The suspend()/resume() methods already get the right 'struct device' to get the
driver data from -- there's no need to get to the 'struct platform_device' that
contains that 'struct device' just to call dev_get_drvdata()...
Acked-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Turn both helpers (which are used only during LLDs initialization
time and thus are not performance sensitive) into wrappers around
the new ata_pci_init_one() function, this cuts 20 LOC and saves
~1.1k of the output code size (x86-64):
text data bss dec hex filename
21392 0 19 21411 53a3 drivers/ata/libata-sff.o.before
20256 0 19 20275 4f33 drivers/ata/libata-sff.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata: Make pata_of_platform.c compile again and work on non-PPC platforms
This patch adds missing #includes, makes the driver selectable on
non-PPC OF-enabled platforms and fixes property value accesses to
be correct in Little Endian system.
Cc: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan McGee [Wed, 7 Sep 2011 16:23:21 +0000 (11:23 -0500)]
pata_sis: mark most const data static as well
This pushes timing and other values into preinitialized read-only data
sections rather than being inlined into the code. None of these
functions are called more than a handful of times, so reducing code size
makes sense.
Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan McGee [Wed, 7 Sep 2011 16:23:20 +0000 (11:23 -0500)]
pata_sis: enable MWDMA for UDMA 133 chipset
This ports the timing values over from the old IDE driver into the new
PATA-based one. The comment was lying when it stated the old driver was
not MWDMA capable.
Boot tested on actual hardware using 'libata.force=mwdma2'.
Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan McGee [Wed, 7 Sep 2011 16:23:19 +0000 (11:23 -0500)]
pata_sis: add mode_filter method for certain sis5513 chipsets
This mirrors a very old commit (3160d5416f39da9d9, "sis5513: add
->udma_filter method for chipset_family >= ATA_133") to the old sis5513
IDE driver that prevents certain setups from working.
UDMA6 (ATA/133) is not supported on some chipsets and we need to ensure
this mode is not chosen even if a connected drive supports it. Port this
old patch forward to the new PATA driver to ensure UDMA5 is the highest
mode used if that is what is supported.
Kernel bugzilla #41582.
Reviewed-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan McGee [Wed, 7 Sep 2011 16:23:18 +0000 (11:23 -0500)]
pata_sis: extract a sis_port_base() method
This is similar to the existing sis_old_port_base() method. We do this
same calculation and logic in multiple places (with one more to come in
a future patch), so extracting it into a method makes sense.
Reviewed-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Richard Zhu [Wed, 28 Sep 2011 07:41:54 +0000 (15:41 +0800)]
[libata] ahci_platform: Add the board_ids and pi refer to different features
On imx53 AHCI, soft reset fails with IPMS set when PMP
is enabled but SATA HDD/ODD is connected to SATA port,
do soft reset again to port 0.
So the 'ahci_pmp_retry_srst_ops' is required when imx53
ahci is present.
Signed-off-by: Richard Zhu <richard.zhu@linaro.org> Acked-by: Eric Miao <eric.miao@linaro.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With help from Tejun, the problem is found to be caused by 32bit PIO
mode, so introduce the quirk patch to disable 32bit PIO on SATA piix
for some Sandybridge CPT chipsets.
Seth also tested the patch on all five affected chipsets
(pci device ID: 0x1c00, 0x1c01, 0x1d00, 0x1e00, 0x1e01), and found
the patch does fix the problem.
Tested-by: Heasley, Seth <seth.heasley@intel.com> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Cc: stable@kernel.org
ata_sff_data_xfer[32]() use pad area if the transfer size isn't
multiple of transfer size; however, this area wasn't cleared and
garbage data in pad area could be transferred to the device. Make
sure the pad area is cleared.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Lei Ming <tom.leiming@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sergei Shtylyov [Fri, 7 Oct 2011 15:24:22 +0000 (19:24 +0400)]
sata_mv: use {platform|pci}_get_drvdata()
The driver uses dev_get_drvdata() to get to the driver data for the
platform and PCI devices, while the corresponding wrappers exists for
them -- in one case it even declares an otherwise unneeded variable
to do that. Switch to using the {platform|pci}_get_drvdata() instead.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Thu, 6 Oct 2011 23:15:10 +0000 (16:15 -0700)]
Merge git://github.com/davem330/net
* git://github.com/davem330/net:
net: fix typos in Documentation/networking/scaling.txt
bridge: leave carrier on for empty bridge
netfilter: Use proper rwlock init function
tcp: properly update lost_cnt_hint during shifting
tcp: properly handle md5sig_pool references
macvlan/macvtap: Fix unicast between macvtap interfaces in bridge mode
Paul Menzel [Wed, 31 Aug 2011 15:07:10 +0000 (17:07 +0200)]
x86/PCI: use host bridge _CRS info on ASUS M2V-MX SE
In summary, this DMI quirk uses the _CRS info by default for the ASUS
M2V-MX SE by turning on `pci=use_crs` and is similar to the quirk
added by commit 2491762cfb47 ("x86/PCI: use host bridge _CRS info on
ASRock ALiveSATA2-GLAN") whose commit message should be read for further
information.
Since commit 3e3da00c01d0 ("x86/pci: AMD one chain system to use pci
read out res") Linux gives the following oops:
Trusting the ACPI _CRS information (`pci=use_crs`) fixes this problem.
$ dmesg | grep -i crs # with the quirk
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
The match has to be against the DMI board entries though since the vendor entries are not populated.
DMI: System manufacturer System Product Name/M2V-MX SE, BIOS 0304 10/30/2007
This quirk should be removed when `pci=use_crs` is enabled for machines
from 2006 or earlier or some other solution is implemented.
Using coreboot [1] with this board the problem does not exist but this
quirk also does not affect it either. To be safe though the check is
tightened to only take effect when the BIOS from American Megatrends is
used.
15:13 < ruik> but coreboot does not need that
15:13 < ruik> because i have there only one root bus
15:13 < ruik> the audio is behind a bridge
$ sudo dmidecode
BIOS Information
Vendor: American Megatrends Inc.
Version: 0304
Release Date: 10/30/2007
This resolves a regression seen by some users of bridging.
Some users use the bridge like a dummy device.
They expect to be able to put an IPv6 address on the device
with no ports attached. Although there are better ways of doing
this, there is no reason to not allow it.
Note: the bridge still will reflect the state of ports in the
bridge if there are any added.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Wed, 5 Oct 2011 03:24:43 +0000 (03:24 +0000)]
netfilter: Use proper rwlock init function
Replace the open coded initialization with the init function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://bedivere.hansenpartnership.com/git/scsi-rc-fixes-2.6:
[SCSI] libsas: fix panic when single phy is disabled on a wide port
[SCSI] qla2xxx: Fix crash in qla2x00_abort_all_cmds() on unload
Yan, Zheng [Sun, 2 Oct 2011 04:21:50 +0000 (04:21 +0000)]
tcp: properly update lost_cnt_hint during shifting
lost_skb_hint is used by tcp_mark_head_lost() to mark the first unhandled skb.
lost_cnt_hint is the number of packets or sacked packets before the lost_skb_hint;
When shifting a skb that is before the lost_skb_hint, if tcp_is_fack() is ture,
the skb has already been counted in the lost_cnt_hint; if tcp_is_fack() is false,
tcp_sacktag_one() will increase the lost_cnt_hint. So tcp_shifted_skb() does not
need to adjust the lost_cnt_hint by itself. When shifting a skb that is equal to
lost_skb_hint, the shifted packets will not be counted by tcp_mark_head_lost().
So tcp_shifted_skb() should adjust the lost_cnt_hint even tcp_is_fack(tp) is true.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v4_clear_md5_list() assumes that multiple tcp md5sig peers
only hold one reference to md5sig_pool. but tcp_v4_md5_do_add()
increases use count of md5sig_pool for each peer. This patch
makes tcp_v4_md5_do_add() only increases use count for the first
tcp md5sig peer.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ward [Sun, 18 Sep 2011 12:53:20 +0000 (12:53 +0000)]
macvlan/macvtap: Fix unicast between macvtap interfaces in bridge mode
Packets should always be forwarded to the lowerdev using dev_forward_skb.
vlan->forward is for packets being forwarded directly to another macvlan/
macvtap device (used for multicast in bridge mode).
Reported-and-tested-by: Shlomo Pongratz <shlomop@mellanox.com> Signed-off-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 4 Oct 2011 17:37:06 +0000 (10:37 -0700)]
Merge git://github.com/davem330/net
* git://github.com/davem330/net:
pch_gbe: Fixed the issue on which a network freezes
pch_gbe: Fixed the issue on which PC was frozen when link was downed.
make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
net: xen-netback: correctly restart Tx after a VM restore/migrate
bonding: properly stop queuing work when requested
can bcm: fix incomplete tx_setup fix
RDSRDMA: Fix cleanup of rds_iw_mr_pool
net: Documentation: Fix type of variables
ibmveth: Fix oops on request_irq failure
ipv6: nullify ipv6_ac_list and ipv6_fl_list when creating new socket
cxgb4: Fix EEH on IBM P7IOC
can bcm: fix tx_setup off-by-one errors
MAINTAINERS: tehuti: Alexander Indenbaum's address bounces
dp83640: reduce driver noise
ptp: fix L2 event message recognition
Linus Torvalds [Tue, 4 Oct 2011 16:59:22 +0000 (09:59 -0700)]
Merge branch 'fix/asoc' of git://github.com/tiwai/sound
* 'fix/asoc' of git://github.com/tiwai/sound:
ASoC: omap_mcpdm_remove cannot be __devexit
ASoC: Fix setting update bits for WM8753_LADC and WM8753_RADC
ASoC: use a valid device for dev_err() in Zylonite
Jon Mason [Mon, 3 Oct 2011 14:50:20 +0000 (09:50 -0500)]
PCI: Disable MPS configuration by default
Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults. Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.
Also, add the option for peer to peer DMA MPS configuration. Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another. To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: Jon Mason <mason@myri.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Deucher [Tue, 4 Oct 2011 14:46:34 +0000 (10:46 -0400)]
drm/radeon/kms: fix channel_remap setup (v2)
Most asics just use the hw default value which requires
no explicit programming. For those that need a different
value, the vbios will program it properly. As such,
there's no need to program these registers explicitly
in the driver. Changing MC_SHARED_CHREMAP requires a reload
of all data in vram otherwise its contents will be scambled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
We found that adding load, Rx data sometimes drops.(with DMA transfer mode)
The cause is that before starting Rx-DMA processing, Tx-DMA processing starts.
This causes FIFO overrun occurs.
This patch fixes the issue by modifying FIFO tx-threshold and DMA descriptor
size like below.
Current this patch
Rx-descriptor 4Byte+12Byte*341 --> 12Byte*340-4Byte-12Byte
Rx-threshold (Not modified)
Tx-descriptor 4Byte+12Byte*341 --> 16Byte-12Byte*340
Rx-threshold 12Byte --> 2Byte
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi-topcliff-pch: add tx-memory clear after complete transmitting
Currently, in case of reading date from SPI flash,
command is sent twice.
The cause is that tx-memory clear processing is missing .
This patch adds the tx-momory clear processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Takashi Iwai [Tue, 4 Oct 2011 01:09:14 +0000 (18:09 -0700)]
lis3: fix regression of HP DriveGuard with 8bit chip
Commit 2a7fade7e03 ("hwmon: lis3: Power on corrections") caused a
regression on HP laptops with 8bit chip. Writing CTRL2_BOOT_8B bit seems
clearing the BIOS setup, and no proper interrupt for DriveGuard will be
triggered any more.
Since the init code there is basically only for embedded devices, put a
pdata check so that the problematic initialization will be skipped for
hp_accel stuff.
Borislav Petkov [Mon, 3 Oct 2011 18:28:18 +0000 (14:28 -0400)]
ide-disk: Fix request requeuing
Simon Kirby reported that on his RAID setup with idedisk underneath
the box OOMs after a couple of days of runtime. Running with
CONFIG_DEBUG_KMEMLEAK pointed to idedisk_prep_fn() which unconditionally
allocates an ide_cmd struct. However, ide_requeue_and_plug() can be
called more than once per request, either from the request issue or the
IRQ handler path and do blk_peek_request() ends up in idedisk_prep_fn()
repeatedly, allocating a struct ide_cmd everytime and "forgetting" the
previous pointer.
Make sure the code reuses the old allocated chunk.
pch_gbe: Fixed the issue on which a network freezes
The pch_gbe driver has an issue which a network stops,
when receiving traffic is high.
In the case, The link down and up are necessary to return a network.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 30 Sep 2011 10:38:28 +0000 (10:38 +0000)]
make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
This is a minor change.
Up until kernel 2.6.32, getsockopt(fd, SOL_PACKET, PACKET_STATISTICS,
...) would return total and dropped packets since its last invocation. The
introduction of socket queue overflow reporting [1] changed drop
rate calculation in the normal packet socket path, but not when using a
packet ring. As a result, the getsockopt now returns different statistics
depending on the reception method used. With a ring, it still returns the
count since the last call, as counts are incremented in tpacket_rcv and
reset in getsockopt. Without a ring, it returns 0 if no drops occurred
since the last getsockopt and the total drops over the lifespan of
the socket otherwise. The culprit is this line in packet_rcv, executed
on a drop:
As it shows, the new drop number it taken from the socket drop counter,
which is not reset at getsockopt. I put together a small example
that demonstrates the issue [2]. It runs for 10 seconds and overflows
the queue/ring on every odd second. The reported drop rates are:
ring: 16, 0, 16, 0, 16, ...
non-ring: 0, 15, 0, 30, 0, 46, 0, 60, 0 , 74.
Note how the even ring counts monotonically increase. Because the
getsockopt adds tp_drops to tp_packets, total counts are similarly
reported cumulatively. Long story short, reinstating the original code, as
the below patch does, fixes the issue at the cost of additional per-packet
cycles. Another solution that does not introduce per-packet overhead
is be to keep the current data path, record the value of sk_drops at
getsockopt() at call N in a new field in struct packetsock and subtract
that when reporting at call N+1. I'll be happy to code that, instead,
it's just more messy.
David Vrabel [Fri, 30 Sep 2011 06:37:51 +0000 (06:37 +0000)]
net: xen-netback: correctly restart Tx after a VM restore/migrate
If a VM is saved and restored (or migrated) the netback driver will no
longer process any Tx packets from the frontend. xenvif_up() does not
schedule the processing of any pending Tx requests from the front end
because the carrier is off. Without this initial kick the frontend
just adds Tx requests to the ring without raising an event (until the
ring is full).
This was caused by 47103041e91794acdbc6165da0ae288d844c820b (net:
xen-netback: convert to hw_features) which reordered the calls to
xenvif_up() and netif_carrier_on() in xenvif_connect().
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Fri, 23 Sep 2011 10:53:34 +0000 (10:53 +0000)]
bonding: properly stop queuing work when requested
During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed. I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.
There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first. There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.
This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set. I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Reported-by: Liang Zheng <lzheng@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michel Dänzer [Fri, 30 Sep 2011 15:16:53 +0000 (17:16 +0200)]
drm/radeon: Set cursor x/y to 0 when x/yorigin > 0.
Apart from the obvious cleanup, this should make the line
cursor_end = x - xorigin + w;
correct now.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Fri, 30 Sep 2011 15:16:52 +0000 (17:16 +0200)]
drm/radeon: Update AVIVO cursor coordinate origin before x/yorigin calculation.
Fixes cursor disappearing prematurely when moving off a top/left edge which
is not located at the desktop top/left edge.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Nicholas Miell <nmiell@gmail.com> Reviewed-by: Michel Dänzer <michel@daenzer.net> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Mon, 3 Oct 2011 13:13:46 +0000 (09:13 -0400)]
drm/radeon/kms: add retry limits for native DP aux defer
The previous code could potentially loop forever. Limit
the number of DP aux defer retries to 4 for native aux
transactions, same as i2c over aux transactions.
Alex Deucher [Mon, 3 Oct 2011 13:13:45 +0000 (09:13 -0400)]
drm/radeon/kms: fix regression in DP aux defer handling
An incorrect ordering in the error checking code lead
to DP aux defer being skipped in the aux native write
path. Move the bytes transferred check (ret == 0)
below the defer check.
Tracked down by: Brad Campbell <brad@fnarfbargle.com>
The following patch is admittedly a band-aid, and does not solve the
root cause, but it still is a good candidate for hardening as a pointer
check before reference.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com> Tested-by: Jack Wang <jack_wang@usish.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Roland Dreier [Thu, 22 Sep 2011 07:06:05 +0000 (00:06 -0700)]
[SCSI] qla2xxx: Fix crash in qla2x00_abort_all_cmds() on unload
I hit a crash in qla2x00_abort_all_cmds() if the qla2xxx module is
unloaded right after it is loaded. I debugged this down to the abort
handling improperly treating a command of type SRB_ADISC_CMD as if it
had a bsg_job to complete when that command actually uses the iocb_cmd
part of the union. (I guess to hit this one has to unload the module
while the async FC initialization is still in progress)
It seems we should only look for a bsg_job if type is SRB_ELS_CMD_RPT,
SRB_ELS_CMD_HST or SRB_CT_CMD, so switch the test to make that explicit.
Signed-off-by: Roland Dreier <roland@purestorage.com> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Sat, 1 Oct 2011 15:37:25 +0000 (08:37 -0700)]
Merge branches 'irq-urgent-for-linus', 'x86-urgent-for-linus' and 'sched-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip
* 'irq-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
irq: Fix check for already initialized irq_domain in irq_domain_add
irq: Add declaration of irq_domain_simple_ops to irqdomain.h
* 'x86-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86/rtc: Don't recursively acquire rtc_lock
* 'sched-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
posix-cpu-timers: Cure SMP wobbles
sched: Fix up wchan borkage
sched/rt: Migrate equal priority tasks to available CPUs
Josef Bacik [Fri, 30 Sep 2011 19:23:54 +0000 (15:23 -0400)]
Btrfs: force a page fault if we have a shorty copy on a page boundary
A user reported a problem where ceph was getting into 100% cpu usage while doing
some writing. It turns out it's because we were doing a short write on a not
uptodate page, which means we'd fall back at one page at a time and fault the
page in. The problem is our position is on the page boundary, so our fault in
logic wasn't actually reading the page, so we'd just spin forever or until the
page got read in by somebody else. This will force a readpage if we end up
doing a short copy. Alexandre could reproduce this easily with ceph and reports
it fixes his problem. I also wrote a reproducer that no longer hangs my box
with this patch. Thanks,
Reported-and-tested-by: Alexandre Oliva <aoliva@redhat.com> Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Peter Zijlstra [Thu, 1 Sep 2011 10:42:04 +0000 (12:42 +0200)]
posix-cpu-timers: Cure SMP wobbles
David reported:
Attached below is a watered-down version of rt/tst-cpuclock2.c from
GLIBC. Just build it with "gcc -o test test.c -lpthread -lrt" or
similar.
Run it several times, and you will see cases where the main thread
will measure a process clock difference before and after the nanosleep
which is smaller than the cpu-burner thread's individual thread clock
difference. This doesn't make any sense since the cpu-burner thread
is part of the top-level process's thread group.
I've reproduced this on both x86-64 and sparc64 (using both 32-bit and
64-bit binaries).
The diff of 'process' should always be >= the diff of 'thread'.
I make sure to wrap the 'thread' clock measurements the most tightly
around the nanosleep() call, and that the 'process' clock measurements
are the outer-most ones.
This is due to us using p->se.sum_exec_runtime in
thread_group_cputime() where we iterate the thread group and sum all
data. This does not take time since the last schedule operation (tick
or otherwise) into account. We can cure this by using
task_sched_runtime() at the cost of having to take locks.
This also means we can (and must) do away with
thread_group_sched_runtime() since the modified thread_group_cputime()
is now more accurate and would deadlock when called from
thread_group_sched_runtime().
Aside of that it makes the function safe on 32 bit systems. The old
code added t->se.sum_exec_runtime unprotected. sum_exec_runtime is a
64bit value and could be changed on another cpu at the same time.
Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: stable@kernel.org Link: http://lkml.kernel.org/r/1314874459.7945.22.camel@twins Tested-by: David Miller <davem@davemloft.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ALSA: hda - Fix a regression of the position-buffer check
The commit a810364a0424c297242c6c66071a42f7675a5568
ALSA: hda - Handle -1 as invalid position, too
caused a regression on some machines that require the position-buffer
instead of LPIB, e.g. resulting in noises with mic recording with
PulseAudio.
This patch fixes the detection by delaying the test at the timing as
same as 3.0, i.e. doing the position check only when requested in
azx_position_ok().
Ram Pai [Thu, 22 Sep 2011 07:48:58 +0000 (15:48 +0800)]
Resource: fix wrong resource window calculation
__find_resource() incorrectly returns a resource window which overlaps
an existing allocated window. This happens when the parent's
resource-window spans 0x00000000 to 0xffffffff and is entirely allocated
to all its children resource-windows.
__find_resource() looks for gaps in resource allocation among the
children resource windows. When it encounters the last child window it
blindly tries the range next to one allocated to the last child. Since
the last child's window ends at 0xffffffff the calculation overflows,
leading the algorithm to believe that any window in the range 0x0000000
to 0xfffffff is available for allocation. This leads to a conflicting
window allocation.
Michal Ludvig reported this issue seen on his platform. The following
patch fixes the problem and has been verified by Michal. I believe this
bug has been there for ages. It got exposed by git commit 2bbc6942273b
("PCI : ability to relocate assigned pci-resources")
Signed-off-by: Ram Pai <linuxram@us.ibm.com> Tested-by: Michal Ludvig <mludvig@logix.net.nz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'v4l_for_linus' of git://linuxtv.org/mchehab/for_linus
* 'v4l_for_linus' of git://linuxtv.org/mchehab/for_linus:
[media] omap3isp: Fix build error in ispccdc.c
[media] uvcvideo: Fix crash when linking entities
[media] v4l: Make sure we hold a reference to the v4l2_device before using it
[media] v4l: Fix use-after-free case in v4l2_device_release
[media] uvcvideo: Set alternate setting 0 on resume if the bus has been reset
[media] OMAP_VOUT: Fix build break caused by update_mode removal in DSS2
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] cio: fix cio_tpi ignoring adapter interrupts
[S390] gmap: always up mmap_sem properly
[S390] Do not clobber personality flags on exec
* git://github.com/davem330/sparc:
sparc64: Force the execute bit in OpenFirmware's translation entries.
sparc: Make '-p' boot option meaningful again.
sparc, exec: remove redundant addr_limit assignment
sparc64: Future proof Niagara cpu detection.
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux:
drm/i915: FBC off for ironlake and older, otherwise on by default
drm/i915: Enable SDVO hotplug interrupts for HDMI and DVI
drm/i915: Enable dither whenever display bpc < frame buffer bpc
powerpc: Fix device-tree matching for Apple U4 bridge
Apple Quad G5 has some oddity in it's device-tree which causes the new
generic matching code to fail to relate nodes for PCI-E devices below U4
with their respective struct pci_dev. This breaks graphics on those
machines among others.
This fixes it using a quirk which copies the node pointer from the host
bridge for the root complex, which makes the generic code work for the
children afterward.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bootup: move 'usermodehelper_enable()' a little earlier
Commit d5767c53535a ("bootup: move 'usermodehelper_enable()' to the end
of do_basic_setup()") moved 'usermodehelper_enable()' to end of
do_basic_setup() to after the initcalls. But then I get failed to let
uvesafb work on my computer, and lose the splash boot.
So maybe we could start usermodehelper_enable a little early to make
some task work that need eary init with the help of user mode.
[ I would *really* prefer that initcalls not call into user space - even
the real 'init' hasn't been execve'd yet, after all! But for uvesafb
it really does look like we don't have much choice.
I considered doing this when we mount the root filesystem, but
depending on config options that is in multiple places. We could do
the usermode helper enable as a rootfs_initcall()..
So I'm just using wang yanqing's trivial patch. It's not wonderful,
but it's simple and should work. We should revisit this some day,
though. - Linus ]
Oliver Hartkopp [Thu, 29 Sep 2011 19:33:47 +0000 (15:33 -0400)]
can bcm: fix incomplete tx_setup fix
The commit aabdcb0b553b9c9547b1a506b34d55a764745870 ("can bcm: fix tx_setup
off-by-one errors") fixed only a part of the original problem reported by
Andre Naujoks. It turned out that the original code needed to be re-ordered
to reduce complexity and to finally fix the reported frame counting issues.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log