Commit fa8b18ed didn't prevent the integer overflow and possible
memory corruption. "count" can go negative and bypass the check.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: cdc-acm: Fix acm_tty_hangup() vs. acm_tty_close() race
[Not upstream as it was fixed differently for 3.3 with a much more
"intrusive" rework of the driver - gregkh]
There is a race condition involving acm_tty_hangup() and acm_tty_close()
where hangup() would attempt to access tty->driver_data without proper
locking and NULL checking after close() has potentially already set it
to NULL. One possibility to (sporadically) trigger this behavior is to
perform a suspend/resume cycle with a running WWAN data connection.
This patch addresses the issue by introducing a NULL check for
tty->driver_data in acm_tty_hangup() protected by open_mutex and exiting
gracefully when hangup() is invoked on a device that has already been
closed.
If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.
The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves
The fix is to detach the slave (which removes it from the list)
in the unwind path.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At this point if skb->len happens to be 2, the subsequant skb_pull(skb, 4)
call won't work and the skb->len won't be decreased and won't ever reach 0,
resulting in an infinite loop.
With an ASIX 88772 under heavy load, without this patch, rx_fixup() reaches
an infinite loop in less than a minute. With this patch applied,
no infinite loop even after hours of heavy load.
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b7c84066733c5dfb0e4016d939757b38de189e4 ('ipv4: correct IGMP
behavior on v3 query during v2-compatibility mode') added yet another
case for query parsing, which can result in max_delay = 0. Substitute
a value of 1, as in the usual v3 case.
Reported-by: Simon McVittie <smcv@debian.org>
References: http://bugs.debian.org/654876 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
[ removed the dwc3 portion of the patch as it didn't apply to
older kernels - gregkh]
According to USB 3.0 Specification Table 9-22, if
bmAttributes [4:0] are set to zero, it means "no
streams supported", but the way this helper was
defined on Linux, we will *always* have one stream
which might cause several problems.
For example on DWC3, we would tell the controller
endpoint has streams enabled and yet start transfers
with Stream ID set to 0, which would goof up the host
side.
While doing that, convert the macro to an inline
function due to the different checks we now need.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered a result of COMP_2ND_BW_ERR while improving how the pwc
webcam driver handles not having the full usb1 bandwidth available to
itself.
I created the following test setup, a NEC xhci controller with a
single TT USB 2 hub plugged into it, with a usb keyboard and a pwc webcam
plugged into the usb2 hub. This caused the following to show up in dmesg
when trying to stream from the pwc camera at its highest alt setting:
xhci_hcd 0000:01:00.0: ERROR: unexpected command completion code 0x23.
usb 6-2.1: Not enough bandwidth for altsetting 9
And usb_set_interface returned -EINVAL, which caused my pwc code to not
do the right thing as it expected -ENOSPC.
This patch makes the xhci driver properly handle COMP_2ND_BW_ERR and makes
usb_set_interface return -ENOSPC as expected.
This should be backported to stable kernels as old as 2.6.32.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new field num_mapped_sgs to struct urb so that we have a place to
store the number of mapped entries and can also retain the original
value of entries in num_sgs. Previously, usb_hcd_map_urb_for_dma()
would overwrite this with the number of mapped entries, which would
break dma_unmap_sg() because it requires the original number of entries.
This fixes warnings like the following when using USB storage devices:
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:902 check_unmap+0x4e4/0x695()
ehci_hcd 0000:00:12.2: DMA-API: device driver frees DMA sg list with different entry count [map count=4] [unmap count=1]
Modules linked in: ohci_hcd ehci_hcd
Pid: 0, comm: kworker/0:1 Not tainted 3.2.0-rc2+ #319
Call Trace:
<IRQ> [<ffffffff81036d3b>] warn_slowpath_common+0x80/0x98
[<ffffffff81036de7>] warn_slowpath_fmt+0x41/0x43
[<ffffffff811fa5ae>] check_unmap+0x4e4/0x695
[<ffffffff8105e92c>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff8147208b>] ? _raw_spin_unlock_irqrestore+0x33/0x50
[<ffffffff811fa84a>] debug_dma_unmap_sg+0xeb/0x117
[<ffffffff8137b02f>] usb_hcd_unmap_urb_for_dma+0x71/0x188
[<ffffffff8137b166>] unmap_urb_for_dma+0x20/0x22
[<ffffffff8137b1c5>] usb_hcd_giveback_urb+0x5d/0xc0
[<ffffffffa0000d02>] ehci_urb_done+0xf7/0x10c [ehci_hcd]
[<ffffffffa0001140>] qh_completions+0x429/0x4bd [ehci_hcd]
[<ffffffffa000340a>] ehci_work+0x95/0x9c0 [ehci_hcd]
...
---[ end trace f29ac88a5a48c580 ]---
Mapped at:
[<ffffffff811faac4>] debug_dma_map_sg+0x45/0x139
[<ffffffff8137bc0b>] usb_hcd_map_urb_for_dma+0x22e/0x478
[<ffffffff8137c494>] usb_hcd_submit_urb+0x63f/0x6fa
[<ffffffff8137d01c>] usb_submit_urb+0x2c7/0x2de
[<ffffffff8137dcd4>] usb_sg_wait+0x55/0x161
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for Chinese Noname HSPA USB modem which is apparently
manufactured by a company called ZD Incorporated (based on texts in the
Windows drivers).
This product is available at least from Dealextreme (SKU 80032) and
possibly in India with name Olive V-MW250. It is based on Qualcomm
MSM6280 chip.
I needed to also add "options usb-storage quirks=0685:7000:i" in modprobe
configuration because udevd or the kernel keeps poking the embedded
fake-cd-rom which fails and causes the device to reset. There might be
a better way to accomplish the same. usb_modeswitch is not needed with
this device.
Signed-off-by: Janne Snabb <snabb@epipe.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix regression introduced by commit 507ca9bc047666 ([PATCH] USB: add
ability for usb-serial drivers to determine if their write urb is
currently being used.) which inverted the logic in write_room so that it
returns zero when the write urb is actually free.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In musb_init_controller() there's a pm_runtime_put(), but there's no
pm_runtime_get(), which creates a mismatch that causes the driver to
sleep when it shouldn't.
This was introduced in 7acc619[1], but it wasn't triggered in my setup
until 18a2689[2] was merged to Linus' branch at point df0914[3]. IOW;
when PM is working as it was supposed to.
However, it seems most of the time this is used in a way that keeps the
counter above 0, so nobody noticed. Also, it seems to depend on the
configuration used in versions before 3.1, but not later (or in it).
I found the problem by loading isp1704_charger before any usb gadgets:
http://article.gmane.org/gmane.linux.kernel/1226122
All versions after 2.6.39 are affected.
[1] usb: musb: Idle path retention and offmode support for OMAP3
[2] OMAP2+: musb: hwmod adaptation for musb registration
[3] Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
Cc: Hema HK <hemahk@ti.com> Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
After commit c430131a02d677aa708f56342c1565edfdacb3c0 (Support
controllers with big endian capability regs), HC_LENGTH takes
two arguments. This patch fixes following compilation error:
In file included from drivers/usb/host/ehci-hcd.c:1323:
drivers/usb/host/ehci-pxa168.c:302:54: error: macro "HC_LENGTH" requires 2 arguments, but only 1 given
In file included from drivers/usb/host/ehci-hcd.c:1323:
drivers/usb/host/ehci-pxa168.c: In function 'ehci_pxa168_drv_probe':
drivers/usb/host/ehci-pxa168.c:302: error: 'HC_LENGTH' undeclared (first use in this function)
drivers/usb/host/ehci-pxa168.c:302: error: (Each undeclared identifier is reported only once
drivers/usb/host/ehci-pxa168.c:302: error: for each function it appears in.)
Echo vendor and product number of a non usb-storage device to
usb-storage driver's new_id, then plug in the device to host and you
will find following oops msg, the root cause is usb_stor_probe1()
refers invalid id entry if giving a dynamic id, so just disable the
feature.
We were sending data on the stack when uploading firmware, which causes
some machines fits, and is not allowed. Fix this by using the buffer we
already had around for this very purpose.
Reported-by: Wouter M. Koolen <wmkoolen@cwi.nl> Tested-by: Wouter M. Koolen <wmkoolen@cwi.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some failures, the country_code field of an acm structure is freed
without freeing the acm structure itself. Elsewhere, operations including
memcpy and kfree are performed on the country_code field. The patch sets
the country_code field to NULL when it is freed, and likewise sets the
country_code_size field to 0.
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During BKL removal in 2.6.38, conversion of files from in-ICB format to normal
format got broken. We call ->writepage with i_data_sem held but udf_get_block()
also acquires i_data_sem thus creating A-A deadlock.
We fix the problem by dropping i_data_sem before calling ->writepage() which is
safe since i_mutex still protects us against any changes in the file. Also fix
pagelock - i_data_sem lock inversion in udf_expand_file_adinicb() by dropping
i_data_sem before calling find_or_create_page().
Reported-by: Matthias Matiak <netzpython@mail-on.us> Tested-by: Matthias Matiak <netzpython@mail-on.us> Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we mount a hierarchy with a specified name, the name is unique,
and we can use it to mount the hierarchy without specifying its
set of subsystem names. This feature is documented is
Documentation/cgroups/cgroups.txt section 2.3
Here's an example:
# mount -t cgroup -o cpuset,name=myhier xxx /cgroup1
# mount -t cgroup -o name=myhier xxx /cgroup2
When running the Point Grey "flycap" program for their USB 3.0 camera
(which was running as a USB 2.0 device for some reason), I trigger this
oops whenever I try to open a video stream:
The documentation for usbmon is out of date; the usbfs "devices" file
now exists in /sys/kernel/debug/usb rather than /proc/bus/usb. This
patch (as1505) updates the documentation accordingly, and also
mentions that the necessary information can be found by running lsusb.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function vmbus_exists() was introduced recently to deal with cases where
the vmbus driver failed to initialize and yet other Hyper-V drivers attempted
to register with the vmbus bus driver. This patch introduced a bug where
vmbus_driver_unregister() would fail to unregister the driver. This patch
fixes the problem.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Fuzhou Chen <fuzhouch@microsoft.com> Cc: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hv vmbus driver was causing an OOPS since it was trying to register drivers
on top of the bus even if initialization of the bus has failed for some
reason (such as the odd chance someone would run a hv enabled kernel in a
non-hv environment).
Signed-off-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARN_ON_ONCE(IS_RDONLY(inode)) tends to trip when filesystem hits error and is
remounted read-only. This unnecessarily scares users (well, they should be
scared because of filesystem error, but the stack trace distracts them from the
right source of their fear ;-). We could as well just remove the WARN_ON but
it's not hard to fix it to not trip on filesystem with errors and not use more
cycles in the common case so that's what we do.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a crash in reiserfs_delete_xattrs during umount.
When shrink_dcache_for_umount clears the dcache from
generic_shutdown_super, delayed evictions are forced to disk. If an
evicted inode has extended attributes associated with it, it will
need to walk the xattr tree to locate and remove them.
But since shrink_dcache_for_umount will BUG if it encounters active
dentries, the xattr tree must be released before it's called or it will
crash during every umount.
This patch forces the evictions to occur before generic_shutdown_super
by calling shrink_dcache_sb first. The additional evictions caused
by the removal of each associated xattr file and dir will be automatically
handled as they're added to the LRU list.
CC: reiserfs-devel@vger.kernel.org Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When MISC_FILESYSTEMS is not enabled and NFS4.1 is:
fs/built-in.o: In function `objio_alloc_io_state':
objio_osd.c:(.text+0xcb525): undefined reference to `ore_get_rw_state'
fs/built-in.o: In function `_write_done':
objio_osd.c:(.text+0xcb58d): undefined reference to `ore_check_io'
fs/built-in.o: In function `_read_done':
...
When MISC_FILESYSTEMS, which is more of a GUI thing then anything else,
is not selected. exofs/Kconfig is never examined during Kconfig,
and it can not do it's magic stuff to automatically select everything
needed.
We must split exofs/Kconfig in two. The ore one is always included.
And the exofs one is left in it's old place in the menu.
NFS might send us offsets that are not PAGE aligned. So
we must read in the reminder of the first/last pages, in cases
we need it for Parity calculations.
We only add an sg segments to read the partial page. But
we don't mark it as read=true because it is a lock-for-write
page.
TODO: In some cases (IO spans a single unit) we can just
adjust the raid_unit offset/length, but this is left for
later Kernels.
When reading RAID5 files, in rare cases, we calculated too
few sg segments. There should be two extra for the beginning
and end partial units.
Also "too few sg segments" should not be a BUG_ON there is
all the mechanics in place to handle it, as a short read.
So just return -ENOMEM and the rest of the code will gracefully
split the IO.
The users of ore_check_io() expect the reported device
(In case of error) to be indexed relative to the passed-in
ore_components table, and not the logical dev index.
This causes a crash inside objlayoutdriver in case of
an IO error.
A update is made to the sched:sched_switch event that adds some
logic to the first parameter of the __print_flags() that shows the
state of tasks. This change cause perf to fail parsing the flags.
A simple fix is needed to have the parser be able to process ops
within the argument.
Reported-by: Andrew Vagin <avagin@openvz.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ICT code erroneously uses PAGE_SIZE. The bug
is that PAGE_SIZE isn't necessarily 4096, so on
such platforms this code will not work correctly
as we'll try to attempt to read an index in the
table that the device never wrote, it always has
4096-byte pages.
Additionally, the manual alignment code here is
unnecessary -- Documentation/DMA-API-HOWTO.txt
states:
The cpu return address and the DMA bus master address are both
guaranteed to be aligned to the smallest PAGE_SIZE order which
is greater than or equal to the requested size. This invariant
exists (for example) to guarantee that if you allocate a chunk
which is smaller than or equal to 64 kilobytes, the extent of the
buffer you receive will not cross a 64K boundary.
Just use appropriate new constants and get rid of
the alignment code.
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver everywhere uses max TID count as 9,
which is wrong, it should be 8.
I think the reason it uses 9 here is off-by-one
confusion by whoever wrote this. We do use the
value IWL_MAX_TID_COUNT for "not QoS/no TID"
but that is completely correct even if it is 8
and not 9 since 0-7 are only valid.
As a side effect, this fixes the following bug:
Open BA session requested for 00:23:cd:16:8a:7e tid 8
------------[ cut here ]------------
kernel BUG at drivers/net/wireless/iwlwifi/iwl-trans-pcie-int.h:350!
...
when you do
echo "tx start 8" > /sys/kernel/debug/ieee80211/*/*/*/*/agg_status
Reported-by: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Userspace verbs multicast attach/detach operations on a QP are done
while holding the rwsem of the QP for reading. That's not sufficient
since a reader lock allows more than one reader to acquire the
lock. However, multicast attach/detach does list manipulation that
can corrupt the list if multiple threads run in parallel.
Fix this by acquiring the rwsem as a writer to serialize attach/detach
operations. Add idr_write_qp() and put_qp_write() to encapsulate
this.
This fixes oops seen when running applications that perform multicast
joins/leaves.
Reported by: Mike Dubman <miked@mellanox.com> Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prevent a receive data corruption by ensuring that the write to update
the rcvhdrheadn register to generate an interrupt is at the very end
of the receive processing.
Signed-off-by: Ramkrishna Vepa <ram.vepa@qlogic.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
where:
A => B and A -> B means A calls B, but
=> means A will call B through function name, and B will definitely be
called.
-> means A will call B through function pointer, so B might not be
called if the function pointer is not set.
So error happens when only one of probe_hcall_entry and probe_hcall_exit
get called during a hcall.
This patch tries to move the preempt count operations from
probe_hcall_entry and probe_hcall_exit to its callers.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When re-enabling interrupts we have code to handle edge sensitive
decrementers by resetting the decrementer to 1 whenever it is negative.
If interrupts were disabled long enough that the decrementer wrapped to
positive we do nothing. This means interrupts can be delayed for a long
time until it finally goes negative again.
While we hope interrupts are never be disabled long enough for the
decrementer to go positive, we have a very good test team that can
drive any kernel into the ground. The softlockup data we get back
from these fails could be seconds in the future, completely missing
the cause of the lockup.
We already keep track of the timebase of the next event so use that
to work out if we should trigger a decrementer exception.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An nvs with malformed contents could cause the processing of the
calibration data to read beyond the end of the buffer. Prevent this
from happening by adding bound checking.
The libertas scan thread expects priv->scan_req to be non-NULL. In theory,
it should always be set. In practice, we've seen the following oops:
[ 8363.067444] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 8363.067490] pgd = c0004000
[ 8363.078393] [00000004] *pgd=00000000
[ 8363.086711] Internal error: Oops: 17 [#1] PREEMPT
[ 8363.091375] Modules linked in: fuse libertas_sdio libertas psmouse mousedev ov7670 mmp_camera joydev videobuf2_core videobuf2_dma_sg videobuf2_memops [last unloaded: scsi_wait_scan]
[ 8363.107490] CPU: 0 Not tainted (3.0.0-gf7ccc69 #671)
[ 8363.112799] PC is at lbs_scan_worker+0x108/0x5a4 [libertas]
[ 8363.118326] LR is at 0x0
[ 8363.120836] pc : [<bf03a854>] lr : [<00000000>] psr: 60000113
[ 8363.120845] sp : ee66bf48 ip : 00000000 fp : 00000000
[ 8363.120845] r10: ee2c2088 r9 : c04e2efc r8 : eef97005
[ 8363.132231] r7 : eee0716f r6 : ee2c02c0 r5 : ee2c2088 r4 : eee07160
[ 8363.137419] r3 : 00000000 r2 : a0000113 r1 : 00000001 r0 : eee07160
[ 8363.143896] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 8363.157630] Control: 10c5387d Table: 2e754019 DAC: 00000015
[ 8363.163334] Process kworker/u:1 (pid: 25, stack limit = 0xee66a2f8)
While I've not found a smoking gun, there are two places that raised red flags
for me. The first is in _internal_start_scan, when we queue up a scan; we
first queue the worker, and then set priv->scan_req. There's theoretically
a 50mS delay which should be plenty, but doing things that way just seems
racy (and not in the good way).
The second is in the scan worker thread itself. Depending on the state of
priv->scan_channel, we cancel pending scan runs and then requeue a run in
300mS. We then send the scan command down to the hardware, sleep, and if
we get scan results for all the desired channels, we set priv->scan_req to
NULL. However, it that's happened in less than 300mS, what happens with
the pending scan run?
This patch addresses both of those concerns. With the patch applied, we
have not seen the oops in the past two weeks.
Signed-off-by: Andres Salomon <dilinger@queued.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using a >8bpp framebuffer, offb advertises truecolor, not directcolor,
and doesn't touch the color map even if it has a corresponding access method
for the real hardware.
Thus it needs to set the pseudo-palette with all 3 components of the color,
like other truecolor framebuffers, not with copies of the color index like
a directcolor framebuffer would do.
This went unnoticed for a long time because it's pretty hard to get offb
to kick in with anything but 8bpp (old BootX under MacOS will do that and
qemu does it).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Testing on the openSUSE wireless forum has shown that a Linksys
WUSB54GC v3 with USB ID 1737:0077 works with rt2800usb when the ID is
written to /sys/.../new_id. This ID can therefore be moved out of UNKNOWN.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This oops was reported recently:
firmware_loading_store+0xf9/0x17b
dev_attr_store+0x20/0x22
sysfs_write_file+0x101/0x134
vfs_write+0xac/0xf3
sys_write+0x4a/0x6e
system_call_fastpath+0x16/0x1b
The complete backtrace was unfortunately not captured, but details can be found
here:
https://bugzilla.redhat.com/show_bug.cgi?id=769920
The cause is fairly clear.
Its caused by the fact that firmware_loading_store has a case 0 in its
switch statement that reads and writes the fw_priv->fw poniter without the
protection of the fw_lock mutex. since there is a window between the time that
_request_firmware sets fw_priv->fw to NULL and the time the corresponding sysfs
file is unregistered, its possible for a user space application to race in, and
write a zero to the loading file, causing a NULL dereference in
firmware_loading_store. Fix it by extending the protection of the fw_lock mutex
to cover all of the firware_loading_store function.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fix CAN MAINTAINERS SCM tree type
mwifiex: fix crash during simultaneous scan and connect
b43: fix regression in PIO case
ath9k: Fix kernel panic in AR2427 in AP mode
CAN MAINTAINERS update
net: fsl: fec: fix build for mx23-only kernel
sch_qfq: fix overflow in qfq_update_start()
Revert "Bluetooth: Increase HCI reset timeout in hci_dev_do_close"
Al Viro [Wed, 4 Jan 2012 10:51:03 +0000 (10:51 +0000)]
minixfs: misplaced checks lead to dentry leak
bitmap size sanity checks should be done *before* allocating ->s_root;
there their cleanup on failure would be correct. As it is, we do iput()
on root inode, but leak the root dentry...
Oleg Nesterov [Wed, 4 Jan 2012 16:29:20 +0000 (17:29 +0100)]
ptrace: ensure JOBCTL_STOP_SIGMASK is not zero after detach
This is the temporary simple fix for 3.2, we need more changes in this
area.
1. do_signal_stop() assumes that the running untraced thread in the
stopped thread group is not possible. This was our goal but it is
not yet achieved: a stopped-but-resumed tracee can clone the running
thread which can initiate another group-stop.
Remove WARN_ON_ONCE(!current->ptrace).
2. A new thread always starts with ->jobctl = 0. If it is auto-attached
and this group is stopped, __ptrace_unlink() sets JOBCTL_STOP_PENDING
but JOBCTL_STOP_SIGMASK part is zero, this triggers WANR_ON(!signr)
in do_jobctl_trap() if another debugger attaches.
Change __ptrace_unlink() to set the artificial SIGSTOP for report.
Alternatively we could change ptrace_init_task() to copy signr from
current, but this means we can copy it for no reason and hide the
possible similar problems.
do {
ptrace(PTRACE_CONT, pid, 0, 0);
pid = waitpid(-1, NULL, 0);
} while (pid > 0);
return 1;
}
It fails because ->real_parent sees its child in EXIT_DEAD state
while the tracer is going to change the state back to EXIT_ZOMBIE
in wait_task_zombie().
The offending commit is 823b018e which moved the EXIT_DEAD check,
but in fact we should not blame it. The original code was not
correct as well because it didn't take ptrace_reparented() into
account and because we can't really trust ->ptrace.
This patch adds the additional check to close this particular
race but it doesn't solve the whole problem. We simply can't
rely on ->ptrace in this case, it can be cleared if the tracer
is multithreaded by the exiting ->parent.
I think we should kill EXIT_DEAD altogether, we should always
remove the soon-to-be-reaped child from ->children or at least
we should never do the DEAD->ZOMBIE transition. But this is too
complex for 3.2.
The call to "schedule_work()" in rtc_initialize_alarm() happens too
early, and can cause oopses at bootup
Neil Brown explains why we do it:
"If you set an alarm in the future, then shutdown and boot again after
that time, then you will end up with a timer_queue node which is in
the past.
When this happens the queue gets stuck. That entry-in-the-past won't
get removed until and interrupt happens and an interrupt won't happen
because the RTC only triggers an interrupt when the alarm is "now".
So you'll find that e.g. "hwclock" will always tell you that
'select' timed out.
So we force the interrupt work to happen at the start just in case."
and has a patch that convert it to do things in-process rather than with
the worker thread, but right now it's too late to play around with this,
so we just revert the patch that caused problems for now.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Requested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Requested-by: John Stultz <john.stultz@linaro.org> Cc: Neil Brown <neilb@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steve French [Wed, 4 Jan 2012 05:08:24 +0000 (23:08 -0600)]
[CIFS] default ntlmv2 for cifs mount delayed to 3.3
Turned out the ntlmv2 (default security authentication)
upgrade was harder to test than expected, and we ran
out of time to test against Apple and a few other servers
that we wanted to. Delay upgrade of default security
from ntlm to ntlmv2 (on mount) to 3.3. Still works
fine to specify it explicitly via "sec=ntlmv2" so this
should be fine.
Acked-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Steve French <smfrench@gmail.com>
Jeff Layton [Sun, 1 Jan 2012 15:34:39 +0000 (10:34 -0500)]
cifs: fix bad buffer length check in coalesce_t2
The current check looks to see if the RFC1002 length is larger than
CIFSMaxBufSize, and fails if it is. The buffer is actually larger than
that by MAX_CIFS_HDR_SIZE.
This bug has been around for a long time, but the fact that we used to
cap the clients MaxBufferSize at the same level as the server tended
to paper over it. Commit c974befa changed that however and caused this
bug to bite in more cases.
Reported-and-Tested-by: Konstantinos Skarlatos <k.skarlatos@gmail.com> Tested-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
It causes failures on Toshiba laptops - instead of disabling the alarm,
it actually seems to enable it on the affected laptops, resulting in
(for example) the laptop powering on automatically five minutes after
shutdown.
There's a patch for it that appears to work for at least some people,
but it's too late to play around with this, so revert for now and try
again in the next merge window.
See for example
http://bugs.debian.org/652869
Reported-and-bisected-by: Andreas Friedrich <afrie@gmx.net> (Toshiba Tecra) Reported-by: Antonio-M. Corbi Bellot <antonio.corbi@ua.es> (Toshiba Portege R500) Reported-by: Marco Santos <marco.santos@waynext.com> (Toshiba Portege Z830) Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr> (Toshiba Portege R830) Cc: Jonathan Nieder <jrnieder@gmail.com> Requested-by: John Stultz <john.stultz@linaro.org> Cc: stable@kernel.org # for the versions that applied this Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vfork parent uninterruptibly and unkillably waits for its child to
exec/exit. This wait is of unbounded length. Ignore such waits
in the hung_task detector.
Jan Kara [Tue, 3 Jan 2012 12:14:29 +0000 (13:14 +0100)]
security: Fix security_old_inode_init_security() when CONFIG_SECURITY is not set
Commit 1e39f384bb01 ("evm: fix build problems") makes the stub version
of security_old_inode_init_security() return 0 when CONFIG_SECURITY is
not set.
But that makes callers such as reiserfs_security_init() assume that
security_old_inode_init_security() has set name, value, and len
arguments properly - but security_old_inode_init_security() left them
uninitialized which then results in interesting failures.
Revert security_old_inode_init_security() to the old behavior of
returning EOPNOTSUPP since both callers (reiserfs and ocfs2) handle this
just fine.
[ Also fixed the S_PRIVATE(inode) case of the actual non-stub
security_old_inode_init_security() function to return EOPNOTSUPP
for the same reason, as pointed out by Mimi Zohar.
It got incorrectly changed to match the new function in commit fb88c2b6cbb1: "evm: fix security/security_old_init_security return
code". - Linus ]
Reported-by: Jorge Bastos <mysql.jorge@decimal.pt> Acked-by: James Morris <jmorris@namei.org> Acked-by: Mimi Zohar <zohar@us.ibm.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mwifiex: fix crash during simultaneous scan and connect
If 'iw connect' command is fired when driver is already busy in
serving 'iw scan' command, ssid specific scan operation for connect
is skipped. In this case cmd wait queue handler gets called with no
command in queue (i.e. adapter->cmd_queued = NULL).
This patch adds a NULL check in mwifiex_wait_queue_complete()
routine to fix crash observed during simultaneous scan and assoc
operations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 17030f48e31adde5b043741c91ba143f5f7db0fd
From: Rafał Miłecki <zajec5@gmail.com>
Date: Thu, 11 Aug 2011 17:16:27 +0200
Subject: [PATCH] b43: support new RX header, noticed to be used in 598.314+ fw
in PIO case.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
don't do aggregation related stuff for 'AP mode client power save
handling' if aggregation is not enabled in the driver, otherwise it
will lead to panic because those data structures won't be never
intialized in 'ath_tx_node_init' if aggregation is disabled
Oliver Hartkopp [Tue, 3 Jan 2012 08:40:28 +0000 (08:40 +0000)]
CAN MAINTAINERS update
Update the CAN MAINTAINERS section:
- point out active maintainers
- pull the CAN driver discussion away from netdev ML
- point to the new CAN web site on gitorious.org
- add CAN development git repository URL to submit patches
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> CC: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> CC: Urs Thuermann <urs.thuermann@volkswagen.de> CC: Wolfgang Grandegger <wg@grandegger.com> CC: Marc Kleine-Budde <mkl@pengutronix.de> CC: linux-can@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Tue, 3 Jan 2012 03:46:47 +0000 (03:46 +0000)]
net: fsl: fec: fix build for mx23-only kernel
If one only selects mx23-based boards, compile fails:
drivers/net/ethernet/freescale/fec.c:410:2: error: 'FEC_HASH_TABLE_HIGH' undeclared (first use in this function)
drivers/net/ethernet/freescale/fec.c:411:2: error: 'FEC_HASH_TABLE_LOW' undeclared (first use in this function)
This is because fec.h uses CONFIG_SOC_IMX28 to determine the register
layout of the core which makes sense since the MX23 does not have a fec.
However, Kconfig uses the broader ARCH_MXS symbol and this way even
makes the fec-driver default for MX23. Adapt Kconfig to use the more
precise SOC_IMX28 as well.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: David S. Miller <davem@davemloft.net> Acked-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 2 Jan 2012 05:47:57 +0000 (05:47 +0000)]
sch_qfq: fix overflow in qfq_update_start()
grp->slot_shift is between 22 and 41, so using 32bit wide variables is
probably a typo.
This could explain QFQ hangs Dave reported to me, after 2^23 packets ?
(23 = 64 - 41)
Reported-by: Dave Taht <dave.taht@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Stephen Hemminger <shemminger@vyatta.com> CC: Dave Taht <dave.taht@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: ctnetlink: fix timeout calculation
ipvs: try also real server with port 0 in backup server
skge: restore rx multicast filter on resume and after config changes
mlx4_en: nullify cq->vector field when closing completion queue
Hugh Dickins [Sat, 31 Dec 2011 19:44:01 +0000 (11:44 -0800)]
futex: Fix uninterruptible loop due to gate_area
It was found (by Sasha) that if you use a futex located in the gate
area we get stuck in an uninterruptible infinite loop, much like the
ZERO_PAGE issue.
While looking at this problem, PeterZ realized you'll get into similar
trouble when hitting any install_special_pages() mapping. And are there
still drivers setting up their own special mmaps without page->mapping,
and without special VM or pte flags to make get_user_pages fail?
In most cases, if page->mapping is NULL, we do not need to retry at all:
Linus points out that even /proc/sys/vm/drop_caches poses no problem,
because it ends up using remove_mapping(), which takes care not to
interfere when the page reference count is raised.
But there is still one case which does need a retry: if memory pressure
called shmem_writepage in between get_user_pages_fast dropping page
table lock and our acquiring page lock, then the page gets switched from
filecache to swapcache (and ->mapping set to NULL) whatever the refcount.
Fault it back in to get the page->mapping needed for key->shared.inode.
Julian Anastasov [Fri, 30 Dec 2011 05:19:02 +0000 (14:19 +0900)]
ipvs: try also real server with port 0 in backup server
We should not forget to try for real server with port 0
in the backup server when processing the sync message. We should
do it in all cases because the backup server can use different
forwarding method.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Zumbiehl [Fri, 30 Dec 2011 17:30:09 +0000 (17:30 +0000)]
skge: restore rx multicast filter on resume and after config changes
Restore skge hardware registers for multicast filtering to their
appropriate values after system resume and after hardware restarts
that are done when changing certain settings.
Signed-off-by: Florian Zumbiehl <florz@florz.de> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
which got bisected down to the stable version of this commit.
Reported-by: Jonathan Nieder <jrnieder@gmail.com> Reported-by: Phil Miller <mille121@illinois.edu> Reported-by: Philip Langdale <philipl@overt.org> Reported-by: Tim Gardner <tim.gardner@canonical.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Greg KH <gregkh@suse.de> Cc: stable@kernel.org # for stable kernels that applied the original Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 30 Dec 2011 20:13:03 +0000 (12:13 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO_wdt.c - problems with newer hardware due to SMI clearing (part 2)
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
watchdog: sp805: Fix section mismatch in ID table.
watchdog: move coh901327 state holders
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
packet: fix possible dev refcnt leak when bind fail
netem: dont call vfree() under spinlock and BH disabled
netfilter: ctnetlink: fix scheduling while atomic if helper is autoloaded
netfilter: ctnetlink: fix return value of ctnetlink_get_expect()
Andreas Schwab [Wed, 28 Dec 2011 23:57:15 +0000 (15:57 -0800)]
procfs: do not confuse jiffies with cputime64_t
Commit 2a95ea6c0d129b4 ("procfs: do not overflow get_{idle,iowait}_time
for nohz") did not take into account that one some architectures jiffies
and cputime use different units.
This causes get_idle_time() to return numbers in the wrong units, making
the idle time fields in /proc/stat wrong.
Instead of converting the usec value returned by
get_cpu_{idle,iowait}_time_us to units of jiffies, use the new function
usecs_to_cputime64 to convert it to the correct unit of cputime64_t.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "Artem S. Tashkinov" <t.artem@mailcity.com> Cc: Dave Jones <davej@redhat.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hans de Goede [Thu, 29 Dec 2011 21:09:21 +0000 (19:09 -0200)]
gspca: Fix bulk mode cameras no longer working (regression fix)
The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.
Sage Weil [Thu, 29 Dec 2011 16:05:14 +0000 (08:05 -0800)]
ceph: disable use of dcache for readdir etc.
Ceph attempts to use the dcache to satisfy negative lookups and readdir
when the entire directory contents are in cache. Disable this behavior
until lingering bugs in this code are shaken out; we'll re-enable these
hooks once things are fully stable.
Dan Williams [Thu, 29 Dec 2011 08:16:28 +0000 (09:16 +0100)]
block: fix blk_queue_end_tag()
Commit 5e081591 "block: warn if tag is greater than real_max_depth"
cleaned up blk_queue_end_tag() to warn when the tag is truly invalid
(greater than real_max_depth). However, it changed behavior in the tag <
max_depth case to not end the request. Leading to triggering of
BUG_ON(blk_queued_rq(rq)) in the request completion path:
In order to allow blk_queue_resize_tags() to shrink the tag space
blk_queue_end_tag() must always complete tags with a value less than
real_max_depth regardless of the current max_depth. The comment about
"handling the shrink case" seems to be what prompted changes in this
space, so remove it and BUG on all invalid tags (made even simpler by
Matthew's suggestion to use an unsigned compare).
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: Tao Ma <boyu.mt@taobao.com> Cc: Matthew Wilcox <matthew@wil.cx> Reported-by: Meelis Roos <mroos@ut.ee> Reported-by: Ed Nadolski <edmund.nadolski@intel.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
projects / karo-tx-linux.git / log