Daniel Vetter [Wed, 26 Nov 2014 15:57:41 +0000 (16:57 +0100)]
drm/atomic-helper: Export both plane and modeset check helpers
The default call sequence for these two parts won't fit for all
drivers. So export the two pieces and explain with a bit of kerneldoc
when each should be called.
v2: Squash in fixup from Rob to actually add the newly exported
functions to headers
Cc: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Dave Airlie [Fri, 12 Dec 2014 23:18:02 +0000 (09:18 +1000)]
Merge branch 'drm-sti-next-2014-12-11' of http://git.linaro.org/people/benjamin.gaignard/kernel into drm-next
This series of patches fix various issues in STI drm driver.
Now HDMI i2c adapter could be selected in device tree
and plug detection doesn't use gpio anymore.
I also had fix some signal timing problems after testing the driver
on more hardware.
The remaining patches attemps to simplify the code and prepare
the next evolutions like DVO and auxiliary CRTC support
* 'drm-sti-next-2014-12-11' of http://git.linaro.org/people/benjamin.gaignard/kernel:
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
Dave Airlie [Fri, 12 Dec 2014 01:39:49 +0000 (11:39 +1000)]
Merge tag 'drm-intel-next-fixes-2014-12-11' of git://anongit.freedesktop.org/drm-intel into drm-next
Here's a batch of i915 fixes for 3.19.
* tag 'drm-intel-next-fixes-2014-12-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
drm/i915: Don't complain about stolen conflicts on gen3
drm/i915: resume MST after reading back hw state
drm/i915: Handle inaccurate time conversion issues
drm/i915: compute wait_ioctl timeout correctly
drm/i915: don't always do full mode sets when infoframes are enabled
Jesse Barnes [Wed, 10 Dec 2014 20:16:05 +0000 (12:16 -0800)]
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
Should probably just init this in the GMbus code all the time, based on
the cdclk and HPLL like we do on newer platforms. Ville has code for
that in a rework branch, but until then we can fix this bug fairly
easily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76301 Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Nikolay <mar.kolya@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Jani Nikula <jani.nikula@intel.com>
High Quality Video Data Plane is hardware IP dedicated
to video rendering. Compare to GPD (graphic planes) it
have better scaler capabilities.
HQVDP use VID layer to push data into hardware compositor
without going into DDR. From data flow point of view HQVDP
and VID are nested so HQVPD update/disable VID.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
For stih407 SoC enable the second mixer to get two CRTC.
Allow GPD planes and encoders to be connected to this new CRTC.
Cursor plane can only be set on first CRTC.
GPD clocks needed change the parent clock depending on which
CRTC GPD are used.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
The HDMI path introduce a delay of 6 pixels.
This delay should be take into account while programming
VTG for the HDMI. Without this delay, the HDMI active
window area is shift of 6 pixel on the right.
Set also timing for DVO output.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Dave Airlie [Thu, 11 Dec 2014 00:12:57 +0000 (10:12 +1000)]
Merge tag 'topic/core-stuff-2014-12-10' of git://anongit.freedesktop.org/drm-intel into drm-next
Merge drm core fixes from Daniel.
* tag 'topic/core-stuff-2014-12-10' of git://anongit.freedesktop.org/drm-intel:
drm: Zero out DRM object memory upon cleanup
drm: fix a typo in a comment
drm: fix a word repetition in a comment
drm: Fix memory leak at error path of drm_read()
drm/Documentation: Fix rowspan value in drm-kms-properties
drm/edid: Restore kerneldoc consistency
drm/edid: new drm_edid_block_checksum helper function V3
drm/edid: shorten log output in case of all zeroes edid block
drm/edid: move drm_edid_is_zero to top, make edid argument const
Thierry Reding [Wed, 10 Dec 2014 10:38:49 +0000 (11:38 +0100)]
drm: Zero out DRM object memory upon cleanup
Drivers where the DRM objects have a lifetime that extends beyond that
of the DRM device need to zero out the DRM object memory to void stale
data such as properties. The DRM core code expects to operate on newly
allocated and zeroed out objects and will behave unexpectedly, such as
add duplicate properties, otherwise.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
(0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
[-Wshift-overflow]
WA_SET_BIT_MASKED(GEN7_GT_MODE,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
'WA_SET_BIT_MASKED'
WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)
Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.
The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.
To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.
This bug was introduced when reworking the WA emission in:
drm/i915: Build workaround list in ring initialization
v2: Invert the order of the mask and value arguments (Daniel Vetter)
Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
_MASKED_FIELD() (Jani Nikula)
Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
Add check to ensure the value is within the mask boundaries (Chris Wilson)
v3: Ensure the the value and mask are 16 bits (Dave Gordon)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Arun Siluvery <arun.siluvery@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Daniel Vetter [Fri, 11 Apr 2014 13:55:17 +0000 (15:55 +0200)]
drm/i915: Don't complain about stolen conflicts on gen3
Apparently stuff works that way on those machines.
I agree with Chris' concern that this is a bit risky but imo worth a
shot in -next just for fun. Afaics all these machines have the pci
resources allocated like that by the BIOS, so I suspect that it's all
ok.
Martin Peres [Tue, 9 Dec 2014 07:13:09 +0000 (08:13 +0100)]
drm: fix a typo in a comment
Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Mon, 8 Dec 2014 23:58:51 +0000 (09:58 +1000)]
Merge branch 'drm-mst-next' of ssh://people.freedesktop.org/~/linux into drm-next
Merge mst tiling patches and MST fixes
* 'drm-mst-next' of ssh://people.freedesktop.org/~/linux:
drm/fb: add support for tiled monitor configurations. (v2)
drm/tile: expose the tile property to userspace (v3)
drm/connector: store tile information from displayid (v3)
drm/mst: cached EDID for logical ports (v2)
drm: add tile_group support. (v3)
drm/displayid: add displayid defines and edid extension (v2)
drm/dp-mst: Remove branches before dropping the reference
drm/fb_helper: move deferred fb checking into restore mode (v2)
drm/dp: retry AUX transactions 32 times (v1.1)
Dave Airlie [Mon, 20 Oct 2014 06:17:17 +0000 (16:17 +1000)]
drm: add tile_group support. (v3)
A tile group is an identifier shared by a single monitor,
DisplayID topology has 8 bytes we can use for this, just
use those for now until something else comes up in the
future. We assign these to an idr and use the idr to
tell userspace what connectors are in the same tile group.
DisplayID v1.3 says the serial number must be unique for
displays from the same manufacturer.
v2:
destroy idr (dvdhrm)
add docbook (danvet)
airlied:- not sure how to make docbook add fns to tile group section.
v3: fix missing unlock.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter [Mon, 8 Dec 2014 21:55:22 +0000 (22:55 +0100)]
drm/dp-mst: Remove branches before dropping the reference
When we unplug a dp mst branch we unreference the entire tree from
the root towards the leaves. Which is ok, since that's the way the
pointers and so also the refcounts go.
But when we drop the reference we must make sure that we remove the
branches/ports from the lists/pointers before dropping the reference.
Otherwise the get_validated functions will still return it instead
of returning NULL (which indicates a potentially on-going unplug).
The mst branch destroy gets this right for ports: First it deletes
the port from the ports list, then it unrefs. But the ports destroy
function gets it wrong: First it unrefs, then it drops the ref. Which
means a zombie mst branch can still be validate with get_validated_mstb_ref
when it shouldn't.
Fix this.
This should address a backtrace Dave dug out somewhere on unplug:
Dave Airlie [Wed, 26 Nov 2014 03:15:24 +0000 (13:15 +1000)]
drm/fb_helper: move deferred fb checking into restore mode (v2)
On MST systems the monitors don't appear when we set the fb up,
but plymouth opens the drm device and holds it open while they
come up, when plymouth finishes and lastclose gets called we
don't do the delayed fb probe, so the monitor never appears on the
console.
Fix this by moving the delayed checking into the mode restore.
v2: Daniel suggested that ->delayed_hotplug is set under
the mode_config mutex, so we should check it under that as
well, while we are in the area.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Wed, 26 Nov 2014 03:13:09 +0000 (13:13 +1000)]
drm/dp: retry AUX transactions 32 times (v1.1)
At least on two MST devices I've tested with, when
they are link training downstream, they are totally
unable to handle aux ch msgs, so they defer like nuts.
I tried 16, it wasn't enough, 32 seems better.
This fixes one Dell 4k monitor and one of the
MST hubs.
v1.1: fixup comment (Tom).
Acked-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 8 Dec 2014 03:23:37 +0000 (13:23 +1000)]
drm/i915: resume MST after reading back hw state
Otherwise the MST resume paths can hit DPMS paths
which hit state checker paths, which hit WARN_ON,
because the state checker is inconsistent with the
hw.
This fixes a bunch of WARN_ON's on resume after
undocking.
Signed-off-by: Dave Airlie <airlied@redhat.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Dave Airlie [Mon, 8 Dec 2014 03:40:51 +0000 (13:40 +1000)]
Merge branch 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux into drm-next
As discussed on irc, I'm sending a pull request with one important change:
- Disable support for 32-bit user processes. This is done due to AMD's decision
to remove support for 32-bit user processes on Linux for its HSA stack.
* 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux:
amdkfd: Disable support for 32-bit user processes
Dave Airlie [Mon, 8 Dec 2014 00:33:52 +0000 (10:33 +1000)]
Merge tag 'v3.18' into drm-next
Linux 3.18
Backmerge Linus tree into -next as we had conflicts in i915/radeon/nouveau,
and everyone was solving them individually.
* tag 'v3.18': (57 commits)
Linux 3.18
watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
uapi: fix to export linux/vm_sockets.h
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
ahci: disable MSI on SAMSUNG 0xa800 SSD
context_tracking: Restore previous state in schedule_user
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
...
Linus Torvalds [Sun, 7 Dec 2014 20:00:14 +0000 (12:00 -0800)]
Merge branch 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Three libata fixes for v3.18. Nothing too interesting. PCI ID ID and
quirk additions to ahci and an error handling path fix in sata_fsl"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable MSI on SAMSUNG 0xa800 SSD
sata_fsl: fix error handling of irq_of_parse_and_map
AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller
Linus Torvalds [Sat, 6 Dec 2014 19:26:01 +0000 (11:26 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are two more driver bugfixes for I2C which would be good to have"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
Linus Torvalds [Fri, 5 Dec 2014 18:47:19 +0000 (10:47 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two final fixlets for 3.18:
- Prevent microcode reload wreckage on 32bit
- Unbreak cross compilation"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode: Limit the microcode reloading to 64-bit for now
x86: Use $(OBJDUMP) instead of plain objdump
Daniel Vetter [Fri, 28 Nov 2014 09:29:55 +0000 (10:29 +0100)]
drm/i915: Handle inaccurate time conversion issues
So apparently jiffies<->nsec<->ktime isn't accurate or something. At
elast if we timeout there's occasionally still a few hundred us left
(in a 2 second timeout).
Stuff I've tried and thrown out again:
- Sampling the before timestamp before jiffies. Doesn't improve test
path rate at all.
- Using jiffies. Way to inaccurate, which means way too much drift
with signals plus automatic ioctl restarting in userspace. In
hindsight we should have used an absolute timeout, but hey we need
something for v3 of the i915 gem wait interfaces ;-)
- Trying to figure out where accuracy gets lost. gl testcase really
don't care all that much about this (as long as isn't not massively
off), it's just that the testcase gets a bit upset if it receives an
EITME with timeout > 0.
So as long as we're in the ballbark it's good enough. So patch
everything up if we're at most one jiffies off. I get's me a solid
test again.
Use ktime_get_raw_ns() and get rid of the back and forth timespec
conversions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: John Stultz <john.stultz@linaro.org>
Probably because I'm too lazy to confirm myself and still waiting for
QA ;-)
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82749 Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use ktime_get_raw_ns() and get rid of the back and forth timespec
conversions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: John Stultz <john.stultz@linaro.org>
So fix this up by reinstating our handrolled _timeout function. While
at it bother with handling MAX_JIFFIES.
v2: Convert to usecs (we don't care about the accuracy anyway) first
to avoid overflow issues Dave Gordon spotted.
v3: Drop the explicit MAX_JIFFY_OFFSET check, usecs_to_jiffies should
take care of that already. It might be a bit too enthusiastic about it
though.
v4: Chris has a much nicer color, so use his implementation.
This requires to export nsec_to_jiffies from time.c.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Dave Gordon <david.s.gordon@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82749 Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Acked-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Linus Torvalds [Fri, 5 Dec 2014 06:39:37 +0000 (22:39 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm intel fixes from Dave Airlie:
"Two intel stable fixes, that should be it from me for this round"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Linus Torvalds [Fri, 5 Dec 2014 01:48:13 +0000 (17:48 -0800)]
Merge tag 'pm+acpi-3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI backlight fix from Rafael Wysocki:
"This is a simple fix for an ACPI backlight regression introduced by a
recent commit that overlooked a corner case which should have been
taken into account"
* tag 'pm+acpi-3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: update condition to check if device is in _DOD list
Dave Airlie [Fri, 5 Dec 2014 01:12:29 +0000 (11:12 +1000)]
Merge tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Silence some pch fifo underrun reports and panel locking backtraces,
both cc: stable.
* tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Dave Airlie [Fri, 5 Dec 2014 01:11:57 +0000 (11:11 +1000)]
Merge tag 'drm-intel-next-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel into drm-next
Fixes for 3.20. I did stick the gen3/4 reset work from Ville in because we
have an awful lot of gen4 mesa hangs, and with this reset should also work
on vintage i965g/gm (we already have reset for g4x/gen4.5). So should help
to appease users suffering from these hangs. Otherwise all over.
This is the last 3.20 pull from me, from here on Jani will take over. By Ville Syrjälä (8) and others
* tag 'drm-intel-next-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Reject modeset when the same digital port is used more than once
drm/i915: mask RPS IRQs properly when disabling RPS
drm/i915: Tune down spurious CRC interrupt warning
drm/i915: Fix context object leak for legacy contexts
drm/i915/skl: Update in Gen9 multi-engine forcewake range
drm/i915/eDP: When enabling panel VDD cancel pending disable worker
drm/i915: Handle runtime pm in the CRC setup code
drm/i915: Disable crtcs gracefully before GPU reset on gen3/4
drm/i915: Grab modeset locks for GPU rest on pre-ctg
drm/i915: Implement GPU reset for g33
drm/i915: Implement GPU reset for 915/945
drm/i915: Restore the display config after a GPU reset on gen4
drm/i915: Fix gen4 GPU reset
drm/i915: Stop gathering error states for CS error interrupts
drm/i915: Disallow pin ioctl completely for kms drivers
drm/i915: Only warn the first time we attempt to mmio whilst suspended
drm/i915/chv: Enable AVI, SPD and HDMI infoframes for CHV.
drm/i915: Don't clobber crtc->new_config when nothing changes
Dave Airlie [Fri, 5 Dec 2014 01:10:59 +0000 (11:10 +1000)]
Merge branch 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux into drm-next
Just three more fixes for 3.19.
This is the last request until -rc1. I will have our QA team run a full
HSA stack test on 3.19-rc1 and if we find problems, I will send a fixes pull
request.
* 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux:
amdkfd: Set *buffer_ptr to NULL in case of error
amdkfd: use atomic allocations within srcu callbacks
amdkfd: use sizeof(long) granularity for the pasid bitmask
Dave Airlie [Fri, 5 Dec 2014 01:08:31 +0000 (11:08 +1000)]
Merge branch 'drm-next-3.19-wip' of git://people.freedesktop.org/~agd5f/linux into drm-next
- More cursor and hotspot handling fixes
- Fix some typos in the new smc fan control code and enable on CI
- VM and CS cleanups
* 'drm-next-3.19-wip' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: enable smc fan control on CI
drm/radeon: use pointers instead of indexes for CS chunks
drm/radeon: remove duplicates check
drm/ttm: optionally move duplicates to a separate list
drm/radeon: check the right ring in radeon_evict_flags()
drm/radeon: fix copy paste typos in fan control for si/ci
drm/radeon: Hide cursor on CRTCs used by fbdev (v2)
drm/radeon: add spinlock for BO_VA status protection (v2)
drm/radeon: fence PT updates as shared
drm/radeon: rename radeon_cs_reloc to radeon_bo_list
drm/radeon: drop the handle from radeon_cs_reloc
drm/radeon drop gobj from radeon_cs_reloc
drm/radeon: fix typo in new fan control registers for SI/CI
drm/radeon: sync all BOs involved in a CS
drm/radeon: Move hotspot handling out of radeon_set_cursor
drm/radeon: Re-show the cursor after a modeset
Linus Torvalds [Fri, 5 Dec 2014 00:06:02 +0000 (16:06 -0800)]
Merge tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A core fix and some driver fixes:
- regression fix in Remote Controller core affecting RC6 protocol
handling
- fix video buffer handling in cx23885
- race fix in solo6x10
- fix image selection in smiapp
- fix reported payload size on s2255drv
- two updates for MAINTAINERS file"
* tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] rc-core: fix toggle handling in the rc6 decoder
MAINTAINERS: Update mchehab's addresses
[media] cx23885: use sg = sg_next(sg) instead of sg++
[media] s2255drv: fix payload size for JPG, MJPEG
[media] Update MAINTAINERS for solo6x10
[media] solo6x10: fix a race in IRQ handler
[media] smiapp: Only some selection targets are settable
Masahiro Yamada [Thu, 4 Dec 2014 22:42:25 +0000 (14:42 -0800)]
uapi: fix to export linux/vm_sockets.h
A typo "header=y" was introduced by commit 7071cf7fc435 ("uapi: add
missing network related headers to kbuild").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vishnu Motghare [Wed, 3 Dec 2014 12:35:25 +0000 (18:05 +0530)]
i2c: cadence: Set the hardware time-out register to maximum value
Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
i2c: davinci: generate STP always when NACK is received
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26eb ("i2c: omap: query STP always when NACK is received").
Tejun Heo [Thu, 4 Dec 2014 18:13:28 +0000 (13:13 -0500)]
ahci: disable MSI on SAMSUNG 0xa800 SSD
Just like 0x1600 which got blacklisted by 66a7cbc303f4 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled. Disable MSI.
Takashi Iwai [Thu, 4 Dec 2014 10:56:42 +0000 (11:56 +0100)]
drm: Fix memory leak at error path of drm_read()
Note that the read manpages explicitly states that the read position
is undefined on error. Since EFAULT is just a userspace bug we are
therefore fine with just dropping the event on the floor.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[danvet: Add note that just dropping the event is ok.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Oded Gabbay [Thu, 4 Dec 2014 12:09:02 +0000 (14:09 +0200)]
amdkfd: Set *buffer_ptr to NULL in case of error
In function acquire_packet_buffer() we may return -ENOMEM. In that case, we
should set the *buffer_ptr to NULL, so that calling functions which check the
*buffer_ptr value as a criteria for success, will know that
acquire_packet_buffer() failed.
Sean Paul [Wed, 3 Dec 2014 19:57:40 +0000 (11:57 -0800)]
drm/Documentation: Fix rowspan value in drm-kms-properties
The "DRM" rowspan wasn't updated in commit cc7096fb6d1d (drm/mode: document path
property and function to set it. (v1.1)), so increment it by one to fix the
table.
Cc: Dave Airlie <airlied@linux.ie> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Andy Lutomirski [Wed, 3 Dec 2014 23:37:08 +0000 (15:37 -0800)]
context_tracking: Restore previous state in schedule_user
It appears that some SCHEDULE_USER (asm for schedule_user) callers
in arch/x86/kernel/entry_64.S are called from RCU kernel context,
and schedule_user will return in RCU user context. This causes RCU
warnings and possible failures.
This is intended to be a minimal fix suitable for 3.18.
Reported-and-tested-by: Dave Jones <davej@redhat.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Frédéric Weisbecker <fweisbec@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian König [Wed, 3 Dec 2014 14:46:48 +0000 (15:46 +0100)]
drm/ttm: optionally move duplicates to a separate list
This patch adds an optional list_head parameter to ttm_eu_reserve_buffers.
If specified duplicates in the execbuf list are no longer reported as errors,
but moved to this list instead.
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Wed, 3 Dec 2014 22:08:50 +0000 (14:08 -0800)]
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree bugfix from Grant Likely:
"One more bug fix for v3.18. I debated whether or not to send you this
merge request because we're at such a late rc. The bug isn't critical
in that there is only one system known to be affected and the patch is
easy to backport. The codepath is used by pretty much every DT based
system, so there is risk a of regression (it /should/ be safe, but
I've been bitten by stuff that should be safe before). I've had it in
linux-next for a week and haven't received any complaints.
I think it probably should just be merged right away rather than
waiting for the merge window and backporting. It does fix a real bug
and the code is theoretically safer after the change. I can't think
of any situation where it would be dangerous to reserve the DT memory
an extra time.
Summary from tag:
Single bugfix for boot failure seen in the wild. The memory reserve
code tries to be clever about reserving the FDT, but it should just
go ahead and reserve it unconditionally to avoid the problem of
partial overlap described in the patch"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap
Linus Torvalds [Wed, 3 Dec 2014 22:05:24 +0000 (14:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block core regression fix from Jens Axboe:
"Single fix for a regression introduced in this development cycle,
where dm on top of dif/dix is broken. From Darrick Wong"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix regression where bio_integrity_process uses wrong bio_vec iterator
Linus Torvalds [Wed, 3 Dec 2014 21:51:50 +0000 (13:51 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and Nouveau fixes:
So nouveau had a few regression introduced, Ben and Maarten finally
tracked down the one that was causing problems on my MacBookPro, also
nvidia gave some info on the an engine we were using incorrectly, so
disable our use of it, and one regresion with pci hotplug affecting
optimus users.
Radeon has an oops fixs, sync fix, and one workaround to avoid broken
functionality on 32-bit x86, this needs better root causing and a
better fix, but the bandaid is a lot safer at this point"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
drm/radeon: sync all BOs involved in a CS v2
nouveau: move the hotplug ignore to correct place.
drm/nouveau/gf116: remove copy1 engine
drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it
1) Fill in ethtool link parameters for all link types in cxgb4, from
Hariprasad Shenai.
2) Fix probe regressions in stmmac driver, from Huacai Chen.
3) Network namespace leaks on errirs in rtnetlink, from Nicolas
Dichtel.
4) Remove erroneous BUG check which can actually trigger legitimately,
in xen-netfront. From Seth Forshee.
5) Validate length of IFLA_BOND_ARP_IP_TARGET netlink attributes, from
Thomas Grag.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
sh_eth: Fix sleeping function called from invalid context
stmmac: platform: Move plat_dat checking earlier
sh_eth: Fix skb alloc size and alignment adjust rule.
rtnetlink: release net refcnt on error in do_setlink()
bond: Check length of IFLA_BOND_ARP_IP_TARGET attributes
Michel Dänzer [Fri, 21 Nov 2014 02:48:57 +0000 (11:48 +0900)]
drm/radeon: Re-show the cursor after a modeset
Setting a mode seems to clear the cursor registers, so we need to
re-program them to make sure the cursor is visible.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Wed, 3 Dec 2014 18:56:12 +0000 (10:56 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull keyring/nfs fixes from James Morris:
"From David Howells:
The first one fixes the handling of maximum buffer size for key
descriptions, fixing the size at 4095 + NUL char rather than whatever
PAGE_SIZE happens to be and permits you to read back the full
description without it getting clipped because some extra information
got prepended.
The second and third fix a bug in NFS idmapper handling whereby a key
representing a mapping between an id and a name expires and causing
EKEYEXPIRED to be seen internally in NFS (which prevents the mapping
from happening) rather than re-looking up the mapping"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: request_key() should reget expired keys rather than give EKEYEXPIRED
KEYS: Simplify KEYRING_SEARCH_{NO,DO}_STATE_CHECK flags
KEYS: Fix the size of the key description passed to/from userspace
Linus Torvalds [Wed, 3 Dec 2014 17:36:20 +0000 (09:36 -0800)]
Merge branch 'akpm' (patches from Andrew Morton)
Merge misc fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
Paul Mackerras [Tue, 2 Dec 2014 23:59:48 +0000 (15:59 -0800)]
slab: fix nodeid bounds check for non-contiguous node IDs
The bounds check for nodeid in ____cache_alloc_node gives false
positives on machines where the node IDs are not contiguous, leading to
a panic at boot time. For example, on a POWER8 machine the node IDs are
typically 0, 1, 16 and 17. This means that num_online_nodes() returns
4, so when ____cache_alloc_node is called with nodeid = 16 the VM_BUG_ON
triggers, like this:
To fix this, we instead compare the nodeid with MAX_NUMNODES, and
additionally make sure it isn't negative (since nodeid is an int). The
check is there mainly to protect the array dereference in the get_node()
call in the next line, and the array being dereferenced is of size
MAX_NUMNODES. If the nodeid is in range but invalid (for example if the
node is off-line), the BUG_ON in the next line will catch that.
Fixes: 14e50c6a9bc2 ("mm: slab: Verify the nodeid passed to ____cache_alloc_node") Signed-off-by: Paul Mackerras <paulus@samba.org> Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Reviewed-by: Pekka Enberg <penberg@kernel.org> Acked-by: David Rientjes <rientjes@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Forrest [Tue, 2 Dec 2014 23:59:42 +0000 (15:59 -0800)]
mm: fix anon_vma_clone() error treatment
Andrew Morton noticed that the error return from anon_vma_clone() was
being dropped and replaced with -ENOMEM (which is not itself a bug
because the only error return value from anon_vma_clone() is -ENOMEM).
I did an audit of callers of anon_vma_clone() and discovered an actual
bug where the error return was being lost. In __split_vma(), between
Linux 3.11 and 3.12 the code was changed so the err variable is used
before the call to anon_vma_clone() and the default initial value of
-ENOMEM is overwritten. So a failure of anon_vma_clone() will return
success since err at this point is now zero.
Below is a patch which fixes this bug and also propagates the error
return value from anon_vma_clone() in all cases.
Fixes: ef0855d334e1 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()") Signed-off-by: Daniel Forrest <dan.forrest@ssec.wisc.edu> Reviewed-by: Michal Hocko <mhocko@suse.cz> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Tim Hartrick <tim@edgecast.com> Cc: Hugh Dickins <hughd@google.com> Cc: Michel Lespinasse <walken@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> [3.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Tue, 2 Dec 2014 23:59:39 +0000 (15:59 -0800)]
mm: fix swapoff hang after page migration and fork
I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.
I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.
Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so. Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.
There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.
Manfred Spraul [Tue, 2 Dec 2014 23:59:34 +0000 (15:59 -0800)]
ipc/sem.c: fully initialize sem_array before making it visible
ipc_addid() makes a new ipc identifier visible to everyone. New objects
start as locked, so that the caller can complete the initialization
after the call. Within struct sem_array, at least sma->sem_base and
sma->sem_nsems are accessed without any locks, therefore this approach
doesn't work.
Thus: Move the ipc_addid() to the end of the initialization.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com> Reported-by: Rik van Riel <riel@redhat.com> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Davidlohr Bueso <dave@stgolabs.net> Acked-by: Rafael Aquini <aquini@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thierry Reding [Wed, 3 Dec 2014 15:52:18 +0000 (16:52 +0100)]
drm/edid: Restore kerneldoc consistency
Commit 18df89fef2d5 ("drm: Decouple EDID parsing from I2C adapter")
renamed the adapter parameter of the drm_do_probe_ddc_edid function
to data but didn't update the kerneldoc accordingly.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>