David S. Miller [Sun, 17 Apr 2011 23:51:36 +0000 (16:51 -0700)]
bna: Fix set-but-unused variables.
The variable 'pgoff' is set but unused in bfa_nw_ioc_fwver_get()
and bfa_ioc_download_fw().
Similarly for 'cmd_h' in bna_mbox_flush_q and the entirety of
bna_rit_mod_uninit() is unused since variables are purely set but no
action is made using them.
Same for 'bna' in bna_rit_create() and 'ret' in bna_rx_create().
Just kill them off.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 17 Apr 2011 23:23:22 +0000 (16:23 -0700)]
isdn: eicon: Fix set-but-unused variables.
The variable 'best_id' is set but unused in
diva_mnt_add_xdi_adapter(). Just kill it off.
Similarly for the variable 'CIP' in connect_req(), 'Number' in
sig_ind(), 'Info' in dtmf_confirmation() mixer_command()
fax_connect_ack_command() fax_edata_ack_command()
rtp_connect_b3_res_command() and rtp_connect_b3_res_command(), and 'a'
in mixer_indication_coefs_set(),
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 17 Apr 2011 07:10:17 +0000 (00:10 -0700)]
atm: idt77252: Fix set-but-unused variables.
Two cases here:
1) idt77252_rx_raw() really does not make any use of the
extracted PTI field of the atm header.
2) idt77252_collect_stat() only uses the register values
in code which has been compiled out by a "NOTDEF" cpp
test for more than 10 years. Just kill this NOTDEF
code entirely, but keep the register reads in case
they have side effects.
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Walter [Wed, 13 Apr 2011 21:10:57 +0000 (21:10 +0000)]
ipv6: RTA_PREFSRC support for ipv6 route source address selection
[ipv6] Add support for RTA_PREFSRC
This patch allows a user to select the preferred source address
for a specific IPv6-Route. It can be set via a netlink message
setting RTA_PREFSRC to a valid IPv6 address which must be
up on the device the route will be bound to.
Signed-off-by: Daniel Walter <dwalter@barracuda.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Walter [Wed, 13 Apr 2011 21:09:25 +0000 (21:09 +0000)]
ipv6: ignore looped-back NA while dad is running
[ipv6] Ignore looped-back NAs while in Duplicate Address Detection
If we send an unsolicited NA shortly after bringing up an
IPv6 address, the duplicate address detection algorithm
fails and the ip stays in tentative mode forever.
This is due a missing check if the NA is looped-back to us.
Signed-off-by: Daniel Walter <dwalter@barracuda.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Fri, 15 Apr 2011 06:23:45 +0000 (23:23 -0700)]
rndis_host: Quirky devices are still 'point-to-point'
My changes in commit 4d42d417be75d750b82798922b6e775915e11bce were
written some time before the introduction of FLAG_POINTTOPOINT, so
didn't include that flag in the new driver_info. Change the new
driver_info to be consistent.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David Decotigny [Wed, 13 Apr 2011 15:22:31 +0000 (15:22 +0000)]
net-bonding: Adding support for throughputs larger than 65536 Mbps
This updates the bonding driver to support v2.6.27-rc3 enhancements
(b11f8d8c aka. "ethtool: Expand ethtool_cmd.speed to 32 bits") which
allow to encode the Mbps link speed on 32-bits (Max 4 Pbps) instead of
16 (Max 65536 Mbps).
This patch also attempts to compact struct slave by reordering its
fields.
Signed-off-by: David Decotigny <decot@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Decotigny [Wed, 13 Apr 2011 15:22:30 +0000 (15:22 +0000)]
net-bonding: Fix minor/cosmetic type inconsistencies
The __get_link_speed() function returns a u16 value which was stored
in a u32 local variable. This patch uses the return value directly,
thus fixing that minor type consistency.
The 'duplex' field in struct slave being encoded on 8 bits, to be more
consistent we use a u8 integer (instead of u16) whenever we copy it to
local variables.
Signed-off-by: David Decotigny <decot@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Decotigny [Wed, 13 Apr 2011 15:22:29 +0000 (15:22 +0000)]
net-bonding: Fix minor sparse complaints
This gets rid of minor sparse complaints:
drivers/net/bonding/bond_main.c:4361:4: warning: do-while statement is not a compound statement
drivers/net/bonding/bond_main.c:243:12: warning: symbol 'bond_mode_name' was not declared. Should it be static?
Signed-off-by: David Decotigny <decot@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The phy, mac, and board information structures should be const.
Since tables contain function pointer this improves security
(at least theoretically).
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan, Bruce W [Wed, 13 Apr 2011 13:09:10 +0000 (13:09 +0000)]
ethtool: allow custom interval for physical identification
When physical identification of an adapter is done by toggling the
mechanism on and off through software utilizing the set_phys_id operation,
it is done with a fixed duration for both on and off states. Some drivers
may want to set a custom duration for the on/off intervals. This patch
changes the API so the return code from the driver's entry point when it
is called with ETHTOOL_ID_ACTIVE can specify the frequency at which to
cycle the on/off states, and updates the drivers that have already been
converted to use the new set_phys_id and use the synchronous method for
identifying an adapter.
The physical identification frequency set in the updated drivers is based
on how it was done prior to the introduction of set_phys_id.
Compile tested only. Also fixes a compiler warning in sfc.
v2: drivers do not return -EINVAL for ETHOOL_ID_ACTIVE
v3: fold patchset into single patch and cleanup per Ben's feedback
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Sathya Perla <sathya.perla@emulex.com> Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com> Cc: Ajit Khaparde <ajit.khaparde@emulex.com> Cc: Michael Chan <mchan@broadcom.com> Cc: Eilon Greenstein <eilong@broadcom.com> Cc: Divy Le Ray <divy@chelsio.com> Cc: Don Fry <pcnet32@frontier.com> Cc: Jon Mason <jdmason@kudzu.us> Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com> Cc: Steve Hodgson <shodgson@solarflare.com> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Matt Carlson <mcarlson@broadcom.com> Acked-by: Jon Mason <jdmason@kudzu.us> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 14 Apr 2011 21:49:37 +0000 (14:49 -0700)]
ipv4: Call fib_select_default() only when actually necessary.
fib_select_default() is a complete NOP, and completely pointless
to invoke, when we have no more than 1 default route installed.
And this is far and away the common case.
So remember how many prefixlen==0 routes we have in the routing
table, and elide the call when we have no more than one of those.
This cuts output route creation time by 157 cycles on Niagara2+.
In order to add the new int to fib_table, we have to correct the type
of ->tb_data[] to unsigned long, otherwise the private area will be
unaligned on 64-bit systems.
Signed-off-by: David S. Miller <davem@davemloft.net> Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
John Fastabend [Mon, 4 Apr 2011 04:29:46 +0000 (04:29 +0000)]
ixgbe: DCB, X540 devices do not respond to pause frames
DCB enabled X540 devices are not responding to pause frames
due to a missing register set that was added for these
devices that did not exist in other devices.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Mon, 4 Apr 2011 04:29:41 +0000 (04:29 +0000)]
ixgbe: DCB, misallocated packet buffer size with X540 device
The X540 device has a smaller packet buffer but the DCB configuration
never took this into account. Under stress this can result in the DMA
engine hanging and TX Unit hang occurring to reset the device. This
patch reworks the packet buffer allocation routine used for DCB on
82599 and X540 devices to account for RX packet buffer sizes.
This fixes the immediate hang. We should consolidate the various
hardware specific routines for configuring features into a single
routine. This will make it much harder to miss feature cases like
this.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Tested-by: Evan Swanson <evan.swanson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Thu, 31 Mar 2011 09:36:18 +0000 (09:36 +0000)]
ixgbe: make device_caps() generic
x540 has the same device capability word in the EEPROM as 82599.
This patch renames ixgbe_get_device_caps_82599 to
ixgbe_get_device_caps_generic, moves it to ixgbe_common.h and
sets up the function pointer for x540.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Evan Swanson <evan.swanson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Thu, 24 Mar 2011 07:06:02 +0000 (07:06 +0000)]
ixgbe: add support for new HW
Add new device ID supported by ixgbe.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Thu, 24 Mar 2011 00:57:50 +0000 (00:57 +0000)]
ixgbe: fix semaphores in eeprom routines for x540
HW can upload EEPROM content from flash while
in a middle of checksum calculation. Take NVM ownership for the whole
process of checksum update.
Call ixgbe_read_eerd_generic() and ixgbe_write_eewr_generic() directly to
avoid double take of semaphores which leads to long loading times.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Fri, 18 Mar 2011 09:32:53 +0000 (09:32 +0000)]
ixgbe: cleanup short msleep's (<20ms) to use usleep_range
Since msleep might not sleep for the desired amount when less
than 20ms use usleep_range.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Fri, 18 Mar 2011 08:18:32 +0000 (08:18 +0000)]
ixgbe: fix 82599 KR downshift coexistence with LESM FW module
Disable KR to KX4/KX downshift on 82599 backplane devices when
LESM (Link Establishment State Machine) is enabled in FW. Those
features cannot co-exist as they both manipulate the same registers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Acked-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phillip Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Thu, 17 Mar 2011 18:11:38 +0000 (18:11 +0000)]
ixgbe: update version string for Dell CEM use
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Emil Tantilov [Wed, 16 Mar 2011 01:58:20 +0000 (01:58 +0000)]
ixgbe: fix namespacecheck issue
Set ixgbe_identify_82599() as static
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 16 Mar 2011 01:55:55 +0000 (01:55 +0000)]
ixgbe: correct function number for some 82598 parts
Some 82598 parts have LAN0 disabled and LAN1 enabled and the LAN ID bits in
Device Status register report the NIC as having only LAN1 as enabled. This
causes ixgbe_set_lan_id_multi_port_pcie() to set bus->func = 1 which is
incorrect.
Force bus->func to 0 when LAN0 is disabled in the EEPROM.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Evan Swanson <evan.swanson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Sat, 12 Mar 2011 03:50:53 +0000 (03:50 +0000)]
ixgbe: DCB, further cleanups to app configuration
With the app data on the kernel dcb_app list we no longer
need to specifically handle them in ixgbe for the CEE case.
So now we can remove app handling logic and check when the
hw is configured if the app data matches the hardware
configuration in set_hw_all().
If it does not match then we can reconfigure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Thu, 24 Mar 2011 03:09:03 +0000 (03:09 +0000)]
e1000e: If ASPM L0s needs to be disabled, do it prior to enabling device
Based on a patch from Naga Chumbalkar <nagananda.chumbalkar@hp.com>:
If ASPM L0s needs to be disabled due to HW errata, do it prior to
"enabling" the device. This way if the kernel ever defaults its
aspm_policy to POLICY_POWERSAVE, then the e1000e driver will get a
chance to disable ASPM on the misbehaving device *prior* to calling
pci_enable_device_mem(). This will be useful in situations
where the BIOS indicates ASPM support on the server by clearing the
ACPI FADT "ASPM Controls" bit.
Note:
The kernel (2.6.38) currently uses the BIOS "default" as its aspm_policy.
However, Linux distros can diverge from that and set the default to
"powersave".
v2: o cleanup namespace pollution of e1000e_disable_aspm(),
o fix type and initialization of the new aspm_disable_flag in a few
functions, and
o redefine FLAG2_DISABLE_ASPM_L0S to the first unused bit in
adapter->flags2.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just move the unlock down a bit because it unlocks too
early leaving a chance for get_stats64() run in parallel
while it is still accessing the stats.
Signed-off-by: Flavio Leitner <fleitner@redhat.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 19 Mar 2011 00:31:23 +0000 (00:31 +0000)]
e1000e: PCIe link speed in GT/s, not GB/s
Correct the log message when driver loads.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Sat, 19 Mar 2011 00:27:20 +0000 (00:27 +0000)]
e1000e: convert short duration msleep() to usleep_range()
With durations less than 20ms, the jiffies or legacy timer backed msleep()
may sleep ~20ms which might not be what the caller expects. Instead, it
is recommended to use the hrtimers backed usleep_range(). For more, see
Documentation/timers/timers-howto.txt. Issues reported by checkpatch.
In addition, remove unnecessary sleep in e1000e_write_nvm_spi().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Assmann [Tue, 5 Apr 2011 04:27:15 +0000 (04:27 +0000)]
igb: introduce igb_thermal_sensor_event for sensor checking
The code for thermal sensor checking should be wrapped into a function.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Assmann [Tue, 5 Apr 2011 04:27:05 +0000 (04:27 +0000)]
igb: fix typo in igb_validate_nvm_checksum_82580
Comment spelling fix.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a revised patch that permits a shifted access to the
LAN9221 registers. More specifically:
It adds a shift parameter in the platform_data.
It introduces an ops in smsc911x_data.
A choice of access function to use at run-time.
Four new shifted access function.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 13 Apr 2011 11:05:08 +0000 (11:05 +0000)]
tg3: Add support for extended VPD blocks
In some devices, the VPD block is relocated to a different area in
NVRAM. The original location can still contain old, but still valid VPD
data. This patch changes the code to look for an extended VPD block in
NVRAM. If one is found, that block is used for all VPD operations
instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 13 Apr 2011 11:05:07 +0000 (11:05 +0000)]
tg3: Add jumbo frame loopback tests to selftest
This patch adds jumbo frame loopback test support to the ethtool
selftest.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 13 Apr 2011 11:05:06 +0000 (11:05 +0000)]
tg3: Automatically size stat/test string arrays
This patch reimplements the size preprocessor constants of the stats and
ethtool test string arrays. The size is calculated at compile time
rather than using static constants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 13 Apr 2011 11:05:05 +0000 (11:05 +0000)]
tg3: Dump registers when status block shows errors
This patch monitors the error bit of the status word within the status
block. If it is set, the driver will dump the driver state after
validating the error and then reset the chip.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 13 Apr 2011 11:05:04 +0000 (11:05 +0000)]
tg3: Provide full regdump on tx timeout
The current amount of information provided in the output of a tx timeout
is insufficient to determine a root cause. This patch replaces the
terse, four-register status output with a more complete body of
information. For PCIe devices, the full register space is dumped. For
other devices, select registers are dumped instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 13 Apr 2011 21:48:55 +0000 (14:48 -0700)]
rndis_host: Poll status before control channel where necessary
Some RNDIS devices don't respond on the control channel until polled
on the status channel. In particular, this was reported to be the
case for the 2Wire HomePortal 1000SW and for some Windows Mobile
devices.
This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk>
which is currently applied by Mandriva.
Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
amit salecha [Thu, 7 Apr 2011 01:58:42 +0000 (01:58 +0000)]
net: ethtool support to configure number of channels
Ethtool support to configure RX, TX and other channels. combined field
in struct ethtool_channels to reflect set of channel (RX, TX or other).
Other channel can be link interrupts, SR-IOV coordination etc.
ETHTOOL_GCHANNELS will report max and current number of RX channels,
max and current number of TX channels, max and current number of other channel
or max and current number of combined channel.
Number of channel can be modify upto max number of channel through
ETHTOOL_SCHANNELS command.
Ben Hutchings:
o define 'combined' and 'other' types. Most multiqueue drivers pair up RX and TX
queues so that most channels combine RX and TX work.
o Please could you use a kernel-doc comment to describe the structure.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 12 Apr 2011 23:14:21 +0000 (16:14 -0700)]
atm: iphase: Fix set-but-not-used warnings.
The "iavcc" and "iadev" cases are obvious.
The intr_status and frmr_intr cases are reading a register to clear
the chip status. This driver is pretty old and creaky, and uses
volatile pointer dereferences to do register I/O when it should be
using readl() and friends. However that it outside of the scope of
these changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 12 Apr 2011 22:58:41 +0000 (15:58 -0700)]
9p: Kill set but unused variable in 9p_client_{read,write}() and p9_client_readdir()
Fixes the following warnings:
net/9p/client.c:1305:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
net/9p/client.c:1370:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
net/9p/client.c:1769:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
Signed-off-by: David S. Miller <davem@davemloft.net>
Michał Mirosław [Tue, 12 Apr 2011 09:38:23 +0000 (09:38 +0000)]
net: bnx2x: convert to hw_features
Since ndo_fix_features callback is postponing features change when
bp->recovery_state != BNX2X_RECOVERY_DONE, netdev_update_features()
has to be called again when this condition changes. Previously,
ethtool_ops->set_flags callback returned -EBUSY in that case
(it's not possible in the new model).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
v5: - don't delay set_features, as it's rtnl_locked - same as recovery process
v4: - complete bp->rx_csum -> NETIF_F_RXCSUM conversion
- add check for failed ndo_set_features in ndo_open callback
v3: - include NETIF_F_LRO in hw_features
- don't call netdev_update_features() if bnx2x_nic_load() failed
v2: - comment in ndo_fix_features callback Signed-off-by: David S. Miller <davem@davemloft.net>
net: vlan: make non-hw-accel rx path similar to hw-accel
Now there are 2 paths for rx vlan frames. When rx-vlan-hw-accel is
enabled, skb is untagged by NIC, vlan_tci is set and the skb gets into
vlan code in __netif_receive_skb - vlan_hwaccel_do_receive.
For non-rx-vlan-hw-accel however, tagged skb goes thru whole
__netif_receive_skb, it's untagged in ptype_base hander and reinjected
This incosistency is fixed by this patch. Vlan untagging happens early in
__netif_receive_skb so the rest of code (ptype_all handlers, rx_handlers)
see the skb like it was untagged by hw.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v1->v2:
remove "inline" from vlan_core.c functions Signed-off-by: David S. Miller <davem@davemloft.net>
Allan, Bruce W [Mon, 11 Apr 2011 13:01:59 +0000 (13:01 +0000)]
ethtool: time to blink provided in seconds not jiffies
When blinking for a duration set by the user, the value specified is in
seconds but it is used as the number of jiffies in the timeout after which
the Physical ID indicator is deactivated. Fix by converting the timeout
to seconds.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log