Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A slighlty large fix for a subtle issue in the CPU hotplug code of
certain ARM SoCs, where the not yet online cpu needs to setup the cpu
local timer and needs to set the interrupt affinity to itself.
Setting interrupt affinity to a not online cpu is prohibited and
therefor the timer interrupt ends up on the wrong cpu, which leads to
nasty complications.
The SoC folks tried to hack around that in the SoC code in some more
than nasty ways. The proper solution is to have a way to enforce the
affinity setting to a not online cpu. The core patch to the genirq
code provides that facility and the follow up patches make use of it
in the GIC interrupt controller and the exynos timer driver.
The change to the core code has no implications to existing users,
except for the rename of the locked function and therefor the
necessary fixup in mips/cavium. Aside of that, no runtime impact is
possible, as none of the existing interrupt chips implements anything
which depends on the force argument of the irq_set_affinity()
callback"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Exynos_mct: Register clock event after request_irq()
clocksource: Exynos_mct: Use irq_force_affinity() in cpu bringup
irqchip: Gic: Support forced affinity setting
genirq: Allow forcing cpu affinity of interrupts
Merge tag 'tty-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few tty/serial fixes for 3.15-rc3 that resolve a number of
reported issues in the 8250 and samsung serial drivers, as well as a
character loss fix for the tty core that was caused by the lock
removal patches a release ago"
* tag 'tty-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial_core: fix uart PORT_UNKNOWN handling
serial: samsung: Change barrier() to cpu_relax() in console output
serial: samsung: don't check config for every character
serial: samsung: Use the passed in "port", fixing kgdb w/ no console
serial: 8250: Fix thread unsafe __dma_tx_complete function
8250_core: Fix unwanted TX chars write
tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc
Merge tag 'staging-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver fixes from Greg KH:
"Here are some small staging and IIO driver fixes for 3.15-rc3.
Nothing major at all, just some assorted issues that people have
reported"
* tag 'staging-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: usbdux: bug fix for accessing 'ao_chanlist' in private data
iio: adc: mxs-lradc: fix warning when buidling on avr32
iio: cm36651: Fix i2c client leak and possible NULL pointer dereference
iio: querying buffer scan_mask should return 0/1
staging:iio:ad2s1200 fix a missing break
iio: adc: at91_adc: correct default shtim value
ARM: at91: at91sam9260: change at91_adc name
ARM: at91: at91sam9g45: change at91_adc name
iio: cm32181: Fix read integration time function
iio: adc: at91_adc: Repair broken platform_data support
Merge tag 'driver-core-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some kernfs fixes for 3.15-rc3 that resolve some reported
problems. Nothing huge, but all needed"
* tag 'driver-core-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
s390/ccwgroup: Fix memory corruption
kernfs: add back missing error check in kernfs_fop_mmap()
kernfs: fix a subdir count leak
Merge tag 'usb-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.15-rc3. The majority are gadget
fixes, as we didn't get any of those in for 3.15-rc2. The others are
all over the place, and there's a number of new device id addtions as
well."
* tag 'usb-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: option: add and update a number of CMOTech devices
usb: option: add Alcatel L800MA
usb: option: add Olivetti Olicard 500
usb: qcserial: add Sierra Wireless MC7305/MC7355
usb: qcserial: add Sierra Wireless MC73xx
usb: qcserial: add Sierra Wireless EM7355
USB: io_ti: fix firmware download on big-endian machines
usb/xhci: fix compilation warning when !CONFIG_PCI && !CONFIG_PM
xhci: extend quirk for Renesas cards
xhci: Switch Intel Lynx Point ports to EHCI on shutdown.
usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb
phy: core: make NULL a valid phy reference if !CONFIG_GENERIC_PHY
phy: fix kernel oops in phy_lookup()
phy: restore OMAP_CONTROL_PHY dependencies
phy: exynos: fix building as a module
USB: serial: fix sysfs-attribute removal deadlock
usb: wusbcore: fix panic in wusbhc_chid_set
usb: wusbcore: convert nested lock to use spin_lock instead of spin_lock_irq
uwb: don't call spin_unlock_irq in a USB completion handler
usb: chipidea: coordinate usb phy initialization for different phy type
...
Merge tag 'pm+acpi-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These include a fix for a recent ACPI regression related to device
notifications, intel_idle fix related to IvyTown support, fix for a
buffer size issue in ACPICA, PM core fix related to the "freeze" sleep
state, four fixes for various types of breakage in cpufreq drivers, a
PNP workaround for a wrong memory region size in ACPI tables, and a
fix and cleanup for the ACPI tools Makefile.
Specifics:
- Fix for broken ACPI notifications on some systems caused by a
recent ACPI hotplug commit that blocked the propagation of unknown
type notifications to device drivers inadvertently.
- intel_idle fix to make the IvyTown C-states handling (added
recently) work as intended which now is broken due to missing
braces. From Christoph Jaeger.
- ACPICA fix to make it allocate buffers of the right sizes for the
Generic Serial Bus operation region access. From Lv Zheng.
- PM core fix unblocking cpuidle before entering the "freeze" sleep
state which causes that state to be able to actually save more
energy than runtime idle.
- Configuration and build fixes for the highbank and powernv cpufreq
drivers from Kefeng Wang and Srivatsa S Bhat.
- Coccinelle warning fix related to error pointers for the unicore32
cpufreq driver from Duan Jiong.
- Integer overflow fix for the ppc-corenet cpufreq driver from Geert
Uytterhoeven.
- Workaround for BIOSes that don't report the entire Intel MCH area
in their ACPI tables from Bjorn Helgaas.
- ACPI tools Makefile fix and cleanup from Thomas Renninger"
* tag 'pm+acpi-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / notify: Do not block unknown type notifications in root handler
PNP: Work around BIOS defects in Intel MCH area reporting
cpufreq: highbank: fix ARM_HIGHBANK_CPUFREQ dependency warning
cpufreq: ppc: Fix integer overflow in expression
cpufreq, powernv: Fix build failure on UP
cpufreq: unicore32: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
PM / suspend: Make cpuidle work in the "freeze" state
intel_idle: fix IVT idle state table setting
ACPICA: Fix buffer allocation issue for generic_serial_bus region accesses.
tools/power/acpi: Minor bugfixes
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of seven fixes, three (hpsa) and free'd command
references correcting bugs in the last round of updates and the
remaining four correcting problems within the SCSI error handler that
was causing a deadlock within USB"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] More USB deadlock fixes
[SCSI] Fix USB deadlock caused by SCSI error handling
[SCSI] Fix command result state propagation
[SCSI] Fix spurious request sense in error handling
[SCSI] don't reference freed command in scsi_prep_return
[SCSI] don't reference freed command in scsi_init_sgtable
[SCSI] hpsa: fix NULL dereference in hpsa_put_ctlr_into_performant_mode()
Merge tag 'fixes-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Since we didn't get around to collect fixes in time for -rc2 over the
easter vacation, this one is unfortunately a bit larger than we'd like
for an -rc3 merge.
A large set of the changes is in the device tree sources, so I'm
splitting out the description between code changes and DT changes.
Aside from omap and versatile express, the actual code bugs are and
trivial. Here is an overview:
imx:
- fix video clock settings
- fix one clock refcounting bug
omap:
- update defconfig for renamed USB PHY driver
- fix error handling in gpmc
- fix N900 video initialization regression
- fix reression in hwmod code from missing braces
- fix am43xx and omap3 clocks
- remove bogus write to voltage control register
pxa:
- fix build regression from 3.13 header cleanup
rockchip:
- fix a misleading printk string
shmobile:
- fix incorrect sound setting on multiple machines
ux500:
- enable common wireless and sensor drivers in defconfig
- more defconfig updates
vexpress:
- fix voltage calculation for opp
- fix reboot hang and warning
- fix out-of-bounds array access
- improve error handling in clock driver
overall:
- always select CLKSRC_OF in multiplatform builds
And these are the devicetree related changes:
imx:
- add missing #clock-cell properties
- fix pinctrl setting in imx6sl-evk
- fix video endpoint on imx53
- remove obsolete lvds-channel nodes (multiple patches)
- add missing second stmpe node
- fix usb host mode on dmo-edmqmx6 (multiple patches)
- fix gic node #address-cells to match usage
- add missing legacy IRQ map for PCIe
- fix microsom pincontrol setting for rgmii
- fix fatal typo in touchscreen DT usage for mx5
- list all RAM present on m53evk and mx53qsb
omap:
- fix bug in DT handling of gpmc external bus
- add DT for older revision of beagleboard
- fix regression after DT node name fixes
- remove obsolete properties for gpmc
- fix pinmux comment to match DT it refers to
- fix newly added dra7xx clock node data
- add missing clock for USB PHY
mvebu:
- add missing clock for mdio node
- fix nonstandard vendor prefixes on i2c nodes
rockchip:
- fix pin control setting for uart
shmobile:
- fix typo in DT data for pin control (multiple patches)
- fix gic node #address-cells to match usage
tegra:
- fix clock and uart DT representation to match hardware
zynq:
- add DT nodes for newly added driver
- add DT properties required for cpufreq-ondemand
overall:
- restore alphabetic order in Makefile
- grammar fixes in bindings"
* tag 'fixes-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (66 commits)
ARM: vexpress/TC2: Convert OPP voltage to uV before storing
power/reset: vexpress: Fix restart/power off operation
dt: tegra: remove non-existent clock IDs
clk: tegra: remove non-existent clocks
ARM: tegra: remove UART5/UARTE from tegra124.dtsi
ARM: tegra: remove TEGRA_EMC_SCALING_ENABLE
ARM: Tidy up DTB Makefile entries
ARM: fix missing CLKSRC_OF on multi-platform
ARM: spear: add __init to spear_clocksource_init()
ARM: pxa: hx4700.h: include "irqs.h" for PXA_NR_BUILTIN_GPIO
arm/mach-vexpress: array accessed out of bounds
clk: vexpress: NULL dereference on error path
ARM: OMAP2+: Fix GPMC remap for devices using an offset
ARM: zynq: dt: Add I2C nodes to Zynq device tree
ARM: zynq: DT: Add 'clock-latency' property
ARM: OMAP2+: Fix oops for GPMC free
ARM: dts: Add support for the BeagleBoard xM A/B
ARM: dts: Grammar /that will/it will/
ARM: dts: Grammar /is uses/ is used/
ARM: OMAP2+: Fix config name for USB3 PHY
...
Merge tag 'locks-v3.15-2' of git://git.samba.org/jlayton/linux
Pull file locking fixes from Jeff Layton:
"File locking related bugfixes for v3.15 (pile #2)
- fix for a long-standing bug in __break_lease that can cause soft
lockups
- renaming of file-private locks to "open file description" locks,
and the command macros to more visually distinct names
The fix for __break_lease is also in the pile of patches for which
Bruce sent a pull request, but I assume that your merge procedure will
handle that correctly.
For the other patches, I don't like the fact that we need to rename
this stuff at this late stage, but it should be settled now
(hopefully)"
* tag 'locks-v3.15-2' of git://git.samba.org/jlayton/linux:
locks: rename FL_FILE_PVT and IS_FILE_PVT to use "*_OFDLCK" instead
locks: rename file-private locks to "open file description locks"
locks: allow __break_lease to sleep even when break_time is 0
Merge branch 'for-3.15' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Three small nfsd bugfixes (including one locks.c fix for a bug
triggered only from nfsd).
Jeff's patches are for long-existing problems that became easier to
trigger since the addition of vfs delegation support"
* 'for-3.15' of git://linux-nfs.org/~bfields/linux:
Revert "nfsd4: fix nfs4err_resource in 4.1 case"
nfsd: set timeparms.to_maxval in setup_callback_client
locks: allow __break_lease to sleep even when break_time is 0
caused random memory corruption on my s390 box. Turns out that the
last element of the ccwgroup structure is of dynamic size, so we
must move the newly introduced work structure _before_ the zero
length array.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> CC: Tejun Heo <tj@kernel.org> CC: Martin Schwidefsky <schwidefsky@de.ibm.com> CC: Heiko Carstens <heiko.carstens@de.ibm.com> CC: Sebastian Ott <sebott@linux.vnet.ibm.com> CC: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernfs: add back missing error check in kernfs_fop_mmap()
While updating how mmap enabled kernfs files are handled by lockdep, 9b2db6e18945 ("sysfs: bail early from kernfs_file_mmap() to avoid
spurious lockdep warning") inadvertently dropped error return check
from kernfs_file_mmap(). The intention was just dropping "if
(ops->mmap)" check as the control won't reach the point if the mmap
callback isn't implemented, but I mistakenly removed the error return
check together with it.
This led to Xorg crash on i810 which was reported and bisected to the
commit and then to the specific change by Tobias.
Currently kernfs_link_sibling() increates parent->dir.subdirs before
adding the node into parent's chidren rb tree.
Because it is possible that kernfs_link_sibling() couldn't find
a suitable slot and bail out, this leads to a mismatch between
elevated subdir count with actual children node numbers.
This patches fix this problem, by moving the subdir accouting
after the actual addtion happening.
Johan Hovold [Fri, 25 Apr 2014 13:23:03 +0000 (15:23 +0200)]
USB: io_ti: fix firmware download on big-endian machines
During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.
Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
David Cohen [Fri, 25 Apr 2014 16:20:16 +0000 (19:20 +0300)]
usb/xhci: fix compilation warning when !CONFIG_PCI && !CONFIG_PM
When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]
Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.
This warning has been in since 3.2 kernel and was
caused by commit 421aa841a134f6a743111cf44d0c6d3b45e3cf8c
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
Igor Gnatenko [Fri, 25 Apr 2014 16:20:15 +0000 (19:20 +0300)]
xhci: extend quirk for Renesas cards
After suspend another Renesas PCI-X USB 3.0 card doesn't work.
[root@fedora-20 ~]# lspci -vmnnd 1912:
Device: 03:00.0
Class: USB controller [0c03]
Vendor: Renesas Technology Corp. [1912]
Device: uPD720202 USB 3.0 Host Controller [0015]
SVendor: Renesas Technology Corp. [1912]
SDevice: uPD720202 USB 3.0 Host Controller [0015]
Rev: 02
ProgIf: 30
This patch should be applied to stable kernel 3.14 that contain
the commit 1aa9578c1a9450fb21501c4f549f5b1edb557e6d
"xhci: Fix resume issues on Renesas chips in Samsung laptops"
xhci: Switch Intel Lynx Point ports to EHCI on shutdown.
The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc66ea36623dbc2757a24fc2c4ab41b016
"xhci: Fix spurious wakeups after S5 on Haswell"
Julius Werner [Fri, 25 Apr 2014 16:20:13 +0000 (19:20 +0300)]
usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb
We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.
The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.
This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.
This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae636747146ea97efa18e04576acd3416e2514f5 "USB: xhci: URB
cancellation support."
Signed-off-by: Julius Werner <jwerner@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Pfaff [Wed, 23 Apr 2014 10:33:22 +0000 (12:33 +0200)]
serial_core: fix uart PORT_UNKNOWN handling
While porting a RS485 driver from 2.6.29 to 3.14, i noticed that the serial tty
driver could break it by using uart ports that it does not own :
1. uart_change_pm ist called during uart_open and calls the uart pm function
without checking for PORT_UNKNOWN.
The fix is to move uart_change_pm from uart_open to uart_port_startup.
2. The return code from the uart request_port call in uart_set_info is not
handled properly, leading to the situation that the serial driver also
thinks it owns the uart ports.
This can triggered by doing following actions :
setserial /dev/ttyS0 uart none # release the uart ports
modprobe lirc-serial # or any other device that uses the uart
setserial /dev/ttyS0 uart 16550 # gives no error and the uart tty driver
# can use the ports as well
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com> Reviewed-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doug Anderson [Mon, 21 Apr 2014 16:40:36 +0000 (09:40 -0700)]
serial: samsung: Change barrier() to cpu_relax() in console output
The two functions to write out to the console (one used in normal
console mode and one in polling console mode) were slightly different.
One used a barrier() in its loop and the other a cpu_relax(). The
barrier() really doesn't do anything since we're using rd_regl() to
read the port anyway. Switch it to cpu_relax() to make things
consistent.
No known bugs / issues are fixed by this change--it just makes things
more consistent.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doug Anderson [Mon, 21 Apr 2014 16:40:35 +0000 (09:40 -0700)]
serial: samsung: don't check config for every character
The s3c24xx_serial_console_putchar() is _only_ ever used by
s3c24xx_serial_console_write() and is called in a loop (indirectly
through uart_console_write()). There's no reason to call
s3c24xx_port_configured() for every iteration through the loop. Move
it outside the loop.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doug Anderson [Mon, 21 Apr 2014 16:40:34 +0000 (09:40 -0700)]
serial: samsung: Use the passed in "port", fixing kgdb w/ no console
The two functions in the samsung serial driver used for writing
characters out to the port were inconsistent about whether they used
the passed in "port" or the global "cons_uart". There was no reason
to use the global and the use of the global in
s3c24xx_serial_put_poll_char() caused a crash in the case where you
used the serial port for kgdboc but not for console.
Fix it so we used the passed in variable.
Note that this doesn't fix all problems with the samsung serial
driver. Specifically:
* s3c24xx_serial_console_putchar() is still 99% identical to
s3c24xx_serial_put_poll_char() (the function signature is different,
but that's about it). A future patch will make them slightly less
identical and judging by other serial drivers we may need yet more
differences eventually.
* The samsung serial driver still doesn't allow you to have more than
one console port since it still uses the global cons_uart in
s3c24xx_serial_console_write().
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250: Fix thread unsafe __dma_tx_complete function
__dma_tx_complete is not protected against concurrent
call of serial8250_tx_dma. it can lead to circular tail
index corruption or parallel call of serial_tx_dma on the
same data portion.
This patch fixes this issue by holding the port lock.
tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc
The race was introduced while development of linux-3.11 by e8437d7ecbc50198705331449367d401ebb3181f and e9975fdec0138f1b2a85b9624e41660abd9865d4.
Originally it was found and reproduced on linux-3.12.15 and
linux-3.12.15-rt25, by sending 500 byte blocks with 115kbaud to the
target uart in a loop with 100 milliseconds delay.
In short:
1. The consumer flush_to_ldisc is on to remove the head tty_buffer.
2. The producer adds a number of bytes, so that a new tty_buffer must
be allocated and added by __tty_buffer_request_room.
3. The consumer removes the head tty_buffer element, without handling
newly committed data.
Merge tag 'vexpress/fixes-for-3.15' of git://git.linaro.org/people/pawel.moll/linux into fixes
ARM Versatile Express fixes for 3.15
This series contains straight-forward fixes for different
Versatile Express infrastructure drivers:
- NULL pointer dereference on the error path in the clk driver
- out of boundary array access in the dcscb driver
- broken restart/power off implementation
- mis-interpreted voltage unit in the spc driver
* tag 'vexpress/fixes-for-3.15' of git://git.linaro.org/people/pawel.moll/linux:
ARM: vexpress/TC2: Convert OPP voltage to uV before storing
power/reset: vexpress: Fix restart/power off operation
arm/mach-vexpress: array accessed out of bounds
clk: vexpress: NULL dereference on error path
phy: core: make NULL a valid phy reference if !CONFIG_GENERIC_PHY
This fixes a regression on Keystone 2 platforms caused by patch 57303488cd37da58263e842de134dc65f7c626d5
"usb: dwc3: adapt dwc3 core to use Generic PHY Framework" which adds
optional support of generic phy in DWC3 core.
On Keystone 2 platforms the USB is not working now because
CONFIG_GENERIC_PHY isn't set and, as result, Generic PHY APIs stubs
return -ENOSYS always. The log shows:
dwc3 2690000.dwc3: failed to initialize core
dwc3: probe of 2690000.dwc3 failed with error -38
Hence, fix it by making NULL a valid phy reference in Generic PHY
APIs stubs in the same way as it was done by the patch 04c2facad8fee66c981a51852806d8923336f362 "drivers: phy: Make NULL
a valid phy reference".
Acked-by: Felipe Balbi <balbi@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sergei Shtylyov [Sat, 19 Apr 2014 03:21:43 +0000 (08:51 +0530)]
phy: fix kernel oops in phy_lookup()
The kernel oopses in phy_lookup() due to 'phy->init_data' being NULL if we
register PHYs from a device tree probing driver and then call phy_get() on a
device that has no representation in the device tree (e.g. a PCI device).
Checking the pointer before dereferening it and skipping an interation if
it's NULL prevents this kernel oops.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean Delvare [Sat, 19 Apr 2014 03:21:42 +0000 (08:51 +0530)]
phy: restore OMAP_CONTROL_PHY dependencies
When OMAP_CONTROL_USB was renamed to OMAP_CONTROL_PHY (commit 14da699b), its dependencies were lost in the process. Nothing in the
commit message indicates that this removal was intentional, so I think
it was by accident and the dependencies should be restored.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Roger Quadros <rogerq@ti.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The top-level phy-samsung-usb2 driver may be configured as a
loadable module, which currently causes link errors because
of the dependency on the exynos{5250,4x12,4210}_usb2_phy_config
symbol. Solving this could be achieved by exporting these
symbols, but as the SoC-specific parts of the driver are not
currently built as modules, it seems better to just link
everything into one module and avoid the need for the export.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Kamil Debski <k.debski@samsung.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 23 Apr 2014 09:32:19 +0000 (11:32 +0200)]
USB: serial: fix sysfs-attribute removal deadlock
Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the
attribute.
Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in
usb_serial_probe.
The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.
As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.
Since v3.15-rc1 this also triggers the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G W
-------------------------------------------------------
modprobe/190 is trying to acquire lock:
(s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
but task is already holding lock:
(table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Thomas Pugliese [Wed, 23 Apr 2014 19:28:10 +0000 (14:28 -0500)]
usb: wusbcore: fix panic in wusbhc_chid_set
If no valid CHID value has previously been set on an HWA, writing a
value of all zeros will cause a kernel panic in uwb_radio_stop because
wusbhc->uwb_rc has not been set. This patch skips the call to
uwb_radio_stop if wusbhc->uwb_rc has not been initialized.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Pugliese [Wed, 23 Apr 2014 19:32:27 +0000 (14:32 -0500)]
usb: wusbcore: convert nested lock to use spin_lock instead of spin_lock_irq
Nesting a spin_lock_irq/unlock_irq inside a lock that has already
disabled interrupts will enable interrupts before we are ready when
spin_unlock_irq is called. This patch converts the inner lock to use
spin_lock and spin_unlock instead.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Pugliese [Wed, 23 Apr 2014 19:42:47 +0000 (14:42 -0500)]
uwb: don't call spin_unlock_irq in a USB completion handler
This patch converts the use of spin_lock_irq/spin_unlock_irq to
spin_lock_irqsave/spin_unlock_irqrestore in uwb_rc_set_drp_cmd_done
which is called from a USB completion handler. There are also
whitespace cleanups to make checkpatch.pl happy.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Thu, 24 Apr 2014 00:15:27 +0000 (08:15 +0800)]
usb: chipidea: coordinate usb phy initialization for different phy type
For internal PHY (like UTMI), the phy clock may from internal pll,
it is on/off on the fly, the access PORTSC.PTS will hang without
phy clock. So, the usb_phy_init which will open phy clock needs to
be called before hw_phymode_configure.
See: http://marc.info/?l=linux-arm-kernel&m=139350618732108&w=2
For external PHY (like ulpi), it needs to configure portsc.pts before
visit viewport, or the viewport can't be visited. so phy_phymode_configure
needs to be called before usb_phy_init.
See: cd0b42c2a6d2a74244f0053f8960f5dad5842278
It may not the best solution, but it can work for all situations.
Merge tag 'fixes-for-v3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.15-rc3
Quite a few fixes this time since I lost v3.15-rc2
window.
Most fixes are MUSB which learned to remove its debugfs directories
properly, got a fix for PHY handling and now knows that it should
make sure its clocks aren't gated before trying to access registers.
ffs got a race fix between ffs_epfile_io() and ffs_func_eps_disable().
dwc3 got a fix for system suspend/resume and now only iterates over
valid endpoints when trying to resize TX fifos.
usb_get_phy() now will properly return an error if try_module_get() fails.
We also have a revert for a NAPI conversion on the ethernet gadget which
was causing a kernel BUG.
Merge tag 'regulator-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of things here:
- Fixes for pbias that didn't make it in during the merge window due
to the driver coming in via MMC. The conversion to use helpers is
a fix as it implements list_voltage() which the main user (MMC)
relies on for correct functioning.
- Change the !REGULATOR stub for optional regulators to return an
error rather than a dummy; this is more in keeping with the
intended use of optional regulators and fixes some issues seen MMC
where it got confused by a dummy being provided"
* tag 'regulator-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Return error in get optional stub
regulator: pbias: Convert to use regmap helper functions
regulator: pbias: Fix is_enabled callback implementation
Merge tag 'spi-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here:
- SH HSPI was dealing with its clocks incorrectly which meant it
didn't work on some SoCs, fixing this also requires a small fix to
one of the SoC clock trees to avoid breaking existing users.
- The SiRF driver appears to have had several quality problems, it's
fairly new and not widely used so this isn't too worrying.
- A brute force fix for excessive locking in the Atmel driver, it
needs further investigation but this deals with the immediate
issue.
- A build fix for the Blackfin driver"
* tag 'spi-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: Fix scheduling while atomic bug
spi: sh-hspi: Do not specifically request shyway_clk clock
ARM: shmobile: r8a7778: Use clks as MSTP007 parent
spi: sirf: make GPIO chipselect function work well
spi: sirf: set SPI controller in RISC IO chipselect mode
spi: sirf: correct TXFIFO empty interrupt status bit
spi: bfin5xx: fix build error
ACPI / notify: Do not block unknown type notifications in root handler
Commit 1a699476e258 "ACPI / hotplug / PCI: Hotplug notifications from
acpi_bus_notify()" changed the root notify handler, acpi_bus_notify(),
to block unknown type norifications, but it overlooked the fact that
they might be propagated to drivers via the ->notify() callback.
Fix the problem by allowing drivers to receive unknown type
notifications via ->notify() as before.
Fixes: 1a699476e258 (ACPI / hotplug / PCI: Hotplug notifications from acpi_bus_notify()) Reported-and-tested-by: Mantas Mikulėnas <grawity@gmail.com> Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge branch 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Dan updated tag allocation to accomodate devices which choke when tags
jump back and forth. Quite a few ahci MSI related fixes. A couple
config dependency fixes and other misc fixes"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata/ahci: accommodate tag ordered controllers
ahci: Do not receive interrupts sent by dummy ports
ahci: Use pci_enable_msi_exact() instead of pci_enable_msi_range()
ahci: Ensure "MSI Revert to Single Message" mode is not enforced
ahci: do not request irq for dummy port
pata_samsung_cf: fix ata_host_activate() failure handling
pata_arasan_cf: fix ata_host_activate() failure handling
ata: fix i.MX AHCI driver dependencies
pata_at91: fix ata_host_activate() failure handling
libata: Update queued trim blacklist for M5x0 drives
libata: make AHCI_XGENE depend on PHY_XGENE
Punit Agrawal [Wed, 19 Mar 2014 12:43:25 +0000 (12:43 +0000)]
ARM: vexpress/TC2: Convert OPP voltage to uV before storing
The SPC stores voltage in mV while the code assumes it was returning
uV. Convert the returned voltage to uV before storing. Also fix the
comment depicting voltage to uV.
power/reset: vexpress: Fix restart/power off operation
The restart/power off implementation in the vexpress driver
used to obtain the config function when necessary. This was
wrong in two respects:
1. It required memory allocation with disabled interrupts
(it worked, but lockdep - when enabled - reported warnings).
2. Used jiffies-based timeout, while jiffies are not running
at this stage of system shutdown (therefore a config
transaction error - if happened - would have never be reported).
Fixed by pre-allocating the config function per device
and using mdelay for timeout.
Stephen Warren [Tue, 1 Apr 2014 20:13:17 +0000 (14:13 -0600)]
dt: tegra: remove non-existent clock IDs
The Tegra124 clock DT binding currently provides 3 clocks that don't
actually exist; 2 for NAND and one for UART5/UARTE. Delete these. While
this is technically an incompatible DT ABI change, nothing could have
used these clock IDs for anything practical, since the HW doesn't exist.
Cc: <stable@vger.kernel.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Stephen Warren [Tue, 1 Apr 2014 20:13:15 +0000 (14:13 -0600)]
ARM: tegra: remove UART5/UARTE from tegra124.dtsi
Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.
Cc: <stable@vger.kernel.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
* tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix GPMC remap for devices using an offset
ARM: OMAP2+: Fix oops for GPMC free
ARM: dts: Add support for the BeagleBoard xM A/B
ARM: dts: Grammar /that will/it will/
ARM: dts: Grammar /is uses/ is used/
ARM: OMAP2+: Fix config name for USB3 PHY
ARM: dts: am335x: update USB DT references
ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
ARM: AM335X: EVM: fix pinmux documentation in devicetree
ARM: OMAP2+: N900: remove omapdss init for DT boot
ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
ARM: dts: omap5: Add clocks to USB3 PHY node
ARM: OMAP2+: hwmod: fix missing braces in _init()
ARM: AM43xx: fix dpll init in bypass mode
ARM: OMAP3: hwmod data: Correct clock domains for USB modules
ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
This is a patch set for some ST-Ericsson devices:
- Updates the Ux500 (U8500) defconfig
- Selects PARTITION_ADVANCED for Ux500 and U300
- Configure in IIO sensor drivers for the Ux500
- Configure in the CW1200 WLAN chip for the Ux500
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: configure for CW1200 WLAN chip
ARM: ux500: configure in sensors
ARM: u300: u300_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: u8500_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: update defconfig
Merge tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Fifth Round of Renesas ARM Based SoC DT Updates for v3.15
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
* tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: correct renesas,gpios to renesas,groups in sd[02] pfc
Merge tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 3.15:
- A couple of dts changes for the fallout of imx-drm binding update
- Parent DI clocks to video PLL for better HDMI support
- PCIe interrupt mapping and GIC node fixes
- A series of edmqmx6 board fixes
- Other small and random fixes on imx5 and imx6 dts
* tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: i.MX6: ipu_di_sel clocks can set parent rates
ARM: imx6q: clk: Parent DI clocks to video PLL via di_pre_sel
ARM: dts: imx: add required #clock-cells for fixed-clock
ARM: dts: vybrid: drop address and size cells from GIC node
ARM: dts: imx6sl-evk: Add an entry for MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11
ARM: dts: imx53: fix apparent copy/paste error
ARM: dts: imx6q-gw5xxx: remove dead 'crtcs' property
ARM: dts: imx53-tx53: add IPU DI ports and endpoints
ARM: dts: imx6: edmqmx6: add second STMPE
ARM: dts: imx6: edmqmx6: USB H1 only supports host mode
ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulator
ARM: dts: imx6: edmqmx6: Fix usbotg id pin
ARM: dt: microsom: don't set bit 7 for ethernet mux settings
ARM: imx6q-clk: parent lvds_gate from lvds_sel
ARM: dts: imx: drop invalid size and address cells properties
ARM: dts: mx5: fix wrong stmpe-ts bindings
ARM: dts: imx53-m53evk: Fix memory region description
ARM: dts: imx53-qsb-common: Fix memory region description
ARM: dts: imx6: add PCIe interrupt mapping properties
Merge tag 'mvebu-dt-fixes-non-crit-3.15' of git://git.infradead.org/linux-mvebu into fixes
mvebu DT fixes-non-critical (for v3.15-rc1)
- kirkwood
- add some missing vendor prefixes to keep checkpatch happy
- mvebu
- add clock ref to mdio node on 370/XP/38x
* tag 'mvebu-dt-fixes-non-crit-3.15' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: ensure the mdio node has a clock reference on Armada 38x
ARM: mvebu: ensure the mdio node has a clock reference on Armada 370/XP
ARM: Kirkwood: DT: Add missing vendor prefix
ARM: Kirkwood: Fix Atmel vendor prefix
Rob Herring [Wed, 16 Apr 2014 13:42:13 +0000 (08:42 -0500)]
ARM: fix missing CLKSRC_OF on multi-platform
In commit ddb902cc34593e (ARM: centralize common multi-platform kconfig
options), CLKSRC_OF was removed from some platforms, but not added to
ARCH_MULTIPLATFORM. Fix this.
Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix build errors. Initial one is:
/linux/arch/arm/mach-pxa/include/mach/hx4700.h:18:32: error:
'PXA_NR_BUILTIN_GPIO' undeclared here (not in a function)
| #define HX4700_ASIC3_GPIO_BASE PXA_NR_BUILTIN_GPIO
The driver used to directly us a DT 'compatible' property for
the 'name' attribute of the hwmon devices. Unfortunately it
contains '-' which is illegal in this context. It messes up
libsensors and thus every application using it.
Fixed by providing equivalent (and simpler) name strings.
PNP: Work around BIOS defects in Intel MCH area reporting
Work around BIOSes that don't report the entire Intel MCH area.
MCHBAR is not an architected PCI BAR, so MCH space is usually reported as a
PNP0C02 resource. The MCH space was once 16KB, but is 32KB in newer parts.
Some BIOSes still report a PNP0C02 resource that is only 16KB, which means
the rest of the MCH space is consumed but unreported.
This can cause resource map sanity check warnings or (theoretically) a
device conflict if we assigned the unreported space to another device.
The Intel perf event uncore driver tripped over this when it claimed the
MCH region:
resource map sanity check conflict: 0xfed10000 0xfed15fff 0xfed10000 0xfed13fff pnp 00:01
Info: mapping multiple BARs. Your kernel is fine.
To prevent this, if we find a PNP0C02 resource that covers part of the MCH
space, extend it to cover the entire space.
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Various fixes and post-merge window updates. Included here are:
- ensure Kconfig things which should be sorted remain sorted
- fix three big-endian bugs which crept in during the last merge
window
- add the renameat2 syscall
- fix big.LITTLE switcher initialisation checks
- fix kdump vmcore for LPAE kernels"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: add renameat2 syscall
ARM: keep arch/arm/Kconfig and arch/arm/mm/Kconfig select entries sorted
ARM: 8033/1: fix big endian __pv_phys_pfn_offset size related issue
ARM: 8032/1: bL_switcher: fix validation check before its activation
ARM: 8030/1: ARM : kdump : add arch_crash_save_vmcoreinfo
ARM: 8027/1: fix do_div() bug in big-endian systems
ARM: 8026/1: Fix emulation of multiply accumulate instructions
ARM: 8024/1: Keep DEBUG_UART_{PHYS,VIRT} entries sorted
staging: comedi: usbdux: bug fix for accessing 'ao_chanlist' in private data
In usbdux_ao_cmd(), the channels for the command are transfered from the
cmd->chanlist and stored in the private data 'ao_chanlist'. The channel
numbers are bit-shifted when stored so that they become the "command"
that is transfered to the device. The channel to command conversion
results in the 'ao_chanlist' having these values for the channels:
The problem is, the usbduxsub_ao_isoc_irq() function uses the 'chan' value
from 'ao_chanlist' to access the 'ao_readback' array in the private data.
So instead of accessing the array as 0, 1, 2, 3, it accesses it as 0x00,
0x40, 0x80, 0xc0.
Fix this by storing the raw channel number in 'ao_chanlist' and doing the
bit-shift when creating the command.
Fixes: a998a3db530bff80 "staging: comedi: usbdux: cleanup the private data 'outBuffer'" Cc: stable <stable@vger.kernel.org> # 3.12 Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Acked-by: Bernd Porr <mail@berndporr.me.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren [Tue, 22 Apr 2014 02:26:13 +0000 (19:26 -0700)]
ARM: OMAP2+: Fix GPMC remap for devices using an offset
At least the smc91x driver expects the device to be at 0x300
offset from bus base address. This does not work currently
for GPMC when booted in device tree mode as it attempts to
remap the the allocated GPMC partition to the address
configured by the device tree plus the device offset.
Note that this works just fine when booted with legacy mode.
Let's fix the issue by just ignoring any device specific
offset while remapping. And let's make sure the remap
address confirms to the GPMC 16MB minimum granularity
as listed in the TRM for GPMC_CONFIG7 BASEADDRESS bits.
Otherwise we can get something like this:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Cc: Pekon Gupta <pekon@ti.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"The main change is that we now publish "firmware ID" for the serio
devices to help userspace figure out the kind of touchpads it is
dealing with: i8042 will export PS/2 port's PNP IDs as firmware IDs.
You will also get more quirks for Synaptics touchpads in various
Lenovo laptops, a change to elantech driver to recognize even more
models, and fixups to wacom and couple other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for newer elantech touchpads
Input: soc_button_array - fix a crash during rmmod
Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1
Input: synaptics - report INPUT_PROP_TOPBUTTONPAD property
Input: Add INPUT_PROP_TOPBUTTONPAD device property
Input: i8042 - add firmware_id support
Input: serio - add firmware_id sysfs attribute
Input: wacom - handle 1024 pressure levels in wacom_tpc_pen
Input: wacom - references to 'wacom->data' should use 'unsigned char*'
Input: wacom - override 'pressure_max' with value from HID_USAGE_PRESSURE
Input: wacom - use full 32-bit HID Usage value in switch statement
Input: wacom - missed the last bit of expresskey for DTU-1031
Input: ads7846 - fix device usage within attribute show
Input: da9055_onkey - remove use of regmap_irq_get_virq()
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull radeon drm fixes from Dave Airlie:
"This is just radeon fixes, primarily the two pll fix and the aux fix,
it also disables dpm on rv770 gpus, fixes driver reloading, and fixes
two issues with runtime PM on some GPUS"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: don't allow runpm=1 on systems with out ATPX
drm/radeon: fix ATPX detection on non-VGA GPUs
drm/radeon/pm: don't walk the crtc list before it has been initialized (v2)
drm/radeon: properly unregister hwmon interface (v2)
drm/radeon: fix count in cik_sdma_ring_test()
drm/radeon/aux: fix hpd assignment for aux bus
drm/radeon: improve PLL limit handling in post div calculation
drm/radeon: use fixed PPL ref divider if needed
drm/radeon: disable dpm on rv770 by default
68efd7d2fb("arm: dma-mapping: remove order parameter from
arm_iommu_create_mapping()") is causing kernel panic
because it wrongly sets the value of mapping->size:
Unable to handle kernel NULL pointer dereference at virtual
address 000000a0
pgd = e7a84000
[000000a0] *pgd=00000000
...
PC is at bitmap_clear+0x48/0xd0
LR is at __iommu_remove_mapping+0x130/0x164
Jordan Rife [Wed, 23 Apr 2014 00:44:51 +0000 (17:44 -0700)]
Input: elantech - add support for newer elantech touchpads
Newer elantech touchpads are not recognized by the current driver, since it
fails to detect their firmware version number. This prevents more advanced
touchpad features from being usable such as two-finger scrolling. This
patch allows newer touchpads to be detected and be fully functional. Tested
on Sony Vaio SVF13N17PXB.
Signed-off-by: Jordan Rife <jrife0@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Merge tag 'iio-fixes-for-3.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First found of IIO fixes for the 3.15 cycle.
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
Dave Airlie [Tue, 22 Apr 2014 21:39:12 +0000 (07:39 +1000)]
Merge branch 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux into drm-next
1. Further PLL parameter fixes.
2. Fixes for HPD on DP
3. Could of different PM fixes
4. Disabling DPM on RV770
* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: don't allow runpm=1 on systems with out ATPX
drm/radeon: fix ATPX detection on non-VGA GPUs
drm/radeon/pm: don't walk the crtc list before it has been initialized (v2)
drm/radeon: properly unregister hwmon interface (v2)
drm/radeon: fix count in cik_sdma_ring_test()
drm/radeon/aux: fix hpd assignment for aux bus
drm/radeon: improve PLL limit handling in post div calculation
drm/radeon: use fixed PPL ref divider if needed
drm/radeon: disable dpm on rv770 by default
Victor Kamensky [Tue, 22 Apr 2014 01:25:36 +0000 (02:25 +0100)]
ARM: 8033/1: fix big endian __pv_phys_pfn_offset size related issue
Fix e26a9e00afc482b971afcaef1db8c9034d4d6d7c 'ARM: Better
virt_to_page() handling' replaced __pv_phys_offset with
__pv_phys_pfn_offset. Also note that size of __pv_phys_offset
was quad but size of __pv_phys_pfn_offset is word. Instruction
that used to update __pv_phys_offset which address is in r6
had to update low word of __pv_phys_offset so it used #LOW_OFFSET
macro for store offset. Now when size of __pv_phys_pfn_offset is
word, no difference between little endian and big endian should
exist - i.e no offset should be used when __pv_phys_pfn_offset
is stored.
Note that for little endian image proposed change is noop,
since in little endian case #LOW_OFFSET is defined 0 anyway.
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Nicolas Pitre [Mon, 21 Apr 2014 23:25:35 +0000 (00:25 +0100)]
ARM: 8032/1: bL_switcher: fix validation check before its activation
The switcher should not depend on MAX_CLUSTER to determine ifit should
be activated or not. In a multiplatform kernel binary it is possible to
have dual-cluster and quad-cluster platforms configured in. In that case
MAX_CLUSTER which is a build time limit should be 4 and that shouldn't
prevent the switcher from working if the kernel is booted on a b.L
dual-cluster system.
In bL_switcher_halve_cpus() we already have a runtime validation check
to make sure we're dealing with only two clusters, so booting on a quad
cluster system will be caught and switcher activation aborted.
However, the b.L switcher must ensure the MCPM layer is initialized on
the booted hardware before doing anything. The mcpm_is_available()
function is added to that effect.
Signed-off-by: Nicolas Pitre <nico@linaro.org> Tested-by: Abhilash Kesavan <kesavan.abhilash@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Liu Hua [Fri, 18 Apr 2014 06:45:36 +0000 (07:45 +0100)]
ARM: 8030/1: ARM : kdump : add arch_crash_save_vmcoreinfo
For vmcore generated by LPAE enabled kernel, user space
utility such as crash needs additional infomation to
parse.
So this patch add arch_crash_save_vmcoreinfo as what PAE enabled
i386 linux does.
Cc: <stable@vger.kernel.org> Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Liu Hua <sdu.liu@huawei.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When viewed ftrace records, it will call the do_div(n, base) function, which achieved arch/arm/include/asm/div64.h in. When n = 10000000, base = 1000000, in do_div(n, base) will execute "umull %Q0, %R0, %1, %Q2".
Reviewed-by: Dave Martin <Dave.Martin@arm.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Cc: <stable@vger.kernel.org> # 2.6.20+ Signed-off-by: Alex Wu <wuquanming@huawei.com> Signed-off-by: Xiangyu Lu <luxiangyu@huawei.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mm: make fixup_user_fault() check the vma access rights too
fixup_user_fault() is used by the futex code when the direct user access
fails, and the futex code wants it to either map in the page in a usable
form or return an error. It relied on handle_mm_fault() to map the
page, and correctly checked the error return from that, but while that
does map the page, it doesn't actually guarantee that the page will be
mapped with sufficient permissions to be then accessed.
So do the appropriate tests of the vma access rights by hand.
[ Side note: arguably handle_mm_fault() could just do that itself, but
we have traditionally done it in the caller, because some callers -
notably get_user_pages() - have been able to access pages even when
they are mapped with PROT_NONE. Maybe we should re-visit that design
decision, but in the meantime this is the minimal patch. ]
Found by Dave Jones running his trinity tool.
Reported-by: Dave Jones <davej@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'gpio-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"A small batch of GPIO fixes for the v3.15 series. I expect more to
come in but I'm a bit behind on mail, might as well get these to you
right now:
- Change a crucial semantic ordering in the GPIO irqchip helpers
- Fix two nasty regressions in the ACPI gpiolib extensions"
* tag 'gpio-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio / ACPI: Prevent potential wrap of GPIO value on OpRegion read
gpio / ACPI: Don't crash on NULL chip->dev
gpio: set data first, then chip and handler
Merge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso fix from Peter Anvin:
"This is a single build fix for building with gold as opposed to GNU
ld. It got queued up separately and was expected to be pushed during
the merge window, but it got left behind"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Make the vdso linker script compatible with Gold