omap: mmc: extended to pass host capabilities from board file
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Tue, 31 Aug 2010 10:12:56 +0000 (10:12 +0000)]
omap2: McBSP: Remove mux code for OMAP2420 McBSP2 and do cleanups
This 'legacy' OMAP2420 McBSP2 muxing code is currently broken after recent
conversion to new mux code. The omap_mcbsp_request calling this code is
usually called after booting whereas the omap_mux_init_signal is __init
marked so null pointer dereference would occur.
Fix this by removing the muxing code and let the bootloader or board file to
do it if necessary. Remove also omap2_mcbsp_ops as there is no use for it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Tue, 31 Aug 2010 08:11:44 +0000 (08:11 +0000)]
omap: McBSP: Do not enable SRG in slave mode
McBSP SRG (Sample Rate Generator) and FSG (Frame Sync
Generator) is only needed to be enabled, when McBSP
is master.
In McBSP slave mode, the SRG, and FSG can be kept disabled,
which might save some power at the end in this configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Kasatkin [Fri, 20 Aug 2010 13:44:46 +0000 (13:44 +0000)]
omap: crypto: updates to enable omap aes
Updates to enable omap aes
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
[tony@atomide.com: updated to use CONFIG_ARCH_OMAP2/3 instead of old 24XX/34XX] Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix this and similar build warnings when building with
omap_4430sdp_defconfig.
CC arch/arm/mach-omap2/board-4430sdp.o
In file included from arch/arm/mach-omap2/board-4430sdp.c:36:
arch/arm/plat-omap/include/plat/usb.h:109: warning: return type defaults to 'int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Hema HK [Fri, 24 Sep 2010 16:23:19 +0000 (10:23 -0600)]
OMAP: hwmod: Set autoidle after smartidle during _sysc_enable
OMAP USBOTG module has a requirement to set the autoidle bit only after
setting smartidle bit. Modified the _sys_enable api to set the smartidle
first and then the autoidle bit. Setting this will not have any impact on the
other modules.
Signed-off-by: Hema HK <hemahk@ti.com> Signed-off-by: Partha Basak <p-basak2@ti.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Acked-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap4_cm_wait_module_ready function would only check for
the modules to be completely functional before declaring them
ready to be accessed.
There might also be instances where in the module is actually
in idle (under h/w control) but should still be declared
accessible, as the h/w control would make it functional when
needed.
Hence make omap4_cm_wait_module_ready return true in case
the module is fully functional *or* in idle state.
Fail only if the module is fully disabled or stuck intransition.
The explaination from the TRM for the idlest bits on OMAP4 is as
below for quick reference
Module idle state:
0x0 func: Module is fully functional, including OCP
0x1 trans: Module is performing transition: wakeup, or sleep, or sleep
abortion
0x2 idle: Module is in Idle mode (only OCP part). It is functional if
using separate functional clock
0x3 disabled: Module is disabled and cannot be accessed
OMAP: omap_device: Fix to support multiple hwmods for a single device
Currently there is a bug in the existing omap_device core code when
extracting the hwmod structures passed to omap_device_build_ss(). This bug
gets exposed only when passing multiple hwmod structures to
omap_device_build_ss() resulting in incorrect extraction from second hwmod
structure.
This fix uses the pointer to pointer to omap_hwmod structure (array of
pointers to omap_hwmod structure) passed to omap_device_build_ss() to
correctly extract the appropriate omap_hwmod structure.
This patch has been created and tested on lo/master and mainline.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Acked-by: Benoit Cousson <b-cousson@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Cc: Charulatha V <charu@ti.com> Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Jarkko Nikula [Fri, 20 Aug 2010 06:36:28 +0000 (09:36 +0300)]
omap: n8x0: Mux i2s codec port pins for McBSP block
Bootloader on Nokia N800 and N810 muxes I2C codec port pins for EAC block.
As there is no driver and use for EAC, mux those pins for McBSP instead
since N810 ASoC drivers can use it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Fri, 20 Aug 2010 06:36:28 +0000 (09:36 +0300)]
omap: n8x0: Register i2c2 and add board info with tlv320aic3xfor N810
Second i2c bus on Nokia N800 and N810 shares both common and hw specific
peripherals. Register now this bus and add board info with tlv320aic3x for
N810. Common peripherals may be added as an additional board info to
omap_register_i2c_bus(2, ...);
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Fri, 20 Aug 2010 06:36:28 +0000 (09:36 +0300)]
omap: n8x0: Cleanup i2c1 and menelaus registration
- Move n8x0_i2c_board_info_1 out from #ifdef CONFIG_MENELAUS block,
register i2c1 in n8x0_init_machine and do a few clean-ups around these.
Code looks better if board infos are grouped together
- Mark n8x0_i2c_board_info_1 and n8x0_menelaus_platform_data with __initdata
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin Hilman [Wed, 22 Sep 2010 23:06:27 +0000 (16:06 -0700)]
OMAP: GPIO: ensure debounce clocks are disabled during idle/suspend
If a GPIO bank has more than one GPIO with debounce enabled, the
debounce clock will not be fully disabled before going to
idle/suspend.
In the idle path, we just do a single clk_disable() of the bank's
debounce clock. If there are multiple debounce-enabled GPIOs in the
bank, that clocks usage count will be > 1, so the clk_disable() will
not actually disable the clock.
So the fix is to clk_disable() for every debounce-enabled GPIO in the
bank (and an equivalent clk_enable() of course.)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Benoit Cousson [Thu, 5 Aug 2010 13:22:35 +0000 (15:22 +0200)]
OMAP4: pm: Change l3_main to l3_main_1 during bus device init
The OMAP4 L3 interconnect is split in 3 part for power saving reason.
Because of that there is no l3_main like on OMAP2 & 3 but 3 differentes
l3_main_X instances.
In the case of OMAP4, query only the l3_main_1 part. The clock and
voltage are shared across the 3 instances.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 23 Aug 2010 15:10:55 +0000 (08:10 -0700)]
OMAP: omap_device: make all devices a child of a new parent device
In order to help differentiate omap_devices from normal
platform_devices, make them all a parent of a new common parent
device.
Then, in order to determine if a platform_device is also an
omap_device, checking the parent is all that is needed.
Users of this feature are the runtime PM core for OMAP, where we need
to know if a device being passed in is an omap_device or not in order
to know whether to call the omap_device API with it.
In addition, all omap_devices will now show up under /sys/devices/omap
instead of /sys/devices/platform
Acked-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The dereference method of checking for a valid omap_device when
wrapping a platform_device is rather unsafe and dangerous.
Instead, a better way of checking for a valid omap-device is
to use a common parent device for all omap_devices, then a check
can simply be made using the device parent. The only user of this
API was the initial version of the runtime PM core for OMAP. This
has now been switched to check device parent, so there are no more
users of this API.
Acked-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley [Tue, 14 Sep 2010 21:56:53 +0000 (15:56 -0600)]
OMAP clockdomain: initialize clockdomain registers when the clockdomain layer starts
When the clockdomain layer initializes, place all clockdomains into
software-supervised mode, and clear all wakeup and sleep dependencies
immediately, rather than waiting for the PM code to do this later.
This fixes a major bug where critical sleep dependencies added by the
hwmod code are cleared during late PM init.
As a side benefit, the _init_{wk,sleep}dep_usecount() functions are no
longer needed, so remove them.
Kevin Hilman <khilman@deeprootsystems.com> did all the really hard work on
this, identifying the problem and finding the bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has an iva device and a dsp devcice where as OMAP2/3
has only an iva device. In this file the iva device in the
system is registered under the name dsp_dev and the API
to retrieve the iva device is omap2_get_dsp_device.
This patch renames the dsp_dev to iva_dev, renames
omap2_get_dsp_device to omap2_get_iva_device,
registers dsp_dev for OMAP4 and adds a new API
omap4_get_dsp_device to retrieve the dep_dev.
Signed-off-by: Thara Gopinath <thara@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Wed, 8 Sep 2010 23:37:42 +0000 (16:37 -0700)]
OMAP3: PM: move device-specific special cases from PM core into CPUidle
In an effort to simplify the core idle path, move any device-specific
special case handling from the core PM idle path into the CPUidle
pre-idle checking path.
This keeps the core, interrupts-disabled idle path streamlined and
independent of any device-specific handling, and also allows CPUidle
to do the checking only for certain C-states as needed. This patch
has the device checks in place for all states with the CHECK_BM flag,
namely all states >= C2.
This patch was inspired by a similar patch written by Tero Kristo as
part of a larger series to add INACTIVE state support.
NOTE: This is a baby-step towards decoupling device idle (or system
idle) from CPU idle. Eventually, CPUidle should only manage the CPU,
and device/system idle should be managed elsewhere.
Cc: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cory Maccarrone [Wed, 18 Aug 2010 04:35:46 +0000 (04:35 +0000)]
HTCHERALD: MMC, I2C, HTCPLD, SPI, TSC2046
This change adds in MMC and I2C support to the HTC Herald board, as well
as adding the HTCPLD driver for the PLD used on this phone. It also
adds in the gpio-keys entries for the front directional keys and
selector and the cursor keys on the slide-out keyboard, and gpio-leds
support for the LEDs attached to the htcpld.
Additionally, SPI bus support (using the spi100k driver) and
touchscreen support (using the ads7846 driver) were added.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP: hwmod: Handle opt clocks node using clk_add_alias
For every optional clock present per hwmod per omap-device, this function
adds an entry in the clocks list of the form <dev-id=dev_name, con-id=role>,
if an entry is already present in the list of the form <dev-id=NULL, con-id=role>.
The function is called from within the framework inside omap_device_build_ss(),
after omap_device_register.
This allows drivers to get a pointer to its optional clocks based on its role
by calling clk_get(<dev*>, <role>).
Link to discussions related to this patch:
http://www.spinics.net/lists/linux-omap/msg34809.html
Signed-off-by: Charulatha V <charu@ti.com> Signed-off-by: Partha Basak <p-basak2@ti.com> Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified loop iterator; removed the superfluous clk_get(),
using the clk_get() in clk_add_alias() instead] Signed-off-by: Paul Walmsley <paul@pwsan.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
If a module's OCP slave port is programmed to be in smartidle,
its also necessary that they have module level wakeup enabled.
Update _sysc_enable in hwmod framework to do this.
The thread "[PATCH 7/8] : Hwmod api changes" archived here:
OMAP: hwmod: Fix softreset for modules with optional clocks
Some modules (like GPIO, DSS...) require optionals clock to be enabled
in order to complete the sofreset properly.
Add a HWMOD_CONTROL_OPT_CLKS_IN_RESET flag to force all optional clocks
to be enabled before reset. Disabled them once the reset is done.
TODO:
For the moment it is very hard to understand from the HW spec, which
optional clock is needed and which one is not. So the current approach
will enable all the optional clocks.
Paul proposed a much finer approach that will allow to tag only the needed
clock in the optional clock table. This might be doable as soon as we have
a clear understanding of these dependencies.
Reported-by: Partha Basak <p-basak2@ti.com> Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@deeprootsystems.com>
OMAP: hwmod: Fix softreset status check for some new OMAP4 IPs
In OMAP3 a specific SYSSTATUS register was used to get the softreset status.
Starting in OMAP4, some IPs does not have SYSSTATUS register and instead
use the SYSC softreset bit to provide the status.
Other cases might exist:
- Some IPs like McBSP does have a softreset control but no reset status.
- Some IPs that represent subsystem, like the DSS, can contains
a reset status without softreset control. The status is the aggregation
of all the sub modules reset status.
- Add a new flag (SYSC_HAS_RESET_STATUS) to identify the new programming model
and replace the previous SYSS_MISSING, that was used to flag IP with
softreset control but without the SYSSTATUS register, with a specific
SYSS_HAS_RESET_STATUS flag.
- MCSPI and MMC contains both programming models, so the legacy one
will be prevented by removing the syss offset field that become useless.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Rajendra Nayak <rnayak@ti.com>
Paul Walmsley [Tue, 21 Sep 2010 16:34:11 +0000 (10:34 -0600)]
OMAP: hwmod: add an hardreset API for use by other core code
Expose an hardreset API from hwmod in order to assert / deassert all the
individual reset lines that belong to an hwmod. This API is needed by
some of the more complicated processor drivers, e.g., DSP/Bridge,
Syslink, etc.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com>
Force the softreset of every IPs during the _setup phase.
IPs that cannot support softreset or that should not
be reset must set the HWMOD_INIT_NO_RESET flag in the
hwmod struct.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Most processor IPs does have a hardreset signal controlled by the PRM.
This is different of the softreset used for local IP reset from the
SYSCONFIG register.
The granularity can be much finer than orginal HWMOD, for ex, the IVA
hwmod contains 3 reset lines, the IPU 3 as well, the DSP 2...
Since this granularity is needed by the driver, we have to ensure
than one hwmod exist for each hardreset line.
- Store reset lines as hwmod resources that a driver can query by name like
an irq or sdma line.
- Add two functions for asserting / deasserting reset lines in hwmods
processor that require manual reset control.
- Add one functions to get the current reset state.
- If an hwmod contains only one line, an automatic assertion / de-assertion
is done.
-> de-assert the hardreset line only during enable from disable transition
-> assert the hardreset line only during shutdown
Note: The hwmods with hardreset line and HWMOD_INIT_NO_RESET flag must be
kept in INITIALIZED state.
They can be properly enabled only if the hardreset line is de-asserted
before.
For information here is the list of IPs with HW reset control
on an OMAP4430 device:
RM_CPU0_CPU0_RSTCTRL
RM_CPU1_CPU1_RSTCTRL
0,0,'RST','RW','0','Cortex A9 CPU0&1 warm local reset control'
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made the hardreset functions static; moved the register
twiddling into prm*.c functions in previous patches; changed the
function names to conform with hwmod practice] Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Rajendra Nayak <rnayak@ti.com>
Paul Walmsley [Tue, 21 Sep 2010 16:34:10 +0000 (10:34 -0600)]
OMAP2/3: PRM: add module hard reset support
This patch adds hard-reset support for processor modules (e.g., DSP, IVA)
on OMAP2/3 platforms. It's based on the OMAP4 hard-reset support that Benoît
developed in the previous patch.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com>
Most processor modules (e.g., DSP, IVA, IPU) on OMAPs can be reset
under the control of the PRM. This patch adds an API for this purpose
for OMAP4 devices:
int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);
This API is intended to be used only by the hwmod code - a subsequent
patch will add that support to hwmod.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Benoît Cousson <b-cousson@ti.com> Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4: prcm: Add temporarily helper functions for rmw and read inside the PRM
Since OMAP4 is using an absolute address, the current PRM accessors
are not useable.
OMAP4 adaptation for these API are currently ongoing, so define temp
version until the proper ones are defined.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Tue, 21 Sep 2010 16:34:09 +0000 (10:34 -0600)]
OMAP: hwmod: separate list locking and hwmod hardware locking
Currently omap_hwmod_mutex is being used to protect both the list
access/modification and concurrent access to hwmod functions. This
patch separates these two types of locking.
First, omap_hwmod_mutex is used only to protect access and
modification of omap_hwmod_list. Also cleaned up some comments
referring to this mutex that are no longer needed.
Then, for protecting concurrent access to hwmod functions, use a
per-hwmod mutex. This protects concurrent access to a single hwmod,
but would allow concurrent access to different hwmods.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: added structure documentation; changed mutex variable
name] Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 platform has different register bits for Warm and Cold Resets.
Write one into appropriate bits.
Signed-off-by: Rajeev Kulkarni <rajeevk@ti.com> Cc: Leed Aguilar <leed.aguilar@ti.com>
[b-cousson@ti.com: Change the define with the proper one from omap4 headers] Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP: hwmod: Do not disable clocks if hwmod already in idle
The disable function was disabling clocks and dependencies
from both enable and idle state. Since idle function is already
disabling both, an enable -> idle -> disable sequence will
try to disable twice the clocks and thus generate a
"Trying disable clock XXX with 0 usecount" warning.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Thu, 17 Jun 2010 22:48:43 +0000 (15:48 -0700)]
OMAP1: PM: add simple runtime PM layer to manage clocks
On OMAP1, we do not have omap_device + omap_hwmod to manage the
device-specific idle, enable and shutdown. Instead, just
enable/disable device clocks automatically at the runtime PM level.
This allows drivers to not have any OMAP1 specific clock management
and allows them to simply use the runtime PM API to manage clocks.
Kevin Hilman [Fri, 6 Nov 2009 03:06:01 +0000 (19:06 -0800)]
OMAP2+: PM: initial runtime PM core support
Implement the new runtime PM framework as a thin layer on top of the
omap_device API. OMAP specific runtime PM methods are registered with
the as custom methods on the platform_bus.
In order to determine if a device is an omap_device, its parent device
is checked. All omap_devices have a new 'omap_device_parent_ device
as their parent device, so checking for this parent is used to check
for valid omap_devices. If a device is an omap_device, then the
appropriate omap_device functions are called for it. If not, only the
generic runtime PM functions are called.
Device driver's ->runtime_idle() hook is called when the runtime PM
usecount reaches zero for that device. Driver's ->runtime_suspend()
hooks are called just before the device is disabled (via
omap_device_idle()), and device driver ->runtime_resume() hooks are
called just after device has been enabled (via omap_device_enable().)
OMAP4 build support from Rajendra Nayak <rnayak@ti.com>.
OMAP2 build support from Charulatha V <charu@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com> Cc: Charulatha V <charu@ti.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Thara Gopinath [Thu, 12 Aug 2010 08:22:25 +0000 (13:52 +0530)]
OMAP: PM debugfs removing OMAP3 hardcodings.
This patch removes omap3 hardcodings from pm-debug.c
so that enabling PM debugfs support does break compilation
for other OMAP's. This is a preparatory patch for supporting
OMAP4 pm entries through PM debugfs.
Signed-off-by: Thara Gopinath <thara@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Dan Carpenter [Mon, 6 Sep 2010 12:32:30 +0000 (14:32 +0200)]
Staging: vt6655: fix buffer overflow
"param->u.wpa_associate.wpa_ie_len" comes from the user. We should
check it so that the copy_from_user() doesn't overflow the buffer.
Also further down in the function, we assume that if
"param->u.wpa_associate.wpa_ie_len" is set then "abyWPAIE[0]" is
initialized. To make that work, I changed the test here to say that if
"wpa_ie_len" is set then "wpa_ie" has to be a valid pointer or we return
-EINVAL.
Oddly, we only use the first element of the abyWPAIE[] array. So I
suspect there may be some other issues in this function.
The netfilter hook seems to be misused and may leak skbs in situations
when NF_HOOK returns NF_STOLEN. It may not filter everything as
expected. Also the ethernet bridge tables are not yet capable to
understand batman-adv packet correctly.
It was only added for testing purposes and can be removed again.
Mika Westerberg [Sat, 4 Sep 2010 07:23:23 +0000 (10:23 +0300)]
serial: amba-pl010: fix set_ldisc
Commit d87d9b7d1 ("tty: serial - fix tty referencing in set_ldisc") changed
set_ldisc to take ldisc number as parameter. This patch fixes AMBA PL010 driver
according the new prototype.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi> Cc: Alan Cox <alan@linux.intel.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TIOCGICOUNT device ioctl in both mos7720.c and mos7840.c allows
unprivileged users to read uninitialized stack memory, because the
"reserved" member of the serial_icounter_struct struct declared on the
stack is not altered or zeroed before being copied back to the user.
This patch takes care of it.
Ming Lei [Mon, 6 Sep 2010 15:27:09 +0000 (23:27 +0800)]
USB: otg: twl4030: fix phy initialization(v1)
Commit 461c317705eca5cac09a360f488715927fd0a927(into 2.6.36-v3)
is put forward to power down phy if no usb cable is connected,
but does introduce the two issues below:
1), phy is not into work state if usb cable is connected
with PC during poweron, so musb device mode is not usable
in such case, follows the reasons:
-twl4030_phy_resume is not called, so
regulators are not enabled
i2c access are not enabled
usb mode not configurated
2), The kernel warings[1] of regulators 'unbalanced disables'
is caused if poweron without usb cable connected
with PC or b-device.
This patch fixes the two issues above:
-power down phy only if no usb cable is connected with PC
and b-device
-do phy initialization(via __twl4030_phy_resume) if usb cable
is connected with PC(vbus event) or another b-device(ID event) in
twl4030_usb_probe.
This patch also doesn't put VUSB3V1 LDO into active mode in
twl4030_usb_ldo_init until VBUS/ID change detected, so we can
save more power consumption than before.
This patch is verified OK on Beagle board either connected with
usb cable or not when poweron.
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <me@felipebalbi.com> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: musb_debugfs: don't use the struct file private_data field with seq_files
seq_files use the private_data field of a file struct for storing a seq_file structure,
data should be stored in seq_file's own private field (e.g. file->private_data->private)
Otherwise seq_release() will free the private data when the file is closed.
Al Viro [Mon, 20 Sep 2010 14:13:25 +0000 (15:13 +0100)]
frv: double syscall restarts, syscall restart in sigreturn()
We need to make sure that only the first do_signal() to be handled on
the way out syscall will bother with syscall restarts; additionally, the
check on the "signal has user handler" path had been wrong - compare
with restart prevention in sigreturn()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 20 Sep 2010 14:13:14 +0000 (15:13 +0100)]
frv: avoid infinite loop of SIGSEGV delivery
Use force_sigsegv() rather than force_sig(SIGSEGV, ...) as the former
resets the SEGV handler pointer which will kill the process, rather than
leaving it open to an infinite loop if the SEGV handler itself caused a
SEGV signal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 20 Sep 2010 14:13:09 +0000 (15:13 +0100)]
frv: fix address verification holes in setup_frame/setup_rt_frame
a) sa_handler might be maliciously set to point to kernel memory;
blindly dereferencing it in FDPIC case is a Bad Idea(tm).
b) I'm not sure you need that set_fs(USER_DS) there at all, but if you
do, you'd better do it *before* checking the frame you've decided to
use with access_ok(), lest sigaltstack() becomes a convenient
roothole.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4969c1192d15 ("mm: fix swapin race condition") is now agreed to
be incomplete. There's a race, not very much less likely than the
original race envisaged, in which it is further necessary to check that
the swapcache page's swap has not changed.
Here's the reasoning: cast in terms of reuse_swap_page(), but probably
could be reformulated to rely on try_to_free_swap() instead, or on
swapoff+swapon.
A, faults into do_swap_page(): does page1 = lookup_swap_cache(swap1) and
comes through the lock_page(page1).
B, a racing thread of the same process, faults on the same address: does
page1 = lookup_swap_cache(swap1) and now waits in lock_page(page1), but
for whatever reason is unlucky not to get the lock any time soon.
A carries on through do_swap_page(), a write fault, but cannot reuse the
swap page1 (another reference to swap1). Unlocks the page1 (but B
doesn't get it yet), does COW in do_wp_page(), page2 now in that pte.
C, perhaps the parent of A+B, comes in and write faults the same swap
page1 into its mm, reuse_swap_page() succeeds this time, swap1 is freed.
kswapd comes in after some time (B still unlucky) and swaps out some
pages from A+B and C: it allocates the original swap1 to page2 in A+B,
and some other swap2 to the original page1 now in C. But does not
immediately free page1 (actually it couldn't: B holds a reference),
leaving it in swap cache for now.
B at last gets the lock on page1, hooray! Is PageSwapCache(page1)? Yes.
Is pte_same(*page_table, orig_pte)? Yes, because page2 has now been
given the swap1 which page1 used to have. So B proceeds to insert page1
into A+B's page_table, though its content now belongs to C, quite
different from what A wrote there.
B ought to have checked that page1's swap was still swap1.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: deal with multiple simultaneously pending signals
alpha: fix a 14 years old bug in sigreturn tracing
alpha: unb0rk sigsuspend() and rt_sigsuspend()
alpha: belated ERESTART_RESTARTBLOCK race fix
alpha: Shift perf event pending work earlier in timer interrupt
alpha: wire up fanotify and prlimit64 syscalls
alpha: kill big kernel lock
alpha: fix build breakage in asm/cacheflush.h
alpha: remove unnecessary cast from void* in assignment.
alpha: Use static const char * const where possible
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
dca: disable dca on IOAT ver.3.0 multiple-IOH platforms
netpoll: Disable IRQ around RCU dereference in netpoll_rx
sctp: Do not reset the packet during sctp_packet_config().
net/llc: storing negative error codes in unsigned short
MAINTAINERS: move atlx discussions to netdev
drivers/net/cxgb3/cxgb3_main.c: prevent reading uninitialized stack memory
drivers/net/eql.c: prevent reading uninitialized stack memory
drivers/net/usb/hso.c: prevent reading uninitialized memory
xfrm: dont assume rcu_read_lock in xfrm_output_one()
r8169: Handle rxfifo errors on 8168 chips
3c59x: Remove atomic context inside vortex_{set|get}_wol
tcp: Prevent overzealous packetization by SWS logic.
net: RPS needs to depend upon USE_GENERIC_SMP_HELPERS
phylib: fix PAL state machine restart on resume
net: use rcu_barrier() in rollback_registered_many
bonding: correctly process non-linear skbs
ipv4: enable getsockopt() for IP_NODEFRAG
ipv4: force_igmp_version ignored when a IGMPv3 query received
ppp: potential NULL dereference in ppp_mp_explode()
net/llc: make opt unsigned in llc_ui_setsockopt()
...
Jan Harkes [Sat, 18 Sep 2010 03:26:01 +0000 (23:26 -0400)]
Coda: mount hangs because of missed REQ_WRITE rename
Coda's REQ_* defines were renamed to avoid clashes with the block layer
(commit 4aeefdc69f7b: "coda: fixup clash with block layer REQ_*
defines").
However one was missed and response messages are no longer matched with
requests and waiting threads are no longer woken up. This patch fixes
this.
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
[ Also fixed up whitespace while at it -Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 18 Sep 2010 12:42:27 +0000 (08:42 -0400)]
alpha: deal with multiple simultaneously pending signals
Unlike the other targets, alpha sets _one_ sigframe and
buggers off until the next syscall/interrupt, even if
more signals are pending. It leads to quite a few unpleasant
inconsistencies, starting with SIGSEGV potentially arriving
not where it should and including e.g. mess with sigsuspend();
consider two pending signals blocked until sigsuspend()
unblocks them. We pick the first one; then, if we are hit
by interrupt while in the handler, we process the second one
as well. If we are not, and if no syscalls had been made,
we get out of the first handler and leave the second signal
pending; normally sigreturn() would've picked it anyway, but
here it starts with restoring the original mask and voila -
the second signal is blocked again. On everything else we
get both delivered consistently.
It's actually easy to fix; the only thing to watch out for
is prevention of double syscall restart. Fortunately, the
idea I've nicked from arm fix by rmk works just fine...
Testcase demonstrating the behaviour in question; on alpha
we get one or both flags set (usually one), on everything
else both are always set.
#include <signal.h>
#include <stdio.h>
int had1, had2;
void f1(int sig) { had1 = 1; }
void f2(int sig) { had2 = 1; }
main()
{
sigset_t set1, set2;
sigemptyset(&set1);
sigemptyset(&set2);
sigaddset(&set2, 1);
sigaddset(&set2, 2);
signal(1, f1);
signal(2, f2);
sigprocmask(SIG_SETMASK, &set2, NULL);
raise(1);
raise(2);
sigsuspend(&set1);
printf("had1:%d had2:%d\n", had1, had2);
}
Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Matt Turner <mattst88@gmail.com>
Al Viro [Sat, 18 Sep 2010 12:41:16 +0000 (08:41 -0400)]
alpha: fix a 14 years old bug in sigreturn tracing
The way sigreturn() is implemented on alpha breaks PTRACE_SYSCALL,
all way back to 1.3.95 when alpha has grown PTRACE_SYSCALL support.
What happens is direct return to ret_from_syscall, in order to bypass
mangling of a3 (error indicator) and prevent other mutilations of
registers (e.g. by syscall restart). That's fine, but... the entire
TIF_SYSCALL_TRACE codepath is kept separate on alpha and post-syscall
stopping/notifying the tracer is after the syscall. And the normal
path we are forcibly switching to doesn't have it.
So we end up with *one* stop in traced sigreturn() vs. two in other
syscalls. And yes, strace is visibly broken by that; try to strace
the following
#include <signal.h>
#include <stdio.h>
void f(int sig) {}
main()
{
signal(SIGHUP, f);
raise(SIGHUP);
write(1, "eeeek\n", 6);
}
and watch the show. The
close(1) = 405
in the end of strace output is coming from return value of write() (6 ==
__NR_close on alpha) and syscall number of exit_group() (__NR_exit_group ==
405 there).
The fix is fairly simple - the only thing we end up missing is the call
of syscall_trace() and we can tell whether we'd been called from the
SYSCALL_TRACE path by checking ra value. Since we are setting the
switch_stack up (that's what sys_sigreturn() does), we have the right
environment for calling syscall_trace() - just before we call
undo_switch_stack() and return. Since undo_switch_stack() will overwrite
s0 anyway, we can use it to store the result of "has it been called from
SYSCALL_TRACE path?" check. The same thing applies in rt_sigreturn().
Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Matt Turner <mattst88@gmail.com>
Al Viro [Sat, 18 Sep 2010 12:40:07 +0000 (08:40 -0400)]
alpha: unb0rk sigsuspend() and rt_sigsuspend()
Old code used to set regs->r0 and regs->r19 to force the right
return value. Leaving that after switch to ERESTARTNOHAND
was a Bad Idea(tm), since now that screws the restart - if we
hit the case when get_signal_to_deliver() returns 0, we will
step back to syscall insn, with v0 set to EINTR and a3 to 1.
The latter won't matter, since EINTR is 4, aka __NR_write.
results on alpha in immediate message to stdout...
Fix is obvious; moreover, since we don't need regs anymore, we can
switch to normal prototypes for these guys and lose the wrappers.
Even better, rt_sigsuspend() is identical to generic version in
kernel/signal.c now.
Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Matt Turner <mattst88@gmail.com>
Michael Cree [Sun, 19 Sep 2010 06:05:40 +0000 (02:05 -0400)]
alpha: Shift perf event pending work earlier in timer interrupt
Pending work from the performance event subsystem is executed in
the timer interrupt. This patch shifts the call to
perf_event_do_pending() before the call to update_process_times()
as the latter may call back into the perf event subsystem and it
is prudent to have the pending work executed first.
Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Matt Turner <mattst88@gmail.com>
All uses of the BKL on alpha are totally bogus, nothing
is really protected by this. Remove the remaining users
so we don't have to mark alpha as 'depends on BKL'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: linux-alpha@vger.kernel.org Signed-off-by: Matt Turner <mattst88@gmail.com>
Alpha SMP flush_icache_user_range() is implemented as an inline
function inside include/asm/cacheflush.h. It dereferences @current
but doesn't include linux/sched.h and thus causes build failure if
linux/sched.h wasn't included previously. Fix it by including the
needed header file explicitly.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Matt Turner <mattst88@gmail.com>
dca: disable dca on IOAT ver.3.0 multiple-IOH platforms
Direct Cache Access is not supported on IOAT ver.3.0 multiple-IOH platforms.
This patch blocks registering of dca providers when multiple IOH detected with IOAT ver.3.0.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 17 Sep 2010 23:55:03 +0000 (16:55 -0700)]
netpoll: Disable IRQ around RCU dereference in netpoll_rx
We cannot use rcu_dereference_bh safely in netpoll_rx as we may
be called with IRQs disabled. We could however simply disable
IRQs as that too causes BH to be disabled and is safe in either
case.
Thanks to John Linville for discovering this bug and providing
a patch.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: Do not reset the packet during sctp_packet_config().
sctp_packet_config() is called when getting the packet ready
for appending of chunks. The function should not touch the
current state, since it's possible to ping-pong between two
transports when sending, and that can result packet corruption
followed by skb overlfow crash.
Reported-by: Thomas Dreibholz <dreibh@iem.uni-due.de> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (lm95241) Replace rate sysfs attribute with update_interval
hwmon: (adm1031) Replace update_rate sysfs attribute with update_interval
hwmon: (w83627ehf) Use proper exit sequence
hwmon: (emc1403) Remove unnecessary hwmon_device_unregister
hwmon: (f75375s) Do not overwrite values read from registers
hwmon: (f75375s) Shift control mode to the correct bit position
hwmon: New subsystem maintainers
hwmon: (lis3lv02d) Prevent NULL pointer dereference
projects / linux-beck.git / log