediate states from the power off sequence) Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
IB/ipoib: For sendonly join free the multicast group on leave
When we leave the multicast group on expiration of a neighbor we
do not free the mcast structure. This results in a memory leak
that causes ib_dealloc_pd to fail and print a WARN_ON message
and backtrace.
Linus Torvalds [Tue, 13 Oct 2015 18:31:03 +0000 (11:31 -0700)]
Merge tag 'nfsd-4.3-2' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Two nfsd fixes, one for an RDMA crash, one for a pnfs/block protocol
bug"
* tag 'nfsd-4.3-2' of git://linux-nfs.org/~bfields/linux:
svcrdma: Fix NFS server crash triggered by 1MB NFS WRITE
nfsd/blocklayout: accept any minlength
Linus Torvalds [Tue, 13 Oct 2015 17:09:59 +0000 (10:09 -0700)]
Merge tag 'iommu-fixes-v4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"A few fixes piled up:
- Fix for a suspend/resume issue where PCI probing code overwrote
dev->irq for the MSI irq of the AMD IOMMU.
- Fix for a kernel crash when a 32 bit PCI device was assigned to a
KVM guest.
- Fix for a possible memory leak in the VT-d driver
- A couple of fixes for the ARM-SMMU driver"
* tag 'iommu-fixes-v4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix NULL pointer deref on device detach
iommu/amd: Prevent binding other PCI drivers to IOMMU PCI devices
iommu/vt-d: Fix memory leak in dmar_insert_one_dev_info()
iommu/arm-smmu: Use correct address mask for CMD_TLBI_S2_IPA
iommu/arm-smmu: Ensure IAS is set correctly for AArch32-capable SMMUs
iommu/io-pgtable-arm: Don't use dma_to_phys()
Linus Torvalds [Tue, 13 Oct 2015 16:45:21 +0000 (09:45 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I got a bit behind last week, so here is a delayed fixes pull:
- a bunch of radeon/amd gpu fixes
- some nouveau regression fixes (ppc bios reading and runtime pm fix)
- one drm core oops fix
- two qxl locking fixes
- one qxl regression fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/bios: fix OF loading
drm/nouveau/fbcon: take runpm reference when userspace has an open fd
drm/nouveau/nouveau: Disable AGP for SiS 761
drm/nouveau/display: allow up to 16k width/height for fermi+
drm/nouveau/bios: translate devinit pri/sec i2c bus to internal identifiers
drm: Fix locking for sysfs dpms file
drm/amdgpu: fix memory leak in amdgpu_vm_update_page_directory
drm/amdgpu: fix 32-bit compiler warning
drm/qxl: avoid dependency lock
drm/qxl: avoid buffer reservation in qxl_crtc_page_flip
drm/qxl: fix framebuffer dirty rectangle tracking.
drm/amdgpu: flag iceland as experimental
drm/amdgpu: check before checking pci bridge registers
drm/amdgpu: fix num_crtc on CZ
drm/amdgpu: restore the fbdev mode in lastclose
drm/radeon: restore the fbdev mode in lastclose
drm/radeon: add quirk for ASUS R7 370
drm/amdgpu: add pm sysfs files late
drm/radeon: add pm sysfs files late
Paolo Bonzini [Mon, 12 Oct 2015 11:56:27 +0000 (13:56 +0200)]
KVM: x86: map/unmap private slots in __x86_set_memory_region
Otherwise, two copies (one of them never populated and thus bogus)
are allocated for the regular and SMM address spaces. This breaks
SMM with EPT but without unrestricted guest support, because the
SMM copy of the identity page map is all zeros.
By moving the allocation to the caller we also remove the last
vestiges of kernel-allocated memory regions (not accessible anymore
in userspace since commit b74a07beed0e, "KVM: Remove kernel-allocated
memory regions", 2010-06-21); that is a nice bonus.
Paolo Bonzini [Mon, 12 Oct 2015 11:38:32 +0000 (13:38 +0200)]
KVM: x86: build kvm_userspace_memory_region in x86_set_memory_region
The next patch will make x86_set_memory_region fill the
userspace_addr. Since the struct is not used untouched
anymore, it makes sense to build it in x86_set_memory_region
directly; it also simplifies the callers.
Sudip Mukherjee [Tue, 13 Oct 2015 08:03:08 +0000 (13:33 +0530)]
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
If an unsupported option is given then the early return from
persistent_ctr() leaked memory allocated for the 'pstore' and never
destroyed the 'metadata_wq'.
Fixes: b0d3cc011e53 ("dm snapshot: add new persistent store option to support overflow") Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Russell King [Fri, 9 Oct 2015 19:43:33 +0000 (20:43 +0100)]
crypto: ahash - ensure statesize is non-zero
Unlike shash algorithms, ahash drivers must implement export
and import as their descriptors may contain hardware state and
cannot be exported as is. Unfortunately some ahash drivers did
not provide them and end up causing crashes with algif_hash.
This patch adds a check to prevent these drivers from registering
ahash algorithms until they are fixed.
Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thomas Hellstrom [Mon, 12 Oct 2015 08:49:39 +0000 (01:49 -0700)]
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
The commit "drm/vmwgfx: Fix up user_dmabuf refcounting", while fixing a
kernel crash introduced a NULL pointer dereference on older hardware.
Fix this.
Cc: <stable@vger.kernel.org> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com>
Michael Ellerman [Mon, 12 Oct 2015 04:28:57 +0000 (15:28 +1100)]
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
Commit 7a5692e6e533 ("arch/powerpc: provide zero_bytemask() for
big-endian") added a call to __fls() in our word-at-a-time.h. That was
fine for the kernel build but missed the fact that we also use
word-at-a-time.h in a userspace test.
Pulling in the kernel version of __fls() gets messy, so just define our
own, it's unlikely to change often.
Fixes: 7a5692e6e533 ("arch/powerpc: provide zero_bytemask() for big-endian") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mugunthan V N [Mon, 12 Oct 2015 09:07:12 +0000 (14:37 +0530)]
ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA74x, DRA72x and AM57xx EVMs the card detect gpio is
designed as active low gpio. So correcting the dt card detect
gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Mon, 12 Oct 2015 09:07:11 +0000 (14:37 +0530)]
ARM: dts: am43xx: fix cd-gpios definition as per hardware design and dt binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Mon, 12 Oct 2015 09:07:10 +0000 (14:37 +0530)]
ARM: dts: am335x: fix cd-gpios definition as per hardware design and dt binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-lilly-a83x: Don't use IRQ level flag for a GPIO
The card detect GPIO is using IRQ_TYPE_LEVEL_LOW in the GPIO flag cells
but this defined constant is meant to be used for a IRQ and not a GPIO.
So instead use GPIO_ACTIVE_LOW that seems to be the original intention.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 12 Oct 2015 23:19:54 +0000 (16:19 -0700)]
Documentation: ARM: List new omap MMC requirements
Earlier the PBIAS regulator was optional, not so with recent
omap_hsmmc changes. To make things easier for people with
custom .config files, let's add minimal documentation for it
as suggested by Russell King <rmk+kernel@arm.linux.org.uk>.
memory: omap-gpmc: dump "before" state before first modification
When gpmc_cs_show_timings is called in gpmc_cs_set_timings()
gpmc_cs_program_settings() was already run which modifies the CONFIG1
register. So to be more useful do the "before" dump earlier.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 12 Oct 2015 23:19:54 +0000 (16:19 -0700)]
memory: omap-gpmc: Fix unselectable debug option for GPMC
Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug")
added a debug option for GPMC, but somehow managed to keep it unselectable.
This probably happened because I had some uncommitted changes and the
GPMC option is selected in the platform specific Kconfig.
Let's also update the description a bit, it does not mention that
enabling the debug option also disables the reset of GPMC controller
during the init as pointed out by Uwe Kleine-König
<u.kleine-koenig@pengutronix.de> and Roger Quadros <rogerq@ti.com>.
Fixes: 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug") Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tomi Valkeinen [Fri, 25 Sep 2015 13:02:03 +0000 (16:02 +0300)]
ARM: dts: am57xx-beagle-x15: set VDD_SD to always-on
LDO1 regulator (VDD_SD) is connected to SoC's vddshv8. vddshv8 needs to
be kept always powered (see commit 5a0f93c6576a ("ARM: dts: Add
am57xx-beagle-x15"), but at the moment VDD_SD is enabled/disabled
depending on whether an SD card is inserted or not.
This patch sets LDO1 regulator to always-on.
This patch has a side effect of fixing another issue, HDMI DDC not
working when SD card is not inserted:
Why this happens is that the tpd12s015 (HDMI level shifter/ESD
protection chip) has LS_OE GPIO input, which needs to be enabled for the
HDMI DDC to work. LS_OE comes from gpio6_28. The pin that provides
gpio6_28 is powered by vddshv8, and vddshv8 comes from VDD_SD.
So when SD card is not inserted, VDD_SD is disabled, and LS_OE stays
off.
The proper fix for the HDMI DDC issue would be to maybe have the pinctrl
framework manage the pin specific power.
Apparently this fixes also a third issue (copy paste from Kishon's
patch):
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fixes: 5a0f93c6576a ("ARM: dts: Add am57xx-beagle-x15") Cc: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reported-by: Louis McCarthy <compeoree@gmail.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 2 Oct 2015 23:23:25 +0000 (18:23 -0500)]
ARM: dts: DRA74x: Add IOMMU nodes for DSP2
The DRA74x family of SoCs have a second DSP, that also has
two MMUs just like the DSP1 subsystem. Add the IOMMU nodes
for this DSP2 subsystem in disabled state to the DRA74x
specific DTS file, the nodes would need to be enabled
appropriately in the respective board DTS files.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 2 Oct 2015 23:23:24 +0000 (18:23 -0500)]
ARM: dts: DRA7: Add common IOMMU nodes
The DRA7xx family of SOCs have two IPUs and one DSP processor
subsystems in common. The IOMMU DT nodes have been added for
these processor subsystems, and have been disabled by default.
These MMUs are very similar to those on OMAP4 and OMAP5, with
the only difference being the presence of a second MMU within
the DSP subsystem for the EDMA port. The DSP IOMMUs also need
an additional 'ti,syscon-mmuconfig' property compared to the
IPU IOMMUs.
NOTE: The enabling of these nodes is left to the respective
board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 2 Oct 2015 23:23:23 +0000 (18:23 -0500)]
ARM: dts: DRA74x: Add dsp2_system syscon node
The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.
Add a syscon node for this module for the DSP2 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.
The node is added to the dra74x.dtsi file, as the DSP2 processor
subsystem is usually present only on the DRA74x variants of the
DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 2 Oct 2015 23:23:22 +0000 (18:23 -0500)]
ARM: dts: DRA7: Add dsp1_system syscon node
The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.
Add a syscon node for this module for the DSP1 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.
The node is added to the common dra7.dtsi file, as the DSP1
processor sub-system is mostly common across all the variants
of the DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Robert Nelson [Fri, 25 Sep 2015 15:10:31 +0000 (10:10 -0500)]
ARM: dts: Add am335x-bonegreen
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).
This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Jason Kridner <jkridner@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>