The code is currently always checking the first resource of every
device only (several times.) This has been broken since the ACPI check
was added in February 2010 in commit 91fedede0338eb6203cdd618d8ece873fdb7c22c.
Fix the check to run on each resource individually, once.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one error code to return for a bad user-space buffer
pointer passed to a system call in the same address space as the
system call is executed, and that is EFAULT. Furthermore, the
low-level access routines, which catch most of the faults, return
EFAULT already.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Roland McGrath <roland@hack.frob.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regset common infrastructure assumed that regsets would always
have .get and .set methods, but not necessarily .active methods.
Unfortunately people have since written regsets without .set methods.
Rather than putting in stub functions everywhere, handle regsets with
null .get or .set methods explicitly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Roland McGrath <roland@hack.frob.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some codecs don't supply the mute amp-capabilities although the lowest
volume gives the mute. It'd be handy if the parser provides the mute
mixers in such a case.
This patch adds an extension amp-cap bit (which is used only in the
driver) to represent the min volume = mute state. Also modified the
amp cache code to support the fake mute feature when this bit is set
but the real mute bit is unset.
In addition, conexant cx5051 parser uses this new feature to implement
the missing mute controls.
Enable the compat keyctl wrapper on s390x so that 32-bit s390 userspace can
call the keyctl() syscall.
There's an s390x assembly wrapper that truncates all the register values to
32-bits and this then calls compat_sys_keyctl() - but the latter only exists if
CONFIG_KEYS_COMPAT is enabled, and the s390 Kconfig doesn't enable it.
Without this patch, 32-bit calls to the keyctl() syscall are given an ENOSYS
error:
[root@devel4 ~]# keyctl show
Session Keyring
-3: key inaccessible (Function not implemented)
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: dan@danny.cz Cc: Carsten Otte <cotte@de.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: linux-s390@vger.kernel.org Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware generates an interrupt for every completed command in the
queue while the code assumed that it will only generate one interrupt
when the queue is empty. So, explicitly check if the queue is really
empty. This patch fixed problems which occurred due to high traffic on
the bus. While we are here, move the completion-initialization after the
parameter error checking.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. address has to be page aligned.
2. set_memory_x uses page size argument, not size.
Bug causes with following commit:
commit da28179b4e90dda56912ee825c7eaa62fc103797
Author: Mingarelli, Thomas <Thomas.Mingarelli@hp.com>
Date: Mon Nov 7 10:59:00 2011 +0100
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
The GPI_28 IRQ was not registered properly. The registration of
IRQ_LPC32XX_GPI_28 was added and the (wrong) IRQ_LPC32XX_GPI_11 at
LPC32XX_SIC1_IRQ(4) was replaced by IRQ_LPC32XX_GPI_28 (see manual of
LPC32xx / interrupt controller).
Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the initialization of the interrupt controller of the LPC32xx
by correctly setting up SIC1 and SIC2 instead of (wrongly) using the same value
as for the Main Interrupt Controller (MIC).
Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The autofs compat handling fix caused a compile failure when
CONFIG_COMPAT isn't defined.
Instead of adding random #ifdef'fery in autofs, let's just make the
compat helpers earlier to use: without CONFIG_COMPAT, is_compat_task()
just hardcodes to zero.
We could probably do something similar for a number of other cases where
we have #ifdef's in code, but this is the low-hanging fruit.
Reported-and-tested-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the autofs protocol version 5 packet type was added in commit 5c0a32fc2cd0 ("autofs4: add new packet type for v5 communications"), it
obvously tried quite hard to be word-size agnostic, and uses explicitly
sized fields that are all correctly aligned.
However, with the final "char name[NAME_MAX+1]" array at the end, the
actual size of the structure ends up being not very well defined:
because the struct isn't marked 'packed', doing a "sizeof()" on it will
align the size of the struct up to the biggest alignment of the members
it has.
And despite all the members being the same, the alignment of them is
different: a "__u64" has 4-byte alignment on x86-32, but native 8-byte
alignment on x86-64. And while 'NAME_MAX+1' ends up being a nice round
number (256), the name[] array starts out a 4-byte aligned.
End result: the "packed" size of the structure is 300 bytes: 4-byte, but
not 8-byte aligned.
As a result, despite all the fields being in the same place on all
architectures, sizeof() will round up that size to 304 bytes on
architectures that have 8-byte alignment for u64.
Note that this is *not* a problem for 32-bit compat mode on POWER, since
there __u64 is 8-byte aligned even in 32-bit mode. But on x86, 32-bit
and 64-bit alignment is different for 64-bit entities, and as a result
the structure that has exactly the same layout has different sizes.
So on x86-64, but no other architecture, we will just subtract 4 from
the size of the structure when running in a compat task. That way we
will write the properly sized packet that user mode expects.
Not pretty. Sadly, this very subtle, and unnecessary, size difference
has been encoded in user space that wants to read packets of *exactly*
the right size, and will refuse to touch anything else.
Reported-and-tested-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"nframes" comes from the user and "nframes * CD_FRAMESIZE_RAW" can wrap
on 32 bit systems. That would have been ok if we used the same wrapped
value for the copy, but we use a shifted value. We should just use the
checked version of copy_to_user() because it's not going to make a
difference to the speed.
The current epoll code can be tickled to run basically indefinitely in
both loop detection path check (on ep_insert()), and in the wakeup paths.
The programs that tickle this behavior set up deeply linked networks of
epoll file descriptors that cause the epoll algorithms to traverse them
indefinitely. A couple of these sample programs have been previously
posted in this thread: https://lkml.org/lkml/2011/2/25/297.
To fix the loop detection path check algorithms, I simply keep track of
the epoll nodes that have been already visited. Thus, the loop detection
becomes proportional to the number of epoll file descriptor and links.
This dramatically decreases the run-time of the loop check algorithm. In
one diabolical case I tried it reduced the run-time from 15 mintues (all
in kernel time) to .3 seconds.
Fixing the wakeup paths could be done at wakeup time in a similar manner
by keeping track of nodes that have already been visited, but the
complexity is harder, since there can be multiple wakeups on different
cpus...Thus, I've opted to limit the number of possible wakeup paths when
the paths are created.
This is accomplished, by noting that the end file descriptor points that
are found during the loop detection pass (from the newly added link), are
actually the sources for wakeup events. I keep a list of these file
descriptors and limit the number and length of these paths that emanate
from these 'source file descriptors'. In the current implemetation I
allow 1000 paths of length 1, 500 of length 2, 100 of length 3, 50 of
length 4 and 10 of length 5. Note that it is sufficient to check the
'source file descriptors' reachable from the newly added link, since no
other 'source file descriptors' will have newly added links. This allows
us to check only the wakeup paths that may have gotten too long, and not
re-check all possible wakeup paths on the system.
In terms of the path limit selection, I think its first worth noting that
the most common case for epoll, is probably the model where you have 1
epoll file descriptor that is monitoring n number of 'source file
descriptors'. In this case, each 'source file descriptor' has a 1 path of
length 1. Thus, I believe that the limits I'm proposing are quite
reasonable and in fact may be too generous. Thus, I'm hoping that the
proposed limits will not prevent any workloads that currently work to
fail.
In terms of locking, I have extended the use of the 'epmutex' to all
epoll_ctl add and remove operations. Currently its only used in a subset
of the add paths. I need to hold the epmutex, so that we can correctly
traverse a coherent graph, to check the number of paths. I believe that
this additional locking is probably ok, since its in the setup/teardown
paths, and doesn't affect the running paths, but it certainly is going to
add some extra overhead. Also, worth noting is that the epmuex was
recently added to the ep_ctl add operations in the initial path loop
detection code using the argument that it was not on a critical path.
Another thing to note here, is the length of epoll chains that is allowed.
Currently, eventpoll.c defines:
/* Maximum number of nesting allowed inside epoll sets */
#define EP_MAX_NESTS 4
This basically means that I am limited to a graph depth of 5 (EP_MAX_NESTS
+ 1). However, this limit is currently only enforced during the loop
check detection code, and only when the epoll file descriptors are added
in a certain order. Thus, this limit is currently easily bypassed. The
newly added check for wakeup paths, stricly limits the wakeup paths to a
length of 5, regardless of the order in which ep's are linked together.
Thus, a side-effect of the new code is a more consistent enforcement of
the graph depth.
Thus far, I've tested this, using the sample programs previously
mentioned, which now either return quickly or return -EINVAL. I've also
testing using the piptest.c epoll tester, which showed no difference in
performance. I've also created a number of different epoll networks and
tested that they behave as expectded.
I believe this solves the original diabolical test cases, while still
preserving the sane epoll nesting.
Signed-off-by: Jason Baron <jbaron@redhat.com> Cc: Nelson Elhage <nelhage@ksplice.com> Cc: Davide Libenzi <davidel@xmailserver.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
signalfd_cleanup() ensures that ->signalfd_wqh is not used, but
this is not enough. eppoll_entry->whead still points to the memory
we are going to free, ep_unregister_pollwait()->remove_wait_queue()
is obviously unsafe.
Change ep_poll_callback(POLLFREE) to set eppoll_entry->whead = NULL,
change ep_unregister_pollwait() to check pwq->whead != NULL under
rcu_read_lock() before remove_wait_queue(). We add the new helper,
ep_remove_wait_queue(), for this.
This works because sighand_cachep is SLAB_DESTROY_BY_RCU and because
->signalfd_wqh is initialized in sighand_ctor(), not in copy_sighand.
ep_unregister_pollwait()->remove_wait_queue() can play with already
freed and potentially reused ->sighand, but this is fine. This memory
must have the valid ->signalfd_wqh until rcu_read_unlock().
This patch is intentionally incomplete to simplify the review.
It ignores ep_unregister_pollwait() which plays with the same wqh.
See the next change.
epoll assumes that the EPOLL_CTL_ADD'ed file controls everything
f_op->poll() needs. In particular it assumes that the wait queue
can't go away until eventpoll_release(). This is not true in case
of signalfd, the task which does EPOLL_CTL_ADD uses its ->sighand
which is not connected to the file.
This patch adds the special event, POLLFREE, currently only for
epoll. It expects that init_poll_funcptr()'ed hook should do the
necessary cleanup. Perhaps it should be defined as EPOLLFREE in
eventpoll.
__cleanup_sighand() is changed to do wake_up_poll(POLLFREE) if
->signalfd_wqh is not empty, we add the new signalfd_cleanup()
helper.
ep_poll_callback(POLLFREE) simply does list_del_init(task_list).
This make this poll entry inconsistent, but we don't care. If you
share epoll fd which contains our sigfd with another process you
should blame yourself. signalfd is "really special". I simply do
not know how we can define the "right" semantics if it used with
epoll.
The main problem is, epoll calls signalfd_poll() once to establish
the connection with the wait queue, after that signalfd_poll(NULL)
returns the different/inconsistent results depending on who does
EPOLL_CTL_MOD/signalfd_read/etc. IOW: apart from sigmask, signalfd
has nothing to do with the file, it works with the current thread.
In short: this patch is the hack which tries to fix the symptoms.
It also assumes that nobody can take tasklist_lock under epoll
locks, this seems to be true.
Note:
- we do not have wake_up_all_poll() but wake_up_poll()
is fine, poll/epoll doesn't use WQ_FLAG_EXCLUSIVE.
- signalfd_cleanup() uses POLLHUP along with POLLFREE,
we need a couple of simple changes in eventpoll.c to
make sure it can't be "lost".
By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed. In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the F875387 chip, and then setting
the maximum duty cycle. Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
The current use of /tmp for file lists is insecure. Put them under
$objtree/debian instead.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Acked-by: maximilian attems <max@stro.at> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Said commit adds a check whether the carrier link is ok. If the link is
not ok, the skb is freed and no new dma descriptor added to the rx dma
channel. This causes trouble during initialization when the carrier
status has not yet been updated. If a lot of packets are received while
netif_carrier_ok returns false, all dma descriptors are freed and the
rx dma transfer is stopped.
The bug occurs when the board is connected to a network with lots of
traffic and the ifconfig down/up is done, e.g., when reconfiguring
the interface with DHCP.
The bug can be reproduced by flood pinging the davinci board while doing
ifconfig eth0 down
ifconfig eth0 up
on the board.
After that, the rx path stops working and the overrun value reported
by ifconfig is counting up.
Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
Reported-by: Federico Quagliata <federico@quagliata.org> Fixed-by: Federico Quagliata <federico@quagliata.org> Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f11017ec2d1859c661f4e2b12c4a8d250e1f47cf (2.6.37)
moved the fwmark variable in subcontext that is invalidated before
reaching the ip_vs_ct_in_get call. As vaddr is provided as pointer
in the param structure make sure the fwmark variable is in
same context. As the fwmark templates can not be matched,
more and more template connections are created and the
controlled connections can not go to single real server.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.
LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async(). Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended. As one might expect, the outcome is not ideal.
This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them. Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.
For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished. It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that. Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.
For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished. The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.
To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().
An interrupt might be pending when irq_startup() is called, but the
startup code does not invoke the resend logic. In some cases this
prevents the device from issuing another interrupt which renders the
device non functional.
Call the resend function in irq_startup() to keep things going.
Reported-and-tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the primary handler of an interrupt which is marked IRQ_ONESHOT
returns IRQ_HANDLED or IRQ_NONE, then the interrupt thread is not
woken and the unmask logic of the interrupt line is never
invoked. This keeps the interrupt masked forever.
This was not noticed as most IRQ_ONESHOT users wake the thread
unconditionally (usually because they cannot access the underlying
device from hard interrupt context). Though this behaviour was nowhere
documented and not necessarily intentional. Some drivers can avoid the
thread wakeup in certain cases and run into the situation where the
interrupt line s kept masked.
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For L1 instruction cache and L2 cache the shared CPU information
is wrong. On current AMD family 15h CPUs those caches are shared
between both cores of a compute unit.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=42607
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Petkov Borislav <Borislav.Petkov@amd.com> Cc: Dave Jones <davej@redhat.com> Link: http://lkml.kernel.org/r/20120208195229.GA17523@alberich.amd.com Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
[Maintainer note: This patch is a backport of commit 68d07f64b8a11a852d48d1b05b724c3e20c0d94b "USB: Don't fail USB3 probe on
missing legacy PCI IRQ." to the 3.0 kernel. Note, the original patch
description was wrong. We should not back port this to kernels older
than 2.6.36, since that was the first kernel to support MSI and MSI-X
for xHCI hosts. These systems will just not work without MSI support,
so the probe should fail on kernels older than 2.6.36.]
Signed-off-by: Alex Shi <alex.shi@intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1521b) fixes the interaction between usb-storage's
scanning thread and the freezer. The current implementation has a
race: If the device is unplugged shortly after being plugged in and
just as a system sleep begins, the scanning thread may get frozen
before the khubd task. Khubd won't be able to freeze until the
disconnect processing is complete, and the disconnect processing can't
proceed until the scanning thread finishes, so the sleep transition
will fail.
The implementation in the 3.2 kernel suffers from an additional
problem. There the scanning thread calls set_freezable_with_signal(),
and the signals sent by the freezer will mess up the thread's I/O
delays, which are all interruptible.
The solution to both problems is the same: Replace the kernel thread
used for scanning with a delayed-work routine on the system freezable
work queue. Freezable work queues have the nice property that you can
cancel a work item even while the work queue is frozen, and no signals
are needed.
The 3.2 version of this patch solves the problem in Bugzilla #42730.
After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit b3b0870ef3ff ("i387:
do not preload FPU state at task switch time").
However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably
- properly abstracted as a true FPU state switch, rather than as
open-coded save and restore with various hacks.
In particular, implementing it as a proper FPU state switch allows us
to optimize the CR0.TS flag accesses: there is no reason to set the
TS bit only to then almost immediately clear it again. CR0 accesses
are quite slow and expensive, don't flip the bit back and forth for
no good reason.
- Make sure that the same model works for both x86-32 and x86-64, so
that there are no gratuitous differences between the two due to the
way they save and restore segment state differently due to
architectural differences that really don't matter to the FPU state.
- Avoid exposing the "preload" state to the context switch routines,
and in particular allow the concept of lazy state restore: if nothing
else has used the FPU in the meantime, and the process is still on
the same CPU, we can avoid restoring state from memory entirely, just
re-expose the state that is still in the FPU unit.
That optimized lazy restore isn't actually implemented here, but the
infrastructure is set up for it. Of course, older CPU's that use
'fnsave' to save the state cannot take advantage of this, since the
state saving also trashes the state.
In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage. Hopefully it's easier to
follow as a result.
This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.
This fixes two independent bugs at the same time:
- changing 'thread_info->status' from the scheduler causes nasty
problems for the other users of that variable, since it is defined to
be thread-synchronous (that's what the "TS_" part of the naming was
supposed to indicate).
So perfectly valid code could (and did) do
ti->status |= TS_RESTORE_SIGMASK;
and the compiler was free to do that as separate load, or and store
instructions. Which can cause problems with preemption, since a task
switch could happen in between, and change the TS_USEDFPU bit. The
change to TS_USEDFPU would be overwritten by the final store.
In practice, this seldom happened, though, because the 'status' field
was seldom used more than once, so gcc would generally tend to
generate code that used a read-modify-write instruction and thus
happened to avoid this problem - RMW instructions are naturally low
fat and preemption-safe.
- On x86-32, the current_thread_info() pointer would, during interrupts
and softirqs, point to a *copy* of the real thread_info, because
x86-32 uses %esp to calculate the thread_info address, and thus the
separate irq (and softirq) stacks would cause these kinds of odd
thread_info copy aliases.
This is normally not a problem, since interrupts aren't supposed to
look at thread information anyway (what thread is running at
interrupt time really isn't very well-defined), but it confused the
heck out of irq_fpu_usable() and the code that tried to squirrel
away the FPU state.
(It also caused untold confusion for us poor kernel developers).
It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling). And the FPU data that we are going to save/restore is
found there too.
Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.
Cc: Arjan van de Ven <arjan@linux.intel.com> Reported-and-tested-by: Raphael Prevost <raphael@buro.asia> Acked-and-tested-by: Suresh Siddha <suresh.b.siddha@intel.com> Tested-by: Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending. In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state. That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.
We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it
(a) corrupts what is potentially perfectly good FPU state that we might
want to lazy avoid restoring later and
(b) on x86-64 it resulted in a very annoying ordering constraint, where
"__unlazy_fpu()" in the task switch needs to be delayed until after
the DS segment has been reloaded just to get the new DS value.
Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used). It's
simply a much more natural place for the leaked state cleanup.
Yes, taking the trap to re-load the FPU/MMX state is expensive, but so
is spending several days looking for a bug in the state save/restore
code. And the preload code has some rather subtle interactions with
both paravirtualization support and segment state restore, so it's not
nearly as simple as it should be.
Also, now that we no longer necessarily depend on a single bit (ie
TS_USEDFPU) for keeping track of the state of the FPU, we migth be able
to do better. If we are really switching between two processes that
keep touching the FP state, save/restore is inevitable, but in the case
of having one process that does most of the FPU usage, we may actually
be able to do much better than the preloading.
In particular, we may be able to keep track of which CPU the process ran
on last, and also per CPU keep track of which process' FP state that CPU
has. For modern CPU's that don't destroy the FPU contents on save time,
that would allow us to do a lazy restore by just re-enabling the
existing FPU state - with no restore cost at all!
This creates three helper functions that do the TS_USEDFPU accesses, and
makes everybody that used to do it by hand use those helpers instead.
In addition, there's a couple of helper functions for the "change both
CR0.TS and TS_USEDFPU at the same time" case, and the places that do
that together have been changed to use those. That means that we have
fewer random places that open-code this situation.
The intent is partly to clarify the code without actually changing any
semantics yet (since we clearly still have some hard to reproduce bug in
this area), but also to make it much easier to use another approach
entirely to caching the CR0.TS bit for software accesses.
Right now we use a bit in the thread-info 'status' variable (this patch
does not change that), but we might want to make it a full field of its
own or even make it a per-cpu variable.
Touching TS_USEDFPU without touching CR0.TS is confusing, so don't do
it. By moving it into the callers, we always do the TS_USEDFPU next to
the CR0.TS accesses in the source code, and it's much easier to see how
the two go hand in hand.
Commit 5b1cbac37798 ("i387: make irq_fpu_usable() tests more robust")
added a sanity check to the #NM handler to verify that we never cause
the "Device Not Available" exception in kernel mode.
However, that check actually pinpointed a (fundamental) race where we do
cause that exception as part of the signal stack FPU state save/restore
code.
Because we use the floating point instructions themselves to save and
restore state directly from user mode, we cannot do that atomically with
testing the TS_USEDFPU bit: the user mode access itself may cause a page
fault, which causes a task switch, which saves and restores the FP/MMX
state from the kernel buffers.
This kind of "recursive" FP state save is fine per se, but it means that
when the signal stack save/restore gets restarted, it will now take the
'#NM' exception we originally tried to avoid. With preemption this can
happen even without the page fault - but because of the user access, we
cannot just disable preemption around the save/restore instruction.
There are various ways to solve this, including using the
"enable/disable_page_fault()" helpers to not allow page faults at all
during the sequence, and fall back to copying things by hand without the
use of the native FP state save/restore instructions.
However, the simplest thing to do is to just allow the #NM from kernel
space, but fix the race in setting and clearing CR0.TS that this all
exposed: the TS bit changes and the TS_USEDFPU bit absolutely have to be
atomic wrt scheduling, so while the actual state save/restore can be
interrupted and restarted, the act of actually clearing/setting CR0.TS
and the TS_USEDFPU bit together must not.
Instead of just adding random "preempt_disable/enable()" calls to what
is already excessively ugly code, this introduces some helper functions
that mostly mirror the "kernel_fpu_begin/end()" functionality, just for
the user state instead.
Those helper functions should probably eventually replace the other
ad-hoc CR0.TS and TS_USEDFPU tests too, but I'll need to think about it
some more: the task switching functionality in particular needs to
expose the difference between the 'prev' and 'next' threads, while the
new helper functions intentionally were written to only work with
'current'.
The check for save_init_fpu() (introduced in commit 5b1cbac37798: "i387:
make irq_fpu_usable() tests more robust") was the wrong way around, but
I hadn't noticed, because my "tests" were bogus: the FPU exceptions are
disabled by default, so even doing a divide by zero never actually
triggers this code at all unless you do extra work to enable them.
So if anybody did enable them, they'd get one spurious warning.
Some code - especially the crypto layer - wants to use the x86
FP/MMX/AVX register set in what may be interrupt (typically softirq)
context.
That *can* be ok, but the tests for when it was ok were somewhat
suspect. We cannot touch the thread-specific status bits either, so
we'd better check that we're not going to try to save FP state or
anything like that.
Now, it may be that the TS bit is always cleared *before* we set the
USEDFPU bit (and only set when we had already cleared the USEDFP
before), so the TS bit test may actually have been sufficient, but it
certainly was not obviously so.
So this explicitly verifies that we will not touch the TS_USEDFPU bit,
and adds a few related sanity-checks. Because it seems that somehow
AES-NI is corrupting user FP state. The cause is not clear, and this
patch doesn't fix it, but while debugging it I really wanted the code to
be more obviously correct and robust.
The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Felipe Contreras <felipe.contreras@gmail.com> Suggested-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to set the device removable bits in the USB 2.0 roothub
descriptor was accidentally looking at the USB 3.0 port registers
instead of the USB 2.0 registers. This can cause an oops if there are
more USB 2.0 registers than USB 3.0 registers.
This should be backported to kernels as old as 2.6.39, that contain the
commit 4bbb0ace9a3de8392527e3c87926309d541d3b00 "xhci: Return a USB 3.0
hub descriptor for USB3 roothub."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Oliver Neukum <oneukum@suse.de> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Somehow we ended up with duplicate hub feature #defines in ch11.h.
Tatyana Brokhman first created the USB 3.0 hub feature macros in 2.6.38
with commit 0eadcc09203349b11ca477ec367079b23d32ab91 "usb: USB3.0 ch11
definitions". In 2.6.39, I modified a patch from John Youn that added
similar macros in a different place in the same file, and committed dbe79bbe9dcb22cb3651c46f18943477141ca452 "USB 3.0 Hub Changes".
Some of the #defines used different names for the same values. Others
used exactly the same names with the same values, like these gems:
According to my very geeky husband (who looked it up in the C99 spec),
it is allowed to have object-like macros with duplicate names as long as
the replacement list is exactly the same. However, he recalled that
some compilers will give warnings when they find duplicate macros. It's
probably best to remove the duplicates in the stable tree, so that the
code compiles for everyone.
The macros are now fixed to move the feature requests that are specific
to USB 3.0 hubs into a new section (out of the USB 2.0 hub feature
section), and use the most common macro name.
This patch should be backported to 2.6.39.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Tatyana Brokhman <tlinder@codeaurora.org> Cc: John Youn <johnyoun@synopsys.com> Cc: Jamey Sharp <jamey@minilop.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Remove all old mass-storage ids's pid:
0x0026,0x0053,0x0098,0x0099,0x0149,0x0150,0x0160;
2. As the pid from 0x1401 to 0x1510 which have not surely assigned to
use for serial-port or mass-storage port,so i think it should be
removed now, and will re-add after it have assigned in future;
3. sort the pid to WCDMA and CDMA.
Signed-off-by: Rui li <li.rui27@zte.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f39925dbde77 (ipv4: Cache learned redirect information in
inetpeer.) introduced a regression in ICMP redirect handling.
It assumed ipv4_dst_check() would be called because all possible routes
were attached to the inetpeer we modify in ip_rt_redirect(), but thats
not true.
commit 7cc9150ebe (route: fix ICMP redirect validation) tried to fix
this but solution was not complete. (It fixed only one route)
So we must lookup existing routes (including different TOS values) and
call check_peer_redir() on them.
Reported-by: Ivan Zahariev <famzah@icdsoft.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit f39925dbde7788cfb96419c0f092b086aa325c0f
(ipv4: Cache learned redirect information in inetpeer.)
removed some ICMP packet validations which are required by
RFC 1122, section 3.2.2.2:
...
A Redirect message SHOULD be silently discarded if the new
gateway address it specifies is not on the same connected
(sub-) net through which the Redirect arrived [INTRO:2,
Appendix A], or if the source of the Redirect is not the
current first-hop gateway for the specified destination (see
Section 3.3.1).
Signed-off-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit ensures that lost_cnt_hint is correctly updated in
tcp_shifted_skb() for FACK TCP senders. The lost_cnt_hint adjustment
in tcp_sacktag_one() only applies to non-FACK senders, so FACK senders
need their own adjustment.
This applies the spirit of 1e5289e121372a3494402b1b131b41bfe1cf9b7f -
except now that the sequence range passed into tcp_sacktag_one() is
correct we need only have a special case adjustment for FACK.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the newly-SACKed range to be the range of newly-shifted bytes.
Previously - since 832d11c5cd076abc0aa1eaf7be96c81d1a59ce41 -
tcp_shifted_skb() incorrectly called tcp_sacktag_one() with the start
and end sequence numbers of the skb it passes in set to the range just
beyond the range that is newly-SACKed.
This commit also removes a special-case adjustment to lost_cnt_hint in
tcp_shifted_skb() since the pre-existing adjustment of lost_cnt_hint
in tcp_sacktag_one() now properly handles this things now that the
correct start sequence number is passed in.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit allows callers of tcp_sacktag_one() to pass in sequence
ranges that do not align with skb boundaries, as tcp_shifted_skb()
needs to do in an upcoming fix in this patch series.
In fact, now tcp_sacktag_one() does not need to depend on an input skb
at all, which makes its semantics and dependencies more clear.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Binding RST packet outgoing interface to incoming interface
for tcp v4 when there is no socket associate with it.
when sk is not NULL, using sk->sk_bound_dev_if instead.
(suggested by Eric Dumazet).
This has few benefits:
1. tcp_v6_send_reset already did that.
2. This helps tcp connect with SO_BINDTODEVICE set. When
connection is lost, we still able to sending out RST using
same interface.
3. we are sending reply, it is most likely to be succeed
if iif is used
Signed-off-by: Shawn Lu <shawn.lu@ericsson.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially diagnosed on Ubuntu 11.04 with kernel 2.6.38.
velocity_close is not called during a suspend / resume cycle in this
driver and it has no business playing directly with power states.
Signed-off-by: David Lv <DavidLv@viatech.com.cn> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not now, but it looks you are correct. q->qdisc is NULL until another
additional qdisc is attached (beside tfifo). See 50612537e9ab2969312.
The following patch should work.
From: Hagen Paul Pfeifer <hagen@jauu.net>
netem: catch NULL pointer by updating the real qdisc statistic
Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a698af53f (bond: service netpoll arp queue on master device)
tested IFF_SLAVE flag against dev->priv_flags instead of dev->flags
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: WANG Cong <amwang@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.
Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.
This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Acked-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet found that commit 813b3b5db83
(ipv4: Use caller's on-stack flowi as-is in output
route lookups.) that comes in 3.0 added a regression.
The problem appears to be that resulting flowi4_oif is
used incorrectly as input parameter to some routing lookups.
The result is that when connecting to local port without
listener if the IP address that is used is not on a loopback
interface we incorrectly assign RTN_UNICAST to the output
route because no route is matched by oif=lo. The RST packet
can not be sent immediately by tcp_v4_send_reset because
it expects RTN_LOCAL.
So, change ip_route_connect and ip_route_newports to
update the flowi4 fields that are input parameters because
we do not want unnecessary binding to oif.
To make it clear what are the input parameters that
can be modified during lookup and to show which fields of
floiw4 are reused add a new function to update the flowi4
structure: flowi4_update_output.
Thanks to Yurij M. Plotnikov for providing a bug report including a
program to reproduce the problem.
Thanks to Eric Dumazet for tracking the problem down to
tcp_v4_send_reset and providing initial fix.
Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru> Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can not update iph->daddr in ip_options_rcv_srr(), It is too early.
When some exception ocurred later (eg. in ip_forward() when goto
sr_failed) we need the ip header be identical to the original one as
ICMP need it.
Add a field 'nexthop' in struct ip_options to save nexthop of LSRR
or SSRR option.
Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When opt->srr_is_hit is set skb_rtable(skb) has been updated for
'nexthop' and iph->daddr should always equals to skb_rtable->rt_dst
holds, We need update iph->daddr either.
Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If reg_vif_xmit cannot find a routing entry, be sure to
free the skb before returning the error.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Have to free the skb before returning if we fail
the fib lookup.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean Delvare reported bonding on top of 3c59x adapters was not detecting
network cable removal fast enough.
3c59x indeed uses a 60 seconds timer to check link status if carrier is
on, and 5 seconds if carrier is off.
This patch reduces timer period to 5 seconds if device is a bonding
slave.
Reported-by: Jean Delvare <jdelvare@suse.de> Acked-by: Jean Delvare <jdelvare@suse.de> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VETH_INFO_PEER carries struct ifinfomsg plus optional IFLA
attributes. A minimal size of sizeof(struct ifinfomsg) must be
enforced or we may risk accessing that struct beyond the limits
of the netlink message.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shlomo Pongratz reported GRO L2 header check was suited for Ethernet
only, and failed on IB/ipoib traffic.
He provided a patch faking a zeroed header to let GRO aggregates frames.
Roland Dreier, Herbert Xu, and others suggested we change GRO L2 header
check to be more generic, ie not assuming L2 header is 14 bytes, but
taking into account hard_header_len.
__napi_gro_receive() has special handling for the common case (Ethernet)
to avoid a memcmp() call and use an inline optimized function instead.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Reported-by: Shlomo Pongratz <shlomop@mellanox.com> Cc: Roland Dreier <roland@kernel.org> Cc: Or Gerlitz <ogerlitz@mellanox.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a0417fa3a18a ("net: Make qdisc_skb_cb upper size bound
explicit.") made it possible for a netdev driver to use skb->cb
between its header_ops.create method and its .ndo_start_xmit
method. Use this in ipoib_hard_header() to stash away the LL address
(GID + QPN), instead of the "ipoib_pseudoheader" hack. This allows
IPoIB to stop lying about its hard_header_len, which will let us fix
the L2 check for GRO.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.
This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bootup with lockdep enabled has been broken on v7 since b46c0f74657d
("ARM: 7321/1: cache-v7: Disable preemption when reading CCSIDR").
This is because v7_setup (which is called very early during boot) calls
v7_flush_dcache_all, and the save_and_disable_irqs added by that patch
ends up attempting to call into lockdep C code (trace_hardirqs_off())
when we are in no position to execute it (no stack, MMU off).
Fix this by using a notrace variant of save_and_disable_irqs. The code
already uses the notrace variant of restore_irqs.
Reviewed-by: Nicolas Pitre <nico@linaro.org> Acked-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
armv7's flush_cache_all() flushes caches via set/way. To
determine the cache attributes (line size, number of sets,
etc.) the assembly first writes the CSSELR register to select a
cache level and then reads the CCSIDR register. The CSSELR register
is banked per-cpu and is used to determine which cache level CCSIDR
reads. If the task is migrated between when the CSSELR is written and
the CCSIDR is read the CCSIDR value may be for an unexpected cache
level (for example L1 instead of L2) and incorrect cache flushing
could occur.
Disable interrupts across the write and read so that the correct
cache attributes are read and used for the cache flushing
routine. We disable interrupts instead of disabling preemption
because the critical section is only 3 instructions and we want
to call v7_dcache_flush_all from __v7_setup which doesn't have a
full kernel stack with a struct thread_info.
This fixes a problem we see in scm_call() when flush_cache_all()
is called from preemptible context and sometimes the L2 cache is
not properly flushed out.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 22 Feb 2012 16:02:38 +0000 (17:02 +0100)]
ALSA: hda - Fix redundant jack creations for cx5051
[Note that since the patch isn't applicable (and unnecessary) to
3.3-rc, there is no corresponding upstream fix.]
The cx5051 parser calls snd_hda_input_jack_add() in the init callback
to create and initialize the jack detection instances. Since the init
callback is called at each time when the device gets woken up after
suspend or power-saving mode, the duplicated instances are accumulated
at each call. This ends up with the kernel warnings with the too
large array size.
The fix is simply to move the calls of snd_hda_input_jack_add() into
the parser section instead of the init callback.
The fix is needed only up to 3.2 kernel, since the HD-audio jack layer
was redesigned in the 3.3 kernel.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After passing through a ->setxattr() call, eCryptfs needs to copy the
inode attributes from the lower inode to the eCryptfs inode, as they
may have changed in the lower filesystem's ->setxattr() path.
One example is if an extended attribute containing a POSIX Access
Control List is being set. The new ACL may cause the lower filesystem to
modify the mode of the lower inode and the eCryptfs inode would need to
be updated to reflect the new mode.
BugLink: http://bugs.launchpad.net/bugs/900802 Signed-off-by: Till Kamppeter <till.kamppeter@gmail.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init' after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
Call Trace:
Fixes PCI device detection on IBM xSeries IBM 3850 M2 / x3950 M2
when using ACPI resources (_CRS).
This is default, a manual workaround (without this patch)
would be pci=nocrs boot param.
V2: Add dev_warn if the workaround is hit. This should reveal
how common such setups are (via google) and point to possible
problems if things are still not working as expected.
-> Suggested by Jan Beulich.
perf on POWER stopped working after commit e050e3f0a71b (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.
Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.
With the patch applied I get the expected number of samples:
SAMPLE events: 9948
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An error while creating sysfs attribute files in the driver's probe function
results in an error abort, but already created files are not removed. This patch
fixes the problem.
Initialize PPR register for both channels, and set correct PPR register bits.
Also remove unnecessary variable initializations.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: Merged two patches into one] Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RPM calculation from tachometer value does not depend on PPR.
Also, do not report negative RPM values.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: do not report negative RPM values] Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lock i_mmap_mutex for access to the VMA prio list to prevent concurrent
access. Currently, certain parts of the mmap handling are protected by
the region mutex, but not all.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use standard ror64() instead of hand-written.
There is no standard ror64, so create it.
The difference is shift value being "unsigned int" instead of uint64_t
(for which there is no reason). gcc starts to emit native ROR instructions
which it doesn't do for some reason currently. This should make the code
faster.
Patch survives in-tree crypto test and ping flood with hmac(sha512) on.
Zhihua Che reported a possible memleak in slub allocator on
CONFIG_PREEMPT=y builds.
It is possible current thread migrates right before disabling irqs in
__slab_alloc(). We must check again c->freelist, and perform a normal
allocation instead of scratching c->freelist.
Many thanks to Zhihua Che for spotting this bug, introduced in 2.6.39
V2: Its also possible an IRQ freed one (or several) object(s) and
populated c->freelist, so its not a CONFIG_PREEMPT only problem.
Reported-by: Zhihua Che <zhihua.che@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Christoph Lameter <cl@linux.com> Signed-off-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BugLink: https://bugs.launchpad.net/bugs/930842
The reporter states that audio is inaudible by default without muting
'External Amplifier'. Add a quirk to handle his SSID so that changing
the control is not necessary.
Reported-and-tested-by: Benjamin Carlson <elderbubba0810@gmail.com> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately in reducing W from 80 to 16 we ended up unrolling
the loop twice. As gcc has issues dealing with 64-bit ops on
i386 this means that we end up using even more stack space (>1K).
This patch solves the W reduction by moving LOAD_OP/BLEND_OP
into the loop itself, thus avoiding the need to duplicate it.
While the stack space still isn't great (>0.5K) it is at least
in the same ball park as the amount of stack used for our C sha1
implementation.
Note that this patch basically reverts to the original code so
the diff looks bigger than it really is.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous patch used the modulus operator over a power of 2
unnecessarily which may produce suboptimal binary code. This
patch changes changes them to binary ands instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to enable temperature mode aka automatic mode for the F75373 and
F75375 chips, the two FANx_MODE bits in the fan configuration register
need be set to 01, not 10.
projects / karo-tx-linux.git / log