Adel Gadllah [Thu, 9 Oct 2014 07:29:29 +0000 (09:29 +0200)]
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Mark Einon [Sun, 19 Oct 2014 19:25:26 +0000 (20:25 +0100)]
MAINTAINERS: Remove duplicate entry for usbip driver
The usbip driver was moved out of staging in 3.17-rc3 but the MAINTAINERS file
still has the old staging entry as well as the new one. Remove the old entry.
Signed-off-by: Mark Einon <mark.einon@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luis Henriques [Wed, 1 Oct 2014 23:10:57 +0000 (00:10 +0100)]
usb: storage: fix build warnings !CONFIG_PM
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: Remove references to non-existent PLAT_S5P symbol
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde96
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.
Hans de Goede [Tue, 28 Oct 2014 10:05:29 +0000 (11:05 +0100)]
xhci: Disable streams on Asmedia 1042 xhci controllers
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Alan Stern [Fri, 31 Oct 2014 18:49:47 +0000 (14:49 -0400)]
usb-storage: handle a skipped data phase
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Tested-by: Paul Osmialowski <newchief@king.net.pl> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Wed, 1 Oct 2014 09:29:14 +0000 (11:29 +0200)]
usb: Do not allow usb_alloc_streams on unconfigured devices
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Paris [Thu, 30 Oct 2014 15:04:47 +0000 (11:04 -0400)]
cdc-acm: ensure that termios get set when the port is activated
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com> Reviewed-by: Johan Hovold <johan@kernel.org> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 2 Nov 2014 22:45:52 +0000 (14:45 -0800)]
Merge tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
Linus Torvalds [Sun, 2 Nov 2014 22:39:35 +0000 (14:39 -0800)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of six patches consisting of:
- two MAINTAINER updates
- two scsi-mq fixs for the old parallel interface (not every request
is tagged and we need to set the right flags to populate the SPI
tag message)
- a fix for a memory leak in scatterlist traversal caused by a
preallocation update in 3.17
- an ipv6 fix for cxgbi"
[ The scatterlist fix also came in separately through the block layer tree ]
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ufs - remove self
MAINTAINERS: change hpsa and cciss maintainer
libcxgbi : support ipv6 address host_param
scsi: set REQ_QUEUE for the blk-mq case
Revert "block: all blk-mq requests are tagged"
lib/scatterlist: fix memory leak with scsi-mq
Linus Torvalds [Sun, 2 Nov 2014 22:27:30 +0000 (14:27 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too astounding or major: radeon, i915, vmwgfx, armada and
exynos.
Biggest ones:
- vmwgfx has one big locking regression fix
- i915 has come displayport fixes
- radeon has some stability and a memory alloc failure
- armada and exynos have some vblank fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/radeon: remove some buggy dead code
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
...
Linus Torvalds [Sun, 2 Nov 2014 20:56:20 +0000 (12:56 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
Linus Torvalds [Sun, 2 Nov 2014 20:31:02 +0000 (12:31 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A small set of x86 fixes. The most serious is an SRCU lockdep fix.
A bit late - needed some time to test the SRCU fix, which only came in
on Friday"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx: defer load of APIC access page address during reset
KVM: nVMX: Disable preemption while reading from shadow VMCS
KVM: x86: Fix far-jump to non-canonical check
KVM: emulator: fix execution close to the segment limit
KVM: emulator: fix error code for __linearize
Dave Airlie [Sun, 2 Nov 2014 19:23:17 +0000 (05:23 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
Linus Torvalds [Sun, 2 Nov 2014 18:28:43 +0000 (10:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"A bunch of assorted fixes, most of them followups to overlayfs merge"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: initialize ->is_cursor
Return short read or 0 at end of a raw device, not EIO
isofs: don't bother with ->d_op for normal case
isofs_cmp(): we'll never see a dentry for . or ..
overlayfs: fix lockdep misannotation
ovl: fix check for cursor
overlayfs: barriers for opening upper-layer directory
rcu: Provide counterpart to rcu_dereference() for non-RCU situations
staging: android: logger: Fix log corruption regression
Linus Torvalds [Sun, 2 Nov 2014 18:20:26 +0000 (10:20 -0800)]
irda: stop calling sk_prot->disconnect() on connection failure
The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer. And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.
So calling that function is doubly wrong, and will just cause an oops.
Reported-by: Martin Lang <mlg.hessigheim@gmail.com> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:56 +0000 (14:31 +0200)]
drm/exynos: correct connector->dpms field before resuming
During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:55 +0000 (14:31 +0200)]
drm/exynos: enable vblank after DPMS on
Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:54 +0000 (14:31 +0200)]
drm/exynos: init kms poll at the end of initialization
HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Jan Kiszka [Wed, 8 Oct 2014 16:05:39 +0000 (18:05 +0200)]
KVM: nVMX: Disable preemption while reading from shadow VMCS
In order to access the shadow VMCS, we need to load it. At this point,
vmx->loaded_vmcs->vmcs and the actually loaded one start to differ. If
we now get preempted by Linux, vmx_vcpu_put and, on return, the
vmx_vcpu_load will work against the wrong vmcs. That can cause
copy_shadow_to_vmcs12 to corrupt the vmcs12 state.
Fix the issue by disabling preemption during the copy operation.
copy_vmcs12_to_shadow is safe from this issue as it is executed by
vmx_vcpu_run when preemption is already disabled before vmentry.
This bug is exposed by running Jailhouse within KVM on CPUs with
shadow VMCS support. Jailhouse never expects an interrupt pending
vmexit, but the bug can cause it if, after copy_shadow_to_vmcs12
is preempted, the active VMCS happens to have the virtual interrupt
pending flag set in the CPU-based execution controls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit [Mon, 27 Oct 2014 22:03:43 +0000 (00:03 +0200)]
KVM: x86: Fix far-jump to non-canonical check
Commit d1442d85cc30 ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc30ea75f7d399474ca738e0bc96f715 Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dave Airlie [Sat, 1 Nov 2014 23:23:31 +0000 (09:23 +1000)]
Merge branch 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux
A critical 3.18 regression fix from Rob, (thanks!)
A fix to avoid advertizing modes we can't support from Sinclair
(welcome Sinclair!)
and a fix for an incorrect hash key computation from me that is
completely harmless, but can wait 'til the next merge window if necessary.
(I can't really bother stable with this one).
* 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
Linus Torvalds [Sat, 1 Nov 2014 22:11:27 +0000 (15:11 -0700)]
Merge tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some staging driver fixes for 3.18-rc3. Mostly iio and
comedi driver fixes for issues reported by people.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: fix memory leak / bad pointer freeing for chanlist
staging: comedi: Kconfig: fix config COMEDI_ADDI_APCI_3120 dependants
staging: comedi: widen subdevice number argument in ioctl handlers
staging: rtl8723au: Fix alignment of mac_addr for ether_addr_copy() usage
drivers/staging/comedi/Kconfig: Let COMEDI_II_PCI20KC depend on HAS_IOMEM
staging: comedi: (regression) channel list must be set for COMEDI_CMD ioctl
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Linus Torvalds [Sat, 1 Nov 2014 22:08:04 +0000 (15:08 -0700)]
Merge tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 3.18-rc3.
Mostly usb-serial device ids and gadget fixes for issues that have
been reported. Full details are in the shortlog.
All of these have been in linux-next for a while"
* tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
usb: chipidea: Fix oops when removing the ci_hdrc module
usb: gadget: function: Fixed the return value on error path
usb: dwc2: gadget: disable phy before turning off power regulators
usb: gadget: function: Remove redundant usb_free_all_descriptors
usb: dwc3: gadget: Properly initialize LINK TRB
usb: dwc2: gadget: fix gadget unregistration in udc_stop() function
usb: dwc2: Bits in bitfield should add up to 32
usb: dwc2: gadget: sparse warning of context imbalance
usb: gadget: udc: core: fix kernel oops with soft-connect
usb: musb: musb_dsps: fix NULL pointer in suspend
usb: musb: dsps: start OTG timer on resume again
usb: gadget: loopback: don't queue requests to bogus endpoints
usb: ffs: fix regression when quirk_ep_out_aligned_size flag is set
usb: gadget: f_fs: remove redundant ffs_data_get()
usb: gadget: udc: USB_GADGET_XILINX should depend on HAS_DMA
Revert "usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete"
usb: gadget: composite: enable BESL support
usb: musb: cppi41: restart hrtimer only if not yet done
usb: dwc3: ep0: fix Data Phase for transfer sizes aligned to wMaxPacketSize
usb: serial: ftdi_sio: add "bricked" FTDI device PID
...
Linus Torvalds [Sat, 1 Nov 2014 17:41:26 +0000 (10:41 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Filipe is nailing down some problems with our skinny extent variation,
and Dave's patch fixes endian problems in the new super block checks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix race that makes btrfs_lookup_extent_info miss skinny extent items
Btrfs: properly clean up btrfs_end_io_wq_cache
Btrfs: fix invalid leaf slot access in btrfs_lookup_extent()
btrfs: use macro accessors in superblock validation checks
Linus Torvalds [Sat, 1 Nov 2014 02:51:11 +0000 (19:51 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
Linus Torvalds [Sat, 1 Nov 2014 02:08:25 +0000 (19:08 -0700)]
Merge tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes received after my previous pull request plus one that
has been in the works for quite a while, but its previous version
caused problems to happen, so it's been deferred till now.
Fixed are two recent regressions (MFD enumeration and cpufreq-dt),
ACPI EC regression introduced in 3.17, system suspend error code path
regression introduced in 3.15, an older bug related to recovery from
failing resume from hibernation and a cpufreq-dt driver issue related
to operation performance points.
Specifics:
- Fix a crash on r8a7791/koelsch during resume from system suspend
caused by a recent cpufreq-dt commit (Geert Uytterhoeven).
- Fix an MFD enumeration problem introduced by a recent commit adding
ACPI support to the MFD subsystem that exposed a weakness in the
ACPI core causing ACPI enumeration to be applied to all devices
associated with one ACPI companion object, although it should be
used for one of them only (Mika Westerberg).
- Fix an ACPI EC regression introduced during the 3.17 cycle causing
some Samsung laptops to misbehave as a result of a workaround
targeted at some Acer machines. That includes a revert of a commit
that went too far and a quirk for the Acer machines in question.
From Lv Zheng.
- Fix a regression in the system suspend error code path introduced
during the 3.15 cycle that causes it to fail to take errors from
asychronous execution of "late" suspend callbacks into account
(Imre Deak).
- Fix a long-standing bug in the hibernation resume error code path
that fails to roll back everything correcty on "freeze" callback
errors and leaves some devices in a "suspended" state causing more
breakage to happen subsequently (Imre Deak).
- Make the cpufreq-dt driver disable operation performance points
that are not supported by the VR connected to the CPU voltage plane
with acceptable tolerance instead of constantly failing voltage
scaling later on (Lucas Stach)"
* tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus)
PM / Sleep: fix recovery during resuming from hibernation
PM / Sleep: fix async suspend_late/freeze_late error handling
ACPI: Use ACPI companion to match only the first physical device
cpufreq: cpufreq-dt: disable unsupported OPPs
An unintentional sysfs filename change in commit 5136b2da770d
("PCI: convert bus code to use dev_groups"), which appeared in
v3.13, changed "enable" to "enabled", and this changes it back.
Old users of "enable" are currently broken and will be helped by
this change. Anything that started to use "enabled" after v3.13
will be broken by this change. If necessary, we can add a symlink
to make both work, but this patch doesn't do that.
A mistaken duplicate merge that added a check twice. Nothing's
broken; this just removes the unnecessary code.
Freescale i.MX6
- Wait for clocks to stabilize after ref_en (Richard Zhu)
An i.MX6 clock problem that prevents mx6 nitrogen boards from booting"
* tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Rename sysfs 'enabled' file back to 'enable'
PCI: imx6: Wait for clocks to stabilize after ref_en
Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe"
Andy Lutomirski [Sat, 1 Nov 2014 01:08:45 +0000 (18:08 -0700)]
x86_64, entry: Fix out of bounds read on sysenter
Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code
reads out of bounds, causing the NT fix to be unreliable. But, and
this is much, much worse, if your stack is somehow just below the
top of the direct map (or a hole), you read out of bounds and crash.
That read is deterministically above the top of the stack. I
thought I even single-stepped through this code when I wrote it to
check the offset, but I clearly screwed it up.
Fixes: 8c7aa698baca ("x86_64, entry: Filter RFLAGS.NT on entry from userspace") Reported-by: Rusty Russell <rusty@ozlabs.org> Cc: stable@vger.kernel.org Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 31 Oct 2014 23:22:29 +0000 (16:22 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"A set of miscellaneous ext4 bug fixes for 3.18"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: make ext4_ext_convert_to_initialized() return proper number of blocks
ext4: bail early when clearing inode journal flag fails
ext4: bail out from make_indexed_dir() on first error
jbd2: use a better hash function for the revoke table
ext4: prevent bugon on race between write/fcntl
ext4: remove extent status procfs files if journal load fails
ext4: disallow changing journal_csum option during remount
ext4: enable journal checksum when metadata checksum feature enabled
ext4: fix oops when loading block bitmap failed
ext4: fix overflow when updating superblock backups after resize
Linus Torvalds [Fri, 31 Oct 2014 23:18:47 +0000 (16:18 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota and ext3 fixes from Jan Kara.
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fs, jbd: use a more generic hash function
quota: Properly return errors from dquot_writeback_dquots()
ext3: Don't check quota format when there are no quota files
Pull networking fixes from David Miller:
"A bit has accumulated, but it's been a week or so since my last batch
of post-merge-window fixes, so...
1) Missing module license in netfilter reject module, from Pablo.
Lots of people ran into this.
2) Off by one in mac80211 baserate calculation, from Karl Beldan.
3) Fix incorrect return value from ax88179_178a driver's set_mac_addr
op, which broke use of it with bonding. From Ian Morgan.
4) Checking of skb_gso_segment()'s return value was not all
encompassing, it can return an SKB pointer, a pointer error, or
NULL. Fix from Florian Westphal.
This is crummy, and longer term will be fixed to just return error
pointers or a real SKB.
6) Encapsulation offloads not being handled by
skb_gso_transport_seglen(). From Florian Westphal.
7) Fix deadlock in TIPC stack, from Ying Xue.
8) Fix performance regression from using rhashtable for netlink
sockets. The problem was the synchronize_net() invoked for every
socket destroy. From Thomas Graf.
9) Fix bug in eBPF verifier, and remove the strong dependency of BPF
on NET. From Alexei Starovoitov.
10) In qdisc_create(), use the correct interface to allocate
->cpu_bstats, otherwise the u64_stats_sync member isn't
initialized properly. From Sabrina Dubroca.
11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter.
12) nf_tables_newchain() was erroneously expecting error pointers from
netdev_alloc_pcpu_stats(). It only returna a valid pointer or
NULL. From Sabrina Dubroca.
13) Fix use-after-free in _decode_session6(), from Li RongQing.
14) When we set the TX flow hash on a socket, we mistakenly do so
before we've nailed down the final source port. Move the setting
deeper to fix this. From Sathya Perla.
15) NAPI budget accounting in amd-xgbe driver was counting descriptors
instead of full packets, fix from Thomas Lendacky.
16) Fix total_data_buflen calculation in hyperv driver, from Haiyang
Zhang.
17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke
Mehrtens.
18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is
that something that ends up being vmalloc memory can't be passed
to the crypto hash routines via scatter-gather lists. From Eric
Dumazet.
19) Fix regression in promiscuous mode enabling in cdc-ether, from
Olivier Blin.
20) Bucket eviction and frag entry killing can race with eachother,
causing an unlink of the object from the wrong list. Fix from
Nikolay Aleksandrov.
21) Missing initialization of spinlock in cxgb4 driver, from Anish
Bhatt.
22) Do not cache ipv4 routing failures, otherwise if the sysctl for
forwarding is subsequently enabled this won't be seen. From
Nicolas Cavallari"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits)
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
drivers: net: cpsw: Fix broken loop condition in switch mode
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
stmmac: pci: set default of the filter bins
net: smc91x: Fix gpios for device tree based booting
mpls: Allow mpls_gso to be built as module
mpls: Fix mpls_gso handler.
r8152: stop submitting intr for -EPROTO
netfilter: nft_reject_bridge: restrict reject to prerouting and input
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing
drivers/net: macvtap and tun depend on INET
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
drivers/net: Disable UFO through virtio
net: skb_fclone_busy() needs to detect orphaned skb
gre: Use inner mac length when computing tunnel length
mlx4: Avoid leaking steering rules on flow creation error flow
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
...
Pull sparc update from David Miller:
"Two changes:
1) It makes no sense to execute a VTOC partition table request in the
Sun virtual block device driver and fail to load if it doesn't
succeed because a) we don't use the result at all and b) it won't
succeed if there is an EFI partition on the disk, for example.
We read the partition table via the normal means in the block layer
anyways, so this is really completely useless, so just remove it.
From Dwight Engen.
2) Hook up new bpf system call"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: don't call VD_OP_GET_VTOC
sparc: Hook up bpf system call.
Linus Torvalds [Fri, 31 Oct 2014 21:43:42 +0000 (14:43 -0700)]
Merge tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze updates from Michal Simek:
- wire-up new bpf syscall
- fix PCI bug
- fix Kconfig warning
* tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire up bpf syscall
microblaze: Fix IO space breakage after of_pci_range_to_resource() change
microblaze: Fix missing NR_CPUS in menuconfig
Linus Torvalds [Fri, 31 Oct 2014 21:30:16 +0000 (14:30 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Fixes from all around the place:
- hyper-V 32-bit PAE guest kernel fix
- two IRQ allocation fixes on certain x86 boards
- intel-mid boot crash fix
- intel-quark quirk
- /proc/interrupts duplicate irq chip name fix
- cma boot crash fix
- syscall audit fix
- boot crash fix with certain TSC configurations (seen on Qemu)
- smpboot.c build warning fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, pageattr: Prevent overflow in slow_virt_to_phys() for X86_PAE
ACPI, irq, x86: Return IRQ instead of GSI in mp_register_gsi()
x86, intel-mid: Create IRQs for APB timers and RTC timers
x86: Don't enable F00F workaround on Intel Quark processors
x86/irq: Fix XT-PIC-XT-PIC in /proc/interrupts
x86, cma: Reserve DMA contiguous area after initmem_init()
i386/audit: stop scribbling on the stack frame
x86, apic: Handle a bad TSC more gracefully
x86: ACPI: Do not translate GSI number if IOAPIC is disabled
x86/smpboot: Move data structure to its primary usage scope
* acpi-scan:
ACPI: Use ACPI companion to match only the first physical device
* acpi-ec:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
Linus Torvalds [Fri, 31 Oct 2014 21:05:35 +0000 (14:05 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Various scheduler fixes all over the place: three SCHED_DL fixes,
three sched/numa fixes, two generic race fixes and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/dl: Fix preemption checks
sched: Update comments for CLONE_NEWNS
sched: stop the unbound recursion in preempt_schedule_context()
sched/fair: Fix division by zero sysctl_numa_balancing_scan_size
sched/fair: Care divide error in update_task_scan_period()
sched/numa: Fix unsafe get_task_struct() in task_numa_assign()
sched/deadline: Fix races between rt_mutex_setprio() and dl_task_timer()
sched/deadline: Don't replenish from a !SCHED_DEADLINE entity
sched: Fix race between task_group and sched_task_group
Linus Torvalds [Fri, 31 Oct 2014 21:01:47 +0000 (14:01 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus on the kernel side:
- a revert for a newly introduced PMU driver which isn't complete yet
and where we ran out of time with fixes (to be tried again in
v3.19) - this makes up for a large chunk of the diffstat.
- compilation warning fixes
- a printk message fix
- event_idx usage fixes/cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Trivial typo fix for --demangle
perf tools: Fix report -F dso_from for data without branch info
perf tools: Fix report -F dso_to for data without branch info
perf tools: Fix report -F symbol_from for data without branch info
perf tools: Fix report -F symbol_to for data without branch info
perf tools: Fix report -F mispredict for data without branch info
perf tools: Fix report -F in_tx for data without branch info
perf tools: Fix report -F abort for data without branch info
perf tools: Make CPUINFO_PROC an array to support different kernel versions
perf callchain: Use global caching provided by libunwind
perf/x86/intel: Revert incomplete and undocumented Broadwell client support
perf/x86: Fix compile warnings for intel_uncore
perf: Fix typos in sample code in the perf_event.h header
perf: Fix and clean up initialization of pmu::event_idx
perf: Fix bogus kernel printk
perf diff: Add missing hists__init() call at tool start
Linus Torvalds [Fri, 31 Oct 2014 20:57:45 +0000 (13:57 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull futex fixes from Ingo Molnar:
"This contains two futex fixes: one fixes a race condition, the other
clarifies shared/private futex comments"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Fix a race condition between REQUEUE_PI and task death
futex: Mention key referencing differences between shared and private futexes
Please pull this small batch of spooky fixes intended for the 3.18
stream...boo!
Cyril Brulebois adds an rt2x00 device ID.
Dan Carpenter provides a one-line masking fix for an ath9k debugfs
entry.
Larry Finger gives us a package of small rtlwifi fixes which add some
bits that were left out of some feature updates that were included
in the merge window. Hopefully this isn't a sign that the rtlwifi
base is getting too big...
Marc Yang brings a fix for a temporary mwifiex stall when doing 11n
RX reordering.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennart Sorensen [Fri, 31 Oct 2014 17:38:52 +0000 (13:38 -0400)]
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Lennart Sorensen [Fri, 31 Oct 2014 17:28:54 +0000 (13:28 -0400)]
drivers: net: cpsw: Fix broken loop condition in switch mode
0d961b3b52f566f823070ce2366511a7f64b928c (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Fri, 31 Oct 2014 03:50:15 +0000 (20:50 -0700)]
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
If a driver supports reading EEPROM but no EEPROM is installed in the system,
the driver's get_eeprom_len function returns 0. ethtool will subsequently
try to read that zero-length EEPROM anyway. If the driver does not support
EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver
does support EEPROM access but no EEPROM is installed, the operation will
return -EINVAL. Return -EOPNOTSUPP in both cases for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Fri, 31 Oct 2014 16:28:03 +0000 (18:28 +0200)]
stmmac: pci: set default of the filter bins
The commit 3b57de958e2a brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e2a (net: stmmac: Support devicetree configs for mcast and ucast filter entries) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Thu, 30 Oct 2014 16:59:27 +0000 (09:59 -0700)]
net: smc91x: Fix gpios for device tree based booting
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dwight Engen [Thu, 30 Oct 2014 19:55:35 +0000 (15:55 -0400)]
sunvdc: don't call VD_OP_GET_VTOC
The VD_OP_GET_VTOC operation will succeed only if the vdisk backend has a
VTOC label, otherwise it will fail. In particular, it will return error
48 (ENOTSUP) if the disk has an EFI label. VTOC disk labels are already
handled by directly reading the disk in block/partitions/sun.c (enabled by
CONFIG_SUN_PARTITION which defaults to y on SPARC). Since port->label is
unused in the driver, remove the call and the field.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Thu, 30 Oct 2014 07:50:04 +0000 (00:50 -0700)]
mpls: Allow mpls_gso to be built as module
Kconfig already allows mpls to be built as module. Following patch
fixes Makefile to do same.
CC: Simon Horman <simon.horman@netronome.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Thu, 30 Oct 2014 07:49:57 +0000 (00:49 -0700)]
mpls: Fix mpls_gso handler.
mpls gso handler needs to pull skb after segmenting skb.
CC: Simon Horman <simon.horman@netronome.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 31 Oct 2014 19:43:52 +0000 (12:43 -0700)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Ingo Molnar:
"The tree contains two RCU fixes and a compiler quirk comment fix"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make rcu_barrier() understand about missing rcuo kthreads
compiler/gcc4+: Remove inaccurate comment about 'asm goto' miscompiles
rcu: More on deadlock between CPU hotplug and expedited grace periods
Linus Torvalds [Fri, 31 Oct 2014 19:33:05 +0000 (12:33 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"As you requested in the rc2 release mail the timer department serves
you a few real bug fixes:
- Fix the probe logic of the architected arm/arm64 timer
- Plug a stack info leak in posix-timers
- Prevent a shift out of bounds issue in the clockevents core"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM/ARM64: arch-timer: fix arch_timer_probed logic
clockevents: Prevent shift out of bounds
posix-timers: Fix stack info leak in timer_create()
Linus Torvalds [Fri, 31 Oct 2014 19:28:38 +0000 (12:28 -0700)]
Merge tag 'trace-fixes-v3.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"ARM has system calls outside the NR_syscalls range, and the generic
tracing system does not support that and without checks, it can cause
an oops to be reported.
Rabin Vincent added checks in the return code on syscall events to
make sure that the system call number is within the range that tracing
knows about, and if not, simply ignores the system call.
The system call tracing infrastructure needs to be rewritten to handle
these cases better, but for now, to keep from oopsing, this patch will
do"
* tag 'trace-fixes-v3.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/syscalls: Ignore numbers outside NR_syscalls' range
Linus Torvalds [Fri, 31 Oct 2014 18:55:40 +0000 (11:55 -0700)]
Merge tag 'docs-for-linus' of git://git.lwn.net/linux-2.6
Pull documentation fixes from Jonathan Corbet:
"So this is my first pull request since I rashly agreed to look after
the documentation subtree. It contains some typo fixes, a few minor
documentation improvements, and, most importantly, fixes for a couple
of build problems in various bits of sample code.
I fully intend to start sending pull requests with signed tags.
However, due to poor planning on my part and the general obnoxiousness
of life, I'm 2000 miles away from my private key which is sitting on a
powered-down machine. This should be fixed before my next request.
Meanwhile git.lwn.net is a machine under my control, the patches are
all trivial, and all have done time in linux-next"
* tag 'docs-for-linus' of git://git.lwn.net/linux-2.6:
Documentation/SubmittingPatches: Reported-by tags and permission
Documentation: remove outdated references to the linux-next wiki
Documentation: Restrict TSC test code to x86
doc: kernel-parameters.txt: Add ide-generic.probe-mask
vdso: don't require 64-bit math in standalone test
Documentation: Add CONFIG_DEBUG_KMEMLEAK_DEFAULT_OFF case
Documentation: Add default kmemleak off case in kernel-parameters.txt
Docs: Document that the sticky bit is understood by hugetlbfs
DocBook: Reduce noise from make cleandocs
Documentation: fix vdso_standalone_test_x86 on 32-bit
Documentation: dt-bindings: Explain order in patch series
Documentation/ABI/testing/sysfs-ibft: fix a typo
hayeswang [Fri, 31 Oct 2014 05:35:57 +0000 (13:35 +0800)]
r8152: stop submitting intr for -EPROTO
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that the assertion about scope of regressions due to
always keeping keyboard controller in legacy mode was proven wrong.
There are laptops, such as Clevo W650SH, that only have internal
touchpad (no external PS/2 ports), that require active multiplexing
mode to switch the touchpad (Elantech) into native mode instead of
basic PS/2 emulation.
Tobias Klauser [Fri, 31 Oct 2014 16:16:19 +0000 (09:16 -0700)]
Input: altera_ps2 - write to correct register when disabling interrupts
In altera_ps2_close, the data register (offset 0) is written instead of
the control register (offset 4), leading to the RX interrupt not being
disabled. Fix this by calling writel() with the offset for the proper
register.
Dmitry Torokhov [Tue, 28 Oct 2014 16:27:58 +0000 (09:27 -0700)]
Input: max77693-haptic - fix potential overflow
Expression haptic->pwm_dev->period * haptic->magnitude is of type
'unsigned int' and may overflow. We need to convert one of the operands
to u64 before multiplying, instead of casting result (potentially
overflown) to u64.
The following patchset contains fixes for netfilter/ipvs. This round of
fixes is larger than usual at this stage, specifically because of the
nf_tables bridge reject fixes that I would like to see in 3.18. The
patches are:
1) Fix a null-pointer dereference that may occur when logging
errors. This problem was introduced by 4a4739d56b0 ("ipvs: Pull
out crosses_local_route_boundary logic") in v3.17-rc5.
2) Update hook mask in nft_reject_bridge so we can also filter out
packets from there. This fixes 36d2af5 ("netfilter: nf_tables: allow
to filter from prerouting and postrouting"), which needs this chunk
to work.
3) Two patches to refactor common code to forge the IPv4 and IPv6
reject packets from the bridge. These are required by the nf_tables
reject bridge fix.
4) Fix nft_reject_bridge by avoiding the use of the IP stack to reject
packets from the bridge. The idea is to forge the reject packets and
inject them to the original port via br_deliver() which is now
exported for that purpose.
5) Restrict nft_reject_bridge to bridge prerouting and input hooks.
the original skbuff may cloned after prerouting when the bridge stack
needs to flood it to several bridge ports, it is too late to reject
the traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nft_reject_bridge: restrict reject to prerouting and input
Restrict the reject expression to the prerouting and input bridge
hooks. If we allow this to be used from forward or any other later
bridge hook, if the frame is flooded to several ports, we'll end up
sending several reject packets, one per cloned packet.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
If the packet is received via the bridge stack, this cannot reject
packets from the IP stack.
This adds functions to build the reject packet and send it from the
bridge stack. Comments and assumptions on this patch:
1) Validate the IPv4 and IPv6 headers before further processing,
given that the packet comes from the bridge stack, we cannot assume
they are clean. Truncated packets are dropped, we follow similar
approach in the existing iptables match/target extensions that need
to inspect layer 4 headers that is not available. This also includes
packets that are directed to multicast and broadcast ethernet
addresses.
2) br_deliver() is exported to inject the reject packet via
bridge localout -> postrouting. So the approach is similar to what
we already do in the iptables reject target. The reject packet is
sent to the bridge port from which we have received the original
packet.
3) The reject packet is forged based on the original packet. The TTL
is set based on sysctl_ip_default_ttl for IPv4 and per-net
ipv6.devconf_all hoplimit for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip6_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_ip6hdr_put(): to build the IPv6 header.
* nf_reject_ip6_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_iphdr_put(): to build the IPv4 header.
* nf_reject_ip_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David Jeffery [Mon, 29 Sep 2014 14:21:10 +0000 (10:21 -0400)]
Return short read or 0 at end of a raw device, not EIO
Author: David Jeffery <djeffery@redhat.com>
Changes to the basic direct I/O code have broken the raw driver when reading
to the end of a raw device. Instead of returning a short read for a read that
extends partially beyond the device's end or 0 when at the end of the device,
these reads now return EIO.
The raw driver needs the same end of device handling as was added for normal
block devices. Using blkdev_read_iter, which has the needed size checks,
prevents the EIO conditions at the end of the device.
Signed-off-by: David Jeffery <djeffery@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Thomas Hellstrom [Fri, 31 Oct 2014 08:54:22 +0000 (09:54 +0100)]
drm/vmwgfx: Fix hash key computation
The hash key computation in vmw_cmdbuf_res_remove incorrectly didn't take
the resource type into account, contrary to all the other related functions.
This becomes important when the cmdbuf resource manager handles more than
one resource type.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com>
drm: Handle legacy per-crtc locking with full acquire ctx
drm_mode_cursor_common() was switched to use drm_modeset_(un)lock_crtc()
which uses full aquire ctx. So dropping/reaquiring the lock via
drm_modeset_(un)lock() directly isn't the right thing to do, as lockdep
kindly points out.
The 'FIXME's about sorting out whether vmwgfx *really* needs to lock-all
for cursor updates still apply.
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Tested-by: Thomas Hellstrom <thellstrom@vmware.com>
Ben Hutchings [Fri, 31 Oct 2014 03:10:31 +0000 (03:10 +0000)]
drivers/net: macvtap and tun depend on INET
These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled. However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: f43798c27684 ("tun: Allow GSO using virtio_net_hdr") Fixes: b9fb9ee07e67 ("macvtap: add GSO/csum offload support") Fixes: 5188cd44c55d ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets") Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Wed, 29 Oct 2014 22:06:58 +0000 (23:06 +0100)]
tracing/syscalls: Ignore numbers outside NR_syscalls' range
ARM has some private syscalls (for example, set_tls(2)) which lie
outside the range of NR_syscalls. If any of these are called while
syscall tracing is being performed, out-of-bounds array access will
occur in the ftrace and perf sys_{enter,exit} handlers.
# trace-cmd record -e syscalls:* true
[ 17.289329] Unable to handle kernel paging request at virtual address aaaaaace
[ 17.289590] pgd = 9e71c000
[ 17.289696] [aaaaaace] *pgd=00000000
[ 17.289985] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 17.290169] Modules linked in:
[ 17.290391] CPU: 0 PID: 704 Comm: true Not tainted 3.18.0-rc2+ #21
[ 17.290585] task: 9f4dab00 ti: 9e710000 task.ti: 9e710000
[ 17.290747] PC is at ftrace_syscall_enter+0x48/0x1f8
[ 17.290866] LR is at syscall_trace_enter+0x124/0x184
Fix this by ignoring out-of-NR_syscalls-bounds syscall numbers.
Commit cd0980fc8add "tracing: Check invalid syscall nr while tracing syscalls"
added the check for less than zero, but it should have also checked
for greater than NR_syscalls.
Link: http://lkml.kernel.org/p/1414620418-29472-1-git-send-email-rabin@rab.in Fixes: cd0980fc8add "tracing: Check invalid syscall nr while tracing syscalls" Cc: stable@vger.kernel.org # 2.6.33+ Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
David S. Miller [Fri, 31 Oct 2014 00:01:27 +0000 (20:01 -0400)]
Merge branch 'ufo-fix'
Ben Hutchings says:
====================
drivers/net,ipv6: Fix IPv6 fragment ID selection for virtio
The virtio net protocol supports UFO but does not provide for passing a
fragment ID for fragmentation of IPv6 packets. We used to generate a
fragment ID wherever such a packet was fragmented, but currently we
always use ID=0!
v2: Add blank lines after declarations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 30 Oct 2014 18:27:17 +0000 (18:27 +0000)]
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway. Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 916e4cf46d02 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data") Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 30 Oct 2014 18:27:12 +0000 (18:27 +0000)]
drivers/net: Disable UFO through virtio
IPv6 does not allow fragmentation by routers, so there is no
fragmentation ID in the fixed header. UFO for IPv6 requires the ID to
be passed separately, but there is no provision for this in the virtio
net protocol.
Until recently our software implementation of UFO/IPv6 generated a new
ID, but this was a bug. Now we will use ID=0 for any UFO/IPv6 packet
passed through a tap, which is even worse.
Unfortunately there is no distinction between UFO/IPv4 and v6
features, so disable UFO on taps and virtio_net completely until we
have a proper solution.
We cannot depend on VM managers respecting the tap feature flags, so
keep accepting UFO packets but log a warning the first time we do
this.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 916e4cf46d02 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data") Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 30 Oct 2014 17:32:34 +0000 (10:32 -0700)]
net: skb_fclone_busy() needs to detect orphaned skb
Some drivers are unable to perform TX completions in a bound time.
They instead call skb_orphan()
Problem is skb_fclone_busy() has to detect this case, otherwise
we block TCP retransmits and can freeze unlucky tcp sessions on
mostly idle hosts.
Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: 1f3279ae0c13 ("tcp: avoid retransmits of TCP packets hanging in host queues") Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 30 Oct 2014 15:40:56 +0000 (08:40 -0700)]
gre: Use inner mac length when computing tunnel length
Currently, skb_inner_network_header is used but this does not account
for Ethernet header for ETH_P_TEB. Use skb_inner_mac_header which
handles TEB and also should work with IP encapsulation in which case
inner mac and inner network headers are the same.
Tested: Ran TCP_STREAM over GRE, worked as expected.
Signed-off-by: Tom Herbert <therbert@google.com> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The 1st patch fixes a bug in the TX path that supports offloading the
TX checksum of (VXLAN) encapsulated TCP packets. It turns out that the
bug is revealed only when the receiver runs in non-offloaded mode, so
we somehow missed it so far... please queue it for -stable >= 3.14
The 2nd patch makes sure not to leak steering entry on error flow,
please queue it to 3.17-stable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 30 Oct 2014 13:59:28 +0000 (15:59 +0200)]
mlx4: Avoid leaking steering rules on flow creation error flow
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.
One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a9060d "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".
While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 30 Oct 2014 13:59:27 +0000 (15:59 +0200)]
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.
The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.
Fixes: 837052d0ccc5 ('net/mlx4_en: Add netdev support for TCP/IP
offloads of vxlan tunneling') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 30 Oct 2014 23:46:33 +0000 (19:46 -0400)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-10-30
This series contains updates to e1000, igb and ixgbe.
Francesco Ruggeri fixes an issue with e1000 where in a VM the driver did
not support unicast filtering.
Roman Gushchin fixes an issue with igb where the driver was re-using
mapped pages so that packets were still getting dropped even if all
the memory issues are gone and there is free memory.
Junwei Zhang found where in the ixgbe_clean_rx_ring() we were repeating
the assignment of NULL to the receive buffer skb and fixes it.
Emil fixes a race condition between setup_link and SFP detection routine
in the watchdog when setting the advertised speed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: Do not cache routing failures due to disabled forwarding.
If we cache them, the kernel will reuse them, independently of
whether forwarding is enabled or not. Which means that if forwarding is
disabled on the input interface where the first routing request comes
from, then that unreachable result will be cached and reused for
other interfaces, even if forwarding is enabled on them. The opposite
is also true.
This can be verified with two interfaces A and B and an output interface
C, where B has forwarding enabled, but not A and trying
ip route get $dst iif A from $src && ip route get $dst iif B from $src
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr> Reviewed-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Rannaud [Thu, 30 Oct 2014 08:51:01 +0000 (01:51 -0700)]
fs: allow open(dir, O_TMPFILE|..., 0) with mode 0
The man page for open(2) indicates that when O_CREAT is specified, the
'mode' argument applies only to future accesses to the file:
Note that this mode applies only to future accesses of the newly
created file; the open() call that creates a read-only file
may well return a read/write file descriptor.
The man page for open(2) implies that 'mode' is treated identically by
O_CREAT and O_TMPFILE.
But for O_TMPFILE, do_tmpfile() passes the full op->acc_mode to
may_open().
This patch lines up the behavior of O_TMPFILE with O_CREAT. After the
inode is created, may_open() is called with acc_mode = MAY_OPEN, in
do_tmpfile().
A different, but related glibc bug revealed the discrepancy:
https://sourceware.org/bugzilla/show_bug.cgi?id=17523
The glibc lazily loads the 'mode' argument of open() and openat() using
va_arg() only if O_CREAT is present in 'flags' (to support both the 2
argument and the 3 argument forms of open; same idea for openat()).
However, the glibc ignores the 'mode' argument if O_TMPFILE is in
'flags'.
On x86_64, for open(), it magically works anyway, as 'mode' is in
RDX when entering open(), and is still in RDX on SYSCALL, which is where
the kernel looks for the 3rd argument of a syscall.
But openat() is not quite so lucky: 'mode' is in RCX when entering the
glibc wrapper for openat(), while the kernel looks for the 4th argument
of a syscall in R10. Indeed, the syscall calling convention differs from
the regular calling convention in this respect on x86_64. So the kernel
sees mode = 0 when trying to use glibc openat() with O_TMPFILE, and
fails with EACCES.
Signed-off-by: Eric Rannaud <e@nanocritical.com> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie [Thu, 30 Oct 2014 20:54:51 +0000 (06:54 +1000)]
Merge branch 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
- dpm stability fixes for SI and KV
- remove an invalid pci id
- kmalloc_array fixes
- minor cleanups
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: remove some buggy dead code
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
Dave Airlie [Thu, 30 Oct 2014 20:54:10 +0000 (06:54 +1000)]
Merge tag 'drm-intel-fixes-2014-10-30' of git://anongit.freedesktop.org/drm-intel into drm-fixes
bunch of DP fixes, and some backlight fix.
* tag 'drm-intel-fixes-2014-10-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
drm/i915: Do a dummy DPCD read before the actual read
hayeswang [Wed, 29 Oct 2014 03:12:16 +0000 (11:12 +0800)]
r8152: reset tp->speed before autoresuming in open function
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log