According to the experiment I did, PCI config access is blocked
on P7IOC frozen PE by hardware, but PHB3 doesn't do that. That
means we always get 0xFF's while dumping PCI config space of the
frozen PE on P7IOC. We don't have the problem on PHB3. So we have
to enable I/O prioir to collecting error log. Otherwise, meaningless
0xFF's are always returned.
The patch fixes it by EEH flag (EEH_ENABLE_IO_FOR_LOG), which is
selectively set to indicate the case for: P7IOC on PowerNV platform,
pSeries platform.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are multiple global EEH flags. Almost each flag has its own
accessor, which doesn't make sense. The patch refactors EEH flag
accessors so that they look unified:
eeh_add_flag(): Add EEH flag
eeh_clear_flag(): Clear EEH flag
eeh_has_flag(): Check if one specific flag has been set
eeh_enabled(): Check if EEH functionality has been enabled
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Function eeh_iommu_group_to_pe() iterates each PCI device to check
the binding IOMMU group with get_iommu_table_base(), which possibly
fetches pdev->dev.archdata.dma_data.dma_offset. It's (0x1 << 59)
for "bypass" cases.
The patch fixes the issue by iterating devices hooked to the IOMMU
group and fetch IOMMU table there.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PHB3, PCI devices can bypass IOMMU for DMA access. If we pass
through one PCI device, whose hose driver ever enable the bypass
mode, pdev->dev.archdata.dma_data.iommu_table_base isn't IOMMU
table. However, EEH needs access the IOMMU table when the device
is owned by guest.
The patch fixes pdev->dev.archdata.dma_data.iommu_table when
passing through the device to guest in pnv_pci_ioda2_set_bypass().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mike Qiu [Tue, 15 Jul 2014 05:42:22 +0000 (01:42 -0400)]
powerpc/eeh: Wrong place to call pci_get_slot()
pci_get_slot() is called with hold of PCI bus semaphore and it's not
safe to be called in interrupt context. However, we possibly checks
EEH error and calls the function in interrupt context. To avoid using
pci_get_slot(), we turn into device tree for fetching location code.
Otherwise, we might run into WARN_ON() as following messages indicate:
Lucas Tanure [Thu, 24 Jul 2014 13:24:06 +0000 (10:24 -0300)]
powerpc: Fix wrong defintion in boot/io.h
Fix wrong __IO_H definition in boot/io.h
Reported-by: Fernando Silveira <fsilveira@gmail.com> Signed-off-by: Lucas Tanure <tanure@linux.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pci: Reorder pci bus/bridge unregistration during PHB removal
Commit bcdde7e made __sysfs_remove_dir() recursive and introduced a BUG_ON
during PHB removal while attempting to delete the power managment attribute
group of the bus. This is a result of tearing the bridge and bus devices down
out of order in remove_phb_dynamic. Since, the the bus resides below the bridge
in the sysfs device tree it should be torn down first.
This patch simply moves the device_unregister call for the PHB bridge device
after the device_unregister call for the PHB bus.
Fixes: bcdde7e221a8 ("sysfs: make __sysfs_remove_dir() recursive") Cc: stable@vger.kernel.org Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Thu, 31 Jul 2014 19:24:37 +0000 (14:24 -0500)]
powerpc/powernv: Update dev->dma_mask in pci_set_dma_mask() path
powerpc defines various machine-specific routines for handling
pci_set_dma_mask(). The routines for machine "PowerNV" may neglect
to set dev->dma_mask. This could confuse anyone (e.g. drivers) that
consult dev->dma_mask to find the current mask. Set the dma_mask in
the PowerNV leaf routine.
Signed-off-by: Brian W. Hart <hartb@linux.vnet.ibm.com> CC: <stable@vger.kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott Wood [Sat, 2 Aug 2014 03:07:40 +0000 (22:07 -0500)]
powerpc/64e: Add __ref to early_alloc_pgtable()
This silences a section mismatch warning. early_alloc_pgtable() is
called from map_kernel_page() which cannot be __init, but only when
slab_is_available() returns false which can only happen during early
boot.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/cpufreq: Add pr_warn() on OPAL firmware failures
Cpufreq depends on platform firmware to implement PStates. In case of
platform firmware failure, cpufreq should not panic host kernel with
BUG_ON(). Less severe pr_warn() will suffice.
Add firmware_has_feature(FW_FEATURE_OPALv3) check to
skip probing for device-tree on non-powernv platforms.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> CC: <stable@vger.kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mike Qiu [Thu, 26 Jun 2014 06:58:47 +0000 (02:58 -0400)]
powerpc/eeh: sysfs entries lost
The sysfs entries are lost because of commit 2213fb1 ("powerpc/eeh:
Skip eeh sysfs when eeh is disabled"). That commit added condition
to create sysfs entries with EEH_ENABLED, which isn't populated
when trying to create sysfs entries on PowerNV platform during system
boot time. The patch fixes the issue by:
* Reoder EEH initialization functions so that they're same on
PowerNV/pSeries.
* Cache PE's primary bus by PowerNV platform instead of EEH core
to avoid kernel crash caused by the function reorder. Another
benefit with this is to avoid one eeh_probe_mode_dev() in EEH
core.
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com> Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Tue, 10 Jun 2014 01:41:57 +0000 (11:41 +1000)]
drivers/vfio: EEH support for VFIO PCI device
The patch adds new IOCTL commands for sPAPR VFIO container device
to support EEH functionality for PCI devices, which have been passed
through from host to somebody else via VFIO.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Acked-by: Alexander Graf <agraf@suse.de> Acked-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Tue, 10 Jun 2014 01:41:56 +0000 (11:41 +1000)]
powerpc/eeh: EEH support for VFIO PCI device
The patch exports functions to be used by new VFIO ioctl command,
which will be introduced in subsequent patch, to support EEH
functinality for VFIO PCI devices.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Acked-by: Alexander Graf <agraf@suse.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Tue, 10 Jun 2014 01:41:55 +0000 (11:41 +1000)]
powerpc/eeh: Avoid event on passed PE
We must not handle EEH error on devices which are passed to somebody
else. Instead, we expect that the frozen device owner detects an EEH
error and recovers from it.
This avoids EEH error handling on passed through devices so the device
owner gets a chance to handle them.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Acked-by: Alexander Graf <agraf@suse.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge remote-tracking branch 'scott/next' into next
Scott writes:
Highlights include e6500 hardware threading support, an e6500 TLB erratum
workaround, corenet error reporting, support for a new board, and some
minor fixes.
In commit ae91d60ba88ef0bdb1b5e9b2363bd52fc45d2af7, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The Coccinelle semantic patch that makes this change is as follows:
powerpc/mpic_msgr: Use kcalloc and correct the argument to sizeof
mpic_msgrs has type struct mpic_msgr **, not struct mpic_msgr *, so the
elements of the array should have pointer type, not structure type.
The advantage of kcalloc is, that will prevent integer overflows which
could result from the multiplication of number of elements and size and
it is also a bit nicer to read.
The Coccinelle semantic patch that makes the first change is as follows:
// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@
x =
<+...sizeof(
- T
+ *x
)...+>
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Scott Wood <scottwood@freescale.com>
The CoreNet Coherency Fabric is part of the memory subsystem on
some Freescale QorIQ chips. It can report coherency violations (e.g.
due to misusing memory that is mapped noncoherent) as well as
transactions that do not hit any local access window, or which hit a
local access window with an invalid target ID.
Signed-off-by: Scott Wood <scottwood@freescale.com> Reviewed-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Scott Wood [Wed, 11 Jun 2014 21:09:32 +0000 (16:09 -0500)]
powerpc/e6500: Work around erratum A-008139
Erratum A-008139 can cause duplicate TLB entries if an indirect
entry is overwritten using tlbwe while the other thread is using it to
do a lookup. Work around this by using tlbilx to invalidate prior
to overwriting.
To avoid the need to save another register to hold MAS1 during the
workaround code, TID clearing has been moved from tlb_miss_kernel_e6500
until after the SMT section.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Andy Fleming [Thu, 8 Dec 2011 07:20:27 +0000 (01:20 -0600)]
powerpc/e6500: Add support for hardware threads
The general idea is that each core will release all of its
threads into the secondary thread startup code, which will
eventually wait in the secondary core holding area, for the
appropriate bit in the PACA to be set. The kick_cpu function
pointer will set that bit in the PACA, and thus "release"
the core/thread to boot. We also need to do a few things that
U-Boot normally does for CPUs (like enable branch prediction).
Signed-off-by: Andy Fleming <afleming@freescale.com>
[scottwood@freescale.com: various changes, including only enabling
threads if Linux wants to kick them] Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Wed, 23 Jul 2014 19:38:02 +0000 (14:38 -0500)]
powerpc/booke: Define MSR bits the same way as reg.h
This ensures that all MSR definitions are consistently unsigned long,
and that MSR_CM does not become 0xffffffff80000000 (this is usually
harmless because MSR is 32-bit on booke and is mainly noticeable when
debugging, but still I'd rather avoid it).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Michael Ellerman [Wed, 23 Jul 2014 11:12:38 +0000 (21:12 +1000)]
powerpc/perf: Add per-event excludes on Power8
Power8 has a new register (MMCR2), which contains individual freeze bits
for each counter. This is an improvement on previous chips as it means
we can have multiple events on the PMU at the same time with different
exclude_{user,kernel,hv} settings. Previously we had to ensure all
events on the PMU had the same exclude settings.
The core of the patch is fairly simple. We use the 207S feature flag to
indicate that the PMU backend supports per-event excludes, if it's set
we skip the generic logic that enforces the equality of excludes between
events. We also use that flag to skip setting the freeze bits in MMCR0,
the PMU backend is expected to have handled setting them in MMCR2.
The complication arises with EBB. The FCxP bits in MMCR2 are accessible
R/W to a task using EBB. Which means a task using EBB will be able to
see that we are using MMCR2 for freezing, whereas the old logic which
used MMCR0 is not user visible.
The task can not see or affect exclude_kernel & exclude_hv, so we only
need to consider exclude_user.
The table below summarises the behaviour both before and after this
commit is applied:
exclude_user true false
------------------------------------
| User visible | N N
Before | Can freeze | Y Y
| Can unfreeze | N Y
------------------------------------
| User visible | Y Y
After | Can freeze | Y Y
| Can unfreeze | Y/N Y
------------------------------------
So firstly I assert that the simple visibility of the exclude_user
setting in MMCR2 is a non-issue. The event belongs to the task, and
was most likely created by the task. So the exclude_user setting is not
privileged information in any way.
Secondly, the behaviour in the exclude_user = false case is unchanged.
This is important as it is the case that is actually useful, ie. the
event is created with no exclude setting and the task uses MMCR2 to
implement exclusion manually.
For exclude_user = true there is no meaningful change to freezing the
event. Previously the task could use MMCR2 to freeze the event, though
it was already frozen with MMCR0. With the new code the task can use
MMCR2 to freeze the event, though it was already frozen with MMCR2.
The only real change is when exclude_user = true and the task tries to
use MMCR2 to unfreeze the event. Previously this had no effect, because
the event was already frozen in MMCR0. With the new code the task can
unfreeze the event in MMCR2, but at some indeterminate time in the
future the kernel will overwrite its setting and refreeze the event.
Therefore my final assertion is that any task using exclude_user = true
and also fiddling with MMCR2 was deeply confused before this change, and
remains so after it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Wed, 23 Jul 2014 11:12:36 +0000 (21:12 +1000)]
powerpc/perf: Clear all MMCR settings before calling compute_mmcr()
Because we reuse cpuhw->mmcr on each call to compute_mmcr() there's a
risk that we could forget to set one of the values and use whatever
value was in there previously.
Currently all the implementations are careful to set all the values, but
it's safer to clear them all before we call compute_mmcr().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Wed, 23 Jul 2014 07:31:36 +0000 (17:31 +1000)]
selftests/powerpc: Count more instructions & use decimal
Although we expect some small discrepancies for very large counts, we
seem to be able to count up to 64 billion instructions without too much
skew, so do so.
Also switch to using decimals for the instruction counts. This just
makes it easier to visually compare the expected vs actual values, as
well as the raw result from instructions.
Michael Ellerman [Wed, 23 Jul 2014 07:31:35 +0000 (17:31 +1000)]
selftests/powerpc: Count instructions under scheduler pressure
Have a task eat some cpu while we are counting instructions to create
some scheduler pressure. The idea being to try and unearth any bugs we
have in counting that only appear when context switching is happening.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Wed, 23 Jul 2014 07:31:33 +0000 (17:31 +1000)]
selftests/powerpc: Move core_busy_loop() into asm
There is at least one bug in core_busy_loop(), we use r0, but it's
not in the clobber list. We were getting away with this it seems but
that was luck.
It's also fishy to be touching the stack, even if we do it below the
stack pointer. It seems we get away with it, but looking at the
generated code that may just be luck.
So move it into assembler, do all the stack handling by hand. We create
a stack frame to save the non-volatiles in, so we can muck around with
them.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Wed, 23 Jul 2014 07:31:31 +0000 (17:31 +1000)]
selftests/powerpc: Don't ignore errors from sub Makefiles
Currently we ignore errors from our sub Makefiles. We inherited that
from the top-level selftests Makefile which aims to build and run as
many tests as possible and damn the torpedoes.
For the powerpc tests we'd instead like any errors to fail the build, so
we can automatically catch build failures.
We can achieve the best of both worlds by using -k, which tells make to
keep building when it hits an error, but still reports the error.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 17 Jul 2014 05:29:45 +0000 (15:29 +1000)]
powerpc: Document how we set AIL on guest kernels
I spent ten minutes scratching my head, trying to work out where we
enabled relocation on interrupts for guest kernels. Expand the doco to
make it clear.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Wed, 16 Jul 2014 02:02:43 +0000 (12:02 +1000)]
powerpc/pseries: Switch pseries drivers to use machine_xxx_initcall()
A lot of the code in platforms/pseries is using non-machine initcalls.
That means if a kernel built with pseries support runs on another
platform, for example powernv, the initcalls will still run.
Most of these cases are OK, though sometimes only due to luck. Some were
having more effect:
* hcall_inst_init
- Checking FW_FEATURE_LPAR which is set on ps3 & celleb.
* mobility_sysfs_init
- created sysfs files unconditionally
- but no effect due to ENOSYS from rtas_ibm_suspend_me()
* apo_pm_init
- created sysfs, allows write
- nothing checks the value written to though
* alloc_dispatch_log_kmem_cache
- creating kmem_cache on non-pseries machines
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 15 Jul 2014 12:22:24 +0000 (22:22 +1000)]
powerpc/powernv: Switch powernv drivers to use machine_xxx_initcall()
A lot of the code in platforms/powernv is using non-machine initcalls.
That means if a kernel built with powernv support runs on another
platform, for example pseries, the initcalls will still run.
That is usually OK, because the initcalls will check for something in
the device tree or elsewhere before doing anything, so on other
platforms they will usually just return.
But it's fishy for powernv code to be running on other platforms, so
switch them all to be machine initcalls. If we want any of them to run
on other platforms in future they should move to sysdev.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 15 Jul 2014 11:15:38 +0000 (21:15 +1000)]
powerpc: Remove misleading DISABLE_INTS
DISABLE_INTS has a long and storied history, but for some time now it
has not actually disabled interrupts.
For the open-coded exception handlers, just stop using it, instead call
RECONCILE_IRQ_STATE directly. This has the benefit of removing a level
of indirection, and making it clear that r10 & r11 are used at that
point.
For the addition case we still need a macro, so rename it to clarify
what it actually does.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 15 Jul 2014 11:15:36 +0000 (21:15 +1000)]
powerpc: Update comments in irqflags.h
The comment on TRACE_ENABLE_INTS is incorrect, and appears to have
always been incorrect since the code was merged. It probably came from
an original out-of-tree patch.
Replace it with something that's correct. Also propagate the message to
RECONCILE_IRQ_STATE(), because it's potentially subtle.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 15 Jul 2014 10:25:02 +0000 (20:25 +1000)]
powerpc: Move bad_stack() below the fwnmi_data_area
At the moment the allmodconfig build is failing because we run out of
space between altivec_assist() at 0x5700 and the fwnmi_data_area at
0x7000.
Fixing it permanently will take some more work, but a quick fix is to
move bad_stack() below the fwnmi_data_area. That gives us just enough
room with everything enabled.
bad_stack() is called from the common exception handlers, but it's a
non-conditional branch, so we have plenty of scope to move it further
way.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 10 Jul 2014 02:29:25 +0000 (12:29 +1000)]
powerpc: Remove CONFIG_POWER4
Although the name CONFIG_POWER4 suggests that it controls support for
power4 cpus, this symbol is actually misnamed.
It is a historical wart from the powermac code, which used to support
building a 32-bit kernel for power4. CONFIG_POWER4 was used in that
context to guard code that was 64-bit only.
In the powermac code we can just use CONFIG_PPC64 instead, and in other
places it is a synonym for CONFIG_PPC_BOOK3S_64.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 10 Jul 2014 02:29:22 +0000 (12:29 +1000)]
powerpc: Remove CONFIG_POWER3
Now that we have dropped power3 support we can remove CONFIG_POWER3. The
usage in pgtable_32.c was already dead code as CONFIG_POWER3 was not
selectable on PPC32.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 10 Jul 2014 02:29:19 +0000 (12:29 +1000)]
powerpc: Remove STAB code
Old cpus didn't have a Segment Lookaside Buffer (SLB), instead they had
a Segment Table (STAB). Now that we've dropped support for those cpus,
we can remove the STAB support entirely.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 10 Jul 2014 02:29:18 +0000 (12:29 +1000)]
powerpc: Drop support for pre-POWER4 cpus
We inadvertently broke power3 support back in 3.4 with commit f5339277eb8d "powerpc: Remove FW_FEATURE ISERIES from arch code".
No one noticed until at least 3.9.
By then we'd also broken it with the optimised memcpy, copy_to/from_user
and clear_user routines. We don't want to add any more complexity to
those just to support ancient cpus, so it seems like it's a good time to
drop support for power3 and earlier.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 24 Jun 2014 08:15:57 +0000 (18:15 +1000)]
powerpc: Use standard macros for sys_sigpending() & sys_old_getrlimit()
Currently we have sys_sigpending and sys_old_getrlimit defined to use
COMPAT_SYS() in systbl.h, but then both are #defined to sys_ni_syscall
in systbl.S.
This seems to have been done when ppc and ppc64 were merged, in commit 9994a33 "Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S".
AFAICS there's no longer (or never was) any need for this, we can just
use SYSX() for both and remove the #defines to sys_ni_syscall.
Thomas Falcon [Fri, 25 Jul 2014 17:47:42 +0000 (12:47 -0500)]
powerpc: Fix endianness of flash_block_list in rtas_flash
The function rtas_flash_firmware passes the address of a data structure,
flash_block_list, when making the update-flash-64-and-reboot rtas call.
While the endianness of the address is handled correctly, the endianness
of the data is not. This patch ensures that the data in flash_block_list
is big endian when passed to rtas on little endian hosts.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Wed, 23 Jul 2014 07:20:04 +0000 (17:20 +1000)]
powerpc/perf: Fix MMCR2 handling for EBB
In the recent commit b50a6c584bb4 "Clear MMCR2 when enabling PMU", I
screwed up the handling of MMCR2 for tasks using EBB.
We must make sure we set MMCR2 *before* ebb_switch_in(), otherwise we
overwrite the value of MMCR2 that userspace may have written. That
potentially breaks a task that uses EBB and manually uses MMCR2 for
event freezing.
Fixes: b50a6c584bb4 ("powerpc/perf: Clear MMCR2 when enabling PMU") Cc: stable@vger.kernel.org Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Mon, 21 Jul 2014 09:55:13 +0000 (17:55 +0800)]
powerpc: use _GLOBAL_TOC for memmove
memmove may be called from module code copy_pages(btrfs), and it may
call memcpy, which may call back to C code, so it needs to use
_GLOBAL_TOC to set up r2 correctly.
This fixes following error when I tried to boot an le guest:
powerpc/pseries: dynamically added OF nodes need to call of_node_init
Commit 75b57ecf9 refactored device tree nodes to use kobjects such that they
can be exposed via /sysfs. A secondary commit 0829f6d1f furthered this rework
by moving the kobect initialization logic out of of_node_add into its own
of_node_init function. The inital commit removed the existing kref_init calls
in the pseries dlpar code with the assumption kobject initialization would
occur in of_node_add. The second commit had the side effect of triggering a
BUG_ON during DLPAR, migration and suspend/resume operations as a result of
dynamically added nodes being uninitialized.
This patch fixes this by adding of_node_init calls in place of the previously
removed kref_init calls.
Paul Mackerras [Sat, 19 Jul 2014 07:47:57 +0000 (17:47 +1000)]
powerpc: Fix bugs in emulate_step()
This fixes some bugs in emulate_step(). First, the setting of the carry
bit for the arithmetic right-shift instructions was not correct on 64-bit
machines because we were masking with a mask of type int rather than
unsigned long. Secondly, the sld (shift left doubleword) instruction was
using the wrong instruction field for the register containing the shift
count.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Joel Stanley [Fri, 18 Jul 2014 02:11:37 +0000 (11:41 +0930)]
powerpc: Disable doorbells on Power8 DD1.x
These processors do not currently support doorbell IPIs, so remove them
from the feature list if we are at DD 1.xx for the 0x004d part.
This fixes a regression caused by d4e58e5928f8 (powerpc/powernv: Enable
POWER8 doorbell IPIs). With that patch the kernel would hang at boot
when calling smp_call_function_many, as the doorbell would not be
received by the target CPUs:
Fixes: d4e58e5928f8 (powerpc/powernv: Enable POWER8 doorbell IPIs) Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use jump labels if configured, which means we only add a single
nop instruction to every OPAL call when the tracepoints are disabled.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have an unconditional branch that gets noped out during boot and
a load/compare/branch. We also store the tracepoint value to the
stack for the hcall_exit path to use.
By using jump labels we can simplify this to just a single nop that
gets replaced with a branch when the tracepoint is enabled:
Anton Blanchard [Wed, 28 May 2014 22:15:38 +0000 (08:15 +1000)]
powerpc/perf: Never program book3s PMCs with values >= 0x80000000
We are seeing a lot of PMU warnings on POWER8:
Can't find PMC that caused IRQ
Looking closer, the active PMC is 0 at this point and we took a PMU
exception on the transition from negative to 0. Some versions of POWER8
have an issue where they edge detect and not level detect PMC overflows.
A number of places program the PMC with (0x80000000 - period_left),
where period_left can be negative. We can either fix all of these or
just ensure that period_left is always >= 1.
This patch takes the second option.
Cc: <stable@vger.kernel.org> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A number of attempts to fix the problem by moving around code have been
unsuccessful and resulted in failed builds for some configurations and
the discovery of toolchain bugs.
Fix the problem by disabling RELOCATABLE for COMPILE_TEST builds instead.
While this is less than perfect, it avoids substantial code changes
which would otherwise be necessary just to make COMPILE_TEST builds
happy and might have undesired side effects.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Joel Stanley [Tue, 8 Jul 2014 06:38:22 +0000 (16:08 +0930)]
powerpc/perf: Clear MMCR2 when enabling PMU
On POWER8 when switching to a KVM guest we set bits in MMCR2 to freeze
the PMU counters. Aside from on boot they are then never reset,
resulting in stuck perf counters for any user in the guest or host.
We now set MMCR2 to 0 whenever enabling the PMU, which provides a sane
state for perf to use the PMU counters under either the guest or the
host.
This was manifesting as a bug with ppc64_cpu --frequency:
$ sudo ppc64_cpu --frequency
WARNING: couldn't run on cpu 0
WARNING: couldn't run on cpu 8
...
WARNING: couldn't run on cpu 144
WARNING: couldn't run on cpu 152
min: 18446744073.710 GHz (cpu -1)
max: 0.000 GHz (cpu -1)
avg: 0.000 GHz
The command uses a perf counter to measure CPU cycles over a fixed
amount of time, in order to approximate the frequency of the machine.
The counters were returning zero once a guest was started, regardless of
weather it was still running or had been shut down.
By dumping the value of MMCR2, it was observed that once a guest is
running MMCR2 is set to 1s - which stops counters from running:
This is done unconditionally in book3s_hv_interrupts.S upon entering the
guest, and the original value is only save/restored if the host has
indicated it was using the PMU. This is okay, however the user of the
PMU needs to ensure that it is in a defined state when it starts using
it.
Fixes: e05b9b9e5c10 ("powerpc/perf: Power8 PMU support") Cc: stable@vger.kernel.org Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Joel Stanley [Tue, 8 Jul 2014 06:38:21 +0000 (16:08 +0930)]
powerpc/perf: Add PPMU_ARCH_207S define
Instead of separate bits for every POWER8 PMU feature, have a single one
for v2.07 of the architecture.
This saves us adding a MMCR2 define for a future patch.
Cc: stable@vger.kernel.org Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Joel Stanley [Tue, 8 Jul 2014 06:38:20 +0000 (16:08 +0930)]
powerpc/kvm: Remove redundant save of SIER AND MMCR2
These two registers are already saved in the block above. Aside from
being unnecessary, by the time we get down to the second save location
r8 no longer contains MMCR2, so we are clobbering the saved value with
PMC5.
MMCR2 primarily consists of counter freeze bits. So restoring the value
of PMC5 into MMCR2 will most likely have the effect of freezing
counters.
Fixes: 72cde5a88d37 ("KVM: PPC: Book3S HV: Save/restore host PMU registers that are new in POWER8") Cc: stable@vger.kernel.org Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Paul Mackerras <paulus@samba.org> Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/powernv: Check for IRQHAPPENED before sleeping
Commit 8d6f7c5a: "powerpc/powernv: Make it possible to skip the IRQHAPPENED
check in power7_nap()" added code that prevents cpus from checking for
pending interrupts just before entering sleep state, which is wrong. These
interrupts are delivered during the soft irq disabled state of the cpu.
A cpu cannot enter any idle state with pending interrupts because they will
never be serviced until the next time the cpu is woken up by some other
interrupt. Its only then that the pending interrupts are replayed. This can result
in device timeouts or warnings about this cpu being stuck.
This patch fixes ths issue by ensuring that cpus check for pending interrupts
just before entering any idle state as long as they are not in the path of split
core operations.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/cell: Fix compilation with CONFIG_COREDUMP=n
Commit 046d662f4818 "coredump: make core dump functionality optional"
made the coredump optional, but didn't update the spufs code that
depends on it. That leads to build errors such as:
arch/powerpc/platforms/built-in.o: In function `.spufs_arch_write_note':
coredump.c:(.text+0x22cd4): undefined reference to `.dump_emit'
coredump.c:(.text+0x22cf4): undefined reference to `.dump_emit'
coredump.c:(.text+0x22d0c): undefined reference to `.dump_align'
coredump.c:(.text+0x22d48): undefined reference to `.dump_emit'
coredump.c:(.text+0x22e7c): undefined reference to `.dump_skip'
Fix it by adding some ifdefs in the cell code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Shengzhou Liu [Wed, 11 Jun 2014 10:10:05 +0000 (18:10 +0800)]
powerpc/fsl-booke: Add initial T208x QDS board support
Add support for Freescale T2080/T2081 QDS Development System Board.
The T2080QDS Development System is a high-performance computing,
evaluation, and development platform that supports T2080 QorIQ
Power Architecture processor, with following major features:
T2080QDS feature overview:
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP
- Dual DIMM slots up 2133MT/s with ECC
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 8MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0, SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/MMC/eMMC Card
DMA:
- Three 8-channels DMA controllers
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
T2081QDS board shares the same PCB with T1040QDS with some differences.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Shengzhou Liu [Wed, 11 Jun 2014 10:10:04 +0000 (18:10 +0800)]
powerpc/fsl-booke: Add support for T2080/T2081 SoC
The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power
Architecture processor cores with high-performance datapath acceleration
logic and network and peripheral bus interfaces required for networking,
telecom/datacom, wireless infrastructure, and mil/aerospace applications.
The T2080 SoC includes the following function and features:
- Four dual-threaded 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 Ethernet interfaces (multiple 1G/2.5G/10G MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
T2081 is a reduced personality of T2080 with following difference:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[scottwood@freescale.com: added fsl,qoriq-pci-v3.0 for U-Boot compat] Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Sat, 21 Jun 2014 00:55:33 +0000 (19:55 -0500)]
powerpc/8xx: Remove empty asm/mpc8xx.h
m8xx_pcmcia_ops was the only thing in this file (other than a comment
that describes a usage that doesn't match the file's contents); now
that m8xx_pcmcia_ops is gone, remove the empty file.
Scott Wood [Sat, 21 Jun 2014 00:42:59 +0000 (19:42 -0500)]
pcmcia: Remove m8xx_pcmcia driver
This driver doesn't build, and apparently has not built since
arch/ppc was removed in 2008 (when mk_int_int_mask was removed
from asm/irq.h, among other build errors).
A few weeks ago I asked whether anyone was actively maintaining
this code, and got no positive response:
http://patchwork.ozlabs.org/patch/352082/
So, let's remove it.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Vitaly Bordug <vitb@kernel.crashing.org> Cc: linux-pcmcia@lists.infradead.org Cc: Paul Bolle <pebolle@tiscali.nl>
Bharat Bhushan [Tue, 13 May 2014 06:48:22 +0000 (12:18 +0530)]
booke/powerpc: define wimge shift mask to fix compilation error
This fixes below compilation error on SOCs where CONFIG_PHYS_64BIT
is not defined:
arch/powerpc/kvm/e500_mmu_host.c: In function 'kvmppc_e500_shadow_map':
| arch/powerpc/kvm/e500_mmu_host.c:631:20: error: 'PTE_WIMGE_SHIFT' undeclared (first use in this function)
| wimg = (*ptep >> PTE_WIMGE_SHIFT) & MAS2_WIMGE_MASK;
| ^
| arch/powerpc/kvm/e500_mmu_host.c:631:20: note: each undeclared identifier is reported only once for each function it appears in
| make[1]: *** [arch/powerpc/kvm/e500_mmu_host.o] Error 1
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Chunhe Lan [Tue, 3 Jun 2014 10:25:14 +0000 (18:25 +0800)]
powerpc/85xx: Add T4240RDB board support
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Wed, 25 Jun 2014 01:15:51 +0000 (20:15 -0500)]
powerpc: Don't skip ePAPR spin-table CPUs
Commit 59a53afe70fd530040bdc69581f03d880157f15a "powerpc: Don't setup
CPUs with bad status" broke ePAPR SMP booting. ePAPR says that CPUs
that aren't presently running shall have status of disabled, with
enable-method being used to determine whether the CPU can be enabled.
Fix by checking for spin-table, which is currently the only supported
enable-method.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Michael Neuling <mikey@neuling.org> Cc: Emil Medve <Emilian.Medve@Freescale.com> Cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Laurent Dufour [Tue, 24 Jun 2014 08:53:59 +0000 (10:53 +0200)]
powerpc/module: Fix TOC symbol CRC
The commit 71ec7c55ed91 introduced the magic symbol ".TOC." for ELFv2 ABI.
This symbol is built manually and has no CRC value computed. A zero value
is put in the CRC section to avoid modpost complaining about a missing CRC.
Unfortunately, this breaks the kernel module loading when the kernel is
relocated (kdump case for instance) because of the relocation applied to
the kcrctab values.
This patch compute a CRC value for the TOC symbol which will match the one
compute by the kernel when it is relocated - aka '0 - relocate_start' done in
maybe_relocated called by check_version (module.c).
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com> Cc: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 24 Jun 2014 07:17:47 +0000 (17:17 +1000)]
powerpc/powernv: Remove OPAL v1 takeover
In commit 27f4488872d9 "Add OPAL takeover from PowerVM" we added support
for "takeover" on OPAL v1 machines.
This was a mode of operation where we would boot under pHyp, and query
for the presence of OPAL. If detected we would then do a special
sequence to take over the machine, and the kernel would end up running
in hypervisor mode.
OPAL v1 was never a supported product, and was never shipped outside
IBM. As far as we know no one is still using it.
Newer versions of OPAL do not use the takeover mechanism. Although the
query for OPAL should be harmless on machines with newer OPAL, we have
seen a machine where it causes a crash in Open Firmware.
The code in early_init_devtree() to copy boot_command_line into cmd_line
was added in commit 817c21ad9a1f "Get kernel command line accross OPAL
takeover", and AFAIK is only used by takeover, so should also be
removed.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Catalin Marinas [Fri, 13 Jun 2014 08:44:21 +0000 (09:44 +0100)]
powerpc/kmemleak: Do not scan the DART table
The DART table allocation is registered to kmemleak via the
memblock_alloc_base() call. However, the DART table is later unmapped
and dart_tablebase VA no longer accessible. This patch tells kmemleak
not to scan this block and avoid an unhandled paging request.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Mon, 23 Jun 2014 03:23:31 +0000 (13:23 +1000)]
powerpc/kprobes: Fix jprobes on ABI v2 (LE)
In commit 721aeaa9 "Build little endian ppc64 kernel with ABIv2", we
missed some updates required in the kprobes code to make jprobes work
when the kernel is built with ABI v2.
Firstly update arch_deref_entry_point() to do the right thing. Now that
we have added ppc_global_function_entry() we can just always use that, it
will do the right thing for 32 & 64 bit and ABI v1 & v2.
Secondly we need to update the code that sets up the register state before
calling the jprobe handler. On ABI v1 we setup r2 to hold the TOC, on ABI
v2 we need to populate r12 with the function entry point address.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 17 Jun 2014 06:15:36 +0000 (16:15 +1000)]
powerpc/ftrace: Use pr_fmt() to namespace error messages
The printks() in our ftrace code have no prefix, so they appear on the
console with very little context, eg:
Branch out of range
Use pr_fmt() & pr_err() to add a prefix. While we're at it, collapse a
few split lines that don't need to be, and add a missing newline to one
message.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 17 Jun 2014 06:15:34 +0000 (16:15 +1000)]
powerpc/ftrace: Fix inverted check of create_branch()
In commit 24a1bdc35, "Fix ABIv2 issues with __ftrace_make_call", Anton
changed the logic that creates and patches the branch, and added a
thinko in the check of create_branch(). create_branch() returns the
instruction that was generated, so if we get zero then it succeeded.
The result is we can't ftrace modules:
Branch out of range
WARNING: at ../kernel/trace/ftrace.c:1638
ftrace failed to modify [<d000000004ba001c>] fuse_req_init_context+0x1c/0x90 [fuse]
We should probably fix patch_instruction() to do that check and make the
API saner, but that's a separate patch. For now just invert the test.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 17 Jun 2014 06:15:33 +0000 (16:15 +1000)]
powerpc/ftrace: Fix typo in mask of opcode
In commit 24a1bdc35, "Fix ABIv2 issues with __ftrace_make_call", Anton
changed the logic that checks for the expected code sequence when
patching a module.
We missed the typo in the mask, 0xffff00000 should be 0xffff0000, which
has the effect of making the test always true.
That makes it impossible to ftrace against modules, eg:
Unexpected call sequence: 48000008e8410018
WARNING: at ../kernel/trace/ftrace.c:1638
ftrace failed to modify [<d000000007cf001c>] rng_dev_open+0x1c/0x70 [rng_core]
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
projects / linux-beck.git / log