Manish Chopra [Thu, 2 Jan 2014 18:38:43 +0000 (13:38 -0500)]
qlcnic: Fix loopback diagnostic test
o Adapter requires that if the port is in loopback mode no traffic should
be flowing through that port, so on arrival of Link up AEN, do not advertise
Link up to the stack until port is out of loopback mode
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
... but the order in which the side effects take place is
undefined because there is no intervening sequence point.
As llc_sk(sk)->vR is written in llc_sk(sk)->vR (assignment
left-hand side) and written in ++llc_sk(sk)->vR & 0xffffffffffffff7f
this might possibly yield undefined behavior.
The final value of llc_sk(sk)->vR is ambiguous, because,
depending on the order of expression evaluation, the
increment may occur before, after, or interleaved with
the assignment. In C, evaluating such an expression yields
undefined behavior.
Since we're doing the increment via PDU_GET_NEXT_Vr() macro
and the only place it is being used is from
llc_conn_ac_inc_vr_by_1(), in order to increment vR by 1
with a follow-up optimized modulo, rewrite the expression
into ((vR + 1) & CONST) in order to fix this.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 1 Jan 2014 09:06:45 +0000 (11:06 +0200)]
bnx2x: Fix KR2 work-around detection of BCM8073
KR2 work-around is based on detecting non-KR2 devices which may not link up
in this mode. One such link-partner is the BCM8073 which has specific
advertisement characteristics in specific mode, and this condition was not set
correctly.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 1 Jan 2014 09:06:44 +0000 (11:06 +0200)]
bnx2x: Fix incorrect link-up report
Fix a problem where link is reported to be up when SFP+ module is plugged in
without cable. This occurs with specific module types which may generate
temporary TX_FAULT indication. Solution is to avoid changing any link parameters
when checking TX_FAULT indication while physical link is down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 1 Jan 2014 09:06:43 +0000 (11:06 +0200)]
bnx2x: Fix Duplex setting for 54618se
BCM54618SE is used to advertise half-duplex even if HD was not requested by the
user. This change makes the legacy speed/duplex advertisement for this PHY
exactly according to the requested speed and duplex.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 1 Jan 2014 09:06:42 +0000 (11:06 +0200)]
bnx2x: Fix passive DAC cable detection
Fix Passive DAC detection for specific cables, such that even in case
SFP_CABLE_TECHNOLOGY option is not set in the EEPROM (offset 8), treat it as a
passive DAC cable, since some cables don't have this indication.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 1 Jan 2014 09:06:41 +0000 (11:06 +0200)]
bnx2x: Fix 578xx-KR 1G link
Fix a problem where 578xx-KR is unable to get link when connected to 1G link
partner. Two fixes were required:
One was to force CL37 sync_status low to prevent Warpcore from getting stuck in
CL73 parallel detect loop while link partner is sending.
Second fix was to enable auto-detect mode, thus allowing the Warpcore to select
the higher speed protocol between 10G-KR (over CL73), or go down to 1G over CL73
when there's indication for it.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Octavian Purdila [Mon, 23 Dec 2013 17:06:31 +0000 (19:06 +0200)]
usbnet: mcs7830: rework link state detection
Even with the quirks in commit dabdaf0c (mcs7830: Fix link state
detection) there are still spurious link-down events for some chips
where the false link-down events count go over a few hundreds.
This patch takes a more conservative approach and only looks at
link-down events where the link-down state is not combined with other
states (e.g. half/full speed, pending frames in SRAM or TX status
information valid). In all other cases we assume the link is up.
Tested on MCS7830CV-DA (USB ID 9710:7830).
Cc: Ondrej Zary <linux@rainbow-software.org> Cc: Michael Leun <lkml20120218@newton.leun.net> Cc: Ming Lei <ming.lei@canonical.com> Signed-off-by: Octavian Purdila <octavian.purdila@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 31 Dec 2013 21:23:35 +0000 (16:23 -0500)]
vlan: Fix header ops passthru when doing TX VLAN offload.
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 30 Dec 2013 18:22:57 +0000 (10:22 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"A bit more endian problems found during testing of 3.13 and a few
other simple fixes and regressions fixes"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix alignment of secondary cpu spin vars
powerpc: Align p_end
powernv/eeh: Add buffer for P7IOC hub error data
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
powerpc: Make unaligned accesses endian-safe for powerpc
powerpc: Fix bad stack check in exception entry
powerpc/512x: dts: disable MPC5125 usb module
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node (5125)
Pull networking fixes from David Miller:
"Some holiday bug fixes for 3.13... There is still one bug I'd like to
get fixed before 3.13-final.
The vlan code erroneously assignes the header ops of the underlying
real device to the VLAN device above it when the real device can
hardware offload VLAN handling. That's completely bogus because
header ops are tied to the device type, so they only expect to see a
'dev' argument compatible with their ops.
The fix is the have the VLAN code use a special set of header ops that
does the pass-thru correctly, by calling the underlying real device's
header ops but _also_ passing in the real device instead of the VLAN
device.
That fix is currently waiting some testing.
Anyways, of note here:
1) Fix bitmap edge case in radiotap, from Johannes Berg.
2) Fix oops on driver unload in rtlwifi, from Larry Finger.
3) Bonding doesn't do locking correctly during speed/duplex/link
changes, from Ding Tianhong.
4) Fix header parsing in GRE code, this bug has been around for a few
releases. From Timo Teräs.
5) SIT tunnel driver MTU check needs to take GSO into account, from
Eric Dumazet.
6) Minor info leak in inet_diag, from Daniel Borkmann.
7) Info leak in YAM hamradio driver, from Salva Peiró.
8) Fix route expiration state handling in ipv6 routing code, from Li
RongQing.
9) DCCP probe module does not check request_module()'s return value,
from Wang Weidong.
10) cpsw driver passes NULL device names to request_irq(), from
Mugunthan V N.
11) Prevent a NULL splat in RDS binding code, from Sasha Levin.
12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.
13) Cure use after free in arc_emac and fec driver's software
timestamp handling, from Eric Dumazet.
14) SIT driver can fail to release the route when
iptunnel_handle_offloads() throws an error. From Li RongQing.
15) Several batman-adv fixes from Simon Wunderlich and Antonio
Quartulli.
16) Fix deadlock during TIPC socket release, from Ying Xue.
17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
Florian Westphal.
18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
stmmac: Fix incorrect spinlock release and PTP cap detection.
phy: IRQ cannot be shared
net: rose: restore old recvmsg behavior
xen-netback: fix guest-receive-side array sizes
fec: Do not assume that PHY reset is active low
tipc: fix deadlock during socket release
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
batman-adv: fix vlan header access
batman-adv: clean nf state when removing protocol header
batman-adv: fix alignment for batadv_tvlv_tt_change
batman-adv: fix size of batadv_bla_claim_dst
batman-adv: fix size of batadv_icmp_header
batman-adv: fix header alignment by unrolling batadv_header
batman-adv: fix alignment for batadv_coded_packet
netfilter: nf_tables: fix oops when updating table with user chains
netfilter: nf_tables: fix dumping with large number of sets
ipv6: release dst properly in ipip6_tunnel_xmit
netxen: Correct off-by-one errors in bounds checks
net: Add some clarification to skb_tx_timestamp() comment.
arc_emac: fix potential use after free
...
This patch adjusts the refcount in the walk of the interrupt tree.
When a match is found, there is no need to increase the refcount
on 'out_irq->np' as 'newpar' is already holding a ref. The refcount
balance between 'ipar' and 'newpar' is maintained in the skiplevel:
goto label.
This patch also removes the usage of the device_node variable 'old'
which seems useless after the latest changes.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com> Signed-off-by: Rob Herring <robh@kernel.org>
Nikita Yushchenko reports:
While trying to make freescale p2020ds and mpc8572ds boards working
with mainline kernel, I faced that commit e38c0a1f (Handle
Both these boards have uli1575 chip.
Corresponding part in device tree is something like
With commit e38c0a1f reverted, devices under uli1575 are registered
correctly, e.g. for rtc
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 0000000100000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 010000000000000000000000
OF: with offset: 70
OF: one level translation: 000000000000000000000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: parent translation for: 010000000000000000000000
OF: with offset: 70
OF: one level translation: 010000000000000000000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 010000000000000000000000
OF: with offset: 70
OF: one level translation: 010000000000000000000070
OF: parent bus is default (na=2, ns=2) on /
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 00000000ffc10000
OF: with offset: 70
OF: one level translation: 00000000ffc10070
OF: reached root node
With commit e38c0a1f in place, address translation fails:
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 0000000100000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 010000000000000000000000
OF: with offset: 70
OF: one level translation: 000000000000000000000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: not found !
Thierry Reding confirmed this commit was not needed after all:
"We ended up merging a different address representation for Tegra PCIe
and I've confirmed that reverting this commit doesn't cause any obvious
regressions. I think all other drivers in drivers/pci/host ended up
copying what we did on Tegra, so I wouldn't expect any other breakage
either."
There doesn't appear to be a simple way to support both behaviours, so
reverting this as nothing should be depending on the new behaviour.
Cc: stable@vger.kernel.org # v3.7+ Signed-off-by: Rob Herring <robh@kernel.org>
Vince Bridgers [Fri, 20 Dec 2013 17:19:34 +0000 (11:19 -0600)]
stmmac: Fix incorrect spinlock release and PTP cap detection.
This patch corrects a problem in stmmac_ptp.c, functions
stmmac_adjust_time and stmmac_adjust_freq where the incorrect spinlocks
were released. This patch also addresses a problem in stmmac_main,
function stmmac_init_ptp where the capability detection for
advanced timestamping was masked by message masking.
This patch was touch tested using linuxptp, and runs without the previously
observed instabilities. More extensive testing is ongoing.
Vince
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Fri, 20 Dec 2013 19:09:04 +0000 (22:09 +0300)]
phy: IRQ cannot be shared
With the way PHY IRQ handler is implemented (all real handling being pushed to
the workqueue and returning IRQ_HANDLED all the time PHY is active), we cannot
really claim that PHY IRQ can be shared when calling request_irq().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Sun, 22 Dec 2013 23:32:31 +0000 (00:32 +0100)]
net: rose: restore old recvmsg behavior
recvmsg handler in net/rose/af_rose.c performs size-check ->msg_namelen.
After commit f3d3342602f8bcbf37d7c46641cb9bca7618eb1c
(net: rework recvmsg handler msg_name and msg_namelen logic), we now
always take the else branch due to namelen being initialized to 0.
Digging in netdev-vger-cvs git repo shows that msg_namelen was
initialized with a fixed-size since at least 1995, so the else branch
was never taken.
Compile tested only.
Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Mon, 23 Dec 2013 09:27:17 +0000 (09:27 +0000)]
xen-netback: fix guest-receive-side array sizes
The sizes chosen for the metadata and grant_copy_op arrays on the guest
receive size are wrong;
- The meta array is needlessly twice the ring size, when we only ever
consume a single array element per RX ring slot
- The grant_copy_op array is way too small. It's sized based on a bogus
assumption: that at most two copy ops will be used per ring slot. This
may have been true at some point in the past but it's clear from looking
at start_new_rx_buffer() that a new ring slot is only consumed if a frag
would overflow the current slot (plus some other conditions) so the actual
limit is MAX_SKB_FRAGS grant_copy_ops per ring slot.
This patch fixes those two sizing issues and, because grant_copy_ops grows
so much, it pulls it out into a separate chunk of vmalloc()ed memory.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: David Vrabel <david.vrabel@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Tue, 24 Dec 2013 14:16:01 +0000 (12:16 -0200)]
fec: Do not assume that PHY reset is active low
We should not assume that the PHY reset is always active low.
Retrieve this information from the device tree instead, so that the PHY reset
can work on both cases.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The opposite order of holding port lock and node lock on above two
different paths may result in a deadlock. If socket lock instead of
port lock is used to protect port instance in tipc_withdraw(), the
reverse order of holding port lock and node lock will be eliminated,
as a result, the deadlock is killed as well.
Reported-by: Lars Everbrand <lars.everbrand@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Sat, 28 Dec 2013 21:01:47 +0000 (13:01 -0800)]
powerpc: Fix alignment of secondary cpu spin vars
Commit 5c0484e25ec0 ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.
This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.
Fix is to add explicit alignment instead of relying on good luck. :)
[ It appears that there is a different issue with PA Semi systems
however this fix is definitely correct so applying anyway -- BenH
]
Fixes: 5c0484e25ec0 ('powerpc: Endian safe trampoline') Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811 Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Mon, 23 Dec 2013 01:19:51 +0000 (12:19 +1100)]
powerpc: Align p_end
p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.
This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Fri, 20 Dec 2013 19:06:01 +0000 (13:06 -0600)]
powernv/eeh: Add buffer for P7IOC hub error data
Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data. Take care to inform OPAL of
the correct size for the buffer.
[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com> Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Thu, 19 Dec 2013 23:14:07 +0000 (17:14 -0600)]
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com> Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul E. McKenney [Tue, 17 Dec 2013 22:29:57 +0000 (09:29 +1100)]
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
The powerpc 64-bit __copy_tofrom_user() function uses shifts to handle
unaligned invocations. However, these shifts were designed for
big-endian systems: On little-endian systems, they must shift in the
opposite direction.
This commit relies on the C preprocessor to insert the correct shifts
into the assembly code.
[ This is a rare but nasty LE issue. Most of the time we use the POWER7
optimised __copy_tofrom_user_power7 loop, but when it hits an exception
we fall back to the base __copy_tofrom_user loop. - Anton ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Make unaligned accesses endian-safe for powerpc
The generic put_unaligned/get_unaligned macros were made endian-safe by
calling the appropriate endian dependent macros based on the endian type
of the powerpc processor.
Signed-off-by: Rajesh B Prathipati <rprathip@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 16 Dec 2013 04:12:43 +0000 (15:12 +1100)]
powerpc: Fix bad stack check in exception entry
In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel. If it's not valid, we die but
with a nice oops message.
Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative. Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.
This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE. With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.
Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Sun, 29 Dec 2013 21:49:51 +0000 (13:49 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another smallish batch of fixes, it's been quiet due to the holidays.
Nothing controversial here, a handful of things across the board"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix USB gadget driver compilation regression
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Linus Torvalds [Sun, 29 Dec 2013 21:35:04 +0000 (13:35 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"There is a small EFI fix and a big power regression fix in this batch.
My queue also had a fix for downing a CPU when there are insufficient
number of IRQ vectors available, but I'm holding that one for now due
to recent bug reports"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't select EFI from certain special ACPI drivers
x86 idle: Repair large-server 50-watt idle-power regression
Linus Torvalds [Sun, 29 Dec 2013 21:27:51 +0000 (13:27 -0800)]
Merge tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver from
Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: add support for ValleyView Soc
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
David S. Miller [Sun, 29 Dec 2013 05:30:59 +0000 (00:30 -0500)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- reset netfilter-bridge state when removing the batman-adv
header from an incoming packet. This prevents netfilter
bridge from being fooled when the same packet enters a
bridge twice (or more): the first time within the
batman-adv header and the second time without.
- adjust the packet layout to prevent any architecture from
adding padding bytes. All the structs sent over the wire
now have size multiple of 4bytes (unless pack(2) is used).
- fix access to the inner vlan_eth header when reading the
VID in the rx path.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 29 Dec 2013 05:24:28 +0000 (00:24 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
This patchset contains four nf_tables fixes, one IPVS fix due to
missing updates in the interaction with the new sedadj conntrack
extension that was added to support the netfilter synproxy code,
and a couple of one-liners to fix netnamespace netfilter issues.
More specifically, they are:
* Fix ipv6_find_hdr() call without offset being explicitly initialized
in nft_exthdr, as required by that function, from Daniel Borkmann.
* Fix oops in nfnetlink_log when using netns and unloading the kernel
module, from Gao feng.
* Fix BUG_ON in nf_ct_timestamp extension after netns is destroyed,
from Helmut Schaa.
* Fix crash in IPVS due to missing sequence adjustment extension being
allocated in the conntrack, from Jesper Dangaard Brouer.
* Add bugtrap to spot a warning in case you deference sequence adjustment
conntrack area when not available, this should help to catch similar
invalid dereferences in the Netfilter tree, also from Jesper.
* Fix incomplete dumping of sets in nf_tables when retrieving by family,
from me.
* Fix oops when updating the table state (dormant <-> active) and having
user (not base ) chains, from me.
* Fix wrong validation in set element data that results in returning
-EINVAL when using the nf_tables dictionary feature with mappings,
also from me.
We don't usually have this amount of fixes by this time (as we're already
in -rc5 of the development cycle), although half of them are related to
nf_tables which is a relatively new thing, and I also believe that holidays
have also delayed the flight of bugfixes to mainstream a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Sat, 28 Dec 2013 23:38:32 +0000 (15:38 -0800)]
Merge tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
+ v3.13-rc5
Olof Johansson [Sat, 28 Dec 2013 23:20:35 +0000 (15:20 -0800)]
Merge tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by 8c9b1aa41853272a ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071b3d23f
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16eb8f0d0
("pwm-backlight: Add power supply support") in v3.12.
* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Wed, 11 Dec 2013 08:48:58 +0000 (09:48 +0100)]
ARM: pxa: fix USB gadget driver compilation regression
After commit 88f718e3fa4d67f3a8dbe79a2f97d722323e4051
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab1ef130e8bf30bcd3e529b7f35112c503
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.
However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:
This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.
Before commit 88f718e3fa4d67f3a8dbe79a2f97d722323e4051
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.
Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
This patch fixes dictionary mappings, eg.
add rule ip filter input meta dnat set tcp dport map { 22 => 1.1.1.1, 23 => 2.2.2.2 }
The kernel was returning -EINVAL in nft_validate_data_load() since
the type of the set element data that is passed was the real userspace
datatype instead of NFT_DATA_VALUE.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
batman-adv: clean nf state when removing protocol header
If an interface enslaved into batman-adv is a bridge (or a
virtual interface built on top of a bridge) the nf_bridge
member of the skbs reaching the soft-interface is filled
with the state about "netfilter bridge" operations.
Then, if one of such skbs is locally delivered, the nf_bridge
member should be cleaned up to avoid that the old state
could mess up with other "netfilter bridge" operations when
entering a second bridge.
This is needed because batman-adv is an encapsulation
protocol.
However at the moment skb->nf_bridge is not released at all
leading to bogus "netfilter bridge" behaviours.
Fix this by cleaning the netfilter state of the skb before
it gets delivered to the upper layer in interface_rx().
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Since this is a mac address and always 48 bit, and we can assume that
it is always aligned to 2-byte boundaries, add a pack(2) pragma.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
struct batadv_icmp_header currently has a size of 17, which
will be padded to 20 on some architectures. Fix this by
unrolling the header into the parent structures.
Moreover keep the ICMP parsing functions as generic as they
are now by using a stub icmp_header struct during packet
parsing.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
batman-adv: fix header alignment by unrolling batadv_header
The size of the batadv_header of 3 is problematic on some architectures
which automatically pad all structures to a 32 bit boundary. To not lose
performance by packing this struct, better embed it into the various
host structures.
Reported-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The compiler may decide to pad the structure, and then it does not
have the expected size of 46 byte. Fix this by moving it in the
pragma pack(2) part of the code.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
netfilter: nf_tables: fix dumping with large number of sets
If not table name is specified, the dumping of the existing sets
may be incomplete with a sufficiently large number of sets and
tables. This patch fixes missing reset of the cursors after
finding the location of the last object that has been included
in the previous multi-part message.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Li RongQing [Fri, 20 Dec 2013 09:20:12 +0000 (17:20 +0800)]
ipv6: release dst properly in ipip6_tunnel_xmit
if a dst is not attached to anywhere, it should be released before
exit ipip6_tunnel_xmit, otherwise cause dst memory leakage.
Fixes: 61c1db7fae21 ("ipv6: sit: add GSO/TSO support") Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Gibson [Fri, 20 Dec 2013 04:10:44 +0000 (15:10 +1100)]
netxen: Correct off-by-one errors in bounds checks
netxen_process_lro() contains two bounds checks. One for the ring number
against the number of rings, and one for the Rx buffer ID against the
array of receive buffers.
Both of these have off-by-one errors, using > instead of >=. The correct
versions are used in netxen_process_rcv(), they're just wrong in
netxen_process_lro().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Dec 2013 18:04:33 +0000 (13:04 -0500)]
net: Add some clarification to skb_tx_timestamp() comment.
We've seen so many instances of people invoking skb_tx_timestamp()
after the device already has been given the packet, that it's worth
being a little bit more verbose and explicit in this comment.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 20 Dec 2013 02:10:40 +0000 (18:10 -0800)]
arc_emac: fix potential use after free
Signed-off-by: Eric Dumazet <edumazet@google.com>
skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.
Fixes: e4f2379db6c6 ("ethernet/arc/arc_emac - Add new driver")
From: Eric Dumazet <edumazet@google.com> Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nithin Sujir [Fri, 20 Dec 2013 01:44:11 +0000 (17:44 -0800)]
tg3: Expand 4g_overflow_test workaround to skb fragments of any size.
The current driver assumes that an skb fragment can only be upto jumbo
size. Presumably this was a fast-path optimization. This assumption is
no longer true as fragments can be upto 32k.
v2: Remove unnecessary parantheses per Eric Dumazet.
Cc: stable@vger.kernel.org Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Fri, 27 Dec 2013 17:51:25 +0000 (09:51 -0800)]
Merge tag 'for-v3.13-rc/hwmod-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
Jamal Hadi Salim [Mon, 23 Dec 2013 13:02:11 +0000 (08:02 -0500)]
net_sched: act: Dont increment refcnt on replace
This is a bug fix. The existing code tries to kill many
birds with one stone: Handling binding of actions to
filters, new actions and replacing of action
attributes. A simple test case to illustrate:
XXXX
moja@fe1:~$ sudo tc actions add action drop index 12
moja@fe1:~$ actions get action gact index 12
action order 1: gact action drop
random type none pass val 0
index 12 ref 1 bind 0
moja@fe1:~$ sudo tc actions replace action ok index 12
moja@fe1:~$ actions get action gact index 12
action order 1: gact action drop
random type none pass val 0
index 12 ref 2 bind 0
XXXX
The above shows the refcounf being wrongly incremented on replace.
There are more complex scenarios with binding of actions to filters
that i am leaving out that didnt work as well...
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8bed3e1 (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.
Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments] Signed-off-by: Tony Lindgren <tony@atomide.com>
ipvs: correct usage/allocation of seqadj ext in ipvs
The IPVS FTP helper ip_vs_ftp could trigger an OOPS in nf_ct_seqadj_set,
after commit 41d73ec053d2 (netfilter: nf_conntrack: make sequence number
adjustments usuable without NAT).
This is because, the seqadj ext is now allocated dynamically, and the
IPVS code didn't handle this situation. Fix this in the IPVS nfct
code by invoking the alloc function nfct_seqadj_ext_add().
Fixes: 41d73ec053d2 (netfilter: nf_conntrack: make sequence number adjustments usuable without NAT) Suggested-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au>
netfilter: WARN about wrong usage of sequence number adjustments
Since commit 41d73ec053d2 (netfilter: nf_conntrack: make sequence
number adjustments usuable without NAT), the sequence number extension
is dynamically allocated.
Instead of dying, give a WARN splash, in case of wrong usage of the
seqadj code, e.g. when forgetting to allocate via nfct_seqadj_ext_add().
Merge branches 'pm-cpufreq' and 'pm-sleep' containing PM fixes
* pm-cpufreq:
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
* pm-sleep:
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
Florian Westphal [Thu, 26 Dec 2013 11:17:00 +0000 (12:17 +0100)]
macvlan: fix netdev feature propagation from lower device
There are inconsistencies wrt. feature propagation/inheritance between
macvlan and the underlying interface.
When a feature is turned off on the real device before a macvlan is
created on top, these will remain enabled on the macvlan device, whereas
turning off the feature on the lower device after macvlan creation the
kernel will propagate the changes to the macvlan.
The second issue is that, when propagating changes from underlying device
to the macvlan interface, macvlan can erronously lose its NETIF_F_LLTX flag,
as features are anded with the underlying device.
However, LLTX should be kept since it has no dependencies on physical
hardware (LLTX is set on macvlan creation regardless of the lower
device properties, see 8ffab51b3dfc54876f145f15b351c41f3f703195
(macvlan: lockless tx path).
The LLTX flag is now forced regardless of user settings in absence of
layer2 hw acceleration (a6cc0cfa72e0b6d9f2c8fd858aa,
net: Add layer 2 hardware acceleration operations for macvlan devices).
Use netdev_increment_features to rebuild the feature set on capability
changes on either the lower device or on the macvlan interface.
As pointed out by Ben Hutchings, use netdev_update_features on
NETDEV_FEAT_CHANGE event (it calls macvlan_fix_features/netdev_features_change
if needed).
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 26 Dec 2013 17:26:12 +0000 (09:26 -0800)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A collection of bug fixes destined for stable and some printk cleanups
and a patch so that instead of BUG'ing we use the ext4_error()
framework to mark the file system is corrupted"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: add explicit casts when masking cluster sizes
ext4: fix deadlock when writing in ENOSPC conditions
jbd2: rename obsoleted msg JBD->JBD2
jbd2: revise KERN_EMERG error messages
jbd2: don't BUG but return ENOSPC if a handle runs out of space
ext4: Do not reserve clusters when fs doesn't support extents
ext4: fix del_timer() misuse for ->s_err_report
ext4: check for overlapping extents in ext4_valid_extent_entries()
ext4: fix use-after-free in ext4_mb_new_blocks
ext4: call ext4_error_inode() if jbd2_journal_dirty_metadata() fails
Suman Anna [Mon, 23 Dec 2013 22:53:11 +0000 (16:53 -0600)]
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit ec2c082 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).
Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
OMAP2 - GPMC, RNG
OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: Suman Anna <s-anna@ti.com> Fixes: 7d7e1eba7e92 ("ARM: OMAP2+: Prepare for irqs.h removal") Fixes: ec2c0825ca31 ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ") Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Thu, 12 Dec 2013 09:52:49 +0000 (15:22 +0530)]
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
With commit '7dedd34: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.
On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> # on a different base Signed-off-by: Rajendra Nayak <rnayak@ti.com> Fixes: 7dedd346941d ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL") Signed-off-by: Paul Walmsley <paul@pwsan.com>
Linus Torvalds [Tue, 24 Dec 2013 18:06:03 +0000 (10:06 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- fix for a memory leak on certain unplug events
- a collection of bcache fixes from Kent and Nicolas
- a few null_blk fixes and updates form Matias
- a marking of static of functions in the stec pci-e driver
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: support submit_queues on use_per_node_hctx
null_blk: set use_per_node_hctx param to false
null_blk: corrections to documentation
null_blk: warning on ignored submit_queues param
null_blk: refactor init and init errors code paths
null_blk: documentation
null_blk: mem garbage on NUMA systems during init
drivers: block: Mark the functions as static in skd_main.c
bcache: New writeback PD controller
bcache: bugfix for race between moving_gc and bucket_invalidate
bcache: fix for gc and writeback race
bcache: bugfix - moving_gc now moves only correct buckets
bcache: fix for gc crashing when no sectors are used
bcache: Fix heap_peek() macro
bcache: Fix for can_attach_cache()
bcache: Fix dirty_data accounting
bcache: Use uninterruptible sleep in writeback
bcache: kthread don't set writeback task to INTERUPTIBLE
block: fix memory leaks on unplugging block device
bcache: fix sparse non static symbol warning
Linus Torvalds [Tue, 24 Dec 2013 17:49:20 +0000 (09:49 -0800)]
Merge branch 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Two fixes. One fixes a bug in the error path of cgroup_create(). The
other changes cgrp->id lifetime rule so that the id doesn't get
recycled before all controller states are destroyed. This premature
id recycling made memcg malfunction"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: don't recycle cgroup id until all csses' have been destroyed
cgroup: fix cgroup_create() error handling path
Linus Torvalds [Tue, 24 Dec 2013 17:48:43 +0000 (09:48 -0800)]
Merge branch 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fix from Tejun Heo:
"A single commit to fix a spurious sparse warning coming from
DEFINE_PER_CPU()'s hack to support the use of weak symbols. Shouldn't
cause observable behavior change"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix spurious sparse warnings from DEFINE_PER_CPU()
Linus Torvalds [Tue, 24 Dec 2013 17:35:58 +0000 (09:35 -0800)]
Merge branch 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"There's one interseting commit - "libata, freezer: avoid block device
removal while system is frozen". It's an ugly hack working around a
deadlock condition between driver core resume and block layer device
removal paths through freezer which was made more reproducible by
writeback being converted to workqueue some releases ago. The bug has
nothing to do with libata but it's just an workaround which is easy to
backport. After discussion, Rafael and I seem to agree that we don't
really need kernel freezables - both kthread and workqueue. There are
few specific workqueues which constitute PM operations and require
freezing, which will be converted to use workqueue_set_max_active()
instead. All other kernel freezer uses are planned to be removed,
followed by the removal of kthread and workqueue freezer support,
hopefully.
Others are device-specific fixes. The most notable is the addition of
NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
M500 SSDs which otherwise suffers data corruption"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata, freezer: avoid block device removal while system is frozen
libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
libata: disable a disk via libata.force params
ahci: bail out on ICH6 before using AHCI BAR
ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8
Ard Biesheuvel [Mon, 23 Dec 2013 17:49:30 +0000 (18:49 +0100)]
auxvec.h: account for AT_HWCAP2 in AT_VECTOR_SIZE_BASE
Commit 2171364d1a92 ("powerpc: Add HWCAP2 aux entry") introduced a new
AT_ auxv entry type AT_HWCAP2 but failed to update AT_VECTOR_SIZE_BASE
accordingly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Fixes: 2171364d1a92 (powerpc: Add HWCAP2 aux entry) Cc: stable@vger.kernel.org Acked-by: Michael Neuling <michael@neuling.org> Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 24 Dec 2013 01:23:42 +0000 (17:23 -0800)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Last batch of InfiniBand/RDMA changes for 3.13 / 2014:
- Additional checks for uverbs to ensure forward compatibility,
handle malformed input better.
- Fix potential use-after-free in iWARP connection manager.
- Make a function static"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Check access to userspace response buffer in extended command
IB/uverbs: Check input length in flow steering uverbs
IB/uverbs: Set error code when fail to consume all flow_spec items
IB/uverbs: Check reserved fields in create_flow
IB/uverbs: Check comp_mask in destroy_flow
IB/uverbs: Check reserved field in extended command header
IB/uverbs: New macro to set pointers to NULL if length is 0 in INIT_UDATA()
IB/core: const'ify inbuf in struct ib_udata
RDMA/iwcm: Don't touch cm_id after deref in rem_ref
RDMA/cxgb4: Make _c4iw_write_mem_dma() static
selinux_setprocattr() does ptrace_parent(p) under task_lock(p),
but task_struct->alloc_lock doesn't pin ->parent or ->ptrace,
this looks confusing and triggers the "suspicious RCU usage"
warning because ptrace_parent() does rcu_dereference_check().
And in theory this is wrong, spin_lock()->preempt_disable()
doesn't necessarily imply rcu_read_lock() we need to access
the ->parent.
Reported-by: Evan McNabb <emcnabb@redhat.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Paul Moore <pmoore@redhat.com>
Linus Torvalds [Mon, 23 Dec 2013 19:49:16 +0000 (11:49 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Xmas fixes pull, all small nothing major, intel, radeon, one ttm
regression, and one build fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: Fix swapin regression
gpu: fix qxl missing crc32_le
drm/radeon: fix asic gfx values for scrapper asics
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
Linus Torvalds [Mon, 23 Dec 2013 18:49:44 +0000 (10:49 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio balloon driver fixes from Rusty Russell:
"Refactoring broke the balloon driver, and fixing kallsyms on ARM broke
some (non-ARM) MMUless setups, so we're making that fix ARM-only for
now.
Unfortunately, the ARM refactoring which broke kallsyms/perf was
CC:stable, so the fix (which broken non-ARM) was also CC:stable, so
now the partial reversion is also CC:stable..."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
scripts/link-vmlinux.sh: only filter kernel symbols for arm
virtio_balloon: update_balloon_size(): update correct field
Dave Airlie [Mon, 23 Dec 2013 00:35:57 +0000 (10:35 +1000)]
Merge tag 'drm-intel-fixes-2013-12-18' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Besides the 2 fixes for tricky corner cases in gem from Chris I've
promised already two patche from Paulo to fix pc8 warnings (both ported
from -next, bug report from Dave Jones) and one patch from to fix vga
enable/disable on snb+. That one is a really old bug, but apparently it
can cause machine hangs if you try hard enough with vgacon/efifb handover.
* tag 'drm-intel-fixes-2013-12-18' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
Dave Airlie [Mon, 23 Dec 2013 00:34:18 +0000 (10:34 +1000)]
Merge branch 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
- fix for a long standing corruption bug on some Trinity/Richland parts.
- Stability fix for cayman dpm
- audio fixes for dce6+
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix asic gfx values for scrapper asics
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
Thomas Hellstrom [Sat, 21 Dec 2013 21:23:02 +0000 (22:23 +0100)]
drm/ttm: Fix swapin regression
Commit "drm/ttm: Don't move non-existing data" didn't take the
swapped-out corner case into account. This patch corrects that.
Fixes blank screen after attempted suspend / hibernate on vmwgfx.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
ipv4: consistent reporting of pmtu data in case of corking
We report different pmtu values back on the first write and on further
writes on an corked socket.
Also don't include the dst.header_len (respectively exthdrlen) as this
should already be dealt with by the interface mtu of the outgoing
(virtual) interface and policy of that interface should dictate if
fragmentation should happen.
Instead reduce the pmtu data by IP options as we do for IPv6. Make the
same changes for ip_append_data, where we did not care about options or
dst.header_len at all.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Wed, 18 Dec 2013 16:03:50 +0000 (21:33 +0530)]
drivers: net : cpsw: pass proper device name while requesting irq
During checking the interrupts with "cat /proc/interrupts", it is showing
device name as (null), this change was done with commit id aa1a15e2d where
request_irq is changed to devm_request_irq also changing the irq name from
platform device name to net device name, but the net device is not
registered at this point with the network frame work, so devm_request_irq
is called with device name as NULL, by which it is showed as "(null)" in
"cat /proc/interrupts". So this patch changes back irq name to platform
device name itself in devm_request_irq so that the device name shows as
below.
David S. Miller [Sun, 22 Dec 2013 23:09:24 +0000 (18:09 -0500)]
Merge branch 'cxgb4'
Hariprasad Shenai says:
====================
This patch series provides miscelleneous fixes for Chelsio T4/T5 adapters
related to server entries and server filter entries.
Also, fixes a bug in ULD (Upper Level Driver) like iw_cxgb4 where-in it
calculates wrong tuple values
on T5 adapter. So, a new API cxgb4_select_ntuple is exported so as to enable
Upper Lever Drivers like iw_cxgb4 to correctly calculate tuple values.
The patches series is created agains David Miller's 'net' tree.
And includes patches on cxgb4 and iw_cxgb4 driver.
Patch 8/8 (RDMA-cxgb4-Use-cxgb4_select_ntuple-to-correctly-calc.patch)
has a build dependency on Patch 5/8
(cxgb4-Add-API-to-correctly-calculate-tuple-fields.patch).
Also, Patch 6/8 (RDMA-cxgb4-Calculate-the-filter-server-TID-properly.patch) has
a functional
dependency on Patch 3/8 (cxgb4-Assign-filter-server-TIDs-properly.patch)
We would like to request this patch series to get merged via David Miller's
'net' tree.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
V2 changes:
- Removed earlier patch which added sftids_in_use counter. However, the counter
was actually not used anywhere in this patch series.
Thanks to David Miller for spotting this.
We have dropped this patch in V2 and will submit a more complete patch which
uses sftids_in_use counter later on.
- Fixed a 'checkpatch.pl --strict' warning on Patch 5/8
(cxgb4-Add-API-to-correctly-calculate-tuple-fields.patch).
- Removed some un-used #defines from Patch 5/8
(cxgb4-Add-API-to-correctly-calculate-tuple-fields.patch).
====================
Signed-off-by: David S. Miller <davem@davemloft.net> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Kumar Sanghvi [Wed, 18 Dec 2013 11:08:26 +0000 (16:38 +0530)]
RDMA/cxgb4: Use cxgb4_select_ntuple to correctly calculate ntuple fields
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 18 Dec 2013 11:08:25 +0000 (16:38 +0530)]
RDMA/cxgb4: Server filters are supported only for IPv4
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 18 Dec 2013 11:08:24 +0000 (16:38 +0530)]
RDMA/cxgb4: Calculate the filter server TID properly
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 18 Dec 2013 11:08:23 +0000 (16:38 +0530)]
cxgb4: Add API to correctly calculate tuple fields
Adds API cxgb4_select_ntuple so as to enable Upper Level Drivers to correctly
calculate the tuple fields.
Adds constant definitions for TP_VLAN_PRI_MAP for the Compressed
Filter Tuple field widths and structures and uses them.
Also, the CPL Parameters field for T5 is 40 bits so we need to prototype
cxgb4_select_ntuple() to calculate and return u64 values.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 18 Dec 2013 11:08:22 +0000 (16:38 +0530)]
cxgb4: Account for stid entries properly in case of IPv6
IPv6 uses 2 TIDs with CLIP enabled and 4 TIDs without CLIP.
Currently we are incrementing STIDs in use by 1 for both IPv4 and IPv6 which
is wrong.
Further, driver currently does not have interface to query if CLIP is programmed
for particular IPv6 address. So, in this patch we increment/decrement TIDs in use
by 4 for IPv6 assuming absence of CLIP. Such assumption keeps us on safe side and
we don't end up allocating more stids for IPv6 than actually supported.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 18 Dec 2013 11:08:21 +0000 (16:38 +0530)]
cxgb4: Assign filter server TIDs properly
The LE workaround code is incorrectly reusing the TCAM TIDs
(meant for allocation by firmware in case of hash collisions) for filter
servers. This patch assigns the filter server TIDs properly starting from
sftid_base index.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 18 Dec 2013 11:08:20 +0000 (16:38 +0530)]
cxgb4: Include TCP as protocol when creating server filters
We were creating LE Workaround Server Filters without specifying
IPPROTO_TCP (6) in the filters (when F_PROTOCOL is set in TP_VLAN_PRI_MAP).
This meant that UDP packets with matching IP Addresses/Ports would get
caught up in the filter and be delivered to ULDs like iw_cxgb4.
So, include the protocol information in the server filter properly.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 18 Dec 2013 11:08:19 +0000 (16:38 +0530)]
cxgb4: Reserve stid 0 for T4/T5 adapters
When creating offload server entries, an IPv6 passive connection request
can trigger a reply with a null STID, whereas the driver would expect
the reply 'STID to match the value used for the request.
This happens due to h/w limitation on T4 and T5.
This patch ensures that STID 0 is never used if the stid range starts
from zero.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 22 Dec 2013 19:13:02 +0000 (11:13 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Much smaller batch of fixes this week.
Biggest one is a revert of an OMAP display change that removed some
non-DT pinmux code that was still needed for 3.13 to get DSI displays
to work.
There's also a fix that resolves some misdescribed GPIO controller
resources on shmobile. The rest are mostly smaller fixes, a couple of
MAINTAINERS updates, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
MAINTAINERS: Add keystone clock drivers
MAINTAINERS: Add keystone git tree information
ARM: s3c64xx: dt: Fix boot failure due to double clock initialization
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Linus Torvalds [Sun, 22 Dec 2013 19:11:57 +0000 (11:11 -0800)]
Merge tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fixlet from Stefan Richter:
"A one-liner to reenable WRITE SAME over SBP-2 like in v3.8...v3.12.
Buggy targets which could malfunction when being subjected to this
command are already sufficiently protected by a scsi_level check in sd
+ SCSI core"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: sbp2: bring back WRITE SAME support
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor items this time around, the most notable being a FILEIO
backend change to enforce hw_max_sectors based upon the current
block_size to address a bug where large sized I/Os (> 1M) where being
rejected"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
qla2xxx: Fix schedule_delayed_work() for target timeout calculations
iser-target: fix error return code in isert_create_device_ib_res()
iscsi-target: Fix-up all zero data-length CDBs with R/W_BIT set
target: Remove write-only stats fields and lock from struct se_node_acl
iscsi-target: return -EINVAL on oversized configfs parameter
projects / linux-beck.git / log