[POWERPC] Fix irq routing on some 32-bit PowerMacs
The changes to use pci_read_irq_line() broke interrupt parsing
on some 32-bit powermacs (oops). The reason is a bit obscure.
The code to parse interrupts happens earlier now, during
pcibios_fixup() as the PCI bus is being probed. However, the
current implementation pci_device_to_OF_node() for 32-bit
powerpc relies, on machines like PowerMac which renumber PCI buses,
on a table called pci_OF_bus_map containing a map of bus numbers
between the kernel and the firmware which is setup only later.
Thus, it fails to match the device node. In addition, some of
Apple internal PCI devices lack a proper PCI_INTERRUPT_PIN, thus
preventing the fallback mapping code to work.
This patch fixes it by making pci_device_to_OF_node() 32-bit
implementation use a different algorithm that works without
using the pci_OF_bus_map thing (which I intend to deprecate
anyway). It's a bit slower but that function isn't called in
any hot path hopefully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Wed, 29 Nov 2006 11:27:42 +0000 (22:27 +1100)]
[POWERPC] Support ibm,dynamic-reconfiguration-memory nodes
For PAPR partitions with large amounts of memory, the firmware has an
alternative, more compact representation for the information about the
memory in the partition and its NUMA associativity information. This
adds the code to the kernel to parse this alternative representation.
The other part of this patch is telling the firmware that we can
handle the alternative representation. There is however a subtlety
here, because the firmware will invoke a reboot if the memory
representation we request is different from the representation that
firmware is currently using. This is because firmware can't change
the representation on the fly. Further, some firmware versions used
on POWER5+ machines have a bug where this reboot leaves the machine
with an altered value of load-base, which will prevent any kernel
booting until it is reset to the normal value (0x4000). Because of
this bug, we do NOT set fake_elf.rpanote.new_mem_def = 1, and thus we
do not request the new representation on POWER5+ and earlier machines.
We do request the new representation on POWER6, which uses the
ibm,client-architecture-support call.
Anton Blanchard [Fri, 8 Dec 2006 07:22:09 +0000 (18:22 +1100)]
[POWERPC] dont allow pSeries_probe to succeed without initialising MMU
pSeries_probe can decide that we are a pseries but then fail to
initialise the MMU. If an rtas node doesnt exist, we continually fall
out of pSeries_probe_hypertas early and never get to the MMU init code.
While pseries without RTAS is an illegal combination, the way we
currently fail is a pain to track down, and can happen if your flattened
device tree code has issues (like mine did :).
With the following patch we init the MMU, come up and print some
warnings about RTAS not existing, instead of looping on 0x400 exceptions.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Fix mmap of PCI resource with hack for X
The powerpc version of pci_resource_to_user() and associated hooks
used by /proc/bus/pci and /sys/bus/pci mmap have been broken for some
time on machines that don't have a 1:1 mapping of devices (basically
on non-PowerMacs) and have PCI devices above 32 bits.
This attempts to fix it as well as possible.
The rule is supposed to be that pci_resource_to_user() always converts
the resources back into a BAR values since that's what the /proc
interface was supposed to deal with. However, for X to work on
platforms where PCI MMIO is not mapped 1:1, it became a habit of
platforms like powerpc to pass "fixed up" values there since X expects
to be able to use values from /proc/bus/pci/devices as offsets to mmap
of /dev/mem...
So we keep that contraption here, causing also /sys/*/resource to
expose fully absolute MMIO addresses instead of BAR values, which is
ugly, but should still work as long as those are only used to calculate
alignment within a page.
X is still broken when built 32 bits on machines where PCI MMIO can be
above 32-bit space unfortunately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] cbe_thermal: Fix initialization of sysfs attribute_group
This patch adds NULL to the initialization of the attribute_groups.
The spu_attributes and ppe_attributes arrays are arrays of pointers
that need to be terminated with a NULL entry.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Scott Wood [Wed, 6 Dec 2006 21:16:24 +0000 (15:16 -0600)]
[POWERPC] qe_ic: Do a sync when masking interrupts
This patch causes a sync do be done after masking a QE interrupt, to
ensure that the masking has completed before interrupts are enabled.
This allows the masking of the cascade IRQ to be removed without causing
spurious interrupts.
The mask_and_ack function is also removed and set to the mask function,
as the two are identical.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Wed, 6 Dec 2006 18:32:20 +0000 (12:32 -0600)]
[POWERPC] EEH recovery tweaks
If one attempts to create a device driver recovery sequence that
does not depend on a hard reset of the device, but simply just
attempts to resume processing, then one discovers that the
recovery sequence implemented on powerpc is not quite right.
This patch fixes this up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Matthew Wilcox [Wed, 6 Dec 2006 05:15:05 +0000 (22:15 -0700)]
[POWERPC] Delete unused irq functions on powerpc
The ack_irq macro is unused and conflicts with James' work to template
the generic irq code. mask_irq and unmask_irq are also unused, so delete
those macros too.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Paul Mackerras <paulus@samba.org>
Roland Dreier [Wed, 6 Dec 2006 23:15:38 +0000 (15:15 -0800)]
[POWERPC] Define pci_unmap_addr() et al. when CONFIG_NOT_COHERENT_CACHE=y
The current PowerPC code makes pci_unmap_addr(), pci_unmap_addr_set(),
and friends trivial for all 32-bit kernels. This is reasonable, since
for those kernels it is true that pci_unmap_single() does not need the
DMA address from the original DMA mapping -- in fact, it is a NOP.
However, I recently tried the tg3 driver on a PowerPC 440SPe machine,
which runs a 32-bit kernel and has non-cache-coherent PCI DMA. I
found that the tg3 driver crashed in pci_dma_sync_single_for_cpu(),
since for non-coherent systems, that function must invalidate the
cache for the DMA address range requested, and therefore it does use
the address passed in. tg3 uses a DMA address it stashes away with
pci_unmap_addr_set() and retrieves with pci_unmap_addr(). Of course,
since pci_unmap_addr() is defined to (0) right now, this doesn't work.
It seems to me that the tg3 driver is using pci_unmap_addr() in a
legitimate way -- I wouldn't want to have to teach all drivers that
they should use pci_unmap_addr() if they only need the address for
unmapping functions, but if they want the pci_dma_sync functions, then
they have to store the DMA address without the helper macros.
The right fix therefore seems to be in the definition of the macros in
<asm/pci.h> -- we should use the trivial versions only for 32-bit
kernels for coherent systems, and the real versions for both 64-bit
kernels and non-coherent systems.
Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Only enable cpu hotplug via RTAS if the required firmware support is found
To support cpu hotplug on pseries we require two RTAS tokens. The cpu
hotplug machinery should only be wired up if these tokens are found in
the device tree.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Move pSeries_mach_cpu_die() into platforms/pseries/hotplug-cpu.c
Move pSeries_mach_cpu_die() into platforms/pseries/hotplug-cpu.c,
this allows rtas_stop_self() to be static so remove the prototype.
Wire up pSeries_mach_cpu_die() in the initcall, rather than statically
in setup.c, the initcall will still run prior to the cpu hotplug code
being callable, so there should be no change in behaviour.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Move rtas_stop_self() into platforms/pseries/hotplug-cpu.c
As the first step in consolidating the pseries hotplug cpu code,
create platforms/pseries/hotplug-cpu.c and move rtas_stop_self()
into it. Do the rtas token initialisation in a new initcall, rather
than rtas_initialize().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Fri, 8 Dec 2006 00:18:46 +0000 (16:18 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (55 commits)
ieee1394: sbp2: code formatting around work_struct stuff
ieee1394: nodemgr: remove a kcalloc
ieee1394: conditionally export ieee1394_bus_type
ieee1394: Consolidate driver registering
ieee1394: sbp2: convert from PCI DMA to generic DMA
ieee1394: nodemgr: spaces to tabs
ieee1394: nodemgr: fix deadlock in shutdown
ieee1394: nodemgr: remove duplicate assignment
sbp2: make 1bit bitfield unsigned
ieee1394: schedule *_oui sysfs attributes for removal
ieee1394: schedule unused symbol exports for removal
ieee1394: dv1394: schedule for feature removal
ieee1394: raw1394: defer feature removal of old isoch interface
ieee1394: ohci1394: call PMac code in shutdown only for proper machines
ieee1394: ohci1394: reformat PPC_PMAC platform code
ieee1394: ohci1394: add PPC_PMAC platform code to driver probe
ieee1394: sbp2: wrap two functions into one
ieee1394: sbp2: update comment on things to do
ieee1394: sbp2: use list_move_tail()
ieee1394: sbp2: more concise names for types and variables
...
Linus Torvalds [Thu, 7 Dec 2006 23:40:39 +0000 (15:40 -0800)]
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
Linus Torvalds [Thu, 7 Dec 2006 23:39:22 +0000 (15:39 -0800)]
Merge branch 'release' of master.kernel.org:/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of master.kernel.org:/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] replace kmalloc+memset with kzalloc
[IA64] resolve name clash by renaming is_available_memory()
[IA64] Need export for csum_ipv6_magic
[IA64] Fix DISCONTIGMEM without VIRTUAL_MEM_MAP
[PATCH] Add support for type argument in PAL_GET_PSTATE
[IA64] tidy up return value of ip_fast_csum
[IA64] implement csum_ipv6_magic for ia64.
[IA64] More Itanium PAL spec updates
[IA64] Update processor_info features
[IA64] Add se bit to Processor State Parameter structure
[IA64] Add dp bit to cache and bus check structs
[IA64] SN: Correctly update smp_affinty mask
[IA64] sparse cleanups
[IA64] IA64 Kexec/kdump
Russell King [Thu, 7 Dec 2006 23:07:26 +0000 (23:07 +0000)]
[ARM] Merge individual ARM sub-trees
Merge:
Atmel AT91RM9200 and AT91SAM9260 changes
General ARM developments
Disconfiguous memory cleanups
64-bit/32-bit division and sched_clock extension patches
EP93xx support changes
IOP support changes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jeff Garzik [Thu, 7 Dec 2006 22:56:06 +0000 (17:56 -0500)]
PCI MSI: always toggle legacy-INTx-enable bit upon MSI entry/exit
The current code (prior to this change) would disable the PCI INTx
legacy interrupt when enabling MSI... but only on PCI Express. We
should do this for all MSI devices, for safety's sake.
Nicolas Pitre [Thu, 7 Dec 2006 18:09:20 +0000 (19:09 +0100)]
[ARM] 3983/2: remove unused argument to __bug()
It appears that include/asm-arm/bug.h requires include/linux/stddef.h
for the definition of NULL. It seems that stddef.h was always included
indirectly in most cases, and that issue was properly fixed a while ago.
Because the third argument to __bug() is never used anyway, RMK suggested
getting rid of it entirely instead of readding #include <linux/stddef.h>
which this patch does.
Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Thu, 7 Dec 2006 19:47:58 +0000 (20:47 +0100)]
[ARM] 3999/1: RX3715: suspend to RAM support
The RX3715 is similar to the H1940 in the way
that suspend to RAM works, so we can use most
of the extant support for the H1940 with only
a few modifictions
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stefan Richter [Fri, 24 Nov 2006 19:19:09 +0000 (20:19 +0100)]
ieee1394: conditionally export ieee1394_bus_type
Follow-up to patch "Consolidate driver registering":
Since I plan the lifetime of Linux 2.6.20 to be the deprecation phase
of CONFIG_IEEE1394_EXPORT_FULL_API, it seems fair to keep all previously
exported symbols available with this option until this phase is over.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Ben Collins [Thu, 23 Nov 2006 18:59:48 +0000 (13:59 -0500)]
ieee1394: Consolidate driver registering
This patch consolidates some bookkeeping for driver registering. It
closely models what pci_register_driver() does. The main addition is
that the owner of the driver is set, so we get a proper symlink
for /sys/bus/ieee1394/driver/*/module.
Also moves setting of name and bus type into nodemgr. Because of this,
we can remove the EXPORT_SYMBOL for ieee1394_bus_type, since it's now
only used in ieee1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Wed, 22 Nov 2006 20:09:42 +0000 (21:09 +0100)]
ieee1394: nodemgr: fix deadlock in shutdown
If "modprobe ohci1394" was quickly followed by "modprobe -r ohci1394",
say with 1 second pause in between, the modprobe -r got stuck in
uninterruptible sleep in kthread_stop. At the same time the knodemgrd
slept uninterruptibly in bus_rescan_devices_helper. That's because
driver_detach took the semaphore of the PCI device and
bus_rescan_devices_helper wanted to take the semaphore of the FireWire
host device's parent, which is the same semaphore. This was a regression
since Linux 2.6.16, commit bf74ad5bc41727d5f2f1c6bedb2c1fac394de731,
"Hold the device's parent's lock during probe and remove".
The fix (or workaround) adds a dummy driver to the hpsb_host device. Now
bus_rescan_devices_helper won't scan the host device anymore. This
doesn't hurt since we have no drivers which will bind to these devices
and it is unlikely that there will ever be such a driver. The dummy
driver is befittingly presented as a representation of ieee1394 itself.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=6706 Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 19 Nov 2006 22:04:31 +0000 (23:04 +0100)]
ieee1394: schedule *_oui sysfs attributes for removal
There is no manpower available to reform oui.db into a library for use
in more kernel subsystems. The low ratio of usefulness to size and the
occasional need to update oui.db from IEEE's official list suggest to
drop oui.db. I plan to make a userspace script available which
translates the remaining numeric sysfs attributes to names of
organizations.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 19 Nov 2006 23:05:05 +0000 (00:05 +0100)]
ieee1394: raw1394: defer feature removal of old isoch interface
Known to be affected:
- libdc1394: prefers video1394 for now, old-style raw1394 support might
be dropped eventually
- OpenH323 PWLib, AVC video input module: uses libraw1394's old API
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Fri, 10 Nov 2006 23:22:35 +0000 (00:22 +0100)]
ieee1394: ohci1394: add PPC_PMAC platform code to driver probe
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=7431
iBook G3 threw a machine check exception and put the display backlight
to full brightness after ohci1394 was unloaded and reloaded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 2 Nov 2006 20:16:08 +0000 (21:16 +0100)]
ieee1394: sbp2: more concise names for types and variables
"struct scsi_id_instance_data" represents a logical unit.
Rename it to "struct sbp2_lu", and "scsi_id" to "lu".
Rename some other variables too.
Wrap almost all lines after at most 80 columns.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 2 Nov 2006 20:16:08 +0000 (21:16 +0100)]
ieee1394: sbp2: consolidate log levels
Replace some calls to SBP2_ERR and SBP2_WARN by SBP2_INFO.
Remove logging macros SBP2_NOTICE and SBP2_WARN.
Remove direct usage of HPSB_ logging macros.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 2 Nov 2006 20:16:08 +0000 (21:16 +0100)]
ieee1394: sbp2: remove duplicate code
The same case is handled further below in sbp2scsi_complete_command.
Note, the second version behaves slightly different but looks
preferable. It's an extremely unlikely case by the way.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 2 Nov 2006 20:16:08 +0000 (21:16 +0100)]
ieee1394: sbp2: clean up function declarations
Remove unnecessary function prototypes.
Remove variable names from function prototypes.
Move declarations from sbp2.h to sbp2.c.
Move definitions of driver templates together near the top of sbp2.c.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 2 Nov 2006 20:16:08 +0000 (21:16 +0100)]
ieee1394: sbp2: remove irritating log message
The queue depth can be read from /sys/bus/scsi/devices/*/queue_depth,
so don't log it. And the hint about speed improvements is misleading,
at least under current kernels. If serialization is switched off, read
performance is typically increased by less than 10%. (I did not test
write performance recently.) On the other hand, serialize_io=0 is not
yet safe due to some implementation issues that are not trivial to fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 29 Oct 2006 18:58:25 +0000 (19:58 +0100)]
ieee1394: ohci1394: proper log messages in suspend and resume
- correct thinko in one of my last commits: cannot use PRINT macro with
ohci == NULL
- add log messages on ohci == NULL and on pci_enable_device != 0
- update log macros from patch "revert fail on error in suspend" to use
PRINT and DBGMSG where possible
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 29 Oct 2006 18:52:49 +0000 (19:52 +0100)]
ieee1394: ohci1394: revert fail on error in suspend
Some errors during preparation for suspended state can be skipped with a
warning instead of a failure of the whole suspend transition, notably an
error in pci_set_power_state.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 22 Oct 2006 14:16:27 +0000 (16:16 +0200)]
ieee1394: nodemgr: revise semaphore protection of driver core data
- The list "struct class.children" is supposed to be protected by
class.sem, not by class.subsys.rwsem.
- nodemgr_remove_uds() iterated over nodemgr_ud_class.children without
proper protection. This was never observed as a bug since the code
is usually only accessed by knodemgrd. All knodemgrds are currently
globally serialized. But userspace can trigger this code too by
writing to /sys/bus/ieee1394/destroy_node.
- Clean up access to the FireWire bus type's subsys.rwsem: Access it
uniformly via ieee1394_bus_type. Shrink rwsem protected regions
where possible. Expand them where necessary. The latter wasn't a
problem so far because knodemgr is globally serialized.
This should harden the interaction of ieee1394 with sysfs and lay ground
for deserialized operation of multiple knodemgrds and for implementation
of subthreads for parallelized scanning and probing.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Daniel Drake [Fri, 20 Oct 2006 13:56:01 +0000 (14:56 +0100)]
video1394: remove BKL contention
video1394 does not need to take the BKL. The data structures shared between
file_operations and interrupts are already protected through context-specific
spinlocks.
The only other danger is video1394_release() being called during another
operation, however this cannot happen because release is only ever invoked
when the last thread has closed the fd.
Signed-off-by: Daniel Drake <ddrake@brontes3d.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Daniel Drake [Wed, 18 Oct 2006 20:37:14 +0000 (21:37 +0100)]
video1394: small optimizations to frame retrieval codepath
Add some GCC branch prediction optimizations to unlikely error/safety
conditions in the ioctl handling code commonly called during an application's
capture loop.
Signed-off-by: Daniel Drake <ddrake@brontes3d.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Bernhard Kaindl [Wed, 6 Sep 2006 12:58:30 +0000 (14:58 +0200)]
ohci1394: steps to implement suspend/resume
I did a quick shot on what I described and the appended patch
does the first thing needed for working suspend/resume
in ohci1394 which is HW de- and re-initialisation.
It works with suspend2disk on my Ricoh R5C552 IEEE 1394 Controller
with the 2.6.17 kernel to the extent that if I call dvgrab --interactive
after suspend2disk without unloading ohci1394, it does not lock up
dvgrab with 100% CPU but properly connects to the camera, given
that I first unplug and plug the camera after coming back from
suspend.
I guess that could be fixed by forcing a bus reset in the resume
function.
I cannot test suspend to RAM here at the moment and should
follow the guidelines in Documentation/power/pci.txt also,
so this is rather a quick report than a finished patch and
there are some rough edges:
However, with this patch, I have to unload at least some in-kernel
users of ohci1394 like dv1394 or video1394 before suspending.
Not doing that caused an Oops and a bad tasklet error, probably from
not handling ISO tasklets during suspend/resume properly.
Maybe these can be temporarily cleared or unregistered and
re-registered for suspend/resume with help from the other
layers or from the highlevel 1394 core, but I do not really
know what these do.
But this patch provides a useful base to start from and is
already of much help for people which do not need dv1394
and video1394 or can unload them at least during suspend.
I cannot test function with sbp2 at the moment, but raw1394
seems to work fine.
Signed-off-by: Bernhard Kaindl <bk@fsfe.org>
Update 1: merge with previous two ohci1394 suspend/resume patches
Update 2: version for application on top of Linux 2.6.19-rc4
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Mon, 11 Sep 2006 18:17:14 +0000 (20:17 +0200)]
ieee1394: sbp2: slightly reorder sbp2scsi_abort
Put the target's fetch agent into reset state before the underlying ORB
DMA is unmapped and the ->done handler is called. It is highly unlikely
but the target could access that ORB right before sbp2 sends the reset
request.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 7 Sep 2006 23:30:04 +0000 (01:30 +0200)]
ieee1394: remove unused struct member from highlevel API
struct hpsb_highlevel's struct module *owner is neither used by the IEEE
1394 core nor set by any of the in-tree drivers or the two out-of-tree
highlevel drivers I know about (dfg1394, mem1394) --- nor is this member
documented. An unscheduled removal seems acceptable.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
projects / linux-beck.git / log