Bin Meng [Mon, 10 Aug 2015 06:58:39 +0000 (23:58 -0700)]
x86: Set APs' req_seq to the reg number from device tree
Multiple APs are brought up simultaneously and they may get the same
seq num in the uclass_resolve_seq() during device_probe(). To avoid
this, set req_seq to the reg number in the device tree in advance.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Aug 2015 04:02:54 +0000 (22:02 -0600)]
x86: Show the un-relocated IP address in exceptions
When trying to figure out where an exception has occured, the relocated
address is not a lot of help. Its value depends on various factors. Show
the un-relocated IP as well. This can be looked up in System.map directly.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Unfortunately this commit breaks chromebook_link because it adds lots of PCI devices
before relocation and there is not enough pre-reloc malloc() memory.
Rathar then increase this memory, revert for now until we figure this out.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Tue, 11 Aug 2015 02:44:32 +0000 (20:44 -0600)]
x86: Switch to using generic global_data setup
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.
Drop the unneeded code and adjust the hooks in board_f.c to cope.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Tue, 11 Aug 2015 02:44:31 +0000 (20:44 -0600)]
x86: Move the GDT into global_data
Rather than keeping track of the Global Descriptor Table in its own memory
we may as well put it in global_data with everything else. As a first step,
stop using the separately allocated GDT.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Tue, 11 Aug 2015 02:44:30 +0000 (20:44 -0600)]
Allow arch-specific setting of global_data in board_init_f_mem()
At present we have a simple assignment to gd. With some archs this is
implemented as a register or through some other means; a simple assignment
does not suit in all cases.
Change this to a function and add documentation to describe how this all
works.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <yorksun@freescale.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stephen Warren [Sun, 9 Aug 2015 17:25:00 +0000 (11:25 -0600)]
cm5200: fix FAT function prototypes
Remove FAT function prototypes from the cm5200 firmware update code, and
include the relevant headers instead.
This exposes the fact that the custom prototyoe for do_fat_read() in
this file was incorrect. Rather than simply fixing the call-site, replace
do_fat_read() with fat_exists(). This removes the only use of
do_fat_read() outside of the FAT code.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Peng Fan [Fri, 14 Aug 2015 09:36:16 +0000 (11:36 +0200)]
Add missing part of: "power: pmic: pfuze100 support driver model"
This part of mentioned commit, was missed by my mistake during the rebase. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Original commit message:
power: pmic: pfuze100 support driver model
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Change-Id: I4fc88414f3c0285f9648e47ec7aed60addeccc4d Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 10 Aug 2015 13:05:07 +0000 (07:05 -0600)]
x86: Split out fsp_init_phase_pci() code into a new function
This code may be useful for boards that use driver model for PCI.
Note: It would be better to have driver model automatically call this
function somehow. However for now it is probably safer to have it under
board control.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 10 Aug 2015 13:05:04 +0000 (07:05 -0600)]
dm: pci: Add a way to iterate through all PCI devices
These functions allow iteration through all PCI devices including bridges.
The children of each PCI bus are returned in turn. This can be useful for
configuring, checking or enumerating all the devices.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 10 Aug 2015 13:05:03 +0000 (07:05 -0600)]
dm: pci: Provide friendly config access functions
At present there are no PCI functions which allow access to PCI
configuration using a struct udevice. This is a sad situation for driver
model as it makes use of PCI harder. Add these functions.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Sat, 8 Aug 2015 14:01:23 +0000 (22:01 +0800)]
x86: fsp: Do not assert VPD_IMAGE_REV when DEBUG
When using different release version of Intel FSP, the VPD_IMAGE_REV
is different (ie: BayTrail Gold 3 is 0x0303 while Gold 4 is 0x0304).
Remove the asserting of this so that U-Boot does not hang in a debug
build.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Andrew Bradford [Fri, 7 Aug 2015 12:36:35 +0000 (08:36 -0400)]
x86: baytrail: Configure FSP UPD from device tree
Allow for configuration of FSP UPD from the device tree which will
override any settings which the FSP was built with itself.
Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
settings from the Intel FSPv4 Gold release to the respective dts files,
with the condition that the memory-down parameters for MinnowMax are
also used.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Removed fsp,mrc-debug-msg and fsp,enable-xhci for minnowmax, bayleybay
Fixed lines >80col Signed-off-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 6 Aug 2015 09:36:01 +0000 (02:36 -0700)]
x86: baytrail: Add all IDE/SATA PCI device IDs
The BayTrail SoC has 4 different PCI devices IDs regarding to IDE
and AHCI. Add these IDs in pci_ids.h and also add the other SATA
ID in the Bayley Bay and MinnowMax board configuration header.
Bin Meng [Thu, 6 Aug 2015 08:31:20 +0000 (01:31 -0700)]
common: Display >=4GiB memory bank size
bd->bi_dram[] has both start address and size defined as 32-bit,
which is not the case on some platforms where >=4GiB memory bank
is used. Change them to support such memory banks.
Hans de Goede [Sat, 8 Aug 2015 14:03:29 +0000 (16:03 +0200)]
video: Add support for the ANX9804 parallel lcd to dp bridge chip
Add support for the ANX9804 bridge chip, which can take pixel data coming
from a parallel LCD interface and translate it on the fly into a DP
interface for driving eDP TFT displays. It uses I2C for configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Thu, 6 Aug 2015 18:10:20 +0000 (20:10 +0200)]
sunxi: gpio: Add support for the gpio banks which are part of the R-io cluster
sun6i and later have a couple of io-blocks which are shared between the
main CPU core and the "R" cpu which is small embedded cpu which can be
active while the main system is suspended.
These gpio banks sit at a different mmio address then the normal banks,
and have a separate devicetree node and compatible, this adds support for
these banks to the sunxi-gpio code when built with device-model support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Thu, 6 Aug 2015 13:39:05 +0000 (15:39 +0200)]
sunxi: Fix gmac not working on the Colombus board
The phy is using a RGMII interface, which we need to specify in our
board-config, and the dts needs a gmac section (the dts changes have
also been submitted to the kernel).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Tue, 4 Aug 2015 22:06:47 +0000 (00:06 +0200)]
sunxi: display: Add overscan correction
Add support for making the visual area of the framebuffer smaller and
drawing a black border around it. This is intended for use with
overscanning monitors (esp. with composite video out), to avoid part
of the picture being invisible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
Hans de Goede [Tue, 4 Aug 2015 10:15:39 +0000 (12:15 +0200)]
cfbconsole: Add support for stride != width
cfbconsole currently assumes that the width and stride of the framebuffer
are the same, in most places where stride matters it uses a VIDEO_LINE_LEN
helper macro.
This commit changes the few places not using VIDEO_LINE_LEN to also use
VIDEO_LINE_LEN, and protects the default VIDEO_LINE_LEN with a #ifndef
guard, allowing the boards config.h to override and, and thus support
cases where stride != width.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
Stephen Warren [Fri, 7 Aug 2015 22:12:45 +0000 (16:12 -0600)]
ARM: tegra: represent RAM in 1 or 2 banks
Represent all available RAM in either one or two banks. The first bank
describes any RAM below 4GB. The second bank describes any RAM above 4GB.
This split is driven by the following requirements:
- The NVIDIA L4T kernel requires separate entries in the DT /memory/reg
property for memory below and above the 4GB boundary. The layout of that
DT property is directly driven by the entries in the U-Boot bank array.
- On systems with RAM beyond a physical address of 4GB, the potential
existence of a carve-out at the end of RAM below 4GB can only be
represented using multiple banks, since usable RAM is not contiguous.
While making this change, add a lot more comments re: how and why RAM is
represented in banks, and implement a few more "semantic" functions that
define (and perhaps later detect at run-time) the size of any carve-out.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 7 Aug 2015 22:12:44 +0000 (16:12 -0600)]
ARM: tegra: query_sdram_size() cleanup
The return value of query_sdram_size() is assigned directly to
gd->ram_size in dram_init(). Adjust the return type to match the field
it's assigned to. This has the beneficial effect that on 64-bit systems,
the return value can correctly represent large RAM sizes over 4GB.
For similar reasons, change the type of variable size_bytes in the same
way.
query_sdram_size() would previously clip the detected RAM size to at most
just under 4GB in all cases, since on 32-bit systems, larger values could
not be represented. Disable this feature on 64-bit systems since the
representation restriction does not exist.
On 64-bit systems, never call get_ram_size() to validate the detected/
calculated RAM size. On any system with a secure OS/... carve-out, RAM
may not have a single contiguous usable area, and this can confuse
get_ram_size(). Ideally, we'd make this call conditional upon some other
flag that indicates specifically that a carve-out is actually in use. At
present, building for a 64-bit system is the best indication we have of
this fact. In fact, the call to get_ram_size() is not useful by the time
U-Boot runs on any system, since U-Boot (and potentially much other early
boot software) always runs from RAM on Tegra, so any mistakes in memory
controller register programming will already have manifested themselves
and prevented U-Boot from running to this point. In the future, we may
simply delete the call to get_ram_size() in all cases.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 7 Aug 2015 22:12:43 +0000 (16:12 -0600)]
ARM: tegra: move kernel_addr_r on T210
The new value is the most likely value where the kernel wants to end up
at run-time. Selecting this value as the load address likely avoids the
need to copy the kernel image from the actual load address to the desired
load address. Note that this isn't guaranteed since the kernel may wish
to run at an arbitrary location. In that case, U-Boot will still relocate
the image according to its wishes; this change is a performance
optimization, not a hard-coding of the final image location.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Fri, 20 Mar 2015 12:24:22 +0000 (13:24 +0100)]
ARM: tegra: Make pinmux.h standalone includible
This header file uses type definitions (u8, u32) from linux/types.h but
doesn't include it. If includes aren't carefully ordered this can cause
build failures.
Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:12 +0000 (00:47 +0200)]
apalis/colibri_t30: fix usb dm regression
Unfortunately currently both Apalis T30 as well as Colibri T30 crash
upon starting USB host support. This is due to the following patch not
having taken into account that our T30 device trees were defaulting to
peripheral only mode instead of otg:
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:11 +0000 (00:47 +0200)]
colibri_t20: fix reset out pin
Make sure SODIMM pin 87 nRESET_OUT is released properly by explicitly
setting its pin mux function to GMI. This solves some issues with e.g.
USB not being fully operational on carrier boards with USB hubs
connected to reset if U-Boot got loaded via recovery mode aka rcm.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:10 +0000 (00:47 +0200)]
apalis/colibri_t20/30: clean-up
Various clean-ups either in comments, order or spacing without any
functional impact:
- Add some comments in the device trees resp. reorder some parameters
for consistency across all our modules.
- Sort some include files alphabetically (while leaving common.h on
top of course).
- Streamline some comments in the configuration files and fix the
spacing from using spaces to tabs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:05 +0000 (00:47 +0200)]
tegra: nand: fix read_byte required for proper onfi detection
Fix PIO read_byte() implementation not only used for the legacy READ ID
but also the PARAM command required for proper ONFI detection.
This fix is inspired by Lucas Stach's Linux Tegra NAND driver of late
(not mainline yet but getting there soon I hope).
I vaguely remember that those commands are special on 16-bit bus NAND
(e.g. always return 8-bit data regardless) and later Linux MTD fixed/
changed the way this is handled which in turn broke once U-Boot pulled
that in. Basically instead of doing PIO read regular DMA block read is
now used which this patch actually fixes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:04 +0000 (00:47 +0200)]
colibri_t20: disable PMIC sleep mode on low supply voltage
The Colibri T20's PMIC enters a sleep mode on low supply voltage < 3.0V
±2.5% (2.92...3.08V). Rising the main supply voltage again does not
bring it back to regular operation. Not even a full reset does bring
the module back. A full power cycle was required to reboot the system.
A long positive pulse on the PMICs resume pin also reboots the system
but this pin is only accessible as a test point on the module.
This patch configures the PMIC through I2C to not enter this sleep mode
plus force it to normal state upon sleep request exit should this ever
happen.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stefan Agner [Wed, 5 Aug 2015 15:17:01 +0000 (17:17 +0200)]
logos: add Toradex logo
Use the boot loader splash screen from WinCE which matches our
wallpapers position wise. Although the logo is an 8-bit indexed BMP as
well colours looked odd at first in U-Boot. After converting to full
RGB palette and converting back to an indexed BMP using imagemagick
the Logo showed up properly.
This fixes the following warning (and the runtime error reporting):
../common/image-fdt.c:491:4: warning: 'fdt_ret' may be used
uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Simon Glass <sjg@chromium.org>
Marcel Ziswiler [Wed, 5 Aug 2015 15:17:00 +0000 (17:17 +0200)]
generic-board: allow showing custom board info
Allow showing custom board info from a checkboard() function being
implemented if CONFIG_CUSTOM_BOARDINFO is specified. Previously the
device tree model was always displayed not taking any
CONFIG_CUSTOM_BOARDINFO into account.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org>
fs/fs.c: read up to EOF when len would read past EOF
http://lists.denx.de/pipermail/u-boot/2012-September/134347.html
allows for reading files in chunks from the shell.
When this feature is used to read past the end of a file an error
was returned instead of returning the bytes read up to the end of
file. Thus the following fails in the shell:
offset = 0
len = chunksize
do
read file, offset, len
write data
until bytes_read < len
The patch changes the behaviour to printing an informational
message and returning the actual read number of bytes aka read(2)
behaviour for convenient use in U-Boot scripts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Marcel Ziswiler [Tue, 4 Aug 2015 13:49:50 +0000 (15:49 +0200)]
common/lcd_console: fix console/logo regression
The following commit changed the order of the column vs. row parameter
to the lcd_init_console() function but missed actually changing it as
well the second time it is called from lcd_clear() which resulted in a
garbled text console which this patch fixes.
Nikita Kiryanov [Mon, 3 Aug 2015 09:36:58 +0000 (12:36 +0300)]
kconfig: add config option for shell prompt
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <trini@konsulko.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion] Signed-off-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Sat, 1 Aug 2015 07:39:13 +0000 (16:39 +0900)]
ARM: drop "optional" from target select in favor of ARCH_VERSATILE
Since commit a26cd04920dc ("arch: Make board selection choices
optional"), Kconfig could create such an insane .config file that
no SoC/board is selected.
This is now a real problem for Buildroot, for example.
(http://lists.busybox.net/pipermail/buildroot/2015-July/135125.html)
This commit drops the "optional" from the ARM target select menu
in favor of "Versatile family".
Rationale:
- Historically, Linux chose versatile_defconfig as the default
of ARM defconfig. (arch/arm/Makefile of Linux describes:
KBUILD_DEFCONFIG := versatile_defconfig)
Tom Rini [Fri, 31 Jul 2015 23:55:10 +0000 (19:55 -0400)]
ARM: SPL: Use CONFIG_SPL_DM not CONFIG_DM
We now have the CONFIG_SPL_DM for code within SPL to toggle caring about
DM or not. Without this change platforms that do enable CONFIG_DM but
not CONFIG_SPL_DM may be broken (such as OMAP5).
Cc: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 31 Jul 2015 23:55:09 +0000 (19:55 -0400)]
gpio: omap: Drop 'method' parameter
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
- Re-sync DT files for am33xx with Linux Kernel v4.1
- Include DT file now for the "AM335x GP EVM" and build target for it,
via device tree and DM.
- We only need to provide platform data for UART when OF_CONTROL isn't
also enabled really. We can just push GPIO to coming from DT
Peter Griffin [Thu, 30 Jul 2015 17:55:23 +0000 (18:55 +0100)]
ARM64: hikey: hi6220: Add u-boot support for the 96boards CE HiKey board.
HiKey is the first 96boards consumer edition compliant board. It features a hi6220
SoC which has eight ARM A53 cpu's.
This initial port adds support for: -
1) Serial
2) eMMC / SD card
3) USB
4) GPIO
It has been tested with Arm Trusted Firmware running u-boot as the BL33 executable.
Notes:
eMMC has been tested with basic reading of eMMC partition into DDR. I have not
tested writing / erasing. Due to lack of clock control it won't be
running in the most performant high speed mode.
SD card slot has been tested for reading and booting kernels into DDR.
It is also currently configured to save the u-boot environment to the
SD card.
USB has been tested with ASIX networking adapter to tftpboot kernels
into DDR. On v2015.07-rc2 dhcp now works, and also USB mass storage
are correctly enumerated.
GPIO has been tested using gpio toggle GPIO4_1-3 to flash the LEDs.
Basic SoC datasheet can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf
Board schematic can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
96Boards-Hikey-Rev-A1.pdf
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Peter Griffin [Thu, 30 Jul 2015 17:55:22 +0000 (18:55 +0100)]
mmc: hi6220_dw_mmc: Add hi6220 glue code for dw_mmc controller.
This patch adds the glue code for hi6220 SoC which has 2x synopsis
dw_mmc controllers. This will be used by the hikey board support
in subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Griffin [Thu, 30 Jul 2015 17:55:21 +0000 (18:55 +0100)]
pmic: pmic_hi6553: Add a driver for the hi6553 pmic found on hikey board.
This adds a simple pmic driver for the hi6553 pmic which is used in
conjunction with the hi6220 SoC on the hikey board. Eventually this
driver will be updated to be a proper UCLASS PMIC driver which
can parse the voltages direct from device tree.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Gong Qianyu [Thu, 30 Jul 2015 06:00:01 +0000 (14:00 +0800)]
common/cmd_source.c: Fix the source command failure under 64-bit platform
Modify the data pointer type from ulong* to u32*.
For arm64 type "ulong" could be 64-bit. Then in line 89 of common/cmd_source.c:
"while (*data++);" data will point to the next 64 bits each time. As the uImage
file generated by mkimage tool keeps the same data format in either 32-bit or 64-bit
platform, the difference would cause failure in 64-bit platform.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Register Base addresses are same for PLLs in all
keystone platforms. If a PLL is not available, the corresponding
register addresses are marked as reserved.
Hence use a common definition.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
projects / karo-tx-uboot.git / log