It's unlikely that TAINT_FIRMWARE_WORKAROUND causes false
lockdep messages, so do not disable lockdep in that case.
We still want to keep lockdep disabled in the
TAINT_OOT_MODULE case:
- bin-only modules can cause various instabilities in
their and in unrelated kernel code
- they are impossible to debug for kernel developers
- they also typically do not have the copyright license
permission to link to the GPL-ed lockdep code.
Suggested-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/n/tip-xopopjjens57r0i13qnyh2yo@git.kernel.org Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For null user mounts, do not invoke string length function
during session setup.
Reported-and-Tested-by: Chris Clayton <chris2553@googlemail.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ecryptfs_write() can enter an infinite loop when truncating a file to a
size larger than 4G. This only happens on architectures where size_t is
represented by 32 bits.
This was caused by a size_t overflow due to it incorrectly being used to
store the result of a calculation which uses potentially large values of
type loff_t.
[tyhicks@canonical.com: rewrite subject and commit message] Signed-off-by: Li Wang <liwang@nudt.edu.cn> Signed-off-by: Yunchuan Wen <wenyunchuan@kylinos.com.cn> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TV Out refresh rate was half of the specification for almost all modes.
Due to this reason pixel clock was so low for some modes causing flickering screen.
Otherwise hangcheck spuriously fires when running blitter/bsd-only
workloads.
Contrary to a similar patch by Ben Widawsky this does not check
INSTDONE of the other rings. Chris Wilson implied that in a failure to
detect a hang, most likely because INSTDONE was fluctuating. Thus only
check ACTHD, which as far as I know is rather reliable. Also, blitter
and bsd rings can't launch complex tasks from a single instruction
(like 3D_PRIM on the render with complex or even infinite shaders).
This fixes spurious gpu hang detection when running
tests/gem_hangcheck_forcewake on snb/ivb.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On DP monitor hot remove, clear DP_AUDIO_OUTPUT_ENABLE accordingly,
so that the audio driver will receive hot plug events and take action
to refresh its device state and ELD contents.
Note that the DP_AUDIO_OUTPUT_ENABLE bit may be enabled or disabled
only when the link training is complete and set to "Normal".
Tested OK for both hot plug/remove and DPMS on/off.
On HDMI monitor hot remove, clear SDVO_AUDIO_ENABLE accordingly, so that
the audio driver will receive hot plug events and take action to refresh
its device state and ELD contents.
The cleared SDVO_AUDIO_ENABLE bit needs to be restored to prevent losing
HDMI audio after DPMS on.
CC: Wang Zhenyu <zhenyu.z.wang@intel.com> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we hit EIO while writing LVID, the buffer uptodate bit is cleared.
This then results in an anoying warning from mark_buffer_dirty() when we
write the buffer again. So just set uptodate flag unconditionally.
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Cc: Dave Jones <davej@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 873bd4c (ASoC: Don't set invalid name string to snd_card->driver
field) broke generation of a driver name for all ASoC cards relying on the
automatic generation of one. Fix this by using the old default with spaces
replaced by underscores.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue happens under the following conditions:
1. preemption is off
2. __ARCH_WANT_INTERRUPTS_ON_CTXSW is defined
3. RT scheduling class
4. SMP system
Sequence is as follows:
1.suppose current task is A. start schedule()
2.task A is enqueued pushable task at the entry of schedule()
__schedule
prev = rq->curr;
...
put_prev_task
put_prev_task_rt
enqueue_pushable_task
4.pick the task B as next task.
next = pick_next_task(rq);
3.rq->curr set to task B and context_switch is started.
rq->curr = next;
4.At the entry of context_swtich, release this cpu's rq->lock.
context_switch
prepare_task_switch
prepare_lock_switch
raw_spin_unlock_irq(&rq->lock);
5.Shortly after rq->lock is released, interrupt is occurred and start IRQ context
6.try_to_wake_up() which called by ISR acquires rq->lock
try_to_wake_up
ttwu_remote
rq = __task_rq_lock(p)
ttwu_do_wakeup(rq, p, wake_flags);
task_woken_rt
7.push_rt_task picks the task A which is enqueued before.
task_woken_rt
push_rt_tasks(rq)
next_task = pick_next_pushable_task(rq)
8.At find_lock_lowest_rq(), If double_lock_balance() returns 0,
lowest_rq can be the remote rq.
(But,If preemption is on, double_lock_balance always return 1 and it
does't happen.)
push_rt_task
find_lock_lowest_rq
if (double_lock_balance(rq, lowest_rq))..
9.find_lock_lowest_rq return the available rq. task A is migrated to
the remote cpu/rq.
push_rt_task
...
deactivate_task(rq, next_task, 0);
set_task_cpu(next_task, lowest_rq->cpu);
activate_task(lowest_rq, next_task, 0);
10. But, task A is on irq context at this cpu.
So, task A is scheduled by two cpus at the same time until restore from IRQ.
Task A's stack is corrupted.
To fix it, don't migrate an RT task if it's still running.
Polling the outputs when the device is suspended can result in erroneous
status updates. Disable output polling during suspend to prevent this
from happening.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a race it was possible for a fence to be destroyed while another
thread was trying to synchronise with it. If this happened in the fallback
non-semaphore path, it lead to the following oops due to fence->channel
being NULL.
The value of this register is transferred to the V_COUNTER register at the
beginning of vertical blank. V_COUNTER is the reference for VLINE waits and
goes from VIEWPORT_Y_START to VIEWPORT_Y_START+VIEWPORT_HEIGHT during scanout,
so if VIEWPORT_Y_START is not 0, V_COUNTER actually went backwards at the
beginning of vertical blank, and VLINE waits excluding the whole scanout area
could never finish (possibly only if VIEWPORT_Y_START is larger than the length
of vertical blank in scanlines). Setting DESKTOP_HEIGHT to the framebuffer
height should prevent this for any kind of VLINE wait.
When isolating for migration, migration starts at the start of a zone
which is not necessarily pageblock aligned. Further, it stops isolating
when COMPACT_CLUSTER_MAX pages are isolated so migrate_pfn is generally
not aligned. This allows isolate_migratepages() to call pfn_to_page() on
an invalid PFN which can result in a crash. This was originally reported
against a 3.0-based kernel with the following trace in a crash dump.
The migrate_pfn is just below a memory hole and the free scanner is beyond
the hole. When isolate_migratepages started, it scans from migrate_pfn to
migrate_pfn+pageblock_nr_pages which is now in a memory hole. It checks
pfn_valid() on the first PFN but then scans into the hole where there are
not necessarily valid struct pages.
This patch ensures that isolate_migratepages calls pfn_valid when
necessary.
Reported-by: Herbert van den Bergh <herbert.van.den.bergh@oracle.com> Tested-by: Herbert van den Bergh <herbert.van.den.bergh@oracle.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a race condition that shows in conjunction with xip_file_fault() when
two threads of the same user process fault on the same memory page.
In this case, the race winner will install the page table entry and the
unlucky loser will cause an oops: xip_file_fault calls vm_insert_pfn (via
vm_insert_mixed) which drops out at this check:
retval = -EBUSY;
if (!pte_none(*pte))
goto out_unlock;
The resulting -EBUSY return value will trigger a BUG_ON() in
xip_file_fault.
This fix simply considers the fault as fixed in this case, because the
race winner has successfully installed the pte.
[akpm@linux-foundation.org: use conventional (and consistent) comment layout] Reported-by: David Sadler <dsadler@us.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Reported-by: Louis Alex Eisner <leisner@cs.ucsd.edu> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 463894705e4089d0ff69e7d877312d496ac70e5b deleted redundant
chan_id and chancnt initialization in dma drivers as this is done
in dma_async_device_register().
However, atc_enable_irq() relied on chan_id set before registering
the device, what left only channel 0 functional for this driver.
This patch introduces atc_enable/disable_chan_irq() as a variant
of atc_enable/disable_irq() with the channel as explicit argument.
In function pre_handler_kretprobe(), the allocated kretprobe_instance
object will get leaked if the entry_handler callback returns non-zero.
This may cause all the preallocated kretprobe_instance objects exhausted.
This issue can be reproduced by changing
samples/kprobes/kretprobe_example.c to probe "mutex_unlock". And the fix
is straightforward: just put the allocated kretprobe_instance object back
onto the free_instances list.
[akpm@linux-foundation.org: use raw_spin_lock/unlock] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Acked-by: Jim Keniston <jkenisto@us.ibm.com> Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, vendor-specific MADs (e.g with the FDR-10
attribute) are silently dropped by the driver, resulting in timeouts
at the sending side and inability to query/configure the relevant
feature. However, the ConnectX firmware is able to handle such MADs.
For unsupported attributes, the firmware returns a GET_RESPONSE MAD
containing an error status.
For example, for a FDR-10 node with LID 11:
# ibstat mlx4_0 1
CA: 'mlx4_0'
Port 1:
State: Active
Physical state: LinkUp
Rate: 40 (FDR10)
Base lid: 11
LMC: 0
SM lid: 24
Capability mask: 0x02514868
Port GUID: 0x0002c903002e65d1
Link layer: InfiniBand
Extended Port Query (EPI) vendor mad timeouts before the patch:
# smpquery MEPI 11 -d
ibwarn: [4196] smp_query_via: attr 0xff90 mod 0x0 route Lid 11
ibwarn: [4196] _do_madrpc: retry 1 (timeout 1000 ms)
ibwarn: [4196] _do_madrpc: retry 2 (timeout 1000 ms)
ibwarn: [4196] _do_madrpc: timeout after 3 retries, 3000 ms
ibwarn: [4196] mad_rpc: _do_madrpc failed; dport (Lid 11)
smpquery: iberror: [pid 4196] main: failed: operation EPI: ext port info query failed
EPI query works OK with the patch:
# smpquery MEPI 11 -d
ibwarn: [6548] smp_query_via: attr 0xff90 mod 0x0 route Lid 11
ibwarn: [6548] mad_rpc: data offs 64 sz 64
mad data
0000 0000 0000 0001 0000 0001 0000 0001
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
# Ext Port info: Lid 11 port 0
StateChangeEnable:...............0x00
LinkSpeedSupported:..............0x01
LinkSpeedEnabled:................0x01
LinkSpeedActive:.................0x01
Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Acked-by: Ira Weiny <weiny2@llnl.gov> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
is unable to access attached FireWire devices when MSI is enabled but
works if MSI is disabled.
http://www.mail-archive.com/alsa-user@lists.sourceforge.net/msg28251.html
Hence add the "disable MSI" quirks flag for this device, or in fact for
safety and simplicity for all current (R5U230, R5U231, R5U240) and
future Ricoh PCIe 1394 controllers.
Reported-by: Stefan Thomas <kontrapunktstefan@googlemail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once /proc/pid/mem is opened, the memory can't be released until
mem_release() even if its owner exits.
Change mem_open() to do atomic_inc(mm_count) + mmput(), this only
pins mm_struct. Change mem_rw() to do atomic_inc_not_zero(mm_count)
before access_remote_vm(), this verifies that this mm is still alive.
I am not sure what should mem_rw() return if atomic_inc_not_zero()
fails. With this patch it returns zero to match the "mm == NULL" case,
may be it should return -EINVAL like it did before e268337d.
Perhaps it makes sense to add the additional fatal_signal_pending()
check into the main loop, to ensure we do not hold this memory if
the target task was oom-killed.
If we are context switched whilst copying into a thread's
vfp_hard_struct then the partial copy may be corrupted by the VFP
context switching code (see "ARM: vfp: flush thread hwstate before
restoring context from sigframe").
This patch updates the ptrace VFP set code so that the thread state is
flushed before the copy, therefore disabling VFP and preventing
corruption from occurring.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a preemptible kernel, vfp_set() can be preempted, causing the
hardware VFP context to be switched while the thread vfp state is
being read and modified. This leads to a race condition which can
cause the thread vfp state to become corrupted if lazy VFP context
save occurs due to preemption in between the time thread->vfpstate
is read and the time the modified state is written back.
This may occur if preemption occurs during the execution of a
ptrace() call which modifies the VFP register state of a thread.
Such instances should be very rare in most realistic scenarios --
none has been reported, so far as I am aware. Only uniprocessor
systems should be affected, since VFP context save is not currently
lazy in SMP kernels.
The problem was introduced by my earlier patch migrating to use
regsets to implement ptrace.
This patch does a vfp_sync_hwstate() before reading
thread->vfpstate, to make sure that the thread's VFP state is not
live in the hardware registers while the registers are modified.
Thanks to Will Deacon for spotting this.
Signed-off-by: Dave Martin <dave.martin@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following execution of a signal handler, we currently restore the VFP
context from the ucontext in the signal frame. This involves copying
from the user stack into the current thread's vfp_hard_struct and then
flushing the new data out to the hardware registers.
This is problematic when using a preemptible kernel because we could be
context switched whilst updating the vfp_hard_struct. If the current
thread has made use of VFP since the last context switch, the VFP
notifier will copy from the hardware registers into the vfp_hard_struct,
overwriting any data that had been partially copied by the signal code.
Disabling preemption across copy_from_user calls is a terrible idea, so
instead we move the VFP thread flush *before* we update the
vfp_hard_struct. Since the flushing is performed lazily, this has the
effect of disabling VFP and clearing the CPU's VFP state pointer,
therefore preventing the thread from being updated with stale data on
the next context switch.
Tested-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: UK KIM <w0806.kim@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Herbert Poetzl reported a performance regression since 2.6.39. The test
is a simple dd read, but with big block size. The reason is:
T1: ra (A, A+128k), (A+128k, A+256k)
T2: lock_page for page A, submit the 256k
T3: hit page A+128K, ra (A+256k, A+384). the range isn't submitted
because of plug and there isn't any lock_page till we hit page A+256k
because all pages from A to A+256k is in memory
T4: hit page A+256k, ra (A+384, A+ 512). Because of plug, the range isn't
submitted again.
T5: lock_page A+256k, so (A+256k, A+512k) will be submitted. The task is
waitting for (A+256k, A+512k) finish.
There is no request to disk in T3 and T4, so readahead pipeline breaks.
We really don't need block plug for generic_file_aio_read() for buffered
I/O. The readahead already has plug and has fine grained control when I/O
should be submitted. Deleting plug for buffered I/O fixes the regression.
One side effect is plug makes the request size 256k, the size is 128k
without it. This is because default ra size is 128k and not a reason we
need plug here.
Vivek said:
: We submit some readahead IO to device request queue but because of nested
: plug, queue never gets unplugged. When read logic reaches a page which is
: not in page cache, it waits for page to be read from the disk
: (lock_page_killable()) and that time we flush the plug list.
:
: So effectively read ahead logic is kind of broken in parts because of
: nested plugging. Removing top level plug (generic_file_aio_read()) for
: buffered reads, will allow unplugging queue earlier for readahead.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Reported-by: Herbert Poetzl <herbert@13thfloor.at> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we forcibly clear ASPM state on all devices if the BIOS indicates
that the feature isn't supported. Based on the Microsoft presentation
"PCI Express In Depth for Windows Vista and Beyond", I'm starting to think
that this may be an error. The implication is that unless the platform
grants full control via _OSC, Windows will not touch any PCIe features -
including ASPM. In that case clearing ASPM state would be an error unless
the platform has granted us that control.
This patch reworks the ASPM disabling code such that the actual clearing
of state is triggered by a successful handoff of PCIe control to the OS.
The general ASPM code undergoes some changes in order to ensure that the
ability to clear the bits isn't overridden by ASPM having already been
disabled. Further, this theoretically now allows for situations where
only a subset of PCIe roots hand over control, leaving the others in the
BIOS state.
It's difficult to know for sure that this is the right thing to do -
there's zero public documentation on the interaction between all of these
components. But enough vendors enable ASPM on platforms and then set this
bit that it seems likely that they're expecting the OS to leave them alone.
Measured to save around 5W on an idle Thinkpad X220.
This fix changes the way baudrates are set on the CP210x devices from
Silicon Labs. The CP2101/2/3 will respond to both a GET/SET_BAUDDIV
command, and GET/SET_BAUDRATE command, while CP2104 and higher devices
only respond to GET/SET_BAUDRATE. The current cp210x.ko driver in
kernel version 3.2.0 only implements the GET/SET_BAUDDIV command.
This patch implements the two new codes for the GET/SET_BAUDRATE
commands. Then there is a change in the way that the baudrate is
assigned or retrieved. This is done according to the CP210x USB
specification in AN571. This document can be found here:
http://www.silabs.com/pages/DownloadDoc.aspx?FILEURL=Support%20Documents/TechnicalDocs/AN571.pdf&src=DocumentationWebPart
Sections 5.3/5.4 describe the USB packets for the old baudrate method.
Sections 5.5/5.6 describe the USB packets for the new method. This
patch also implements the new request scheme, and eliminates the
unnecessary baudrate calculations since it uses the "actual baudrate"
method.
This patch solves the problem reported for the CP2104 in bug 42586,
and also keeps support for all other devices (CP2101/2/3).
This patchfile is also attached to the bug report on
bugzilla.kernel.org. This patch has been developed and test on the
3.2.0 mainline kernel version under Ubuntu 10.11.
Signed-off-by: Preston Fick <preston.fick@silabs.com>
[duplicate patch also sent by Johan - gregkh] Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
md5 key is added in socket through remote address.
remote address should be used in finding md5 key when
sending out reset packet.
Signed-off-by: shawnlu <shawn.lu@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes tcp_trim_head() to recalculate the number of
segments in the skb with the skb's existing MSS, so trimming the head
causes the skb segment count to be monotonically non-increasing - it
should stay the same or go down, but not increase.
Previously tcp_trim_head() used the current MSS of the connection. But
if there was a decrease in MSS between original transmission and ACK
(e.g. due to PMTUD), this could cause tcp_trim_head() to
counter-intuitively increase the segment count when trimming bytes off
the head of an skb. This violated assumptions in tcp_tso_acked() that
tcp_trim_head() only decreases the packet count, so that packets_acked
in tcp_tso_acked() could underflow, leading tcp_clean_rtx_queue() to
pass u32 pkts_acked values as large as 0xffffffff to
ca_ops->pkts_acked().
As an aside, if tcp_trim_head() had really wanted the skb to reflect
the current MSS, it should have called tcp_set_skb_tso_segs()
unconditionally, since a decrease in MSS would mean that a
single-packet skb should now be sliced into multiple segments.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Nandita Dukkipati <nanditad@google.com> Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rds_sock_info() triggers locking warnings because we try to perform a
local_bh_enable() (via sock_i_ino()) while hardware interrupts are
disabled (via taking rds_sock_lock).
There is no reason for rds_sock_lock to be a hardware IRQ disabling
lock, none of these access paths run in hardware interrupt context.
Therefore making it a BH disabling lock is safe and sufficient to
fix this bug.
Reported-by: Kumar Sanghvi <kumaras@chelsio.com> Reported-by: Josh Boyer <jwboyer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) Target of the conditional jump in case a divide by 0 is performed
by a bpf is wrong.
2) Must 'generate' the full function prologue/epilogue at pass=0,
or else we can stop too early in pass=1 if the proglen doesnt change.
(if the increase of prologue/epilogue equals decrease of all
instructions length because some jumps are converted to near jumps)
3) Change the wrong length detection at the end of code generation to
issue a more explicit message, no need for a full stack trace.
Reported-by: Phil Oester <kernel@linuxace.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a packet is received on an L2TP IP socket (L2TPv3 IP link
encapsulation), the l2tpip socket's backlog_rcv function calls
xfrm4_policy_check(). This is not necessary, since it was called
before the skb was added to the backlog. With CONFIG_NET_NS enabled,
xfrm4_policy_check() will oops if skb->dev is null, so this trivial
patch removes the call.
This bug has always been present, but only when CONFIG_NET_NS is
enabled does it cause problems. Most users are probably using UDP
encapsulation for L2TP, hence the problem has only recently
surfaced.
Signed-off-by: James Chapman <jchapman@katalix.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bond_alb_init_slave() is called from bond_enslave() and sets the slave's MAC
address. This is done differently for TLB and ALB modes.
bond->alb_info.rlb_enabled is used to discriminate between the two modes but
this flag may be uninitialized if the slave is being enslaved prior to calling
bond_open() -> bond_alb_initialize() on the master.
It turns out all the callers of alb_set_slave_mac_addr() pass
bond->alb_info.rlb_enabled as the hw parameter.
This patch cleans up the unnecessary parameter of alb_set_slave_mac_addr() and
makes the function decide based on the bonding mode instead, which fixes the
above problem.
Reported-by: Narendra K <Narendra_K@Dell.com> Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
caif is a subsystem and as such it needs to register with
register_pernet_subsys instead of register_pernet_device.
Among other problems using register_pernet_device was resulting in
net_generic being called before the caif_net structure was allocated.
Which has been causing net_generic to fail with either BUG_ON's or by
return NULL pointers.
A more ugly problem that could be caused is packets in flight why the
subsystem is shutting down.
To remove confusion also remove the cruft cause by inappropriately
trying to fix this bug.
With the aid of the previous patch I have tested this patch and
confirmed that using register_pernet_subsys makes the failure go away as
it should.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Tested-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By definition net_generic should never be called when it can return
NULL. Fail conspicously with a BUG_ON to make it clear when people mess
up that a NULL return should never happen.
Recently there was a bug in the CAIF subsystem where it was registered
with register_pernet_device instead of register_pernet_subsys. It was
erroneously concluded that net_generic could validly return NULL and
that net_assign_generic was buggy (when it was just inefficient).
Hopefully this BUG_ON will prevent people to coming to similar erroneous
conclusions in the futrue.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Tested-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new net namespace is created, we should attach to it a "struct
net_generic" with enough slots (even empty), or we can hit the following
BUG_ON() :
net_alloc_generic() should take into account the maximum index into the
ptr array, as a subsystem might use net_generic() anytime.
This also reduces number of reallocations in net_assign_generic()
Reported-by: Sasha Levin <levinsasha928@gmail.com> Tested-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Sjur Brændeland <sjur.brandeland@stericsson.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe does not strictly require the USB_CDC_DMM_TYPE
descriptor, which is a good thing as it makes the driver
usable on non-conforming interfaces. A user could e.g.
bind to it to a CDC ECM interface by using the new_id and
bind sysfs files. But this would fail with a 0 buffer length
due to the missing descriptor.
Fix by defining a reasonable fallback size: The minimum
device receive buffer size required by the CDC WMC standard,
revision 1.1
As it turns out, there was a mismatch between the allocated inbuf size
(desc->bMaxPacketSize0, typically something like 64) and the length we
specified in the URB (desc->wMaxCommand, typically something like 2048)
wdm_disconnect() waits for the mutex held by wdm_read() before
calling wake_up_all(). This causes a deadlock, preventing device removal
to complete. Do the wake_up_all() before we start waiting for the locks.
Properly clamp temperature limits set by the user. Without this fix,
attempts to write temperature limits above the maximum supported by
the chip (255 degrees Celsius) would arbitrarily and unexpectedly
result in the limit being set to 0 degree Celsius.
When a TD length mismatch is found during isoc TRB enqueue, it directly
returns -EINVAL. However, isoc transfer is partially enqueued at this time,
and the ring should be cleared.
This should be backported to kernels as old as 2.6.36, which contain the
commit 522989a27c7badb608155b1f1dea3487ed431f74 "xhci: Fix failed
enqueue in the middle of isoch TD."
The xHCI hub port code gets passed a zero-based port number by the USB
core. It then adds one to in order to find a device slot by port number
and device speed by calling xhci_find_slot_id_by_port. That function
clearly states it requires a one-based port number. The xHCI port
status change event handler was using a zero-based port number that it
got from find_faked_portnum_from_hw_portnum, not a one-based port
number. This lead to the doorbells never being rung for a device after
a resume, or worse, a different device with the same speed having its
doorbell rung (which could lead to bad power management in the xHCI host
controller).
This patch should be backported to kernels as old as 2.6.39.
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes the max length for the usb seven segment delcom device to 8
from 6. Delcom has both 6 and 8 variants and having 8 works fine with
devices which are only 6.
Signed-off-by: Harrison Metzger <harrisonmetz@gmail.com> Signed-off-by: Stuart Pook <stuart@acm.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The assignment of handle in vmw_framebuffer_create_handle doesn't actually do anything useful and is incorrectly assigning an integer value to a pointer argument. It appears that this is a typo and should be dereferencing handle rather than assigning to it directly. This fixes a bug where an undefined handle value is potentially returned to user-space.
Signed-off-by: Ryan Mallon <rmallon@gmail.com> Reviewed-by: Jakob Bornecrantz<jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was an error on the jsm driver that would cause it to be unable to
recover after a second error is detected.
At the first error, the device recovers properly:
[72521.485691] EEH: Detected PCI bus error on device 0003:02:00.0
[72521.485695] EEH: This PCI device has failed 1 times in the last hour:
...
[72532.035693] ttyn3 at MMIO 0x0 (irq = 49) is a jsm
[72532.105689] jsm: Port 3 added
However, at the second error, it cascades until EEH disables the device:
[72631.229549] Call Trace:
...
[72641.725687] jsm: Port 3 added
[72641.725695] EEH: Detected PCI bus error on device 0003:02:00.0
[72641.725698] EEH: This PCI device has failed 3 times in the last hour:
It was caused because the PCI state was not being saved after the first
restore. Therefore, at the second recovery the PCI state would not be
restored.
Signed-off-by: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com> Signed-off-by: Breno Leitao <brenohl@br.ibm.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Protect against pl011_console_write() and the interrupt for
the console UART running concurrently on different CPUs.
Otherwise the console_write could spin for a long time
waiting for the UART to become not busy, while the other
CPU continuously services UART interrupts and keeps the
UART busy.
The checks for sysrq and oops_in_progress are taken
from 8250.c.
Commit 74c2107759d (serial: Use block_til_ready helper) and its fixup 3f582b8c110 (serial: fix termios settings in open) introduced a
regression on UV systems. The serial eventually freezes while being
used. It's completely unpredictable and sometimes needs a heap of
traffic to happen first.
To reproduce this, yast installation was used as it turned out to be
pretty reliable in reproducing. Especially during installation process
where one doesn't have an SSH daemon running. And no monitor as the HW
is completely headless. So this was fun to find. Given the machine
doesn't boot on vanilla before 2.6.36 final. (And the commits above
are older.)
Unless there is some bad race in the code, the hardware seems to be
pretty broken. Otherwise pure MSR read should not cause such a bug,
or?
So to prevent the bug, revert to the old behavior. I.e. read modem
status only if we really have to -- for non-CLOCAL set serials.
Non-CLOCAL works on this hardware OK, I tried. See? I don't.
Calling edge_remove_sysfs_attrs from edge_disconnect is too late
as the device has already been removed from sysfs.
Do the simple and obvious thing and make edge_remove_sysfs_attrs
the port_remove method.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Reported-by: Wolfgang Frisch <wfpub@roembden.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit b1ffb4c851f1 ("USB: Fix Corruption
issue in USB ftdi driver ftdi_sio.c") which caused the termios settings
to no longer be initialised at open. Consequently it was no longer
possible to set the port to the default speed of 9600 baud without first
changing to another baud rate and back again.
Reported-by: Roland Ramthun <mail@roland-ramthun.de> Signed-off-by: Johan Hovold <jhovold@gmail.com> Tested-by: Roland Ramthun <mail@roland-ramthun.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return EINVAL if new baud_base does not match the current one.
The baud_base is device specific and can not be changed. This restores
the old (pre-2005) behaviour which was changed due to a
misunderstanding regarding this fact (see
https://lkml.org/lkml/2005/1/20/84).
On v7, we use the same cache maintenance instructions for data lines
as for unified lines. This was not the case for v6, where HARVARD_CACHE
was defined to indicate the L1 cache topology.
This patch removes the erroneous compile-time check for HARVARD_CACHE in
proc-v7.S, ensuring that we perform I-side invalidation at boot.
Reported-and-Acked-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Catalin Marinas <Catalin.Marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syslog-ng versions before 3.3.0beta1 (2011-05-12) assume that
CAP_SYS_ADMIN is sufficient to access syslog, so ever since CAP_SYSLOG
was introduced (2010-11-25) they have triggered a warning.
Commit ee24aebffb75 ("cap_syslog: accept CAP_SYS_ADMIN for now")
improved matters a little by making syslog-ng work again, just keeping
the WARN_ONCE(). But still, this is a warning that writes a stack trace
we don't care about to syslog, sets a taint flag, and alarms sysadmins
when nothing worse has happened than use of an old userspace with a
recent kernel.
Convert the WARN_ONCE to a printk_once to avoid that while continuing to
give userspace developers a hint that this is an unwanted
backward-compatibility feature and won't be around forever.
Reported-by: Ralf Hildebrandt <ralf.hildebrandt@charite.de> Reported-by: Niels <zorglub_olsen@hotmail.com> Reported-by: Paweł Sikora <pluto@agmk.net> Signed-off-by: Jonathan Nieder <jrnieder@gmail.com> Liked-by: Gergely Nagy <algernon@madhouse-project.org> Acked-by: Serge Hallyn <serge@hallyn.com> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already set the mode polarity using the SDVO commands with struct
intel_sdvo_dtd. We have at least 3 bugs that get fixed with this patch.
The documentation, despite not clear, can also be interpreted in a way
that suggests this patch is needed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=15766
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42174
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43333 Reviewed-by: Eric Anholt <eric@anholt.net> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The very same problem is seen on Haier W18 laptop with ALC861 as seen
on ASUS A6Rp, which was fixed by the commit 3b25eb69.
Now we just need to add a new SSID entry pointing to the same fixup.
The refactoring of Realtek codec driver in 3.2 kernel caused a
regression for ASUS A6Rp laptop; it doesn't give any output.
The reason was that this machine has a secret master mute (or EAPD)
control via NID 0x0f VREF. Setting VREF50 on this node makes the
sound working again.
We've decided to provide CPU family specific container files
(starting with CPU family 15h). E.g. for family 15h we have to
load microcode_amd_fam15h.bin instead of microcode_amd.bin
Rationale is that starting with family 15h patch size is larger
than 2KB which was hard coded as maximum patch size in various
microcode loaders (not just Linux).
Container files which include patches larger than 2KB cause
different kinds of trouble with such old patch loaders. Thus we
have to ensure that the default container file provides only
patches with size less than 2KB.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Borislav Petkov <borislav.petkov@amd.com> Cc: <stable@kernel.org> Link: http://lkml.kernel.org/r/20120120164412.GD24508@alberich.amd.com
[ documented the naming convention and tidied the code a bit. ] Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When finding the longest extent in an AG, we read the value directly
out of the AGF buffer without endian conversion. This will give an
incorrect length, resulting in FITRIM operations potentially not
trimming everything that it should.
Note, for 3.0-stable this has been modified to apply to
fs/xfs/linux-2.6/xfs_discard.c instead of fs/xfs/xfs_discard.c. -bpm
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ahash driver returns -EBUSY, AH4/6 input functions return
NET_XMIT_DROP, presumably copied from the output code path. But
returning transmit codes on input doesn't make a lot of sense.
Since NET_XMIT_DROP is a positive int, this gets interpreted as
the next header type (i.e., success). As that can only end badly,
remove the check.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiple users of the function tracer can register their functions
with the ftrace_ops structure. The accounting within ftrace will
update the counter on each function record that is being traced.
When the ftrace_ops filtering adds or removes functions, the
function records will be updated accordingly if the ftrace_ops is
still registered.
When a ftrace_ops is removed, the counter of the function records,
that the ftrace_ops traces, are decremented. When they reach zero
the functions that they represent are modified to stop calling the
mcount code.
When changes are made, the code is updated via stop_machine() with
a command passed to the function to tell it what to do. There is an
ENABLE and DISABLE command that tells the called function to enable
or disable the functions. But the ENABLE is really a misnomer as it
should just update the records, as records that have been enabled
and now have a count of zero should be disabled.
The DISABLE command is used to disable all functions regardless of
their counter values. This is the big off switch and is not the
complement of the ENABLE command.
To make matters worse, when a ftrace_ops is unregistered and there
is another ftrace_ops registered, neither the DISABLE nor the
ENABLE command are set when calling into the stop_machine() function
and the records will not be updated to match their counter. A command
is passed to that function that will update the mcount code to call
the registered callback directly if it is the only one left. This
means that the ftrace_ops that is still registered will have its callback
called by all functions that have been set for it as well as the ftrace_ops
that was just unregistered.
Here's a way to trigger this bug. Compile the kernel with
CONFIG_FUNCTION_PROFILER set and with CONFIG_FUNCTION_GRAPH not set:
CONFIG_FUNCTION_PROFILER=y
# CONFIG_FUNCTION_GRAPH is not set
This will force the function profiler to use the function tracer instead
of the function graph tracer.
The same problem could have happened with the trace_probe_ops,
but they are modified with the set_frace_filter file which does the
update at closure of the file.
The simple solution is to change ENABLE to UPDATE and call it every
time an ftrace_ops is unregistered.
Currently, if set_ftrace_filter() is called when the ftrace_ops is
active, the function filters will not be updated. They will only be updated
when tracing is disabled and re-enabled.
Update the functions immediately during set_ftrace_filter().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever the hash of the ftrace_ops is updated, the record counts
must be balance. This requires disabling the records that are set
in the original hash, and then enabling the records that are set
in the updated hash.
Moving the update into ftrace_hash_move() removes the bug where the
hash was updated but the records were not, which results in ftrace
triggering a warning and disabling itself because the ftrace_ops filter
is updated while the ftrace_ops was registered, and then the failure
happens when the ftrace_ops is unregistered.
The current code will not trigger this bug, but new code will.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For rounds 16--79, W[i] only depends on W[i - 2], W[i - 7], W[i - 15] and W[i - 16].
Consequently, keeping all W[80] array on stack is unnecessary,
only 16 values are really needed.
Using W[16] instead of W[80] greatly reduces stack usage
(~750 bytes to ~340 bytes on x86_64).
Line by line explanation:
* BLEND_OP
array is "circular" now, all indexes have to be modulo 16.
Round number is positive, so remainder operation should be
without surprises.
* initial full message scheduling is trimmed to first 16 values which
come from data block, the rest is calculated before it's needed.
* original loop body is unrolled version of new SHA512_0_15 and
SHA512_16_79 macros, unrolling was done to not do explicit variable
renaming. Otherwise it's the very same code after preprocessing.
See sha1_transform() code which does the same trick.
Patch survives in-tree crypto test and original bugreport test
(ping flood with hmac(sha512).
See FIPS 180-2 for SHA-512 definition
http://csrc.nist.gov/publications/fips/fips180-2/fips180-2withchangenotice.pdf
If sha512_update will ever be entered twice, hash will be silently
calculated incorrectly.
Probably the easiest way to notice incorrect hashes being calculated is
to run 2 ping floods over AH with hmac(sha512):
#!/usr/sbin/setkey -f
flush;
spdflush;
add IP1 IP2 ah 25 -A hmac-sha512 0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000025;
add IP2 IP1 ah 52 -A hmac-sha512 0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000052;
spdadd IP1 IP2 any -P out ipsec ah/transport//require;
spdadd IP2 IP1 any -P in ipsec ah/transport//require;
XfrmInStateProtoError will start ticking with -EBADMSG being returned
from ah_input(). This never happens with, say, hmac(sha1).
With patch applied (on BOTH sides), XfrmInStateProtoError does not tick
with multiple bidirectional ping flood streams like it doesn't tick
with SHA-1.
After this patch sha512_transform() will start using ~750 bytes of stack on x86_64.
This is OK for simple loads, for something more heavy, stack reduction will be done
separatedly.
Commit b52a360b forgot to call xfs_iunlock() when it detected corrupted
symplink and bailed out. Fix it by jumping to 'out' instead of doing return.
CC: Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Alex Elder <elder@kernel.org> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the master tries to authenticate a client using drm_authmagic and
that client has already closed its drm file descriptor,
either wilfully or because it was terminated, the
call to drm_authmagic will dereference a stale pointer into kmalloc'ed memory
and corrupt it.
Typically this results in a hard system hang.
This patch fixes that problem by removing any authentication tokens
(struct drm_magic_entry) open for a file descriptor when that file
descriptor is closed.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If pages passed to the eCryptfs extent-based crypto functions are not
mapped and the module parameter ecryptfs_verbosity=1 was specified at
loading time, a NULL pointer dereference will occur.
Note that this wouldn't happen on a production system, as you wouldn't
pass ecryptfs_verbosity=1 on a production system. It leaks private
information to the system logs and is for debugging only.
The debugging info printed in these messages is no longer very useful
and rather than doing a kmap() in these debugging paths, it will be
better to simply remove the debugging paths completely.
Most filesystems call inode_change_ok() very early in ->setattr(), but
eCryptfs didn't call it at all. It allowed the lower filesystem to make
the call in its ->setattr() function. Then, eCryptfs would copy the
appropriate inode attributes from the lower inode to the eCryptfs inode.
This patch changes that and actually calls inode_change_ok() on the
eCryptfs inode, fairly early in ecryptfs_setattr(). Ideally, the call
would happen earlier in ecryptfs_setattr(), but there are some possible
inode initialization steps that must happen first.
Since the call was already being made on the lower inode, the change in
functionality should be minimal, except for the case of a file extending
truncate call. In that case, inode_newsize_ok() was never being
called on the eCryptfs inode. Rather than inode_newsize_ok() catching
maximum file size errors early on, eCryptfs would encrypt zeroed pages
and write them to the lower filesystem until the lower filesystem's
write path caught the error in generic_write_checks(). This patch
introduces a new function, called ecryptfs_inode_newsize_ok(), which
checks if the new lower file size is within the appropriate limits when
the truncate operation will be growing the lower file.
In summary this change prevents eCryptfs truncate operations (and the
resulting page encryptions), which would exceed the lower filesystem
limits or FSIZE rlimits, from ever starting.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Reviewed-by: Li Wang <liwang@nudt.edu.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ecryptfs_write() handles the truncation of eCryptfs inodes. It grabs a
page, zeroes out the appropriate portions, and then encrypts the page
before writing it to the lower filesystem. It was unkillable and due to
the lack of sparse file support could result in tying up a large portion
of system resources, while encrypting pages of zeros, with no way for
the truncate operation to be stopped from userspace.
This patch adds the ability for ecryptfs_write() to detect a pending
fatal signal and return as gracefully as possible. The intent is to
leave the lower file in a useable state, while still allowing a user to
break out of the encryption loop. If a pending fatal signal is detected,
the eCryptfs inode size is updated to reflect the modified inode size
and then -EINTR is returned.
Print inode on metadata read failure. The only real
way of dealing with metadata read failures is to delete
the underlying file system file. Having the inode
allows one to 'find . -inum INODE`.
[tyhicks@canonical.com: Removed some minor not-for-stable parts] Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log