Brad Volkin [Tue, 18 Feb 2014 18:15:55 +0000 (10:15 -0800)]
drm/i915: Reject commands that would store to global HWS page
PIPE_CONTROL and MI_FLUSH_DW have bits that would write to the
hardware status page. The driver stores request tracking info
there, so don't let userspace overwrite it.
v2: trailing comma fix, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Brad Volkin [Tue, 18 Feb 2014 18:15:54 +0000 (10:15 -0800)]
drm/i915: Enable PPGTT command parser checks
Various commands that access memory have a bit to determine whether
the graphics address specified in the command should use the GGTT or
PPGTT for translation. These checks ensure that the bit indicates
PPGTT translation.
Most of these checks use the existing bit-checking infrastructure.
The PIPE_CONTROL and MI_FLUSH_DW commands, however, are multi-function
commands. The GGTT/PPGTT bit is only relevant for certain uses of the
command. As such, this change also extends the bit-checking code to
include a "condition" mask and offset. If the condition mask is non-zero
then the parser only performs the bit check when the bits specified by
the condition mask/offset are also non-zero.
NOTE: At this point in the series PPGTT must be enabled for the parser
to work correctly. If it's not enabled, userspace will not be setting
the PPGTT bits the way the parser requires. VLV is the only platform
where this is a problem, so at this point, we disable parsing for VLV.
v2: whitespace and trailing commas fixes, rebased
OTC-Tracker: AXIA-4631
Change-Id: I3f4c76b6734f1956ec47e698230f97d0998ff92b Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the unecessary cast Jani spotted.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Brad Volkin [Tue, 18 Feb 2014 18:15:53 +0000 (10:15 -0800)]
drm/i915: Reject commands that explicitly generate interrupts
The driver leaves most interrupts masked during normal operation,
so there would have to be additional work to enable userspace to
safely request/receive an interrupt.
v2: trailing commas, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Brad Volkin [Tue, 18 Feb 2014 18:15:52 +0000 (10:15 -0800)]
drm/i915: Enable register whitelist checks
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM, and MI_LOAD_REGISTER_IMM
commands allow userspace access to registers. Only certain registers
should be allowed for such access, so enable checking for those commands.
Each ring gets its own register whitelist.
MI_LOAD_REGISTER_REG on HSW also allows register access but is currently
unused by userspace components. Leave it rejected.
PIPE_CONTROL and MEDIA_VFE_STATE allow register access based on certain
bits being set. Reject those as well.
v2: trailing commas, rebased
OTC-Tracker: AXIA-4631
Change-Id: Ie614a2f0eb2e5917de809e5a17957175d24cc44f Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Brad Volkin [Tue, 18 Feb 2014 18:15:48 +0000 (10:15 -0800)]
drm/i915: Reject privileged commands
The spec defines most of these commands as privileged. A few others,
like the semaphore mbox command and some display commands, are also
reserved for the driver's use. Subsequent patches relax some of
these restrictions.
v2: Rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 25 Mar 2014 01:06:00 +0000 (18:06 -0700)]
drm/i915: Allow full PPGTT with param override
When PPGTT was disabled by default, the patch also prevented the user
from overriding this behavior via module parameter. Being able to test
this on arbitrary kernels is extremely beneficial to track down the
remaining bugs. The patch that prevented this was:
Ben Widawsky [Sun, 23 Mar 2014 05:47:21 +0000 (22:47 -0700)]
drm/i915: Split out GTT specific header file
This file contains all necessary defines, prototypes and typesdefs for
manipulating GEN graphics address translation (this does not include the
legacy AGP driver)
Reiterating the comment in the header,
"Please try to maintain the following order within this file unless it
makes sense to do otherwise. From top to bottom:
1. typedefs
2. #defines, and macros
3. structure definitions
4. function prototypes
Within each section, please try to order by generation in ascending
order, from top to bottom (ie. GEN6 on the top, GEN8 on the bottom)."
I've made some minor cleanups, and fixed a couple of typos while here -
but there should be no functional changes.
The purpose of the patch is to reduce clutter in our main header file,
making room for new growth, and make documentation of our interfaces
easier by splitting things out.
With a little more work, like making i915_gtt a pointer, we could
potentially completely isolate this header from i915_drv.h. At the
moment however, I don't think it's worth the effort.
Personally, I would have liked to put the PTE encoding functions in this
file too, but I didn't want to rock the boat too much.
A similar patch has been in use on my machine for some time. This exact
patch though has only been compile tested.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 18 Mar 2014 09:26:04 +0000 (10:26 +0100)]
drm/i915: make semaphore signaller detection more robust
Extract all this logic into a new helper function
semaphore_wait_to_signaller_ring because:
- The current code has way too much magic.
- The current code doesn't look at bi16, which encodes VECS signallers
on HSW. Those are just added after the fact, so can't be encoded in
a neat formula.
- The current logic can't blow up since it limits its value range
sufficiently, but that's a bit too tricky to rely on in my opinion.
Especially when we start to add bdw support.
- I'm not a big fan of the explicit ring->semaphore_register list, but
I think it's more robust to use the same mapping both when
constructing the semaphore commands and when decoding them.
- Finally add a FIXME comment about lack of broadwell support here,
like in the earlier ipehr semaphore cmd detection function.
Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Actually drop the untrue claim in the commit message Chris
pointed out.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 14 Mar 2014 23:08:56 +0000 (00:08 +0100)]
drm/i915: Add FIXME for bdw semaphore detection in hancheck
Currently not an issue since we don't emit sempahores, but better
not forget about those.
As a little prep work extract the ipehr decoding for cleaner control
flow. And apply a bit of polish.
Cc: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 21 Mar 2014 17:18:54 +0000 (17:18 +0000)]
drm/i915: Rename GFX_TLB_INVALIDATE_ALWAYS
The documentation calls this GFX_MODE bit "Flush TLB invalidate Mode".
However, that is not a good name for an enable bit as it doesn't make it
clear what is enabled. An even worse name is GFX_TLB_INVALIDATE_ALWAYS
as enabling that bit actually prevents the TLB from being invalidated at
every flush. This leads to great confusion when reading code and
proposed patches. To get around this try to bake in what is enabled by
setting the bit and call it GFX_TLB_INVALIDATE_EXPLICIT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: "Gupta, Sourab" <sourab.gupta@intel.com> Acked-by: "Gupta, Sourab" <sourab.gupta@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 1 Apr 2014 17:55:13 +0000 (14:55 -0300)]
drm/i915: don't get/put runtime PM at the debugfs forcewake file
Because gen6_gt_force_wake_{get,put} should already be responsible for
getting/putting runtime PM. If we keep these calls, debugfs will not
be testing the get/put calls of the forcewake functions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 1 Apr 2014 17:55:12 +0000 (14:55 -0300)]
drm/i915: fix WARNs when reading DDI state while suspended
If runtime PM is enabled and we unset all modes, we will runtime
suspend after __intel_set_mode() , then function
intel_modeset_check_state() will try to read the HW state while it is
suspended and trigger lots of WARNs because it shouldn't be reading
registers.
So on this patch we make intel_ddi_connector_get_hw_state() return
false in case the power domain is disabled, and we also make
intel_display_power_enabled() return false in case the device is
suspended. Notice that we can't just use
intel_display_power_enabled_sw() because while the driver is being
initialized the power domain refcounts are not reflecting the real
state of the hardware.
Just for reference, I have previously published an alternate patch for
this problem, called "drm/i915: get runtime PM at intel_set_mode".
Testcase: igt/pm_pc8 Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 1 Apr 2014 17:55:11 +0000 (14:55 -0300)]
drm/i915: don't read cursor registers on powered down pipes
At i915_display_info, don't call cursor_position() for a disabled
CRTC, since the CRTC may be on a powered down pipe, and this will
cause "Unclaimed register before interrupt" error messages.
Testcase: igt/pm_pc8/debugfs-read Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 1 Apr 2014 17:55:07 +0000 (14:55 -0300)]
drm/i915: don't schedule force_wake_timer at gen6_read
So far force_wake_timer was only used by gen6_gt_force_wake_put. Since
we always had balanced gen6_gt_force_wake_get/put calls, we could
guarantee balanced calls to intel_runtime_pm_get/put.
Commit 8232644ccf099548710843e97360a3fcd6d28e04, "drm/i915: Convert
the forcewake worker into a timer func" started scheduling the
force_wake_timer at gen6_read, which resulted in an unbalanced
runtime_pm refcount.
So this commit just reverts to the old behavior until we can find a
proper way to used delayed force_wake from the register read/write
macros without leaving the runtime_pm refcounts unbalanced and without
runtime suspending the driver while forcewake is active.
Testcase: igt/pm_pc8/rte
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76544 Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 31 Mar 2014 12:10:44 +0000 (15:10 +0300)]
drm/i915: vlv: reserve the GT power context only once during driver init
Atm we reserve/allocate and free the power context during GT power
enable/disable time. There is no need to do this, we can reserve/allocate
the buffer once during driver loading and free it during driver cleanup.
The re-reservation can also fail in case the driver previously manages to
allocate something on the given fixed address.
The buffer isn't exepected to move even if allocated by the BIOS, for
safety add an assert to check this assumption.
This also fixed a bug for Ville, where re-reserving the context failed
during a GPU reset (I assume because something else got allocated on its
fixed address).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 28 Mar 2014 08:03:34 +0000 (08:03 +0000)]
drm/i915: Mask PM/RPS interrupt generation based on activity
The speculation is that we can conserve more power by masking off
the interrupts at source (PMINTRMSK) rather than filtering them by the
up/down thresholds (RPINTLIM). We can select which events we know will
be active based on the current frequency versus our imposed range, i.e.
if at minimum, we know we will not want to generate any more
down-interrupts and vice versa.
v2: We only need the TIMEOUT when above min frequency.
v3: Tweak VLV at the same time
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by:Deepak S <deepak.s@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Thu, 27 Mar 2014 08:24:20 +0000 (08:24 +0000)]
drm/i915: Refactor gen6_set_rps
What used to be a short-circuit now needs to adjust interrupt masking in
response to user requests for changing the min/max allowed frequencies.
This is currently done by a special case and early return, but the next
patch adds another common action to take, so refactor the code to reduce
duplication.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by:Deepak S <deepak.s@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The partial application of interrupt masking without regard to other
pathways for adjusting the RPS frequency results in completely disabling
the PM interrupts. This leads to excessive power consumption as the GPU
is kept at max clocks (until the failsafe mechanism fires of explicitly
downclocking the GPU when all requests are idle). Or equally as bad for
the UX, the GPU is kept at minimum clocks and prevented from upclocking
in response to a requirement for more power.
Testcase: pm_rps/blocking Cc: Deepak S <deepak.s@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by:Deepak S <deepak.s@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 28 Mar 2014 21:29:31 +0000 (23:29 +0200)]
drm/i915: Fix the interlace mode selection for gmch platforms
PIPECONF_INTERLACE_W_FIELD_INDICATION is only meant to be used for sdvo
since it implies a slightly weird vsync shift of htotal/2. For everything
else we should use PIPECONF_INTERLACE_W_SYNC_SHIFT and let the value in
the VSYNCSHIFT register take effect.
The only exception is gen3 simply because VSYNCSHIFT didn't exist yet.
Gen2 doesn't support interlaced modes at all, so we can drop the
explicit gen2 checks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 28 Mar 2014 21:29:30 +0000 (23:29 +0200)]
drm/i915: Program VSYNCSHIFT in a more consistent manner
When interlaced sdvo output is used, vsyncshift should supposedly
be (htotal-1)/2. In reality PIPECONF/TRANSCONF will override it by
using the legacy vsyncshift interlace mode which causes the hardware
to ignore the VSYNCSHIFT register.
The only odd thing here is that on PCH platforms we program the
VSYNCSHIFT on both CPU and PCH, and it's not entirely clear if both
sides have to agree on the value or not. On the CPU side there's no
way to override the value via PIPECONF anymore, so if we want to make
the CPU side agree with the PCH side, we should probably program the
approriate value into VSYNCSHIFT manually. So let's do that, but for
now leave the PCH side to still use the legacy interlace mode in
TRANSCONF.
We can also drop the gen2 check since gen2 doesn't support interlaced
modes at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Thu, 27 Mar 2014 18:56:08 +0000 (11:56 -0700)]
drm/i915/vlv: use W_SYNC_SHIFT for interlaced modes on VLV
This makes HDMI testers happier on VLV platforms. It may be that we
need it for any non-SVO platform, but I don't have any tests to back
that up, so I'm leaving other pre-ILK platforms alone for now.
Tested-by: "Clint Taylor <clinton.a.taylor@intel.com>" Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74964 Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 26 Mar 2014 22:42:53 +0000 (23:42 +0100)]
drm/i915: restrict vt-d stolen memory workaround to pre-gen8
We want future generations to at least attempt to use all features, so
restrict the stolen memory disabling when vt-d is enabled to the
latest generation we have reports for. Which is a HSW per the original
report.
Also once we get a bit a hold of some of the mysterious framebuffer in
stolen memory issues that still haunt bugzilla, we should probably
drop this hack again and see what happens.
drm/i915: Disable stolen memory when DMAR is active
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jani Nikula <jani.nikula@intel.com> Cc: David Woodhouse <dwmw2@infradead.org>
References: https://bugs.freedesktop.org/show_bug.cgi?id=68535 Acked-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Mon, 31 Mar 2014 00:26:08 +0000 (17:26 -0700)]
Merge branch 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Switch mnt_hash to hlist, turning the races between __lookup_mnt() and
hash modifications into false negatives from __lookup_mnt() (instead
of hangs)"
On the false negatives from __lookup_mnt():
"The *only* thing we care about is not getting stuck in __lookup_mnt().
If it misses an entry because something in front of it just got moved
around, etc, we are fine. We'll notice that mount_lock mismatch and
that'll be it"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch mnt_hash to hlist
don't bother with propagate_mnt() unless the target is shared
keep shadowed vfsmounts together
resizable namespace.c hashes
Linus Torvalds [Mon, 31 Mar 2014 00:20:40 +0000 (17:20 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Some more updates for the input subsystem.
You will get a fix for race in mousedev that has been causing quite a
few oopses lately and a small fixup for force feedback support in
evdev"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mousedev - fix race when creating mixed device
Input: don't modify the id of ioctl-provided ff effect on upload failure
Eric Paris [Sun, 30 Mar 2014 23:07:54 +0000 (19:07 -0400)]
AUDIT: Allow login in non-init namespaces
It its possible to configure your PAM stack to refuse login if audit
messages (about the login) were unable to be sent. This is common in
many distros and thus normal configuration of many containers. The PAM
modules determine if audit is enabled/disabled in the kernel based on
the return value from sending an audit message on the netlink socket.
If userspace gets back ECONNREFUSED it believes audit is disabled in the
kernel. If it gets any other error else it refuses to let the login
proceed.
Just about ever since the introduction of namespaces the kernel audit
subsystem has returned EPERM if the task sending a message was not in
the init user or pid namespace. So many forms of containers have never
worked if audit was enabled in the kernel.
BUT if the container was not in net_init then the kernel network code
would send ECONNREFUSED (instead of the audit code sending EPERM). Thus
by pure accident/dumb luck/bug if an admin configured the PAM stack to
reject all logins that didn't talk to audit, but then ran the login
untility in the non-init_net namespace, it would work!! Clearly this was
a bug, but it is a bug some people expected.
With the introduction of network namespace support in 3.14-rc1 the two
bugs stopped cancelling each other out. Now, containers in the
non-init_net namespace refused to let users log in (just like PAM was
configfured!) Obviously some people were not happy that what used to let
users log in, now didn't!
This fix is kinda hacky. We return ECONNREFUSED for all non-init
relevant namespaces. That means that not only will the old broken
non-init_net setups continue to work, now the broken non-init_pid or
non-init_user setups will 'work'. They don't really work, since audit
isn't logging things. But it's what most users want.
In 3.15 we should have patches to support not only the non-init_net
(3.14) namespace but also the non-init_pid and non-init_user namespace.
So all will be right in the world. This just opens the doors wide open
on 3.14 and hopefully makes users happy, if not the audit system...
Reported-by: Andre Tomt <andre@tomt.net> Reported-by: Adam Richter <adam_richter2004@yahoo.com> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Theodore Ts'o [Sun, 30 Mar 2014 14:20:01 +0000 (10:20 -0400)]
ext4: atomically set inode->i_flags in ext4_set_inode_flags()
Use cmpxchg() to atomically set i_flags instead of clearing out the
S_IMMUTABLE, S_APPEND, etc. flags and then setting them from the
EXT4_IMMUTABLE_FL, EXT4_APPEND_FL flags, since this opens up a race
where an immutable file has the immutable flag cleared for a brief
window of time.
Al Viro [Fri, 21 Mar 2014 01:10:51 +0000 (21:10 -0400)]
switch mnt_hash to hlist
fixes RCU bug - walking through hlist is safe in face of element moves,
since it's self-terminating. Cyclic lists are not - if we end up jumping
to another hash chain, we'll loop infinitely without ever hitting the
original list head.
[fix for dumb braino folded]
Spotted by: Max Kellermann <mk@cm4all.com> Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 21 Mar 2014 14:14:08 +0000 (10:14 -0400)]
don't bother with propagate_mnt() unless the target is shared
If the dest_mnt is not shared, propagate_mnt() does nothing -
there's no mounts to propagate to and thus no copies to create.
Might as well don't bother calling it in that case.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 28 Feb 2014 18:46:44 +0000 (13:46 -0500)]
resizable namespace.c hashes
* switch allocation to alloc_large_system_hash()
* make sizes overridable by boot parameters (mhash_entries=, mphash_entries=)
* switch mountpoint_hashtable from list_head to hlist_head
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 29 Mar 2014 22:01:09 +0000 (15:01 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"A late breaking fix from John. (The bug fixed has a hard lockup
potential, but that was not observed, warnings were)"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Revert to calling clock_was_set_delayed() while in irq context
Dmitry Torokhov [Thu, 6 Mar 2014 20:57:24 +0000 (12:57 -0800)]
Input: mousedev - fix race when creating mixed device
We should not be using static variable mousedev_mix in methods that can be
called before that singleton gets assigned. While at it let's add open and
close methods to mousedev structure so that we do not need to test if we
are dealing with multiplexor or normal device and simply call appropriate
method directly.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=71551
Input: don't modify the id of ioctl-provided ff effect on upload failure
If a new (id == -1) ff effect was uploaded from userspace,
ff-core.c::input_ff_upload() will have assigned a positive number to the
new effect id. Currently, evdev.c::evdev_do_ioctl() will save this new id
to userspace, regardless of whether the upload succeeded or not.
On upload failure, this can be confusing because the dev->ff->effects[]
array will not contain an element at the index of that new effect id.
This patch fixes this by leaving the id unchanged after upload fails.
Note: Unfortunately applications should still expect changed effect id for
quite some time.
This has been discussed on:
http://www.mail-archive.com/linux-input@vger.kernel.org/msg08513.html
("ff-core effect id handling in case of a failed effect upload")
Alex Elder [Tue, 25 Mar 2014 13:36:02 +0000 (15:36 +0200)]
rbd: drop an unsafe assertion
Olivier Bonvalet reported having repeated crashes due to a failed
assertion he was hitting in rbd_img_obj_callback():
Assertion failure in rbd_img_obj_callback() at line 2165:
rbd_assert(which >= img_request->next_completion);
With a lot of help from Olivier with reproducing the problem
we were able to determine the object and image requests had
already been completed (and often freed) at the point the
assertion failed.
There was a great deal of discussion on the ceph-devel mailing list
about this. The problem only arose when there were two (or more)
object requests in an image request, and the problem was always
seen when the second request was being completed.
The problem is due to a race in the window between setting the
"done" flag on an object request and checking the image request's
next completion value. When the first object request completes, it
checks to see if its successor request is marked "done", and if
so, that request is also completed. In the process, the image
request's next_completion value is updated to reflect that both
the first and second requests are completed. By the time the
second request is able to check the next_completion value, it
has been set to a value *greater* than its own "which" value,
which caused an assertion to fail.
Fix this problem by skipping over any completion processing
unless the completing object request is the next one expected.
Test only for inequality (not >=), and eliminate the bad
assertion.
Tested-by: Olivier Bonvalet <ob@daevel.fr> Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Sage Weil <sage@inktank.com> Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>
1) We've discovered a common error in several networking drivers, they
put VLAN offload features into ->vlan_features, which would suggest
that they support offloading 2 or more levels of VLAN encapsulation.
Not only do these devices not do that, but we don't have the
infrastructure yet to handle that at all.
Fixes from Vlad Yasevich.
2) Fix tcpdump crash with bridging and vlans, also from Vlad.
3) Some MAINTAINERS updates for random32 and bonding.
4) Fix late reseeds of prandom generator, from Sasha Levin.
6) Fix deadlock in openvswitch, from Flavio Leitner.
7) get_timewait4_sock() doesn't report delay times correctly, fix from
Eric Dumazet.
8) Duplicate address detection and addrconf verification need to run in
contexts where RTNL can be obtained. Move them to run from a
workqueue. From Hannes Frederic Sowa.
9) Fix route refcount leaking in ip tunnels, from Pravin B Shelar.
10) Don't return -EINTR from non-blocking recvmsg() on AF_UNIX sockets,
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
vlan: Warn the user if lowerdev has bad vlan features.
veth: Turn off vlan rx acceleration in vlan_features
ifb: Remove vlan acceleration from vlan_features
qlge: Do not propaged vlan tag offloads to vlans
bridge: Fix crash with vlan filtering and tcpdump
net: Account for all vlan headers in skb_mac_gso_segment
MAINTAINERS: bonding: change email address
MAINTAINERS: bonding: change email address
ipv6: move DAD and addrconf_verify processing to workqueue
tcp: fix get_timewait4_sock() delay computation on 64bit
openvswitch: fix a possible deadlock and lockdep warning
bridge: Fix handling stacked vlan tags
bridge: Fix inabillity to retrieve vlan tags when tx offload is disabled
vhost: validate vhost_get_vq_desc return value
vhost: fix total length when packets are too short
random32: avoid attempt to late reseed if in the middle of seeding
random32: assign to network folks in MAINTAINERS
net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset
core, nfqueue, openvswitch: Orphan frags in skb_zerocopy and handle errors
vlan: Set hard_header_len according to available acceleration
...
Vlad Yasevich [Fri, 28 Mar 2014 02:14:49 +0000 (22:14 -0400)]
vlan: Warn the user if lowerdev has bad vlan features.
Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Fri, 28 Mar 2014 02:14:46 +0000 (22:14 -0400)]
qlge: Do not propaged vlan tag offloads to vlans
qlge driver turns off NETIF_F_HW_CTAG_FILTER, but forgets to
turn off HW_CTAG_TX and HW_CTAG_RX on vlan devices. With the
current settings, q-in-q will only generate a single vlan header.
Remember to mask off CTAG_TX and CTAG_RX features in vlan_features.
CC: Shahed Shaikh <shahed.shaikh@qlogic.com> CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> CC: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Fri, 28 Mar 2014 01:51:18 +0000 (21:51 -0400)]
bridge: Fix crash with vlan filtering and tcpdump
When the vlan filtering is enabled on the bridge, but
the filter is not configured on the bridge device itself,
running tcpdump on the bridge device will result in a
an Oops with NULL pointer dereference. The reason
is that br_pass_frame_up() will bypass the vlan
check because promisc flag is set. It will then try
to get the table pointer and process the packet based
on the table. Since the table pointer is NULL, we oops.
Catch this special condition in br_handle_vlan().
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> CC: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Thu, 27 Mar 2014 21:26:18 +0000 (17:26 -0400)]
net: Account for all vlan headers in skb_mac_gso_segment
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 28 Mar 2014 20:57:13 +0000 (13:57 -0700)]
Merge branch 'akpm' (patches from Andrew Morton)
Merge two fixes from Andrew Morton:
"The x86 fix should come from x86 guys but they appear to be
conferencing or otherwise distracted.
The ocfs2 fix is a bit of a mess - the code runs into an immediate
NULL deref and we're trying to work out how this got through test and
review, but we haven't heard from Goldwyn in the past few days.
Sasha's patch fixes the oops, but the feature as a whole is probably
broken. So this is a stopgap for 3.14 - I'll aim to get the real
fixes into 3.14.x"
* emailed patches from Andrew Morton akpm@linux-foundation.org>:
x86: fix boot on uniprocessor systems
ocfs2: check if cluster name exists before deref
Artem Fetishev [Fri, 28 Mar 2014 20:33:39 +0000 (13:33 -0700)]
x86: fix boot on uniprocessor systems
On x86 uniprocessor systems topology_physical_package_id() returns -1
which causes rapl_cpu_prepare() to leave rapl_pmu variable uninitialized
which leads to GPF in rapl_pmu_init().
See arch/x86/kernel/cpu/perf_event_intel_rapl.c.
It turns out that physical_package_id and core_id can actually be
retreived for uniprocessor systems too. Enabling them also fixes
rapl_pmu code.
Signed-off-by: Artem Fetishev <artem_fetishev@epam.com> Cc: Stephane Eranian <eranian@google.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sasha Levin [Fri, 28 Mar 2014 20:33:38 +0000 (13:33 -0700)]
ocfs2: check if cluster name exists before deref
Commit c74a3bdd9b52 ("ocfs2: add clustername to cluster connection") is
trying to strlcpy a string which was explicitly passed as NULL in the
very same patch, triggering a NULL ptr deref.
ipv6: move DAD and addrconf_verify processing to workqueue
addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.
A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.
To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.
(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).
addrconf_verify_lock is removed, too. After the transition it is not
needed any more.
As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.
Hunks and backtrace stolen from a patch by Stephen Hemminger.
Reported-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 27 Mar 2014 14:19:19 +0000 (07:19 -0700)]
tcp: fix get_timewait4_sock() delay computation on 64bit
It seems I missed one change in get_timewait4_sock() to compute
the remaining time before deletion of IPV4 timewait socket.
This could result in wrong output in /proc/net/tcp for tm->when field.
Fixes: 96f817fedec4 ("tcp: shrink tcp6_timewait_sock by one cache line") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Flavio Leitner [Thu, 27 Mar 2014 14:05:34 +0000 (11:05 -0300)]
openvswitch: fix a possible deadlock and lockdep warning
There are two problematic situations.
A deadlock can happen when is_percpu is false because it can get
interrupted while holding the spinlock. Then it executes
ovs_flow_stats_update() in softirq context which tries to get
the same lock.
The second sitation is that when is_percpu is true, the code
correctly disables BH but only for the local CPU, so the
following can happen when locking the remote CPU without
disabling BH:
Toshiaki Makita [Thu, 27 Mar 2014 12:46:56 +0000 (21:46 +0900)]
bridge: Fix handling stacked vlan tags
If a bridge with vlan_filtering enabled receives frames with stacked
vlan tags, i.e., they have two vlan tags, br_vlan_untag() strips not
only the outer tag but also the inner tag.
br_vlan_untag() is called only from br_handle_vlan(), and in this case,
it is enough to set skb->vlan_tci to 0 here, because vlan_tci has already
been set before calling br_handle_vlan().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Thu, 27 Mar 2014 12:46:55 +0000 (21:46 +0900)]
bridge: Fix inabillity to retrieve vlan tags when tx offload is disabled
Bridge vlan code (br_vlan_get_tag()) assumes that all frames have vlan_tci
if they are tagged, but if vlan tx offload is manually disabled on bridge
device and frames are sent from vlan device on the bridge device, the tags
are embedded in skb->data and they break this assumption.
Extract embedded vlan tags and move them to vlan_tci at ingress.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vhost fails to validate negative error code
from vhost_get_vq_desc causing
a crash: we are using -EFAULT which is 0xfffffff2
as vector size, which exceeds the allocated size.
Sasha Levin [Fri, 28 Mar 2014 16:38:42 +0000 (17:38 +0100)]
random32: avoid attempt to late reseed if in the middle of seeding
Commit 4af712e8df ("random32: add prandom_reseed_late() and call when
nonblocking pool becomes initialized") has added a late reseed stage
that happens as soon as the nonblocking pool is marked as initialized.
This fails in the case that the nonblocking pool gets initialized
during __prandom_reseed()'s call to get_random_bytes(). In that case
we'd double back into __prandom_reseed() in an attempt to do a late
reseed - deadlocking on 'lock' early on in the boot process.
Instead, just avoid even waiting to do a reseed if a reseed is already
occuring.
Fixes: 4af712e8df99 ("random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized") Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 28 Mar 2014 20:03:00 +0000 (13:03 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Updates to Synaptics touchpad to better cope with devices in Lenovo
laptops, and a couple more fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - add manual min/max quirk for ThinkPad X240
Input: synaptics - add manual min/max quirk
Input: cypress_ps2 - don't report as a button pads
Input: da9052_onkey - use correct register bit for key status
Input: adp5588-keys - get value from data out when dir is out
Linus Torvalds [Fri, 28 Mar 2014 17:58:10 +0000 (10:58 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I didn't want these to wait for stable cycle.
The nouveau and radeon ones are the same problem, where the runtime pm
stuff broke non-runtime pm managed secondary GPUs.
The udl fix is for an oops on unplug, and the i915 fix is for a
regression on Sandybridge even though it may break haswell (regression
wins)"
Daniel Vetter comments:
"My apologies for the i915 regression fumble, that thing somehow fell
through the cracks here for almost half a year :( Imo that's more than
enough flailing to just go ahead with the revert, and the re-broken
hsw should get peoples attention ..."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Undo gtt scratch pte unmapping again
drm/radeon: fix runtime suspend breaking secondary GPUs
drm/nouveau: fail runtime pm properly.
drm/udl: take reference to device struct for dma-bufs
Linus Torvalds [Fri, 28 Mar 2014 17:52:05 +0000 (10:52 -0700)]
Merge tag 'stable/for-linus-3.14-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bugfixes from David Vrabel:
"Fix two bugs that cause x86 PV guest crashes.
1. Ballooning a 32-bit guest would eventually crash it.
2. Revert a broken fix for a regression with NUMA_BALACING. The bad
fix caused PV guests to crash after migration. This is not ideal
but unpicking the madness that is _PAGE_NUMA == _PAGE_PROTNONE will
take a while longer"
* tag 'stable/for-linus-3.14-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Revert "xen: properly account for _PAGE_NUMA during xen pte translations"
xen/balloon: flush persistent kmaps in correct position
Chris Wilson [Fri, 21 Mar 2014 12:05:47 +0000 (12:05 +0000)]
drm/i915: Split 64bit hexadecimal addresses to make them easier to read
Broadwell introduces large address spaces, greater than 32bits in width.
These require that we then store and print 64bit values. If we were to
zero pad them out to 16 hexadecimal places, we have to carefully count
the leading zeroes - which is easy to make a mistake. Conversely, if we
do not zero pad out to 16, but keep it padding to 8 hexadecimal places,
it is very easy to miss an address that is actually larger than 4GiB. A
suggested compromise is to insert a space between the upper and lower
dwords of the address so that we can continue with our accustom 32bit
parser. (Alternatively, we could do the equivalent in our userspace
decoder.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 21 Mar 2014 12:41:53 +0000 (12:41 +0000)]
drm/i915: Broadwell expands ACTHD to 64bit
As Broadwell has an increased virtual address size, it requires more
than 32 bits to store offsets into its address space. This includes the
debug registers to track the current HEAD of the individual rings, which
may be anywhere within the per-process address spaces. In order to find
the full location, we need to read the high bits from a second register.
We then also need to expand our storage to keep track of the larger
address.
v2: Carefully read the two registers to catch wraparound between
the reads.
v3: Use a WARN_ON rather than loop indefinitely on an unstable
register read.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ben Widawsky <benjamin.widawsky@intel.com> Cc: Timo Aaltonen <tjaalton@ubuntu.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Drop spurious hunk which conflicted.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 26 Mar 2014 12:38:15 +0000 (12:38 +0000)]
drm/i915: Recompute WM when the cursor size changes
If the cursor width is changed, we may need to recompute our WM to
prevent untold flickering. We hope that the registers are flushed on the
same vblank to prevent underruns...
Cc: Damien Lespiau <damien.lespiau@intel.com> Cc: Sagar Kamble <sagar.a.kamble@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Akash Goel [Tue, 25 Mar 2014 12:31:50 +0000 (18:01 +0530)]
drm/i915: Remove the enabling of VS_TIMER_DISPATCH bit in MI MODE reg
This patch Removes the VS_TIMER_DISPATCH bit enable in MI MODE reg for
platforms > Gen6.
VS_TIMER_DISPATCH bit enable was earlier required as a part of
WA 'WaTimedSingleVertexDispatch', which is now applicable only to
platforms < Gen7.
v2: Enhancing the scope of the patch to full Gen7 (Chris)
v3: Modifying the WA condition to the cover the applicable platforms,
and adding the WA name in comments. (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com> Signed-off-by: Sourab Gupta <sourab.gupta@intel.com> Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # ivb, hsw -Chris Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Deepak S [Sat, 15 Mar 2014 14:53:22 +0000 (20:23 +0530)]
drm/i915: Track the enabled PM interrupts in dev_priv.
When we use different rps events for different platforms or due to wa,
we might end up needing this logic in a lot of places. Instead of
this let's use a variable in dev_priv to track the enabled PM
interrupts.
v2: Initialize pm_rps_events in intel_irq_init() (Ville).
Signed-off-by: Deepak S <deepak.s@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Frob the commit message a bit since the English was a bit too
garbled ;-) ] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Don't enable display error interrupts from the start
we don't enable underrun interrupts any more at takeover time.
Unfortunately I've forgotten to also adjust the sw-side tracking.
Since the code assumes that disabled pipes have underrun reporting
enabled set the disable flag only on all pipes which are active at
takeover time. Without this underrun reporting wasn't enabled
correctly on the first modeset. Note that for fastboot this is another
piece of state that needs to be fixed up by enabling the underrung
reporting after watermarks have beend fixed up.
On ivb/hsw an additional effect of this regression was that also all
cpu crc reporting stopped working since the master error interrupt it
shared across all pipes and sources.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76150
[danvet: Augment the code comment and polish the commit message a bit,
as discussed with Jani.] Reviewed-by: Jani Nikula <jani.nikula@intel.com> Tested-by: lu hua <huax.lu@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 14 Mar 2014 23:08:55 +0000 (00:08 +0100)]
drm/i915: fix up semaphore_waits_for
There's an entire pile of issues in here:
- Use the main RING_HEAD register, not ACTHD. ACTHD points at the gtt
offset of the batch buffer when a batch is executed. Semaphores are
always emitted to the main ring, so we always want to look at that.
- Mask the obtained HEAD pointer with the actual ring size, which is
much smaller. Together with the above issue this resulted us in
trying to dereference a pointer way outside of the ring mmio
mapping. The resulting invalid access in interrupt context
(hangcheck is executed from timers) lead to a full blown kernel
panic. The fbcon panic handler then tried to frob our driver harder,
resulting in a full machine hang at least on my snb here where I've
stumbled over this.
- Handle ring wrapping correctly and be a bit more explicit about how
many dwords we're scanning. We probably should also scan more than
just 4 ...
- Space out some of teh computations for readability.
This reduces hard-hangs on my snb here. Mika and QA both say that it
doesn't completel remove them, but at least for me it's a clear
improvement in stability.
Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=74100 Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_add_edid_modes started to WARN about the mode_config.mutex not
being held in the lvds and dp initialization code.
Now since this is init code locking is fairly redudant if it wouldn't
be for the drm core registering sysfs files a bit early. And the
locking WARNINGs nicely enforce that indeed all access to the mode
lists are properly protected. And a full audit shows that only i915
and gma500 touch the modes lists at init time.
Hence I've opted to wrap up this entire mode detection sequence for
fixed panels with the mode_config mutex for both lvds and edp outputs.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.
Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.
We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).
So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> CC: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
John Stultz [Thu, 27 Mar 2014 23:30:49 +0000 (16:30 -0700)]
time: Revert to calling clock_was_set_delayed() while in irq context
In commit 47a1b796306356f35 ("tick/timekeeping: Call
update_wall_time outside the jiffies lock"), we moved to calling
clock_was_set() due to the fact that we were no longer holding
the timekeeping or jiffies lock.
However, there is still the problem that clock_was_set()
triggers an IPI, which cannot be done from the timer's hard irq
context, and will generate WARN_ON warnings.
Apparently in my earlier testing, I'm guessing I didn't bump the
dmesg log level, so I somehow missed the WARN_ONs.
Thus we need to revert back to calling clock_was_set_delayed().
Wei Yang [Thu, 27 Mar 2014 01:28:31 +0000 (09:28 +0800)]
net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset
The second parameter of __mlx4_init_one() is used to identify whether the
pci_dev is a PF or VF. Currently, when it is invoked in mlx4_pci_slot_reset()
this information is missed.
This patch match the pci_dev with mlx4_pci_table and passes the
pci_device_id.driver_data to __mlx4_init_one() in mlx4_pci_slot_reset().
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zoltan Kiss [Wed, 26 Mar 2014 22:37:45 +0000 (22:37 +0000)]
core, nfqueue, openvswitch: Orphan frags in skb_zerocopy and handle errors
skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log