NFC: digital: Add support for NFC DEP Response Waiting Time
When sending an ATR_REQ, the initiator must wait for the ATR_RES at
least 'RWT(nfcdep,activation) + dRWT(nfcdep)' and no more than
'RWT(nfcdep,activation) + dRWT(nfcdep) + dT(nfcdep,initiator)'. This
gives a timeout value between 1237 ms and 1337 ms. This patch defines
DIGITAL_ATR_RES_RWT to 1337 used for the timeout value of ATR_REQ
command.
For other DEP PDUs, the initiator must wait between 'RWT + dRWT(nfcdep)'
and 'RWT + dRWT(nfcdep) + dT(nfcdep,initiator)' where RWT is given by
the following formula: '(256 * 16 / f(c)) * 2^wt' where wt is the value
of the TO field in the ATR_RES response and is in the range between 0
and 14. This patch declares a mapping table for wt values and gives RWT
max values between 100 ms and 5049 ms.
This patch also defines DIGITAL_ATR_RES_TO_WT, the maximum wt value in
target mode, to 8.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch frees the RTOX resp sk_buff in initiator mode. It also makes
use of the free_resp exit point for ATN supervisor PDUs in both
initiator and target mode.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the target receives a NACK PDU, it re-sends the last sent PDU.
ACK PDUs are received by the target as a reply from the initiator to
chained I-PDUs. There are 3 cases to handle:
- If the target has previously received 1 or more ATN PDUs and the PNI
in the ACK PDU is equal to the target PNI - 1, then it means that the
initiator did not received the last issued PDU from the target. In
this case it re-sends this PDU.
- If the target has received 1 or more ATN PDUs but the ACK PNI is not
the target PNI - 1, then this means that this ACK is the reply of the
previous chained I-PDU sent by the target. The target did not received
it on the first attempt and it is being re-sent by the initiator. The
process continues as usual.
- No ATN PDU received before this ACK PDU. This is the reply of a
chained I-PDU. The target keeps on processing its chained I-PDU.
The code has been refactored to avoid too many indentation levels.
Also, ACK and NACK PDUs were not freed. This is now fixed.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: digital: Fix target DEP_REQ I-PDU handling after ATN PDU
When the initiator sends a DEP_REQ I-PDU, the target device may not
reply in a timely manner. In this case the initiator device must send an
attention PDU (ATN) and if the recipient replies with an ATN PDU in
return, then the last I-PDU must be sent again by the initiator.
This patch fixes how the target handles I-PDU received after an ATN PDU
has been received.
There are 2 possible cases:
- The target has received the initial DEP_REQ and sends back the DEP_RES
but the initiator did not receive it. In this case, after the
initiator has sent an ATN PDU and the target replied it (with an ATN
as well), the initiator sends the saved skb of the initial DEP_REQ
again and the target replies with the saved skb of the initial
DEP_RES.
- Or the target did not even received the initial DEP_REQ. In this case,
after the ATN PDUs exchange, the initiator sends the saved skb and the
target simply passes it up, just as usual.
This behavior is controlled using the atn_count and the PNI field of the
digital device structure.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: digital: Remove useless call to skb_reserve()
When allocating chained I-PDUs, there is no need to call skb_reserve()
since it's already done by digital_alloc_skb() and contains enough room
for the driver head and tail data.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: digital: Fix handling of saved PDU sk_buff pointers
This patch fixes the way an I-PDU is saved in case it needs to be sent
again. It is now copied using pskb_copy() and not simply referenced
using skb_get() since it could be modified by the driver.
digital_in_send_saved_skb() and digital_tg_send_saved_skb() still get a
reference on the saved skb which is re-sent but release it if the send
operation fails. That way the caller doesn't have to take care about skb
ref in case of error.
RTOX supervisor PDU must not be saved as this can override a previously
saved I-PDU that should be re-sent later on.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 16 Jun 2016 18:24:45 +0000 (20:24 +0200)]
NFC: digital: Abort last command when dep link goes down
With this patch, the Digital Protocol layer abort the last issued
command when the dep link goes down. That way it does not have to wait
for the driver to reply with a timeout error before sending a new
command (i.e. a start poll command if constant polling is on).
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 16 Jun 2016 18:24:44 +0000 (20:24 +0200)]
NFC: digital: Set the command pending flag
There is a flag in the command structure indicating that this command is
pending. It was checked before sending the command to not send the same
command twice but it was actually never set. This is now fixed.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 16 Jun 2016 18:24:43 +0000 (20:24 +0200)]
NFC: digital: Call pending command callbacks at device unregister
With this patch, when freeing the command queue in the module unregister
function, the callbacks of the commands still queued are called with a
ENODEV error. This gives a chance to the command issuer to free any
memory it could have allocate.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 16 Jun 2016 18:24:42 +0000 (20:24 +0200)]
NFC: digital: Rework error handling in DEP_RES response
The Digital Protocol stack used to send a NACK frame whatever the error
type it receives in digital_in_recv_dep_res(). It actually should only
send a NACK frame on CRC or parity check errors or on any transmission
error if a NACK frame was previously sent. Existing drivers used to send
EIO error for this kind of issues so this patch limits sending of NACK
frames on EIO errors. All other errors will be reported to the upper
layers.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 16 Jun 2016 18:24:41 +0000 (20:24 +0200)]
NFC: digital: Fix a memory leak in NFC-F listening mode
When configured as a target listening for a SENSF_REQ poll command, a
nfcid2 array was allocated for no reason leading to a memory leak. The
nfcid2 is sent by the target in the SENSF_RES reply.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 16 Jun 2016 18:25:23 +0000 (20:25 +0200)]
NFC: port100: Abort current command before switching RF off
If a command is still being processed by the device, the switch RF off
command will be rejected. With this patch, the port100 driver calls
port100_abort_cmd() before sending the switch RF off command.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 16 Jun 2016 18:25:21 +0000 (20:25 +0200)]
NFC: port100: Fix the command cancellation process
The USB out_urb used to send commands to the device can be submitted
through the standard command processing queue coming from the Digital
Protocol layer but it can also be submitted from port100_abort_cmd().
To not submit the URB while already active, a mutex is now used to
protect it and a cmd_cancel flag is used to not send command while
canceling the previous one.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 16 Jun 2016 18:25:20 +0000 (20:25 +0200)]
NFC: port100: Don't send a new command if one is still pending
This patch ensures that a command is not still in process before sending
a new one to the device. This can happen when neard is in constant
polling mode: the configure_hw command can be sent when neard restarts
polling after a LLCP SYMM timeout but before the device has returned in
timeout from the last DEP frame sent.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Wed, 29 Jun 2016 08:48:22 +0000 (10:48 +0200)]
NFC: llcp: Fix usage of llcp_add_tlv()
In functions using llcp_add_tlv(), a skb pointer could be set to NULL
and then reuse afterward.
With this patch, the skb pointer returned by llcp_add_tlv() is ignored
since it can only be the passed skb pointer or NULL when the passed TLV
is NULL. There is also no need to check for the TLV pointer as this is
done by llcp_add_tlv().
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Thu, 23 Jun 2016 09:20:26 +0000 (11:20 +0200)]
NFC: nfcsim: Make use of the Digital layer
With this complete rewrite, the loopback nfcsim driver now relies on the
Digital layer of the nfc stack. As with the previous version, 2 nfc
devices are declared when the driver is initialized. The driver supports
the NFC_DEP protocol in NFC-A and NFC-F technologies.
The 2 devices are using a pair of virtual links for sk_buff exchange.
The out-link of one device is the in-link of the other and conversely.
To receive data, a device calls nfcsim_link_recv_skb() on its in-link
and waits for incoming data on a wait queue. To send data, a device
calls nfcsim_link_send_skb() on its out-link which stores the passed skb
and signals its wait queue. If the peer device was in the
nfcsim_link_recv_skb() call, it will be signaled and will be able to
pass the received sk_buff up to the Digital layer.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Tue, 7 Jun 2016 14:21:52 +0000 (16:21 +0200)]
NFC: digital: Add a delay between poll cycles
This replaces the polling work struct with a delayed work struct and add
a 10 ms delay between 2 poll cycles. This avoids to flood the device
with 'switch off'/'switch on' commands.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Tue, 7 Jun 2016 14:21:51 +0000 (16:21 +0200)]
NFC: port100: Explicitly set NFC-F framing for NFC-DEP
When setting the driver framing as NFC_DIGITAL_FRAMING_NFCF_NFC_DEP it
used to be already configured as NFC_DIGITAL_FRAMING_NFCF which is the
same. So this entry was empty in the in_protocols table.
Now that the digital stack can handle PLS requests, it can be changed
on the fly from NFC_DIGITAL_FRAMING_NFCA_NFC_DEP.
This patch explicitly defines the framing configuration values for
NFC_DIGITAL_FRAMING_NFCF_NFC_DEP.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: fdp: Detect errors from fdp_nci_create_conn()
drivers/nfc/fdp/fdp.c: In function ‘fdp_nci_patch_otp’:
drivers/nfc/fdp/fdp.c:373: warning: comparison is always false due to limited range of data type
drivers/nfc/fdp/fdp.c: In function ‘fdp_nci_patch_ram’:
drivers/nfc/fdp/fdp.c:444: warning: comparison is always false due to limited range of data type
fdp_nci_create_conn() may return a negative error code, which is
silently ignored by assigning it to a u8.
It used to be EXPORTed, but then EXPORT usage was cleaned up
(in 2012), without noticing that the function has no users at all
(and curiously, never had any users).
Delete it.
While at it, remove non-static "inline" hints on nearby functions:
these hints don't work across compilation units anyway,
and these functions are not used in their .c file, thus they are
never inlined. IOW: "inline" here does not help in any way.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> CC: Samuel Ortiz <sameo@linux.intel.com> CC: Christophe Ricard <christophe.ricard@gmail.com> CC: linux-wireless@vger.kernel.org CC: linux-kernel@vger.kernel.org Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Colin Ian King [Tue, 22 Mar 2016 23:17:00 +0000 (23:17 +0000)]
NFC: set info->ram_patch to NULL when it is released
When info->ram_patch is released info->otp_patch is being set
to NULL rather than info->ram_patch. I believe this is a cut-n-paste
bug from almost identical code proceeding it that uses the same
idiom for info->otp_patch.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
commit 8067302973a1 ("net-next: mediatek: add support for IRQ grouping")
failed to properly update the irq handling inside mtk_poll_controller()
causing compile errors if netconsole was enabled. Fix this by updating
the code to use the new separated irq handler function for RX.
Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 2 Jul 2016 19:21:22 +0000 (15:21 -0400)]
Merge branch 'mlxsw-router-interfaces-groundwork'
Jiri Pirko says:
====================
mlxsw: Lay the groundwork for the introduction of router interfaces
This is first patchset on a way to introduce ipv4 routing offload support
in mlxsw driver. Does preparations before router interfaces will
be introduced in mlxsw.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Add traps needed for router implementation
ip2me:
To instruct HW to send trapped ip2me traffic to kernel, we have to add
this trap. Selection ip2me traffic is introduced later on in this set.
ARPs:
We are going to stop flooding to CPU port when netdev isn't bridged and
only get packets destined to the netdev's IP address and certain control
packets.
Add traps for ARP request (broadcast) and response (unicast) in order to
get these to the CPU and resolve neighbours.
host miss:
If a packet is routed through a directly connected route and its
destination IP is not in the device's neighbour table, then we need to
trap it to CPU. This will cause the host to resolve the MAC of the
neighbour, which will be eventually programmed to the device's table.
router ingress:
In order to trap packets in router part.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Use action 'discard' when removing traps
When removing packet traps we should use action 'discard' instead of
'forward', as some trap IDs we'll add cannot be configured with the
later. However, result is the same, as packets are not trapped to the
CPU.
In the future we will be able to reverse the operation properly by
detaching the trap group from the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling the router in the device we will represent L3 netdevs
using router interfaces (RIFs). These will be specified whenever
programming routes or neighbours on the netdev.
Introduce the basic RIF infrastructure which allows one to lookup a RIF
by its netdev. Later patches in the series will extend this, but the
basic routines are needed now in order to direct traffic to CPU.
Pointers to the RIF structs are stored in an array indexed by the RIF's
number. This will allow us to efficiently update the kernel's neighbour
table when regularly dumping the device's table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Initialize ports at the end of init sequence
During ports initialization a net device is registered for each
available port, which implies the port is usable. However, a port is
only usable after the different parts of the device (e.g. flooding,
buffers) are initialized. This is especially important now, when we must
initialize the router before the ports, as otherwise the device can't be
initialized.
Solve that by initializing the switch ports at the end of init sequence.
Also, remove an unnecessary warning about port up/down events, which
would otherwise be invoked whenever removing the driver, as ports are
removed before unregistering the listener for these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Remove RIF from PVID vPort when joining / leaving LAG
We are going to assign router interfaces (RIFs) to netdevs if an IPv4
address was assigned to them. If one was assigned to a port netdev, this
will translate to the PVID vPort being member in a RIF.
While it's possible for a LAG slave to have an IP address, we can't have
a vPort being member in two FIDs (assuming the LAG device will be
put in bridge / assigned an IP address).
Solve that by making the PVID vPort leave any FID it might be a member
in when joining / leaving LAG.
Note that the PVID vPort is the only vPort that can be present on the
port when it's put under LAG.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN devices are created on top of LAG, their underlying vPorts are
configured correctly with LAG membership.
However, the PVID vPort is implicit and already present when the port
netdev is put under LAG, so its LAG membership is never set. Set it
correctly when joining / leaving LAG.
This didn't matter until now, but we are going to introduce support for
router interfaces (RIFs), which need to take into account LAG membership.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Remove VLANs configuration via SELF flag
When port isn't bridged it is still possible to invoke switchdev ops and
configure the device's VLAN filters.
However, this will require us to use different Router InterFaces (RIFs)
for the same netdev, instead of one per-netdev as with any other
configuration.
Taking the above into account and the fact that this functionality is
questionable with regards to the device's normal use-case, remove it and
instead return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Send untagged packets through a port netdev
Port netdevs (e.g. swXpY) that are not bridged are represented in the
device using a vPort with VID=PVID=1 (the PVID vPort), as untagged
packets entering the switch are internally tagged with the PVID VLAN.
When these packets are routed through a different port netdev they
should egress untagged.
This wasn't a problem until now, as non-bridged traffic only originated
from the CPU, which transmits packets out of the port as-is.
When a vPort is created with VID 1 mark it as egress untagged.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Swindell [Fri, 1 Jul 2016 22:46:24 +0000 (18:46 -0400)]
bnxt_en: Add support for firmware updates for additional processors.
Add support to the Ethtool FLASHDEV command handler for additional
firmware types to cover all the on-chip processors.
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Swindell [Fri, 1 Jul 2016 22:46:23 +0000 (18:46 -0400)]
bnxt_en: Request firmware reset after successful firwmare update
Upon successful mgmt processor firmware update, request a self
reset upon next PCIe reset (e.g. system reboot).
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Swindell [Fri, 1 Jul 2016 22:46:22 +0000 (18:46 -0400)]
bnxt_en: Add support for updating flash more securely
To support Secure Firmware Update, we must be able to allocate
a staging area in the Flash. This patch adds support for the
"update" type to tell firmware to do that.
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 1 Jul 2016 22:46:21 +0000 (18:46 -0400)]
bnxt_en: Do function reset on the 1st PF open only.
Calling the firmware to do function reset on the PF will kill all the VFs.
To prevent that, we call function reset on the 1st PF open before any VF
can be activated. On subsequent PF opens (with possibly some active VFs),
a bit has been set and we'll skip the function reset. VF driver will
always do function reset on every open. If there is an AER event, we will
always do function reset.
Signed-off-by: Michael Chan <michael.chan@broadocm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Fri, 1 Jul 2016 22:02:34 +0000 (00:02 +0200)]
net: ethernet: davinci_emac: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 2 Jul 2016 18:40:48 +0000 (14:40 -0400)]
Merge branch 'mlx5-next'
Saeed Mahameed says:
====================
Mellanox 100G SRIOV E-Switch offload and VF representors
We are happy to announce SRIOV E-Switch offload and VF netdev representors.
Or Gerlitz says:
Currently, the way SR-IOV embedded switches are dealt with in Linux is limited
in its expressiveness and flexibility, but this is not necessarily due to
hardware limitations. The kernel software model for controlling the SR-IOV
switch simply does not allow the configuration of anything more complex than
MAC/VLAN based forwarding.
Hence the benefits brought by SRIOV come at a price of management flexibility,
when compared to software virtual switches which are used in Para-Virtual (PV)
schemes and allow implementing complex policies and virtual topologies. Such
SW switching typically involved a complex per-packet processing within the host
kernel using subsystems such as TC, Bridge, Netfilter and Open-vswitch.
We'd like to change that and get the best of both worlds: the performance of SR-IOV
with the management flexibility of software switches. This will eventually include
a richer model for controlling the SR-IOV switch for flow-based switching and
tunneling. Under this model, the e-switch is configured dynamically and a fallback
to software exists in case the hardware is unable to offload all required flows.
This series from Hadar Hen-Zion and myself, is the 1st step in that direction,
specfically, it provides full control on the SRIOV embedded switching by host
software and paves the way to offload switching rules and polices with downstream
patches.
To allow for host based SW control on the SRIOV HW switch, we introduce per VF
representor host netdevice. The VF representor plays the same role as TAP devices
in PV setup. A packet send through the VF representor on the host arrives to
the VF, and a packet sent through the VF is received by its representor. The
administrator can hook the representor netdev into a kernel switching component.
Once they do that, packets from the VF are subject to steering (matching and
actions) of that software component."
Doing so indeed hurts the performance benefits of SRIOV as it forces all the
traffic to go through the hypervisor. However, this SW representation is what
would eventually allow us to introduce hybrid model, where we offload steering
for some of the VF/VM traffic to the HW while keeping other VM traffic to go
through the hypervisor. Examples for the latter are first packet of flows which
are needed for SW switches learning and/or matching against policy database or
types of traffic for which offloading is not desired or not supported by the
current HW eswitch generation.
The embedded switch is managed through a PCI device driver. As such, we introduce
a devlink/pci based scheme for setting the mode of the e-switch. The current mode
(where steering is done based on mac/vlan, etc) is referred to as "legacy" and the
new mode as "offloads".
For the mlx5 driver / ConnectX4 HW case, the VF representors implement a functional
subset of mlx5e Ethernet netdevices using their own profile. This design buys us robust
implementation with code reuse and sharing.
The representors are created by the host PCI driver when (1) in SRIOV and (2) the
e-switch is set to offloads mode. Currently, in mlx5 the e-switch management is done
through the PF vport (0) and hence the VF representors along with the existing PF
netdev which represents the uplink share the PCI PF device instance.
The series is built from two major components, the first relates to the e-switch
management and the second to VF representors.
We start with a refactoring that treats the existing SRIOV e-switch code as of operating
in legacy mode. Next, we add the code for the offloads mode which programs the e-switch
to operate in a way which serves for software based switching:
1. miss rule which matches all packets that do not match any HW other switching rule
and forwards them to the e-switch management port (0) for further processing.
2. infrastructure for send-to-vport rules which conceptually bypass other "normal"
steering rules which present at the e-switch datapath. Such rules apply only for packets
that originate in the e-switch manager vport (0).
Since all the VF reps run over the same e-switch port, we use more logic in the host PCI
driver to do HW steering of missed packets into the HW queue opened by a the respective VF
representor. Finally here, we add the devlink APIs to configure the e-switch mode.
The second part from Hadar starts with some refactoring work which allow for multiple
mlx5e NIC instances to be created over the same PCI function, use common resources
and avoid wrong loopbacks.
Next comes the heart of the change which is a profile definition which allow to practically
have both "conventional" mlx5e NIC use cases such as native mode (non SRIOV), VF, PF and VF
representor to share the Ethernet driver code. This is done by a small surgery that ended up
with few internal callbacks that should be implemented by a profile instance. The profile
for the conventional NIC is implemented, to preserve the existing functionality.
The last two patches add e-switch registration API for the VF representors and the
implementation of the VF representors netdevice profile. Being an mlx5e instance, the
VF representor uses HW send/recv queues, completions queues and such. It currently doesn't
support NIC offloads but some of them could be added later on. The VF representor has
switchdev ops, where currently the only supported API is the one to the HW ID,
which is needed to identify multiple representors belonging to the same e-switch.
The architecture + solution (software and firmware) work were done by a team consisting
of Ilya Lesokhin, Haggai Eran, Rony Efraim, Tal Anker, Natan Oppenheimer, Saeed Mahameed,
Hadar and Or, thanks you all!
v1 --> v2 fixes:
* removed unneeded variable (patch #3)
* removed unused value DEVLINK_ESWITCH_MODE_NONE (patch #8)
* changed the devlink mode name from "offloads" to "switchdev" which
better describes what are we referring here, using a known concept (patch #8)
* correctly refer to devlink e-switch modes (patch #10)
* use the correct mlx5e way to define the VF rep statistics (patch #16)
v2 --> v3 fixes:
* Rebased on top 6fde0e63eccb 'be2net: signedness bug in be_msix_enable()'
* Handled compilation error introduced by rebase on top "f5074d0ce2f8 Merge branch 'mlx5-100G-fixes'"
* This series applies perfectly even with 'mlx5 resiliency and xmit path fixes' merged to net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Fri, 1 Jul 2016 11:51:09 +0000 (14:51 +0300)]
net/mlx5e: Introduce SRIOV VF representors
Implement the relevant profile functions to create mlx5e driver instance
serving as VF representor. When SRIOV offloads mode is enabled, each VF
will have a representor netdevice instance on the host.
To do that, we also export set of shared service functions from en_main.c,
such that they can be used by both NIC and repsresentors netdevs.
The newly created representor netdevice has a basic set of net_device_ops
which are the same ndo functions as the NIC netdevice and an ndo of it's
own for phys port name.
The profiling infrastructure allow sharing code between the NIC and the
vport representor even though the representor has only a subset of the
NIC functionality.
The VF reps and the PF which is used in that mode to represent the uplink,
expose switchdev ops. Currently the only op supposed is attr get for the
port parent ID which here serves to identify net-devices belonging to the
same HW E-Switch. Other than that, no offloading is implemented and hence
switching functionality is achieved if one sets SW switching rules, e.g
using tc, bridge or ovs.
Port phys name (ndo_get_phys_port_name) is implemented to allow exporting
to user-space the VF vport number and along with the switchdev port parent
id (phys_switch_id) enable a udev base consistent naming scheme:
where phys_switch_id is exposed by the PF (and VF reps) and $PF_NIC is
the name of the PF netdevice.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are called by the mlx5e driver when the PF NIC is
created upon pci probe action regardless of the E-Switch mode (NONE,
LEGACY or OFFLOADS).
Adding basic E-Switch database that will hold the vport represntors
upon creation.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Fri, 1 Jul 2016 11:51:07 +0000 (14:51 +0300)]
net/mlx5e: Add support for multiple profiles
To allow support in representor netdevices where we create more than one
netdevice per NIC, add profiles to the mlx5e driver. The profiling
allows for creation of mlx5e instances with different characteristics.
Each profile implements its own behavior using set of function pointers
defined in struct mlx5e_profile. This is done to allow for avoiding complex
per profix branching in the code.
Currently only the profile for the conventional NIC is implemented,
which is of use when a netdev is created upon pci probe.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Fri, 1 Jul 2016 11:51:06 +0000 (14:51 +0300)]
net/mlx5e: Mark enabled RQTs instances explicitly
In the current driver implementation two types of receive queue
tables (RQTs) are in use - direct and indirect.
Change the driver to mark each new created RQT (direct or indirect)
as "enabled". This behaviour is needed for introducing new mlx5e
instances which serve to represent SRIOV VFs.
The VF representors will have only one type of RQTs (direct).
An "enabled" flag is added to each RQT to allow better handling
and code sharing between the representors and the nic netdevices.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Fri, 1 Jul 2016 11:51:05 +0000 (14:51 +0300)]
net/mlx5e: TIRs management refactoring
The current refresh tirs self loopback mechanism, refreshes all the tirs
belonging to the same mlx5e instance to prevent self loopback by packets
sent over any ring of that instance. This mechanism relies on all the
tirs/tises of an instance to be created with the same transport domain
number (tdn).
Change the driver to refresh all the tirs created under the same tdn
regardless of which mlx5e netdev instance they belong to.
This behaviour is needed for introducing new mlx5e instances which serve
to represent SRIOV VFs. The representors and the PF share vport used for
E-Switch management, and we want to avoid NIC level HW loopback between
them, e.g when sending broadcast packets. To achieve that, both the
representors and the PF NIC will share the tdn.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Fri, 1 Jul 2016 11:51:04 +0000 (14:51 +0300)]
net/mlx5e: Create NIC global resources only once
To allow creating more than one netdev over the same PCI function, we
change the driver such that global NIC resources are created once and
later be shared amongst all the mlx5e netdevs running over that port.
Move the CQ UAR, PD (pdn), Transport Domain (tdn), MKey resources from
being kept in the mlx5e priv part to a new resources structure
(mlx5e_resources) placed under the mlx5_core device.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:51:03 +0000 (14:51 +0300)]
net/mlx5e: Add devlink based SRIOV mode changes
Implement handlers for the devlink commands to get and set the SRIOV
E-Switch mode.
When turning to the switchdev/offloads mode, we disable the e-switch
and enable it again in the new mode, create the NIC offloads table
and create VF reps.
When turning to legacy mode, we remove the VF reps and the offloads
table, and re-initiate the e-switch in it's legacy mode.
The actual creation/removal of the VF reps is done in downstream patches.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:51:02 +0000 (14:51 +0300)]
net/mlx5: Add devlink interface
The devlink interface is initially used to set/get the mode of the SRIOV e-switch.
Currently, these are only stubs for get/set, down-stream patch will actually
fill them out.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:51:01 +0000 (14:51 +0300)]
net/devlink: Add E-Switch mode control
Add the commands to set and show the mode of SRIOV E-Switch, two modes
are supported:
* legacy: operating in the "old" L2 based mode (DMAC --> VF vport)
* switchdev: the E-Switch is referred to as whitebox switch configured
using standard tools such as tc, bridge, openvswitch etc. To allow
working with the tools, for each VF, a VF representor netdevice is
created by the E-Switch manager vendor device driver instance (e.g PF).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:51:00 +0000 (14:51 +0300)]
net/mlx5: E-Switch, Add API to create vport rx rules
Add the API to create vport rx rules of the form
packet meta-data :: vport == $VPORT --> $TIR
where the TIR is opened by this VF representor.
This logic will by used for packets that didn't match any rule in the
e-switch datapath and should be received into the host OS through the
netdevice that represents the VF they were sent from.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:50:59 +0000 (14:50 +0300)]
net/mlx5: E-Switch, Add offloads table
Belongs to the NIC offloads name-space, and to be used as part of the
SRIOV offloads logic to steer packets that hit the e-switch miss rule
to the TIR of the relevant VF representor.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:50:58 +0000 (14:50 +0300)]
net/mlx5: Introduce offloads steering namespace
Add a new namespace (MLX5_FLOW_NAMESPACE_OFFLOADS) to be populated
with flow steering rules that deal with rules that have have to
be executed before the EN NIC steering rules are matched.
The namespace is located after the bypass name-space and before the
kernel name-space. Therefore, it precedes the HW processing done for
rules set for the kernel NIC name-space.
Under SRIOV, it would allow us to match on e-switch missed packet
and forward them to the relevant VF representor TIR.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Amir Vadai <amir@vadai.me> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
These rules are to be used for a send-to-vport logic which conceptually bypasses
the "normal" steering rules currently present at the e-switch datapath.
Such rule should apply only for packets that originate in the e-switch manager
vport (0) and are sent for a given SQN which is used by a given VF representor
device, and hence the matching logic.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:50:56 +0000 (14:50 +0300)]
net/mlx5: E-Switch, Add miss rule for offloads mode
In the sriov offloads mode, packets that are not matched by any other
rule should be sent towards the e-switch manager for further processing.
Add such "miss" rule which matches ANY packet as the last rule in the
e-switch FDB and programs the HW to send the packet to vport 0 where
the e-switch manager runs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:50:55 +0000 (14:50 +0300)]
net/mlx5: E-Switch, Add support for the sriov offloads mode
Unlike the legacy mode, here, forwarding rules are not learned by the
driver per events on macs set by VFs/VMs into their vports, but rather
should be programmed by higher-level SW entities.
Saying that, still, in the offloads mode (SRIOV_OFFLOADS), two flow
groups are created by the driver for management (slow path) purposes:
The first group will be used for sending packets over e-switch vports
from the host OS where the e-switch management code runs, to be
received by VFs.
The second group will be used by a miss rule which forwards packets toward
the e-switch manager. Further logic will trap these packets such that
the receiving net-device as seen by the networking stack is the representor
of the vport that sent the packet over the e-switch data-path.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Fri, 1 Jul 2016 11:50:54 +0000 (14:50 +0300)]
net/mlx5: E-Switch, Add operational mode to the SRIOV e-Switch
Define three modes for the SRIOV e-switch operation, none (SRIOV_NONE,
none of the VF vports are enabled), legacy (SRIOV_LEGACY, the current mode)
and sriov offloads (SRIOV_OFFLOADS). Currently, when in SRIOV, only the
legacy mode is supported, where steering rules are of the form:
destination mac --> VF vport
This patch does not change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 1 Jul 2016 09:34:13 +0000 (17:34 +0800)]
net: hns: get reset registers from DT
Since the registers of subctrl may be different, it is better to
mv the registers from hns mdio driver routine to device tree node.
Signed-off-by: Kejian Yan <yankejian@huawei.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kejian Yan [Fri, 1 Jul 2016 09:34:12 +0000 (17:34 +0800)]
net: hns: add media-type property for hns
It is PORT_TP type if the service port is GE mode. It is wrong to
judge the port type by using if it is service port. Adding the media
type to know port type.
Reported-by: Jinchuan Tian <tianjinchuan1@huawei.com> Signed-off-by: Kejian Yan <yankejian@huawei.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The sequence of hns_mac_dev_to_enet_if() is the same as
hns_get_enet_interface(), and hns_get_enet_interface() is called
by initialization to get the mac mode. And the mode is not changed
anywhere. Thus add hns_mac_dev_to_enet_if() function to get the mac
mode is obviously redundant.
Reported-by: Jinchuan Tian <tianjinchuan1@huawei.com> Signed-off-by: Kejian Yan <yankejian@huawei.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are two approaches to assign data, one does 2 loops, another
does 1 loop. This patch normalize the different methods to 1 loop.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In comment line, some time miss a space before */, so this
patch adds a space before */.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According to the previous review comments from Andy, this patch
deletes the redundant parens in the patch.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes code sytle of hns driver to make it
simple.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds maintainers for hisilicon network subsystem driver
Signed-off-by: Daode Huang <huangdaode@hisilicon.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Jul 2016 20:45:24 +0000 (16:45 -0400)]
Merge branch 'rds-multipath-datastructures'
Sowmini Varadhan says:
====================
RDS:TCP data structure changes for multipath support
The second installment of changes to enable multipath support in
RDS-TCP. This series implements the changes in rds-tcp so that the
rds_conn_path has a pointer to the rds_tcp_connection in cp_transport_data.
Struct rds_tcp_connection keeps track of the inet_sk per path in
t_sock. The ->sk_user_data in turn is a pointer to the rds_conn_path.
With this set of changes, rds_tcp has the needed plumbing to handle
multiple paths(socket) per rds_connection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:18 +0000 (16:11 -0700)]
RDS: Do not send a pong to an incoming ping with 0 src port
RDS ping messages are sent with a non-zero src port to a zero
dst port, so that the rds pong messages can be sent back to the
originators src port. However if a confused/malicious sender
sends a ping with a 0 src port, we'd have an infinite ping-pong
loop. To avoid this, the receiver should ignore ping messages
with a 0 src port.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:17 +0000 (16:11 -0700)]
RDS: TCP: Simplify reconnect to avoid duelling reconnnect attempts
When reconnecting, the peer with the smaller IP address will initiate
the reconnect, to avoid needless duelling SYN issues.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:16 +0000 (16:11 -0700)]
RDS: TCP: Hooks to set up a single connection path
This patch adds ->conn_path_connect callbacks in the rds_transport
that are used to set up a single connection path.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:15 +0000 (16:11 -0700)]
RDS: TCP: make receive path use the rds_conn_path
The ->sk_user_data contains a pointer to the rds_conn_path
for the socket. Use this consistently in the rds_tcp_data_ready
callbacks to get the rds_conn_path for rds_recv_incoming.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:14 +0000 (16:11 -0700)]
RDS: TCP: make ->sk_user_data point to a rds_conn_path
The socket callbacks should all operate on a struct rds_conn_path,
in preparation for a MP capable RDS-TCP.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:13 +0000 (16:11 -0700)]
RDS: TCP: Refactor connection destruction to handle multiple paths
A single rds_connection may have multiple rds_conn_paths that have
to be carefully and correctly destroyed, for both rmmod and
netns-delete cases.
For both cases, we extract a single rds_tcp_connection for
each conn into a temporary list, and then invoke rds_conn_destroy()
which iteratively dismantles every path in the rds_connection.
For the netns deletion case, we additionally have to make sure
that we do not leave a socket in TIME_WAIT state, as this will
hold up the netns deletion. Thus we call rds_tcp_conn_paths_destroy()
to reset state quickly.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:12 +0000 (16:11 -0700)]
RDS: TCP: Make rds_tcp_connection track the rds_conn_path
The struct rds_tcp_connection is the transport-specific private
data structure that tracks TCP information per rds_conn_path.
Modify this structure to have a back-pointer to the rds_conn_path
for which it is the ->cp_transport_data.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:11 +0000 (16:11 -0700)]
RDS: TCP: Remove dead logic around c_passive in rds-tcp
The c_passive bit is only intended for the IB transport and will
never be encountered in rds-tcp, so remove the dead logic that
predicates on this bit.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 30 Jun 2016 23:11:10 +0000 (16:11 -0700)]
RDS: Rework path specific indirections
Refactor code to avoid separate indirections for single-path
and multipath transports. All transports (both single and mp-capable)
will get a pointer to the rds_conn_path, and can trivially derive
the rds_connection from the ->cp_conn.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Jul 2016 20:32:27 +0000 (16:32 -0400)]
Merge branch 'bpf-cgroup2'
Martin KaFai Lau says:
====================
cgroup: bpf: cgroup2 membership test on skb
This series is to implement a bpf-way to
check the cgroup2 membership of a skb (sk_buff).
It is similar to the feature added in netfilter: c38c4597e4bf ("netfilter: implement xt_cgroup cgroup2 path match")
The current target is the tc-like usage.
v3:
- Remove WARN_ON_ONCE(!rcu_read_lock_held())
- Stop BPF_MAP_TYPE_CGROUP_ARRAY usage in patch 2/4
- Avoid mounting bpf fs manually in patch 4/4
- Thanks for Daniel's review and the above suggestions
- Check CONFIG_SOCK_CGROUP_DATA instead of CONFIG_CGROUPS. Thanks to
the kbuild bot's report.
Patch 2/4 only needs CONFIG_CGROUPS while patch 3/4 needs
CONFIG_SOCK_CGROUP_DATA. Since a single bpf cgrp2 array alone is
not useful for now, CONFIG_SOCK_CGROUP_DATA is also used in
patch 2/4. We can fine tune it later if we find other use cases
for the cgrp2 array.
- Return EAGAIN instead of ENOENT if the cgrp2 array entry is
NULL. It is to distinguish these two cases: 1) the userland has
not populated this array entry yet. or 2) not finding cgrp2 from the skb.
- Be-lated thanks to Alexei and Tejun on reviewing v1 and giving advice on
this work.
v2:
- Fix two return cases in cgroup_get_from_fd()
- Fix compilation errors when CONFIG_CGROUPS is not used:
- arraymap.c: avoid registering BPF_MAP_TYPE_CGROUP_ARRAY
- filter.c: tc_cls_act_func_proto() returns NULL on BPF_FUNC_skb_in_cgroup
- Add comments to BPF_FUNC_skb_in_cgroup and cgroup_get_from_fd()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 30 Jun 2016 17:28:45 +0000 (10:28 -0700)]
cgroup: bpf: Add an example to do cgroup checking in BPF
test_cgrp2_array_pin.c:
A userland program that creates a bpf_map (BPF_MAP_TYPE_GROUP_ARRAY),
pouplates/updates it with a cgroup2's backed fd and pins it to a
bpf-fs's file. The pinned file can be loaded by tc and then used
by the bpf prog later. This program can also update an existing pinned
array and it could be useful for debugging/testing purpose.
test_cgrp2_tc_kern.c:
A bpf prog which should be loaded by tc. It is to demonstrate
the usage of bpf_skb_in_cgroup.
test_cgrp2_tc.sh:
A script that glues the test_cgrp2_array_pin.c and
test_cgrp2_tc_kern.c together. The idea is like:
1. Load the test_cgrp2_tc_kern.o by tc
2. Use test_cgrp2_array_pin.c to populate a BPF_MAP_TYPE_CGROUP_ARRAY
with a cgroup fd
3. Do a 'ping -6 ff02::1%ve' to ensure the packet has been
dropped because of a match on the cgroup
Most of the lines in test_cgrp2_tc.sh is the boilerplate
to setup the cgroup/bpf-fs/net-devices/netns...etc. It is
not bulletproof on errors but should work well enough and
give enough debug info if things did not go well.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Alexei Starovoitov <ast@fb.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Tejun Heo <tj@kernel.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 30 Jun 2016 17:28:44 +0000 (10:28 -0700)]
cgroup: bpf: Add bpf_skb_in_cgroup_proto
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4bf ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Alexei Starovoitov <ast@fb.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Tejun Heo <tj@kernel.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 30 Jun 2016 17:28:43 +0000 (10:28 -0700)]
cgroup: bpf: Add BPF_MAP_TYPE_CGROUP_ARRAY
Add a BPF_MAP_TYPE_CGROUP_ARRAY and its bpf_map_ops's implementations.
To update an element, the caller is expected to obtain a cgroup2 backed
fd by open(cgroup2_dir) and then update the array with that fd.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Alexei Starovoitov <ast@fb.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Tejun Heo <tj@kernel.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 30 Jun 2016 17:28:42 +0000 (10:28 -0700)]
cgroup: Add cgroup_get_from_fd
Add a helper function to get a cgroup2 from a fd. It will be
stored in a bpf array (BPF_MAP_TYPE_CGROUP_ARRAY) which will
be introduced in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Alexei Starovoitov <ast@fb.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Tejun Heo <tj@kernel.org> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log