Modeset path seems to conflict sometimes with the memory management
leading to kernel deadlock. This move modesetting reset after GPU
acceleration reset.
Redirect invalid memory accesses to the default page
instead of locking up the memory controller. Also
enable the invalid memory access interrupts and
start spamming system log with it.
v2 (agd5f): fix up against 2 level PT changes
Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma_pte_free_pagetable() function will only free a page table page
if it is asked to free the *entire* 2MiB range that it covers. So if a
page table page was used for one or more small mappings, it's likely to
end up still present in the page tables... but with no valid PTEs.
This was fine when we'd only be repopulating it with 4KiB PTEs anyway
but the same virtual address range can end up being reused for a
*large-page* mapping. And in that case were were trying to insert the
large page into the second-level page table, and getting a complaint
from the sanity check in __domain_mapping() because there was already a
corresponding entry. This was *relatively* harmless; it led to a memory
leak of the old page table page, but no other ill-effects.
Fix it by calling dma_pte_clear_range (hopefully redundant) and
dma_pte_free_pagetable() before setting up the new large page.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Tested-by: Ravi Murty <Ravi.Murty@intel.com> Tested-by: Sudeep Dutt <sudeep.dutt@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device IDs for WiMAX function of Intel 6150 cards.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users of jffs2_do_reserve_space() expect they still held
erase_completion_lock after call to it. But there is a path
where jffs2_do_reserve_space() leaves erase_completion_lock unlocked.
The patch fixes it.
Found by Linux Driver Verification project (linuxtesting.org).
If the rpc_task exits while holding the socket write lock before it has
allocated an rpc slot, then the usual mechanism for releasing the write
lock in xprt_release() is defeated.
The problem occurs if the call to xprt_lock_write() initially fails, so
that the rpc_task is put on the xprt->sending wait queue. If the task
exits after being assigned the lock by __xprt_lock_write_func, but
before it has retried the call to xprt_lock_and_alloc_slot(), then
it calls xprt_release() while holding the write lock, but will
immediately exit due to the test for task->tk_rqstp != NULL.
This patch ensures that we free the rpc_task after the cleanup callbacks
are done in order to avoid a deadlock problem that can be triggered if
the callback needs to wait for another workqueue item to complete.
Commit bbf43dc888833ac0539e437dbaeb28bfd4fbab9f "sunrpc/cache.h: replace
simple_strtoul" introduced new range-checking which could cause get_int
to fail on unsigned integers too large to be represented as an int.
We could parse them as unsigned instead--but it turns out svcgssd is
actually passing down "-1" in some cases. Which is perhaps stupid, but
there's nothing we can do about it now.
So just revert back to the previous "sloppy" behavior that accepts
either representation.
Reported-by: Sven Geggus <lists@fuchsschwanzdomain.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are SUNRPC clients, which program doesn't have pipe_dir_name. These
clients can be skipped on PipeFS events, because nothing have to be created or
destroyed. But instead of breaking in case of such a client was found, search
for suitable client over clients list have to be continued. Otherwise some
clients could not be covered by PipeFS event handler.
rpc_kill_sb() must defer calling put_net() until after the notifier
has been called, since most (all?) of the notifier callbacks assume
that sb->s_fs_info points to a valid net namespace. It also must not
call put_net() if the call to rpc_fill_super was unsuccessful.
The i2c handling in tfp410 driver, which handles converting parallel RGB
to DVI, was changed in 958f2717b84e88bf833d996997fda8f73276f2af
(OMAPDSS: TFP410: pdata rewrite). The patch changed what value the
driver considers as invalid/undefined. Before the patch, 0 was the
invalid value, but as 0 is a valid bus number, the patch changed this to
-1.
However, the fact was missed that many board files do not define the bus
number at all, thus it's left to 0. This causes the driver to fail to
get the i2c bus, exiting from the driver's probe with an error, meaning
that the DVI output does not work for those boards.
This patch fixes the issue by changing the i2c_bus number field in the
driver's platform data from u16 to int, and setting the bus number to -1
in the board files for the boards that did not define the bus. The
exception is devkit8000, for which the bus is set to 1, which is the
correct bus for that board.
The bug exists in v3.5+ kernels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reported-by: Thomas Weber <thomas@tomweber.eu> Cc: Thomas Weber <thomas@tomweber.eu> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1f2bfbd00e466ff3489b2ca5cc75b1cccd14c123 "kbuild:
link of vmlinux moved to a script" make clean with M=<dir>
argument (so cleaning external module) removes vmlinux,
System.map and couple of other files from the *main* kernel
build directory! This not what was happening before and almost
certainly not what one would expect.
This patch moves makes the clean target of the script called
only when !KBUILD_EXTMOD.
Signed-off-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It could happen (1 out of 100 times) that NAND did not start up
correctly after warm rebooting, so the kernel could not find the UBI or
DMA timed out due to a stalled BCH. When resetting BCH together with
GPMI, the issue could not be observed anymore (after 10000+ reboots). We
probably need the consistent state already before sending any command to
NAND, even when no ECC is needed. I chose to keep the extra reset for
BCH when changing the flash layout to be on the safe side.
Initialising ecc.strength before the call to nand_scan() fixes this.
Signed-off-by: Nathan Williams <nathan@traverse.com.au> Acked-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fa77dcfafeaa introduces block bitmap checksum calculation into
ext4_new_inode() in the case that block group was uninitialized.
However we brelse() the bitmap buffer before we attempt to checksum it
so we have no guarantee that the buffer is still there.
Fix this by releasing the buffer after the possible checksum
computation.
Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Acked-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older gcc (< 4.4) doesn't like files starting with Unicode BOMs:
include/linux/mfd/da9055/core.h:1: error: stray ‘\357’ in program
include/linux/mfd/da9055/core.h:1: error: stray ‘\273’ in program
include/linux/mfd/da9055/core.h:1: error: stray ‘\277’ in program
include/linux/mfd/da9055/pdata.h:1: error: stray ‘\357’ in program
include/linux/mfd/da9055/pdata.h:1: error: stray ‘\273’ in program
include/linux/mfd/da9055/pdata.h:1: error: stray ‘\277’ in program
include/linux/mfd/da9055/reg.h:1: error: stray ‘\357’ in program
include/linux/mfd/da9055/reg.h:1: error: stray ‘\273’ in program
include/linux/mfd/da9055/reg.h:1: error: stray ‘\277’ in program
Remove the BOMs, the rest of the files is plain ASCII anyway.
Output of "file" before:
include/linux/mfd/da9055/core.h: UTF-8 Unicode (with BOM) C program text
include/linux/mfd/da9055/pdata.h: UTF-8 Unicode (with BOM) C program text
include/linux/mfd/da9055/reg.h: UTF-8 Unicode (with BOM) C program text
Output of "file" after:
include/linux/mfd/da9055/core.h: ASCII C program text
include/linux/mfd/da9055/pdata.h: ASCII C program text
include/linux/mfd/da9055/reg.h: ASCII C program text
mfd_remove_devices would iterate over all devices sharing a parent with
an mfd device regardless of whether they were allocated by the mfd core
or not. This especially caused problems when the device structure was
not contained within a platform_device, because to_platform_device is
used on each device pointer.
This patch defines a device_type for mfd devices and checks this is
present from mfd_remove_devices_fn before processing the device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Tested-by: Peter Tyser <ptyser@xes-inc.com> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is supported identically to the previous revisions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the TPG memory is allocated successfully, but we fail further along
in the function, a dangling pointer to freed memory is left in the TPort
structure. This is mostly harmless, but does prevent re-trying the
operation without first removing the TPort altogether.
Reported-by: Chen Gang <gang.chen@asianux.com> Signed-off-by: Chris Boot <bootc@bootc.net> Cc: Andy Grover <agrover@redhat.com> Cc: Nicholas A. Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lockdep warning below is in theory correct but it will be in really weird
rare situation that ends up that deadlock since the tcm fc session is hashed
based the rport id. Nonetheless, the complaining below is about rcu callback
that does the transport_deregister_session() is happening in softirq, where
transport_register_session() that happens earlier is not. This triggers the
lockdep warning below. So, just fix this to make lockdep happy by disabling
the soft irq before calling transport_register_session() in ft_prli.
BTW, this was found in FCoE VN2VN over two VMs, couple of create and destroy
would get this triggered.
v1: was enforcing register to be in softirq context which was not righ. See,
http://www.spinics.net/lists/target-devel/msg03614.html
v2: following comments from Roland&Nick (thanks), it seems we don't have to
do transport_deregister_session() in rcu callback, so move it into ft_sess_free()
but still do kfree() of the corresponding ft_sess struct in rcu callback to
make sure the ft_sess is not freed till the rcu callback.
...
[ 1328.370592] scsi2 : FCoE Driver
[ 1328.383429] fcoe: No FDMI support.
[ 1328.384509] host2: libfc: Link up on port (000000)
[ 1328.934229] host2: Assigned Port ID 00a292
[ 1357.232132] host2: rport 00a393: Remove port
[ 1357.232568] host2: rport 00a393: Port sending LOGO from Ready state
[ 1357.233692] host2: rport 00a393: Delete port
[ 1357.234472] host2: rport 00a393: work event 3
[ 1357.234969] host2: rport 00a393: callback ev 3
[ 1357.235979] host2: rport 00a393: Received a LOGO response closed
[ 1357.236706] host2: rport 00a393: work delete
[ 1357.237481]
[ 1357.237631] =================================
[ 1357.238064] [ INFO: inconsistent lock state ]
[ 1357.238450] 3.7.0-rc7-yikvm+ #3 Tainted: G O
[ 1357.238450] ---------------------------------
[ 1357.238450] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 1357.238450] ksoftirqd/0/3 [HC0[0]:SC1[1]:HE0:SE0] takes:
[ 1357.238450] (&(&se_tpg->session_lock)->rlock){+.?...}, at: [<ffffffffa01eacd4>] transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] {SOFTIRQ-ON-W} state was registered at:
[ 1357.238450] [<ffffffff810834f5>] mark_held_locks+0x6d/0x95
[ 1357.238450] [<ffffffff8108364a>] trace_hardirqs_on_caller+0x12d/0x197
[ 1357.238450] [<ffffffff810836c1>] trace_hardirqs_on+0xd/0xf
[ 1357.238450] [<ffffffff8149caba>] _raw_spin_unlock_irq+0x2d/0x45
[ 1357.238450] [<ffffffffa01e8d10>] __transport_register_session+0xb8/0x122 [target_core_mod]
[ 1357.238450] [<ffffffffa01e8dbe>] transport_register_session+0x44/0x5a [target_core_mod]
[ 1357.238450] [<ffffffffa018e32c>] ft_prli+0x1e3/0x275 [tcm_fc]
[ 1357.238450] [<ffffffffa0160e8d>] fc_rport_recv_req+0x95e/0xdc5 [libfc]
[ 1357.238450] [<ffffffffa015be88>] fc_lport_recv_els_req+0xc4/0xd5 [libfc]
[ 1357.238450] [<ffffffffa015c778>] fc_lport_recv_req+0x12f/0x18f [libfc]
[ 1357.238450] [<ffffffffa015a6d7>] fc_exch_recv+0x8ba/0x981 [libfc]
[ 1357.238450] [<ffffffffa0176d7a>] fcoe_percpu_receive_thread+0x47a/0x4e2 [fcoe]
[ 1357.238450] [<ffffffff810549f1>] kthread+0xb1/0xb9
[ 1357.238450] [<ffffffff814a40ec>] ret_from_fork+0x7c/0xb0
[ 1357.238450] irq event stamp: 275411
[ 1357.238450] hardirqs last enabled at (275410): [<ffffffff810bb6a0>] rcu_process_callbacks+0x229/0x42a
[ 1357.238450] hardirqs last disabled at (275411): [<ffffffff8149c2f7>] _raw_spin_lock_irqsave+0x22/0x8e
[ 1357.238450] softirqs last enabled at (275394): [<ffffffff8103d669>] __do_softirq+0x246/0x26f
[ 1357.238450] softirqs last disabled at (275399): [<ffffffff8103d6bb>] run_ksoftirqd+0x29/0x62
[ 1357.238450]
[ 1357.238450] other info that might help us debug this:
[ 1357.238450] Possible unsafe locking scenario:
[ 1357.238450]
[ 1357.238450] CPU0
[ 1357.238450] ----
[ 1357.238450] lock(&(&se_tpg->session_lock)->rlock);
[ 1357.238450] <Interrupt>
[ 1357.238450] lock(&(&se_tpg->session_lock)->rlock);
[ 1357.238450]
[ 1357.238450] *** DEADLOCK ***
[ 1357.238450]
[ 1357.238450] no locks held by ksoftirqd/0/3.
[ 1357.238450]
[ 1357.238450] stack backtrace:
[ 1357.238450] Pid: 3, comm: ksoftirqd/0 Tainted: G O 3.7.0-rc7-yikvm+ #3
[ 1357.238450] Call Trace:
[ 1357.238450] [<ffffffff8149399a>] print_usage_bug+0x1f5/0x206
[ 1357.238450] [<ffffffff8100da59>] ? save_stack_trace+0x2c/0x49
[ 1357.238450] [<ffffffff81082aae>] ? print_irq_inversion_bug.part.14+0x1ae/0x1ae
[ 1357.238450] [<ffffffff81083336>] mark_lock+0x106/0x258
[ 1357.238450] [<ffffffff81084e34>] __lock_acquire+0x2e7/0xe53
[ 1357.238450] [<ffffffff8102903d>] ? pvclock_clocksource_read+0x48/0xb4
[ 1357.238450] [<ffffffff810ba6a3>] ? rcu_process_gp_end+0xc0/0xc9
[ 1357.238450] [<ffffffffa01eacd4>] ? transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] [<ffffffff81085ef1>] lock_acquire+0x119/0x143
[ 1357.238450] [<ffffffffa01eacd4>] ? transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] [<ffffffff8149c329>] _raw_spin_lock_irqsave+0x54/0x8e
[ 1357.238450] [<ffffffffa01eacd4>] ? transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] [<ffffffffa01eacd4>] transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] [<ffffffff810bb6a0>] ? rcu_process_callbacks+0x229/0x42a
[ 1357.238450] [<ffffffffa018ddc5>] ft_sess_rcu_free+0x17/0x24 [tcm_fc]
[ 1357.238450] [<ffffffffa018ddae>] ? ft_sess_free+0x1b/0x1b [tcm_fc]
[ 1357.238450] [<ffffffff810bb6d7>] rcu_process_callbacks+0x260/0x42a
[ 1357.238450] [<ffffffff8103d55d>] __do_softirq+0x13a/0x26f
[ 1357.238450] [<ffffffff8149b34e>] ? __schedule+0x65f/0x68e
[ 1357.238450] [<ffffffff8103d6bb>] run_ksoftirqd+0x29/0x62
[ 1357.238450] [<ffffffff8105c83c>] smpboot_thread_fn+0x1a5/0x1aa
[ 1357.238450] [<ffffffff8105c697>] ? smpboot_unregister_percpu_thread+0x47/0x47
[ 1357.238450] [<ffffffff810549f1>] kthread+0xb1/0xb9
[ 1357.238450] [<ffffffff8149b49d>] ? wait_for_common+0xbb/0x10a
[ 1357.238450] [<ffffffff81054940>] ? __init_kthread_worker+0x59/0x59
[ 1357.238450] [<ffffffff814a40ec>] ret_from_fork+0x7c/0xb0
[ 1357.238450] [<ffffffff81054940>] ? __init_kthread_worker+0x59/0x59
[ 1417.440099] rport-2:0-0: blocked FC remote port time out: removing rport
Signed-off-by: Yi Zou <yi.zou@intel.com> Cc: Open-FCoE <devel@open-fcoe.org> Cc: Nicholas A. Bellinger <nab@risingtidesystems.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes vectored file I/O to use kmap + kunmap when mapping
incoming SGL memory -> struct iovec in order to properly support 32-bit
highmem configurations. This is because an extra bounce buffer may be
required when processing scatterlist pages allocated with GFP_KERNEL.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ata_device->dma_mode's initial value is zero, which is not a valid dma
mode, but ata_dma_enabled will return true for this value. This patch
sets dma_mode to 0xff in reset function, so that ata_dma_enabled will
not return true for this case, or it will cause problem for pata_acpi.
The corrsponding bugzilla page is at:
https://bugzilla.kernel.org/show_bug.cgi?id=49151
Reported-by: Phillip Wood <phillip.wood@dunelm.org.uk> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Tested-by: Szymon Janc <szymon@janc.net.pl> Tested-by: Dutra Julio <dutra.julio@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
record_size / console_size / ftrace_size can be 0 (this is how you disable
the feature), but rounddown_pow_of_two(0) is undefined. As suggested by
Kees Cook, use !is_power_of_2() as a condition to call
rounddown_pow_of_two and avoid its undefined behavior on the value 0. This
issue has been present since commit 1894a253 (ramoops: Move to
fs/pstore/ram.c).
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Florian Fainelli <ffainelli@freebox.fr> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lockdep warns about taking a hard-irq-unsafe lock (sriov->id_map_lock)
inside a hard-irq-safe lock (sriov->going_down_lock).
Since id_map_lock is never taken in the interrupt context, we can
simply reverse the order of taking the two spinlocks, thus avoiding
the warning and the depencency.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SN06 in some cases returns an Integer instead of a buffer. While the
code handling the return value was trying to cope with the difference,
the memcpy call was not making any difference between the two types of
acpi_object union. This regression was introduced in 3.5.
While there also rework the return value logic to improve readability.
sata_promise's pdc_hard_reset_port() needs to serialize because it
flips a port-specific bit in controller register that's shared by
all ports. The code takes the ata host lock for this, but that's
broken because an interrupt may arrive on our irq during the hard
reset sequence, and that too will take the ata host lock. With
lockdep enabled a big nasty warning is seen.
Fixed by adding private state to the ata host structure, containing
a second lock used only for serializing the hard reset sequences.
This eliminated the lockdep warnings both on my test rig and on
the original reporter's machine.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Tested-by: Adko Branil <adkobranil@yahoo.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Search through the list of pending commands on the session list to find
the command the initiator is actually aborting, so that we can pass the
correct LUN to the core TMR handling code.
(nab: Allow abort requests to work to LUN=0 with mainline target code)
Signed-off-by: Steve Hodgson <steve@purestorage.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function iscsit_build_conn_drop_async_message() is called
from iscsit_close_connection() with spin lock 'sess->conn_lock'
held, so we should use GFP_ATOMIC instead of GFP_KERNEL.
There are some cases, for example when the initiator sends an
out-of-bounds ErrorRecoveryLevel value, where the iSCSI target
terminates the connection without sending back any error. Audit the
login path and add appropriate iscsit_tx_login_rsp() calls to make
sure this doesn't happen.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug in the hanlding of initiator provided ExpStatSN and
individual iscsi_cmd->stat_sn comparision during iscsi_conn->stat_sn
wrap-around within iscsit_ack_from_expstatsn() code.
This bug would manifest itself as iscsi_cmd descriptors not being Acked
by a lower ExpStatSn, causing them to be leaked until an iSCSI connection
or session reinstatement event occurs to release all commands.
Also fix up two other uses of incorrect CmdSN SNA comparison to use wrapper
usage from include/scsi/iscsi_proto.h.
Signed-off-by: Steve Hodgson <steve@purestorage.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the qla2xxx driver loses access to multiple, remote ports, there is a race
condition which can occur which will keep the request stuck on a scsi request
queue indefinitely.
This bad state occurred do to a race condition with how the FCPORT_UPDATE_NEEDED
bit is set in qla2x00_schedule_rport_del(), and how it is cleared in
qla2x00_do_dpc(). The problem port has its drport pointer set, but it has never
been processed by the driver to inform the fc transport that the port has been
lost. qla2x00_schedule_rport_del() sets drport, and then sets the
FCPORT_UPDATE_NEEDED bit. In qla2x00_do_dpc(), the port lists are walked and
any drport pointer is handled and the fc transport informed of the port loss,
then the FCPORT_UPDATE_NEEDED bit is cleared. This leaves a race where the
dpc thread is processing one port removal, another port removal is marked
with a call to qla2x00_schedule_rport_del(), and the dpc thread clears the
bit for both removals, even though only the first removal was actually
handled. Until another event occurs to set FCPORT_UPDATE_NEEDED, the later
port removal is never finished and qla2xxx stays in a bad state which causes
requests to become stuck on request queues.
This patch updates the driver to test and clear FCPORT_UPDATE_NEEDED
atomically. This ensures the port state changes are processed and not lost.
Signed-off-by: David Jeffery <djeffery@redhat.com> Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FC transport on receiving bsg_job submission failure, calls bsg_job->job_done()
and sets the bsg_job->reply->result the returned value. In contrast, when the
success code (0) is returned fc transport doesn't call bsg_job->job_done() and
doesn't populate bsg_job->reply->result.
Signed-off-by: Steve Hodgson <steve@purestorage.com> Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com> Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
store_host_reset() has tried to re-invent the wheel to compare sysfs strings.
Unfortunately it did so poorly and never bothered to check the input from
userspace before overwriting stack with it, so something simple as:
This patch fix the abnormal ramp delay setting.
The shift operation was wrong.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
and the kernel is booted with nmi_watchdog=1 (default)
Running laptop-mode-tools and disconnecting/connecting AC power will
cause this to trigger, making it a common failure scenario on laptops.
Instead of bailing out of watchdog_disable() when !watchdog_enabled we
can initialize the hrtimer regardless of watchdog_enabled status. This
makes it safe to call watchdog_disable() in the nmi_watchdog=0 case,
without the negative effect on the enabled => disabled => enabled case.
All these tests pass with this patch:
- nmi_watchdog=1
echo 0 > /proc/sys/kernel/nmi_watchdog
echo 1 > /proc/sys/kernel/nmi_watchdog
This patch fixes both the transmit and receive portion of sending
fragmented mutlicast and broadcast packets.
The transmit section was broken because the offset for INTFRAG and
LASTFRAG packets were just miscalculated by IEEE1394_GASP_HDR_SIZE (which
was reserved with skb_push() in fwnet_send_packet).
The receive section was broken because in fwnet_incoming_packet is a call
to fwnet_peer_find_by_node_id(). Called with generation == -1 it will
not find a peer and the partial datagrams are associated to a peer.
[Stefan R: The fix to use context->card->generation is not perfect.
It relies on the IR tasklet which processes packets from the prior bus
generation to run before the self-ID-complete worklet which sets the
current card generation. Alas, there is no simple way of a race-free
implementation. Let's do it this way for now.]
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean reported that as of 3.7, his AR9170 device no longer works
because the driver fails during initialization. He noted this
is due to:
"In carl9170/fw.c, ar->hw->wiphy is tagged with
NL80211_IFTYPE_MESH_POINT support if the firmware has Content
after Beacon Queuing. This is both in interface_modes and the
only iface_combinations entry.
If CONFIG_MAC80211_MESH is not set, ieee80211_register_hw
removes NL80211_IFTYPE_MESH_POINT from interface_modes, but
not iface_combinations.
wiphy_register then checks to see if every interface type in
every interface combination is in interface_modes.
NL80211_IFTYPE_MESH_POINT was removed, so you get a WARN_ON
warning and it returns -EINVAL, giving up."
Unfortunately, the iface_combination (types) feature bitmap
in ieee80211_iface_limit is part of a const member in the
ieee80211_iface_combination struct. Hence, the MESH_POINT
feature flag can't be masked by wiphy_register in the
same way as interface_modes in ieee80211_register_hw.
Reported-by: Sean Patrick Santos <quantheory@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Tested-by: Sean Patrick Santos <quantheory@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f0425beda4d404a6e751439b562100b902ba9c98 "mac80211: retry sending
failed BAR frames later instead of tearing down aggr" caused regression
on rt2x00 hardware (connection hangs). This regression was fixed by
commit be03d4a45c09ee5100d3aaaedd087f19bc20d01 "rt2x00: Don't let
mac80211 send a BAR when an AMPDU subframe fails". But the latter
commit caused yet another problem reported in
https://bugzilla.kernel.org/show_bug.cgi?id=42828#c22
After long discussion in this thread:
http://mid.gmane.org/20121018075615.GA18212@redhat.com
and testing various alternative solutions, which failed on one or other
setup, we have no other good fix for the issues like just revert both
mentioned earlier commits.
To do not affect other hardware which benefit from commit f0425beda4d404a6e751439b562100b902ba9c98, instead of reverting it,
introduce flag that when used will restore mac80211 behaviour before
the commit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[replaced link with mid.gmane.org that has message-id] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor
for a chip measured in clean air, it refers to the lowest expected reading.
Depending on the frequency, this measurement can vary by about 6db, thus
causing a higher reported channel noise and signal strength.
Factor in the 6db offset when converting internal noisefloor to channel noise.
This patch makes the reported values more accurate for all chips without
affecting NF calibration behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out reverting commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd
"ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to
bring the tx power back to normal levels on devices like the
Buffalo WZR-HP-G450H, this one needs to be reverted as well.
This revert improves tx power by ~10 db on that device
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: rmanohar@qca.qualcomm.com Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reduced the power consumption to half in full and network sleep.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Cc: Paul Stewart <pstew@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently free_all_bootmem_core ignores that node_min_pfn may be not
multiple of BITS_PER_LONG. Eg commit 6dccdcbe2c3e ("mm: bootmem: fix
checking the bitmap when finally freeing bootmem") shifts vec by lower
bits of start instead of lower bits of idx. Also
if (IS_ALIGNED(start, BITS_PER_LONG) && vec == ~0UL)
assumes that vec bit 0 corresponds to start pfn, which is only true when
node_min_pfn is a multiple of BITS_PER_LONG. Also loop in the else
clause can double-free pages (e.g. with node_min_pfn == start == 1,
map[0] == ~0 on 32-bit machine page 32 will be double-freed).
This bug causes the following message during xtensa kernel boot:
bootmem::free_all_bootmem_core nid=0 start=1 end=8000
BUG: Bad page state in process swapper pfn:00001
page:d04bd020 count:0 mapcount:-127 mapping: (null) index:0x2
page flags: 0x0()
Call Trace:
bad_page+0x8c/0x9c
free_pages_prepare+0x5e/0x88
free_hot_cold_page+0xc/0xa0
__free_pages+0x24/0x38
__free_pages_bootmem+0x54/0x56
free_all_bootmem_core$part$11+0xeb/0x138
free_all_bootmem+0x46/0x58
mem_init+0x25/0xa4
start_kernel+0x11e/0x25c
should_never_return+0x0/0x3be7
The fix is the following:
- always align vec so that its bit 0 corresponds to start
- provide BITS_PER_LONG bits in vec, if those bits are available in the
map
- don't free pages past next start position in the else clause.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Cc: Gavin Shan <shangw@linux.vnet.ibm.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Joonsoo Kim <js1304@gmail.com> Cc: Prasad Koya <prasad.koya@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current calculation in pfn_to_bitidx assumes that (pfn -
zone->zone_start_pfn) >> pageblock_order will return the same bit for
all pfn in a pageblock. If zone_start_pfn is not aligned to
pageblock_nr_pages, this may not always be correct.
Consider the following with pageblock order = 10, zone start 2MB:
This means that calling {get,set}_pageblock_migratetype on a single page
will not set the migratetype for the full block. Fix this by rounding
down zone_start_pfn when doing the bitidx calculation.
For our use case, the effects of this bug were mostly tied to the fact
that CMA allocations would either take a long time or fail to happen.
Depending on the driver using CMA, this could result in anything from
visual glitches to application failures.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When poweroff machine, kernel_power_off() call disable_nonboot_cpus().
And if we have HOTPLUG_CPU configured, disable_nonboot_cpus() is not an
empty function but attempt to actually disable the nonboot cpus. Since
system state is SYSTEM_POWER_OFF, play_dead() won't be called and thus
disable_nonboot_cpus() hangs. Therefore, we make this patch to avoid
poweroff failure.
The check to whom a device is reserved is done by checking the path
state of the affected channel paths. If it turns out that one path is
flagged as reserved by someone else the whole device is marked as such.
However the meaning of the RESVD_ELSE bit is that the addressed device
is reserved to a different pathgroup (and not reserved to a different
LPAR). If we do this test on a path which is currently not a member of
the pathgroup we could erroneously mark the device as reserved to
someone else.
To fix this collect the reserved state for all potential members of the
pathgroup and only mark the device as reserved if all of those potential
members have the RESVD_ELSE bit set.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to memory slot sorting this loop compared all of the user memory
slots for overlap with new entries. With memory slot sorting, we're
just checking some number of entries in the array that may or may not
be user slots. Instead, walk all the slots with kvm_for_each_memslot,
which has the added benefit of terminating early when we hit the first
empty slot, and skip comparison to private slots.
The locking in update_vsyscall_tz() is not only unnecessary because the vdso
code copies the data unproteced in __kernel_gettimeofday() but also
introduces a hard to reproduce race condition between update_vsyscall()
and update_vsyscall_tz(), which causes user space process to loop
forever in vdso code.
The following patch removes the locking from update_vsyscall_tz().
Locking is not only unnecessary because the vdso code copies the data
unprotected in __kernel_gettimeofday() but also erroneous because updating
the tb_update_count is not atomic and introduces a hard to reproduce race
condition between update_vsyscall() and update_vsyscall_tz(), which further
causes user space process to loop forever in vdso code.
The below scenario describes the race condition,
x==0 Boot CPU other CPU
proc_P: x==0
timer interrupt
update_vsyscall
x==1 x++;sync settimeofday
update_vsyscall_tz
x==2 x++;sync
x==3 sync;x++
sync;x++
proc_P: x==3 (loops until x becomes even)
Because the ++ operator would be implemented as three instructions and not
atomic on powerpc.
A similar change was made for x86 in commit 6c260d58634
("x86: vdso: Remove bogus locking in update_vsyscall_tz")
Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we build a kernel with CONFIG_RELOCATABLE=y CONFIG_CRASH_DUMP=n,
the kernel fails when we run at a non zero offset. It turns out
we were incorrectly wrapping some of the relocatable kernel code
with CONFIG_CRASH_DUMP.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was chasing down a bug of random validity intercepts on s390.
(guest prefix page not mapped in the host virtual aspace). Turns out
that the problem was a wrong address space control element. The
cause was quite complex:
During paging activity a DAT protection during SIE caused a program
interrupt. Normally, the sie retry loop tries to catch all
interrupts during and shortly before sie to rerun the setup. The
problem is now that protection causes a suppressing program interrupt,
causing the PSW to point to the instruction AFTER SIE in case of DAT
protection. This confused the logic of the retry loop to not trigger,
instead we jumped directly back to SIE after return from
the program interrupt. (the protection fault handler itself did
a rewind of the psw). This usually works quite well, but:
If now the protection fault handler has to wait, another program
might be scheduled in. Later on the sie process will be schedules
in again. In that case the content of CR1 (primary address space)
will be wrong because switch_to will put the user space ASCE into CR1
and not the guest ASCE.
In addition the program parameter is also wrong for every protection
fault of a guest, since we dont issue the SPP instruction.
So lets also check for PSW == instruction after SIE in the program
check handler. Instead of expensively checking all program
interruption codes that might be suppressing we assume that a program
interrupt pointing after SIE was always a program interrupt in SIE.
(Otherwise we have a kernel bug anyway).
We also have to compensate the rewinding, since the C-level handlers
will do that. Therefore we need to add a nop with the same length
as SIE before the sie_loop.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> CC: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer kernels (linux-next with the transparent huge page patches)
use rrbm if the feature is announced via feature bit 66.
RRBM will cause intercepts, so KVM does not handle it right now,
causing an illegal instruction in the guest.
The easy solution is to disable the feature bit for the guest.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were using wrong IRQ number so clearing wasn't working at all.
Depending on a platform this could result in a one device having two
interrupts assigned. On BCM4706 this resulted in all IRQs being broken.
We know that we have issues with the fw in the reclaim path.
This is why iwl_reclaim doesn't complain too loud when it
happens since it is recoverable. Somehow, the caller of
iwl_reclaim however WARNed when it happens. This doesn't
make any sense.
When I digged into the history of that code, I discovered
that this bug occurs only when we receive a BA notification.
So move the W/A in the BA notification handling code where
it was before.
This patch addresses:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2387
This can lead to a panic if the driver isn't ready to
handle them. Since our interrupt line is shared, we can get
an interrupt at any time (and CONFIG_DEBUG_SHIRQ checks
that even when the interrupt is being freed).
If the op_mode has gone away, we musn't call it. To avoid
this the transport disables the interrupts when the hw is
stopped and the op_mode is leaving.
If there is an event that would cause an interrupt the INTA
register is updated regardless of the enablement of the
interrupts: even if the interrupts are disabled, the INTA
will be changed, but the device won't issue an interrupt.
But the ISR can be called at any time, so we ought ignore
the value in the INTA otherwise we can call the op_mode
after it was freed.
I found this bug when the op_mode_start failed, and called
iwl_trans_stop_hw(trans, true). Then I played with the
RFKILL button, and removed the module.
While removing the module, the IRQ is freed, and the ISR is
called (CONFIG_DEBUG_SHIRQ enabled). Panic.
ieee80211_free_txskb() needs to be used instead of dev_kfree_skb_any for
tx packets passed to the driver from mac80211
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver reported that commit cd60042c caused his cifs mounts to
continually thrash through new inodes on readdir. His servers are not
sending inode numbers (or he's not using them), and the new test in
that function doesn't account for that sort of setup correctly.
If we're not using server inode numbers, then assume that the inode
attached to the dentry hasn't changed. Go ahead and update the
attributes in place, but keep the same inode number.
Reported-and-Tested-by: Oliver Mössinger <Oliver.Moessinger@ichaus.de> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The caller doesn't do anything with the dentry, so there's no point in
holding a reference to it on return. Also cifs_prime_dcache better
describes the actual purpose of the function.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the restart timer is running due to BUS-OFF and the device is
disconnected an dev_put will decrease the usage counter to -1 thus
blocking the interface removal, resulting in the following dmesg
lines repeating every 10s:
can: notifier: receive list not found for dev can0
can: notifier: receive list not found for dev can0
can: notifier: receive list not found for dev can0
unregister_netdevice: waiting for can0 to become free. Usage count = -1
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0a97e1e9f9a6 ('HID: apple: Add Apple wireless keyboard 2011 ANSI PID')
did not update the special driver list in hid-core.c, so hid-generic may
still bind to this device.
Reported-by: Ari Pollak <ari@scvngr.com>
References: http://bugs.debian.org/694546 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 263a523d18bc ("linux/kernel.h: Fix warning seen with W=1 due to
change in DIV_ROUND_CLOSEST") fixes a warning seen with W=1 due to
change in DIV_ROUND_CLOSEST.
Unfortunately, the C compiler converts divide operations with unsigned
divisors to unsigned, even if the dividend is signed and negative (for
example, -10 / 5U = 858993457). The C standard says "If one operand has
unsigned int type, the other operand is converted to unsigned int", so
the compiler is not to blame. As a result, DIV_ROUND_CLOSEST(0, 2U) and
similar operations now return bad values, since the automatic conversion
of expressions such as "0 - 2U/2" to unsigned was not taken into
account.
Fix by checking for the divisor variable type when deciding which
operation to perform. This fixes DIV_ROUND_CLOSEST(0, 2U), but still
returns bad values for negative dividends divided by unsigned divisors.
Mark the latter case as unsupported.
One observed effect of this problem is that the s2c_hwmon driver reports
a value of 4198403 instead of 0 if the ADC reads 0.
Other impact is unpredictable. Problem is seen if the divisor is an
unsigned variable or constant and the dividend is less than (divisor/2).
Since commit e303297e6c3a ("mm: extended batches for generic
mmu_gather") we are batching pages to be freed until either
tlb_next_batch cannot allocate a new batch or we are done.
This works just fine most of the time but we can get in troubles with
non-preemptible kernel (CONFIG_PREEMPT_NONE or CONFIG_PREEMPT_VOLUNTARY)
on large machines where too aggressive batching might lead to soft
lockups during process exit path (exit_mmap) because there are no
scheduling points down the free_pages_and_swap_cache path and so the
freeing can take long enough to trigger the soft lockup.
The lockup is harmless except when the system is setup to panic on
softlockup which is not that unusual.
The simplest way to work around this issue is to limit the maximum
number of batches in a single mmu_gather. 10k of collected pages should
be safe to prevent from soft lockups (we would have 2ms for one) even if
they are all freed without an explicit scheduling point.
This patch doesn't add any new explicit scheduling points because it
relies on zap_pmd_range during page tables zapping which calls
cond_resched per PMD.
The following lockup has been reported for 3.0 kernel with a huge
process (in order of hundreds gigs but I do know any more details).
tm_mon is 0..11, whereas vt8500 expects 1..12 for the month field,
causing invalid date errors for January, and causing the day field to
roll over incorrectly.
The century flag is only handled in vt8500_rtc_read_time, but not set in
vt8500_rtc_set_time. This patch corrects the behaviour of the century
flag.
Signed-off-by: Edgar Toernig <froese@gmx.de> Signed-off-by: Tony Prisk <linux@prisktech.co.nz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Control register bitfield for 12H/24H mode is handled incorrectly.
Setting CR_24H actually enables 12H mode. This patch renames the define
and changes the initialization code to correctly set 24H mode.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz> Cc: Edgar Toernig <froese@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already perform the ida_simple_remove() in rtc_device_release(),
which is an appropriate place. Commit 2830a6d20 ("rtc: recycle id when
unloading a rtc driver") caused the kernel to emit
ida_remove called for id=0 which is not allocated.
warnings when rtc_device_release() tries to release an alread-released
ID.
Let's restore things to their previous state and then work out why
Vincent's kernel wasn't calling rtc_device_release() - presumably a bug
in a specific sub-driver.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de> Acked-by: Alexander Holler <holler@ahsoftware.de> Cc: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inb/outb macros for CRIS are broken from a number of points of view,
missing () around parameters and they have an unprotected if statement
in them. This was breaking the compile of IPMI on CRIS and thus I was
being annoyed by build regressions, so I fixed them.
Plus I don't think they would have worked at all, since the data values
were missing "&" and the outsl had a "3" instead of a "4" for the size.
From what I can tell, this stuff is not used at all, so this can't be
any more broken than it was before, anyway.
We display a list of supplementary group for each process in
/proc/<pid>/status. However, we show only the first 32 groups, not all of
them.
Although this is rare, but sometimes processes do have more than 32
supplementary groups, and this kernel limitation breaks user-space apps
that rely on the group list in /proc/<pid>/status.
Number 32 comes from the internal NGROUPS_SMALL macro which defines the
length for the internal kernel "small" groups buffer. There is no
apparent reason to limit to this value.
This patch removes the 32 groups printing limit.
The Linux kernel limits the amount of supplementary groups by NGROUPS_MAX,
which is currently set to 65536. And this is the maximum count of groups
we may possibly print.
The atomic64 library uses a handful of static spin locks to implement
atomic 64-bit operations on architectures without support for atomic
64-bit instructions.
Unfortunately, the spinlocks are initialized in a pure initcall and that
is too late for the vfs namespace code which wants to use atomic64
operations before the initcall is run.
This became a problem as of commit 8823c079ba71: "vfs: Add setns support
for the mount namespace".
Commit 284f5f9 was intended to disable the "only_one_child()" optimization
on Stratus ftServer systems, but its DMI check is wrong. It looks for
DMI_SYS_VENDOR that contains "ftServer", when it should look for
DMI_SYS_VENDOR containing "Stratus" and DMI_PRODUCT_NAME containing
"ftServer".
Ulrich reported that his USB3 cardreader does not work reliably when
connected to the USB3 port. It turns out that USB3 controller failed to
awaken when plugging in the USB3 cardreader. Further experiments found
that the USB3 host controller can only be awakened via polling, not via PME
interrupt. But if the PCIe port to which the USB3 host controller is
connected is suspended, we cannot poll the controller because its config
space is not accessible when the PCIe port is in a low power state.
To solve the issue, the PCIe port will not be suspended if any subordinate
device needs PME polling.
[bhelgaas: use bool consistently rather than mixing int/bool]
Reference: http://lkml.kernel.org/r/50841CCC.9030809@uli-eckhardt.de Reported-by: Ulrich Eckhardt <usb@uli-eckhardt.de> Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Huang Ying <ying.huang@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Always in D0 state, because some devices do not work again after
being put into D3 by the PCI bus.
- In SUSPENDED state if allowed, so that the parent devices can still
be put into low power state.
To satisfy these requirements, the runtime PM for the unbound PCI
devices are disabled and set to SUSPENDED state. One issue of this
solution is that the PCI devices will be put into SUSPENDED state even
if the SUSPENDED state is forbidden via the sysfs interface
(.../power/control) of the device. This is not an issue for most
devices, because most PCI devices are not used at all if unbound.
But there are exceptions. For example, unbound VGA card can be used
for display, but suspending its parents makes it stop working.
To fix the issue, we keep the runtime PM enabled when the PCI devices
are unbound. But the runtime PM callbacks will do nothing if the PCI
devices are unbound. This way, we can put the PCI devices into
SUSPENDED state without putting the PCI devices into D3 state.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=48201 Signed-off-by: Huang Ying <ying.huang@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We weren't clearing card->tx_skb[port] when processing the TX done interrupt.
If there wasn't another skb ready to transmit immediately, this led to a
double-free because we'd free it *again* next time we did have a packet to
send.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a call goes out, the signing code adjusts the sequence number
upward by two to account for the request and the response. An NT_CANCEL
however doesn't get a response of its own, it just hurries the server
along to get it to respond to the original request more quickly.
Therefore, we must adjust the sequence number back down by one after
signing a NT_CANCEL request.
Reported-by: Tim Perry <tdparmor-sambabugs@yahoo.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is likely due to a race vs. a reconnection event.
The current code checks for a NULL socket in smb_send_kvec, but that's
too late. By the time that check is done, the socket will already have
been passed to kernel_setsockopt. Move the check into smb_send_rqst, so
that it's checked earlier.
In truth, this is a bit of a half-assed fix. The -ENOTSOCK error
return here looks like it could bubble back up to userspace. The locking
rules around the ssocket pointer are really unclear as well. There are
cases where the ssocket pointer is changed without holding the srv_mutex,
but I'm not clear whether there's a potential race here yet or not.
This code seems like it could benefit from some fundamental re-think of
how the socket handling should behave. Until then though, this patch
should at least fix the above oops in most cases.
Reported-and-Tested-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
File descriptors (even those for writing) do not hold freeze protection.
Thus mark_files_ro() must call __mnt_drop_write() to only drop protection
against remount read-only. Calling mnt_drop_write_file() as we do now
results in:
[ BUG: bad unlock balance detected! ] 3.7.0-rc6-00028-g88e75b6 #101 Not tainted
-------------------------------------
kworker/1:2/79 is trying to release lock (sb_writers) at:
[<ffffffff811b33b4>] mnt_drop_write+0x24/0x30
but there are no more locks to release!
Reported-by: Zdenek Kabelac <zkabelac@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flush_cache_louis flushes the D-side caches to the point of unification
inner-shareable. On uniprocessor CPUs, this is defined as zero and
therefore no flushing will take place. Rather than invent a new interface
for UP systems, instead use our SMP_ON_UP patching code to read the
LoUU from the CLIDR instead.
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com> Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 34ae6c96a6a7 ("ARM: 7298/1: realview: fix mapping of MPCore
private memory region") accidentally broke the definition for the base
address of the private peripheral region on revision B Realview-EB
boards.
This patch uses the correct address for REALVIEW_EB11MP_PRIV_MEM_BASE.
Acked-by: Marc Zyngier <marc.zyngier@arm.com> Tested-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log